MOTOROLA MTP60N05HDL

Order this document
by MTP60N05HDL/D
SEMICONDUCTOR TECHNICAL DATA

Motorola Preferred Device
N–Channel Enhancement–Mode Silicon Gate
TMOS POWER FET
60 AMPERES
50 VOLTS
RDS(on) = 0.014 OHM
This advanced high–cell density HDTMOS power FET is
designed to withstand high energy in the avalanche and commutation modes. The new energy efficient design also offers a
drain–to–source diode with a fast recovery time. Designed for low
voltage, high speed switching applications in power supplies,
converters and PWM motor controls, these devices are particularly
well suited for bridge circuits where diode speed and commutating
safe operating areas are critical and offer additional safety margin
against unexpected voltage transients.

• Avalanche Energy Specified
• Source–to–Drain Diode Recovery Time Comparable to a Discrete Fast Recovery Diode
• Diode is Characterized for Use in Bridge Circuits
• IDSS and VDS(on) Specified at Elevated Temperature
D
G
CASE 221A–06, Style 5
TO–220AB
S
MAXIMUM RATINGS (TC = 25°C unless otherwise noted)
Rating
Symbol
Value
Unit
Drain–to–Source Voltage
VDSS
50
Vdc
Drain–to–Gate Voltage (RGS = 1.0 MΩ)
VDGR
50
Vdc
Gate–to–Source Voltage — Continuous
— Non–Repetitive (tp ≤ 10 ms)
VGS
VGSM
± 15
± 20
Vdc
Vpk
Drain Current — Continuous
— Continuous @ 100°C
— Single Pulse (tp ≤ 10 µs)
ID
ID
IDM
60
42
180
Adc
Total Power Dissipation
Derate above 25°C
PD
150
1.0
Watts
W/°C
TJ, Tstg
– 55 to 175
°C
Single Pulse Drain–to–Source Avalanche Energy — Starting TJ = 25°C
(VDD = 25 Vdc, VGS = 10 Vdc, Peak IL = 60 Apk, L = 0.3 mH, RG = 25 Ω)
EAS
540
mJ
Thermal Resistance — Junction to Case
— Junction to Ambient
RθJC
RθJA
1.0
62.5
°C/W
TL
260
°C
Operating and Storage Temperature Range
Maximum Lead Temperature for Soldering Purposes, 1/8″ from Case for 5 Seconds
Apk
E–FET and HDTMOS are trademarks of Motorola, Inc. TMOS is a registered trademark of Motorola, Inc.
This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice.
Preferred devices are Motorola recommended choices for future use and best overall value.
TMOS
Motorola
Motorola, Inc.
1997 Power MOSFET Transistor Device Data
1
MTP60N05HDL
ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted)
Characteristic
Symbol
Min
Typ
Max
50
—
—
55
—
—
—
—
—
—
10
100
—
—
100
1.0
—
1.5
4.5
2.0
—
—
0.010
0.014
—
—
—
—
1.0
0.75
15
48
—
Unit
OFF CHARACTERISTICS
Drain–to–Source Breakdown Voltage
(VGS = 0 Vdc, ID = 0.25 mAdc)
Temperature Coefficient (Positive)
V(BR)DSS
Zero Gate Voltage Drain Current
(VDS = 50 Vdc, VGS = 0 Vdc)
(VDS = 50 Vdc, VGS = 0 Vdc, TJ = –25°C)
IDSS
Gate–Body Leakage Current
(VGS = ± 15 Vdc, VDS = 0 Vdc)
IGSS
Vdc
mV/°C
µAdc
nAdc
ON CHARACTERISTICS (1)
Gate Threshold Voltage
(VDS = VGS, ID = 250 µAdc)
Threshold Temperature Coefficient (Negative)
VGS(th)
Static Drain–to–Source On–Resistance
(VGS = 5.0 Vdc, ID = 30 Adc)
RDS(on)
Drain–to–Source On–Voltage (VGS = 5.0 Vdc)
(ID = 60 Adc)
(ID = 30 Adc, TJ = 125°C)
VDS(on)
Forward Transconductance
(VDS = 4.0 Vdc, ID = 20 Adc)
Vdc
mV/°C
Ohms
Vdc
gFS
mhos
DYNAMIC CHARACTERISTICS
Input Capacitance
Output Capacitance
(VDS = 25 Vdc,
Vdc VGS = 0 Vdc,
Vdc
f = 1.0 MHz)
Transfer Capacitance
Ciss
—
2775
4000
Coss
—
750
1070
Crss
—
150
300
td(on)
—
21
40
pF
SWITCHING CHARACTERISTICS (2)
Turn–On Delay Time
Rise Time
Turn–Off Delay Time
( DD = 25 Vdc,
(V
Vd , ID = 60 Adc,
Ad ,
VGS = 5.0 Vdc, RG = 9.1 Ω)
Fall Time
Gate Charge
( DD = 25 Vdc,
(V
Vd , ID = 60 Adc,
Ad ,
VGS = 5.0 Vdc, RG = 9.1 W)
tr
—
570
1150
td(off)
—
86
170
tf
—
200
400
QT
—
42
62
Q1
—
8.0
—
Q2
—
24
—
Q3
—
17
—
—
—
0.95
0.85
1.1
—
trr
—
50
—
ta
—
34
—
tb
—
15
—
QRR
—
0.085
—
ns
nC
SOURCE–DRAIN DIODE CHARACTERISTICS
Forward On–Voltage
VSD
(IS = 60 Adc, VGS = 0 Vdc)
(IS = 60 Adc, VGS = 0 Vdc, TJ = 125°C)
Reverse Recovery Time
((IS = 30 Adc,
Ad , VGS = 0 Vdc,
Vd ,
dIS/dt = 100 A/µs)
Reverse Recovery Stored Charge
Vdc
ns
µC
(1) Pulse Test: Pulse Width ≤ 300 µs, Duty Cycle ≤ 2%.
(2) Switching characteristics are independent of operating junction temperature.
2
Motorola TMOS Power MOSFET Transistor Device Data
MTP60N05HDL
TYPICAL ELECTRICAL CHARACTERISTICS
120
4.5 V
VGS = 10 V
VDS ≥ 10 V
TJ = 25°C
8.0 V
6.0 V
80
3.5 V
5.0 V
60
40
100
ID , DRAIN CURRENT (AMPS)
ID , DRAIN CURRENT (AMPS)
100
120
4.0 V
3.0 V
20
80
60
40
TJ = 125°C
2.5 V
–55°C
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
2.0
2.5
3.0
3.5
VGS, GATE–TO–SOURCE VOLTAGE (VOLTS)
Figure 1. On–Region Characteristics
Figure 2. Transfer Characteristics
0.016
TJ = 100°C
0.014
0.012
25°C
0.010
0.008
–55°C
0.006
10
0
1.5
5.0
VDS, DRAIN–TO–SOURCE VOLTAGE (VOLTS)
20
30
50
40
60
70
80
90
100 110 120
R DS(on) , DRAIN–TO–SOURCE RESISTANCE (OHMS)
0
0.018
4.0
0.014
0.013
TJ = 25°C
0.012
0.011
VGS = 5.0 V
0.010
10 V
0.009
0.008
0.007
0.006
0
20
40
60
80
100
120
ID, DRAIN CURRENT (AMPS)
ID, DRAIN CURRENT (AMPS)
Figure 3. On–Resistance versus Drain Current
and Temperature
Figure 4. On–Resistance versus Drain Current
and Gate Voltage
10,000
1.8
1.6
VGS = 0 V
VGS = 10 V
ID = 5.0 A
TJ = 125°C
1000
IDSS, LEAKAGE (nA)
RDS(on) , DRAIN–TO–SOURCE RESISTANCE
(NORMALIZED)
RDS(on) , DRAIN–TO–SOURCE RESISTANCE (OHMS)
0
25°C
20
1.4
1.2
1.0
100°C
100
10
0.8
25°C
0.6
– 50
1.0
– 25
0
25
50
75
100
125
150
5.0
10
15
20
25
30
35
40
TJ, JUNCTION TEMPERATURE (°C)
VDS, DRAIN–TO–SOURCE VOLTAGE (VOLTS)
Figure 5. On–Resistance Variation with
Temperature
Figure 6. Drain–To–Source Leakage
Current versus Voltage
Motorola TMOS Power MOSFET Transistor Device Data
45
50
3
MTP60N05HDL
POWER MOSFET SWITCHING
Switching behavior is most easily modeled and predicted
by recognizing that the power MOSFET is charge controlled.
The lengths of various switching intervals (∆t) are determined by how fast the FET input capacitance can be charged
by current from the generator.
The capacitance (Ciss) is read from the capacitance curve at
a voltage corresponding to the off–state condition when calculating td(on) and is read at a voltage corresponding to the
on–state when calculating td(off).
The published capacitance data is difficult to use for calculating rise and fall because drain–gate capacitance varies
greatly with applied voltage. Accordingly, gate charge data is
used. In most cases, a satisfactory estimate of average input
current (IG(AV)) can be made from a rudimentary analysis of
the drive circuit so that
At high switching speeds, parasitic circuit elements complicate the analysis. The inductance of the MOSFET source
lead, inside the package and in the circuit wiring which is
common to both the drain and gate current paths, produces a
voltage at the source which reduces the gate drive current.
The voltage is determined by Ldi/dt, but since di/dt is a function of drain current, the mathematical solution is complex.
The MOSFET output capacitance also complicates the
mathematics. And finally, MOSFETs have finite internal gate
resistance which effectively adds to the resistance of the
driving source, but the internal resistance is difficult to measure and, consequently, is not specified.
The resistive switching time variation versus gate resistance (Figure 9) shows how typical switching performance is
affected by the parasitic circuit elements. If the parasitics
were not present, the slope of the curves would maintain a
value of unity regardless of the switching speed. The circuit
used to obtain the data is constructed to minimize common
inductance in the drain and gate circuit loops and is believed
readily achievable with board mounted components. Most
power electronic loads are inductive; the data in the figure is
taken with a resistive load, which approximates an optimally
snubbed inductive load. Power MOSFETs may be safely operated into an inductive load; however, snubbing reduces
switching losses.
t = Q/IG(AV)
During the rise and fall time interval when switching a resistive load, VGS remains virtually constant at a level known as
the plateau voltage, VSGP. Therefore, rise and fall times may
be approximated by the following:
tr = Q2 x RG/(VGG – VGSP)
tf = Q2 x RG/VGSP
where
VGG = the gate drive voltage, which varies from zero to VGG
RG = the gate drive resistance
and Q2 and VGSP are read from the gate charge curve.
During the turn–on and turn–off delay times, gate current is
not constant. The simplest calculation uses appropriate values from the capacitance curves in a standard equation for
voltage change in an RC network. The equations are:
td(on) = RG Ciss In [VGG/(VGG – VGSP)]
td(off) = RG Ciss In (VGG/VGSP)
10,000
VDS = 0 VGS = 0
9000
8000
C, CAPACITANCE (pF)
TJ = 25°C
Ciss
7000
Crss
6000
5000
4000
Ciss
3000
2000
1000
0
–10
Coss
Crss
–5.0
0
VGS
5.0
10
15
20
25
VDS
GATE–TO–SOURCE OR DRAIN–TO–SOURCE VOLTAGE (VOLTS)
Figure 7. Capacitance Variation
4
Motorola TMOS Power MOSFET Transistor Device Data
60
50
VGS
6.0
QT
40
4.0
30
Q1
2.0
Q2
20
TJ = 60°C
ID = 5.0 A
Q3
10
VDS
0
0
10
20
0
30
40
50
1000
VDD = 25 V
ID = 60 A
VGS = 5.0 V
TJ = 25°C
t, TIME (ns)
8.0
V DS , DRAIN–TO–SOURCE VOLTAGE (VOLTS)
VGS, GATE–TO–SOURCE VOLTAGE (VOLTS)
MTP60N05HDL
tr
tf
td(off)
100
10
td(on)
1.0
10
QG, TOTAL GATE CHARGE (nC)
RG, GATE RESISTANCE (OHMS)
Figure 8. Gate–To–Source and Drain–To–Source
Voltage versus Total Charge
Figure 9. Resistive Switching Time
Variation versus Gate Resistance
100
DRAIN–TO–SOURCE DIODE CHARACTERISTICS
The switching characteristics of a MOSFET body diode
are very important in systems using it as a freewheeling or
commutating diode. Of particular interest are the reverse recovery characteristics which play a major role in determining
switching losses, radiated noise, EMI and RFI.
System switching losses are largely due to the nature of
the body diode itself. The body diode is a minority carrier device, therefore it has a finite reverse recovery time, trr, due to
the storage of minority carrier charge, QRR, as shown in the
typical reverse recovery wave form of Figure 11. It is this
stored charge that, when cleared from the diode, passes
through a potential and defines an energy loss. Obviously,
repeatedly forcing the diode through reverse recovery further
increases switching losses. Therefore, one would like a
diode with short trr and low QRR specifications to minimize
these losses.
The abruptness of diode reverse recovery effects the
amount of radiated noise, voltage spikes, and current ringing. The mechanisms at work are finite irremovable circuit
parasitic inductances and capacitances acted upon by high
di/dts. The diode’s negative di/dt during ta is directly controlled by the device clearing the stored charge. However,
the positive di/dt during tb is an uncontrollable diode characteristic and is usually the culprit that induces current ringing.
Therefore, when comparing diodes, the ratio of tb/ta serves
as a good indicator of recovery abruptness and thus gives a
comparative estimate of probable noise generated. A ratio of
1 is considered ideal and values less than 0.5 are considered
snappy.
Compared to Motorola standard cell density low voltage
MOSFETs, high cell density MOSFET diodes are faster
(shorter trr), have less stored charge and a softer reverse recovery characteristic. The softness advantage of the high
cell density diode means they can be forced through reverse
recovery at a higher di/dt than a standard cell MOSFET
diode without increasing the current ringing or the noise generated. In addition, power dissipation incurred from switching
the diode will be less due to the shorter recovery time and
lower switching losses.
I S, SOURCE CURRENT (AMPS)
60
50
VGS = 0 V
TJ = 25°C
40
30
20
10
0
0.5
0.6
0.7
0.8
0.9
1.0
VSD, SOURCE–TO–DRAIN VOLTAGE (VOLTS)
Figure 10. Diode Forward Voltage versus Current
Motorola TMOS Power MOSFET Transistor Device Data
5
MTP60N05HDL
Standard Cell Density
trr
I S , SOURCE CURRENT
High Cell Density
trr
tb
ta
t, TIME
Figure 11. Reverse Recovery Time (trr)
SAFE OPERATING AREA
The Forward Biased Safe Operating Area curves define
the maximum simultaneous drain–to–source voltage and
drain current that a transistor can handle safely when it is forward biased. Curves are based upon maximum peak junction temperature and a case temperature (TC) of 25°C. Peak
repetitive pulsed power limits are determined by using the
thermal response data in conjunction with the procedures
discussed in AN569, “Transient Thermal Resistance –
General Data and Its Use.”
Switching between the off–state and the on–state may traverse any load line provided neither rated peak current (IDM)
nor rated voltage (VDSS) is exceeded, and that the transition
time (tr, tf) does not exceed 10 µs. In addition the total power
averaged over a complete switching cycle must not exceed
(TJ(MAX) – TC)/(RθJC).
A power MOSFET designated E–FET can be safely used
in switching circuits with unclamped inductive loads. For reli-
EAS, SINGLE PULSE DRAIN–TO–SOURCE
AVALANCHE ENERGY (mJ)
ID, DRAIN CURRENT (AMPS)
1000
VGS = 5.0 V
SINGLE PULSE
TC = 25°C
100
1.0 ms
10 ms
10
1.0
0.1
6
dc
RDS(on) LIMIT
THERMAL LIMIT
PACKAGE LIMIT
1.0
able operation, the stored energy from circuit inductance dissipated in the transistor while in avalanche must be less than
the rated limit and must be adjusted for operating conditions
differing from those specified. Although industry practice is to
rate in terms of energy, avalanche energy capability is not a
constant. The energy rating decreases non–linearly with an
increase of peak current in avalanche and peak junction temperature.
Although many E–FETs can withstand the stress of drain–
to–source avalanche at currents up to rated pulsed current
(IDM), the energy rating is specified at rated continuous current (ID), in accordance with industry custom. The energy rating must be derated for temperature as shown in the
accompanying graph (Figure 12). Maximum energy at currents below rated continuous ID can safely be assumed to
equal the values indicated.
600
ID = 60 A
500
400
300
200
100
0
10
100
25
50
75
100
125
150
175
VDS, DRAIN–TO–SOURCE VOLTAGE (VOLTS)
TJ, STARTING JUNCTION TEMPERATURE (°C)
Figure 12. Maximum Rated Forward Biased
Safe Operating Area
Figure 13. Maximum Avalanche Energy versus
Starting Junction Temperature
Motorola TMOS Power MOSFET Transistor Device Data
r(t), EFFECTIVE TRANSIENT THERMAL RESISTANCE
(NORMALIZED)
MTP60N05HDL
1.0
D = 0.5
0.2
0.1
0.1
P(pk)
0.05
0.02
t1
0.01
t2
DUTY CYCLE, D = t1/t2
SINGLE PULSE
0.01
0.00001
0.0001
0.001
0.01
t, TIME (s)
0.1
RθJC(t) = r(t) RθJC
D CURVES APPLY FOR POWER
PULSE TRAIN SHOWN
READ TIME AT t1
TJ(pk) – TC = P(pk) RθJC(t)
1.0
10
Figure 14. Thermal Response
di/dt
IS
trr
ta
tb
TIME
0.25 IS
tp
IS
Figure 15. Diode Reverse Recovery Waveform
Motorola TMOS Power MOSFET Transistor Device Data
7
MTP60N05HDL
PACKAGE DIMENSIONS
–T–
B
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION Z DEFINES A ZONE WHERE ALL
BODY AND LEAD IRREGULARITIES ARE
ALLOWED.
SEATING
PLANE
C
F
T
S
4
A
Q
1 2 3
U
H
STYLE 5:
PIN 1.
2.
3.
4.
K
Z
L
R
V
J
G
D
N
GATE
DRAIN
SOURCE
DRAIN
DIM
A
B
C
D
F
G
H
J
K
L
N
Q
R
S
T
U
V
Z
INCHES
MIN
MAX
0.570
0.620
0.380
0.405
0.160
0.190
0.025
0.035
0.142
0.147
0.095
0.105
0.110
0.155
0.018
0.025
0.500
0.562
0.045
0.060
0.190
0.210
0.100
0.120
0.080
0.110
0.045
0.055
0.235
0.255
0.000
0.050
0.045
–––
–––
0.080
MILLIMETERS
MIN
MAX
14.48
15.75
9.66
10.28
4.07
4.82
0.64
0.88
3.61
3.73
2.42
2.66
2.80
3.93
0.46
0.64
12.70
14.27
1.15
1.52
4.83
5.33
2.54
3.04
2.04
2.79
1.15
1.39
5.97
6.47
0.00
1.27
1.15
–––
–––
2.04
CASE 221A–06
ISSUE Y
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 4–32–1,
Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. 81–3–5487–8488
Customer Focus Center: 1–800–521–6274
Mfax: [email protected] – TOUCHTONE 1–602–244–6609
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
Motorola Fax Back System
– US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
– http://sps.motorola.com/mfax/
HOME PAGE: http://motorola.com/sps/
8
◊
MTP60N05HDL/D
Motorola TMOS Power MOSFET Transistor
Device Data