IDT IDTQS3253QG8 Quickswitch products high-speed cmos quickswitch dual 4:1 mux/demux Datasheet

IDTQS3253
HIGH-SPEED CMOS QUICKSWITCH DUAL 4:1 MUX/DEMUX
INDUSTRIAL TEMPERATURE RANGE
QUICKSWITCH® PRODUCTS
HIGH-SPEED CMOS
QUICKSWITCH
DUAL 4:1 MUX/DEMUX
DESCRIPTION:
FEATURES:
•
•
•
•
•
•
•
IDTQS3253
The QS3253 is a high-speed CMOS TTL-compatible dual 4:1 multiplexer/demultiplexer with 3-state outputs. The QS3253 is function and
pinout compatible version of the 74F253, 74FCT253, and the 74ALS/AS/
LS253 dual 4:1 multiplexers. The low ON resistance of the QS3253 allows
inputs to be connected to outputs without adding propagation delay and
without generating additional ground bounce noise.
Mux/Demux devices provide an order of magnitude faster speed than
equivalent logic devices.
The QS3253 is characterized for operation at -40°C to +85°C.
Enhanced N channel FET with no inherent diode to Vcc
Ω bidirectional switches connect inputs to outputs
5Ω
Pin compatible with the 74F253, 74FCT253, and 74FCT253T
Zero propagation delay, zero ground bounce
Undershoot clamp diodes on all switch and control inputs
TTL-compatible control inputs
Available in QSOP and S1 packages
APPLICATIONS:
•
•
•
•
•
•
Logic replacement
Video, audio, graphics switching, muxing
Hot-swapping, hot-docking
Voltage translation (5V to 3.3V)
Power conservation
Bus funneling
FUNCTIONAL BLOCK DIAGRAM
S0
S1
EA
EB
I0A
I1A
I2A
YA
I3A
I0B
I1B
I2B
YB
I3B
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
c
2011 Integrated Device Technology, Inc.
FEBRUARY 2006
1
DSC-5755/7
IDTQS3253
HIGH-SPEED CMOS QUICKSWITCH DUAL 4:1 MUX/DEMUX
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
EA
ABSOLUTE MAXIMUM RATINGS(1)
16
1
VCC
I3A
3
14
EB
S0
I2A
4
13
I3B
I1A
5
12
I2B
I0A
6
11
I1B
YA
7
10
I0B
GND
8
9
YB
S1
15
2
Symbol
Description
VTERM(2)
Max
Unit
VTERM(3)
Supply Voltage to Ground
–0.5 to +7
V
DC Switch Voltage Vs
–0.5 to +7
V
VTERM(3)
DC Input Voltage VIN
–0.5 to +7
V
VAC
AC Input Voltage (pulse width ≤ 20ns)
–3
V
IOUT
DC Output Current
120
mA
PMAX
Maximum Power Dissipation (TA = 85°C)
0.5
W
TSTG
Storage Temperature
–65 to +150
°C
NOTE:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. Vcc terminals.
3. All terminals except Vcc.
CAPACITANCE (TA = +25°C, f = 1MHz, VIN = 0V, VOUT = 0V)
QSOP/ S1
TOP VIEW
Pins
Typ.
Max. (1)
Unit
Control Inputs
4
5
pF
5
14
7
16
pF
Quickswitch Channels
(Switch OFF)
Demux
Mux
NOTE:
1. This parameter is guaranteed but not production tested.
PIN DESCRIPTION
Pin Names
I/O
Description
Ixx
I
Data Inputs
S0 - S2
I
Select Inputs
EA, EB
I
Enable Input
YA, YB
O
Data Output
FUNCTION TABLE(1)
Enable
Select
EA
EB
S1
S0
YA
YB
Function
H
X
X
X
Hi-Z
X
Disconnected
X
H
X
X
X
Hi-Z
Disconnected
L
L
L
L
I0A
I0B
S1 - 0 = 0
L
L
L
H
I1A
I1B
S1 - 0 = 1
L
L
H
L
I2A
I2B
S1 - 0 = 2
L
L
H
H
I3A
I3B
S1 - 0 = 3
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don’t Care
Z = High-Impedence
2
Outputs
IDTQS3253
HIGH-SPEED CMOS QUICKSWITCH DUAL 4:1 MUX/DEMUX
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: TA = –40°C to +85°C, VCC = 5.0V ±5%
Symbol
Parameter
Test Conditions
Min.
Typ.(1)
Max.
Unit
2
—
—
V
VIH
Input HIGH Level
Guaranteed Logic HIGH for Control Pins
VIL
Input LOW Level
Guaranteed Logic LOW for Control Pins
—
—
0.8
V
IIN
Input LeakageCurrent (Control Inputs)
0V ≤ VIN ≤ VCC
—
—
±1
μA
IOZ
Off-State Output Current (Hi-Z)
0V ≤ VOUT ≤ VCC
—
—
±1
μA
RON
Switch ON Resistance
Pass Voltage(2)
—
—
3.7
5
10
4
7
15
4.2
Ω
VP
VCC = Min., VIN = 0V, ION = 30mA
VCC = Min., VIN = 2.4V, ION =15mA
VIN = VCC = 5V, IOUT = -5μA
NOTES:
1. Typical values are at VCC = 5.0V, TA = 25°C.
2. Pass Voltage is guaranteed but not production tested.
TYPICAL ON RESISTANCE vs VIN AT VCC = 5V
16
R ON
(ohms)
14
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
V IN
(Volts)
3
2.5
3.0
3.5
V
IDTQS3253
HIGH-SPEED CMOS QUICKSWITCH DUAL 4:1 MUX/DEMUX
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
Test Conditions(1)
Parameter
Max.
Unit
ICCQ
Quiescent Power Supply Current
VCC = Max., VIN = GND or Vcc, f = 0
3
μA
ΔICC
Power Supply Current per Control Input HIGH (2)
VCC = Max., VIN = 3.4V, f = 0
1.5
mA
ICCD
Dynamic Power Supply Current per MHz(3)
VCC = Max., I and Y pins open
0.25
mA/MHz
Control Inputs Toggling at 50% Duty Cycle
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per TLL driven input (VIN = 3.4V, control inputs only). I and Y pins do not contribute to ΔIcc.
3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The I and Y inputs generate no significant
AC or DC currents as they transition. This parameter is guaranteed but not production tested.
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
TA = -40°C to +85°C, VCC = 5.0V ± 5%;
CLOAD = 50pF, RLOAD = 500Ω unless otherwise noted.
Symbol
Parameter
tPLH
Data Propagation Delay (2,3)
tPHL
Ix to Y
tPZL
Switch Turn-on Delay
tPZH
Sx to Y
tPZL
Switch Turn-on Delay
tPZH
Ex to Y
tPLZ
Switch Turn-off Delay (2)
tPHZ
Ex to Y, Sx to Y
Min. (1)
Typ.
Max.
Unit
—
—
0.25
ns
0.5
—
6.6
ns
0.5
—
6
ns
0.5
—
6
ns
NOTES:
1. Minimums are guaranteed but not production tested.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone
is of the order of 0.25ns for CL = 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to
the system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load
on the driven side.
4
IDTQS3253
HIGH-SPEED CMOS QUICKSWITCH DUAL 4:1 MUX/DEMUX
INDUSTRIAL TEMPERATURE RANGE
ORDERING INFORMATION
QS
XXXXX
Device Type
XX
Package
X
Blank
8
Tube or Tray
Tape and Reel
QG
S1G
Quarter Size Outline Package - Green
Small Outline IC - Green
3253
High Speed CMOS Quickswitch Dual 4:1
Mux/Demux
Datasheet Document History
02/14/2011
Pg. 5
Updated the ordering information by removing the "IDT" notation, non RoHS part and by adding
Tape and Reel information.
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
5
for Tech Support:
[email protected]
Similar pages