Renesas EL5825IRZ-T7 8-channel tft-lcd reference voltage generator Datasheet

DATASHEET
EL5825
FN7005
Rev 4.00
June 24, 2005
8-Channel TFT-LCD Reference Voltage Generator
The EL5825 is designed to produce the reference voltages
required in TFT-LCD applications. Each output is
programmed to the required voltage with 10 bits of
resolution. Reference pins determine the high and low
voltages of the output range, which are capable of swinging
to either supply rail. Programming of each output is
performed using the serial interface. A serial out pin enables
daisy chaining of multiple devices.
Features
A number of the EL5825 can be stacked for applications
requiring more than 8 outputs. The reference inputs can be
tied to the rails, enabling each part to output the full voltage
range, or alternatively, they can be connected to external
resistors to split the output range and enable finer
resolutions of the outputs.
• Rail-to-rail capability
The EL5825 has 8 outputs and is available in both the 24-pin
TSSOP and the 24-pin QFN packages. It is specified for
operation over the full -40°C to +85°C temperature range.
• Reference voltage generators
• Supply voltage of 4.5V to 16.5V
• Digital supply 3.3V to 5V
• Low supply current of 8mA
• Pb-Free plus anneal available (RoHS compliant)
Applications
• TFT-LCD drive circuits
Pinouts
MDP0046
EL5825IL-T13
24-Pin QFN
13”
MDP0046
EL5825ILZ
(See Note)
24-Pin QFN
(Pb-free)
-
MDP0046
EL5825ILZ-T7
(See Note)
24-Pin QFN
(Pb-free)
7”
MDP0046
EL5825ILZ-T13
(See Note)
24-Pin QFN
(Pb-free)
13”
MDP0046
EL5825IR
24-Pin TSSOP
-
MDP0044
EL5825IR-T7
24-Pin TSSOP
7”
MDP0044
EL5825IR-T13
24-Pin TSSOP
13”
MDP0044
EL5825IRZ
(See Note)
24-Pin TSSOP
(Pb-free)
-
MDP0044
EL5825IRZ-T7
(See Note)
24-Pin TSSOP
(Pb-free)
7”
MDP0044
EL5825IRZ-T13 24-Pin TSSOP
(See Note)
(Pb-free)
13”
MDP0044
2 SDO
ENA 23
3 OSC
OUTA 22
4 VSD
OUTB 21
5 NC
OUTC 20
6 VS
OUTD 19
7 REFH
GND 18
8 REFL
OUTE 17
9 GND
OUTF 16
10 NC
OUTG 15
11 CAP
OUTH 14
12 NC
20 OUTA
7”
OSC 1
19 OUTB
VSD 2
18 OUTC
NC 3
17 OUTD
THERMAL
PAD
VS 4
Thermal Pad
16 GND
REFH 5
15 OUTE
REFL 6
14 OUTF
GND 7
13 OUTG
OUTH 12
24-Pin QFN
SDI 24
21 ENA
EL5825IL-T7
1 SCLK
NC 11
MDP0046
22 SDI
-
NC 10
24-Pin QFN
NC 9
EL5825IL
24 SDO
TAPE & REEL PKG. DWG. #
23 SCLK
EL5825
(24-PIN QFN)
TOP VIEW
CAP 8
PACKAGE
• Accuracy of ±0.1%
EL5825
(24-PIN TSSOP)
TOP VIEW
Ordering Information
PART
NUMBER
• 8-channel reference outputs
NC 13
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100% matte
tin plate termination finish, which are RoHS compliant and compatible
with both SnPb and Pb-free soldering operations. Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
FN7005 Rev 4.00
June 24, 2005
Page 1 of 12
EL5825
Absolute Maximum Ratings (TA = 25°C)
Supply Voltage between VS and GND. . . . . . . . . . . . . . . . . . . .+18V
Supply Voltage between VSD and GND . . . . . . . VS and +7V (max)
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 30mA
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . 125°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are
at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Electrical Specifications
PARAMETER
VS = 15V, VSD = 5V, VREFH = 13V, VREFL = 2V, RL = 1.5k and CL = 200pF to 0V, TA = 25°C, unless
otherwise specified.
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
7.6
9
mA
0.17
0.35
mA
50
150
mV
SUPPLY
IS
Supply Current
ISD
Digital Supply Current
No load
ANALOG
VOL
Output Swing Low
Sinking 5mA (VREFH = 15V, VREFL = 0)
VOH
Output Swing High
Sourcing 5mA (VREFH = 15V, VREFL = 0)
ISC
Short Circuit Current
PSRR
Power Supply Rejection Ratio
tD
14.85
14.95
V
RL = 10
100
140
mA
VS+ is moved from 14V to 16V
45
60
dB
Program to Out Delay
4
ms
VAC
Accuracy
20
mV
VDROOP
Droop Voltage
1
RINH
Input Resistance @ VREFH, VREFL
34
REG
Load Regulation
BG
Band Gap
IOUT = 5mA step
1.1
2
mV/ms
k
0.5
1.5
mV/mA
1.3
1.6
V
DIGITAL
VIH
Logic 1 Input Voltage
VIL
Logic 0 Input Voltage
FCLK
Clock Frequency
tS
Setup Time
20
ns
tH
Hold Time
20
ns
tLC
Load to Clock Time
20
ns
tCE
Clock to Load Line
20
ns
tDCO
Clock to Out Delay Time
10
ns
RSDIN
SDIN Input Resistance
1
G
FN7005 Rev 4.00
June 24, 2005
VSD20%
Negative edge of SCLK
V
20%*
VSD
V
5
MHz
Page 2 of 12
EL5825
Pin Descriptions
24-PIN QFN
24-PIN TSSOP
PIN NAME
PIN TYPE
1
3
OSC
IP/OP
Oscillator pin for synchronizing multiple chips
2
4
VSD
Power
Positive power supply for digital circuits (3.3V - 5V)
3
5
NC
4
6
VS
Power
5
7
REFH
Analog Input
High reference voltage
6
8
REFL
Analog Input
Low reference voltage
7
9
GND
Power
Ground
8
11
CAP
Analog
Decoupling capacitor for internal reference generator, 0.1µF
9
10
NC
Not connected
10
12
NC
Not connected
11
13
NC
Not connected
12
14
OUTH
Analog Output
Channel H programmable output voltage
13
15
OUTG
Analog Output
Channel G programmable output voltage
14
16
OUTF
Analog Output
Channel F programmable output voltage
15
17
OUTE
Analog Output
Channel E programmable output voltage
16
18
GND
Power
17
19
OUTD
Analog Output
Channel D programmable output voltage
18
20
OUTC
Analog Output
Channel C programmable output voltage
19
21
OUTB
Analog Output
Channel B programmable output voltage
20
22
OUTA
Analog Output
Channel A programmable output voltage
21
23
ENA
Logic Input
Chip select, low enables data input to logic
22
24
SDI
Logic Input
Serial data input
23
1
SCLK
Logic Input
Serial data clock
24
2
SDO
Logic Output
Serial data output
FN7005 Rev 4.00
June 24, 2005
PIN DESCRIPTION
Not connected
Positive supply voltage for analog circuits
Ground
Page 3 of 12
EL5825
INPUT CODE
0.3
VSD (V)
180
160
0.2
140
120
0.1
ISD (nA)
DIFFERENTIAL NONLINEARITY (LSB)
Typical Performance Curves
0
100
80
60
-0.1
VS=15V
VSD=5V
VREFH=13V
VREFL=2V
-0.2
-0.3
10
210
410
610
810
40
20
0
3
1010
FIGURE 1. DIFFERENTIAL NONLINEARITY vs CODE
5
0mA
6.8
5.5
5mA/DIV
5mA
6.6
IS (mA)
4.5
VS=VREFH=15V
M=400ns/DIV
VOUT=0V
7
4
FIGURE 2. DIGITAL SUPPLY CURRENT vs DIGITAL SUPPLY
VOLTAGE
VS (V)
7.2
3.5
CL=4.7nF
RS=20
6.4
6.2
5V
CL=1nF
RS=20
6
5.8
200mV/DIV
CL=180pF
5.6
4
6
8
10
12
14
16
18
FIGURE 3. SUPPLY CURRENT vs SUPPLY VOLTAGE
FIGURE 4. TRANSIENT LOAD REGULATION (SOURCING)
VS=VREFH=15V
M=400ns/DIV
M=200µs/DIV
5mA
SCLK
0mA
CL=1nF
RS=20
SDA
ENA
CL=4.7nF
RS=20
CL=180pF
FIGURE 5. TRANSIENT LOAD REGULATION (SINKING)
FN7005 Rev 4.00
June 24, 2005
OUTA
FIGURE 6. LARGE SIGNAL RESPONSE (RISING FROM 0V
TO 8V)
Page 4 of 12
EL5825
Typical Performance Curves
(Continued)
M=200µs/div
SCLK
SDA
ENA
OUTA
FIGURE 7. SMALL SIGNAL RESPONSE (FALLING FROM 200mV TO 100mV)
0.9
0.8
1.176W
1.2
1

JA
0.8
0.6
POWER DISSIPATION (W)
POWER DISSIPATION (W)
1.4
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
TS
S
OP
24
=8
5°
C/
W
0.4
0.2
781mW
0.7
0.6

JA
0.5
0.4
0.3
0.2
0.1
0
0
0
25
50
75 85
100
0
125
25
50
75 85
100
125
AMBIENT TEMPERATURE (°C)
AMBIENT TEMPERATURE (°C)
FIGURE 8. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
FIGURE 9. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD - QFN EXPOSED
DIEPAD SOLDERED TO PCB PER JESD51-5
JEDEC JESD51-3 AND SEMI G42-88 (SINGLE
LAYER) TEST BOARD
0.8
3
2.703W

1.5
FN
24
37
°C
/W
1
0.5
0.5
A
JA
=
714mW
24
/W
FN
°C
40
=1
2
Q
0.6
Q
POWER DISSIPATION (W)
0.7
2.5
J
POWER DISSIPATION (W)
TS
SO
P2
=1
4
28
°C
/W
0.4
0.3
0.2
0.1
0
0
0
25
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
FIGURE 10. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
FN7005 Rev 4.00
June 24, 2005
0
25
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
FIGURE 11. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
Page 5 of 12
EL5825
Product Description
The EL5825 provides a versatile method of providing the
reference voltages that are used in setting the transfer
characteristics of LCD display panels.
The V/T (Voltage/Transmission) curve of the LCD panel
requires that a correction is applied to make it linear;
however, if the panel is to be used in more than one
application, the final curve may differ for different
applications.
By using the EL5825, this curve can be changed to optimize
its characteristics according to the required application of the
display product.
Each of the reference voltage outputs can be set with a
10-bit resolution. These outputs are available to within
100mV of the power rails of the EL5825.
allocated to the following functions (also refer to the Control
Bits Logic Table)
• Bit 15 is always set to a zero
• Bit 14 controls the source of the clock, see the next
section for details
• Bits 13 through 10 select the channel to be written to,
these are binary coded with channel A = 0, and channel
H=7
• The 10-bit data is on bits 9 through 0. Some examples of
data words are shown in the table of Serial Programming
Examples
TABLE 1. CONTROL BITS LOGIC TABLE
BIT
NAME
DESCRIPTION
B15
Test
As all of the output buffers are identical, it is also possible to
use the EL5825 for applications other than LCDs where 8
voltage references are required that can be set to a 10-bit
accuracy.
B14
Oscillator
B13
A3
Channel Address (don’t care)
B12
A2
Channel Address
Serial Interface
B11
A1
Channel Address
The EL5825 is programmed through a three-wire serial
interface. The start and stop conditions are defined by the
ENA signal. While the ENA is low, the data on the SDI (serial
data input) pin is shifted into the 16-bit shift register on the
positive edge of the SCLK (serial clock) signal. The MSB (bit
15) is loaded first and the LSB (bit 0) is loaded last (see
Table 1). After the full 16-bit data has been loaded, the ENA
is pulled high and the addressed output channel is updated.
The SCLK is disabled internally when the ENA is high. The
SCLK must be low before the ENA is pulled low.
B10
A0
Channel Address
B9
D9
Data
B8
D8
Data
B7
D7
Data
B6
D6
Data
B5
D5
Data
B4
D4
Data
To facilitate the system designs that use multiple EL5825
chips, a buffered serial output of the shift register (SDO pin)
is available. Data appears on the SDO pin at the 16th falling
SCLK edge after being applied to the SDI pin.
B3
D3
Data
B2
D2
Data
B1
D1
Data
To control the multiple EL5825 chips from a single three-wire
serial port, just connect the ENA pins and the SCLK pins
together, connect the SDO pin to the SDI pin on the next
chip. While the ENA is held low, the 16m-bit data is loaded to
the SDI input of the first chip. The first 16-bit data will go to
the last chip and the last 16-bit data will go to the first chip.
While the ENA is held high, all addressed outputs will be
updated simultaneously.
B0
D0
Data
Always 0
0 = Internal, 1 = External
The Serial Timing Diagram and parameters table show the
timing requirements for three-wire signals.
The serial data has a minimum length of 16 bits, the MSB
(most significant bit) is the first bit in the signal. The bits are
FN7005 Rev 4.00
June 24, 2005
Page 6 of 12
EL5825
Serial Timing Diagram
ENA
tHE
tSE
T
tr
tf
tHE
tSE
SCLK
tSD
SDI
tHD
B15
tw
B14
B13
B12-B2
B1
B0
t
MSB
LSB
Load MSB first, LSB last
TABLE 2. SERIAL TIMING PARAMETERS
PARAMETER
EXAMPLE
DESCRIPTION
T
200ns
Clock Period
tr/tf
0.05 * T
Clock Rise/Fall Time
tHE
10ns
ENA Hold Time
tSE
10ns
ENA Setup Time
tHD
10ns
Data Hold Time
tSD
10ns
Data Setup Time
tW
0.50 * T
Clock Pulse Width
TABLE 3. SERIAL PROGRAMMING EXAMPLES
CONTROL
CHANNEL ADDRESS
C1
C0
A3
A2
A1
A0
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
0
X
0
0
0
0
0
0
0
0
0
0
0
0
0
Internal Oscillator, Channel A, Value = 0
0
0
X
0
0
0
1
1
1
1
1
1
1
1
1
1
Internal Oscillator, Channel A, Value = 1023
0
0
X
0
0
0
1
0
0
0
0
0
0
0
0
0
Internal Oscillator, Channel A, Value = 512
0
0
X
0
1
1
1
0
0
0
0
0
0
0
0
1
Internal Oscillator, Channel C, Value = 513
0
0
X
1
1
1
0
0
0
0
0
1
1
1
1
1
Internal Oscillator, Channel H, Value = 31
0
1
X
1
1
1
0
0
0
0
0
1
1
1
1
1
External Oscillator, Channel H, Value = 31
FN7005 Rev 4.00
June 24, 2005
DATA
CONDITION
Page 7 of 12
EL5825
Internal Refresh Clock Oscillator
The EL5825 requires an internal clock or external clock to
refresh its outputs. The outputs are refreshed at the falling
OSC clock edges. The output refreshed switches open at
the rising edges of the OSC clock. The driving load shouldn’t
be changed at the rising edges of the OSC clock. Otherwise,
it will generate a voltage error at the outputs. This clock may
be input or output via the clock pin labeled OSC. The internal
clock is provided by an internal oscillator running at
approximately 25kHz and can be output to the OSC pin. In a
multiple chip system, if the driving loads are stable, one chip
may be programmed to use the internal oscillator; then the
OSC pin will output the clock from the internal oscillator.
Subsequent chips may have the OSC pin connected to this
clock source. In these chips, the program will set them to
external OSC Mode by setting bit 14 to 1. See the control
bits logic table and serial programming example for details.
For transient load application, the external clock Mode
should be used to ensure all functions are synchronized
together. The positive edge of the external clock to the OSC
pin should be timed to avoid the transient load effect. The
Application Drawing on page 10 shows the LCD H rate
signal used, here the positive clock edge is timed to avoid
the transient load of the column driver circuits.
After power on, the chip will start with the internal oscillator
mode. At this time, the OSC pin will be in a high impedance
condition to prevent contention. After programming the
oscillator with bit 14, the pin will be set to the appropriate
mode.
Transfer Function
The transfer function is:
data
V OUT  IDEAL  = V REFL + -------------   V REFH - V REFL 
1024
where data is the decimal value of the 10-bit data binary
input code.
The output voltages from the EL5825 will be derived from
the reference voltages present at the VREFL and VREFH
pins. The impedance between those two pins is about 32k.
Care should be taken that the system design holds these
two reference voltages within the limits of the power rails of
the EL5825. GND < VREFH  VS and GND  VREFL 
VREFH.
In some LCD applications that require more than 8 channels,
the system can be designed such that one EL5825 will
provide the Gamma correction voltages that are more
positive than the VCOM potential. The second EL5825 can
provide the Gamma correction voltage more negative than
the VCOM potential. The Application Drawing on page 10
shows a system connected in this way.
Block Diagram
REFERENCE HIGH
OUTA
OUTB
OUTC
OUTD
EIGHT
CHANNEL
REGISTERS
VOLTAGE
SOURCES
OUTE
OUTF
OUTG
OUTH
REFERENCE LOW
CAP
SERIAL DATA OUTPUT
SERIAL DATA INPUT
SERIAL CLOCK
CONTROL IF
ENABLE
OSCILLATOR INPUT/OUTPUT3
FN7005 Rev 4.00
June 24, 2005
Page 8 of 12
EL5825
Channel Outputs
Where:
Each of the channel outputs has a rail-to-rail buffer. This
enables all channels to have the capability to drive to within
100mV of the power rails, (see Electrical Characteristics for
details).
• i = 1 to total 8
When driving large capacitive loads, a series resistor should
be placed in series with the output. (Usually between 5 and
50).
Each of the channels is updated on a continuous cycle, the
time for the new data to appear at a specific output will
depend on the exact timing relationship of the incoming data
to this cycle.
The best-case scenario is when the data has just been
captured and then passed on to the output stage
immediately; this can be as short as 40µs. In the worst-case
scenario this will be 320µs, when the data has just missed
the cycle.
When a large change in output voltage is required, the
change will occur in 2 volt steps, thus the requisite number of
timing cycles will be added to the overall update time. This
means that a large change of 16 volts can take between 2.56
milliseconds and 3 milliseconds depending on the absolute
timing relative to the update cycle.
Power Dissipation
With the 30mA maximum continues output drive capability
for each channel, it is possible to exceed the 125°C absolute
maximum junction temperature. Therefore, it is important to
calculate the maximum junction temperature for the
application to determine if load conditions need to be
modified for the part to remain in the safe operation.
The maximum power dissipation allowed in a package is
determined according to:
T JMAX - T AMAX
P DMAX = -------------------------------------------- JA
• VS = Supply voltage
• IS = Quiescent current
• VOUTi = Output voltage of the i channel
• ILOADi = Load current of the i channel
By setting the two PDMAX equations equal to each other, We
can solve for the RLOAD's to avoid the device overheat. The
package power dissipation curves provide a convenient way
to see if the device will overheat.
Power Supply Bypassing and Printed Circuit
Board Layout
Good printed circuit board layout is necessary for optimum
performance. A low impedance and clean analog ground
plane should be used for the EL5825. The traces from the
two ground pins to the ground plane must be very short. The
thermal pad of the EL5825 should be connected to the
analog ground plane. Lead length should be as short as
possible and all power supply pins must be well bypassed. A
0.1µF ceramic capacitor must be place very close to the VS,
VREFH, VREFL, and CAP pins. A 4.7µF local bypass
tantalum capacitor should be placed to the VS, VREFH, and
VREFL pins.
Application Using the EL5825
In the application drawing, the schematic shows the
interconnect of a pair of EL5825 chips connected to give 8
gamma corrected voltages above the VCOM voltage, and 8
gamma corrected voltages below the VCOM voltage.
By using the serial data out pin, it is possible to daisy chain
(cascade) the two chips. In this mode the micro-controller
will send a 32-bit word that will update both the upper and
lower references voltages in one operation. See Application
Drawing 1 for details.
where:
• TJMAX = Maximum junction temperature
• TAMAX = Maximum ambient temperature
• JA = Thermal resistance of the package
• PDMAX = Maximum power dissipation in the package
The maximum power dissipation actually produced by the IC
is the total quiescent supply current times the total power
supply voltage and plus the power in the IC due to the loads.
P DMAX = V S  I S +    V S - V OUT i   I LOAD i 
when sourcing, and:
P DMAX = V S  I S +   V OUT i  I LOAD i 
when sinking.
FN7005 Rev 4.00
June 24, 2005
Page 9 of 12
EL5825
Application Drawing
HIGH
REFERENCE
VOLTAGE
EL5825
+10V
REFH
OUTA
VS
OUTB
VSD
OUTC
0.1µF
+12V
COLUMN
(SOURCE)
DRIVER
0.1µF
MICROCONTROLLER
+5V
LCD PANEL
0.1µF
SERIAL DATA
SDI
SERIAL DATA CLOCK
SCLK
OUTE
ENABLE
ENA
SERIAL DATA
LCD TIMING
CONTROLLER
OUTD
SDO
OUTF
OSC
HORIZONTAL
RATE
CAP
OUT
0.1µF
REFL
GND
OUTH
MIDDLE REFERENCE
VOLTAGE
+5.5V
REFH
OUTA
OSC
+12V
VS
OUTB
0.1µF
+5V
VSD
OUTC
0.1µF
SERIAL DATA
SDI
SERIAL DATA CLOCK
SCLK
OUTE
ENABLE
ENA
CAP
LOW
REFERENCE
VOLTAGE
OUTD
OUTF
0.1µF
REFL
+1V
OUT
0.1µF
GND
OUTH
Serial Timing Diagram (32 bit)
FN7005 Rev 4.00
June 24, 2005
Page 10 of 12
EL5825
QFN Package Outline Drawing
FN7005 Rev 4.00
June 24, 2005
Page 11 of 12
EL5825
TSSOP Package Outline Drawing
NOTE: The package drawing shown here may not be the latest version. To check the latest revision, please refer to the Intersil website at
<http://www.intersil.com/design/packages/index.asp>
© Copyright Intersil Americas LLC 2004-2005. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN7005 Rev 4.00
June 24, 2005
Page 12 of 12
Similar pages