Maxim MAX7480ESA 8th-order, lowpass, butterworth, switched-capacitor filter Datasheet

19-1416; Rev 0; 1/99
8th-Order, Lowpass, Butterworth,
Switched-Capacitor Filter
The MAX7480 8th-order, lowpass, Butterworth,
switched-capacitor filter (SCF) operates from a single
+5V supply. The device draws only 2.9mA of supply
current and allows corner frequencies from 1Hz to
2kHz, making it ideal for low-power post-DAC filtering
and anti-aliasing applications. The MAX7480 features a
shutdown mode, which reduces the supply current to
0.2µA.
Two clocking options are available: self-clocking
(through the use of an external capacitor) or external
clocking for tighter corner-frequency control. An offset
adjust pin allows for adjustment of the DC output level.
The MAX7480 Butterworth filter provides a maximally
flat passband response. The fixed response simplifies
the design task to selecting a clock frequency.
Features
♦ 8th-Order, Lowpass Butterworth Filter
♦ Low Noise and Distortion: -73dB THD + Noise
♦ Clock-Tunable Corner Frequency (1Hz to 2kHz)
♦ 100:1 Clock-to-Corner Ratio
♦ +5V Single-Supply Operation
♦ Low Power
2.9mA (Operating Mode)
0.2µA (Shutdown Mode)
♦ Available in 8-Pin SO/DIP Package
♦ Low Output Offset: ±5mV
Ordering Information
Applications
ADC Anti-Aliasing
PART
MAX7480ESA
MAX7480EPA
Post-DAC Filtering
Pin Configuration
TEMP. RANGE
PIN-PACKAGE
-40°C to +85°C
-40°C to +85°C
8 SO
8 Plastic DIP
Typical Operating Circuit
TOP VIEW
VSUPPLY
COM 1
8
CLK
7
SHDN
3
6
OS
VDD 4
5
OUT
IN 2
0.1µF
VDD
SHDN
MAX7480
GND
SO/DIP
INPUT
IN
OUT
OUTPUT
MAX7480
CLOCK
COM
CLK
GND
OS
0.1µF
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
MAX7480
General Description
MAX7480
8th-Order, Lowpass, Butterworth,
Switched-Capacitor Filter
ABSOLUTE MAXIMUM RATINGS
VDD to GND ..............................................................-0.3V to +6V
IN, OUT, COM, OS, CLK ............................-0.3V to (VDD + 0.3V)
SHDN........................................................................-0.3V to +6V
OUT Short-Circuit Duration...................................................1sec
Continuous Power Dissipation (TA = +70°C)
8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
8-Pin DIP (derate 9.09mW/°C above +70°C) ...............727mW
Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDD = +5V, filter output measured at OUT, 10kΩ || 50pF load to GND at OUT, OS = COM, 0.1µF from COM to GND, SHDN =
VDD, fCLK = 100kHz, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
FILTER CHARACTERISTICS
Corner Frequency
Clock-to-Corner Ratio
fC
(Note 1)
0.001 to 2
fCLK / fC
Clock-to-Corner Tempco
10
Output Voltage Range
Output Offset Voltage
0.25
VOFFSET
DC Insertion Gain with
Output Offset Removed
THD+N
OS Voltage Gain to OUT
Input Voltage Range at OS
Input Resistance at COM
ppm/°C
VDD - 0.25
VIN = VCOM = VDD / 2
VCOM = VDD / 2 (Note 2)
Total Harmonic Distortion
plus Noise
COM Voltage Range
kHz
100:1
-0.1
fIN = 200Hz, VIN = 4Vp-p,
measurement bandwidth = 22kHz
V
±5
±25
mV
0.15
0.3
dB
-73
dB
AOS
1
V/ V
VOS
VCOM ±0.1
V
Input, COM externally driven
VDD / 2
- 0.5
VDD / 2 VDD / 2
+ 0.5
Output, COM internally biased
VDD / 2
- 0.2
VDD / 2 VDD / 2
+ 0.2
VCOM
V
RCOM
75
Resistive Output Load Drive
RL
10
Maximum Capacitive Load at
OUT
CL
50
Clock Feedthrough
125
kΩ
10
mVp-p
1
kΩ
500
pF
Input Leakage Current at COM
SHDN = GND, VCOM = 0 to VDD
±0.1
±10
µA
Input Leakage Current at OS
VOS = 0 to (VDD - 1V) (Note 3)
±0.1
±10
µA
53
67
kHz
±24
±40
µA
CLOCK
Internal Oscillator Frequency
fOSC
COSC = 1000pF (Note 4)
Clock Input Current
ICLK
VCLK = 0 or 5V
Clock Input High
VIH
Clock Input Low
VIL
2
40
VDD - 0.5
_______________________________________________________________________________________
V
0.5
V
8th-Order, Lowpass, Butterworth,
Switched-Capacitor Filter
(VDD = +5V, filter output measured at OUT, 10kΩ || 50pF load to GND at OUT, OS = COM, 0.1µF from COM to GND, SHDN =
VDD, fCLK = 100kHz, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
5.5
V
mA
POWER REQUIREMENTS
Supply Voltage
VDD
Supply Current
IDD
4.5
Operating mode, no load, IN = OS = COM
2.9
3.5
Shutdown Current
I SHDN
SHDN = GND, CLK driven from 0 to VDD
0.2
1
Power-Supply Rejection Ratio
PSRR
Measured at DC
60
µA
dB
SHUTDOWN
SHDN Input High
VSDH
SHDN Input Low
VSDL
SHDN Input Leakage Current
VDD - 0.5
V
±0.1
V SHDN = 0 to VDD
0.5
V
±10
µA
FILTER CHARACTERISTICS
(VDD = +5V, filter output measured at OUT, 10kΩ || 50pF load to GND at OUT, SHDN = VDD, VCOM = VOS = VDD /2, fCLK = 100kHz, TA
= TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
Insertion Gain Relative to
DC Gain
CONDITIONS
MIN
TYP
fIN = 0.5fC
-0.1
0.0
MAX
fIN = fC
-3.5
-3.0
-2.5
fIN = 2fC
-48
-43
fIN = 3fC
-76
-70
UNITS
dB
Note 1: The maximum fC is defined as the clock frequency fCLK = 100 · fC at which the peak SINAD drops to 68dB with a sinusoidal
input at 0.2fC.
Note 2: DC insertion gain is defined as ∆VOUT / ∆VIN.
Note 3: OS voltages above VDD - 1V saturate the input and result in a 75µA typical input leakage current.
Note 4: fOSC (kHz) ≅ 53 · 103 / COSC (pF).
_______________________________________________________________________________________
3
MAX7480
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(VDD = +5V, fCLK = 100kHz, SHDN = VDD, VCOM = VOS = VDD / 2, TA = +25°C, unless otherwise noted.)
-0.5
-1.5
-2.0
-80
-2.5
-100
606
808
SUPPLY CURRENT vs. TEMPERATURE
MAX7480 toc04
2.80
NO LOAD
2.95
2.90
2.85
2.80
2.75
2.75
2.70
2.70
1200
1600
2000
2.0
VIN = VCOM
1.5
1.0
0.5
0
-0.5
-1.0
-1.5
-2.0
-40
4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
800
DC OFFSET VOLTAGE
vs. SUPPLY VOLTAGE
DC OFFSET VOLTAGE (mV)
2.85
400
INPUT FREQUENCY (Hz)
3.00
SUPPLY CURRENT (mA)
2.90
0
1010
SUPPLY CURRENT vs. SUPPLY VOLTAGE
2.95
-20
0
20
40
60
80
100
4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
SUPPLY VOLTAGE (V)
TEMPERATURE (°C)
SUPPLY VOLTAGE (V)
OFFSET VOLTAGE vs. TEMPERATURE
INTERNAL OSCILLATOR FREQUENCY vs.
COSC CAPACITANCE
NORMALIZED INTERNAL OSCILLATOR
FREQUENCY vs. SUPPLY VOLTAGE
FREQUENCY (kHz)
0.5
100
0
-0.5
10
1
-1.0
0.1
-1.5
0.01
-40
-20
0
20
40
60
TEMPERATURE (°C)
80
100
1.05
NORMALIZED OSCILLATOR FREQUENCY
VIN = VCOM = VDD / 2
1000
MAX7401 toc07
1.0
MAX7480 toc08
SUPPLY CURRENT (mA)
404
INPUT FREQUENCY (Hz)
NO LOAD
4
202
INPUT FREQUENCY (kHz)
3.00
480
640
0
MAX7480 toc05
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
400
fC = 1kHz
-3.5
0
320
560
-3.0
-120
240
MAX7480-06
-60
-1.0
160
COSC = 530pF
1.04
MAX7480-09
GAIN (dB)
GAIN (dB)
-40
fC = 1kHz
80
PHASE SHIFT (DEGREES)
0
-20
0
MAX7480 toc02
MAX7480 toc01
fC = 1kHz
0
PHASE RESPONSE
PASSBAND FREQUENCY RESPONSE
0.5
MAX7480 toc03
FREQUENCY RESPONSE
20
OFFSET VOLTAGE (mV)
MAX7480
8th-Order, Lowpass, Butterworth,
Switched-Capacitor Filter
1.03
1.02
1.01
1.00
0.99
0.98
0.97
0.96
0.95
0.1
1
10
CAPACITANCE (nF)
100
1000
4.5 4.6 4.7 4.8 4.9 5.0 5.1 5.2 5.3 5.4 5.5
SUPPLY VOLTAGE (V)
_______________________________________________________________________________________
8th-Order, Lowpass, Butterworth,
Switched-Capacitor Filter
(VDD = +5V, fCLK = 100kHz, SHDN = VDD, VCOM = VOS = VDD / 2, TA = +25°C, unless otherwise noted.)
NORMALIZED OSCILLATOR FREQUENCY
vs. TEMPERATURE
1.02
0
NO LOAD
(SEE TABLE A)
-10
-20
MAX7480 toc11
COSC = 530pF
MAX7480 toc10
-30
1.01
THD+N (dB)
NORMALIZED OSCILLATOR FREQUENCY
1.03
TOTAL HARMONIC DISTORTION PLUS NOISE
vs. INPUT SIGNAL AMPLITUDE
1
-40
-50
A
-60
0.99
B
-70
0.98
-80
-90
0.97
-40
-20
0
20
40
60
80
100
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
TEMPERATURE (°C)
AMPLITUDE (Vp-p)
Table A. THD+N vs. Input Signal
Amplitude Test Conditions
TRACE
fIN
(Hz)
fC
(kHz)
fCLK
(kHz)
MEASUREMENT
BANDWIDTH (kHz)
A
400
2
200
22
B
200
1
100
22
_______________________________________________________________________________________
5
MAX7480
Typical Operating Characteristics (continued)
MAX7480
8th-Order, Lowpass, Butterworth,
Switched-Capacitor Filter
Pin Description
PIN
NAME
1
COM
FUNCTION
Common Input Pin. Biased internally at mid-supply. Bypass externally to GND with a 0.1µF capacitor. To
override internal biasing, drive with an external supply.
2
IN
3
GND
Filter Input
Ground
4
VDD
+5V Supply Input
5
OUT
Filter Output
6
OS
7
SHDN
8
CLK
Offset Adjust Input. To adjust output offset, bias OS externally. Connect OS to COM if no offset adjustment is
needed. Refer to Offset and Common-Mode Input Adjustment section.
Shutdown Input. Drive low to enable shutdown mode; drive high or connect to VDD for normal operation.
Clock Input. To override the internal oscillator, connect to an external clock; otherwise, connect an external
capacitor (COSC) from CLK to GND to set the internal oscillator frequency.
_______________Detailed Description
The MAX7480 Butterworth filter operates with a 100:1
clock-to-corner frequency ratio and a 2kHz maximum
corner frequency.
Lowpass Butterworth filters provide a maximally flat
passband response, making them ideal for instrumentation applications that require minimum deviation from
the DC gain throughout the passband.
Figure 1 shows the difference between Bessel and
Butterworth filter frequency responses. With the filter
cutoff frequencies set at 1kHz, trace A shows the
Bessel filter response and trace B shows the
Butterworth filter response.
20
0
GAIN (dB)
-20
A switched-capacitor filter such as the MAX7480 emulates a passive ladder filter. The filter’s component sensitivity is low when compared to a cascaded biquad
design, because each component affects the entire filter shape, not just one pole-zero pair. In other words, a
mismatched component in a biquad design will have a
concentrated error on its respective poles, while the
same mismatch in a ladder filter design results in an
error distributed over all poles.
6
B
-60
-80
-100
Background Information
Most switched-capacitor filters (SCFs) are designed
with biquadratic sections. Each section implements two
filtering poles, and the sections are cascaded to produce higher-order filters. The advantage to this
approach is ease of design. However, this type of
design is highly sensitive to component variations if any
section’s Q is high. An alternative approach is to emulate a passive network using switched-capacitor integrators with summing and scaling. Figure 2 shows a
basic 8th-order ladder filter structure.
A
-40
0.1
0.2
0.5
1
2
5
10
FREQUENCY (kHz)
A: BESSEL FILTER RESPONSE; fC = 1kHz
B: BUTTERWORTH FILTER RESPONSE; fC = 1kHz
Figure 1. Bessel vs. Butterworth Filter Frequency Response
R1
+
-
VIN
L1
L5
L3
C2
C4
L7
C6
Figure 2. 8th-Order Ladder Filter Network
_______________________________________________________________________________________
C8
R2
V0
8th-Order, Lowpass, Butterworth,
Switched-Capacitor Filter
External Clock
The MAX7480 SCF is designed for use with external
clocks that have a 40% to 60% duty cycle. When using
an external clock with these devices, drive CLK with a
CMOS gate powered from 0 to VDD. Varying the rate of
the external clock adjusts the corner frequency of the
filter as follows:
fC = fCLK / 100
Internal Clock
When using the internal oscillator, connect a capacitor
(COSC) between CLK and ground. The value of the
capacitor determines the oscillator frequency as follows:
53 ⋅10
; COSC in pF
COSC
3
fOSC (kHz) =
Minimize the stray capacitance at CLK so that it does
not affect the internal oscillator frequency. Vary the rate
of the internal oscillator to adjust the filter’s corner frequency by a 100:1 clock to corner-frequency ratio. For
example, an internal oscillator frequency of 100kHz
produces a nominal corner frequency of 1kHz.
connect OS to COM. For applications requiring offset
adjustment or DC level shifting, apply an external bias
voltage through a resistor-divider network to OS, as
shown in Figure 3. (Note: Do not leave OS unconnected.) The output voltage is represented by this equation:
VOUT = (VIN - VCOM) + VOS
with VCOM = VDD / 2 (typical), where (VIN - VCOM) is
lowpass-filtered by the SCF and VOS is added at the
output stage. See the Electrical Characteristics for the
voltage range of COM and OS. Changing the voltage
on COM or OS significantly from mid-supply reduces
the filter’s dynamic range.
Power Supplies
The MAX7480 operates from a single +5V supply.
Bypass VDD to GND with a 0.1µF capacitor. If dual
supplies (±2.5V) are required, connect COM to system
ground and connect GND to the negative supply.
Figure 4 shows an example of dual-supply operation.
Single- and dual-supply performances are equivalent.
For either single- or dual-supply operation, drive CLK
and SHDN from GND (V- in dual-supply operation) to
V DD . For ±5V dual-supply applications, use the
MAX291–MAX297.
Input Impedance vs. Clock Frequencies
The MAX7480’s input impedance is effectively that of a
switched-capacitor resistor, and is inversely proportional to frequency. The input impedance values determined below represent the average input impedance,
since the input current is not continuous. As a rule, use
a driver with an output impedance less than 10% of the
filter’s input impedance. Estimate the input impedance
of the filter using the following formula:
ZIN =
(
1
fCLK ⋅ CIN
)
where fCLK = clock frequency and CIN = 2.31pF.
Input Signal Amplitude Range
The optimal input signal range is determined by observing the voltage level at which the total harmonic distortion plus noise (THD+N) is minimized for a given corner
frequency. The Typical Operating Characteristics
shows a graph of the device’s THD+N response as the
input signal’s peak-to-peak amplitude is varied. This
measurement is made with OS and COM biased at midsupply.
VSUPPLY
0.1µF
VDD
Low-Power Shutdown Mode
This device features a shutdown mode that is activated
by driving SHDN low. In shutdown mode, the filter’s supply current reduces to 0.2µA (typ) and its output
becomes high impedance. For normal operation, drive
SHDN high or connect to VDD.
___________Applications Information
Offset and Common-Mode
Input Adjustment
The voltage at COM sets the common-mode input voltage and is biased at mid-supply with an internal resistor-divider. Bypass COM with a 0.1µF capacitor and
INPUT
IN
SHDN
OUT
OUTPUT
COM
0.1µF
50k
MAX7480
CLOCK
CLK
50k
OS
0.1µF
GND
50k
Figure 3. Offset Adjustment Circuit
_______________________________________________________________________________________
7
MAX7480
Clock Signal
MAX7480
8th-Order, Lowpass, Butterworth,
Switched-Capacitor Filter
Anti-Aliasing and Post-DAC Filtering
V+ = +2.5V
When using the MAX7480 for anti-aliasing or post-DAC
filtering, synchronize the DAC and the filter clocks. If
the clocks are not synchronized, beat frequencies may
alias into the passband.
The high clock-to-corner frequency ratio (100:1) also
eases the requirements of pre- and post-SCF filtering.
At the input, a lowpass filter prevents the aliasing of frequencies around the clock frequency into the passband. At the output, a lowpass filter attenuates the
clock feedthrough.
A high clock to corner-frequency ratio allows a simple
RC lowpass filter, with the cutoff frequency set above
the SCF corner frequency to provide input anti-aliasing
and reasonable output clock attenuation.
VDD
OUT
INPUT
V+
V-
IN
*
OUTPUT
COM
MAX7480
CLOCK
CLK
OS
0.1µF
0.1µF
GND
V- = -2.5V
Harmonic Distortion
Harmonic distortion arises from nonlinearities within the
filter. These nonlinearities generate harmonics when a
pure sine wave is applied to the filter input. Table 1 lists
the MAX7480’s typical harmonic-distortion values with
a 10kΩ load at TA = +25°C.
SHDN
*DRIVE SHDN TO V- FOR LOW-POWER SHUTDOWN MODE.
Figure 4. Dual-Supply Operation
Table 1. Typical Harmonic Distortion
FILTER
fCLK
(kHz)
fC
(kHz)
fIN
(Hz)
100
1
200
MAX7480
VIN
(Vp-p)
TYPICAL HARMONIC DISTORTION (dB)
2nd
3rd
4th
5th
-89
-73
-91
-93
-82
-68
-85
-89
4
200
2
400
Chip Information
TRANSISTOR COUNT: 1116
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1999 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Similar pages