Holt HI-8195PCM 28 quad spst analog switch open circuit when power off Datasheet

HI-8195, HI-8196, HI-8197
28Ω QUAD SPST ANALOG SWITCH
Open Circuit when Power Off
December 2011
GENERAL DESCRIPTION
FEATURES
The HI-8195 is a quad analog CMOS switch fabricated with Silicon-on-Insulator (SOI) technology for latch-up free operation
and maximum switch isolation. These switches are ideally
suited for applications demanding low switch leakage when the
power pins are 0V.
· CMOS analog switches with up to +/-10V Common Mode Range
· Superior ESD protection > 4KV HBM
· Fast switching time with break-before-make
· Low power
· Extended Temperature Range (-55°C to +125°C)
PIN CONFIGURATIONS (Top Views)
IN1 1
16 IN2
S1A 2
15 S2A
S1B 3
14 S2B
V- 4
13 V+
GND 5
12 VLOGIC
S4B 6
11 S3B
S4A 7
10 S3A
IN4 8
9 IN3
HI-8195PSx, HI-8195PDx
16-Pin SO or DIP package
16 S1A
Industry-standard plastic package options include 16-pin
SOIC, DIP and QFN. Ceramic packaging is available on request. All three products are offered in both industrial (-40°C to
+85°C) and extended (-55°C to +125°C) temperature range options.
· SOI switch isolation with 1nA typical Off leakage
14 IN2
The HI-8195 provides four each normally open switches when
the switch control inputs are low. The HI-8196 provides four
each normally closed switches when the switch control inputs
are low. The HI-8197 provides a combination of two normally
closed and two normally open switches.
· Switch nodes are open-circuit when chip is powered down
13 S2A
These switches conduct equally well in either direction. Power
down and Off state leakages are less than 10nA maximum.
Charge injection is less than 10pC. Switching times with a 3.3V
VLOGIC supply are typically 55ns to the On state and 35ns to
the Off state.
· Robust CMOS Silicon-on-Insulator (SOI) technology
15 IN1
The logic supply (VLOGIC) can be independently set from 2.5V
to 5V without changing the switch resistance (RON). With
V+/V- set at +/-15V and a signal range from +5V to -5V, the RON
maximum is 28W at 25°C and the maximum deviation from flat
is typically less than 10%.
· 28 W max at 25°C with Common Mode < +/-5V
S1B 1
12 S2B
V- 2
11 V+
GND 3
10 VLOGIC
S4B 4
· Avionics
· Data bus isolation
IN3 7
S3B
S3A 8
IN4 6
S4A 5
APPLICATIONS
9
HI-8195PCx
16-pin 5mm x 5mm Chip-scale package
· Sample-and-Hold circuits
· Test Equipment
· Communications Systems
(DS8195 Rev. New)
PRODUCT OPTIONS
PART TYPE IN1
HI-8195
0
1
HI-8196
0
1
HI-8197
0
1
HOLT INTEGRATED CIRCUITS
www.holtic.com
Switch 1
Open
Closed
Closed
Open
Open
Closed
IN2
0
1
0
1
0
1
Switch 2
Open
Closed
Closed
Open
Closed
Open
IN3
0
1
0
1
0
1
Switch 3
Open
Closed
Closed
Open
Closed
Open
IN4
0
1
0
1
0
1
Switch 4
Open
Closed
Closed
Open
Open
Closed
12/11
HI-8195, HI-8196, HI-8197
PIN DESCRIPTIONS
SIGNAL
FUNCTION
IN1
S1A
S1B
VGND
S4B
S4A
IN4
IN3
S3A
S3B
VLOGIC
V+
S2B
S1B
IN2
Logic Input
Switch Node
Switch Node
Supply
Supply
Switch Node
Switch Node
Logic Input
Logic Input
Switch Node
Switch Node
Supply
Supply
Switch Node
Switch Node
Logic input
V+/V- = 15.0V
70W
V+/V- = 10.0V
60W
60W
50W
50W
RON
RON
70W
DESCRIPTION
HI-8195 and HI-8197 are normally Open when input Low
Switch 1 Node
Switch 1 Node
Negative supply
Reference Ground
Switch 4 Node
Switch 4 Node
HI-8195 and HI-8197 are normally Open when input Low
HI-8196 and HI-8197 are normally Closed when input Low
Switch 3 Node
Switch 3 Node
3.3V or 5.0V Logic supply
Positive supply
Switch 2 Node
Switch 2 Node
HI-8196 and HI-8197 are normally Closed when input Low
40W
30W
20W
20W
10W
10W
-10V
-5V
0V
VSWITCH
5V
10V
Typical RON as a function of VSUPPLY and
VSWITCH (10mA switch current, 25°C)
15V
T = -55C
T = +25C
40W
30W
-15V
T = +125C
-15V
-10V
-5V
0V
VSWITCH
5V
10V
15V
Typical RON as a function of VSWITCH and
Temperature (10mA switch current, VSUPPLY =+/-15V)
HOLT INTEGRATED CIRCUITS
2
HI-8195, HI-8196, HI-8197
ABSOLUTE MAXIMUM RATINGS
(Voltages referenced to GND = 0V)
Supply Voltage, V+: ............................................................................16.5V Continuous Power Dissipation (TA=70°C):
Supply Voltage, V-:.............................................................................-16.5V
SO Package (derate 6.7mW/°C above 70°C)...................696mW
Supply Voltage, VLOGIC .........................................................................5.5V
Plastic DIP (derate 10.53 mw/°C above 70°C) .................842mW
Switch Current (either direction, DC): .................................................20mA
Thin QFN (derate 21.3mW/°C above 70°C) ...................1702mW
Peak Switch Current (1 ms pulse, 10% duty cycle max.)..................100mA
Digital Input Voltage (IN1-4):.....................................-0.3V to VLOGIC + 0.3V Storage Temperature Range: ......................................-65°C to +150°C
Operating Temperature Range: (Industrial)..........................-40°C to +85°C
(Hi-Temp) ........................-55°C to +125°C
Soldering Temperature:
(Ceramic)......................60 sec. at +300°C
(Plastic - leads).............10 sec. at +280°C
(Plastic - body) .....................+260°C Max.
Maximum Junction Temperature ........................................................175°C
NOTE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only.
Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
V+ = 15V, V- = -15V, GND = 0V. Operating temperature range (unless otherwise noted).
VLOGIC = 3.3V
PARAMETER
SYMBOL
CONDITIONS
FIGURE
RON
V+/V-=+/-15V, Vs=+/-5V
V+/V-=+/-15V, Vs=+/-10V
V+/V-=+/-10V, Vs=+/-5V
1
1
1
|ISWLEAK|
Switch voltage ± 10V, 25°C
2
|ISWLEAK|
Switch voltage ± 10V, 125°
2
|ISWLEAK|
Switch voltage ± 10V, -55°C
2
150
VLOGIC = 5.0V
MIN
TYP
MAX
MIN
18
18
20
24
27
28
28
31
32
18
18
20
UNIT
TYP
MAX
24
27
28
28
31
32
W
W
W
5
5
nA
20
20
nA
150
nA
SWITCH PARAMETERS
Switch Resistance
25°C, 10mA
Leakage
(open circuit and
power down)
LOGIC INPUTS
Input High Voltage
VIH
70
70
%VLOGIC
Input Low Voltage
VIL
Input Current
IIN
VIN = 0V or VIN=VLOGIC
VLOGIC Current
IDD1
Any state
0.5
0.5
μA
V+ Current
IDD2
Any state
0.5
0.5
μA
V- Current
IEE
Any state
TON
V+/V- = ±10V, 25°C
VS = ±10V, -55°C to +125°C
3
3
55
V+/V- = ±10V, 25°C
VS = ±10V, -55°C to +125°C
3
3
35
10V signal, 25°C
10V signal, -55°C to +125°C
4
4
30
-0.5
0.5
30
-0.5
0.5
%VLOGIC
μA
SUPPLY
-0.5
μA
-0.5
DYNAMIC PARAMETERS
Turn On Time
Turn Off time
Break-Before-Make Time
TOFF
TD
35
75
ns
ns
25
ns
ns
20
40
8
4
55
8
ns
ns
4
Charge Injection
Q
VS=0V, RS=0W, 25°C
5
-10
-10
pC
Off Isolation
RR
f = 1 MHz, 25°C
6
65
65
dB
Crosstalk
CR
f = 1 MHz, 25°C
7
90
90
dB
COFF
CON
Switch Off, 25°C
Switch On, 25°C
8
9
12
46
12
46
pF
pF
Capacitance
HOLT INTEGRATED CIRCUITS
3
HI-8195, HI-8196, HI-8197
TEST CIRCUITS
IDS
V1
SA
VS
+
-
RON = V1/IDS
+
-
VS
Figure 1 - On Resistance
+5V
0.1μF
0.1μF
VIN (HI-8196)
V+
SA
VD
+
-
Figure 2 - Off Leakage
+15V
VLOGIC
ID(OFF)
SB
A
IS(OFF)
SA
A
SB
50%
50%
50%
50%
VIN (HI-8195)
SB
VOUT
IN
VS
GND
+
-
90%
300W
35pF
V-
50%
VOUT
0.1μF
-15V
t ON
t OFF
Figure 3. Switching Times
0.1μF
+5V
+15V
VLOGIC
V+
0.1μF
5V
VIN
50%
50%
0V
VS1
VS2
S1A
S1B
S2A
S2B
IN
VOUT1
VOUT2
35pF
GND
V-
35pF
0.1μF
90%
50%
VOUT1
300W
300W
90%
VOUT2
50%
-15V
tD
Figure 4. Break-Before-Make Time Delay (HI-8197)
HOLT INTEGRATED CIRCUITS
4
tD
HI-8195, HI-8196, HI-8197
RS
+5V
+15V
VLOGIC
V+
SA
SB
VOUT
VIN
IN
VS
GND
+
-
CL
10nF
V-
DVOUT
VOUT
-15V
QINJ = CL x DVOUT
Figure 5. Charge Injection
0.1μF
0.1μF
+5V
+15V
VLOGIC
0.1μF
+15V
VLOGIC
V+
SA1
V+
SA
+5V
SB
VOUT
0.1μF
SB1
50W
IN1
VS
IN
IN2
GND
50W
V-
VS
0.1μF
SB2
VOUT
50W
-15V
SA2
GND
NC
V0.1μF
-15V
Figure 7 - Channel-to-Channel Crosstalk
Figure 6 - Off Isolation
0.1μF
+5V
+15V
VLOGIC
V+
SA
Capacitance
Meter
f=1MHz
0.1μF
0.1μF
SB
+15V
VLOGIC
V+
SA
Capacitance
Meter
f=1MHz
IN
GND
+5V
V-
SB
VS
IN
GND
V-
0.1μF
0.1μF
-15V
-15V
Figure 8 - Off Capacitance
Figure 9 - On Capacitance
HOLT INTEGRATED CIRCUITS
5
0.1μF
HI-8195, HI-8196, HI-8197
ORDERING INFORMATION
HI - 819x xx x x
PART
NUMBER
Blank
F
PART
NUMBER
LEAD
FINISH
Tin / Lead (Sn / Pb) Solder
Pb-free, RoHS compliant
TEMPERATURE
RANGE
FLOW
BURN
IN
I
-40°C TO +85°C
I
NO
T
-55°C TO +125°C
T
NO
M
-55°C TO +125°C
M
YES
PART
NUMBER
PACKAGE
DESCRIPTION
PC
16 PIN PLASTIC 5 x 5 mm CHIP SCALE (16PCS1) (No M-flow, Pb-free only)
PS
16 PIN PLASTIC NARROW BODY SOIC (16HN)
PD
16 PIN PLASTIC DIP (16P)
PART
NUMBER
FUNCTION
8195
QUAD SWITCH, NORMALLY OPEN
8196
QUAD SWITCH, NORMALLY CLOSED
8197
QUAD SWITCH, TWO NORMALLY OPEN, TWO NORMALLY CLOSED
HOLT INTEGRATED CIRCUITS
6
HI-8195, HI-8196, HI-8197
REVISION HISTORY
P/N
Rev
Date
DS8195 NEW 12/08/11
Description of Change
Initial Release
HOLT INTEGRATED CIRCUITS
7
HI-8195 PACKAGE DIMENSIONS
inches (millimeters)
16-PIN PLASTIC SMALL OUTLINE (SOIC) - NB
(Narrow Body)
.0087 ± .0012
(.220 ± .029)
.390 ± .004
(9.90 ± .10)
.236 ±.008
(5.99 ±.20)
Package Type: 16HN
.1525 ± .0025
(3.87 ± .06)
Top View
See Detail A
.0165 ± .003
(.419 ± .089)
.061 ± .007
(1.549 ± .178)
.050
BSC
(1.27)
0° to 8°
.0069 ± .0029
(.176 ± .074)
.033 ± .017
(.838 ± .432)
BSC = “Basic Spacing between Centers”
is theoretical true position dimension and
has no tolerance. (JEDEC Standard 95)
Detail A
millimeters
16-PIN PLASTIC CHIP-SCALE PACKAGE
Package Type: 16PCS1
Electrically isolated metal
heat sink on bottom of
package
3.38 ± 0.05
(0.133 ± 0.002)
3.38 ± 0.05
(0.133 ± 0.002)
Top View
5.00 ± 0.05
(0.197 ± 0.002)
Connect to any ground or
power plane for optimum
thermal dissipation
Bottom
View
5.00 ± 0.05
(0.197 ± 0.002)
.50 ± 0.05
(0.020 ± 0.002)
0.20
(0.008)
min.
0.75 ± 0.05
(0.03 ± 0.002)
0.203
(0.008)
0.025 ± 0.025
(0.001 ± 0.001)
0.80
(0.031) BSC
REF.
0.30 ± 0.05
(0.012 ± 0.002)
HOLT INTEGRATED CIRCUITS
8
BSC = “Basic Spacing between Centers”
is theoretical true position dimension and
has no tolerance. (JEDEC Standard 95)
HI-8195 PACKAGE DIMENSIONS
16-PIN PLASTIC DIP
Package Type:
16P
0.745 (18.923)
0.810 (20.574)
0.240 (6.096)
0.260 (6.604)
0.290 (7.366)
0.310 (7.874)
0.015 (0.381)
0.035 (0.889)
0.125 (3.175)
0.150 (3.810)
0.120 (3.048)
0.150 (3.810)
0.015 (0.381)
0.023 (0.584)
0.100 (2.54) BSC.
0.045 (1.143)
0.065 (1.651)
HOLT INTEGRATED CIRCUITS
9
0.008 (0.203)
0.015 (0.381)
0.300 (7.620)
0.370 (9.398)
inches (millimeters)
Similar pages