DBLECTRO BTP3-99YECG-B5-X/W

ProLite 3W SMD Emitter
BTP3-99XXCG-XX-X/W
Package Dimension
Features
Highest Lumen Per Watt
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Long Operational Life
White Housing
Superior ESD Protection
Instant Light (less than 100ns)
Compatible to Luxeon’s “Lambertian”
True SMD Emitter
IR Reflow Soldering Process
Applications
Accent Light/Down Light/Spot Light
Automotive Exterior/Interior Light
Large Area LCD Backlights
Marine/Miner’s Lighting
Portable Flashlight/ General Lighting
ƒ
ƒ
ƒ
ƒ
ƒ
Note: Lens is low dome profile
Tolerance:
± see spec
Unit: mm
Optical Characteristics at TJ=25ºC, IF=700mA
PART NUMBER
Emitting
Color
LED Chip
Material
Lens
Color
Wavelength (nm)
CCT (K) Range
Drive
Luminous
VIEW
Voltage
Flux (lm)
ANGLE
@ 700mA
@700mA
2θ1/2
Typ.
(deg)
Min
Max
Typ.
Water Clear
620
635
2.40V
60 lm
Water Clear
610
620
2.40V
72 lm
BTP3-99NRCG-XX-X/W
Normal Red
BTP3-99AMCG-XX-X/W
Amber
BTP3-99YECG-XX-X/W
Yellow
Water Clear
585
595
2.40V
60 lm
BTP3-99BLCG-XX-X/W
Blue
Water Clear
460
475
3.50V
20 lm
BTP3-99PGCG-XX-X/W
Green
Water Clear
520
540
3.50V
60 lm
Water Clear
2800K
3800K
3.50V
40 lm
Water Clear
5000K
8000K
3.50V
60 lm
BTP3-99WWCG-XX-X/W Warm White
BTP3-99WHCG-XX-X/W
White
AlInGaP
AlInGaN
140
Notes:
1)
Picture for illustration purpose only.
Please refer to outline dimension for actual package size.
2)
Flux is measured with the accuracy of ±15%. Please refer to Flux Selection Guide
3)
CCT is measured with the accuracy of ± 400K. Please refer to CCT Selection Guide
4)
VF is measured with the accuracy of ± 0.15V. Please refer to VF Selection Guide
Part No.: BTP3-99XXCG-XX-X/W
Rev1.2005
Page 1 of 10
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com
ProLite 3W SMD Emitter
BTP3-99XXCG-XX-X/W
Absolute Maximum Ratings at TJ=25ºC
Parameter
Red/Amber/Yellow
White/Blue/Green
2.17
2.80
700
700
1000
1000
Average Forward Current (mA)
700
700
Reverse Voltage (V)
5
5
Reverse Current (uA)
50
50
16,000
16,000
120
135
Thermal Resistance Junction to Board (°C/W)
13
13
Temperature Coefficient of VF (mV/°C)
-2
-2
Storage Temperature (°C)
-40 to +105
-40 to +105
Operating Temperature (°C)
-40 to +105
-40 to +105
Power Dissipation (W)
[1]
DC Forward Current (mA)
Peak Pulsed Forward Current (mA)
[4]
ESD Sensitivity (V) [2]
LED Junction Temperature at 350mA (°C)
[3]
Lead Soldering Temperature (°C)[4]
260°C for 5 seconds max 260°C for 5 seconds max
Application Notes:
1.
Proper forward current must be observed to maintain the junction temperature below maximum
rating
2.
Although all products listed are class one ESD protection (+/- 16KV by HBM mode), care must be
fully taken when handling products
3.
Specification is subjected to change for improvements without notice.
4.
Test conditions: tp≤10us, duty cycle = 0.005
5.
CAUTION: When lighting up, the emitter will become very hot if it is not attached to a heat sink.
Please provide proper heat management to prevent damage to the emitter.
Part No.: BTP3-99XXCG-XX-X/W
Rev1.2005
Page 2 of 10
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com
ProLite 3W SMD Emitter
BTP3-99XXCG-XX-X/W
CCT, Flux and VF Selection Guide (@TJ=25ºC, IF=700mA)
BTP3-99XXCG-XX-X/W
White Housing
Wavelength Ranks Selection
Color
Blue
Green
Red
Amber
Yellow
Bin
B5
B6
B7
XX
G6
G7
G8
G9
XX
XX
XX
XX
Flux Ranks Selection
λD(nm)
Min
Max
460
465
465
470
470
475
460 – 475
515
520
520
525
525
530
530
535
515 – 535
620 – 630
610 – 620
585 – 595
CCT Ranks Selection
Color
Temp
Warm
White
White
Bin
00
01
XX
02
03
04
XX
Color
Blue
Red
Amber
Yellow
Green
White
Bin
Flux (lumens)
K
8~10
L
10~14
M
14~18
X
Default Full Range
Q
30~39
R
39~50
S
50~65
T
65~85
U
85~111
X
Default Full Range
VF Ranks Selection
CCT(K)
Min
Max
2800
3300
3300
3800
2800K – 3800K
5000
6000
6000
7000
7000
8000
5000K – 8000K
Color
Red
Amber
Yellow
White
Blue
Green
Bin
VF (V)
Min
Max
V04
V05
V06
V07
VXX(Full)
V08
V09
V10
V11
V12
VXX(Full)
2.0
2.2
2.2
2.4
2.4
2.6
2.6
2.8
2.0~2.8
2.8
3.0
3.0
3.2
3.2
3.4
3.4
3.6
3.6
3.8
2.8~3.8
(Please specify on order, otherwise, default full range of VF)
Part No.: BTP3-99XXCG-XX-X/W
Rev1.2005
Page 3 of 10
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com
ProLite 3W SMD Emitter
BTP3-99XXCG-XX-X/W
Typical Electro-Optical Characteristics Curves
Fig. 1 Forward Current vs Ambient Temperature (Green, Blue and White)
Fig. 2 Forward Current vs Ambient Temperature (Red, Amber and Yellow)
Part No.: BTP3-99XXCG-XX-X/W
Rev1.2005
Page 4 of 10
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com
ProLite 3W SMD Emitter
BTP3-99XXCG-XX-X/W
Part No.: BTP3-99XXCG-XX-X/W
Rev1.2005
Page 5 of 10
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com
ProLite 3W SMD Emitter
BTP3-99XXCG-XX-X/W
Typical Electro-Optical Characteristics Curves
Fig. 5a Relative Light Output vs Junction Temperature
Fig. 5b Relative Light Output vs Junction Temperature
Part No.: BTP3-99XXCG-XX-X/W
Rev1.2005
Page 6 of 10
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com
ProLite 3W SMD Emitter
BTP3-99XXCG-XX-X/W
Relative Intensity(%)
Typical Electro-Optical Characteristics Curves
100
90
80
70
60
50
40
30
20
10
0
-100
-80
-60
-40
-20
0
20
40
60
80
100
Angular Displacement(Degree)
Fig. 6 Typical Radiation Pattern
Recommended Solder Pad Layout
Fig. 7 Recommended Solder Pads Dimension
Part No.: BTP3-99XXCG-XX-X/W
Rev1.2005
Page 7 of 10
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com
ProLite 3W SMD Emitter
BTP3-99XXCG-XX-X/W
Tape and Reel Packaging Dimension
Part No.: BTP3-99XXCG-XX-X/W
Rev1.2005
Page 8 of 10
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com
ProLite 3W SMD Emitter
BTP3-99XXCG-XX-X/W
Recommended IR Reflow Conditions
Reflow Soldering
Lead Solder
Pre-heat
Pre-heat time
Peak
Temperature
Soldering Time
Conditions
Lead-Free Solder
120~150ºC
120 sec Max
180~200ºC
120 sec Max
240ºC Max
260ºC Max
10 sec Max
10 sec Max
Refer to Temperature
profile B
(N2 reflow is
recommended)
Refer to
Temperature profile
A
Temperature Profile A (Surface of MCPCB)
Temperature Profile B (Surface of MCPCB)
Part No.: BTP3-99XXCG-XX-X/W
Rev1.2005
Page 9 of 10
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com
ProLite 3W SMD Emitter
BTP3-99XXCG-XX-X/W
IR Reflow Process Notes
z
Occasionally there is a brightness decrease due to the influence of heat or ambient during air
reflow. It is recommended that customer use nitrogen reflow method.
z
Repairing should not be done after the LEDs have been soldered. When repairing is required,
double-head soldering iron should be used. Customer should confirm whether the
characteristics of the LEDs will or will not damaged before carrying out the repair.
z
Reflow soldering should not be done more than two times
z
When soldering, do not put stress on the LEDs during heating.
z
After soldering, do not warp the circuit board.
Manual Hand Soldering Notes
z
For prototype builds or small production runs, it is possible to place and solder the emitters.
z
It is recommended to hand solder the leads and slug with a solder tip temperature of 230ºC for
less than 10seconds. This profile ensures a junction temperature below the maximum of 120ºC,
avoiding damage to the emitter or to the MCPCB dielectric layer. Damage dielectric layer can
cause a short circuit in the array.
Other Important Notes:
z
The information contained herein is presented only as a Guide for the application of our
products. Brilliance Technologies assumes no responsibility for any infringement of intellectual
property or other rights of the third parties which may result from its use.
z
Brilliance Technologies continually improves the quality of our products. Nevertheless,
semiconductor devices in general can malfunction or fail due to their inherent electrical
sensitivity and vulnerability to physical stress.
It is the responsible of the customer, when
using Brilliance Technologies products, to comply with the standard of safety in making a safe
design for the entire system, and to avoid situations in which a malfunction or failure of such
Brilliance Technologies products cause loss of human life, bodily injury or damage to property.
z
Brilliance Technologies products listed in this data sheet are intended for usage in general
electronics and/or non-commercial or industrial lighting products. These products are neither
intended nor warranted for usage in equipment that requires extraordinarily high quality and/or
reliability or a malfunction or failure of which may cause loss of human life or bodily injury.
z
In developing your design, please ensure that Brilliance Technologies products are used within
specified operating ranges as set forth in the most recent Brilliance Technologies data sheets.
BT-Rev. 1.0A20050119
Specifications are subject to change for improvement without notice.
Copyright © 2003 Brilliance Technologies Co., Ltd. All rights reserved.
Part No.: BTP3-99XXCG-XX-X/W
Rev1.2005
Page 10 of 10
DB LECTRO Inc. 3600 boul. Matte suite i Brossard Qc J4Y-2Z2 tel:(450)-444-1424 fax:(450)-444-4714 www.dblectro.com