Kemet C1206F105K3RAC Surface mount ceramic chip capacitors - open mode - x7r - capacitance extension Datasheet

Product Bulletin
Surface Mount Ceramic Chip Capacitors – Open Mode - X7R - Capacitance Extensions
Outline Drawing
L
W
TIN PLATE
T
B
NICKEL PLATE
S
ELECTRODES
CONDUCTIVE METALLIZATION
Dimensions – Millimeters (Inches)
EIA Size Metric Size
Code
Code
L
Length
W
Width
B
Bandwidth
S
Seperation
0805
2012
2.0 (.079) ± 0.02 (.008)
1.25 (.049) ± 0.2 (.008)
0.5 (.020) ± 0.25 (.010)
0.75 (.030)
1206
3216
3.2 (1.26) ± 0.2(.008)
1.6 (.063) ± 0.2 (.008)
0.5 (.020) ± 0.25 (.010)
-
1210
3225
3.2 (.126) ± 0.2 (.008)
2.5 (.098) ± 0.2 (.008)
0.5 (.020) ± 0.25 (.010)
-
See Capacitance Value Table below for thickness dimension.
Capacitor Ordering Information
C 0805
F
684
K
4
R
A
C
End Metallization
C = Standard (Tin-plate
nickel barrier)
Style
C - Ceramic
Size Code
See dimension table
Failure Rate Level
A = Not Applicable
Specification
F - Open Mode
Capacitance Code, pF
First two digits represent significant figures.
Third digit specifies number of zeros. 100 pF = 101.
(Use “9” for 1.0 through 9.9 pF)
(Use “8” for 0.1 through .99 pF)
Temperature Characteristic
Designated by Capacitance
Change Over Temperature Range
R = X7R (±15%) (-55°C +125°C)
4 = 16V
Capacitance Tolerance
K = ± 10%
M = ±20%
The open-mode dimension (OM)
exceeds the termination bandwidth
dimensions: OM >BW
F-9073B 9/06
3 = 25V
Voltage
5 = 50V
Capacitance Value
Capacitance
Value (µF)
KEMET Part Number
Voltage
Capacitance
Tolerance
Thickness
Qty
7" Reel
Qty
13" Reel
0.22
C0805F224_3RAC
25
K, M
0.90 (.035) ± 0.10 (.004)
4,000
10,000
0.22
C0805F224_5RAC
50
K, M
1.25 (.049) ± 0.15 (.006)
2,500
10,000
0.47
C0805F474_4RAC
16
K, M
1.00 (.039) ± 0.10 (.004)
2,500
10,000
0.47
C0805F474_3RAC
25
K, M
1.25 (.049) ± 0.15 (.006)
2,500
10,000
0.68
C0805F684_4RAC
16
K, M
1.25 (.049) ± 0.15 (.006)
2,500
10,000
0.47
C1206F474_5RAC
50
K, M
0.90 (.035) ± 0.10 (.004)
4,000
10,000
1
C1206F105_3RAC
25
K, M
0.90 (.035) ± 0.10 (.004)
4,000
10,000
1
C1206F105_5RAC
50
K, M
1.60 (.063) ± 0.20 (.008)
2,000
8,000
2.2
C1206F225_4RAC
16
K, M
0.90 (.035) ± 0.10 (.004)
4,000
10,000
2.2
C1206F225_3RAC
25
K, M
1.60 (.063) ± 0.20 (.008)
2,000
8,000
4.7
C1206F475_4RAC
16
K, M
1.60 (.063) ± 0.20 (.008)
2,000
8,000
2.2
C1210F225_5RAC
50
K, M
1.70 (.067) ± 0.20 (.008)
2,000
8,000
4.7
C1210F475_4RAC
16
K, M
1.25 (.049) ± 0.15 (.006)
2,500
10,000
4.7
C1210F475_3RAC
25
K, M
1.70 (.067) ± 0.20 (.008)
2,000
8,000
Electrical Parameters
As detailed in the KEMET Surface Mount Catalog F3102 for X7R, with the following specific requirements
based on room temperature (25°C) parameters:
•
Operating Range: -55°C to +125°C, with no-bias capacitance shift limited to the ± 15% over that range.
•
Insulating Resistance (IR) measured after 2 minutes at rated voltage @25°C: Limit is 500 megohmmicrofarads or 10,000MΩ , whichever of the two is smaller.
•
Capacitance and Dissipation Factor (DF) are measured under the following conditions:
1kHz and 1 Vrms if capacitance * 10µF
120Hz and 0.5 Vrms if capacitance $ 10µF
•
DF limits:
50 -200 Volts ü 2.5%
16 -25 Volts ü 3.5%
6.3 / 10 Volts ü 5.0%
Soldering Process
All parts incorporate the standard KEMET barrier layer of pure nickel, with an overplate of pure tin to provide
excellent solderability as well as resistance to leaching. The recommended mounting techniques are as follows:
•
0402 / 1210 case sizes ü Solder Reflow
•
0603 / 0805 / 1206 case sizes ü Solder Wave / Solder Reflow
Marking
These chips will be supplied unmarked. If required, they can be laser-marked as an extra option.
Details on the marking format are included in KEMET Surface Mount catalog F3102.
In general, the information provided in the KEMET Surface Mount catalog F3102 applies to these
capacitors. The Information in this bulletin supplements that in the catalog
F-9073B 9/06
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Similar pages