Rohm DTD113EK 500ma / 50v digital transistors (with built-in resistors) Datasheet

DTD113EK / DTD113ES
Transistors
500mA / 50V Digital transistors
(with built-in resistors)
DTD113EK / DTD113ES
zApplications
Inverter, Interface, Driver
zExternal dimensions (Unit : mm)
2.9
DTD113EK
1.1
0.4
zFeatures
1) Built-in bias resistors enable the configuration of an
inverter circuit without connecting external input
resistors (see equivalent circuit).
2) The bias resistors consist of thin-film resistors with
complete isolation to allow negative biasing of the
input. They also have the advantage of almost
completely eliminating parasitic effects.
3) Only the on / off conditions need to be set for
operation, making the device design easy.
1.6
2.8
(3)
(2)
ROHM : SMT3
EIAJ : SC-59
0.15
1.9
Each lead has same dimension
Abbreviated symbol : F21
DTD113ES
2.0
3Min.
(15Min.)
0.45
zPackage specifications
2.5
0.5
0.45
5.0
Package
SMT3
Packaging type
Taping Taping
SPT
Code
T146
TP
Basic ordering unit (pieces)
3000
5000
ROHM : SPT
EIAJ : SC-72
(1) (2) (3)
Abbreviated symbol : D113ES
(1) GND
(2) OUT
(3) IN
−
DTD113EK
−
DTD113ES
zAbsolute maximum ratings (Ta=25°C)
Parameter
(1) GND
(2) IN
(3) OUT
3.0
4.0
0.3Min.
(1)
0.95 0.95
zStructure
NPN epitaxial planar silicon transistor
(Resistor built-in type)
Part No.
0.8
zEquivalent circuit
Limits
Symbol
Unit
DTD113EK DTD113ES
VCC
50
V
Input voltage
VIN
−10 to +10
V
Output current
IC
500
mA
Power dissipation
Pd
Junction temperature
Tj
150
C
Storage temperature
Tstg
−55 to +150
C
200
300
OUT
R1
Supply voltage
IN
R2
GND
mW
OUT
IN
GND
R1=R2=1.0kΩ
Rev.B
1/2
DTD113EK / DTD113ES
Transistors
zElectrical characteristics (Ta=25°C)
Parameter
Input voltage
Output voltage
Input current
Output current
Symbol
Min.
Typ.
Max.
VI(off)
−
−
0.5
Unit
VI(on)
3
−
−
VO(on)
−
0.1
0.3
V
II
−
−
7.2
mA
VI=5V
IO(off)
−
−
0.5
µA
VCC=50V, VI=0V
VO=5V, IO=50mA
V
DC current gain
GI
33
−
−
−
Input resistance
R1
0.7
1
1.3
kΩ
Resistance ratio
R2/R1
0.8
1
1.2
−
−
200
−
MHz
fT ∗
Transition frequency
Conditions
VCC=5V, IO=100µA
VO=0.3V, IO=20mA
IO/II=50mA/2.5mA
−
−
VCE=10V, IE= −50mA, f=100MHz
∗ Characteristics of built-in transistor
zElectrical characteristics curves
10m
VO=0.3V
OUTPUT CURRENT : Io (A)
INPUT VOLTAGE : VI(on) (V)
20
10
5
Ta= −40 C
25 C
100 C
2
1
500m
200m
100m
500µ 1m
2m
1k
VCC=5V
Ta=100 C
25 C
−40 C
5m
50
1m
500µ
200µ
100µ
50µ
20µ
10µ
OUTPUT CURRENT : IO (A)
Fig.1 Input voltage vs. output current
(ON characteristics)
1
100
50
20
10
5
2
1µ
5m 10m 20m 50m100m 200m 500m
Ta=100 C
25 C
−40 C
200
5µ
2µ
2m
VO=5V
500
DC CURRENT GAIN : GI
100
0
0.5
1.0
1.5
2.0
2.5
INPUT VOLTAGE : VI(off) (V)
Fig.2 Output current vs. input voltage
(OFF characteristics)
3.0
1
500µ 1m 2m
5m 10m 20m
50m100m200m 500m
OUTPUT CURRENT : IO (A)
Fig.3 DC current gain
vs. output current
lO/lI=20
OUTPUT VOLTAGE : VO(on) (V)
500m
Ta=100 C
25 C
−40 C
200m
100m
50m
20m
10m
5m
2m
1m
500 µ 1m
2m
5m 10m 20m 50m100m200m 500m
OUTPUT CURRENT : IO (A)
Fig.4 Output voltage vs. output current
Rev.B
2/2
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1
Similar pages