Order this document by MC33201/D The MC33201/2/4 family of operational amplifiers provide rail–to–rail operation on both the input and output. The inputs can be driven as high as 200 mV beyond the supply rails without phase reversal on the outputs, and the output can swing within 50 mV of each rail. This rail–to–rail operation enables the user to make full use of the supply voltage range available. It is designed to work at very low supply voltages (± 0.9 V) yet can operate with a supply of up to +12 V and ground. Output current boosting techniques provide a high output current capability while keeping the drain current of the amplifier to a minimum. Also, the combination of low noise and distortion with a high slew rate and drive capability make this an ideal amplifier for audio applications. • Low Voltage, Single Supply Operation (+1.8 V and Ground to +12 V and Ground) • Input Voltage Range Includes both Supply Rails • • • • • • • • LOW VOLTAGE RAIL–TO–RAIL OPERATIONAL AMPLIFIERS 8 NC 1 8 NC 2 7 VCC 3 6 Output VEE 4 5 NC Inputs 1 P SUFFIX PLASTIC PACKAGE CASE 626 (Single, Top View) Output Voltage Swings within 50 mV of both Rails No Phase Reversal on the Output for Over–driven Input Signals Output 1 1 8 VCC 7 Output 2 8 High Output Current (ISC = 80 mA, Typ) 1 2 1 Inputs 1 Low Supply Current (ID = 0.9 mA, Typ) D SUFFIX PLASTIC PACKAGE CASE 751 (SO–8) 600 Ω Output Drive Capability Extended Operating Temperature Ranges (–40° to +105°C and –55° to +125°C) Typical Gain Bandwidth Product = 2.2 MHz 3 6 Inputs 2 2 VEE 4 5 (Dual, Top View) Offered in New TSSOP Package Including Standard SOIC and DIP Packages 14 Operational Amplifier Function Operating Temperature Range Device MC33201D MC33201P TA= –40 ° to +105°C 14 1 1 ORDERING INFORMATION Package P SUFFIX PLASTIC PACKAGE CASE 646 SO–8 Plastic DIP 14 Si l Single MC33201VD TA = –55 ° to +125°C MC33201VP MC33202D MC33202P TA= –40 ° to +105°C D SUFFIX PLASTIC PACKAGE CASE 751A (SO–14) 1 SO–8 Plastic DIP DTB SUFFIX PLASTIC PACKAGE CASE 948G (TSSOP–14) SO–8 Plastic DIP D l Dual MC33202VD TA = –55 ° to +125°C MC33202VP MC33204D MC33204DTB SO–8 Plastic DIP SO–14 TA= –40 40 ° to +105°C 105°C MC33204P TSSOP–14 Plastic DIP Q d Quad MC33204VD MC33204VDTB MC33204VP TA = –55 55 ° to +125°C +125 C SO–14 TSSOP–14 Output 1 1 2 Inputs 1 1 4 3 13 12 VCC 4 11 5 10 Inputs 2 6 2 3 Output 2 7 Plastic DIP 9 8 Inputs 4 VEE Inputs 3 Output 3 (Quad, Top View) Motorola, Inc. 1996 MOTOROLA ANALOG IC DEVICE DATA 14 Output 4 Rev 2 1 MC33201 MC33202 MC33204 DC ELECTRICAL CHARACTERISTICS (TA = 25°C) Characteristic VCC = 2.0 V VCC = 3.3 V VCC = 5.0 V Input Offset Voltage VIO (max) MC33201 MC33202 MC33204 ± 8.0 ±10 ±12 ± 8.0 ±10 ±12 ± 6.0 ± 8.0 ±10 Output Voltage Swing VOH (RL = 10 kΩ) VOL (RL = 10 kΩ) 1.9 0.10 3.15 0.15 4.85 0.15 Power Supply Current per Amplifier (ID) 1.125 1.125 1.125 Unit mV Vmin Vmax mA Specifications at VCC = 3.3 V are guaranteed by the 2.0 V and 5.0 V tests. VEE = Gnd. MAXIMUM RATINGS Rating Symbol Value Unit VS +13 V Input Differential Voltage Range VIDR (Note 1) V Common Mode Input Voltage Range (Note 2) VCM VCC + 0.5 V to VEE – 0.5 V V Output Short Circuit Duration ts (Note 3) sec Maximum Junction Temperature TJ +150 °C Storage Temperature Tstg – 65 to +150 °C Maximum Power Dissipation PD (Note 3) mW Supply Voltage (VCC to VEE) NOTES: 1. The differential input voltage of each amplifier is limited by two internal parallel back–to–back diodes. For additional differential input voltage range, use current limiting resistors in series with the input pins. 2. The input common mode voltage range is limited by internal diodes connected from the inputs to both supply rails. Therefore, the voltage on either input must not exceed either supply rail by more than 500 mV. 3. Power dissipation must be considered to ensure maximum junction temperature (TJ) is not exceeded. (See Figure 2) DC ELECTRICAL CHARACTERISTICS (VCC = + 5.0 V, VEE = Ground, TA = 25°C, unless otherwise noted.) Figure Symbol Input Offset Voltage (VCM 0 V to 0.5 V, VCM 1.0 V to 5.0 V) MC33201: TA = + 25°C MC33201: TA = – 40° to +105°C MC33201: TA = – 55° to +125°C MC33202: TA = + 25°C MC33202: TA = – 40° to +105°C MC33202: TA = – 55° to +125°C MC33204: TA = + 25°C MC33204: TA = – 40° to +105°C MC33204: TA = – 55° to +125°C 3 VIO Input Offset Voltage Temperature Coefficient (RS = 50 Ω) TA = – 40° to +105°C TA = – 55° to +125°C 4 Characteristic Input Bias Current (VCM = 0 V to 0.5 V, VCM = 1.0 V to 5.0 V) TA = + 25°C TA = – 40° to +105°C TA = – 55° to +125°C 5, 6 Input Offset Current (VCM = 0 V to 0.5 V, VCM = 1.0 V to 5.0 V) TA = + 25°C TA = – 40° to +105°C TA = – 55° to +125°C – Common Mode Input Voltage Range – 2 Min Typ Max – – – – – – – – – – – – – – – – – – 6.0 9.0 13 8.0 11 14 10 13 17 – – 2.0 2.0 – – – – – 80 100 – 200 250 500 – – – 5.0 10 – 50 100 200 VEE – VCC mV ∆VIO/∆T µV/°C IIB nA IIO VICR Unit nA V MOTOROLA ANALOG IC DEVICE DATA MC33201 MC33202 MC33204 DC ELECTRICAL CHARACTERISTICS (continued) (VCC = + 5.0 V, VEE = Ground, TA = 25°C, unless otherwise noted.) Characteristic Large Signal Voltage Gain (VCC = + 5.0 V, VEE = – 5.0 V) RL = 10 kΩ RL = 600 Ω Output Voltage Swing (VID = ± 0.2 V) RL = 10 kΩ RL = 10 kΩ RL = 600 Ω RL = 600 Ω Figure Symbol Min Typ Max 7 AVOL 50 25 300 250 – – VOH VOL VOH VOL 4.85 – 4.75 – 4.95 0.05 4.85 0.15 – 0.15 – 0.25 60 90 – 500 25 – 50 80 – – – 0.9 0.9 1.125 1.125 Unit kV/V 8, 9, 10 V Common Mode Rejection (Vin = 0 V to 5.0 V) 11 CMR Power Supply Rejection Ratio VCC/VEE = 5.0 V/Gnd to 3.0 V/Gnd 12 PSRR Output Short Circuit Current (Source and Sink) 13, 14 ISC Power Supply Current per Amplifier (VO = 0 V) TA = – 40° to +105°C TA = – 55° to +125°C 15 ID dB µV/V mA mA AC ELECTRICAL CHARACTERISTICS (VCC = + 5.0 V, VEE = Ground, TA = 25°C, unless otherwise noted.) Characteristic Slew Rate (VS = ± 2.5 V, VO = – 2.0 V to + 2.0 V, RL = 2.0 kΩ, AV = +1.0) Figure Symbol 16, 26 SR Min Typ Max 0.5 1.0 – Unit V/µs Gain Bandwidth Product (f = 100 kHz) 17 GBW – 2.2 – MHz Gain Margin (RL = 600 Ω, CL = 0 pF) 20, 21, 22 AM – 12 – dB Phase Margin (RL = 600 Ω, CL = 0 pF) 20, 21, 22 OM – 65 – Deg 23 CS – 90 – dB BWP – 28 – kHz – – 0.002 0.008 – – – 100 – Channel Separation (f = 1.0 Hz to 20 kHz, AV = 100) Power Bandwidth (VO = 4.0 Vpp, RL = 600 Ω, THD ≤ 1 %) Total Harmonic Distortion (RL = 600 Ω, VO = 1.0 Vpp, AV = 1.0) f = 1.0 kHz f = 10 kHz 24 THD % ZO Open Loop Output Impedance (VO = 0 V, f = 2.0 MHz, AV = 10) Ω Differential Input Resistance (VCM = 0 V) Rin – 200 – kΩ Differential Input Capacitance (VCM = 0 V) Cin – 8.0 – pF – – 25 20 – – – – 0.8 0.2 – – Equivalent Input Noise Voltage (RS = 100 Ω) f = 10 Hz f = 1.0 kHz 25 Equivalent Input Noise Current f = 10 Hz f = 1.0 kHz 25 MOTOROLA ANALOG IC DEVICE DATA en in nV/ Hz pA/ Hz 3 MC33201 MC33202 MC33204 Figure 1. Circuit Schematic (Each Amplifier) VCC VCC VEE VCC Vin – Vout VCC Vin + VEE This device contains 70 active transistors (each amplifier). 4 MOTOROLA ANALOG IC DEVICE DATA Figure 2. Maximum Power Dissipation versus Temperature Figure 3. Input Offset Voltage Distribution 2500 40 PERCENTAGE OF AMPLIFIERS (%) PD(max) , MAXIMUM POWER DISSIPATION (mW) MC33201 MC33202 MC33204 8 and 14 Pin DIP Pkg 2000 TSSOP–14 Pkg 1500 SO–14 Pkg 1000 SO–8 Pkg 500 0 – 55 – 40 – 25 0 25 50 85 TA, AMBIENT TEMPERATURE (°C) 360 amplifiers tested from 3 (MC33204) wafer lots VCC = + 5.0 V VEE = Gnd TA = 25°C DIP Package 35 30 25 20 15 10 5.0 0 –10 – 8.0 – 6.0 – 4.0 – 2.0 0 2.0 4.0 6.0 VIO, INPUT OFFSET VOLTAGE (mV) 125 Figure 4. Input Offset Voltage Temperature Coefficient Distribution 40 30 I IB , INPUT BIAS CURRENT (nA) PERCENTAGE OF AMPLIFIERS (%) 200 360 amplifiers tested from 3 (MC33204) wafer lots VCC = + 5.0 V VEE = Gnd TA = 25°C DIP Package 20 10 0 – 50 – 40 – 30 – 20 –10 0 10 20 30 40 VCC = + 5.0 V VEE = Gnd 160 120 VCM = 0 V to 0.5 V 80 VCM > 1.0 V 40 0 – 55 – 40 – 25 50 TCVIO, INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT (µV/°C) A VOL , OPEN LOOP VOLTAGE GAIN (kV/V) 100 50 0 – 50 –100 VCC = 12 V VEE = Gnd TA = 25°C – 200 0 2.0 4.0 6.0 8.0 10 VCM, INPUT COMMON MODE VOLTAGE (V) MOTOROLA ANALOG IC DEVICE DATA 25 70 85 125 Figure 7. Open Loop Voltage Gain versus Temperature 150 –150 0 TA, AMBIENT TEMPERATURE (°C) Figure 6. Input Bias Current versus Common Mode Voltage I IB , INPUT BIAS CURRENT (nA) 10 Figure 5. Input Bias Current versus Temperature 50 – 250 8.0 12 300 260 220 180 140 VCC = + 5.0 V VEE = Gnd RL = 600 Ω ∆VO = 0.5 V to 4.5 V 100 – 55 – 40 – 25 0 25 70 85 TA, AMBIENT TEMPERATURE (°C) 105 125 5 MC33201 MC33202 MC33204 Figure 8. Output Voltage Swing versus Supply Voltage RL = 600 Ω TA = 25°C 10 8.0 6.0 4.0 2.0 0 ±1.0 VCC VSAT, OUTPUT SATURATION VOLTAGE (V) VO, OUTPUT VOLTAGE (Vpp ) 12 Figure 9. Output Saturation Voltage versus Load Current ± 2.0 ± 3.0 ± 4.0 ± 5.0 VCC,VEE SUPPLY VOLTAGE (V) TA = – 55°C TA = 125°C VCC – 0.4 V TA = – 55°C CMR, COMMON MODE REJECTION (dB) VCC = + 6.0 V VEE = – 6.0 V 3.0 RL = 600 Ω AV = +1.0 TA = 25°C PSR, POWER SUPPLY REJECTION (dB) VEE 20 15 80 60 40 120 100 PSR+ 80 60 PSR– 40 VCC = + 6.0 V VEE = – 6.0 V TA = – 55° to +125°C 0 100 k 1.0 M VCC = + 6.0 V VEE = – 6.0 V TA = – 55° to +125°C 20 1.0 M Figure 12. Power Supply Rejection versus Frequency 6 10 IL, LOAD CURRENT (mA) 100 0 10 k 100 k f, FREQUENCY (Hz) 1.0 k 10 k f, FREQUENCY (Hz) 5.0 0 I SC , OUTPUT SHORT CIRCUIT CURRENT (mA) VO, OUTPUT VOLTAGE (Vpp ) 6.0 100 VEE + 0.2 V Figure 11. Common Mode Rejection versus Frequency 9.0 10 TA = 25°C TA = 125°C ± 6.0 12 20 VEE + 0.4 V VCC = + 5.0 V VEE = – 5.0 V Figure 10. Output Voltage versus Frequency 0 1.0 k VCC – 0.2 V TA = 25°C 10 100 1.0 k 10 k f, FREQUENCY (Hz) 100 k 1.0 M Figure 13. Output Short Circuit Current versus Output Voltage 100 Source 80 60 Sink 40 VCC = + 6.0 V VEE = – 6.0 V TA = 25°C 20 0 0 1.0 2.0 3.0 4.0 5.0 6.0 Vout, OUTPUT VOLTAGE (V) MOTOROLA ANALOG IC DEVICE DATA MC33201 MC33202 MC33204 Figure 15. Supply Current per Amplifier versus Supply Voltage with No Load I CC , SUPPLY CURRENT PER AMPLIFIER (mA) 150 125 VCC = + 5.0 V VEE = Gnd 100 Source 75 Sink 50 25 0 – 55 – 40 – 25 0 25 70 85 TA, AMBIENT TEMPERATURE (°C) 105 125 2.0 1.6 TA = 125°C 1.2 TA = 25°C 0.8 TA = – 55°C 0.4 0 ±0 Figure 16. Slew Rate versus Temperature –Slew Rate 0.5 25 70 85 105 0 – 55 – 40 – 25 0 25 70 85 105 Figure 18. Voltage Gain and Phase versus Frequency Figure 19. Voltage Gain and Phase versus Frequency 40 VS = ± 6.0 V TA = 25°C RL = 600 Ω 80 120 2 A2 B 1 B 10 A 1.0 125 30 – 30 10 k 2.0 TA, AMBIENT TEMPERATURE (°C) 50 –10 VCC = + 2.5 V VEE = – 2.5 V f = 100 kHz TA, AMBIENT TEMPERATURE (°C) 70 1A – Phase, CL = 0 pF 1B – Gain, CL = 0 pF 2A – Phase, CL = 300 pF 2B – Gain, CL = 300 pF 100 k ± 6.0 3.0 1.0 M f, FREQUENCY (Hz) MOTOROLA ANALOG IC DEVICE DATA 1 A 160 200 240 10 M A VOL, OPEN LOOP VOLTAGE GAIN (dB) , OPEN LOOP VOLTAGE GAIN (dB) VOL 0 4.0 GBW, GAIN BANDWIDTH PRODUCT (MHz) +Slew Rate 1.0 O , EXCESS PHASE (DEGREES) SR, SLEW RATE (V/µ s) VCC = + 2.5 V VEE = – 2.5 V VO = ± 2.0 V 0 – 55 – 40 – 25 ± 2.0 ± 3.0 ± 4.0 ± 5.0 VCC, VEE, SUPPLY VOLTAGE (V) Figure 17. Gain Bandwidth Product versus Temperature 2.0 1.5 ±1.0 70 30 – 30 10 k 1A – Phase, VS = ± 6.0 V 1B – Gain, VS = ± 6.0 V 2A – Phase, VS = ± 1.0 V 2B – Gain, VS = ± 1.0 V 100 k 2 B 1.0 M 80 1 A 2 A 10 –10 40 CL = 0 pF TA = 25°C RL = 600 Ω 50 1 B 125 120 160 200 240 10 M f, FREQUENCY (Hz) 7 O , EXCESS PHASE (DEGREES) I SC , OUTPUT SHORT CIRCUIT CURRENT (mA) Figure 14. Output Short Circuit Current versus Temperature MC33201 MC33202 MC33204 Figure 20. Gain and Phase Margin versus Temperature 75 50 50 VCC = + 6.0 V VEE = – 6.0 V RL = 600 Ω CL = 100 pF 40 30 40 30 20 20 10 10 Gain Margin 0 – 55 – 40 – 25 0 25 70 85 105 O M , PHASE MARGIN (DEGREES) 60 A , GAIN MARGIN (dB) M O M , PHASE MARGIN (DEGREES) 60 60 60 VCC = + 6.0 V VEE = – 6.0 V TA = 25°C 45 30 15 0 0 125 10 100 60 Gain Margin 50 14 12 10 40 8.0 30 6.0 20 4.0 10 2.0 0 10 AV = 100 120 90 AV = 10 60 30 VCC = + 6.0 V VEE = – 6.0 V VO = 8.0 Vpp TA = 25°C 0 100 1.0 k CL, CAPACITIVE LOAD (pF) VEE = – 5.0 V RL = 600 Ω AV = 1000 0.1 0.01 AV = 100 AV = 10 AV = 1.0 0.001 10 100 1.0 k f, FREQUENCY (Hz) 8 10 k 100 k en , EQUIVALENT INPUT NOISE VOLTAGE (nV/ Hz) THD, TOTAL HARMONIC DISTORTION (%) 1.0 VCC = + 5.0 V TA = 25°C VO = 2.0 Vpp 10 k f, FREQUENCY (Hz) Figure 24. Total Harmonic Distortion versus Frequency 10 0 100 k 150 0 1.0 k 100 10 k Figure 23. Channel Separation versus Frequency A , GAIN MARGIN (dB) M CS, CHANNEL SEPARATION (dB) O M , PHASE MARGIN (DEGREES) Phase Margin 1.0 k RT, DIFFERENTIAL SOURCE RESISTANCE (Ω) 16 70 15 Gain Margin Figure 22. Gain and Phase Margin versus Capacitive Load VCC = + 6.0 V VEE = – 6.0 V RL = 600 Ω AV = 100 TA = 25°C 45 30 TA, AMBIENT TEMPERATURE (°C) 80 75 Phase Margin A , GAIN MARGIN (dB) M 70 Phase Margin Figure 25. Equivalent Input Noise Voltage and Current versus Frequency 50 5.0 VCC = + 6.0 V VEE = – 6.0 V TA = 25°C 40 30 4.0 3.0 Noise Voltage 20 10 2.0 1.0 Noise Current 0 10 100 1.0 k 10 k 0 100 k i n , INPUT REFERRED NOISE CURRENT (pA/ Hz) 70 Figure 21. Gain and Phase Margin versus Differential Source Resistance f, FREQUENCY (Hz) MOTOROLA ANALOG IC DEVICE DATA MC33201 MC33202 MC33204 General Information Circuit Information The MC33201/2/4 family of operational amplifiers are unique in their ability to swing rail–to–rail on both the input and the output with a completely bipolar design. This offers low noise, high output current capability and a wide common mode input voltage range even with low supply voltages. Operation is guaranteed over an extended temperature range and at supply voltages of 2.0 V, 3.3 V and 5.0 V and ground. Since the common mode input voltage range extends from VCC to VEE, it can be operated with either single or split voltage supplies. The MC33201/2/4 are guaranteed not to latch or phase reverse over the entire common mode range, however, the inputs should not be allowed to exceed maximum ratings. Rail–to–rail performance is achieved at the input of the amplifiers by using parallel NPN–PNP differential input stages. When the inputs are within 800 mV of the negative rail, the PNP stage is on. When the inputs are more than 800 mV greater than VEE, the NPN stage is on. This switching of input pairs will cause a reversal of input bias currents (see Figure 6). Also, slight differences in offset voltage may be noted between the NPN and PNP pairs. Cross–coupling techniques have been used to keep this change to a minimum. In addition to its rail–to–rail performance, the output stage is current boosted to provide 80 mA of output current, enabling the op amp to drive 600 Ω loads. Because of this high output current capability, care should be taken not to exceed the 150°C maximum junction temperature. VCC = + 6.0 V VEE = – 6.0 V RL = 600 Ω CL = 100 pF TA = 25°C Figure 27. Small Signal Transient Response VCC = + 6.0 V VEE = – 6.0 V RL = 600 Ω CL = 100 pF TA = 25°C V , OUTPUT VOLTAGE (50 mV/DIV) O V , OUTPUT VOLTAGE (2.0 mV/DIV) O Figure 26. Noninverting Amplifier Slew Rate t, TIME (5.0 µs/DIV) t, TIME (10 µs/DIV) V , OUTPUT VOLTAGE (2.0 V/DIV) O Figure 28. Large Signal Transient Response VCC = + 6.0 V VEE = – 6.0 V RL = 600 Ω CL = 100 pF AV = 1.0 TA = 25°C t, TIME (10 µs/DIV) Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. MOTOROLA ANALOG IC DEVICE DATA 9 MC33201 MC33202 MC33204 OUTLINE DIMENSIONS 8 P SUFFIX PLASTIC PACKAGE CASE 626–05 ISSUE K 5 NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. –B– 1 4 F L C J –T– N SEATING PLANE D M K 0.13 (0.005) M T A B M M D SUFFIX PLASTIC PACKAGE CASE 751–05 (SO–8) ISSUE R D A 8 5 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETERS. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. C 0.25 H E M B M 1 4 e h A C X 45 _ SEATING PLANE DIM A A1 B C D E e H h L q 0.10 A1 B 0.25 M C B 14 8 1 7 S A L S q P SUFFIX PLASTIC PACKAGE CASE 646–06 ISSUE L B A F L C J N H 10 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC ––– 10_ 0.030 0.040 G H B MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC ––– 10_ 0.76 1.01 DIM A B C D F G H J K L M N –A– NOTE 2 G D SEATING PLANE K M MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.18 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ NOTES: 1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 4. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M N INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.300 BSC 0_ 10_ 0.015 0.039 MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.62 BSC 0_ 10_ 0.39 1.01 MOTOROLA ANALOG IC DEVICE DATA MC33201 MC33202 MC33204 OUTLINE DIMENSIONS D SUFFIX PLASTIC PACKAGE CASE 751A–03 (SO–14) ISSUE F –A– 14 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 8 –B– 1 P 7 PL 0.25 (0.010) 7 G B M M R X 45 _ C F –T– 0.25 (0.010) M T B S A S 0.10 (0.004) M T U V S N 14 L/2 0.25 (0.010) 8 M B –U– L PIN 1 IDENT. 0.15 (0.006) T U N F 7 1 S DETAIL E ÇÇÇ ÉÉÉ ÇÇÇ ÉÉÉ ÇÇÇ K A –V– K1 J J1 SECTION N–N –W– C 0.10 (0.004) –T– SEATING PLANE D G INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 NOTES: 1 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2 CONTROLLING DIMENSION: MILLIMETER. 3 DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4 DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5 DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6 TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7 DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE –W–. S S 2X MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 DTB SUFFIX PLASTIC PACKAGE CASE 948G–01 (TSSOP–14) ISSUE O 14X K REF 0.15 (0.006) T U J M K D 14 PL SEATING PLANE DIM A B C D F G J K M P R H DETAIL E DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 ––– 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.50 0.60 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 ––– 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.020 0.024 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 MOTOROLA ANALOG IC DEVICE DATA ◊ 11 MC33201/D *MC33201/D*