NKK LP0125CCKW015CB General specification Datasheet

Toggles
Series LP01
Short Body Pushbuttons
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
50 milliohms maximum (DC2 ~ 4V 100mA)
200 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum
1,500V AC minimum between contacts and case for 1 minute minimum
Mechanical Life:
500,000 operations minimum
Electrical Life:
50,000 operations minimum for 3A @ 125V/250V AC & 3A @ 30V DC
100,000 operations minimum for 1A @ 125V/250V AC & 1A @ 30V DC
Nominal Operating Force:
1.5 ± 0.7N for Single Pole; 3.0 ± 1.2N for Double Pole
Contact Timing:
Nonshorting (break-before-make)
Travel:
Total Travel .118” (3.0mm)
D
Materials & Finishes
Actuator:
Housing:
Base:
Movable Contact:
Stationary Contacts:
Slides
Lamp Terminals:
Environmental Data
Tactiles
Operating Temperature Range:
Humidity:
Vibration:
Tilt
Shock:
Installation
Touch
Mounting Torque:
Soldering Time & Temperature:
Cleaning:
Standards & Certifications
Flammability Standards:
UL:
Accessories
Indicators
3A @ 125V AC or 3A @ 250V AC or 3A @ 30V DC
Other Ratings
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Power Level (silver):
Polycarbonate
Bushing mount: Glass fiber reinforced polyamide (UL94V-0);
Snap in mount: Polybutylene terephthalate (PBT) (UL94V-0)
Glass fiber reinforced polyamide (UL94V-0)
Phosphor bronze & silver with silver plating
Common terminal: Phosphor bronze with silver plating;
Contact terminals: Phosphor bronze with tin plating
Phosphor bronze with tin plating
–10°C through +50°C (+14°F through +122°F) for Illuminated
–25°C through +70°C (–13°F through +158°F) for Nonilluminated
90 ~ 95% humidity for 240 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
0.8Nm (7.08 lb • in) maximum
Manual Soldering: See Profile A in Supplement section.
Hand clean locally with alcohol based solution
UL94V-0 housing & base
File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” or “/CUL” to end of part number to order UL recognized switch.
All single & double pole models recognized at 3A @ 125V/250V AC or 3A @ 30V DC.
Supplement
Note: The spot illuminated switches do not have UL approval and cannot be ordered with the
markings.
D68
www.nkkswitches.com
7/19/17
Toggles
Series LP01
Rockers
Distinctive Characteristics
Pushbuttons
Environmentally friendly components and packaging materials meet RoHS Directive
restricting use of hazardous materials. Suited for lead-free soldering because of
heat resistant resin materials.
Smooth, slightly concave surface of cap designed to
fit fingertip. Unique design and construction of cap
prevents its removal and limits tampering.
D
Keylocks
Bright LED illumination in choice of red, green
or amber through translucent white cap. Spot
illumination in red, green or amber enhanced
by black cap.
Programmable Illuminated PB
Short Body Pushbuttons
Rotaries
Short body of .551” (14.0mm) conserves behindpanel space.
Slides
Installation options include 16.0mm bushing mount or
17.3mm snap-in mount.
Tilt
Tactiles
Combination solder lug and .110” quick connect
terminals are epoxy sealed to prevent entry of flux, dust,
or other contaminants.
Touch
Crisp actuation and clear circuit status provided by snap-action
contact mechanism. Arc barrier between movable contacts protects
against crossover.
Supplement
Accessories
Indicators
Actual Size
www.nkkswitches.com
D69
Series LP01
Toggles
Short Body Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
1
5
Poles
C
C
1
SPDT
C
Bushing
2
DPDT
M
Snap-in
Housing
(ON)
K
LEDs
Black
( ) = Momentary
5C
Red
5D
Amber
5F
Green
IMPORTANT:
Rotaries
Cap Color
Nonilluminated
A
Black with
Spot Illumination
B
White
Nonilluminated Cap Colors
No
Nonilluminated
Code
Switches are supplied without UL & cULus markings unless
specified. UL & cULus recognized only when ordered with
marking on switch. Specific models, ratings, & ordering
instructions are noted on the General Specifications page.
Spot illuminated switches do not have UL approval and
cannot be ordered with the markings.
Slides
B
Silver Rated
3A @ 125V AC/250V AC
W01
Solder Lug/
Quick Connect Terminals
Circuit
ON
5C
Contacts & Terminals
D
5
W01
K
Mounting Types
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
LP01
A
Black
C
Red
F
Green
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Tactiles
LP0115CCKW015CB
White Cap
Red LED
Tilt
SPDT
ON-(ON) Circuit
Bushing Mount
Black Housing
Touch
Silver Contacts
Rated 3A @ 125/250V AC;
Solder Lug/Quick Connect Terminals
POLES & CIRCUIT
Supplement
Accessories
Indicators
Plunger Position
( ) = Momentary
Connected Terminals
Throw & Power/Lamp Schematics
Normal
Down
Normal
Down
LP0115
ON
(ON)
1-3
1-2
LP0125
ON
(ON)
Pole
Model
SP
DP
Note: Terminal markings “COM, NO, NC, L,
+ and – ” are actually on the switch;
terminal numbers are not on the switch.
1 (COM)
SPDT
3
1 (COM)
D70
1-3
4-6
1-2
www.nkkswitches.com
4-5
DPDT
3
L (+)
(-) L
L (+)
(-) L
2
2
4
6
5
Series LP01
Toggles
Short Body Pushbuttons
MOUNTING TYPES
M
Snap-in
.681” (17.3mm) Diameter
Rockers
Bushing
.630” (16.0mm) Diameter
Recommended
Panel Thickness:
0.2
(18.1) +– 0.0
.713
(1.7) +– 0.0
0.1
.067
0.2
(16.0) +– 0.0
Dia
.630
Pushbuttons
This mounting option is
supplied with a steel
hexagon nut with nickel plating.
Recommended
Panel Thickness:
0.1
(7.5) –+ 0.0
.295
.079” ~ .256”
(2.0mm ~ 6.5mm)
.039” ~ .126”
(1.0mm ~ 3.2mm)
(17.3)
.681
(21.0) Min
.827
(25.0) Min
.984
Allow .984” (25.0mm) distance from center-to-center
between switches when mounted side-by-side.
D
0.2
(1.1) +– 0.0
R
.043
+ 0.2
– 0.0
Dia
Allow .827” (21.0mm) distance from center-to-center
between switches when mounted side-by-side.
K
Black
Keylocks
HOUSING
Housing available in black only. The one-piece body and bezel have a matte finish.
Solder Lug/
.110” (2.8mm) Quick Connect
Power Level
3A @ 125V AC/250V AC; 3A @ 30V DC
Epoxy Seal
(7.3)
.287
(2.0)
.079
(2.8)
.110
Slides
Silver Contacts
Rotaries
CONTACT MATERIALS, RATINGS, & TERMINALS
W01
(0.6) R
.024
(1.2)
.047
Thk = (0.5)
.020
Tactiles
Note: If used at 1A @ 125V AC/250V AC or 1A @ 30V DC,
electrical life will be 100,000 operations minimum.
LED COLORS & SPECIFICATIONS
5D
5F
Red
Amber
Green
Maximum Forward Current
I FM
30mA
30mA
30mA
Typical Forward Current
IF
20mA
20mA
20mA
Forward Voltage
VF
1.95V
2.0V
2.1V
Maximum Reverse Voltage
VRM
5V
5V
5V
Current Reduction Rate Above 25°C
∆I F
0.41mA/°C
0.29mA/°C
0.39mA/°C
No Code
–10°C ~ +50°C
Supplement
Ambient Temperature Range
Touch
Colors
5C
Indicators
LEDs are an
integral part
of the switch
and are not
available
separately.
(-)
Accessories
(+)
Tilt
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is isolated and requires external power source. Polarity marks are on the switch.
If the source voltage exceeds the rated voltage, a ballast resistor is required.
The resistor value can be calculated by using the formula in the Supplement section.
Single Color LED with 1 Element
Programmable Illuminated PB
C
No Lamp
www.nkkswitches.com
D71
Series LP01
Toggles
Short Body Pushbuttons
Rockers
CAP COLORS
Spot Illuminated Cap
Illuminated Cap
Nonilluminated Cap
Cap Color Available:
Cap Color Available:
Cap Colors Available:
A
White
Pushbuttons
Material: Polycarbonate
Finish: Matte
Spot illuminated, illuminated, and nonilluminated caps are an
integral part of the switch and are not available separately.
A
Black
C
Red
F
Green
TYPICAL SWITCH DIMENSIONS
Bushing Mount Single Pole
3
LP0115CCKW015CB
(2.5)
.098
(13.6) Dia
.535
(20.0) Dia
.787
NC
6
L
–+
2
1
COM
(7.3)
.287
5
(9.7)
.382
4
COM
(3.0)
.118
(5.55)
.219
(6.0)
.236
(11.1)
.437
Single Pole
Rotaries
3
1
(21.3)
.838
(5.5)
.217
L
–+
2
(2.8) Typ
.110
NC
NO
(9.7)
.382
Double Pole
(3.7)
.146
(1.2) x (2.0) Typ
.047 x .079
(3.7)
.146
(0.5) Typ
.020
Double Pole
(3.7)
.146
(1.2) x (2.0) Typ
.047 x .079
M16 P1
4
(6.0)
.236
(11.1)
.437
Single Pole
(3.0) Dia
.118
(9.7)
.382
5
COM
(3.0)
.118
(5.55)
.219
Bushing Mount & Spot Illumination
6
1
COM
(7.3)
.287
NC
L
–+
2
1
(21.3)
.838
(5.5)
.217
3
NO
NO
Slides
LP0115CMKW015CB
(2.5)
.098
(13.6) Dia
.535
(20.0) Dia
.787
L
–+
2
(2.8) Typ
.110
NC
NO
3
NO
(9.7)
.382
(3.7)
.146
Touch
(3.2)
.126
LP0115CCKW015CA
1
6
5
(9.7)
.382
4
COM
(3.0)
.118
(5.55)
.219
Snap-in Mount & Spot Illumination
NC
L
–+
2
COM
(7.3)
.287
(6.0)
.236
(11.1)
.437
Single Pole
(3.0) Dia
.118
3
1
(21.3)
.838
(5.5)
.217
L
–+
2
(2.8) Typ
.110
(2.5)
.098
(13.6) Dia
.535
(20.0) Dia
.787
NC
NO
(9.7)
.382
NO
3
NO
Tilt
(0.5) Typ
.020
NO
Tactiles
(3.7)
.146
(0.5) Typ
.020
Snap-in Mount
Indicators
Double Pole
(3.7)
.146
(1.2) x (2.0) Typ
.047 x .079
M16 P1
NO
D
NO
Programmable Illuminated PB
B
NO
Keylocks
Black with
Spot Illumination
(1.2) x (2.0) Typ
.047 x .079
Double Pole
(3.7)
.146
(3.7)
.146
Supplement
(3.2)
.126
LP0115CMKW015CA
D72
(13.6) Dia
.535
(20.0) Dia
.787
(2.8) Typ
.110
(2.5)
.098
(5.5)
.217
(7.3)
.287
(21.3)
.838
www.nkkswitches.com
NC
L
–+
1
NC
6
L
–+
2
1
COM
(3.0)
.118
(5.55)
.219
3
NO
NO
3
2
5
4
COM
(6.0)
.236
(11.1)
.437
NO
(9.7)
.382
NO
Accessories
(0.5) Typ
.020
(9.7)
.382
Series LP01
Toggles
Short Body Pushbuttons
OPTIONAL ACCESSORIES
NO
– +
(17.0)
.669
(3.0)
.118
AT718
Single Pole
Straight PC
Terminals
(17.1)
.673
NO
L
AT719
Double Pole
Straight PC
Terminals
NO
– +
(17.0)
.669
COM
(3.0)
.118
(4.0)
.157
(3.0) Typ
.118
(17.1)
.673
(4.85) Typ
.191
D
NC
NO
L
(17.0)
.669
COM
(3.0) Typ
.118
(3.7)
.146
(5.55) Typ
.219
(4.0)
.157
(3.7) Typ
.146
(3.7) Typ
.146
(4.85) Typ
.191
(4.85) Typ
.191
(5.55)
.219
Material: Glass fiber reinforced polyamide
CL
(5.55) Typ
.219
Note: Order adaptors separately
Tactiles
CL
(1.0) Dia Typ
.039
(1.85) Typ
.073
(3.0) Typ
.118
(1.0) Dia Typ
.039
(1.85) Typ
.073
(3.0) Typ
.118
NO
– +
(3.7)
.146
(5.55)
.219
NO
(3.7)
.146
(5.55) Typ
.219
NC
(4.85) Typ
.191
L
COM
(5.0)
.197
(3.7)
.146
(5.55)
.219
NC
NO
– +
COM
(5.0)
.197
(4.85) Typ
.191
Pushbuttons
L
Programmable Illuminated PB
NO
Keylocks
NC
(4.85) Typ
.191
(17.1)
.673
Rotaries
(17.0)
.669
AT717
Double Pole
Solder Lug/
Quick Connect
Terminals
Slides
(17.1)
.673
AT716
Single Pole
Solder Lug/
Quick Connect
Terminals
Rockers
Adaptors
Switch Dimensions Shown with Adaptor AT716
Tilt
Dimension A: Solder Lug .197” (5.0mm); Straight PC .157” (4.0mm)
Panel thickness for LP01 Bushing Mount: .079” ~ .256” (2.0mm ~ 6.5mm)
(27.3)
1.075
Touch
A
LEGENDS
Indicators
NKK Switches can provide custom legends for caps. Contact factory for more information.
Recommended Methods:
R
PW
Accessories
Suggested Printable Area for LP01 Cap
Epoxy based ink is recommended.
Note: Suggested printable area does not apply to spot illuminated cap.
www.nkkswitches.com
(12.07) Dia
.475
(13.6) Dia
.535
(0.76) Typ
.030
Supplement
Pad Print or Laser Etch on cap.
Shaded area is printable area
D73
Similar pages