LINER LT1671CMS8 60ns, low power, single supply, ground-sensing comparator Datasheet

LT1671
60ns, Low Power,
Single Supply, Ground-Sensing
Comparator
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
DESCRIPTIO
Low Power: 450µA
Fast: 60ns at 20mV Overdrive
85ns at 5mV Overdrive
Low Offset Voltage: 0.8mV
Operates Off Single 5V or Dual ±5V Supplies
Input Common Mode Extends to Negative Supply
No Minimum Input Slew Rate Requirement
Complementary TTL Outputs
Inputs Can Exceed Supplies without Phase Reversal
Pin Compatible with LT1394, LT1016 and LT1116
Output Latch Capability
Available in 8-Lead MSOP and SO Packages
U
APPLICATIO S
■
■
■
■
■
■
■
■
High Speed A/D Converters
Zero-Crossing Detectors
Current Sense for Switching Regulators
Extended Range V/F Coverters
Fast Pulse Height/Width Discriminators
High Speed Triggers
Line Receivers
High Speed Sampling Circuits
The LT ®1671 is a low power 60ns comparator with complementary outputs and latch. The input common mode
range extends from 1.5V below the positive supply down
to the negative supply rail. Like the LT1394, LT1016 and
LT1116, this comparator has complementary outputs
designed to interface directly to TTL or CMOS logic. The
LT1671 may operate from either a single 5V supply or dual
±5V supplies. Low offset voltage specifications and high
gain allow the LT1671 to be used in precision applications.
The LT1671 is designed for improved speed and stability
for a wide range of operating conditions. The output stage
provides active drive in both directions for maximum
speed into TTL, CMOS or passive loads with minimal
cross-conduction current. Unlike other fast comparators,
the LT1671 remains stable even for slow transitions
through the active region, which eliminates the need to
specify a minimum input slew rate.
The LT1671 has an internal, TTL/CMOS compatible latch
for retaining data at the outputs. The latch holds data as
long as the LATCH pin is held high. Device parameters
such as gain, offset and negative power supply current are
not significantly affected by variations in negative supply
voltage.
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
TYPICAL APPLICATIO
Propagation Delay vs Overdrive
140
1MHz Crystal Oscillator
VS = ±5V
VSTEP = 100mV
TA = 25°C
RL = 1M
120
5V
1MHz CRYSTAL
(AT-CUT)
100
TIME (ns)
2k
+
2k
LT1671
OUTPUT
80
FALLING EDGE (tPDHL)
60
–
40
2k
0.068µF
20
1671 TA01
1671 TA01
RISING EDGE (tPDLH)
0
10
20
30
OVERDRIVE (mV)
40
50
1671 TA02
1
LT1671
U
W W
W
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Total Supply Voltage (V+ to V–) ............................... 12V
Positive Supply Voltage ............................................. 7V
Negative Supply Voltage .......................................... – 7V
Differential Input Voltage ....................................... ±12V
Input and Latch Current (Note 2) ........................ ±10mA
Output Current (Continuous)(Note 2) ................. ±20mA
Operating Temperature Range ................ – 40°C to 85°C
Specified Temperature Range (Note 3) ... – 40°C to 85°C
Junction Temperature ........................................... 150°C
Storage Temperature Range ................. – 65°C to 150°C
Lead Temperature (Soldering, 10 sec.)................. 300°C
W
U
U
PACKAGE/ORDER INFORMATION
ORDER PART
NUMBER
TOP VIEW
V+ 1
+IN 2
–IN 3
V– 4
8
7
6
5
Q OUT
Q OUT
GND
LATCH
ENABLE
MS8 PACKAGE
8-LEAD PLASTIC MSOP
LT1671CMS8
V+ 1
+IN 2
–IN 3
MS8 PART MARKING
TJMAX = 150°C, θJA = 250°C/ W
LTCT
ORDER PART
NUMBER
TOP VIEW
V– 4
8 Q OUT
+
–
LT1671CS8
LT1671IS8
7 Q OUT
6 GND
5
LATCH
ENABLE
S8 PART MARKING
S8 PACKAGE
8-LEAD PLASTIC SO
1671
1671I
TJMAX = 150°C, θJA = 190°C/ W
Consult factory for Military grade parts.
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25°C.
V + = 5V, V – = – 5V, VOUT(Q) = 1.4V, VLATCH = VCM = 0V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
VOS
Input Offset Voltage
RS ≤ 100Ω (Note 4)
MIN
TYP
MAX
0.8
2.5
4.0
●
∆VOS
∆T
IOS
Input Offset Voltage Drift
Input Offset Current
10
100
150
nA
nA
120
280
350
nA
nA
3.5
3.5
V
V
●
IB
Input Bias Current
(Note 5)
●
VCMR
Input Voltage Range (Note 6)
Single 5V Supply
CMRR
Common Mode Rejection Ratio
–5
0
– 5V ≤ VCM ≤ 3.5V, TA > 0°C
– 5V ≤ VCM ≤ 3.3V, TA ≤ 0°C
55
55
100
dB
dB
Single 5V Supply
0V ≤ VCM ≤ 3.5V, TA > 0°C
0V ≤ VCM ≤ 3.3V, TA ≤ 0°C
55
55
100
dB
dB
50
60
85
90
dB
dB
2500
5000
V/V
PSRR
Power Supply Rejection Ratio
4.6V ≤ V + ≤ 5.4V
– 7V ≤ V – ≤ – 2V
AV
Small Signal Voltage Gain
1V ≤ VOUT ≤ 2V
2
●
●
mV
mV
µV/°C
4
●
UNITS
●
●
LT1671
ELECTRICAL CHARACTERISTICS
The ● denotes specifications which apply over the full operating temperature range, otherwise specifications are TA = 25°C.
V + = 5V, V – = – 5V, VOUT(Q) = 1.4V, VLATCH = VCM = 0V unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
VOH
Output Voltage Swing High
V+
≥ 4.6V, IOUT = 400µA
V + ≥ 4.6V, IOUT = 4mA
●
●
VOL
Output Voltage Swing Low
IOUT = – 400µA
IOUT = – 4mA
●
I+
Positive Supply Current
MIN
TYP
2.7
2.4
3.1
3.0
Negative Supply Current
LATCH Pin High Input Voltage
●
VIL
LATCH Pin Low Input Voltage
●
IIL
LATCH Pin Current
VLATCH = 0V
t PD1
Propagation Delay
∆VIN = 100mV, VOD = 20mV
●
V
V
450
800
1000
µA
µA
75
200
250
µA
µA
2
V
0.8
– 1000
– 250
Propagation Delay (Note 7)
∆VIN = 100mV, VOD = 5mV
nA
80
110
ns
ns
85
100
130
ns
ns
15
30
ns
●
∆VIN = 100mV, VOD = 5mV
V
60
●
t PD2
V
V
0.5
●
VIH
UNITS
0.3
0.4
●
I–
MAX
∆t PD
Differential Propagation Delay (Note 7)
t LPD
Latch Propagation Delay (Note 8)
60
t SU
Latch Setup Time (Note 8)
– 15
ns
tH
Latch Hold Time (Note 8)
35
ns
t PW(D)
Minimum Disable Pulse Width
30
ns
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: This parameter is guaranteed to meet specified performance
through design and characterization. It has not been tested.
Note 3: The LT1671CS8 and LT1671CMS8 are guaranteed to meet
specified performance from 0°C to 70°C and are designed, characterized
and expected to meet these extended temperature limits, but are not tested
at – 40°C and 85°C. The LT1671IS8 is guaranteed to meet the extended
temperature limits.
Note 4: Input offset voltage (VOS) is defined as the average of the two
voltages measured by forcing first one output, then the other to 1.4V.
Note 5: Input bias current (IB) is defined as the average of the two input
currents.
Note 6: Input voltage range is guaranteed in part by CMRR testing and in
part by design and characterization.
ns
Note 7: tPD and ∆tPD cannot be measured in automatic handling
equipment with low values of overdrive. The LT1671 is 100% tested with a
100mV step and 20mV overdrive. Correlation tests have shown that tPD
and ∆tPD limits can be guaranteed with this test, if additional DC tests are
performed to guarantee that all internal bias conditions are correct.
Propagation delay (t PD) is measured with the overdrive added to the actual
VOS. Differential propagation delay is defined as:
∆t PD = t PDLH – t PDHL
Note 8: Latch propagation delay (t LPD) is the delay time for the output to
respond when the LATCH pin is deasserted. Latch setup time (t SU) is the
interval in which the input signal must remain stable prior to asserting the
latch signal. Latch hold time (tH) is the interval after the latch is asserted in
which the input signal must remain stable.
3
LT1671
U W
TYPICAL PERFORMANCE CHARACTERISTICS
Propagation Delay vs
Load Capacitance
Gain Characteristics
VS = ±5V
RL = 1M
TA = 25°C
3.5
TA = – 55°C
TIME (ns)
3.0
2.5
2.0
80
80
RISING EDGE (tPDLH)
70
VS = ±5V
VSTEP = 100mV
VOD = 5mV
TA = 25°C
RL = 1M
1.5
60
1.0
0.5
0
–3
50
–2
–1
1
2
0
DIFFERENTIAL INPUT VOLTAGE (mV)
0
3
50
10
20
30
40
OUTPUT LOAD CAPACITANCE (pF)
50
4.4
VS = ±5V
RL = 1M
VOD = 20mV
TA = 25°C
180
160
TIME (ns)
80
FALLING EDGE (tPDHL)
Propagation Delay vs
Temperature
100
200
VS = ±5V
VSTEP = 100mV
TA = 25°C
RL = 1M
80
400mV
70
140
200mV
120
40
RISING EDGE (tPDLH)
50
40
10
20
30
OVERDRIVE (mV)
20
60
40
0
STEP SIZE = 100mV
50
40
10
0
5
10
SOURCE RESISTANCE (kΩ)
t PDLH
60
30
80
t PDHL
90
STEP SIZE = 800mV
100
60
5.6
4.6
4.8
5.0
5.2
5.4
POSITIVE SUPPLY VOLTAGE (V)
1671 G03
Propagation Delay vs
Source Resistance
100
TIME (ns)
V – = –5V
VSTEP = 100mV
VOD = 5mV
TA = 25°C
RL = 1M
1671 G02
Propagation Delay vs
Input Overdrive
120
RISING EDGE (tPDLH)
70
60
1671 G01
140
FALLING EDGE (tPDHL)
FALLING EDGE (tPDHL)
90
TIME (ns)
4.0
TIME (ns)
TA = 125°C
4.5
OUTPUT VOLTAGE (V)
90
100
5.0
20
Propagation Delay vs
Positive Supply Voltage
VS = ±5V
VSTEP = 100mV
VOD = 5mV
RL = 1M
0
–50 –25
15
50
0
75
25
TEMPERATURE (°C)
100
125
1671 TA02
1671 G05
Input Offset Voltage vs
Temperature
Input Bias Current vs
Temperature
500
INPUT BIAS CURRENT (nA)
VS = ±5V
RL = 1M
VOLTAGE (mV)
2
1
0
–1
Positive Common Mode Limit vs
Temperature
6
VS = ±5V
RL = 1M
5
400
VOLTAGE (V)
4
3
1671 G06
300
200
VCM = –5V
VS = ±5V
RL = 1M
4
3
2
100
VCM = 0V
1
–2
VCM = 3.5V
–3
–50 –25
50
0
75
25
TEMPERATURE (°C)
100
125
1671 G07
4
0
–50 –25
50
0
75
25
TEMPERATURE (°C)
100
125
1671 G08
0
–50 –25
50
25
0
75
TEMPERATURE (°C)
100
125
1671 G09
LT1671
U W
TYPICAL PERFORMANCE CHARACTERISTICS
Negative Common Mode Limit vs
Temperature
Output Low Voltage (VOL) vs
Output Sink Current
1
0.8
RL = 1M
5.0
VS = ±5V
VIN = 30mV
0.7
0
VS = SINGLE 5V SUPPLY
–3
–4
OUTPUT VOLTAGE (V)
–2
TA = –55°C
0.5
TA = 125°C
0.4
TA = 25°C
0.3
0.2
VS = ±5V
–5
0.1
50
0
75
25
TEMPERATURE (°C)
100
4
6
10
8
12
2.5
2.0
14
4
8
6
10
12
OUTPUT SOURCE CURRENT (mA)
2
0
1671 G11
Positive Supply Current vs
V + Supply Voltage
14
1671 G12
Positive Supply Current vs
Switching Frequency
Negative Supply Current vs
V – Supply Voltage
3.5
V – = 0V
VIN = –60mV
IOUT = 0
0.5
TA = 25°C
TA = –55°C
3.0
OUTPUT SINK CURRENT (mA)
1671 G10
0.6
TA = 125°C
3.5
1.0
2
0
125
4.0
1.5
0
–6
–50 –25
VS = ±5V
VIN = –30mV
4.5
0.6
–1
VOLTAGE (V)
INPUT VOLTAGE (V)
Output High Voltage (VOH) vs
Output Source Current
100
VS = ±5V
VSTEP = ±50mV
IOUT = 0
3.0
V+ = 5V
VIN = –60mV
IOUT = 0
90
TA = 25°C
0.3
TA = 125°C
TA = –55°C
0.2
CURRENT (µA)
CURRENT (mA)
0.4
2.0
TA = 125°C
1.5
TA = 125°C
70
TA = 25°C
TA = 25°C
0.1
0
80
1.0
0.5
60
TA = –55°C
TA = –55°C
0
0
1
2
6
4
3
5
SUPPLY VOLTAGE (V)
7
8
1
SWITCHING FREQUENCY (MHz)
0.1
50
–8
–7 –6 –5 –4 –3 –2 –1
NEGATIVE SUPPLY VOLTAGE (V)
0
1671 G15
Response to 15MHz
±10mV Sine Wave
Latch Pin Current vs Temperature
1.0
10
1671 G14
1671 G13
CURRENT (µA)
CURRENT (mA)
2.5
VS = ±5V
0.8
+IN
20mVP-P
10mV/DIV
0.6
3V
Q OUT
1V/DIV
0.4
0V
0.2
0
–50 –25
50ns/DIV
50
0
75
25
TEMPERATURE (°C)
100
1671 G17
125
1671 G16
5
LT1671
U W
TYPICAL PERFORMANCE CHARACTERISTICS
tPD+ Response Time to
5mV Overdrive
tPD– Response Time to
5mV Overdrive
1.4V
1.4V
5mV
5mV
+IN
+IN
Q OUT
– 95mV
0V
VS = ±5V
VOD = 5mV
Q OUT
– 95mV
VS = ±5V
VOD = 5mV
20ns/DIV
1671 G18
0V
20ns/DIV
1671 G19
U
U
U
PIN FUNCTIONS
V + (Pin 1): Positive Supply Voltage. Normally 5V.
GND (Pin 6): Ground.
+IN (Pin 2): Noninverting Input.
–IN (Pin 3): Inverting Input.
Q OUT (Pin 7): Noninverting Logic Output. This pin is high
when +IN is above – IN and LATCH ENABLE is low.
V – (Pin 4): Negative Supply Voltage. Normally either 0V
or – 5V.
Q OUT (Pin 8): Inverting Logic Output. This pin is low
when +IN is above – IN and LATCH ENABLE is low.
LATCH ENABLE (Pin 5): Latch Control Pin. When high, the
outputs remain in a latched condition, independent of the
current state of the inputs.
WU
W
TI I G DIAGRA S
VOD
VIN
LATCH
ENABLE
∆VIN
tH
tSU
tPD
VIN
VOUT
tPD
1671 TD01
VOUT
1671 TD02
6
LT1671
U
U
W
U
APPLICATIONS INFORMATION
Common Mode Considerations
Input Bias Current
The LT1671 is specified for a common mode range of – 5V
to 3.5V on a ±5V supply or a common mode range of 0V
to 3.5V on a single 5V supply. A more general consideration is that the common mode range is 0V below the
negative supply and 1.5V below the positive supply, independent of the actual supply voltage. The criterion for
common mode limit is that the output still responds
correctly to a small differential input signal.
Input bias current is measured with the output held at
1.4V. As with any PNP differential input stage, the LT1671
bias current flows out of the device. It will go to zero on an
input which is high and double on an input which is low.
When either input signal falls below the negative common
mode limit, the internal PN diode formed with the substrate can turn on, resulting in significant current flow
through the die. An external Schottky clamp diode
between the input and the negative rail can speed up
recovery from negative overdrive by preventing the substrate diode from turning on.
The zero crossing detector in Figure 1 demonstrates the
use of a fast clamp diode. The zero crossing detector
terminates the transmission line at its 50Ω characteristic
impedance. Negative inputs should not fall below –2V to
keep the signal current within the clamp diode’s maximum
forward rating. Positive inputs should not exceed the
devices absolute maximum ratings nor the power rating
on the terminating resistor.
RS
50Ω
5V
CABLE
+
VIN
1N5712
RT
50Ω
Q
LT1671
–
Q
1671 F01
Figure 1. Fast Zero Crossing Detector
Either input may go above the positive common mode
limit without damaging the comparator. The upper voltage
limit is determined by an internal diode from each input to
the positive supply. The input may go above the positive
supply as long as it does not go far enough above it to
conduct more than 10mA. Functionality will continue if the
remaining input stays within the allowed common mode
range. There will, however, be an increase in propagation
delay as the input signal switches back into the common
mode range.
LATCH Pin Dynamics
The LATCH pin is intended to retain input data (output
latched) when the LATCH pin goes high. The pin will float
to a high state when disconnected, so a flow-through
condition requires that the LATCH pin be grounded. The
LATCH pin is designed to be driven with either a TTL or
CMOS output. It has no built-in hysteresis.
To guarantee data retention, the input signal must remain
valid at least 35ns after the latch goes high (hold time), and
must be valid at least – 15ns before the latch goes high
(setup time). The negative setup time simply means that
the data arriving 15ns after (rather than before) the latch
signal is valid. When the latch signal goes low, new data
will appear at the output in approximately 60ns (latch
propagation delay).
Measuring Response Time
To properly measure the response of the LT1671 requires
an input signal source with very fast rise times and
exceptionally clean settling characteristics. The last
requirement comes about because the standard comparator test calls for an input step size that is large compared
to the overdrive amplitude. Typical test conditions are
100mV step size with 5mV overdrive. This requires an
input signal that settles to within 1% (1mV) of final value
in only a few nanoseconds with no ringing or settling tail.
Ordinary high speed pulse generators are not capable of
generating such a signal, and in any case, no ordinary
oscilloscope is capable of displaying the waveform to
check its fidelity. Some means must be used to inherently
generate a fast, clean edge with known final value. The
circuit shown in Figure 2 is the best electronic means of
generating a fast, clean step to test comparators. It uses
a very fast transistor in a common base configuration. The
transistor is switched off with a fast edge from the generator and the collector voltage settles to exactly 0V in just a
few nanoseconds. The most important feature of this
7
LT1671
U
U
W
U
APPLICATIONS INFORMATION
5V
0.01µF*
0V
25Ω
–100mV
25Ω
0.1µF
+
2N3866
10k
V1**
–
FET PROBE
Q
0.01µF
50Ω
0V
–3V
FET PROBE
LT1671
130Ω
PULSE
IN
Q
* TOTAL LEAD LENGTH INCLUDING DEVICE PIN.
SOCKET AND CAPACITOR LEADS SHOULD BE
LESS THAN 0.5 IN. USE GROUND PLANE
** (VOS + OVERDRIVE)/200
50Ω
400Ω
750Ω
–5V
1671 F02
–5V
Figure 2. Response Time Test Circuit
circuit is the lack of feedthrough from the generator to the
comparator input. This prevents overshoot on the comparator input, which would give a false fast reading on
comparator response time.
Bypass capacitors should be as close as possible to the
LT1671. A good high frequency capacitor such as a 0.1µF
ceramic is recommended, in parallel with a larger capacitor such as a 4.7µF tantalum.
To adjust the circuit for exactly 5mV overdrive, V1 is
adjusted so that the LT1671 output under test settles to
1.4V (in the linear region). Then V1 is changed by – 1V to
set overdrive to 5mV.
Poor trace routes and high source impedances are also
common sources of problems. Be sure to keep trace
lengths as short as possible, and avoid running any output
trace adjacent to an input trace to prevent unnecessary
coupling. If output traces are longer than a few inches, be
sure to terminate them with a resistor to eliminate any
reflections that may occur. Resistor values are typically
250Ω to 400Ω. Also, be sure to keep source impedances
as low as possible, preferably 1kΩ or less.
High Speed Design Techniques
A substantial amount of design effort has made the LT1671
relatively easy to use. It is much less prone to oscillation
than some slower comparators, even with slow input
signals. However, as with any high speed comparator,
there are a number of problems which may arise because
of PC board layout and design. The most common problem involves power supply bypassing. Bypassing is necessary to maintain low supply impedance. DC resistance
and inductance in supply wires and PC traces can quickly
build up to unacceptable levels. This allows the supply line
to move with changing internal current levels of the
connected devices. This will almost always result in
improper operation. In addition, adjacent devices connected through an unbypassed supply can interact with
each other through the finite supply impedances. Bypass
capacitors furnish a simple solution to this problem by
providing a local reservoir of energy at the device, keeping
supply impedances low.
8
About Level Shifts
The LT1671’s logic output will interface with many circuits directly. Many applications, however, require some
form of level shifting of the output swing. With LT1671based circuits this is not trivial because it is desirable to
maintain very low delay in the level shifting stage. When
designing level shifters, keep in mind that the TTL output
of the LT1671 is a sink-source pair (Figure 3) with good
ability to drive capacitance (such as feedforward capacitors). Figure 4 shows a noninverting voltage gain stage
with a 15V output. When the LT1671 switches, the baseemitter voltages at the 2N2369 reverse, causing it to
switch very quickly. The 2N3866 emitter-follower gives a
low impedance output and the Schottky diode aids current sink capability.
LT1671
U
U
W
U
APPLICATIONS INFORMATION
LT1671 is the key to low delay, providing Q2’s base with
nearly ideal drive. This capacitor loads the LT1671’s
output transition, but Q2’s switching is clean with 3ns
delay on the rise and fall of the pulse. Figure 6 is similar to
Figure 4 except that a sink transistor has replaced the
Schottky diode. The two emitter-followers drive a power
MOSFET that switches 1A at 15V. Most of the 7ns to 9ns
delay in this stage occurs in the MOSFET and the 2N2369.
+V
OUTPUT = 0 → +V (TYPICALLY 3V TO 4V)
1671 F03
Figure 3. Simplified LT1671 Output Stage
When designing level shifters, remember to use transistors with fast switching times and high fT. To get the kind
of results shown, switching times in the nanosecond
range and an fT approaching 1GHz are required.
15V
1k
2N2369
+
2N3866
HP5082-2810
LT1671
15V
OUT
–
1k
12pF
1k
1k
RISE TIME = 4ns
FALL TIME = 5ns
RL
2N2369
+
1671 F04
2N3866
POWER
FET
LT1671
–
Figure 4. Level Shift Has Noninverting Voltage Gain
2N5160
1k
1k
12pF
1671 F06
Figure 5 is a very versatile stage. It features a bipolar swing
that is set by the output transistor’s supplies. This 3ns
delay stage is ideal for driving FET switch gates. Q1, a
gated current source, switches the Baker-clamped output
transistor, Q2. The heavy feedforward capacitor from the
RISE TIME = 7ns
FALL TIME = 9ns
Figure 6. Noninverting Voltage Gain Level Shift
5V
+
INPUT
LT1671
–
1N4148
4.7k
430Ω
Q1
2N2907
1000pF
0.1µF
820Ω
5V (TYP)
HP5082-2810
330Ω
Q2
2N2369
RISE TIME = 3ns
FALL TIME = 3ns
5V
OUTPUT
–10V
OUTPUT TRANSISTOR SUPPLIES
(SHOWN IN HEAVY LINES)
CAN BE REFERENCED ANYWHERE
BETWEEN 15V AND –15V
1671 F05
820Ω
–10V (TYP)
Figure 5. Level Shift with Inverting Voltage Gain—Bipolar Swing
9
LT1671
U
U
W
U
APPLICATIONS INFORMATION
Crystal Oscillators
Switchable Output Crystal Oscillator
Figure 7 shows a crystal oscillator circuit. In the circuit, the
resistors at the LT1671’s positive input set a DC bias point.
The 2k-0.068µF path sets up phase shifted feedback and
the circuit looks like a wideband unity-gain follower at DC.
The crystal’s path provides resonant positive feedback
and stable oscillation occurs.
Figure 8 permits crystals to be electronically switched by
logic commands. This circuit is similar to the previous
examples, except that oscillation is only possible when
one of the logic inputs is biased high.
XTAL X
RX
DX
XTAL B
5V
LOGIC INPUTS
AS MANY STAGES
AS DESIRED
1k
B
2k
1MHz TO 10MHz
CRYSTAL (AT-CUT)
5V
XTAL A
1k
A
1k
LT1671
2k
D1
+
+
OUTPUT
–
–
OUTPUT
LT1671
1k
D2
2k
2k
1671 F08
1671 F07
0.068µF
75pF
= 1N4148
GROUND XTAL CASES
Figure 7. 1MHz to 10MHz Crystal Oscillator
10
Figure 8. Switchable Output Crystal Oscillator. Biasing A or B
High Places Associated Crystal in Feedback Path. Additional
Crystal Branches Are Permissible
LT1671
U
PACKAGE DESCRIPTION
Dimensions in inches (millimeters) unless otherwise noted.
MS8 Package
8-Lead Plastic MSOP
(LTC DWG # 05-08-1660)
0.118 ± 0.004*
(3.00 ± 0.102)
8
7 6
5
0.118 ± 0.004**
(3.00 ± 0.102)
0.192 ± 0.004
(4.88 ± 0.10)
1
2 3
4
0.040 ± 0.006
(1.02 ± 0.15)
0.007
(0.18)
0.034 ± 0.004
(0.86 ± 0.102)
0° – 6° TYP
SEATING
PLANE 0.012
(0.30)
0.0256
REF
(0.65)
TYP
0.021 ± 0.006
(0.53 ± 0.015)
0.006 ± 0.004
(0.15 ± 0.102)
MSOP (MS8) 1197
* DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
S8 Package
8-Lead Plastic Small Outline (Narrow 0.150)
(LTC DWG # 05-08-1610)
0.189 – 0.197*
(4.801 – 5.004)
8
7
6
5
0.150 – 0.157**
(3.810 – 3.988)
0.228 – 0.244
(5.791 – 6.197)
1
0.010 – 0.020
× 45°
(0.254 – 0.508)
0.008 – 0.010
(0.203 – 0.254)
0.053 – 0.069
(1.346 – 1.752)
0°– 8° TYP
0.016 – 0.050
0.406 – 1.270
0.014 – 0.019
(0.355 – 0.483)
2
3
4
0.004 – 0.010
(0.101 – 0.254)
0.050
(1.270)
TYP
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
SO8 0996
11
LT1671
U
TYPICAL APPLICATION
LT1671’s positive input. The LT1671’s negative input is
biased directly from A1’s output. The LT1671’s output, the
circuit’s output, is unaffected by > 85:1 signal amplitude
variations. Bandwidth limiting in A1 does not affect triggering because the adaptive trigger threshold varies
ratiometrically to maintain circuit output.
4MHz Adaptive Trigger Circuit
Line and fiber-optic receivers often require an adaptive
trigger to compensate for variations in signal amplitude
and DC offsets. The circuit in Figure 9 triggers on 2mV to
175mV signal from 100Hz to 4MHz while operating from
a single 5V rail. A1, operating at a gain of 15, provides
wideband AC gain. The output of this stage biases a 2-way
peak detector (Q1 through Q4). The maximum peak is
stored in Q2’s emitter capacitor, while the minimum
excursion is retained in Q4’s emitter capacitor. The DC
value of the midpoint of A1’s output signal appears at the
junction of the 500pF capacitor and the 3MΩ units. This
point always sits midway between the signal’s excursions,
regardless of absolute amplitude. This signal-adaptive
voltage is buffered by A2 to set the trigger voltage at the
Figure 10 shows operating waveforms at 4MHz. Trace A’s
input produces Trace B’s amplified output at A1. The
comparator’s output is Trace C.
A = 10mV/DIV
B = 50mV/DIV
C = 1mV/DIV
5V
2k
50ns/DIV
3
Q1
1
5
2
5V
1671F10
6
Q2
4
3M
+
0.005µF
A1
LT1227
750ΩΩ
5V
+
–
13
2k
500pF
0.005µF
–
510ΩΩ
36ΩΩ
12
15
A2
LT1006
3M
10
14
Q3
5V
Figure 10. Adaptive Trigger
Responding to a 4MHz, 5mV Input.
Input Amplitude Variations from 2mV
to 175mV Are Accommodated
Q4
11
470ΩΩ
+
10µF +
0.1µF
100µF
0.1µF
+
2k
0.1µF
470Ω
–
LT1671
TRIGGER
OUT
INPUT
1671 F09
Q1, Q2, Q3, Q4 = CA3096 ARRAY: TIE SUBSTRATE (PIN 16) TO GROUND
= 1N4148
Figure 9. 4MHz Single Supply Adaptive Trigger. Output Comparator’s Threshold Varies Ratiometrically with
Input Amplitude, Maintaining Data Integrity over >85:1 Input Amplitude Range
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1016
UltraFastTM Precision Comparator
Industry Standard 10ns Comparator
LT1116
12ns Single Supply Ground-Sensing Comparator
Single Supply Version of LT1016
LT1394
UltraFast Single Supply Comparator
7ns, 6mA Single Supply Comparator
LT1720
UltraFast Dual Single Supply Comparator
Dual 4.5ns, 4mA Single Supply Comparator
UltraFast is a trademark of Linear Technology Corporation.
12
Linear Technology Corporation
1671fs, sn1671 LT/TP 0499 4K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408)432-1900 ● FAX: (408) 434-0507 ● www.linear-tech.com
 LINEAR TECHNOLOGY CORPORATION 1998
Similar pages