Renesas EL7252CN Dual input, high speed, dual channel power mosfet driver Datasheet

DATASHEET
EL7242, EL7252
Dual Input, High Speed, Dual Channel Power MOSFET Driver
The EL7242/EL7252 dual input, 2-channel drivers achieve
the same excellent switching performance of the EL7212
family while providing added flexibility. The 2-input logic and
configuration is applicable to numerous power MOSFET
drive circuits. As with other Intersil drivers, the
EL7242/EL7252 are excellent for driving large capacitive
loads with minimal delay and switching times. “Shoot-thru”
protection and latching circuits can be implemented by
simply “cross-coupling” the 2-channels.
Pinouts
EL7242
(8 LD PDIP, SOIC)
TOP VIEW
A IN 1
8 V+
B IN 2
7 OUT A
C IN 3
6 OUT B
D IN 4
5 GND
FN7285
Rev 5.00
September 3, 2015
Features
• Logic AND/NAND input
• 3V and 5V Input compatible
• Clocking speeds up to 10MHz
• 20ns Switching/delay time
• 2A Peak drive
• Isolated drains
• Low output impedance
• Low quiescent current
• Wide operating voltage — 4.5V to 16V
• Pb-free available (RoHS compliant)
Applications
• Short circuit protected switching
• Undervoltage shut-down circuits
• Switch-mode power supplies
• Motor controls
EL7252
(8 LD PDIP, SOIC)
TOP VIEW
• Power MOSFET switching
• Switching capacitive loads
A IN 1
8 V+
• Shoot-thru protection
B IN 2
7 OUT A
• Latching drivers
C IN 3
6 OUT B
D IN 4
5 GND
Manufactured under U.S. Patent Nos. 5,334,883, #5,341,047
FN7285 Rev 5.00
September 3, 2015
Page 1 of 9
EL7242, EL7252
Ordering Information
PART NUMBER
PART MARKING
PACKAGE
PKG. DWG. #
EL7242CNZ (Note 1)
EL7242CN Z
8 Ld PDIP** (Pb-free)
E8.3
EL7242CSZ (Note 1)
7242CSZ
8 Ld SOIC (Pb-free)
MDP0027
EL7242CSZ-T7* (Note 1)
7242CSZ
8 Ld SOIC (Pb-free)
MDP0027
EL7242CSZ-T13* (Note 1)
7242CSZ
8 Ld SOIC (Pb-free)
MDP0027
EL7252CSZ (Note 1)
7252CSZ
8 Ld SOIC (Pb-free)
MDP0027
EL7252CSZ-T7* (Note 1)
7252CSZ
8 Ld SOIC (Pb-free)
MDP0027
EL7252CSZ-T13* (Note 1)
7252CSZ
8 Ld SOIC (Pb-free)
MDP0027
EL7252CN (No longer available,
recommended replacement: EL7252CSZ)
EL7252CN
8 Ld PDIP
E8.3
*Please refer to TB347 for details on reel specifications.
**Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
NOTES:
1. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100%
matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations).
Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC
J STD-020.
FN7285 Rev 5.00
September 3, 2015
Page 2 of 9
EL7242, EL7252
Absolute Maximum Ratings (TA = +25°C)
Thermal Information
Supply (V+ to GND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5V
Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.3V above V+
Combined Peak Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . .4A
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Power Dissipation
8 Ld SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .570mW
8 Ld PDIP* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1050mW
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
*Pb-free PDIPs can be used for through hole wave solder
processing only. They are not intended for use in Reflow solder
processing applications.
Operating Conditions
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +125°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
DC Electrical Specifications
PARAMETER
TA = +25°C, V = 15V, unless otherwise specified.
DESCRIPTION
TEST CONDITIONS
MIN
TYP
MAX
UNITS
INPUT
VIH
Logic “1' Input Voltage
IIH
Logic “1' Input Current
VIL
Logic “0' Input Voltage
IIL
Logic “0' Input Current
VHVS
Input Hysteresis
2.4
@V+
V
0.1
@0V
0.1
10
µA
0.8
V
10
µA
0.3
V
OUTPUT
ROH
Pull-up Resistance
IOUT = -100mA
3
6

ROL
Pull-down Resistance
IOUT = +100mA
4
6

IPK
Peak Output Current
Source
2
A
Sink
2
A
IDC
Continuous Output Current
Source/Sink
IS
Power Supply Current
Inputs High
VS
Operating Voltage
100
mA
POWER SUPPLY
AC Electrical Specifications
PARAMETER
1
4.5
2.5
mA
16
V
TA = +25°C, V = 15V, unless otherwise specified.
DESCRIPTION
TEST CONDITIONS
MIN
TYP
MAX
UNITS
CL = 500pF
10
ns
CL = 1000pF
20
ns
CL = 500pF
10
ns
CL = 1000pF
20
ns
SWITCHING CHARACTERISTICS
tR
tF
Rise Time (Note 2)
Fall Time (Note 2)
tD-ON
Turn-On Delay Time (Note 2)
20
25
ns
tD-OFF
Turn-Off Delay Time (Note 2)
20
25
ns
NOTE:
2. Limits established by characterization and are not production tested.
FN7285 Rev 5.00
September 3, 2015
Page 3 of 9
EL7242, EL7252
Timing Table
5V
INPUT 2.5V
0
INVERTED
OUTPUT
NON-INVERTED
OUTPUT
90%
10%
90%
10%
tD1
tF
tR
tD2
tR
tF
Standard Test Configuration
V+
3
4
4.7µF
TAN
EL7242
1
2
7
OUTPUT
1000pF
LOAD
INPUT
5
Simplified Schematic
V+
OUTPUT
+
-
INPUT
+
INPUT
BUFFER
FN7285 Rev 5.00
September 3, 2015
VREF
REFERENCE AND
LEVEL SHIFTER
INVERTING
BUFFER
WITH
HYSTERESIS
LOGIC
GATE
SUPER INVERTER
Page 4 of 9
EL7242, EL7252
Typical Performance Curves
2.0
PDIP8
1.05W
JA = 95°C/W
0.8
MAX TJ= 125°C
570mW
0.6
0.4
SO8
0.2
0.0
HIGH LIMIT = 2.4V
1.8
1.6
INPUT VOLTAGE
POWER DISSIPATION (W)
1.0
HYSTERESIS
1.4
1.2
1.0
LOW LIMIT = 0.8V
JA = 175°C/W
0
25
50
75
100
125
AMBIENT TEMPERATURE (°C)
0.0
150
FIGURE 1. MAX POWER/DERATING CURVES
0
5
10
SUPPLY VOLTAGE
15
FIGURE 2. SWITCH THRESHOLD vs SUPPLY VOLTAGE
V - SUPPLY
0
15
10
5
0
10
N-CHANNEL
SINK (A)
2/DIV
0
-1
1
P-CHANNEL
-2
-10
-5
0
V+
20
0
5
FIGURE 3. INPUT CURRENT vs VOLTAGE
B
6
5
C
CASE:
A ALL INPUTS GND
B 3 INPUTS GND
C 2 INPUTS GND
4
3
D
2
1
MEASURED AT
100mA
8
D 1 INPUT GND
E ALL INPUTS V+
ON-RESISTANCE ()
SUPPLY CURRENT (mA)
7
15
FIGURE 4. PEAK DRIVE vs SUPPLY VOLTAGE
A
8
10
V - SUPPLY
VIN 2.5V/DIV
PULL-DOWN
6
4
2
PULL-UP
E
0
0
5
10
15
SUPPLY VOLTAGE (V)
FIGURE 5. QUIESCENT SUPPLY CURRENT
FN7285 Rev 5.00
September 3, 2015
0
5
10
15
SUPPLY VOLTAGE (V)
FIGURE 6. ON-RESISTANCE vs SUPPLY VOLTAGE
Page 5 of 9
SOURCE (A)
IIN (mA)
2
EL7242, EL7252
Typical Performance Curves
(Continued)
100
VDD = +15V
VDD = +10V
10
VDD = +5V
1
CL = 1000pF
0.1
10k
100k
1000pF
10,000pF
1M
SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
100
10
100pF
1
NO LOAD
VDD = 10V
(EQUIVALENT INTERNAL
CAPACITANCE = 470pF)
0.1
10k
10M
100k
FREQUENCY (Hz)
FIGURE 7. AVERAGE SUPPLY CURRENT vs VOLTAGE AND
FREQUENCY
30
VDD = 10V
80
60
40
tF
20
20
tF
10
tR
tR
100
1000
CL = 1000pF
0
10,000
5
7.5
10
12.5
SUPPLY VOLTAGE (V)
LOAD CAPACITANCE (pF)
FIGURE 9. RISE/FALL TIME vs LOAD
30
tD2
30
RISE/FALL TIME (ns)
DELAY TIME (ns)
15
FIGURE 10. RISE/FALL TIME vs SUPPLY VOLTAGE
40
20
tD1
10
0
10M
FIGURE 8. AVERAGE SUPPLY CURRENT vs CAPACITIVE
LOAD
RISE/FALL TIME (ns)
RISE/FALL TIME (ns)
100
1M
FREQUENCY (Hz)
CL = 1000pF
5
7.5
10
12.5
15
SUPPLY VOLTAGE (V)
FIGURE 11. PROPAGATION DELAY vs SUPPLY VOLTAGE
FN7285 Rev 5.00
September 3, 2015
20
tF
10
VDD = 10V
0
-50
tR
CL = 1000pF
-25
0
25
50
75
100
125
TEMPERATURE (°C)
FIGURE 12. RISE/FALL TIME vs TEMPERATURE
Page 6 of 9
EL7242, EL7252
Typical Performance Curves
(Continued)
40
tD2
DELAY TIME (ns)
30
20
tD1
10
0
-50
VDD = 10V
CL = 1000pF
-25
0
25
50
75
100
125
TEMPERATURE (°C)
FIGURE 13. DELAY vs TEMPERATURE
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that
you have the latest revision.
DATE
REVISION
September 3, 2015
FN7285.5
CHANGE
Updated Ordering Information Table on page 2.
Added Revision History and About Intersil sections.
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support
FN7285 Rev 5.00
September 3, 2015
Page 7 of 9
EL7242, EL7252
Small Outline Package Family (SO)
A
D
h X 45°
(N/2)+1
N
A
PIN #1
I.D. MARK
E1
E
c
SEE DETAIL “X”
1
(N/2)
B
L1
0.010 M C A B
e
H
C
A2
GAUGE
PLANE
SEATING
PLANE
A1
0.004 C
0.010 M C A B
L
b
0.010
4° ±4°
DETAIL X
MDP0027
SMALL OUTLINE PACKAGE FAMILY (SO)
INCHES
SYMBOL
SO-14
SO16 (0.300”)
(SOL-16)
SO20
(SOL-20)
SO24
(SOL-24)
SO28
(SOL-28)
TOLERANCE
NOTES
A
0.068
0.068
0.068
0.104
0.104
0.104
0.104
MAX
-
A1
0.006
0.006
0.006
0.007
0.007
0.007
0.007
0.003
-
A2
0.057
0.057
0.057
0.092
0.092
0.092
0.092
0.002
-
b
0.017
0.017
0.017
0.017
0.017
0.017
0.017
0.003
-
c
0.009
0.009
0.009
0.011
0.011
0.011
0.011
0.001
-
D
0.193
0.341
0.390
0.406
0.504
0.606
0.704
0.004
1, 3
E
0.236
0.236
0.236
0.406
0.406
0.406
0.406
0.008
-
E1
0.154
0.154
0.154
0.295
0.295
0.295
0.295
0.004
2, 3
e
0.050
0.050
0.050
0.050
0.050
0.050
0.050
Basic
-
L
0.025
0.025
0.025
0.030
0.030
0.030
0.030
0.009
-
L1
0.041
0.041
0.041
0.056
0.056
0.056
0.056
Basic
-
h
0.013
0.013
0.013
0.020
0.020
0.020
0.020
Reference
-
16
20
24
28
Reference
-
N
SO-8
SO16
(0.150”)
8
14
16
NOTES:
Rev. M 2/07
1. Plastic or metal protrusions of 0.006” maximum per side are not included.
2. Plastic interlead protrusions of 0.010” maximum per side are not included.
3. Dimensions “D” and “E1” are measured at Datum Plane “H”.
4. Dimensioning and tolerancing per ASME Y14.5M-1994
FN7285 Rev 5.00
September 3, 2015
Page 8 of 9
EL7242, EL7252
Dual-In-Line Plastic Packages (PDIP)
E8.3 (JEDEC MS-001-BA ISSUE D)
N
8 LEAD DUAL-IN-LINE PLASTIC PACKAGE
E1
INDEX
AREA
1 2 3
INCHES
N/2
-B-
-AD
E
BASE
PLANE
-C-
SEATING
PLANE
A2
A
L
D1
e
B1
D1
A1
eC
B
0.010 (0.25) M
C A B S
MILLIMETERS
SYMBOL
MIN
MAX
MIN
MAX
NOTES
A
-
0.210
-
5.33
4
A1
0.015
-
0.39
-
4
A2
0.115
0.195
2.93
4.95
-
B
0.014
0.022
0.356
0.558
-
C
L
B1
0.045
0.070
1.15
1.77
8, 10
eA
C
0.008
0.014
0.204
C
D
0.355
0.400
9.01
eB
NOTES:
1. Controlling Dimensions: INCH. In case of conflict between
English and Metric dimensions, the inch dimensions control.
5
D1
0.005
-
0.13
-
5
E
0.300
0.325
7.62
8.25
6
E1
0.240
0.280
6.10
7.11
5
e
0.100 BSC
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
eA
0.300 BSC
3. Symbols are defined in the “MO Series Symbol List” in Section
2.2 of Publication No. 95.
eB
-
L
0.115
4. Dimensions A, A1 and L are measured with the package seated
in JEDEC seating plane gauge GS-3.
0.355
10.16
N
2.54 BSC
7.62 BSC
0.430
-
0.150
2.93
8
5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch
(0.25mm).
6. E and eA are measured with the leads constrained to be perpendicular to datum -C- .
8
6
10.92
7
3.81
4
9
Rev. 0 12/93
7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater.
8. B1 maximum dimensions do not include dambar protrusions.
Dambar protrusions shall not exceed 0.010 inch (0.25mm).
9. N is the maximum number of terminal positions.
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3,
E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch
(0.76 - 1.14mm).
© Copyright Intersil Americas LLC 2003-2015. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN7285 Rev 5.00
September 3, 2015
Page 9 of 9
Similar pages