Maxim MAX16027 Dual-/triple-/quad-voltage, capacitor-adjustable, sequencing/supervisory circuit Datasheet

19-0525; Rev 3; 1/07
KIT
ATION
EVALU
E
L
B
AVAILA
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
The MAX16025–MAX16030 are dual-/triple-/quad-voltage monitors and sequencers that are offered in a
small TQFN package. These devices offer enormous
design flexibility as they allow fixed and adjustable
thresholds to be selected through logic inputs and provide sequence timing through small external capacitors. These versatile devices are ideal for use in a wide
variety of multivoltage applications.
As the voltage at each monitored input exceeds its
respective threshold, its corresponding output goes
high after a propagation delay or a capacitor-set time
delay. When a voltage falls below its threshold, its
respective output goes low after a propagation delay.
Each detector circuit also includes its own enable input,
allowing the power-good outputs to be shut off independently. The independent output for each detector is
available with push-pull or open-drain configuration
with the open-drain version capable of supporting voltages up to 28V, thereby allowing them to interface to
shutdown and enable inputs of various DC-DC regulators. Each detector can operate independently as four
separate supervisory circuits or can be daisy-chained
to provide controlled power-supply sequencing.
The MAX16025–MAX16030 also include a reset function that deasserts only after all of the independently
monitored voltages exceed their threshold. The reset
timeout is internally fixed or can be adjusted externally.
These devices are offered in a 4mm x 4mm TQFN
package and are fully specified from -40°C to +125°C.
Applications
Multivoltage Systems
Features
o 2.2V to 28V Operating Voltage Range
o Fixed Thresholds for 3.3V, 2.5V, 1.8V, 1.5V, and
1.2V Systems
o 1.5% Accurate Adjustable Threshold Monitors
Voltages Down to 0.5V
o 2.7% Accurate Fixed Thresholds Over
Temperature
o Fixed (140ms min)/Capacitor-Adjustable Delay
Timing
o Independent Open-Drain/Push-Pull Outputs
o Enable Inputs for Each Monitored Voltage
o 9 Logic-Selectable Threshold Options
o Manual Reset and Tolerance Select (5%/10%) Inputs
o Small, 4mm x 4mm TQFN Package
o Fully Specified from -40°C to +125°C
Ordering Information
PART*
PINPACKAGE
TEMP RANGE
PKG
CODE
MAX16025TE+
-40°C to +125°C
16 TQFN
T1644-4
MAX16026TE+
-40°C to +125°C
16 TQFN
T1644-4
MAX16027TP+
-40°C to +125°C
20 TQFN
T2044-3
MAX16028TP+
-40°C to +125°C
20 TQFN
T2044-3
MAX16029TG+
-40°C to +125°C
24 TQFN
T2444-4
MAX16030TG+
-40°C to +125°C 24 TQFN
T2444-4
+Denotes lead-free package.
*For tape and reel, add a “T” after the “+.” All tape and reel
orders are available in 2.5k increments.
Pin Configurations
Networking/Telecommunication Equipment
OUT3
OUT4
TH0
Storage Systems
OUT2
TOP VIEW
OUT1
Servers/Workstations
RESET
DC-DC Supplies
18
17
16
15
14
13
MR 19
CRESET 20
2
2 (Open-drain)
Open-drain
MAX16026
2
2 (Push-pull)
Push-pull
MAX16027
3
3 (Open-drain)
Open-drain
MAX16028
3
3 (Push-pull)
Push-pull
MAX16029
4
4 (Open-drain)
Open-drain
MAX16030
4
4 (Push-pull)
Push-pull
CDLY2 23
CDLY1 24
+
1
2
3
4
5
6
TOL
MAX16025
CDLY3 22
IN4
RESET
OUTPUT
IN3
INDEPENDENT
OUTPUTS
IN2
MONITORED
VOLTAGES
MAX16029
MAX16030
IN1
PART
CDLY4 21
VCC
Selector Guide
12
TH1
11
EN4
10
EN3
9
EN2
8
EN1
7
GND
THIN QFN
(4mm x 4mm)
Pin Configurations continued at end of data sheet.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX16025–MAX16030
General Description
MAX16025–MAX16030
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND.)
VCC .........................................................................-0.3V to +30V
EN1–EN4 ....................................................-0.3V to (VCC + 0.3V)
OUT1–OUT4 (push-pull).............................-0.3V to (VCC + 0.3V)
OUT1–OUT4 (open-drain) ......................................-0.3V to +30V
RESET (push-pull) ......................................-0.3V to (VCC + 0.3V)
RESET (open-drain) ..................................................-0.3V to 30V
IN1–IN4.......................................................-0.3V to (VCC + 0.3V)
MR, TOL, TH1, TH0 ....................................-0.3V to (VCC + 0.3V)
CDLY1–CDLY4 .........................................................-0.3V to +6V
CRESET ......................................................-0.3V to (VCC + 0.3V)
Input/Output Current (all pins)..........................................±20mA
Continuous Power Dissipation (TA = +70°C)
16-Pin TQFN (derate 25mW/°C above +70°C) ...........2000mW
20-Pin TQFN (derate 25.6mW/°C above +70°C) ........2051mW
24-Pin TQFN (derate 27.8mW/°C above +70°C) ........2222mW
Operating Temperature Range .........................-40°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Junction Temperature ......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = 2.2V to 28V, TA = -40°C to +125°C, unless otherwise specified. Typical values are at VCC = 3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
28.0
V
2.0
V
SUPPLY
Operating Voltage Range
Undervoltage Lockout
Undervoltage-Lockout Hysteresis
VCC Supply Current
VCC
(Note 2)
2.2
UVLO
(Note 2)
1.8
UVLOHYST VCC falling
ICC
All OUT_ and RESET at
logic-high (IN_ current
excluded)
1.9
50
mV
VCC = 3.3V
40
75
VCC = 12V
47
75
VCC = 28V
52
80
3.052
3.135
µA
INPUTS (IN_)
3.3V threshold, TOL = GND
IN_ Thresholds (IN_ Falling)
VTH
Adjustable Threshold (IN_
Falling)
VTH
IN_ Hysteresis (IN_ Rising)
VHYST
IN_ Input Resistance
IN_ Input Current
2
IL
2.970
3.3V threshold, TOL = VCC
2.805
2.888
2.970
2.5V threshold, TOL = GND
2.250
2.313
2.375
2.5V threshold, TOL = VCC
2.125
2.187
2.250
1.8V threshold, TOL = GND
1.620
1.665
1.710
1.8V threshold, TOL = VCC
1.530
1.575
1.620
1.5V threshold, TOL = GND
1.350
1.387
1.425
1.5V threshold, TOL = VCC
1.275
1.312
1.350
1.2V threshold, TOL = GND
1.080
1.110
1.140
1.2V threshold, TOL = VCC
1.020
1.050
1.080
TOL = GND
0.492
0.5
0.508
TOL = VCC
0.463
0.472
0.481
0.5
Fixed threshold
500
Adjustable threshold only (VIN_ = 1V)
-100
V
%
918
_______________________________________________________________________________________
V
kΩ
+100
nA
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
(VCC = 2.2V to 28V, TA = -40°C to +125°C, unless otherwise specified. Typical values are at VCC = 3.3V and TA = +25°C.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
0.465
0.5
0.535
V
nA
CRESET AND CDLY_
CRESET Threshold
VTH-RESET
CRESET rising, VCC = 3.3V
CRESET Charge Current
ICH-RESET
VCC = 3.3V
380
500
620
CDLY_ Threshold
VTH-CDLY
CDLY_ rising, VCC = 3.3V
0.95
1
1.05
V
CDLY_ Charge Current
ICH-CDLY
VCC = 3.3V
200
250
300
nA
0.4
V
DIGITAL LOGIC INPUTS (EN_, MR, TOL, TH1, TH0)
Input Low Voltage
VIL
Input High Voltage
VIH
1.4
TH1, TH0 Logic-Input Floating
V
0.6
TOL, TH1, TH0 Logic-Input
Current
VTOL, VTH1, VTH0 = GND or VCC
EN_ Input Leakage Current
VEN_ = VCC or GND
-100
MR Internal Pullup Current
VCC = 3.3V
250
-1
535
V
+1
µA
+100
nA
820
nA
OUTPUTS (OUT_, RESET)
Output Low Voltage (Open-Drain
or Push-Pull)
VOL
0.3
VCC ≥ 2.25V, ISINK = 0.5mA
0.3
VCC ≥ 4.5V, ISINK = 1mA
Output High Voltage (Push-Pull)
VOH
Output Leakage Current (OpenDrain)
ILKG
Reset Timeout Period
VCC ≥ 1.2V, ISINK = 90µA
tRP
0.35
VCC ≥ 3V, ISOURCE = 500µA
0.8 x VCC
VCC ≥ 4.5V, ISOURCE = 800µA
0.8 x VCC
V
Output not asserted low, VOUT = 28V
CRESET = VCC, VCC = 3.3V
V
1
140
CRESET open
190
0.030
260
µA
ms
TIMING
IN_ to OUT_ Propagation Delay
IN_ to RESET Propagation Delay
tDELAY+
IN_ rising, CDLY_ open
35
tDELAY-
IN_ falling, CDLY_ open
20
tRST-DELAY IN_ falling
MR Minimum Input Pulse Width
(Note 3)
EN_ or MR Glitch Rejection
EN_ to OUT_ Delay
MR to RESET Delay
35
2
µs
µs
µs
280
tOFF
From device enabled to device disabled
3
tON
From device disabled to device enabled
(CDLY_ open)
30
MR falling
3
ns
µs
µs
Note 1: Devices are production tested at TA = +25°C. Limits over temperature are guaranteed by design.
Note 2: Operating below the UVLO causes all outputs to go low. The outputs are guaranteed to be in the correct state for VCC down
to 1.2V.
Note 3: In order to guarantee an assertion, the minimum input pulse width must be greater than 2µs.
_______________________________________________________________________________________
3
MAX16025–MAX16030
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(VCC = 3.3V, TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT
vs. TEMPERATURE
45
40
50
45
VCC = 12V
40
35
35
30
30
2
10
14
18
22
26
30
TOL = GND
ADJUSTABLE THRESHOLD
-40 -25 -10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C)
TEMPERATURE (°C)
NORMALIZED ADJUSTABLE THRESHOLD
vs. TEMPERATURE
OUT_ DELAY vs. CCDLY_
4500
4000
3500
3000
2500
2000
1500
1000
500
3.3V THRESHOLD
0
1200
1100
1000
MAX16025 toc06
5000
RESET TIMEOUT PERIOD (ms)
TOL = GND
RESET TIMEOUT PERIOD
vs. CCRESET
MAX16025 toc05
TOL = VCC
900
800
700
600
500
400
300
200
100
0
0 100 200 300 400 500 600 700 800 900 1000
0 100 200 300 400 500 600 700 800 900 1000
TEMPERATURE (°C)
CCDLY_ (nF)
CCRESET (nF)
FIXED RESET TIMEOUT PERIOD
vs. TEMPERATURE
OUT_ LOW VOLTAGE
vs. SINK CURRENT
OUT_ HIGH VOLTAGE
vs. SOURCE CURRENT
3.5
0.8
MAX16025 toc09
193
1.0
MAX16025 toc08
CRESET = VCC
MAX16025 toc07
195
3.0
2.5
191
190
189
0.6
VOUT_ (V)
VOUT_ (V)
192
0.4
188
2.0
1.5
1.0
0.2
187
0.5
186
PUSH-PULL VERSIONS
0
185
-40 -25 -10 5 20 35 50 65 80 95 110 125
TEMPERATURE (°C)
4
TOL = VCC
-40 -25 -10 5 20 35 50 65 80 95 110 125
-40 -25 -10 5 20 35 50 65 80 95 110 125
194
VCC = 3.3V
1.003
1.002
1.001
1.000
0.999
0.998
0.997
0.996
0.995
0.994
0.993
0.992
0.991
0.990
SUPPLY VOLTAGE (V)
OUT_ DELAY (ms)
1.003
1.002
1.001
1.000
0.999
0.998
0.997
0.996
0.995
0.994
0.993
0.992
0.991
0.990
6
NORMALIZED THRESHOLD
55
SUPPLY CURRENT (μA)
50
MAX16026
VCC = 28V
MAX16025 toc04
SUPPLY CURRENT (μA)
55
MAX16025 toc02
MAX16026
NORMALIZED THRESHOLD
60
MAX16025 toc01
60
NORMALIZED ADJUSTABLE THRESHOLD
vs. TEMPERATURE
MAX16025 toc03
SUPPLY CURRENT
vs. SUPPLY VOLTAGE
FIXED RESET TIMEOUT PERIOD (ms)
MAX16025–MAX16030
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
0
0
1
2
3
4
5
SINK CURRENT (mA)
6
7
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
SOURCE CURRENT (mA)
_______________________________________________________________________________________
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
RESET OUTPUT LOW VOLTAGE
vs. SINK CURRENT
RESET OUTPUT HIGH VOLTAGE
vs. SOURCE CURRENT
MAX16025 toc12
0.7
0.6
0.5
0.4
0.3
0.2
0.1
MAX16025 toc11
0.8
RESET OUTPUT HIGH VOLTAGE (V)
3.0
CRESET = VCC
CDLY_ = OPEN
EN_
2.5
2.0
OUT_
1.5
1.0
RESET
0.5
PUSH-PULL VERSIONS
0
0
1
2
3
4
5
7
6
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
SINK CURRENT (mA)
4μs/div
SOURCE CURRENT (mA)
RESET TIMEOUT DELAY
ENABLE TURN-ON
MR FALLING vs. RESET
MAX16025 toc14
MAX16025 toc13
MAX16025 toc15
CRESET = VCC
CDLY_ = OPEN
CRESET = VCC
CDLY_ = OPEN
CRESET = VCC
CDLY_ = OPEN
IN_
EN_
MR
OUT_
OUT_
RESET
RESET
RESET
100ms/div
40ms/div
4μs/div
MAXIMUM TRANSIENT DURATION
vs. THRESHOLD OVERDRIVE
MR RISING vs. RESET
MAX16025 toc16
100
CRESET = VCC
CDLY_ = OPEN
MR
RESET
OUTPUT ASSERTED ABOVE THIS LINE
90
80
MAX16025 toc17
0
MAXIMUM TRANSIENT DURATION (μs)
RESET OUTPUT LOW VOLTAGE (V)
0.9
ENABLE TURN-OFF
3.5
MAX16025 toc10
1.0
70
60
50
40
30
20
10
0
40ms/div
1
10
100
1000
THRESHOLD OVERDRIVE (mV)
_______________________________________________________________________________________
5
MAX16025–MAX16030
Typical Operating Characteristics (continued)
(VCC = 3.3V, TA = +25°C, unless otherwise noted.)
MAX16025–MAX16030
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
Pin Description
PIN
MAX16025/
MAX16026
6
MAX16027/ MAX16029/
MAX16028 MAX16030
NAME
FUNCTION
1
1
1
VCC
Supply Voltage Input. Connect a 2.2V to 28V supply voltage to power the
device. All outputs are low when VCC is below the UVLO. For noisy systems,
bypass VCC to GND with a 0.1µF capacitor.
2
2
2
IN1
Monitored Input 1. When the voltage at IN1 exceeds its threshold, OUT1 goes
high after the capacitor-adjustable delay period. When the voltage at IN1 falls
below its threshold, OUT1 goes low after a propagation delay.
3
3
3
IN2
Monitored Input 2. When the voltage at IN2 exceeds its threshold, OUT2 goes
high after the capacitor-adjustable delay period. When the voltage at IN2 falls
below its threshold, OUT2 goes low after a propagation delay.
—
4
4
IN3
Monitored Input 3. When the voltage at IN3 exceeds its threshold, OUT3 goes
high after the capacitor-adjustable delay period. When the voltage at IN3 falls
below its threshold, OUT3 goes low after a propagation delay.
—
—
5
IN4
Monitored Input 4. When the voltage at IN4 exceeds its threshold, OUT4 goes
high after the capacitor-adjustable delay period. When the voltage at IN4 falls
below its threshold, OUT4 goes low after a propagation delay.
4
5
6
TOL
Threshold Tolerance Input. Connect TOL to GND to select thresholds 5%
below nominal. Connect TOL to VCC to select thresholds 10% below nominal.
5
6
7
GND
Ground
6
7
8
EN1
Active-High Logic-Enable Input 1. Driving EN1 low causes OUT1 to go low
regardless of the input voltage. Drive EN1 high to enable the monitoring
comparator.
7
8
9
EN2
Active-High Logic-Enable Input 2. Driving EN2 low causes OUT2 to go low
regardless of the input voltage. Drive EN2 high to enable the monitoring
comparator.
—
9
10
EN3
Active-High Logic-Enable Input 3. Driving EN3 low causes OUT3 to go low
regardless of the input voltage. Drive EN3 high to enable the monitoring
comparator.
—
—
11
EN4
Active-High Logic-Enable Input 4. Driving EN4 low causes OUT4 to go low
regardless of the input voltage. Drive EN4 high to enable the monitoring
comparator.
8
10
12
TH1
Threshold Select Input 1. Connect TH1 to VCC or GND, or leave it open to
select the input-voltage threshold option in conjunction with TH0 (see Table 2).
9
11
13
TH0
Threshold Select Input 0. Connect TH0 to VCC or GND, or leave it open to
select the input-voltage threshold option in conjunction with TH1 (see Table 2).
—
—
14
OUT4
Output 4. When the voltage at IN4 is below its threshold or EN4 goes low,
OUT4 goes low.
—
12
15
OUT3
Output 3. When the voltage at IN3 is below its threshold or EN3 goes low,
OUT3 goes low.
10
13
16
OUT2
Output 2. When the voltage at IN2 is below its threshold or EN2 goes low,
OUT2 goes low.
_______________________________________________________________________________________
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
PIN
MAX16025/
MAX16026
11
MAX16027/ MAX16029/
MAX16028 MAX16030
14
17
NAME
FUNCTION
OUT1
Output 1. When the voltage at IN1 is below its threshold or EN1 goes low,
OUT1 goes low.
RESET
Active-Low Reset Output. RESET asserts low when any of the monitored
voltages (IN_) falls below its respective threshold, any EN_ goes low, or MR is
asserted. RESET remains asserted for the reset timeout period after all of the
monitored voltages exceed their respective threshold, all EN_ are high, all
OUT_ are high, and MR is deasserted.
12
15
18
13
16
19
14
17
20
—
—
21
—
18
22
15
19
23
CDLY2
Capacitor-Adjustable Delay Input 2. Connect an external capacitor from
CDLY2 to GND to set the IN2 to OUT2 (and EN2 to OUT2) delay period.
Leave CDLY2 open for internal propagation delay.
16
20
24
CDLY1
Capacitor-Adjustable Delay Input 1. Connect an external capacitor from
CDLY1 to GND to set the IN1 to OUT1 (and EN1 to OUT1) delay period.
Leave CDLY1 open for internal propagation delay.
—
—
—
EP
Active-Low Manual Reset Input. Pull MR low to assert RESET low. RESET
remains low for the reset timeout period after MR is deasserted (as long as all
OUT_ are high).
Capacitor-Adjustable Reset Delay Input. Connect an external capacitor from
CRESET to GND to set the reset timeout period or connect to VCC for the
CRESET
default 140ms minimum reset timeout period. Leave CRESET open for internal
propagation delay.
Capacitor-Adjustable Delay Input 4. Connect an external capacitor from
CDLY4 CDLY4 to GND to set the IN4 to OUT4 (and EN4 to OUT4) delay period.
Leave CDLY4 open for internal propagation delay.
Capacitor-Adjustable Delay Input 3. Connect an external capacitor from
CDLY3 CDLY3 to GND to set the IN3 to OUT3 (and EN3 to OUT3) delay period.
Leave CDLY3 open for internal propagation delay.
MR
Exposed Pad. EP is internally connected to GND. Connect EP to the
ground plane.
Table 1. Output State*
EN_
Table 2. Input-Voltage Threshold Selector
IN_
OUT_
Low
VIN_ < VTH
Low
High
VIN_ < VTH
Low
Low
VIN_ > VTH
Low
High
TH1/TH0
LOGIC
IN3
IN4
IN1 (ALL
IN2 (ALL
(MAX16027/ (MAX16029/
VERSIONS) VERSIONS)
MAX16028) MAX16030)
(V)
(V)
(V)
(V)
Low/Low
3.3
2.5
1.8
1.5
OUT_ = high
(MAX16026/MAX16028/
MAX16030)
Low/High
3.3
1.8
Adj
Adj
Adj
OUT_ = high impedance
(MAX16025/MAX16027/
MAX16029)
VIN_ > VTH
*When VCC falls below the UVLO, all outputs go low regardless
of the state of EN_ and VIN_. The outputs are guaranteed to be
in the correct state for VCC down to 1.2V.
Low/Open
3.3
1.5
Adj
High/Low
3.3
1.2
1.8
2.5
High/High
2.5
1.8
Adj
Adj
High/Open
3.3
Adj
2.5
Adj
Open/Low
3.3
Adj
Adj
Adj
Open/High
2.5
Adj
Adj
Adj
Open/Open
Adj
Adj
Adj
Adj
_______________________________________________________________________________________
7
MAX16025–MAX16030
Pin Description (continued)
MAX16025–MAX16030
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
TH0
IN1
TH1
EN4 EN3 EN2 EN1
DELAY
THRESHOLD
SELECT
LOGIC
250nA
LOGIC
DRIVER
OUT1
DRIVER
OUT2
DRIVER
OUT3
DRIVER
OUT4
DRIVER
RESET
1V
IN2
MAX16029
MAX16030
DELAY
IN3
DELAY
IN4
DELAY
GND
RESET
DELAY
LOGIC
TOL
REFERENCE
VCC
CDLY1
CDLY2
CDLY3
CDLY4
CRESET
MR
Figure 1. MAX16029/MAX16030 Simplified Functional Diagram
8
_______________________________________________________________________________________
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
MAX16025–MAX16030
VCC
VUVLO
IN_
VTH
VTH
t < tON
EN_
OUT_
tDELAY-
tON
tON
tDELAY+
tOFF
tRST_DELAY
tRP
tRP
tRP
RESET
Figure 2. Timing Diagram (CDLY_ Open)
Detailed Description
The MAX16025–MAX16030 are low-voltage, accurate,
dual-/triple-/quad-voltage microprocessor (µP) supervisors in a small TQFN package. These devices provide
supervisory and sequencing functions for complex multivoltage systems. The MAX16025/MAX16026 monitor
two voltages, the MAX16027/MAX16028 monitor three
voltages, and the MAX16029/MAX16030 monitor four
voltages.
The MAX16025–MAX16030 offer independent outputs
and enable functions for each monitored voltage. This
configuration allows the device to operate as four separate supervisory circuits or be daisy-chained together to
allow controlled sequencing of power supplies during
power-up initialization. When all of the monitored voltages exceed their respective thresholds, an independent reset output deasserts to allow the system
processor to operate.
These devices offer enormous flexibility as there are
nine threshold options that are selected through two
threshold-select logic inputs. Each monitor circuit also
offers an independent enable input to allow both digital
and analog control of each monitor output. A tolerance
select input allows these devices to be used in systems
requiring 5% or 10% power-supply tolerances. In addition, the time delays and reset timeout can be adjusted
using small capacitors. There is also a fixed 140ms
minimum reset timeout feature.
_______________________________________________________________________________________
9
MAX16025–MAX16030
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
Applications Information
Tolerance
The MAX16025–MAX16030 feature a pin-selectable
threshold tolerance. Connect TOL to GND to select the
thresholds 5% below the nominal value. Connect TOL to
VCC to select the threshold tolerance 10% below the
nominal voltage. Do not leave TOL unconnected.
Adjustable Input
These devices offer several monitoring options with
both fixed and/or adjustable reset thresholds (see
Table 2). For the adjustable threshold inputs, the
threshold voltage (VTH) at each adjustable IN_ input is
typically 0.5V (TOL = GND) or 0.472V (TOL = VCC). To
monitor a voltage VINTH, connect a resistive divider network to the circuit as shown in Figure 3 and use the following equation to calculate the threshold voltage:
where eA is the fraction of the maximum acceptable
absolute resistive divider error attributable to the input
leakage current (use 0.01 for ±1%), VINTH is the voltage at which the output (OUT_) should assert, and IL is
the worst-case IN_ leakage current (see the Electrical
Characteristics). Calculate R2 as follows:
R2 =
VTH × R1
VINTH − VTH
Unused Inputs
Connect any unused IN_ and EN_ inputs to VCC.
R1 ⎞
⎛
VINTH = VTH × ⎜1 +
⎟
⎝ R2 ⎠
OUT_ Output
Choosing the proper external resistors is a balance
between accuracy and power use. The input to the voltage monitor is a high-impedance input with a small
100nA leakage current. This leakage current contributes to the overall error of the threshold voltage
where the output is asserted. This induced error is proportional to the value of the resistors used to set the
threshold. With lower value resistors, this error is
reduced, but the amount of power consumed in the
resistors increases.
VINTH
R1
MAX16025–
MAX16030
IN_
The following equation is provided to help estimate the
value of the resistors based on the amount of acceptable error:
e × VINTH
R1 = A
IL
R2
An OUT_ goes low when its respective IN_ input voltage
drops below its specified threshold or when its EN_ goes
low (see Table 1). OUT_ goes high when EN_ is high and
V IN_ is above its threshold after a time delay. The
MAX16025/MAX16027/MAX16029 feature open-drain,
outputs while the MAX16026/MAX16028/MAX16030
have push-pull outputs. Open-drain outputs require an
external pullup resistor to any voltage from 0 to 28V.
RESET Output
RESET asserts low when any of the monitored voltages
(IN_) falls below its respective threshold, any EN_ goes
low, or MR is asserted. RESET remains asserted for the
reset timeout period after all of the monitored voltages
exceed their respective threshold, all EN_ are high, all
OUT_ are high, and MR is deasserted. The MAX16025/
MAX16027/MAX16029 have an open-drain, active-low
reset output, while the MAX16026/MAX16028/
MAX16030 have a push-pull, active-low reset output.
Open-drain RESET requires an external pullup resistor to
any voltage from 0 to 28V.
Adjustable Reset Timeout Period
(CRESET)
VTH
R1 = R2 x
-1)
( VVINTH
TH
All of these parts offer an internally fixed reset timeout
(140ms min) by connecting CRESET to VCC. The reset
timeout can also be adjusted by connecting a capacitor from CRESET to GND. When the voltage at CRESET
reaches 0.5V, RESET goes high. When RESET goes
high, CRESET is immediately held low.
Figure 3. Setting the Adjustable Input
10
______________________________________________________________________________________
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
V
t RP = TH−RESET × CCRESET + 35 × 10 −6
ICH−RESET
where VTH-RESET is 0.5V, ICH-RESET is 0.5µA, tRP is in
seconds, and CCRESET is in Farads. To ensure timing
accuracy and proper operation, minimize leakage at
CCRESET.
Adjustable Delay (CDLY_)
When VIN rises above VTH with EN_ high, the internal
250nA current source begins charging an external
capacitor connected from CDLY_ to GND. When the
voltage at CDLY_ reaches 1V, OUT_ goes high. When
OUT_ goes high, CDLY_ is immediately held low.
Adjust the delay (tDELAY) from when VIN rises above
VTH (with EN_ high) to OUT_ going high according to
the equation:
V
tDELAY = TH− CDLY × CCDLY + 35 × 10 −6
ICH− CDLY
where VTH-CDLY is 1V, ICH-CDLY is 0.25µA, CCDLY is in
Farads, tDELAY is in seconds, and tDELAY+ is the internal propagation delay of the device. To ensure timing
accuracy and proper operation, minimize leakage
at CDLY.
Manual-Reset Input (MR)
Many µP-based products require manual-reset capability, allowing the operator, a test technician, or external
logic circuitry to initiate a reset. A logic-low on MR
asserts RESET low. RESET remains asserted while MR
is low and during the reset timeout period (140ms fixed
or capacitor adjustable) after MR returns high. The MR
input has a 500nA internal pullup, so it can be left
unconnected, if not used. MR can be driven with TTL or
CMOS logic levels, or with open-drain/collector outputs.
Connect a normally open momentary switch from MR to
GND to create a manual-reset function. External
debounce circuitry is not required. If MR is driven from
long cables or if the device is used in a noisy environment, connect a 0.1µF capacitor from MR to GND to
provide additional noise immunity.
Pullup Resistor Values
The exact value of the pullup resistors for the opendrain outputs is not critical, but some consideration
should be made to ensure the proper logic levels
when the device is sinking current. For example, if
VCC = 2.25V and the pullup voltage is 28V, keep the
sink current less than 0.5mA as shown in the Electrical
Characteristics table. As a result, the pullup resistor
should be greater than 56kΩ. For a 12V pullup, the
resistor should be larger than 24kΩ. Note that the ability
to sink current is dependent on the VCC supply voltage.
Power-Supply Bypassing
The device operates with a VCC supply voltage from
2.2V to 28V. When VCC falls below the UVLO threshold,
all the outputs go low and stay low until VCC falls below
1.2V. For noisy systems or fast rising transients on VCC,
connect a 0.1µF ceramic capacitor from VCC to GND
as close to the device as possible to provide better
noise and transient immunity.
Ensuring Valid Output with VCC Down to
0V (MAX16026/MAX16028/MAX16030 Only)
When VCC falls below 1.2V, the ability for the output to
sink current decreases. In order to ensure a valid output as VCC falls to 0V, connect a 100kΩ resistor from
OUT/RESET to GND.
Typical Application Circuits
Figures 4 and 5 show typical applications for the
MAX16025–MAX16030. In high-power applications,
using an n-channel device reduces the loss across the
MOSFETs as it offers a lower drain-to-source on-resistance. However, an n-channel MOSFET requires a sufficient VGS voltage to fully enhance it for a low RDS_ON.
The application in Figure 4 shows the MAX16027 configured in a multiple-output sequencing application.
Figure 5 shows the MAX16029 in a power-supply
sequencing application using n-channel MOSFETs.
______________________________________________________________________________________
11
MAX16025–MAX16030
Calculate the reset timeout period as follows:
MAX16025–MAX16030
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
+12V BUS
+2.5V
+3.3V
IN
DC-DC
IN
OUT
DC-DC
+1.8V
OUT
IN
DC-DC
EN
EN
IN1
EN1
OUT
EN
OUT1
IN2
EN2
OUT2
EN3
IN3
VCC
OUT3
+3.3V
MAX16027
MR
SYSTEM
RESET
RESET
CDLY1
CDLY3
CDLY2
GND
CRESET
TOL
TH0
TH1
Figure 4. Sequencing Multiple-Voltage System
12V
BUS
1.5V
1.8V
TO
LOADS
2.5V
3.3V
VCC
IN1
OUT1
IN2
OUT2
IN3
+3.3V
IN4
OUT3
OUT4
EN1
EN2
MAX16029
EN3
RESET
EN4
CDLY1
CDLY2
CDLY3
CDLY4
CRESET
GND
TOL
TH0
TH1
MR
Figure 5. Multiple-Voltage Sequencing Using n-Channel FETs
12
______________________________________________________________________________________
SYSTEM
RESET
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
RESET
OUT1
OUT2
TH0
RESET
OUT1
OUT2
OUT3
TH0
TOP VIEW
12
11
10
9
15
14
13
12
11
7
EN2
6
EN1
5
GND
3
4
IN2
TOL
THIN QFN
(4mm x 4mm)
9
EN3
8
EN2
7
EN1
6
GND
MAX16027
MAX16028
CDLY1 20
+
1
VCC
2
IN1
VCC
1
CRESET 17
CDLY2 19
CDLY1 16
+
TH1
CDLY3 18
MAX16025
MAX16026
CDLY2 15
10
2
3
4
5
TOL
CRESET 14
MR 16
IN3
TH1
IN2
8
IN1
MR 13
THIN QFN
(4mm x 4mm)
Chip Information
PROCESS: BICMOS
TRANSISTOR COUNT: 3642
______________________________________________________________________________________
13
MAX16025–MAX16030
Pin Configurations (continued)
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
24L QFN THIN.EPS
MAX16025–MAX16030
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
PACKAGE OUTLINE,
12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm
21-0139
14
______________________________________________________________________________________
E
1
2
Dual-/Triple-/Quad-Voltage, CapacitorAdjustable, Sequencing/Supervisory Circuits
PACKAGE OUTLINE,
12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm
21-0139
E
2
2
Revision History
Pages changed at Rev 1: 1, 3, 15
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 15
© 2007 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
MAX16025–MAX16030
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information
go to www.maxim-ic.com/packages.)
Similar pages