STMicroelectronics L78M05AB Precision 500 ma regulator Datasheet

L78MxxAB
L78MxxAC
Precision 500 mA regulators
Datasheet − production data
Features
■
Output current to 0.5 A
■
Output voltages of 5; 6; 8; 9; 10; 12; 15; 24 V
■
Thermal overload protection
■
Short circuit protection
■
Output transition SOA protection
■
± 2 % output voltage tolerance
■
Guaranteed in extended temperature range
TO-220
DPAK
Description
The L78MxxA series of three-terminal positive
regulators is available in TO-220 and DPAK
packages and with several fixed output voltages,
making it useful in a wide range of applications.
These regulators can provide local on-card
regulation eliminating the distribution problems
associated with single point regulation. Each type
employs internal current limiting, thermal
shutdown and safe area protection, making it
essentially indestructible. If adequate heat sinking
is provided, they can deliver over 0.5 A output
current. Although designed primarily as fixed
voltage regulators, these devices can be used
with external components to obtain adjustable
voltage and currents.
Table 1.
Device summary
Part numbers
L78M05AB
L78M12AB
L78M05AC
L78M12AC
L78M06AB
L78M15AB
L78M08AB
L78M24AB
L78M09AB
L78M24AC
L78M10AB
May 2012
This is information on a product in full production.
Doc ID 2147 Rev 13
1/31
www.st.com
31
Contents
L78MxxAB, L78MxxAC
Contents
1
Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4
Test circuits
5
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6
Typical performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7
Applications information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.1
............................................... 6
Design considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
8
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
9
Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
10
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
2/31
Doc ID 2147 Rev 13
L78MxxAB, L78MxxAC
1
Diagram
Figure 1.
Block diagram
Diagram
Doc ID 2147 Rev 13
3/31
Pin configuration
L78MxxAB, L78MxxAC
2
Pin configuration
Figure 2.
Pin connections (top view)
TO-220
Figure 3.
4/31
DPAK
Schematic diagram
Doc ID 2147 Rev 13
L78MxxAB, L78MxxAC
Maximum ratings
3
Maximum ratings
Table 2.
Absolute maximum ratings
Symbol
Parameter
Value
for VO = 5 to 18 V
35
for VO = 20, 24 V
40
Unit
VI
DC input voltage
IO
Output current
Internally limited
mA
PD
Power dissipation
Internally limited
mW
-65 to 150
°C
TSTG
Storage temperature range
TOP
Operating junction temperature range
V
for L78M00AC
0 to 125
for L78M00AB
-40 to 125
°C
Note:
Absolute maximum ratings are those values beyond which damage to the device may occur.
Functional operation under these condition is not implied.
Table 3.
Thermal data
Symbol
Parameter
TO-220
DPAK
Unit
RthJC
Thermal resistance junction-case
5
8
°C/W
RthJA
Thermal resistance junction-ambient
50
100
°C/W
Figure 4.
Application circuit
Doc ID 2147 Rev 13
5/31
Test circuits
4
Test circuits
Figure 5.
DC parameter
Figure 6.
Load regulation
Figure 7.
Ripple rejection
6/31
L78MxxAB, L78MxxAC
Doc ID 2147 Rev 13
L78MxxAB, L78MxxAC
5
Electrical characteristics
Electrical characteristics
Refer to the test circuits, VI = 10 V, IO = 350 mA, CI = 0.33 µF, CO = 0.1 µF,
TJ = -40 to 125 °C (AB), TJ = 0 to 125 °C (AC) unless otherwise specified.
Table 4.
Symbol
Electrical characteristics of L78M05XX
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
4.9
5
5.1
V
VO
Output voltage
IO = 5 to 350 mA, VI = 7 to 20 V
4.8
5
5.2
V
ΔVO
Line regulation
ΔVO
Load regulation
Id
ΔId
ΔVO/ΔT
Quiescent current
Quiescent current change
VI = 7 to 25 V, IO = 200 mA, TJ = 25°C
100
VI = 8 to 25 V, IO = 200 mA, TJ = 25°C
50
IO = 5 to 500 mA, TJ = 25°C
100
IO = 5 to 200 mA, TJ = 25°C
50
TJ = 25°C
6
mV
mV
IO = 5 to 350 mA
0.5
IO = 200 mA, VI = 8 to 25 V
0.8
mA
mA
Output voltage drift
IO = 5 mA
Supply voltage rejection
VI = 8 to 18 V, f = 120Hz, IO = 300mA,
TJ = 25°C
eN
Output noise voltage
B =10Hz to 100kHz, TJ = 25°C
40
µV
Vd
Dropout voltage
TJ = 25°C
2
V
Isc
Short circuit current
TJ = 25°C, VI = 35 V
300
mA
Iscp
Short circuit peak current
TJ = 25°C
700
mA
SVR
Doc ID 2147 Rev 13
-0.5
62
mV/°C
dB
7/31
Electrical characteristics
L78MxxAB, L78MxxAC
Refer to the test circuits, VI = 11 V, IO = 350 mA, CI = 0.33 µF, CO = 0.1 µF,
TJ = -40 to 125 °C (AB), TJ = 0 to 125 °C (AC) unless otherwise specified.
Table 5.
Symbol
Electrical characteristics of L78M06XX
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
5.88
6
6.12
V
VO
Output voltage
IO = 5 to 350 mA, VI = 8 to 21 V
5.75
6
6.3
V
ΔVO
Line regulation
ΔVO
Load regulation
Id
ΔId
ΔVO/ΔT
Quiescent current
Quiescent current change
VI = 8 to 25 V, IO = 200 mA, TJ = 25°C
100
VI = 9 to 25 V, IO = 200 mA, TJ = 25°C
30
IO = 5 to 500 mA, TJ = 25°C
120
IO = 5 to 200 mA, TJ = 25°C
60
TJ = 25°C
6
mV
mV
IO = 5 to 350 mA
0.5
IO = 200 mA, VI = 9 to 25 V
0.8
mA
mA
Output voltage drift
IO = 5 mA
Supply voltage rejection
VI = 9 to 19 V, f = 120Hz, IO = 300mA,
TJ = 25°C
eN
Output noise voltage
B =10Hz to 100kHz
45
µV
Vd
Dropout voltage
TJ = 25°C
2
V
Isc
Short circuit current
TJ = 25°C, VI = 35 V
270
mA
Iscp
Short circuit peak current
TJ = 25°C
700
mA
SVR
8/31
Doc ID 2147 Rev 13
-0.5
59
mV/°C
dB
L78MxxAB, L78MxxAC
Electrical characteristics
Refer to the test circuits, VI = 14 V, IO = 350 mA, CI = 0.33 µF, CO = 0.1 µF, TJ = -40 to 125
°C (AB), TJ = 0 to 125 °C (AC) unless otherwise specified).
Table 6.
Symbol
Electrical characteristics of L78M08XX
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
7.84
8
8.16
V
VO
Output voltage
IO = 5 to 350 mA, VI = 10.5 to 23 V
7.7
8
8.3
V
ΔVO
VI = 10.5 to 25 V, IO = 200 mA,
TJ = 25°C
100
Line regulation
VI = 11 to 25 V, IO = 200 mA, TJ = 25°C
30
IO = 5 to 500 mA, TJ = 25°C
160
IO = 5 to 200 mA, TJ = 25°C
80
TJ = 25°C
6
ΔVO
Id
ΔId
ΔVO/ΔT
Load regulation
Quiescent current
Quiescent current change
mV
mV
IO = 5 to 350 mA
0.5
IO = 200 mA, VI = 10.5 to 25 V
0.8
mA
mA
Output voltage drift
IO = 5 mA
Supply voltage rejection
VI = 11.5 to 21.5 V, f = 120Hz
IO = 300mA, TJ = 25°C
eN
Output noise voltage
B =10Hz to 100kHz, TJ = 25°C
52
µV
Vd
Dropout voltage
TJ = 25°C
2
V
Isc
Short circuit current
TJ = 25°C, VI = 35 V
250
mA
Iscp
Short circuit peak current
TJ = 25°C
700
mA
SVR
Doc ID 2147 Rev 13
-0.5
56
mV/°C
dB
9/31
Electrical characteristics
L78MxxAB, L78MxxAC
Refer to the test circuits, VI = 15 V, IO = 350 mA, CI = 0.33 µF, CO = 0.1 µF,
TJ = -40 to 125 °C (AB), TJ = 0 to 125 °C (AC) unless otherwise specified).
Table 7.
Symbol
Electrical characteristics of L78M09XX
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
8.82
9
9.18
V
VO
Output voltage
IO = 5 to 350 mA, VI = 11.5 to 24 V
8.64
9
9.36
V
ΔVO
VI = 11.5 to 25 V, IO = 200 mA,
TJ = 25°C
100
Line regulation
VI = 12 to 25 V, IO = 200 mA, TJ = 25°C
30
IO = 5 to 500 mA, TJ = 25°C
180
IO = 5 to 200 mA, TJ = 25°C
90
TJ = 25°C
6
ΔVO
Id
ΔId
ΔVO/ΔT
Load regulation
Quiescent current
Quiescent current change
mV
mV
IO = 5 to 350 mA
0.5
IO = 200 mA, VI = 11.5 to 25 V
0.8
mA
mA
Output voltage drift
IO = 5 mA
Supply voltage rejection
VI = 12.5 to 23 V, f = 120Hz,
IO = 300mA, TJ = 25°C
eN
Output noise voltage
B =10Hz to 100kHz, TJ = 25°C
52
µV
Vd
Dropout voltage
TJ = 25°C
2
V
Isc
Short circuit current
VI = 35 V, TJ = 25°C
250
mA
Iscp
Short circuit peak current
TJ = 25°C
700
mA
SVR
10/31
Doc ID 2147 Rev 13
-0.5
56
mV/°C
dB
L78MxxAB, L78MxxAC
Electrical characteristics
Refer to the test circuits, VI = 16 V, IO = 350 mA, CI = 0.33 µF, CO = 0.1 µF,
TJ = -40 to 125 °C (AB), TJ = 0 to 125 °C (AC) unless otherwise specified.
Table 8.
Symbol
Electrical characteristics of L78M10XX
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
9.8
10
10.2
V
VO
Output voltage
IO = 5 to 350 mA, VI = 12.5 to 25 V
9.6
10
10.4
V
ΔVO
VI = 12.5 to 30 V, IO = 200 mA,
TJ = 25°C
100
Line regulation
VI = 13 to 30 V, IO = 200 mA, TJ = 25°C
30
IO = 5 to 500 mA, TJ = 25°C
200
IO = 5 to 200 mA, TJ = 25°C
100
ΔVO
Id
ΔId
ΔVO/ΔT
Load regulation
Quiescent current
Quiescent current change
mV
mV
TJ = 25°C
6
IO = 5 to 350 mA
0.5
IO = 200 mA, VI = 12.5 to 30 V
0.8
mA
mA
Output voltage drift
IO = 5 mA
Supply voltage rejection
VI = 13.5 to 24 V, f = 120Hz,
IO = 300mA, TJ = 25°C
eN
Output noise voltage
B =10Hz to 100kHz, TJ = 25°C
64
µV
Vd
Dropout voltage
TJ = 25°C
2
V
Isc
Short circuit current
VI = 35 V, TJ = 25°C
245
mA
Iscp
Short circuit peak current
TJ = 25°C
700
mA
SVR
Doc ID 2147 Rev 13
-0.5
56
mV/°C
dB
11/31
Electrical characteristics
L78MxxAB, L78MxxAC
Refer to the test circuits, VI = 19 V, IO = 350 mA, CI = 0.33 µF, CO = 0.1 µF,
TJ = -40 to 125 °C (AB), TJ = 0 to 125 °C (AC) unless otherwise specified.
Table 9.
Symbol
Electrical characteristics of L78M12XX
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
11.75
12
12.25
V
VO
Output voltage
IO = 5 to 350 mA, VI = 14.5 to 27 V
11.5
12
12.5
V
ΔVO
VI = 14.5 to 30 V, IO = 200 mA,
TJ = 25°C
100
Line regulation
VI = 16 to 30 V, IO = 200 mA, TJ = 25°C
30
IO = 5 to 500 mA, TJ = 25°C
240
IO = 5 to 200 mA, TJ = 25°C
120
ΔVO
Id
ΔId
ΔVO/ΔT
Load regulation
Quiescent current
Quiescent current change
mV
mV
TJ = 25°C
6
IO = 5 to 350 mA
0.5
IO = 200 mA, VI = 14.5 to 30 V
0.8
mA
mA
Output voltage drift
IO = 5 mA
Supply voltage rejection
VI = 15 to 25 V, f = 120Hz, IO = 300mA,
TJ = 25°C
eN
Output noise voltage
B =10Hz to 100kHz, TJ = 25°C
75
µV
Vd
Dropout voltage
TJ = 25°C
2
V
Isc
Short circuit current
VI = 35 V, TJ = 25°C
240
mA
Iscp
Short circuit peak current
TJ = 25°C
700
mA
SVR
12/31
Doc ID 2147 Rev 13
-1
55
mV/°C
dB
L78MxxAB, L78MxxAC
Electrical characteristics
Refer to the test circuits, VI = 23 V, IO = 350 mA, CI = 0.33 µF, CO = 0.1 µF,
TJ = -40 to 125 °C (AB), TJ = 0 to 125 °C (AC) unless otherwise specified.
Table 10.
Symbol
Electrical characteristics of L78M15XX
Parameter
Test conditions
Min.
Typ.
Max.
Unit
VO
Output voltage
TJ = 25°C
14.7
15
15.3
V
VO
Output voltage
IO = 5 to 350 mA, VI = 17.5 to 30 V
14.4
15
15.6
V
ΔVO
VI = 17.5 to 30 V, IO = 200 mA,
TJ = 25°C
100
Line regulation
VI = 20 to 30 V, IO = 200 mA, TJ = 25°C
30
IO = 5 to 500 mA, TJ = 25°C
300
IO = 5 to 200 mA, TJ = 25°C
150
ΔVO
Id
ΔId
ΔVO/ΔT
Load regulation
Quiescent current
Quiescent current change
mV
mV
TJ = 25°C
6
IO = 5 to 350 mA
0.5
IO = 200 mA, VI = 17.5 to 30 V
0.8
mA
mA
Output voltage drift
IO = 5 mA
Supply voltage rejection
VI = 18.5 to 28.5 V, f = 120Hz,
IO = 300mA, TJ = 25°C
eN
Output noise voltage
B =10Hz to 100kHz, TJ = 25°C
90
µV
Vd
Dropout voltage
TJ = 25°C
2
V
Isc
Short circuit current
VI = 35 V, TJ = 25°C
240
mA
Iscp
Short circuit peak current
TJ = 25°C
700
mA
SVR
Doc ID 2147 Rev 13
-1
54
mV/°C
dB
13/31
Electrical characteristics
L78MxxAB, L78MxxAC
Refer to the test circuits, VI = 33 V, IO = 350 mA, CI = 0.33 µF, CO = 0.1 µF,
TJ = -40 to 125 °C (AB), TJ = 0 to 125 °C (AC) unless otherwise specified.
Table 11.
Symbol
Electrical characteristics of L78M24XX
Parameter
Test conditions
VO
Output voltage
TJ = 25°C
VO
Output voltage
IO = 5 to 350 mA, VI = 27 to 38 V
ΔVO
Line regulation
ΔVO
Load regulation
Id
ΔId
ΔVO/ΔT
Quiescent current
Quiescent current change
Max.
Unit
23.5
24
24.5
V
23
24
25
V
100
VI = 28 to 38 V, IO = 200 mA, TJ = 25°C
30
IO = 5 to 500 mA, TJ = 25°C
480
IO = 5 to 200 mA, TJ = 25°C
240
mV
mV
TJ = 25°C
6
IO = 5 to 350 mA
0.5
IO = 200 mA, VI = 27 to 38 V
0.8
IO = 5 mA
Supply voltage rejection
VI = 28 to 38 V, f = 120Hz, IO = 300mA,
TJ = 25°C
eN
Output noise voltage
B =10Hz to 100kHz, TJ = 25°C
Vd
Dropout voltage
TJ = 25°C
Isc
Short circuit current
Iscp
Short circuit peak current
14/31
Typ.
VI = 27 to 38 V, IO = 200 mA, TJ = 25°C
Output voltage drift
SVR
Min.
mA
mA
-1.2
50
mV/°C
dB
170
µV
2
V
VI = 35 V, TJ = 25°C
240
mA
TJ = 25°C
700
mA
Doc ID 2147 Rev 13
L78MxxAB, L78MxxAC
Typical performance
6
Typical performance
Figure 8.
Dropout voltage vs. junction temp. Figure 9.
Dropout characteristics
Figure 10. Peak output current vs. inputoutput differential voltage
Figure 11. Output voltage vs. junction
temperature
Figure 12. Supply voltage rejection vs.
frequency
Figure 13. Quiescent current vs. junction
temperature
Doc ID 2147 Rev 13
15/31
Typical performance
L78MxxAB, L78MxxAC
Figure 14. Load transient response
Figure 15. Line transient response
Figure 16. Quiescent current vs. input voltage
16/31
Doc ID 2147 Rev 13
L78MxxAB, L78MxxAC
Applications information
7
Applications information
7.1
Design considerations
The L78MxxA series of fixed voltage regulators are designed with thermal overload
protection that shuts down the circuit when subjected to an excessive power overload
condition, internal short-circuit protection that limits the maximum current the circuit will
pass, and output transistor safe-area compensation that reduces the output short-circuit as
the voltage across the pass transistor is increased. In many low current applications,
compensation capacitors are not required. However, it is recommended that the regulator
input be bypassed with a capacitor if the regulator is connected to the power supply filter
with long wire lengths, or if the output load capacitance is large. An input bypass capacitor
should be selected to provide good high-frequency characteristics to insure stable operation
under all load conditions. A 0.33 µF or larger tantalum, mylar, or other capacitor having low
internal impedance at high frequencies should be chosen. The bypass capacitor should be
mounted with the shortest possible leads directly across the regulators input terminals.
Normally good construction techniques should be used to minimize ground loops and lead
resistance drops since the regulator has no external sense lead.
Figure 17. Current regulator
IO = VXX/R1+Id
Figure 18. Adjustable output regulator
VO = 7.0 V to 20 V
VI - VO ≥ 2.0 V
Doc ID 2147 Rev 13
17/31
Applications information
L78MxxAB, L78MxxAC
Figure 19. Current boost regulator
VBEQ1
R1 = ______________
IREQ-(IQ1/bQ1)
VBEQ1
IO = IREG + Q1 (IREG ______)
R1
Figure 20. Short-circuit protection
Note:
18/31
The circuit of Figure 19 can be modified to provide supply protection against short-circuits
by adding a short-circuit sense resistor, RSC, and an additional PNP transistor. The current
sensing PNP must be able to handle the short-circuit current of the three-terminal regulator.
Therefore, a four ampere plastic power transistor is specified.
Doc ID 2147 Rev 13
L78MxxAB, L78MxxAC
8
Package mechanical data
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com. ECOPACK
is an ST trademark.
Table 12.
TO-220 mechanical data
Type STD - ST Dual Gauge
Type STD - ST Single Gauge
mm.
mm.
Dim.
Min.
Max.
Min.
Typ.
Max.
A
4.40
4.60
4.40
4.60
b
0.61
0.88
0.61
0.88
b1
1.14
1.70
1.14
1.70
c
0.48
0.70
0.48
0.70
D
15.25
15.75
15.25
15.75
D1
Note:
Typ.
1.27
E
10.00
10.40
10.00
10.40
e
2.40
2.70
2.40
2.70
e1
4.95
5.15
4.95
5.15
F
1.23
1.32
0.51
0.60
H1
6.20
6.60
6.20
6.60
J1
2.40
2.72
2.40
2.72
L
13.00
14.00
13.00
14.00
L1
3.50
3.93
3.50
3.93
L20
16.40
16.40
L30
28.90
28.90
∅P
3.75
3.85
3.75
3.85
Q
2.65
2.95
2.65
2.95
In spite of some difference in tolerances, the packages are compatible.
Doc ID 2147 Rev 13
19/31
Package mechanical data
L78MxxAB, L78MxxAC
Figure 21. TO-220 (type STD-ST Dual Gauge) package dimensions
0015988_S
Note:
20/31
1
Maximum resin gate protrusion: 0.5 mm.
2
Resin gate position is accepted in each of the two positions shown on the drawing, or their
symmetrical.
Doc ID 2147 Rev 13
L78MxxAB, L78MxxAC
Package mechanical data
Figure 22. TO-220 (type STD-ST Single Gauge) package dimensions
8174627_B
Doc ID 2147 Rev 13
21/31
Package mechanical data
L78MxxAB, L78MxxAC
Figure 23. TO-220 Dual Gauge (mm.) tube dimensions
Figure 24. Tube for TO-220 Single Gauge (mm.) tube dimensions
22/31
Doc ID 2147 Rev 13
L78MxxAB, L78MxxAC
Package mechanical data
Figure 25. DPAK type STD-ST package dimensions
0068772_G
Doc ID 2147 Rev 13
23/31
Package mechanical data
L78MxxAB, L78MxxAC
Figure 26. DPAK type FUJITSU-subcon package dimensions
0068772_G
24/31
Doc ID 2147 Rev 13
L78MxxAB, L78MxxAC
Package mechanical data
Figure 27. DPAK type IDS-subcon package dimensions
0068772_G
Doc ID 2147 Rev 13
25/31
Package mechanical data
Table 13.
L78MxxAB, L78MxxAC
DPAK mechanical data
Dim.
Min.
Type STD-ST
Type Fujitsu-subcon.
Type IDS-subcon.
mm.
mm.
mm.
Typ.
Max.
Min.
Typ.
Max.
Min.
Typ.
Max.
2.30
2.35
2.19
2.38
A
2.20
2.40
2.25
A1
0.90
1.10
0.96
1.06
0.89
1.14
A2
0.03
0.23
0
0.10
0.03
0.23
b
0.64
0.90
0.76
0.86
0.64
0.88
b4
5.20
5.40
5.28
5.38
5.21
5.46
c
0.45
0.60
0.46
0.56
0.46
0.58
c2
0.48
0.60
0.46
0.56
0.46
0.58
D
6.00
6.20
6.05
6.15
5.97
6.22
5.27
5.47
D1
E
5.10
6.40
6.60
E1
4.70
e
2.28
2.23
4.40
4.60
H
9.35
10.10
L
1.00
2.80
L2
0.80
L4
0.60
R
V2
Note:
26/31
6.65
6.35
1.00
2.28
2.33
2.28
4.51
4.61
10.42
10.30
9.40
1.40
1.60
0.90
2.50
2.65
1.03
1.13
0.89
1.27
0.70
0.90
0.64
1.02
0.40
8°
6.73
4.70
9.90
0.20
0°
6.60
4.77
e1
L1
6.55
5.20
0°
0.20
8°
0°
The DPAK package coming from the two subcontractors (Fujitsu and IDS) are fully
compatible with the ST's package suggested footprint.
Doc ID 2147 Rev 13
8°
L78MxxAB, L78MxxAC
Package mechanical data
Figure 28. DPAK footprint recommended data
Table 14.
Footprint data
Values
Dim.
mm.
inch.
A
6.70
0.264
B
6.70
0.64
C
1.8
0.070
D
3.0
0.118
E
1.60
0.063
F
2.30
0.091
G
2.30
0.091
Doc ID 2147 Rev 13
27/31
Package mechanical data
L78MxxAB, L78MxxAC
Tape & reel DPAK-PPAK mechanical data
mm.
inch.
Dim.
Min.
Typ.
A
Min.
Typ.
330
13.0
13.2
Max.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
28/31
Max.
0.504
0.512
22.4
0.519
0.882
Ao
6.80
6.90
7.00
0.268
0.272
0.2.76
Bo
10.40
10.50
10.60
0.409
0.413
0.417
Ko
2.55
2.65
2.75
0.100
0.104
0.105
Po
3.9
4.0
4.1
0.153
0.157
0.161
P
7.9
8.0
8.1
0.311
0.315
0.319
Doc ID 2147 Rev 13
L78MxxAB, L78MxxAC
Order codes
9
Order codes
Table 15.
Order codes
Packaging
Part numbers
TO-220
L78M05ABV
L78M05AB
L78M05ABV-DG
DPAK
Output voltages
L78M05ABDT-TR
5V
(1)
5V
L78M05AC
L78M05ACDT-TR
5V
L78M06AB
L78M06ABDT-TR
6V
L78M08AB
L78M08ABDT-TR
8V
L78M09AB
L78M09ABDT-TR
9V
L78M10AB
L78M10ABDT-TR
10 V
L78M12ABDT-TR
12 V
L78M12ACDT-TR
12 V
L78M15ABDT-TR
15 V
L78M12AB
L78M12ABV
L78M12AC
L78M15ABV
L78M15AB
L78M15ABV-DG
(1)
15 V
L78M24AB
L78M24ABDT-TR
24 V
L78M24AC
L78M24ACDT-TR
24 V
1. TO-220 Dual Gauge frame
Doc ID 2147 Rev 13
29/31
Revision history
L78MxxAB, L78MxxAC
10
Revision history
Table 16.
Document revision history
Date
Revision
30-Aug-2006
3
Order codes updated.
05-Oct-2006
4
DPAK mechanical data updated and add footprint data.
10-Dec-2007
5
Modified: Table 15.
20-Feb-2008
6
Modified: Table 15 on page 29.
15-Jul-2008
7
Modified: Table 15 on page 29.
15-Apr-2009
8
Modified: Figure 9 on page 15 and Figure 15 on page 16.
28-Jul-2009
9
Modified: Table 15 on page 29.
11-Nov-2010
10
Modified: RthJC value for TO-220 Table 3 on page 5.
09-Feb-2012
11
Added: order code L78M15ABV-DG Table 15 on page 29.
09-Mar-2012
12
Added: order code L78M05ABV-DG Table 15 on page 29.
31-May-2012
13
Added: Table 12 on page 19, Figure 21 on page 20, Figure 22 on page 21,
Figure 23 and Figure 24 on page 22.
30/31
Changes
Doc ID 2147 Rev 13
L78MxxAB, L78MxxAC
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 2147 Rev 13
31/31
Similar pages