EPCOS B43255A5127M000 Alu-x product lines snap-in capacitor Datasheet

AEC-C_B43255.book Seite 1 Mittwoch, 16. April 2008 1:56 13
Aluminum electrolytic capacitors
Alu-X product lines
Snap-in capacitors
Series/Type:
Data
Sheet
Date:
B43255
April 2008
© EPCOS AG 2008. Reproduction, publication and dissemination of this publication and the information contained therein without EPCOS’ prior express consent is prohibited.
AEC-C_B43255.book Seite 2 Mittwoch, 16. April 2008 1:56 13
Snap-in capacitors
Long life – 105 °C
B43255
Long life grade capacitors
Applications
■ Frequency converters
■ Professional power supplies in industrial electronics
Features
■
■
■
■
High reliability
High CV product
RoHS-compatible
Long load life of 5000 h at 105 °C
Construction
■
■
■
■
Aluminum case, fully insulated
Snap-in solder pins to hold component in place on PC-board
Minus pole marking on the insulating sleeve
Case with safety vent
Specifications and characteristics in brief
Rated voltage VR
200 … 450 V DC
Operating temperature
range
VR ≤ 400 V DC: –40 °C … +105 °C
VR ≥ 450 V DC: –25 °C … +105 °C
Rated capacitance CR
(20 °C, 120 Hz)
47 … 1500 µF
Capacitance tolerance
±20%
Load life
(105 °C, VR, IAC,R)
5000 h
Leakage current Ileak
(20 °C, after 5 minutes)
CR VR
I leak ≤ 0.02 µA ⋅ ⎛ ------- ⋅ -------⎞
⎝ µF V ⎠
Dissipation factor (max.)
(20 °C, 120 Hz)
VR (V DC)
Low temperature stability
(impedance ratio)
(120 Hz)
Shelf life
After storage for 1000 h at 105 °C, the capacitors shall meet the requirement of load life test after reforming process. After test: VR to be applied
for 30 minutes, 24 to 48 hours before measurement.
Frequency multiplier
for rated ripple current
50 Hz
120 Hz
1 kHz
10 kHz
20 kHz
0.90
1.00
1.20
1.50
1.55
Temperature multiplier
for rated ripple current
M
Requirements:
∆C/C ≤ ±20% of initial value
tan δ ≤ 2 times initial specified limit
Ileak ≤ initial specified limit
200 ... 400
450
0.15
0.20
VR (V DC)
200 ... 400
450
Z ( – 25 °C )
--------------------------Z ( +20 °C )
4
8
tan δ
+40 °C
+55 °C
+70 °C
+85 °C
+105 °C
2.7
2.5
2.1
1.7
1.0
Please read Cautions and warnings and
Important notes at the end of this document.
2
04/08
AEC-C_B43255.book Seite 3 Mittwoch, 16. April 2008 1:56 13
Snap-in capacitors
Long life – 105 °C
B43255
Dimensional drawing
41 ±
˚ 25˚
d+1 max.
Minus pole marking
l+2 max.
Base
6.0±1*
Insulating
sleeve
0.8
0.8±0.1
±0.
1
1.5±0.1
Safety vent
on the base
Mounting
holes
ø2±0.1
.2
±0
10
KAL1095-Q-E
* = Shorter terminal (4.0 ± 0.5) is also available upon request.
Please read Cautions and warnings and
Important notes at the end of this document.
3
04/08
AEC-C_B43255.book Seite 4 Mittwoch, 16. April 2008 1:56 13
Snap-in capacitors
Long life – 105 °C
B43255
Overview of available types
VR
(V DC)
200
250
315
350
400
450
Case dimensions d × l (mm)
CR (µF)
47
22
56
22
× 30
× 25
25.4 × 25
25.4 × 25
25.4 × 30
82
22
× 25
22
× 25
25.4 × 25
30
× 30
100
22
× 30
25.4 × 25
25.4 × 30
30
× 30
120
25.4 × 25
25.4 × 30
30
× 25
30
× 30
68
150
22
× 25
30
× 25
25.4 × 30
30
× 30
35
× 30
180
22
× 30
30
× 25
25.4 × 35
35
× 30
35
× 35
× 40
220
22
× 25
25.4 × 30
30
× 30
30
× 35
35
× 30
35
270
25.4 × 25
25.4 × 35
35
× 30
30
× 40
35
× 35
35
× 45
330
25.4 × 30
30
× 30
35
× 30
35
× 35
35
× 40
35
× 50
390
25.4 × 35
30
× 35
35
× 35
35
× 40
35
× 45
470
25.4 × 40
35
× 30
35
× 40
35
× 45
35
× 50
560
30
× 35
35
× 35
35
× 45
35
× 50
680
30
× 40
35
× 40
35
× 50
820
35
× 35
35
× 45
1000
35
× 35
35
× 50
1200
35
× 40
1500
35
× 50
1800
2200
2700
Please read Cautions and warnings and
Important notes at the end of this document.
4
04/08
AEC-C_B43255.book Seite 5 Mittwoch, 16. April 2008 1:56 13
Snap-in capacitors
Long life – 105 °C
B43255
Technical data and ordering codes
VR
V DC
200
250
315
CR
120 Hz
20 °C
µF
IAC,R
120 Hz
105 °C
A
Case
dimensions
d×l
mm
Ordering code
220
270
330
390
470
560
680
820
1000
1200
1500
22
25.4
25.4
25.4
25.4
30
30
35
35
35
35
× 25
× 25
× 30
× 35
× 40
× 35
× 40
× 35
× 35
× 40
× 50
0.82
1.00
1.18
1.35
1.56
1.76
2.03
2.29
2.53
2.69
3.25
B43255A2227M000
B43255A2277M000
B43255A2337M000
B43255A2397M000
B43255A2477M000
B43255A2567M000
B43255A2687M000
B43255A2827M000
B43255A2108M000
B43255A2128M000
B43255A2158M000
150
180
220
270
330
390
470
560
680
820
1000
22
22
25.4
25.4
30
30
35
35
35
35
35
× 25
× 30
× 30
× 35
× 30
× 35
× 30
× 35
× 40
× 45
× 50
0.68
0.79
0.96
1.13
1.28
1.47
1.65
1.89
2.18
2.50
2.87
B43255E2157M000
B43255E2187M000
B43255E2227M000
B43255E2277M000
B43255E2337M000
B43255E2397M000
B43255E2477M000
B43255E2567M000
B43255E2687M000
B43255E2827M000
B43255E2108M000
82
100
120
150
180
220
270
330
390
470
560
680
22
22
25.4
30
30
30
35
35
35
35
35
35
× 25
× 30
× 25
× 25
× 25
× 30
× 30
× 30
× 35
× 40
× 45
× 50
0.48
0.57
0.64
0.78
0.86
1.00
1.20
1.33
1.52
1.74
1.98
2.27
B43255A0826M000
B43255A0107M000
B43255A0127M000
B43255A0157M000
B43255A0187M000
B43255A0227M000
B43255A0277M000
B43255A0337M000
B43255A0397M000
B43255A0477M000
B43255A0567M000
B43255A0687M000
Please read Cautions and warnings and
Important notes at the end of this document.
5
04/08
AEC-C_B43255.book Seite 6 Mittwoch, 16. April 2008 1:56 13
Snap-in capacitors
Long life – 105 °C
B43255
Technical data and ordering codes
VR
V DC
CR
120 Hz
20 °C
µF
IAC,R
120 Hz
105 °C
A
Case
dimensions
d×l
mm
Ordering code
350
82
100
120
150
180
220
270
330
390
470
560
22
25.4
25.4
25.4
25.4
30
30
35
35
35
35
× 25
× 25
× 30
× 30
× 35
× 35
× 40
× 35
× 40
× 45
× 50
0.48
0.59
0.68
0.76
0.88
1.06
1.23
1.40
1.59
1.82
2.06
B43255A4826M000
B43255A4107M000
B43255A4127M000
B43255A4157M000
B43255A4187M000
B43255A4227M000
B43255A4277M000
B43255A4337M000
B43255A4397M000
B43255A4477M000
B43255A4567M000
400
56
68
82
100
120
150
180
220
270
330
390
470
22
25.4
25.4
25.4
30
30
35
35
35
35
35
35
× 25
× 25
× 25
× 30
× 25
× 30
× 30
× 30
× 35
× 40
× 45
× 50
0.40
0.48
0.53
0.62
0.70
0.83
0.98
1.08
1.26
1.46
1.66
1.89
B43255A9566M000
B43255A9686M000
B43255A9826M000
B43255A9107M000
B43255A9127M000
B43255A9157M000
B43255A9187M000
B43255A9227M000
B43255A9277M000
B43255A9337M000
B43255A9397M000
B43255A9477M000
450
47
56
68
82
100
120
150
180
220
270
330
22
25.4
25.4
30
30
30
35
35
35
35
35
× 30
× 25
× 30
× 30
× 30
× 30
× 30
× 35
× 40
× 45
× 50
0.39
0.44
0.51
0.61
0.68
0.74
0.90
1.03
1.19
1.38
1.58
B43255A5476M000
B43255A5566M000
B43255A5686M000
B43255A5826M000
B43255A5107M000
B43255A5127M000
B43255A5157M000
B43255A5187M000
B43255A5227M000
B43255A5277M000
B43255A5337M000
Please read Cautions and warnings and
Important notes at the end of this document.
6
04/08
AEC-C_B43255.book Seite 7 Mittwoch, 16. April 2008 1:56 13
Cautions and warnings
General
Also see “Important notes” on page 9.
1
Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the
capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC
or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors
must not be used in AC applications, where the polarity may be reversed in the circuits or is
unknown.
2
The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage,
as this will result in a rapid increase of the leakage current and may damage the capacitor. It
is recommended to operate the capacitor at 70–80% of its rated voltage to optimize its service life.
3
The ripple current applied to the capacitor must be within the permitted range. An excessive
ripple current leads to impaired electrical properties and may damage the capacitor. Note that
the sum of the peak values of the ripple voltage and the DC operating voltage must not exceed the rated DC voltage.
4
Capacitors must be used within their permitted range of operating temperature. Operation at
room temperature optimizes their service life.
5
Capacitors with case diameter ≥8 mm are equipped with a safety vent. In capacitors fitted
with a lead or soldering lug, the safety vent is usually located at the base of the case. It needs
sufficient space around it to operate optimally. The following dimensions are recommended:
for case diameter d = 8 to 16 mm, more than 2 mm; for d =18 to 35 mm, more than 3 mm;
and for d = 42 mm or more, more than 5 mm.
6
Capacitors should not be mounted with the safety vent face down on the board. Do not locate
any wire or copper trace near the safety vent. Do not reverse the voltage, as this may result
in excess pressure and the leakage of electrolyte.
7
Gas is released through the safety vent when the pressure inside the capacitor is too high. A
gaseous liquid around the safety vent does not indicate a leakage of electrolyte.
8
The capacitor should be stored under conditions of normal temperature and in a non-acid,
non-alkali environment of normal humidity. Exposure to high temperatures, for example under direct sunlight, will reduce its operating life. If the capacitor is stored in an environment
containing acids or alkalis, the solderability of the leads may be affected.
9
The leakage current of an aluminum electrolytic capacitor may increase after a long period
of storage. After such storage, the capacitor must be aged by applying the rated operating
voltage for 6–8 hours before use.
10
Manual soldering:
a Soldering must be performed within the specified conditions.
Bit temperature: 350 °C; application time of soldering iron: 3 seconds.
b Ensure that the soldering iron does not touch any part of the capacitor body.
Please read Cautions and warnings and
Important notes at the end of this document.
7
04/08
AEC-C_B43255.book Seite 8 Mittwoch, 16. April 2008 1:56 13
Cautions and warnings
11
Do not apply excessive force to the leads and terminals. Do not move the capacitor after soldering it onto the PC board and do not carry the PC board by gripping the capacitor. Observe
the following rules to prevent undue stress to the capacitor:
a Do not tilt or bend the capacitor after soldering.
b Ensure that the terminal spacing matches the corresponding hole spacing on the PC
board.
12
The aluminum case is not insulated from the cathode. Do not place a conductor under the
aluminum capacitors on the PC board as this may cause a short circuit. The case and top of
capacitors used in switched mode power supplies have a high-voltage-resistant heat shrink
sleeve to ensure safe usage.
13
The leads of capacitors with a case diameter exceeding 14 mm cannot be used for fixing.
Please read Cautions and warnings and
Important notes at the end of this document.
8
04/08
Important notes
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or failure
before the end of their usual service life cannot be completely ruled out in the current state
of the art, even if they are operated as specified. In customer applications requiring a very
high level of operational safety and especially in customer applications in which the malfunction
or failure of an electronic component could endanger human life or health (e.g. in accident
prevention or life-saving systems), it must therefore be ensured by means of suitable design of
the customer application or other action taken by the customer (e.g. installation of protective
circuitry or redundancy) that no injury or damage is sustained by third parties in the event of
malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products. Consequently,
we cannot guarantee that all products named in this publication will always be available. The
aforementioned does not apply in case of individual agreements deviating from the foregoing for
customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,
SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks
registered or pending in Europe and in other countries. Further information will be found on
the Internet at www.epcos.com/trademarks.
9
04/08
Similar pages