Allegro A6B273KLWTR-T 8-bit latched dmos power driver Datasheet

Data Sheet
26180.122b
6B273
8-BIT LATCHED
DMOS POWER DRIVER
20
LOGIC
SUPPLY
2
19
IN 8
IN 2
3
18
IN 7
OUT 1
4
17
OUT 8
OUT 2
5
16
OUT 7
OUT 3
6
15
OUT 6
OUT 4
7
14
OUT 5
IN 3
8
13
IN 6
IN 4
9
12
IN 5
GROUND
10
11
STROBE
IN 1
VDD
LATCHES
1
LATCHES
CLEAR
Dwg. PP-015-2A
Note that the A6B273KA (DIP) and the A6B273KLW
(SOIC) are electrically identical and share a common
terminal number assignment.
ABSOLUTE MAXIMUM RATINGS
at TA = 25°C
Output Voltage, VO ............................... 50 V
Output Drain Current,
Continuous, IO .......................... 150 mA*
Peak, IOM ................................... 500 mA†
Single-Pulse Avalanche Energy,
EAS ................................................. 30 mJ
Logic Supply Voltage, VDD .................. 7.0 V
Input Voltage Range,
VI ................................... -0.3 V to +7.0 V
Package Power Dissipation,
PD ........................................... See Graph
Operating Temperature Range,
TA ................................. -40°C to +125°C
Storage Temperature Range,
TS ................................. -55°C to +150°C
* Each output, all outputs on.
† Pulse duration ≤ 100 µs, duty cycle ≤ 2%.
Caution: These CMOS devices have input static
protection (Class 3) but are still susceptible to damage if
exposed to extremely high static electrical charges.
The A6B273KA and A6B273KLW combine eight (positive-edgetriggered D-type) data latches and DMOS outputs for systems requiring
relatively high load power. Driver applications include relays, solenoids, and other medium-current or high-voltage peripheral power
loads. The CMOS inputs and latches allow direct interfacing with
microprocessor-based systems. Use with TTL may require appropriate
pull-up resistors to ensure an input logic high.
The DMOS output inverts the DATA input. All of the output
drivers are disabled (the DMOS sink drivers turned OFF) with the
CLEAR input low. The A6B273KA/KLW DMOS open-drain outputs
are capable of sinking up to 500 mA. Similar devices with reduced
rDS(on) are available as the A6273KA/KLW.
The A6B273KA is furnished in a 20-pin dual in-line plastic
package. The A6B273KLW is furnished in a 20-lead wide-body,
small-outline plastic package (SOIC) with gull-wing leads for surfacemount applications. Copper lead frames, reduced supply current
requirements, and low on-state resistance allow both devices to sink
150 mA from all outputs continuously, to ambient temperatures over
85°C.
FEATURES
■ 50 V Minimum Output Clamp Voltage
■ 150 mA Output Current (all outputs simultaneously)
■ 5 Ω Typical rDS(on)
■ Low Power Consumption
■ Replacements for TPIC6B273N and TPIC6B273DW
Selection Guide
Part Number
Pb-free*
Package
Packing
A6B273KLW-T
A6B273KLWTR-T
Yes
Yes
20-pin SOICW
20-pin SOICW
37 per tube
1000 per reel
RθJA
(°C/W)
70
70
RθJC
(°C/W)
17
17
*Pb-based variants are being phased out of the product line. Some variants cited in
this footnote are in production but have been determined to be LAST TIME BUY or
NOT FOR NEW DESIGN. This classification indicates that sale of this device is currently
restricted to existing customer applications. The variants should not be purchased for new
design applications because obsolescence in the near future is probable. Samples are no
longer available. Status change for LAST TIME BUY: October 31, 2006. Deadline for
receipt of LAST TIME BUY orders: April 27, 2007. These variants include: A6B273KLW and
A6B273KLWTR. Status change for NOT FOR NEW DESIGN: May 1, 2006. These variants
include: A6B273KA.
6B273
8-BIT LATCHED
DMOS POWER DRIVER
ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS
LOGIC SYMBOL
2.5
1
R
11
C1
2.0
SU
FF
IX
1.5
'A
', R
θJ
A =
SU
FF
IX
'LW
', R
1.0
55
°C
/W
θJA =
90
°C
/W
0.5
0
25
50
75
100
125
AMBIENT TEMPERATURE IN ° C
150
2
1D
4
3
1D
5
8
1D
6
9
1D
7
12
1D
14
13
1D
15
18
1D
16
19
1D
17
Dwg. FP-046-1A
Dwg. GS-004B
VDD
OUT
IN
Dwg. EP-010-16
Dwg. EP-063
LOGIC INPUTS
DMOS POWER DRIVER OUTPUT
FUNCTION TABLE
CLEAR
L
H
H
H
Inputs
STROBE
X
L
INX
OUTX
X
H
L
X
H
L
H
R
L = Low Logic Level
H = High Logic Level
X = Irrelevant
R = Previous State
115 Northeast Cutoff, Box 15036
Worcester,
Massachusetts 01615-0036 (508) 853-5000
W
Copyright © 2002 Allegro MicroSystems, Inc.
6B273
8-BIT LATCHED
DMOS POWER DRIVER
FUNCTIONAL BLOCK DIAGRAM
IN 1
D
OUT 1
C1
STROBE
CLR
IN2
LOGIC
SUPPLY
IN 3
D
OUT 2
C1
V DD
CLR
D
OUT 3
C1
CLR
IN 4
D
OUT 4
C1
CLR
IN5
D
OUT 5
C1
CLR
IN6
D
OUT 6
C1
CLR
IN 7
D
OUT 7
C1
CLR
IN8
D
OUT 8
C1
CLEAR
CLR
GROUND
(ACTIVE LOW)
Dwg. FP-016-2
www.allegromicro.com
6B273
8-BIT LATCHED
DMOS POWER DRIVER
RECOMMENDED OPERATING CONDITIONS
over operating temperature range
Logic Supply Voltage Range, VDD ............... 4.5 V to 5.5 V
High-Level Input Voltage, VIH ............................ ≥ 0.85VDD
Low-level input voltage, VIL ................................. ≤0.15VDD
ELECTRICAL CHARACTERISTICS at TA = +25°C, VDD = 5 V, tir = tif ≤ 10 ns (unless otherwise
specified).
Limits
Characteristic
Logic Supply Voltage
Output Breakdown
Voltage
Off-State Output
Current
Static Drain-Source
On-State Resistance
Symbol
Test Conditions
Min.
Typ.
Max.
Units
VDD
Operating
4.5
5.0
5.5
V
V(BR)DSX
IO = 1 mA
50
—
—
V
VO = 40 V, VDD = 5.5 V
—
0.1
5.0
µA
VO = 40 V, VDD = 5.5 V, TA = 125°C
—
0.15
8.0
µA
IO = 100 mA, VDD = 4.5 V
—
4.2
5.7
Ω
IO = 100 mA, VDD = 4.5 V, TA = 125°C
—
6.8
9.5
Ω
IO = 350 mA, VDD = 4.5 V (see note)
—
5.5
8.0
Ω
IDSX
rDS(on)
Nominal Output
Current
ION
VDS(on) = 0.5 V, TA = 85°C
—
90
—
mA
Logic Input Current
IIH
VI = VDD = 5.5 V
—
—
1.0
µA
IIL
VI = 0, VDD = 5.5 V
—
—
-1.0
µA
tPLH
IO = 100 mA, CL = 30 pF
—
150
—
ns
tPHL
IO = 100 mA, CL = 30 pF
—
90
—
ns
Output Rise Time
tr
IO = 100 mA, CL = 30 pF
—
200
—
ns
Output Fall Time
tf
IO = 100 mA, CL = 30 pF
—
200
—
ns
IDD(OFF)
VDD = 5.5 V, Outputs off
—
20
100
µA
IDD(ON)
VDD = 5.5 V, Outputs on
—
150
300
µA
Prop. Delay Time
Supply Current
Typical Data is at VDD = 5 V and is for design information only.
NOTE — Pulse test, duration ≤100 µs, duty cycle ≤2%.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
6B273
8-BIT LATCHED
DMOS POWER DRIVER
TIMING REQUIREMENTS
50%
INx
t su(D)
50%
t h(D)
t su(D)
t h(D)
50%
STROBE
t PLH
t PHL
90%
OUTPUTx
10%
tr
tf
Dwg. WP-036-1
Input Active Time Before Strobe
(Data Set-Up Time), tsu(D) .............................................. 20 ns
Input Active Time After Strobe
(Data Hold Time), th(D) ................................................... 20 ns
Input Pulse Width, tw(D) ....................................................... 40 ns
Input Logic High, VIH ................................................ ≥ 0.85VCC
Input Logic Low, VIL ................................................. ≤ 0.15VCC
TEST CIRCUITS
+15 V
10.5 Ω
INPUT
200 mH
tav
IAS = 500 mA
IO
DUT
OUT
VO
V(BR)DSX
VO(ON)
Dwg. EP-066
EAS = IAS x V(BR)DSX x tAV/2
www.allegromicro.com
Single-Pulse Avalanche Energy Test Circuit
and Waveforms
6B273
8-BIT LATCHED
DMOS POWER DRIVER
TERMINAL DESCRIPTIONS
Terminal No.
Terminal Name
Function
1
CLEAR
When (active) LOW, all latches are reset and all outputs go HIGH (turn OFF).
2
IN1
CMOS data input to a latch. When strobed, the output then inverts the data
input (IN1 = HIGH, OUT1 = LOW).
3
IN2
CMOS data input to a latch. When strobed, the output then inverts the data
input (IN2 = HIGH, OUT2 = LOW).
4
OUT1
Current-sinking, open-drain DMOS output.
5
OUT2
Current-sinking, open-drain DMOS output.
6
OUT3
Current-sinking, open-drain DMOS output.
7
OUT4
Current-sinking, open-drain DMOS output.
8
IN3
CMOS data input to a latch. When strobed, the output then inverts the data
input (IN3 = HIGH, OUT3 = LOW).
9
IN4
CMOS data input to a latch. When strobed, the output then inverts the data
input (IN4 = HIGH, OUT4 = LOW).
10
GROUND
Reference terminal for all voltage measurements.
11
STROBE
A CMOS dynamic input to all latches. Data on each INx terminal is loaded
into its associated latch on a low-to-high STROBE transition.
12
IN5
CMOS data input to a latch. When strobed, the output then inverts the data
input (IN5 = HIGH, OUT5 = LOW).
13
IN6
CMOS data input to a latch. When strobed, the output then inverts the data
input (IN6 = HIGH, OUT6 = LOW).
14
OUT5
Current-sinking, open-drain DMOS output.
15
OUT6
Current-sinking, open-drain DMOS output.
16
OUT7
Current-sinking, open-drain DMOS output.
17
OUT8
Current-sinking, open-drain DMOS output.
18
IN7
CMOS data input to a latch. When strobed, the output then inverts the data
input (IN7 = HIGH, OUT7 = LOW).
19
IN8
CMOS data input to a latch. When strobed, the output then inverts the data
input (IN8 = HIGH, OUT8 = LOW).
20
LOGIC SUPPLY
(VDD) The logic supply voltage (typically 5 V).
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
6B273
8-BIT LATCHED
DMOS POWER DRIVER
A6B273KA
Dimensions in Inches
(controlling dimensions)
20
0.014
0.008
11
0.430
MAX
0.280
0.240
0.300
BSC
1
0.070
0.045
0.100
1.060
0.980
10
0.005
BSC
MIN
0.210
MAX
0.150
0.115
0.015
MIN
0.022
0.014
Dwg. MA-001-20 in
Dimensions in Millimeters
(for reference only)
20
0.355
0.204
11
10.92
MAX
7.11
6.10
7.62
BSC
1
1.77
1.15
2.54
26.92
24.89
BSC
10
0.13
MIN
5.33
MAX
3.81
2.93
0.39
MIN
0.558
0.356
NOTES: 1.
2.
3.
4.
Exact body and lead configuration at vendor’s option within limits shown.
Lead spacing tolerance is non-cumulative.
Lead thickness is measured at seating plane or below.
Supplied in standard sticks/tubes of 18 devices.
www.allegromicro.com
Dwg. MA-001-20 mm
6B273
8-BIT LATCHED
DMOS POWER DRIVER
A6B273KLW
Dimensions in Inches
(for reference only)
20
11
0.0125
0.0091
0.419
0.394
0.2992
0.2914
0.050
0.016
0.020
0.013
1
2
0.050
3
0.5118
0.4961
0° TO 8°
BSC
0.0926
0.1043
Dwg. MA-008-20 in
0.0040 MIN.
Dimensions in Millimeters
(controlling dimensions)
20
11
0.32
0.23
10.65
10.00
7.60
7.40
1.27
0.40
0.51
0.33
1
2
1.27
3
13.00
12.60
BSC
0° TO 8°
2.65
2.35
0.10 MIN.
Dwg. MA-008-20 mm
NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown.
2. Lead spacing tolerance is non-cumulative.
3. Supplied in standard sticks/tubes of 37 devices or add ‘TR’ to part number for tape and reel.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
6B273
8-BIT LATCHED
DMOS POWER DRIVER
The products described here are manufactured under one or more
U.S. patents or U.S. patents pending.
Allegro MicroSystems, Inc. reserves the right to make, from time to
time, such departures from the detail specifications as may be
required to permit improvements in the performance, reliability, or
manufacturability of its products. Before placing an order, the user is
cautioned to verify that the information being relied upon is current.
Allegro products are not authorized for use as critical components
in life-support devices or systems without express written approval.
The information included herein is believed to be accurate and
reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of
third parties which may result from its use.
www.allegromicro.com
6B273
8-BIT LATCHED
DMOS POWER DRIVER
POWER
INTERFACE DRIVERS
Function
Output Ratings*
Part Number†
SERIAL-INPUT LATCHED DRIVERS
8-Bit (saturated drivers)
8-Bit
8-Bit
8-Bit
8-Bit
8-Bit (constant-current LED driver)
8-Bit (constant-current LED driver)
8-Bit (DMOS drivers)
8-Bit (DMOS drivers)
8-Bit (DMOS drivers)
-120 mA
350 mA
350 mA
350 mA
350 mA
75 mA
120 mA
250 mA
350 mA
100 mA
50 V‡
50 V
80 V
50 V‡
80 V‡
17 V
24 V
50 V
50 V‡
50 V
5895
5821
5822
5841
5842
6275
6277
6595
6A595
6B595
10-Bit (active pull-downs)
-25 mA
60 V
5810-F and 6810
12-Bit (active pull-downs)
-25 mA
60 V
5811
75 mA
17 V
6276
20-Bit (active pull-downs)
-25 mA
60 V
5812-F and 6812
32-Bit (active pull-downs)
32-Bit
32-Bit (saturated drivers)
-25 mA
100 mA
100 mA
60 V
30 V
40 V
5818-F and 6818
5833
5832
16-Bit (constant-current LED driver)
PARALLEL-INPUT LATCHED DRIVERS
4-Bit
350 mA
50 V‡
5800
8-Bit
8-Bit
8-Bit (DMOS drivers)
8-Bit (DMOS drivers)
-25 mA
350 mA
100 mA
250 mA
60 V
50 V‡
50 V
50 V
5815
5801
6B273
6273
SPECIAL-PURPOSE DEVICES
Unipolar Stepper Motor Translator/Driver
Addressable 8-Bit Decoder/DMOS Driver
Addressable 8-Bit Decoder/DMOS Driver
Addressable 8-Bit Decoder/DMOS Driver
Addressable 28-Line Decoder/Driver
1.25 A
250 mA
350 mA
100 mA
450 mA
50 V‡
50 V
50 V‡
50 V
30 V
5804
6259
6A259
6B259
6817
*
Current is maximum specified test condition, voltage is maximum rating. See specification for sustaining voltage limits.
Negative current is defined as coming out of (sourcing) the output.
†
Complete part number includes additional characters to indicate operating temperature range and package style.
‡
Internal transient-suppression diodes included for inductive-load protection.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Similar pages