Everlight IRM-V0XX/TR1 Infrared remote-control receiver module Datasheet

EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet
Infrared Remote-control Receiver Module
IRM-V0XX/TR1
Features
‧High shielding against electric field disturbance.
‧Circular lens to improve the receive characteristic.
‧Line-up for various center carrier frequencies.
‧Low voltage and low power consumption.
‧High immunity against ambient light.
‧Photodiode with integrated circuit.
‧TTL and CMOS compatibility.
‧Long reception distance.
‧High sensitivity.
‧Side-received SMD.
‧Suitable burst length ≧10 pulses/burst.
‧This product itself will remain within RoHS compliant version.
‧Pb free.
‧There is no Capacitor between Vcc pin and GND pin on PCB circuit.
Descriptions
The device is a miniature SMD type infrared remote
control system receiver that has been developed and
designed by utilizing the most updated IC technology. The
PIN diode and preamplifier are assembled on PCB, the
epoxy package is designed as an IR filter. The demodulated
output signal can directly be decoded by a microprocessor.
Applications
1. Optical switch
2. Light detecting portion of remote control
․AV instruments such as Audio, TV, VCR, CD, MD, etc.
․Home appliances such as Air-conditioner, Fan , etc.
․The other equipments with wireless remote control.
․CATV set top boxes
Device Selection Guide
PART
MATERIAL
COLOR
Chip
Silicon
---
Package
Epoxy
Black
Metal case
SPCC
Silver white
Plating
Tin
Silver white
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Page: 1 of 12
Document No
Prepared date
Rey 2
:DMO-038-271
:12-12-2007
:
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-V0XX/TR1
Package Dimensions
GND
Vcc
OUT
Notes:
:1.All dimensions are in millimeters.
2.Tolerances unless dimensions ±0.3mm.
Soldering patterns
The following soldering patterns are recommended for reflow-soldering :
Unit: mm
Available Types For Different Carrier Frequencies
Type
Carrier Frequencies (Typ)
IRM-V038/TR1
38 KHz
IRM-V036/TR1
36 KHz
IRM-V040/TR1
40 KHz
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Page: 2 of 12
Document No
Prepared date
Rey 2
:DMO-038-271
:12-12-2007
:
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-V0XX/TR1
Absolute Maximum Ratings (Ta=25℃
℃)
Parameter
Symbol
Rating
Unit
Supply Voltage
Vcc
0~6
V
Operating Temperature
Topr
-25 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +85
℃
Notice
Recommended Operating Condition
Supply Voltage Rating: Vcc 2.7V to 5.5V
Electro-Optical Characteristics (Ta=25℃
℃, and Vcc=3.0V)
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
Condition
Supply Current
Icc
---
---
1.2
mA
No signal input
Peak Wavelength
λp
---
940
---
nm
L0
10
---
---
L45
5
---
---
Half Angle(Horizontal)
Θh
---
45
---
deg
Half Angle(Vertical)
Θv
---
45
---
deg
High Level Pulse Width
TH
400
---
800
μs
Low Level Pulse Width
TL
400
---
800
μs
High Level Output Voltage
VH
2.7
---
---
V
Low Level Output Voltage
VL
---
0.2
0.5
V
Reception Distance
m
At the ray axis
*1
At the ray axis
*2
Notes:
*1:The ray receiving surface at a vertex and relation to the ray axis in the range of θ= 0° and θ=45°.
*2:A range from 30cm to the arrival distance. Average value of 50 pulses.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Page: 3 of 12
Document No
Prepared date
Rey 2
:DMO-038-271
:12-12-2007
:
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-V0XX/TR1
The Notice of Application:
Transmission remote control signal consist of four parts: Encode Part, IR Transmitter Source, IRM
device, Decode Part
1. When IRM-V0xx code select frequency, it need to well understand the center system of
encode part.
2. Strong or weak light of IR Transmitter can affect distance of transmission.
3. Minimum Burst Length Tburst (number of pulses per burst) : 10 cycles
4. It needs to ensure the translation range of decode part if it is applied to the pulse-width range.
If the above items hardly assure of its application, it’ll cause NG(no good) message from the edge of
signal.
Test Method:
:
The specified electro-optical characteristics is satisfied under the following
Conditions at the controllable distance.
Measurement place
A place that is nothing of extreme light reflected in the room.
External light
Project the light of ordinary white fluorescent lamps which are not high
Frequency lamps and must be less then 10 Lux at the module surface.
(Ee≦10Lux)
Standard transmitter
A transmitter whose output is so adjusted as to Vo=400mVp-p and the output
Wave form shown in Fig.-1.According to the measurement method shown in
Fig.-2 the standard transmitter is specified.
However , the infrared photodiode to be used for the transmitter should be
λp=940nm,∆λ=50nm. Also, photodiode is used of PD438B(Vr=5V).
(Standard light / Light source temperature 2856°K).
Measuring system
According to the measuring system shown in Fig.-3
Fig.-1
Transmitter Wave Form
D.U.T output Pulse
Carrier frequency is adjusted to
center frequency of each product.
OUTPUT PULSE
OF DEVICE
IR TANSMITTER
OUTPUT WAVE FORM
Duty=0.5
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Page: 4 of 12
Document No
Prepared date
Rey 2
:DMO-038-271
:12-12-2007
:
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-V0XX/TR1
Fig.-2
Measuring Method
Fig.-3
Measuring System
20cm
10k
+5.0± 0.1V
L: Transmission Distance
θ
θ
10uF
Standard Transmitter
Standard Transmitter
Vout
k
0
10
Vcc
OUT
D.U.T
Vout
GND
θ: Angle Of Horizontal & Vertical Direction
Oscilloscope
Block Diagram:
Vs
IN
OUT
Input
Oscillator
CGA & filter
µC
Demodulator
AGC/ATC & digital control
Carrier frequency f0
Modulated IR signal
min 10 pulses
GND
Application Circuit:
RC Filter should be connected closely between Vcc pin and GND pin.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Page: 5 of 12
Document No
Prepared date
Rey 2
:DMO-038-271
:12-12-2007
:
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-V0XX/TR1
Typical Electro-Optical Characteristics Curves
Fig.-4 Relative Spectral Sensitivity vs.
Wavelength
Fig.-5 Relative Transmission Distance vs.
Direction
θ
Fig.-6 Output Pulse Length vs. Arrival Distance
Fig.-7 Arrival Distance vs. Supply Voltage
12.5
10.0
7.5
5.0
2.5
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Page: 6 of 12
Document No
Prepared date
Rey 2
:DMO-038-271
:12-12-2007
:
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-V0XX/TR1
Typical Electro-Optical Characteristics Curves
Fig.-8 Output Pulse Length vs. Arrival Distance
Fig.-9 Relative Transmission Distance vs. Center
Carrier Frequency
µ
Relative Transmission Distance (%)
IRM-V036/TR1-P
Center Carrier Frequency (kHz)
Fig.-9 Relative Transmission Distance vs. Center Carrier Frequency
IRM-V040/TR1-P
Relative Transmission Distance (%)
Relative Transmission Distance (%)
IRM-V038/TR1-P
Center Carrier Frequency (kHz)
Center Carrier Frequency (kHz)
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Page: 7 of 12
Document No
Prepared date
Rey 2
:DMO-038-271
:12-12-2007
:
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-V0XX/TR1
Reliability Test Item And Condition
The reliability of products shall be satisfied with items listed below.
Confidence level:90%
LTPD:10%
Reflow Terms: JEDEC Level 4 Specification
Drying; Temp.:125℃ 24hrs Moisture 30℃ / 60% RH 96hrs Reflow Temp.: 260℃±5℃
10sec, 3 times
Note:
1. Not sooner than 15 minutes and not longer than 4 hours after removal from the
temperature/humidity chamber.
2. The time between reflow shall be 5 minutes minimum and 60 minutes maximum.
Test Items
Failure Judgement
Test Conditions
Criteria
1 cycle:-40℃
Temperature cycle
Samples(n)
Defective(c)
+85℃
(30min)(5min)(30min)
300 cycle test
Temp:+85℃
High temperature test Vcc:5V
1000hrs
L0≦ L×0.8
L45≦ L×0.8
n=76,c=0
L: Lower
n=76,c=0
specification limit
Low temperature
storage
Temp:-40℃
High temperature
High humidity
Ta:85℃,RH:85%
n=76,c=0
*Icc : Operate
Current (mA)
Variation≦±20%:
1000hrs
n=76,c=0
1000hrs
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Page: 8 of 12
Document No
Prepared date
Rey 2
:DMO-038-271
:12-12-2007
:
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-V0XX/TR1
Recommended method of storage
The following are general recommendations for moisture sensitive level (MSL) 4 storage and use:
Shelf life in sealed bag: 12 months at < 40 °C and < 90% relative humidity (RH)
After bag is opened, devices that will be subjected to reflow solder or other high temperature
process must
a) Mounted within 72 hours of factory conditions < 30 °C/60%RH, or
b) Stored at <20% RH
Devices require bake, before mounting, if:
Humidity Indicator Card is > 20% when read at 23 ± 5 °C
If baking is required, devices may be baked:
a) 192 hours at 40℃,and <5% RH(dry air/nitrogen) or
b) 96 hours at 60℃,and <5% RH for all device containers
c) 24 hours at 125 °C
Soldering Condition
a) Pb-free solder temperature profile
b) Reflow soldering should not be done more than two times.
c) When soldering, do not put stress on the unit during heating.
d) After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Page: 9 of 12
Document No
Prepared date
Rey 2
:DMO-038-271
:12-12-2007
:
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-V0XX/TR1
Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3
seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more
intervals, and do soldering of each terminal. Be careful because the damage of the product is often
started at the time of the hand solder.
Repairing
Repair should not be done after the Devices have been soldered. When repairing is
unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed
beforehand whether the characteristics of the Devices will or will not be damaged by repairing.
ESD Precaution
Proper storage and handing procedures should be followed to prevent ESD damage to
the devices especially when they are removed from the Anti-static bag. Electro-Static Sensitive
Devices warning labels are on the packing.
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Page: 10 of 12
Document No
Prepared date
Rey 2
:DMO-038-271
:12-12-2007
:
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-V0XX/TR1
Packing Quantity Specification
1. 500 PCS/1 Reel
2. 5 Reel /1Carton
Carrier Tape Dimensions: Loaded quantity 500 PCS per reel
Packing process
Bar Code Label
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Page: 11 of 12
Document No
Prepared date
Rey 2
:DMO-038-271
:12-12-2007
:
EVERLIGHT ELECTRONICS CO.,LTD.
IRM-V0XX/TR1
Label Form Specification
Pb
RoHS
CPN: Customer’s Production Number
P/N : Production Number
QTY: Packing Quantity
CAT: None
HUE: None
REF: Reference
LOT No: Lot Number
MADE IN TAIWAN: Production Place
IRM-V0XX/TR1
Notes
1. Above specification may be changed without notice. EVERLIGHT will reserve authority on
material change for above specification.
2. When using this product, please observe the absolute maximum ratings and the instructions
for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for
any damage resulting from use of the product which does not comply with the absolute
maximum ratings and the instructions included in these specification sheets.
3. These specification sheets include materials protected under copyright of EVERLIGHT
corporation. Please don’t reproduce or cause anyone to reproduce them without
EVERLIGHT’s consent.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http:\\www.everlight.com
Everlight Electronics Co., Ltd.
http:\\www.everlight.com
Page: 12 of 12
Document No
Prepared date
Rey 2
:DMO-038-271
:12-12-2007
:
Similar pages