AZETTLER AZ767-1C-12D Spdt subminiature power relay Datasheet

AZ767
SPDT SUBMINIATURE
POWER RELAY
FEATURES
•
•
•
•
•
•
Small footprint
Low cost
Class B insulation standard
Epoxy sealed version available
10 Amp switching
UL, CUR file E44211
CONTACTS
Arrangement
SPST (1 Form A)
SPDT (1 Form C)
Ratings
Resistive load:
Rated Load
UL, CUR
Material
Resistance
GENERAL DATA
Life Expectancy
Mechanical
Electrical
Minimum operations
1 x 107
1 x 105 at 5 A 240 VAC Res.
Operate Time (typical)
8 ms at nominal coil voltage
Release Time (typical)
5 ms at nominal coil voltage
(with no coil suppression)
Dielectric Strength
2500 Vrms coil to contact
(at sea level for 1 min.) 1000 Vrms between open contacts
Max. switched power: 150 W (SPST-NO) standard
1250 VA (SPST-NO) standard
90 W (SPST-NO) sensitive
750 VA (SPST-NO) sensitive
90 W (SPDT)
750 W (SPDT)
Max. switched current: 10 A AC SPST-NO standard
5 A DC SPST-NO standard
3 A AC/DC SPST-NO sensitive
3 A AC/DC SPDT
Max. switched voltage: 150* VDC or 380 VAC
Insulation
Resistance
1000 megohms min. at 20°C
500 VDC 50% RH
Dropout
Greater than 5% of nominal coil voltage
Ambient Temperature
Operating
At nominal coil voltage
-40°C (-40°F) to 90°C (194°F), standard
-40°C (-40°F) to 105°C (221°F), sensitive
-40°C (-40°F) to 130°C (266°F)
Vibration
0.062" DA at 10–50 Hz
*Note: If switching voltage is greater than 30 VDC, special
precautions must be taken. Please contact the factory.
Shock
10 g operating, 100 g damage
Enclosure
P.B.T. polyester
Terminals
Tinned copper alloy, P. C.
Max. Solder Temp.
270°C (518°F)
Max. Solder Time
5 seconds
Max. Solvent Temp.
80°C (176°F)
Max. Immersion Time
30 seconds
Weight
6 grams
Form A
10 A at 125 VAC, Res., 30k cycles [1]
10 A at 125 VAC, General Use., 100k cycles [2]
5 A at 250 VAC, General Use, 100k [1][2]
5 A at 30 VDC, Res., 100k cycles [1][2]
300 W at 120 VAC Tungsten [2]
3 A at 250 VAC, General Use, 100k cycles [1][2]
sensitive
3 A at 30 VDC, Res., 100k cycles [1][2] - sensitive
5 A at 125 VAC, Res., 100k cycles [1] - sensitive
10 LRA / 1.5 FLA at 120 VAC, 100k cycles [1]
1/10 HP at 125 VAC, 100k cycles [1]
1/16 HP at 250 VAC, 100k cycles [1]
8 A at 250 VAC, General Use, 100k cycles [2] - sensitive
high capacity
Form C
3 A at 250 VAC, General Use, 100k cycles [1][2]
3 A at 30 VDC, Res., 100k cycles [1][2]
[1] silver cadmium oxide [2] silver nickel
Silver cadmium oxide or silver nickel
<100 milliohms initially
(24 V, 1 A voltage drop method)
Storage
COIL
Power
At Pickup Voltage
(typical)
253 mW standard
113 mW sensitive
Max. Continuous
Dissipation
1.25 W at 20°C (68°F) ambient
Temperature Rise
41°C (74°F) at nominal coil voltage, standard
22°C (40°F) at nominal coil voltage, sensitive
Temperature
Max. 130°C (266°F)
NOTES
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Specifications subject to change without notice.
9/6/06 W
AZ767
RELAY ORDERING DATA
STANDARD RELAYS
COIL SPECIFICATIONS
Nominal Coil
VDC
3
Must Operate
VDC
2.25
Max. Continuous
VDC
5.0
ORDER NUMBER*
Coil
Resistance ± 10%
20
Form A (SPST)
Form C (SPDT)
AZ767–1A–3D
AZ767–1C–3D
5
3.75
8.3
55
AZ767–1A–5D
AZ767–1C–5D
6
4.5
10.0
80
AZ767–1A–6D
AZ767–1C–6D
9
6.75
15.0
180
AZ767–1A–9D
AZ767–1C–9D
12
9.0
20.0
320
AZ767–1A–12D
AZ767–1C–12D
18
13.5
30.0
720
AZ767–1A–18D
AZ767–1C–18D
24
18.0
40.0
1,280
AZ767–1A–24D
AZ767–1C–24D
48
36.0
80.0
5,120
AZ767-1A-48D
AZ767-1C-48D
*For silver nickel contacts change “-1A” to “-1AB” or “-1C” to “-1CB”. Add suffix “E” for epoxy sealed version. Add suffix “A” for gold plated version.
SENSITIVE RELAYS
COIL SPECIFICATIONS
Nominal Coil
VDC
3
Must Operate
VDC
2.25
Max. Continuous
VDC
7.5
ORDER NUMBER*
Coil
Resistance ± 10%
45
Form A (SPST)
AZ767–1A–3DS
5
3.75
12.5
125
AZ767–1A–5DS
6
4.5
15.0
180
AZ767–1A–6DS
9
6.75
22.4
400
AZ767–1A–9DS
12
9.0
30.0
720
AZ767–1A–12DS
18
13.5
44.7
1600
AZ767–1A–18DS
24
18.0
59.2
2800
AZ767–1A–24DS
*For silver nickel contacts change “-1A” to “-1AB”. For high capacity silver nickel contacts change “-1A” to “-1ABT”. Add suffix “E” for epoxy sealed
version. Add suffix “A” for gold plated version.
MECHANICAL DATA
PC BOARD LAYOUT
.059
[1.50]
.073
[1.85]
.417 MAX.
[10.59]
.740 MAX.
[18.80]
.100
[2.54]
.058
[1.49]
.300
[7.62]
5xø.052 - FORM C
4xø.052 - FORM A
[ø1.3]
.441
[11.20]
FORM C ONLY
VIEWED TOWARD TERMINALS
WIRING DIAGRAM
.614 MAX.
[15.59]
.147
[3.73]
5
1
.073
[1.85]
4
2
3
FORM C ONLY
VIEWED TOWARD TERMINALS
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
9/6/06 W
Similar pages