MA-COM MASW-000822-12770T V6 Hmictm pin diode sp2t 10 watt switch Datasheet

MASW-000822-1277OT
HMICTM PIN Diode SP2T 10 Watt Switch for
0.05 - 6.0 GHz Higher Power Applications
Features
• Exceptional Broadband Performance
• Suitable for Higher Power WiMax & WLAN
Applications
• Lower Loss:
Tx = 0.40 dB @ 3.8 GHz, 22mA
Rx = 0.60 dB @ 3.8 GHz, 22mA
• Higher Isolation:
Rx-Tx = 21 dB @ 3.8 GHz
Tx-Rx = 26 dB @ 3.8 GHz
• Higher RF Input Power = 10 W C.W.
( Tx-Ant Port )
• Higher IIP3 = 65 dBm ( Tx-Ant Port ).
• Lower EVM (OFDM):
< 1.0% @ 8W Pin, ( Tx-Ant Port )
• Lead-Free 3 mm 16-Lead PQFN Package
• 100% Matte Tin Plating over Copper
• Halogen-Free “Green” Mold Compound
• RoHS* Compliant and 260°C Reflow Compatible
Rev. V6
Functional Schematic
Pin Configuration 1
Pin
Function
Pin
Function
Description
1
N/C
9
N/C
MA-COM’s MASW-000822-12770T is a Broadband,
high linearity, common anode PIN diode SPDT
switch in a lead-free 3 mm 16-lead PQFN package.
The MASW-00822-1277OT is ideally suited for 0.05
- 6.0 GHz applications, including WiMax & WLAN.
2
N/C
10
Rx
3
Tx
11
N/C
4
N/C
12
N/C
5
N/C
13
N/C
6
N/C
14
Ant
7
N/C
15
N/C
8
N/C
16
N/C
This SP2T switch offers excellent isolation to loss
ratio for both Tx and Rx states. The PIN diode
provides exceptional 10 W C.W power handling
coupled with 65 dBm IIP3 for maximum switch
performance @ 3.8GHz.
This MASW-000822-1277OT incorporates a PIN
diode die fabricated with M/A-COM’s patented
Silicon-Glass HMICTM process. This chip features
two silicon pedestals embedded in a low loss, low
dispersion glass. The diodes are formed on the top
of each pedestal. The topside is fully encapsulated
with silicon nitride and has an additional polymer
passivation layer. These polymer protective coatings
prevent damage and contamination during handling
and assembly.
1. The exposed pad centered on the package bottom must be
connected to RF and DC ground.
Ordering Information 2
Part Number
Package
MASW-000822-1277OT
1000 piece reel, 7 inch
MASW-000822-001SMB
Sample Board
2. Reference Application Note M513 for reel size information.
* Restrictions on Hazardous Substances, European Union Directive 2002/95/EC.
1
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
• North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400
is considering for development. Performance is based on target specifications, simulated results,
• India Tel: +91.80.43537383
• China Tel: +86.21.2407.1588
and/or prototype measurements. Commitment to develop is not guaranteed.
Visit www.macomtech.com for additional data sheets and product information.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.
MASW-000822-1277OT
HMICTM PIN Diode SP2T 10 Watt Switch for
0.05 - 6.0 GHz Higher Power Applications
Rev. V6
Electrical Specifications: TA = 25°C, PIN = 0 dBm, Z0 = 50 Ω
Parameter
Units
Min.
Typ.
Max.
dB
—
—
—
0.55
0.60
0.80
0.70
0.75
0.90
dB
—
—
—
0.35
0.40
0.50
0.45
0.55
0.60
Isolation, Tx to RX
Tx = +5.0 V @ +22 mA, Rx =+12V @ 0 mA
2.3 - 2.7 GHz
3.3 - 3.8 GHz
4.9 - 5.9 GHz
dB
27.0
24.5
21.0
29.5
26.5
21.5
—
—
—
Isolation, Rx to TX
Rx = +5.0 V @ +22 mA, Tx =+12V @ 0 mA
2.3 - 2.7 GHz
3.3 - 3.8 GHz
4.9 - 5.9 GHz
dB
22.5
19.5
17.5
24.5
21.5
17.5
—
—
—
Input Return Loss Tx
Tx = +5.0 V @ +22 mA, Rx =+12V @ 0 mA
2.3 - 2.7 GHz
3.3 - 3.8 GHz
4.9 - 5.9 GHz
dB
—
—
—
17
18
18
—
—
—
Input Return Loss Rx
Rx = +5.0 V @ +22 mA, Tx =+12V @ 0 mA
2.3 - 2.7 GHz
3.3 - 3.8 GHz
4.9 - 5.9 GHz
dB
—
—
—
17
18
18
—
—
—
Max.
Insertion Loss, Rx
Insertion Loss, Tx
Conditions
Rx = +5.0 V @ +22 mA, Tx =+12V @ 0 mA
2.3 - 2.7 GHz
3.3 - 3.8 GHz
4.9 - 5.9 GHz
Tx = +5.0 V @ +22 mA, Rx =+12V @ 0 mA
2.3 - 2.7 GHz
3.3 - 3.8 GHz
4.9 - 5.9 GHz
Electrical Specifications: F = 3.5 GHz, TA = 25°C, Z0 = 50 Ω 3,4,5
Parameter
Conditions
Units
Min.
Typ.
Tx Input P0.1dB
Tx = +5.0 V @ +22 mA, Rx =+12V @ 0 mA, Tx To Antenna
dBm
—
40
Tx Input P1dB
Tx = +5.0 V @ +22 mA, Rx =+12V @ 0 mA, Tx To Antenna
dBm
—
45
—
Tx 2nd Harmonic
Tx = +5.0 V @ +22 mA, Rx =+12V @ 0 mA, Pin = + 30 dBm
dBc
—
-68
—
Tx 3rd Harmonic
Tx = +5.0 V @ +22 mA, Rx =+12V @ 0 mA, Pin = + 30 dBm
dBc
—
-84
—
Tx Input
3rd Order Intercept Point
Tx = +5.0 V @ +22 mA, Rx =+12V @ 0 mA, Pin = + 10 dBm
F1 = 3.500 GHz, F2 = 3.510 GHz
dBm
—
65
—
Tx C.W. Input Power
Tx = +5.0 V @ +22 mA, Rx =+12V @ 0 mA, F= 4.0 GHz
dBm
—
—
40
Rx C.W. Input Power
Rx = +5.0 V @ +22 mA, Tx =+12V @ 0 mA, F= 4.0 GHz
dBm
—
—
33
Tx EVM (OFDM)
Tx = +5.0 V @ +22 mA, Rx =+12V @ 0 mA, Pin = +39 dBm
%
—
0.8
—
Tx EVM (OFDM)
Tx = +5.0 V @ +22 mA, Rx =+12V @ 0 mA, Pin = +40 dBm
%
—
1.2
Tx RF Switching Speed
( 10-90% RF Voltage)
Tx = +5.0 V@ +22 mA, Rx =+12V @ 0 mA
1MHz Rep Rate in Modulating Mode
ns
—
<500
—
3. Data taken at device RF leads.
4. Typical PIN diode forward voltage = +0.8 V @ 10 mA, +0.85 V @22 mA.
5. Typical PIN diode reverse voltage = +12.0 V
2
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
• North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400
is considering for development. Performance is based on target specifications, simulated results,
• India Tel: +91.80.43537383
• China Tel: +86.21.2407.1588
and/or prototype measurements. Commitment to develop is not guaranteed.
Visit www.macomtech.com for additional data sheets and product information.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.
MASW-000822-1277OT
HMICTM PIN Diode SP2T 10 Watt Switch for
0.05 - 6.0 GHz Higher Power Applications
Rev. V6
Absolute Maximum Ratings 6
@ TA = +25 °C (unless otherwise specified)
Parameter
Absolute Maximum
Forward Current
+ 100 mA
Reverse Voltage
-100 V
Operating Temperature
-40 °C to +85 °C
Storage Temperature
-55 °C to +150 °C
Junction Temperature
+175 °C
Tx Incident C.W. Power
10 W C.W.
Tx Peak Incident Power
20 W, 3 µS P.W., 1% Duty
Rx Incident C.W. Power
2 W C.W.
Cross Section View of M/A-Com PCB
6. Exceeding these limits may cause permanent damage.
D.C. Bias to RF Truth Table
RF State
TTL & D.C. Bias Conditions
Voltage at Common Anode
Low Loss Tx-Ant &
Isolation Tx-Rx
TTL = 1
+ 5V @ 22 mA ( Tx ), + 12V @ 0 mA ( Rx )
+ 0.9 V
Low Loss Ant-Rx &
Isolation Rx-Tx
TTL = 0
+ 5V @ 22 mA ( Rx ), + 12V @ 0 mA ( Tx )
+ 0.9 V
Driver and SP2T Schematic with Positive Voltage 7,8,9,10,11
Ant
DC Block
LBias
R5
+5 V
Bypass 180 Ω
DC Block
TX
DC Block
LBias
SP2T
Bypass
RX
LBias
Bypass
MADR-008888-000100
Logic Input
Driver
Ground
7. Forward Bias Diode Voltage, ΔVf @ 22 mA = + 0.9 V.
8. Reverse Bias Diode = | - ( +12 V - +0.9 V ) | = | - 11.1 | V.
3
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
• North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400
is considering for development. Performance is based on target specifications, simulated results,
• India Tel: +91.80.43537383
• China Tel: +86.21.2407.1588
and/or prototype measurements. Commitment to develop is not guaranteed.
Visit www.macomtech.com for additional data sheets and product information.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.
MASW-000822-1277OT
HMICTM PIN Diode SP2T 10 Watt Switch for
0.05 - 6.0 GHz Higher Power Applications
Rev. V6
Typical Performance Curves: TA = 25°C, Z0 = 50 Ω
Insertion Loss
Isolation
-15
0.0
-0.2
-20
TX
RX
-25
-0.4
-30
-0.6
TX
RX
-35
-0.8
-1.0
0.0
-40
1.0
2.0
3.0
4.0
5.0
6.0
-45
0.0
1.0
2.0
3.0
4.0
5.0
6.0
Frequency (GHz)
Frequency (GHz)
EVM
Tx and RX Return Loss
1.2
-20
1.1
TX
RX
-25
SPDT Series T/R Switch
1.0
System EVM Baseline
0.9
-30
0.8
0.7
-35
0.6
-40
0.0
0.5
1.0
2.0
3.0
4.0
Frequency (GHz)
5.0
6.0
15
20
25
30
35
40
Incident Power (dBm)
4
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
• North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400
is considering for development. Performance is based on target specifications, simulated results,
• India Tel: +91.80.43537383
• China Tel: +86.21.2407.1588
and/or prototype measurements. Commitment to develop is not guaranteed.
Visit www.macomtech.com for additional data sheets and product information.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.
MASW-000822-1277OT
HMICTM PIN Diode SP2T 10 Watt Switch for
0.05 - 6.0 GHz Higher Power Applications
Tx Diode Junction Temperature vs. C.W. Input Power
@ 4.0 GHz , Tj = 175°C
350
325
300
275
250
225
200
175
150
125
100
75
50
25
0
Rev. V6
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
These devices are rated at Class 1B Human Body.
Proper ESD control techniques should be used
when handling these devices.
Max Tj
(40.1 dBm)
20
25
30
35
40
45
P (dBm)
IN
This device is not for saturation power application. Exceeding
power dissipation maximum rating might result in device failure.
Lead-Free 3 mm 16-Lead PQFN†
†
Reference Application Note S2803 for lead-free solder reflow recommendations.
Meets JEDEC moisture sensitivity level 1 requirements.
5
ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions
• North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400
is considering for development. Performance is based on target specifications, simulated results,
• India Tel: +91.80.43537383
• China Tel: +86.21.2407.1588
and/or prototype measurements. Commitment to develop is not guaranteed.
Visit www.macomtech.com for additional data sheets and product information.
PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology
Solutions has under development. Performance is based on engineering tests. Specifications are
typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make
Commitment to produce in volume is not guaranteed.
changes to the product(s) or information contained herein without notice.
Similar pages