ON MAC97A6RL1G Sensitive gate triac Datasheet

MAC97 Series
Sensitive Gate Triacs
Silicon Bidirectional Thyristors
Designed for use in solid state relays, MPU interface, TTL logic and
any other light industrial or consumer application. Supplied in an
inexpensive TO−92 package which is readily adaptable for use in
automatic insertion equipment.
http://onsemi.com
Features
TRIACS
0.8 AMPERE RMS
200 thru 600 VOLTS
• One−Piece, Injection−Molded Package
• Blocking Voltage to 600 Volts
• Sensitive Gate Triggering in Four Trigger Modes (Quadrants) for all
•
•
possible Combinations of Trigger Sources, and especially for Circuits
that Source Gate Drives
All Diffused and Glassivated Junctions for Maximum Uniformity of
Parameters and Reliability
These are Pb−Free Devices*
MT2
MT1
G
MAXIMUM RATINGS (TJ = 25°C unless otherwise noted)
Rating
Symbol
Peak Repetitive Off-State Voltage
(TJ = −40 to +110°C) (Note 1)
Sine Wave 50 to 60 Hz, Gate Open
MAC97A4
MAC97A6
MAC97A8
VDRM,
VRRM
On-State RMS Current
Full Cycle Sine Wave 50 to 60 Hz
(TC = +50°C)
IT(RMS)
Peak Non−Repetitive Surge Current
One Full Cycle, Sine Wave 60 Hz
(TC = 110°C)
ITSM
Value
MARKING
DIAGRAM
Unit
V
200
400
600
1
12
A
3
STRAIGHT LEAD
BULK PACK
8.0
A
TO−92 (TO−226)
CASE 029
STYLE 12
I2t
0.26
A2s
Peak Gate Voltage
(t v 2.0 ms, TC = +80°C)
VGM
5.0
V
Peak Gate Power
(t v 2.0 ms, TC = +80°C)
PGM
5.0
W
Average Gate Power
(TC = 80°C, t v 8.3 ms)
PG(AV)
0.1
W
Peak Gate Current
(t v 2.0 ms, TC = +80°C)
IGM
1.0
A
Operating Junction Temperature Range
TJ
−40 to +110
°C
Storage Temperature Range
Tstg
−40 to +150
°C
Circuit Fusing Considerations (t = 8.3 ms)
0.6
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
1. VDRM and VRRM for all types can be applied on a continuous basis. Blocking
voltages shall not be tested with a constant current source such that the
voltage ratings of the devices are exceeded.
2
3
BENT LEAD
TAPE & REEL
AMMO PACK
MAC
97Ax
AYWWG
G
MAC97Ax = Device Code
x = 4, 6, or 8
A
= Assembly Location
Y
= Year
WW
= Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
PIN ASSIGNMENT
1
Main Terminal 1
2
Gate
3
Main Terminal 2
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 6 of this data sheet.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2013
August, 2013 − Rev. 10
1
Publication Order Number:
MAC97/D
MAC97 Series
THERMAL CHARACTERISTICS
Symbol
Max
Unit
Thermal Resistance, Junction−to−Case
Characteristic
RqJC
75
°C/W
Thermal Resistance, Junction−to−Ambient
RqJA
200
°C/W
TL
260
°C
Maximum Lead Temperature for Soldering Purposes for 10 Seconds
ELECTRICAL CHARACTERISTICS (TC = 25°C unless otherwise noted; Electricals apply in both directions)
Characteristic
Symbol
Min
Typ
Max
Unit
−
−
−
−
10
100
mA
mA
−
−
1.9
V
OFF CHARACTERISTICS
Peak Repetitive Blocking Current
(VD = Rated VDRM, VRRM; Gate Open)
TJ = 25°C
TJ = +110°C
IDRM, IRRM
ON CHARACTERISTICS
Peak On−State Voltage
(ITM = ".85 A Peak; Pulse Width v 2.0 ms, Duty Cycle v 2.0%)
VTM
Gate Trigger Current (Continuous dc)
(VD = 12 Vdc, RL = 100 W)
MT2(+), G(+)
MT2(+), G(−)
MT2(−), G(−)
MT2(−), G(+)
IGT
Gate Trigger Voltage (Continuous dc)
(VD = 12 Vdc, RL = 100 W)
MT2(+), G(+) All Types
MT2(+), G(−) All Types
MT2(−), G(−) All Types
MT2(−), G(+) All Types
VGT
Gate Non−Trigger Voltage
(VD = 12 V, RL = 100 W, TJ = 110°C)
All Four Quadrants
mA
−
−
−
−
−
−
−
−
5.0
5.0
5.0
7.0
V
−
−
−
−
.66
.77
.84
.88
2.0
2.0
2.0
2.5
VGD
0.1
−
−
V
Holding Current
(VD = 12 Vdc, Initiating Current = 200 mA, Gate Open)
IH
−
1.5
10
mA
Turn-On Time
(VD = Rated VDRM, ITM = 1.0 A pk, IG = 25 mA)
tgt
−
2.0
−
ms
dV/dt(c)
−
5.0
−
V/ms
dv/dt
−
25
−
V/ms
DYNAMIC CHARACTERISTICS
Critical Rate−of−Rise of Commutation Voltage
(VD = Rated VDRM, ITM = .84 A,
Commutating di/dt = .3 A/ms, Gate Unenergized, TC = 50°C)
Critical Rate of Rise of Off−State Voltage
(VD = Rated VDRM, TC = 110°C, Gate Open, Exponential Waveform
http://onsemi.com
2
MAC97 Series
Voltage Current Characteristic of Triacs
(Bidirectional Device)
+ Current
Symbol
Parameter
VTM
VDRM
Peak Repetitive Forward Off State Voltage
IDRM
Peak Forward Blocking Current
VRRM
Peak Repetitive Reverse Off State Voltage
IRRM
Peak Reverse Blocking Current
VTM
Maximum On State Voltage
IH
Holding Current
on state
IRRM at VRRM
IH
Quadrant 3
MainTerminal 2 −
IH
off state
VTM
Quadrant Definitions for a Triac
MT2 POSITIVE
(Positive Half Cycle)
+
(+) MT2
Quadrant II
(+) MT2
(−) IGT
GATE
Quadrant I
(+) IGT
GATE
MT1
MT1
REF
REF
IGT −
+ IGT
(−) MT2
Quadrant III
(−) MT2
Quadrant IV
(+) IGT
GATE
(−) IGT
GATE
MT1
MT1
REF
REF
−
MT2 NEGATIVE
(Negative Half Cycle)
All polarities are referenced to MT1.
With in−phase signals (using standard AC lines) quadrants I and III are used.
http://onsemi.com
3
Quadrant 1
MainTerminal 2 +
+ Voltage
IDRM at VDRM
MAC97 Series
110
100
100
I T(RMS) , MAXIMUM ALLOWABLE
AMBIENT TEMPERATURE ( °C)
T = 30°
60°
90
DC
90°
80
180°
70
120°
60
a
50
a
40
30
a = CONDUCTION ANGLE
0.1
0.2
0.3
60°
90
0.4
0.5
0.6
0.7
0.8
90°
DC
80
180°
70
120°
60
a
50
40
20
0
T = 30°
a
30
a = CONDUCTION ANGLE
0
0.05
0.1
0.15
0.2
0.25
0.3
IT(RMS), RMS ON-STATE CURRENT (AMPS)
IT(RMS), RMS ON-STATE CURRENT (AMPS)
Figure 1. RMS Current Derating
Figure 2. RMS Current Derating
1.2
0.35
0.4
5.2
6.0
6.0
4.0
a
1.0
DC
a
0.8
TJ = 110°C
180°
2.0
a = CONDUCTION ANGLE
25°C
120°
0.6
1.0
0.4
ITM , INSTANTANEOUS ON‐STATE CURRENT (AMP)
P (AV), MAXIMUM AVERAGE POWER DISSIPATION (WATTS)
TC, MAXIMUM ALLOWABLE CASE TEMPERATURE ( °C)
110
90°
60°
0.2
T = 30°
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
IT(RMS), RMS ON-STATE CURRENT (AMPS)
Figure 3. Power Dissipation
0.6
0.4
0.2
0.1
0.06
0.04
0.02
0.01
0.006
0.4
1.2
2.0
2.8
3.6
4.4
VTM, INSTANTANEOUS ON‐STATE VOLTAGE (VOLTS)
Figure 4. On−State Characteristics
http://onsemi.com
4
MAC97 Series
10
I TSM , PEAK SURGE CURRENT (AMPS)
R (t), TRANSIENT THERMAL RESISTANCE (NORMALIZED)
1.0
ZQJC(t) = RQJC(t) @ r(t)
0.1
0.01
0.1
1.0
10
1S103
100
5.0
3.0
TJ = 110°C
f = 60 Hz
2.0
Surge is preceded and followed by rated current.
1.0
1.0
1S104
2.0
3.0
5.0
10
30
50
100
NUMBER OF CYCLES
t, TIME (ms)
Figure 5. Transient Thermal Response
Figure 6. Maximum Allowable Surge Current
100
1.2
VGT, GATE TRIGGER VOLTAGE (V)
IGT, GATE TRIGGER CURRENT (mA)
CYCLE
Q4
10
Q3
Q2
Q1
1
1.1
Q4
1.0
Q3
0.9
Q2
0.8
Q1
0.7
0.6
0.5
0.4
0
-40 -25
-10
5
20
35
50
80
65
95
0.3
-40 -25
110
5
20
35
50
65
80
95
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 7. Typical Gate Trigger Current versus
Junction Temperature
Figure 8. Typical Gate Trigger Voltage versus
Junction Temperature
100
110
10
10
IH , HOLDING CURRENT (mA)
IL , LATCHING CURRENT (mA)
-10
Q2
Q3
Q4
1
Q1
0
-40 -25
-10
5
20
35
50
65
80
95
MT2 Negative
1
MT2 Positive
0.1
-40 -25
110
-10
5
20
35
50
65
80
95
TJ, JUNCTION TEMPERATURE (°C)
TJ, JUNCTION TEMPERATURE (°C)
Figure 9. Typical Latching Current versus
Junction Temperature
Figure 10. Typical Holding Current versus
Junction Temperature
http://onsemi.com
5
110
MAC97 Series
LL
200 VRMS
ADJUST FOR
ITM, 60 Hz VAC
MEASURE
I
TRIGGER
TRIGGER CONTROL
CHARGE
1N4007
CHARGE
CONTROL
NON‐POLAR
CL
RS
CS
MT2
1N914 51 W
ADJUST FOR +
dV/dt(c)
200 V
MT1
G
Note: Component values are for verification of rated (dv/dt)c. See AN1048 for additional information.
Figure 11. Simplified Test Circuit to Measure the Critical Rate of Rise of Commutating Voltage (dV/dt)c
ORDERING & SHIPPING INFORMATION
U.S.
MAC97A8RLRMG
Europe
Equivalent
Shipping
Description of TO92 Tape Orientation
MAC97A6RL1G
Radial Tape & Reel (2K/Reel)
(Pb−Free)
Flat side of TO92 & adhesive tape visible
MAC97A8RL1G
Radial Tape & Reel (2K/Reel)
(Pb−Free)
Flat side of TO92 & adhesive tape visible
MAC97A4G
Bulk in Box (5K/Box)
(Pb−Free)
N/A, Bulk
MAC97A6G
Bulk in Box (5K/Box)
(Pb−Free)
N/A, Bulk
MAC97A8G
Bulk in Box (5K/Box)
(Pb−Free)
N/A, Bulk
MAC97A4RLRFG
Radial Tape & Reel (2K/Reel)
(Pb−Free)
Round side of TO92 & adhesive tape on reverse side
MAC97A4RLRPG
Radial Tape & Reel (2K/Reel)
(Pb−Free)
Round side of TO92 & adhesive tape on reverse side
MAC97A6RLRFG
Radial Tape & Reel (2K/Reel)
(Pb−Free)
Round side of TO92 & adhesive tape on reverse side
MAC97A6RLRPG
Radial Tape & Reel (2K/Reel)
(Pb−Free)
Round side of TO92 & adhesive tape on reverse side
MAC97A8RLRPG
Radial Tape / Fan Fold Box (2K/Box)
(Pb−Free)
Round side of TO92 & adhesive tape visible
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
6
MAC97 Series
TO−92 EIA RADIAL TAPE IN FAN FOLD BOX OR ON REEL
H2A
H2A
H2B
H2B
H
W2
H4 H5
T1
L1
H1
W1 W
L
T
T2
F1
F2
P2
D
P2
P1
P
Figure 12. Device Positioning on Tape
Specification
Inches
Symbol
Item
Millimeter
Min
Max
Min
Max
D
Tape Feedhole Diameter
0.1496
0.1653
3.8
4.2
D2
Component Lead Thickness Dimension
0.015
0.020
0.38
0.51
Component Lead Pitch
0.0945
0.110
2.4
2.8
.059
0.156
1.5
4.0
0.3346
0.3741
8.5
9.5
0
0.039
0
1.0
F1, F2
H
Bottom of Component to Seating Plane
H1
Feedhole Location
H2A
Deflection Left or Right
H2B
Deflection Front or Rear
0
0.051
0
1.0
H4
Feedhole to Bottom of Component
0.7086
0.768
18
19.5
H5
Feedhole to Seating Plane
0.610
0.649
15.5
16.5
L
Defective Unit Clipped Dimension
0.3346
0.433
8.5
11
L1
Lead Wire Enclosure
0.09842
−
2.5
−
P
Feedhole Pitch
0.4921
0.5079
12.5
12.9
P1
Feedhole Center to Center Lead
0.2342
0.2658
5.95
6.75
P2
First Lead Spacing Dimension
0.1397
0.1556
3.55
3.95
0.06
0.08
0.15
0.20
−
0.0567
−
1.44
T
Adhesive Tape Thickness
T1
Overall Taped Package Thickness
T2
Carrier Strip Thickness
0.014
0.027
0.35
0.65
W
Carrier Strip Width
0.6889
0.7481
17.5
19
W1
Adhesive Tape Width
0.2165
0.2841
5.5
6.3
W2
Adhesive Tape Position
0.0059
0.01968
0.15
0.5
NOTES:
2. Maximum alignment deviation between leads not to be greater than 0.2 mm.
3. Defective components shall be clipped from the carrier tape such that the remaining protrusion (L) does not exceed a maximum of 11 mm.
4. Component lead to tape adhesion must meet the pull test requirements.
5. Maximum non−cumulative variation between tape feed holes shall not exceed 1 mm in 20 pitches.
6. Holddown tape not to extend beyond the edge(s) of carrier tape and there shall be no exposure of adhesive.
7. No more than 1 consecutive missing component is permitted.
8. A tape trailer and leader, having at least three feed holes is required before the first and after the last component.
9. Splices will not interfere with the sprocket feed holes.
http://onsemi.com
7
MAC97 Series
PACKAGE DIMENSIONS
TO−92 (TO−226)
CASE 29−11
ISSUE AM
A
B
STRAIGHT LEAD
BULK PACK
R
P
L
SEATING
PLANE
K
D
X X
G
J
H
V
C
SECTION X−X
N
1
N
BENT LEAD
TAPE & REEL
AMMO PACK
B
P
T
SEATING
PLANE
G
K
D
X X
J
V
1
DIM
A
B
C
D
G
H
J
K
L
N
P
R
V
INCHES
MIN
MAX
0.175
0.205
0.170
0.210
0.125
0.165
0.016
0.021
0.045
0.055
0.095
0.105
0.015
0.020
0.500
--0.250
--0.080
0.105
--0.100
0.115
--0.135
---
MILLIMETERS
MIN
MAX
4.45
5.20
4.32
5.33
3.18
4.19
0.407
0.533
1.15
1.39
2.42
2.66
0.39
0.50
12.70
--6.35
--2.04
2.66
--2.54
2.93
--3.43
---
STYLE 12:
PIN 1. MAIN TERMINAL 1
2. GATE
3. MAIN TERMINAL 2
A
R
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. CONTOUR OF PACKAGE BEYOND DIMENSION R
IS UNCONTROLLED.
4. LEAD DIMENSION IS UNCONTROLLED IN P AND
BEYOND DIMENSION K MINIMUM.
C
N
SECTION X−X
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. CONTOUR OF PACKAGE BEYOND
DIMENSION R IS UNCONTROLLED.
4. LEAD DIMENSION IS UNCONTROLLED IN P
AND BEYOND DIMENSION K MINIMUM.
DIM
A
B
C
D
G
J
K
N
P
R
V
MILLIMETERS
MIN
MAX
4.45
5.20
4.32
5.33
3.18
4.19
0.40
0.54
2.40
2.80
0.39
0.50
12.70
--2.04
2.66
1.50
4.00
2.93
--3.43
---
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
8
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MAC97/D
Similar pages