Dubilier DPG47CB400 Capacitors aluminium electrolytic high temp. snap-in dpg Datasheet

CAPACITORS
ALUMINIUM ELECTROLYTIC HIGH TEMP. SNAP-IN DPG
Long-life grade (up to 2000 hours @ 105°C)
SECTION 1
Standard snap-in pin style
Case size options
The DPG is a snap-in electrolytic capacitor featuring a higher
degree of volumetric efficiency than previous types.
The product is particularly suited for the high-voltage end of
switching power supplies. The high ripple current capability is very
useful in motor-drive applications.
SPECIFICATION
Item
Electrical Characteristics
Operating Temperature Range
-40° to +105°C -25° to +105°C
Rate Working Voltage Range
6.3 to 100VDC 160 to 450VDC
Capacitance Tolerance
DC Current Leakage (µA)
±20% (At 20°C, 120Hz)
I = ≤0.02 CV, L= 20m/m, l= 0.03mA Whichever is smaller.
(At 25°C, After 5 Minutes)
Where, l: Leakage Current (µA) C: Nominal Capacitance (µF) V: Rated Voltage (V)
Dissipation Factor (tand∂) Rate Voltage (V)
6.3
10
16
25
D.F (%)
60
55
50
45
35
50
63-100
160-450
35
30
30
15
* Note: 15% For D = 35m/m or L = 20m/m (At 20°C, 120Hz)
(WV = 6.3 to 100V For capacitor whose capacitance exceeds 1000µF
The value of D.F (%) is increased by 2% for every addition of 1000µF
Low Temperature
Characteristics (120Hz)
Rated Voltage (V)
Load Life
6.3-16
25
35
50-63 80-100 160-400
450
Z(–25°C) / (Z+20°C)
4
3
3
2
2
4
8
Z(–40°C) / (Z+20°C)
15
10
8
6
5
-
-
The following specifications shall be satisfied when the capacitors are restored to
20°C after the rated voltage with maximum ripple current is applied for 2000 hours
at 105°C.
Capacitance Change
D.F
Leakage Current
Shelf Life
≤±20% of the initial value
≤200% of the initial specified value
≤ the initial specified value
The following specifications shall be satisfied when the capacitors are restored to
25°C after exposing them for 1000 hours at 105°C without voltage applied.
Capacitance Change
D.F
Leakage Current
≤±20% of the initial value
≤150% of the initial specified value
≤ 150% of the initial specified value
ORDERING INFORMATION
DPG
47
AC
400
Range
Capacitance
µf
Case Code
(see below)
Voltage
Two letter case code AC = 22.4mm dia. x 30mm height.
Diameter
A = 22.4mm
B = 25mm
C = 30mm
D = 35.5mm
Height
A = 20mm
B = 25mm
C = 30mm
D = 35mm
E = 40mm
F = 45mm
G = 50mm
69
Fax: 01371 875075
www.dubilier.co.uk
Tel: 01371 875758
CAPACITORS
ALUMINIUM ELECTROLYTIC HIGH TEMP. SNAP-IN DPG
SECTION 1
RIPPLE CURRENT MULTIPLIERS
1) Maximum rms ripple currents at 120Hz, 85°C and 105°C are given in the table.
2) Temperature multiplying factor;
Where capacitors are operated at temperature other than 105°C, the maximum ripple current must be multiplied by the figure
shown in the table below.
3) Frequency multiplying factor;
If capacitors are used to filter circuits at a frequency other than 120Hz, the rated 120Hz rms ripple current shown must be
multiplied by the factor shown in the table below.
AMBIENT TEMP./MULTIPLYING FACTOR
FREQUENCY/MULTIPLYING FACTOR
Frequency coefficient
Temperature coefficient
Temperature ( °C )
Factor
60
70
85
105
Freq(Hz)/Cap(uF)
50
60
120
1K
2.37
2.17
1.67
1.00
6.3 to 100V
0.88
0.90
1.00
1.15
10K - 00K
1.16
160 to 250V
0.85
0.88
1.00
1.15
1.20
315 to 450V
0.88
0.9
1.00
1.10
1.15
OUTLINE DRAWING
0.9 +0.2/-0.1
0.8 ±0.1
10
Vinyl Sleeve
.1
±0
Negative
6.0 ±1
3.5
Safety Vent
L ±2
D ±1
6 ±1
D ±1
Mounting Holes
on Chassis
1.5 ±0.1
Terminals
70
Fax: 01371 875075
www.dubilier.co.uk
Tel: 01371 875758
CAPACITORS
ALUMINIUM ELECTROLYTIC HIGH TEMP. SNAP-IN DPG
Max Ripple Current
[A] rms
(120Hz/105°C)
1.30
1.84
1.90
47000
35.5x45
22.4x25
4700
25x30
30x25
6800
25x25
25V
22.4x40
10000
25x35
30x30
25x45
15000
30x35
35.5x30
W.V. 22000
30x45
Cap
Case
Size
35.5x35
[µF]
øDxL[mm]
33000
35.5x50
5.4
4700
6800
35V
10000
15000
22000
50V 2200
3300
SECTION 1
W.V.
Cap
Case Size
[µF]
øDxL[mm]
6800
25x25
10000
20x30
15000
25x25
22000
25x30
10V
25x45
33000
30x35
35.5x30
47000
30x45
35x35
68000
35.5x50
16V 6800
22.4x25
22.4x30
10000
25x25
22.4x40
15000
25x35
30x30
25x45
22000
30x35
33000
30x45
35.5x35
2.25
3.3
3.8
5.5
1.55
1.95
2.55
3.3
4.30
1.79
1.85
2.40
3.15
3.75Current
Max Ripple
[A] rms
5.40
(120Hz/105°C)
22.4x35
1.80
25x25
22.4x40
25x35
2.70
30x30
25x45
30x35
3.30
35.5x30
30x45
3.91
35.5x35
35.5x50
4.59
22.4x30
1.55
24.4x35
1.87
25x30
71
Fax: 01371 875075
www.dubilier.co.uk
Tel: 01371 875758
CAPACITORS
ALUMINIUM ELECTROLYTIC HIGH TEMP. SNAP-IN DPG
SECTION 1
W.V.
Cap
Case Size Max Ripple Current
[µF]
øDxL[mm]
[A] rms
(120Hz/105°C)
22.4x45
25x40
4700
30x30
2.25
35.5x25
25x50
50V 6800
30x40
3.25
35.5x30
10000
30x50
4.00
35.5x40
15000
35.5x50
4.77
1000
20x25
1.10
1500
22.4x30
1.30
25x25
2200
22.4x35
1.70
25x30
63V
22.4x50
3300
25x40
2.10
30x30
35.5x25
25x50
4700
30x40
2.80
35.5x30
6800
30x50
3.65
35.5x40
10000
35.5x50
4.40
1000
1500
80V 2200
3300
4700
6800
680
100V 1000
22.4x30
25x25
22.4x35
25x30
22.4x45
25x35
30x30
35.5x25
25x50
30x40
35.5x30
30x50
35.5x40
35.5x50
24.4x25
24.4x35
25x30
1.20
1.45
2.00
W.V.
Cap
Case Size Max Ripple Current
[µF]
øDxL[mm]
[A] rms
(120Hz/105°C)
22.4x45
25x40
1500
30x30
1.95
35.5x25
100V
25x50
2200
30x40
2.53
35.5x30
3300
30x50
3.25
35.5x40
4700
35.5x50
4.53
220
22.4x25
0.66
330
24.4x25
1.20
470
22.4x35
1.28
680
22.4x45
1.64
160V
25x35
1000
25x45
2.17
30x35
1500
30x45
2.62
35.5x35
2200
35.5x50
3.34
220
330
200V
470
680
1000
1500
250V 220
W.V.
Cap
Case Size
[µF]
øDxL[mm]
330
22.4x40
30x25
250V 470
30x30
680
35.5x35
1000
35.5x40
47
22.4x30
400V 68
22x25
100
22.4x35
25x30
25x45
220
30x35
35.5x30
330
30x45
35.5x40
470
35x40
Max Ripple Current
[A] rms
(120Hz/105°C)
1.21
1.52
1.92
2.3
0.35
0.49
0.62
1.00
1.40
1.75
22.4x25
0.78
22.4x30
1.20
25x25
22.4x35
25x35
1.40
25x30
25x40
1.75
30x30
30x45
2.30
35.5x35
35.5x50
2.21
22.4x30
0.97
25x25
2.40
3.30
4.72
1.04
1.43
72
Fax: 01371 875075
www.dubilier.co.uk
Tel: 01371 875758
Similar pages