Rohm BA00DD0WCP-V5 Standard variable output ldo regulator Datasheet

Standard Variable Output LDO Regulator Series
Standard Variable
Output LDO Regulators
BA00DD0WCP-V5,BA00DD0WHFP, BA00DD0WT,
BA00CC0WT,BA00CC0WT-V5,BA00CC0WCP-V5,BA00CC0WFP
No.10023EBT01
●Description
The BA00DD0/CC0 series are low-saturation regulators available for outputs up to 2A/1A. The output voltage can be
arbitrarily configured using the external resistance. These series of LDO regulators are offered in a broad packaging lineup.
This IC has a built-in over-current protection circuit that prevents the destruction of the IC due to output short circuits and a
thermal shutdown circuit that protects the IC from thermal damage due to overloading.
●Features
1) Maximum output current: 2A (BA00DD0 series), 1A(BA00CC0 series)
2) ±1% high-precision output voltage (BA00DD0)
3) Low saturation with PNP output
4) Built-in over-current protection circuit that prevents the destruction of the IC due to output short circuits
5) Built-in thermal shutdown circuit for protecting the IC from thermal damage due to overloading
6) Built-in over- voltage protection circuit that prevents the destruction of the IC due to power supply surges
7) TO220FP andHRP5 packaging (BA00DD0), and TO220FP and TO252 packaging (BA00CC0)
●Applications
Usable in DSP power supplies for DVDs and CDs, FPDs, televisions, personal computers or any other consumer device
●Line up
1A BA00CC0 Series
Part Number
BA00CC0WT
BA00CC0WT-V5
BA00CC0WCP-V5
Package
TO220FP-5
TO220FP-5(V5)
TO220CP-V5
BA00CC0WFP
TO252-5
2A BA00DD0 Series
Part Number
BA00DD0WT
BA00DD0WCP-V5
BA00DD0WHFP
Package
TO220FP-5
TO220CP-V5
HRP5
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
1/9
2010.02 - Rev.B
BA00DD0WCP-V5,BA00DD0WHFP,BA00DD0WT,
BA00CC0WT,BA00CC0WT-V5,BA00CC0WCP-V5,BA00CC0WFP
●ABSOLUTE MAXIMUM RATINGS(Ta=25℃)
Parameter
Input Power Supply Voltage*1
Symbol
Vcc
Power Dissipation
*1
*2
*3
Limits
-0.3 ~ +35
2300(HRP5)
1300(TO252-5)
2000(TO220FP-5)
-40 ~ +125
-55 ~ +150
+150
-0.3 ~ +Vcc
+50
Pd
Operating Temperature Range
Ambient Storage Temperature
Junction Temperature
Output Control Terminal Voltage
Voltage Applied to the Tip*3
Technical Note
Topr
Tstg
Tjmax
VCTL
Vcc peak
Unit
V
mW
℃
℃
℃
V
V
Must not exceed Pd
HRP5 : In cases in which Ta≥25℃ when a 70mm×70mm×1.6mm glass epoxy board is used, the power is reduced by 18.4 mW/℃.
TO252-5 : In cases in which Ta≥25℃ when a 70mm×70mm×1.6mm glass epoxy board is used, the power is reduced by 10.4 mW/℃.
TO252FP-5 : No heat sink. When Ta≥25℃, the power is reduced by 16 mW/℃.
Applied voltage: 200msec or less (tr≥1msec)
tr≧1msec
50V
35V
0V
MAX200msec
(Voltage Supply more than 35V)
●Recommended Operating Range (Ta=25℃)
Parameter
BA00CC0□□
Input PowerSupply Voltage
BA00DD0□□
BA00CC0□□
Output Current
BA00DD0□□
Output Control Terminal Voltage
Symbol
Vcc
Io
VCTL
Min.
4.0
3.0
-
-
0
Max.
25.0
25.0
1
2
Vcc
Unit
V
A
V
●Electrical Characteristics(ABRIDGED)
BA00CC0□□ Series (unless specified otherwise, Ta=25℃, Vcc=10V, VCTL=5V, Io=500mA, R1=2.2kΩ, R2=6.8kΩ)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Conditions
C-terminal Voltage
Vc
1.200
1.225
1.250
V
Io=50mA
Circuit Current at the Time of Shutdown
Isd
-
0
10
µA
VCTL=0V
Minimum I/O Voltage Difference
ΔVd
-
0.3
0.5
V
Vcc= 0.95×Vo
Output Current Capacity
Io
1.0
-
-
A
Input Stability
Reg.I
-
20
100
mV
Vcc= 6V→25 V
Load Stability
Reg.L
-
50
150
mV
Io=5mA→1A
Output Voltage Temperature Coefficient*
TCVO
-
±0.02
-
%/℃ Io=5mA ,Tj=0~125℃
*Design guarantee (100% shipping inspection not performed)
BA00DD0□□ Series (unless specified otherwise, Ta=25℃, Vcc=8V, VCTL=3V, Io=500mA, R1=15kΩ, R2=44kΩ)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Conditions
C-terminal Voltage
VADJ
1.257
1.270
1.283
V
Io=100mA
Circuit Current at the Time of Shutdown
Isd
-
0
10
µA
VCTL=0V
Minimum I/O Voltage Difference
ΔVd
-
0.45
0.7
V
Vcc= 0.95×Vo, Io=2A
Output Current Capacity
Io
2.0
-
-
A
Input Stability
Reg.I
-
15
35
mV
Vcc= 5.7V→25 V, Io=200mA
Load Stability
Reg.L
-
50
100
mV
Io=0mA→2A
Output Voltage Temperature Coefficient*
TCVO
-
±0.02
-
%/℃ Io=5mA ,Tj=0~125℃
*Design guarantee (100% shipping inspection not performed)
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
2/9
2010.02 - Rev.B
BA00DD0WCP-V5,BA00DD0WHFP,BA00DD0WT,
BA00CC0WT,BA00CC0WT-V5,BA00CC0WCP-V5,BA00CC0WFP
Technical Note
●Reference Data BA00CC0□□(3.3V preset voltage)
(Unless specified otherwise, Vcc=10V, VOUT=3.3V preset, VCTL=3V, Io=0mA, R1=2.2kΩ, and R2=6.8kΩ)
OUTPUT VOLTAGE:VOUT[V]
CIRCUIT CURRENT:ICC[mA]
2.5
2.0
1.5
1.0
4.0
OUTPUT VOLTAGE:VOUT[V]
4.0
3.0
3.0
2.0
1.0
3.0
2.0
1.0
0.5
0.0
0.0
0
2
4
6
8
10
12
14
16
18
0.0
20
0
2
4
SUPPLY VOLTAGE:VCC[V]
8
10
12
14
16
18
20
0
2
4
SUPPLY VOLTAGE:VCC[V]
Fig.1 Circuit current
1.5
1.0
12
14
16
18
20
70
RIPPLE REJECTION:R.R[dB]
2.0
10
80
500
DROPOUT VOLTAGE:ΔVd[V]
2.5
8
Fig.3 Input Stability
(Io=500mA)
600
3.0
6
SUPPLY VOLTAGE:VCC[V]
Fig.2 Input Stability
3.5
OUTPUT VOLTAGE:VOUT[V]
6
400
300
200
60
50
40
30
20
100
0.5
10
0
0.0
0
0
0
200 400 600 800 1000 1200 1400 1600 1800 2000
10
100 200 300 400 500 600 700 800 900 1000
1000
100
OUTPUT CURRENT:Io[mA]
OUTPUT CURRENT:Io[mA]
Fig.5 Input/Output Voltage Difference
Io-ΔVd Characteristics(Vcc=2.95V)
Fig.4 Load Stability
4.5
200
100000
1k
10k
100k
FREQUENCY:f[Hz]
1000k
Fig.6 Ripple Rejection Characteristics
(Io=100mA)
1000
3.5
3.0
2.5
CONTROL CURRENT:ICTL[μA]
CIRCUIT CURRENT:Icc[mA]
OUTPUT VOLTAGE:VOUT[V]
900
4.0
150
100
50
800
700
600
500
400
300
200
100
0
2.0
-40
-20
0
20
40
60
80
100
120
0
0
AMBIENT TEMPERATURE:Ta[℃]
Fig.8 Circuit Current by load Level
(IOUT=0mA→1A)
7
4
4
4
3
2
1
OUTPUT VOLTAGE:VOUT[V]
4
OUTPUT VOLTAGE:VOUT[V]
4
5
3
3
2
2
1
1
0
2
4
6
8
10
12
14
16
18
20
22
24
CONTROL VOLTAGE:VCTL[V]
Fig.10 CTL Voltage vs. Output Voltage
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
6
8
10
12
14
16
18
20
3
3
2
2
1
1
0
0
4
Fig.9 CTL Voltage vs. CTL Current
8
6
2
CONTROL VOLTAGE:VCTL[V]
OUTPUT CURRENT:Io[mA]
Fig.7 Output Voltage
Temperature Characteristics
OUTPUT VOLTAGE:VOUT[V]
0
100 200 300 400 500 600 700 800 900 1000
0
0
5
10
15
20
25
30
SUPPLY VOLTAGE:Vcc[V]
Fig.11 Overvoltage Operating
Characteristics (Io=200mA)
3/9
35
40
130
140
150
160
170
180
AMBIENT TEMPERATURE:Ta[℃]
Fig.12 Thermal Shutdown
Circuit Characteristics
2010.02 - Rev.B
190
BA00DD0WCP-V5,BA00DD0WHFP,BA00DD0WT,
BA00CC0WT,BA00CC0WT-V5,BA00CC0WCP-V5,BA00CC0WFP
Technical Note
●Reference Data
BA00DD0□□(5.0V preset voltage)
(Unless specified otherwise, Vcc=8V, VOUT=5V preset, VCTL=3V, Io=0mA, R1=15kΩ, and R2=44kΩ)
5.5
OUTPUT VOLTAGE:VOUT[V]
CIRCUIT CURRENT:ICC[mA]
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
8
8
7
7
OUTPUT VOLTAGE:VOUT[V]
6.0
6
5
4
3
2
6
5
4
3
2
1.0
1
0.5
0.0
1
0
0
2
4
6
8
10
12
14
16
18
20
22
24
0
0
2
4
6
8
10
12
14
16
18
20
SUPPLY VOLTAGE:VCC[V]
SUPPLY VOLTAGE:VCC[V]
Fig.13 Circuit Current
Fig.14 Input Stability
8
22
24
0
4
4
3
3
2
RIPPLE REJECTION:R.R[dB]
DROPOUT VOLTAGE:VDRP[V]
OUTPUT VOLTAGE:VOUT[V]
5
600
500
400
300
200
2
100
14
16
18
20
22
24
50
45
40
35
30
25
20
15
5
1
0
1.0
2.0
3.0
4.0
0
0
4.8
0.5
1.0
1.5
OUT PUT CURRENT:IOUT [A]
OUT PUT CURRENT:IOUT [A]
2.0
5.2
200
CONTROL CURRENT:ICTL[μA]
CIRCUIT CURRENT:[mA]
5.1
5.0
4.9
140
120
100
80
60
40
4.8
40
60
80
600
500
400
300
200
0
0
20
1000k
100
20
0
100k
100000
700
160
-20
10k
FREQUENCY:f[Hz]
800
180
-40
1k
1000
100
10
Fig.18 Ripple Rejection Characteristics
Fig.17 Input/Output Voltage Difference
(Iout=100mA)
Iout-ΔVd Characteristics(Vcc=4.75V)
Fig.16 Load Stability
OUTPUT VOLTAGE:VOUT[V]
12
10
1
0.5
100
1.0
1.5
2.0
0
2
4
6
Fig.19 Output Voltage
Temperature Characteristics
Fig.20 Circuit Current by load Level
(IOUT=0mA→2A)
7
47
6
5
4
3
2
1
10
12
14
16
18
20
22
24
Fig.21 CTL Voltage vs. CTL Current
8
OUTPUT VOLTAGE:VOUT[V]
48
OUTPUT VOLTAGE:VOUT[V]
8
8
CONTROL VOLTAGE:VCTL[V]
OUTPUT CURRENT:IOUT[A]
AMBIENT TEMPERATURE:Ta[℃]
OUTPUT VOLTAGE:VOUT[V]
10
55
7
5
8
60
700
6
6
Fig.15 Input Stability
(Io=2A)
800
6
4
SUPPLY VOLTAGE:VCC[V]
8
7
2
36
35
24
23
12
6
4
2
1
0
0
2
4
6
8
10
12
14
16
18
20
22
24
CONTROL VOLTAGE:VCTL[V]
Fig.10 CTL Voltage vs. Output Voltage
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
0
0
0
5
10
15
20
25
30
35
40
SUPPLY VOLTAGE:Vcc[V]
Fig.11 Overvoltage Operating
Characteristics(Io=200mA)
4/9
130
140
150
160
170
180
AMBIENT TEMPERATURE:Ta[℃]
Fig.12 Thermal Shutdown
Circuit Characteristics
2010.02 - Rev.B
190
BA00DD0WCP-V5,BA00DD0WHFP,BA00DD0WT,
BA00CC0WT,BA00CC0WT-V5,BA00CC0WCP-V5,BA00CC0WFP
●Block Diagrams
[BA00CC0WFP]
[BA00DD0WHFP]
Vref
Vcc
[BA00CC0WT] [BA00CC0CP-V5] [BA00CC0WT-V5]
[BA00DD0WT] [BA00DD0WCP-V5]
N.C.(TO252-5)
GND(HRP5)
3
Technical Note
Vref
Driver
4
2
VOUT
Vcc
+
0.33μF
Driver
4
2
VOUT
+
0.33μF
22μF
OVP
1
TSD
Fin
OCP
GND
CTL
22μF
OVP
C(ADJ)
5
R1
1
PINNo. Symbol
Function
Output voltage ON/OFF control
1
2
VCC
Power supply voltage input
2
VCC
Power supply voltage input
3
N.C./GND
Unconnected terminal/GND*
3
GND
GND
4
OUT
4
OUT
Voltage output
5
C
5
ADJ
Output voltage regulation terminal
FIN
GND
1 2 3 4 5
HRP5
R2
Fig.26
TOP VIEW
Function
5
CTL
1 2 3 4 5
TO252-5
C(ADJ)
GND
R1
TOP VIEW
Symbol
OCP
R2
TOP VIEW
PINNo.
3
CTL
Fig.25
FIN
TSD
1
Voltage output
Output voltage regulation terminal
GND
1 2 3 45
1 2 3 45
TO220FP-5 TO220FP-5(V5)
CTL
Output voltage ON/OFF control
*TO252-5 is N.C., and HRP5 is GND
12 3 4 5
TO220CP-V5
●Input / Output Equivalent Circuit Diagrams
< BA00CC0WT/BA00CC0WFP >
Vcc
25kΩ
CTL
C
10 kΩ
25kΩ
VOUT
5.5 kΩ
Fig.27
< BA00DD0WT/BA00DD0WFP >
Vcc
Vcc
Vcc
10kΩ
39kΩ
2kΩ
VOUT
CTL
ADJ
31kΩ
500Ω
Fig.28
●Output Voltage Configuration Method
Please connect resistors R1 and R2 (which determines the output voltage) as shown in Fig.29.
Please be aware that the offset due to the current that flows from the ADJ terminal becomes large when resistors with large
values are used. The use of resistors with R1=2kΩ to 15 kΩ is recommended.
VOUT
Vo = Vc (VADJ) ×
BA□□CC0□□
BA□□DD0□□
1 + R2
R1
R2
Vc
Vc : 1.225 (Typ.)
(VADJ)
C(ADJ)
VADJ : 1.270 (Typ.)
R1
Fig.29
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
5/9
2010.02 - Rev.B
BA00DD0WCP-V5,BA00DD0WHFP,BA00DD0WT,
BA00CC0WT,BA00CC0WT-V5,BA00CC0WCP-V5,BA00CC0WFP
●Thermal Design
HRP5
9
8
6
②5.5W
5
4
3
2
(1)
(2)
TO252-5
2.0
When using a maximum heat sick : θj-c=6.25(℃/W)
When using an IC alone : θj-c=62.5(℃/W)
20
③7.3W
7
Power Dissipation:Pd(W)
Power Dissipation:Pd(W)
To225FP-5
25
Board size : 70×70×1.6 ㎜ 3 (board contains a thermal)
Board front copper foil area : 10.5×10.5 ㎜ 2
①2-layer board (back surface copper foil area :15×15 ㎜ 2)
②2-layer board (back surface copper foil area :70×70 ㎜ 2)
③4-layer board (back surface copper foil area :70×70 ㎜ 2)
15
10
5
①2.3W
Mounted on a Rohm standard board
Board size : 70×70×1.6 ㎜
Copper foil area :7×7 ㎜
TO252-5θja=96.2(℃/W)
1.6
(1)20.0
Power Dissipation:Pd(W)
10
Technical Note
1.30
1.2
0.8
0.4
(2)2.0
1
0
0
0
25
50
75
100
Ambient temperature:Ta(℃)
125
150
Fig.30
0.0
0
25
50
75
100
Ambient temperature:Ta(℃)
125
150
Fig.31
0
25
50
75
100
Ambient temperature:Ta(℃)
125
Fig.32
When using at temperatures over Ta=25℃, please refer to the heat reducing characteristics shown in Fig.30 through 32.
The IC characteristics are closely related to the temperature at which the IC is used, so it is necessary to operate the IC at
temperatures less than the maximum junction temperature TjMAX.
Fig.31 shows the acceptable loss and heat reducing characteristics of the TO220FP package The portion shown by the
diagonal line is the acceptable loss range that can be used with the IC alone. Even when the ambient temperature Ta is a
normal temperature (25℃), the chip (junction) temperature Tj may be quite high so please operate the IC at temperatures
less than the acceptable loss Pd.
Vcc:Input voltage
Vo:Output voltage
The calculation method for power consumption Pc(W) is as follows :
Io:Load current
Icca:Circuit current
Pc = (Vcc-Vo)×Io+Vcc×Icca
Acceptable loss Pd≦Pc
Solving this for load current IO in order to operate within the acceptable loss,
Io≦
Pd – Vcc×Icca
Vcc-Vo
(Please refer to Figs.8 and 20 for Icca.)
It is then possible to find the maximum load current IoMAX with respect to the applied voltage Vcc at the time of thermal design.
Calculation Example
Example 1) When Ta=85℃, Vcc=8.3V, Vo=3.3V, BA33DD0WT
1.04-8.3×Icca
Io≦
5
Io≦200mA (Icca : 2mA)
With the IC alone : θja=62.5℃/W → -16mW/℃
25℃=2000mW → 85℃=1040mW
Please refer to the above information and keep thermal designs within the scope of acceptable loss for all operating
temperature ranges. The power consumption Pc of the IC when there is a short circuit (short between Vo and GND) is :
Pc=Vcc×(Icca+Ishort)
Ishort : Short circuit current
●Terminal Vicinity Settings and Cautions
・Vcc Terminal
Please attach a capacitor (greater than 0.33μF) between the Vcc and GND.
The capacitance values differ depending on the application, so please chose a capacitor with sufficient margin and verify
the operation on an actual board.
・CTL Terminal
The CTL terminal is turned ON at 2.0V and higher and OFF at 0.8V and lower within the operating power supply voltage range.
The power supply and the CTL terminal may be started up and shut down in any order without problems.
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
6/9
2010.02 - Rev.B
150
BA00DD0WCP-V5,BA00DD0WHFP,BA00DD0WT,
BA00CC0WT,BA00CC0WT-V5,BA00CC0WCP-V5,BA00CC0WFP
Technical Note
●Vo Terminal
Please attach an anti-oscillation capacitor between VOUT and GND. The capacitance of the capacitor may significantly
change due to factors such as temperature changes, which may cause oscillations. Please use a tantalum capacitor or
aluminum electrolytic capacitor with favorable characteristics and small external series resistance (ESR) even at low
temperatures. The output oscillates regardless of whether the ESR is large or small. Please use the IC within the stable
operating region while referring to the ESR characteristics reference data shown in Figs.33 through 35. In cases where there
are sudden load fluctuations, the a large capacitor is recommended.
100
EFFECTIVE SERIES RESISTANCE:ESR [Ω]
OUT
IC
22μF
C(ADJ)
Fig.33:Output equivalent circuit
Unstable operating region
10
Stable operating region
1
Unstable operating region
0.1
0
1000
200
600
800
400
OUTPUT CURRENT:lo(mA)
EFFECTIVE SERIES RESISTANCE:ESR [Ω]
Unstable operating region
100
10
Stable operating region
1
Unstable operating region
0.1
1
10
OUTPUT
Fig.34:Io vs. ESR characteristics
(BA□□CC0)
100
CURRENT:lo(mA)
1000
Fig.35: Io vs. ESR characteristics
(BA□□DD0)
●Other
1) Protection Circuits
Overcurrent Protection Circuit
A built-in overcurrent protection circuit corresponding to the current capacity prevents the destruction of the IC when there
are load shorts. This protection circuit is a “7”-shaped current control circuit that is designed such that the current is
restricted and does not latch even when a large current momentarily flows through the system with a high-capacitance
capacitor. However, while this protection circuit is effective for the prevention of destruction due to unexpected accidents, it
is not suitable for continuous operation or transient use. Please be aware when creating thermal designs that the overcurrent
protection circuit has negative current capacity characteristics with regard to temperature (Refer to Figs.4 and 16).
Thermal Shutdown Circuit (Thermal Protection)
This system has a built-in temperature protection circuit for the purpose of protecting the IC from thermal damage. As
shown above, this must be used within the range of acceptable loss, but if the acceptable loss happens to be continuously
exceeded, the chip temperature Tj increases, causing the temperature protection circuit to operate.
When the thermal shutdown circuit operates, the operation of the circuit is suspended. The circuit resumes operation
immediately after the chip temperature Tj decreases, so the output repeats the ON and OFF states (Please refer to
Figs.12 and 24 for the temperatures at which the temperature protection circuit operates).
There are cases in which the IC is destroyed due to thermal runaway when it is left in the overloaded state. Be sure to
avoid leaving the IC in the overloaded state.
Reverse Current
In order to prevent the destruction of the IC when a reverse current flows through the IC, it is recommended that a diode
be placed between the Vcc and Vo and a pathway be created so that the current can escape (Refer to Fig.36).
2) This IC is bipolar IC that has a P-board (substrate) and P+ isolation layer
between each devise, as shown in Fig.37. A P-N junction is formed between
this P-layer and the N-layer of each device, and the P-N junction operates as a
parasitic diode when the electric potential relationship is GND> Terminal A,
GND> Terminal B, while it operates as a parasitic transistor when the electric
potential relationship is Terminal B GND> Terminal A. Parasitic devices are
intrinsic to the IC. The operation of parasitic devices induces mutual
interference between circuits, causing malfunctions and eventually the
destruction of the IC itself. It is necessary to be careful not to use the IC in ways
that would cause parasitic elements to operate. For example, applying a
voltage that is lower than the GND (P-board) to the input terminal.
Transistor (NPN)
B
(Pin B) O
E
Reverse current
CTL
(Pin A)
Fig. 36:Bypass diode
(Pin B)
GND
N
P+
P
N
P+
N
P
P
P+
P
N
GND
GND
Parasitic element
Fig. 37: Example of the basic structure of a bipolar IC
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
Parasitic element
or transistor
N
GND
Parasitic element
or transistor
C
E
N
N
GND
Resistor
B
P+
OUT
Vcc
7/9
(Pin A)
Parasitic element
GND
2010.02 - Rev.B
BA00DD0WCP-V5,BA00DD0WHFP,BA00DD0WT,
BA00CC0WT,BA00CC0WT-V5,BA00CC0WCP-V5,BA00CC0WFP
Technical Note
●Ordering part number
B
A
0
Part No.
0
C
Output voltage
00:Variable
C
Series
CC0 : 1A
DD0 : 2A
0
W
H
Shutdown
switch
W : Includes
switch
F
P
Package
HFP :HRP5
FP :TO252
CP :TO220CP
T
:TO220FP
-
T
R
Packaging and forming specification
TR: Embossed tape and reel
(HRP5)
E2: Embossed tape and reel
(TO252-5,TO220CP)
None : Container Tube
V5 :Foaming(V5 only)
HRP5
<Tape and Reel information>
1.017±0.2
9.395±0.125
(MAX 9.745 include BURR)
8.82 ± 0.1
(5.59)
0.08±0.05
1.2575
1
2
3
4
0.835±0.2
1.523±0.15
10.54±0.13
8.0±0.13
(7.49)
1.905±0.1
Tape
Embossed carrier tape
Quantity
2000pcs
TR
Direction
of feed
direction is the 1pin of product is at the upper right when you hold
( The
)
reel on the left hand and you pull out the tape on the right hand
1pin
5
+5.5°
4.5°−4.5°
+0.1
0.27 −0.05
S
0.73±0.1
0.08 S
1.72
Direction of feed
Reel
(Unit : mm)
∗ Order quantity needs to be multiple of the minimum quantity.
TO252-5
<Tape and Reel information>
2.3±0.2
6.5±0.2
C0.5
1.5±0.2
+0.2
5.1 -0.1
Tape
Embossed carrier tape
Quantity
2000pcs
0.5±0.1
E2
Direction
of feed
The direction is the 1pin of product is at the lower left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
1.5
4 5
0.8
1 2 3
2.5
9.5±0.5
5.5±0.2
FIN
0.5±0.1
0.5
1.27
1.0±0.2
1pin
Reel
(Unit : mm)
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
TO220CP-V5
1.444
<Tape and Reel information>
4.5±0.1
0.82±0.1
0.92
1.778
Tape
Embossed carrier tape
Quantity
500pcs
E2
Direction
of feed
The direction is the 1pin of product is at the lower left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
16.92
13.60
+0.2
2.8 -0.1
(1.0)
8.0 ± 0.2
12.0 ± 0.2
4.92 ± 0.2
1.0 ± 0.2
+0.4
15.2 -0.2
+0.3 φ3.2±0.1
10.0 -0.1
0.42±0.1
1.58
(2.85)
4.12
(Unit : mm)
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
Reel
8/9
1pin
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
2010.02 - Rev.B
BA00DD0WCP-V5,BA00DD0WHFP,BA00DD0WT,
BA00CC0WT,BA00CC0WT-V5,BA00CC0WCP-V5,BA00CC0WFP
Technical Note
<Tape and Reel information>
+0.3
4.5 −0.1
+0.2
2.8 −0.1
φ3.2±0.1
Container
Tube
Quantity
500pcs
Direction of feed
Direction of products is fixed in a container tube
8.0±0.2
0.7
12.0±0.2
+0.3
10.0−0.1
+0.3
7.0 −0.1
13.5Min.
+0.4
17.0 −0.2
1.8±0.2
TO220FP-5
1.2
0.8
1.778
0.5±0.1
2.85
1 2 3 4 5
∗ Order quantity needs to be multiple of the minimum quantity.
(Unit : mm)
(2.0)
φ3.2±0.1
17.5
0.3
7.0 +
− 0.1
<Tape and Reel information>
+0.2
2.8 −0.1
Container
Tube
Quantity
500pcs
Direction of feed
Direction of products is fixed in a container tube
25.8
+0.3
4.5 −0.1
23.4
12.0±0.2
+ 0.3
10.0 − 0.1
8.0±0.2
0.7
+0.4
17.0 −0.2
31.5Max.
1.8±0.2
TO220FP-5(V5)
1.2
0.8
0.5±0.1
1.778
(2.85)
4.25
8.15
1 2 3 4 5
∗ Order quantity needs to be multiple of the minimum quantity.
(Unit : mm)
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
9/9
2010.02 - Rev.B
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
R1010A
Similar pages