HD74LV139A Dual 2-to-4 line Decoder / Demultiplexers ADE-205-262 (Z) 1st Edition March 1999 Description The HD74LV139A is designed to be used in high-performance memory-decoding or data-routing applications requiring very short propagation delay times. The active-low enable input can be used as a data line in demultiplexing applications. This decoder/demultiplexer features fully buffered inputs, each of which represents only one normalized load to its driving circuit. Low-voltage and high-speed operation is suitable for the battery-powered products (e.g., notebook computers), and the low-power consumption extends the battery life. Features • • • • • • VCC = 2.0 V to 5.5 V operation All inputs VIH (Max.) = 5.5 V (@VCC = 0 V to 5.5 V) All outputs VO (Max.) = 5.5 V (@VCC = 0 V) Typical VOL ground bounce < 0.8 V (@VCC = 3.3 V, Ta = 25°C) Typical VOH undershoot > 2.3 V (@VCC = 3.3 V, Ta = 25°C) Output current ±6 mA (@VCC = 3.0 V to 3.6 V), ±12 mA (@VCC = 4.5 V to 5.5 V) Function Table Inputs Select Outputs G1 B A Y0 Y1 Y2 Y3 H X X H H H H L L L L H H H L L H H L H H L H L H H L H L H H H H H L Note: H: High level L: Low level X: Immaterial HD74LV139A Pin Arrangement 1G 1 16 VCC 1A 2 15 2G 1B 3 14 2A 1Y0 4 13 2B 1Y1 5 12 2Y0 1Y2 6 11 2Y1 1Y3 7 10 2Y2 GND 8 9 2Y3 (Top view) Absolute Maximum Ratings Item Supply voltage range Input voltage range* 1 Output voltage range* 1, 2 Symbol Ratings Unit VCC –0.5 to 7.0 V VI –0.5 to 7.0 V VO –0.5 to VCC + 0.5 V –0.5 to 7.0 Conditions Output: H or L VCC: OFF Input clamp current I IK –20 mA VI < 0 Output clamp current I OK ±50 mA VO < 0 or VO > VCC Continuous output current IO ±25 mA VO = 0 to VCC Continuous current through VCC or GND I CC or IGND ±50 mA Maximum power dissipation at Ta = 25°C (in still air)*3 PT 785 mW 500 Storage temperature Tstg –65 to 150 SOP TSSOP °C Notes: The absolute maximum ratings are values which must not individually be exceeded, and furthermore, no two of which may be realized at the same time. 1. The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. This value is limited to 5.5 V maximum. 3. The maximum package power dissipation was calculated using a junction temperature of 150°C. 2 HD74LV139A Recommended Operating Conditions Item Symbol Min Max Unit Supply voltage range VCC 2.0 5.5 V Input voltage range VI 0 5.5 V Output voltage range VO 0 VCC V H or L Output current I OH — –50 µA VCC = 2.0 V — –2 mA VCC = 2.3 to 2.7 V — –6 VCC = 3.0 to 3.6 V — –12 VCC = 4.5 to 5.5 V — 50 µA VCC = 2.0 V — 2 mA VCC = 2.3 to 2.7 V — 6 VCC = 3.0 to 3.6 V — 12 VCC = 4.5 to 5.5 V 0 200 0 100 VCC = 3.0 to 3.6 V 0 20 VCC = 4.5 to 5.5 V –40 85 I OL Input transition rise or fall rate Operating free-air temperature ∆t/∆v Ta ns/V Conditions VCC = 2.3 to 2.7 V °C Note: Unused or floating inputs must be held high or low. 3 HD74LV139A Logic Diagram 4 1G 1A Select inputs 1B 5 1Y1 6 1Y2 7 1Y3 2 3 Data outputs 12 2G 10 4 2A 2B 2Y0 15 11 Select inputs 1Y0 1 2Y1 2Y2 14 13 9 2Y3 HD74LV139A DC Electrical Characteristics • Ta = –40 to 85°C Item Symbol VCC (V)* Min Typ Max Unit Input voltage VIH 2.0 1.5 — — V 2.3 to 2.7 VCC × 0.7 — — 3.0 to 3.6 VCC × 0.7 — — 4.5 to 5.5 VCC × 0.7 — — 2.0 — — 0.5 2.3 to 2.7 — — VCC × 0.3 3.0 to 3.6 — — VCC × 0.3 4.5 to 5.5 — — VCC × 0.3 Min to Max VCC – 0.1 — — 2.3 2.0 — — IOH = –2 mA 3.0 2.48 — — IOH = –6 mA 4.5 3.8 — — IOH = –12 mA Min to Max — — 0.1 IOL = 50 µA 2.3 — — 0.4 IOL = 2 mA 3.0 — — 0.44 IOL = 6 mA 4.5 — — 0.55 IOL = 12 mA VIL Output voltage VOH VOL V Test Conditions IOH = –50 µA Input current IIN 0 to 5.5 — — ±1 µA VI = 5.5 V or GND Quiescent supply current ICC 5.5 — — 20 µA VI = VCC or GND, IO = 0 Output leakage current IOFF 0 — — 5 µA VI or VO = 0 V to 5.5 V Input capacitance CIN 3.3 — 1.9 — pF VI = VCC or GND Note: For conditions shown as Min or Max, use the appropriate values under recommended operating conditions. 5 HD74LV139A Switching Characteristics • VCC = 2.5 ± 0.2 V Ta = 25°C Ta = –40 to 85°C Item Symbol Min Typ Max Min Max Unit Test Conditions FROM (Input) TO (Output) Propagation delay time tPLH/tPHL — 7.7 17.6 1.0 21.0 ns CL = 15 pF A or B Y — 10.2 22.5 1.0 26.5 CL = 50 pF — 7.4 15.8 1.0 19.0 CL = 15 pF — 9.9 20.2 1.0 24.0 CL = 50 pF G • VCC = 3.3 ± 0.3 V Ta = 25°C Ta = –40 to 85°C Item Symbol Min Typ Max Min Max Unit Test Conditions FROM (Input) TO (Output) Propagation delay time tPLH/tPHL — 5.3 11.0 1.0 13.0 ns CL = 15 pF A or B Y — 7.3 14.5 1.0 16.5 CL = 50 pF — 5.1 9.2 1.0 11.0 CL = 15 pF — 7.0 12.7 1.0 14.5 CL = 50 pF G • VCC = 5.0 ± 0.5 V Ta = 25°C Ta = –40 to 85°C Item Symbol Min Typ Max Min Max Unit Test Conditions FROM (Input) TO (Output) Propagation delay time tPLH/tPHL — 3.7 7.2 1.0 8.5 ns CL = 15 pF A or B Y — 5.2 9.2 1.0 10.5 CL = 50 pF — 3.5 6.3 1.0 7.5 CL = 15 pF — 4.9 8.3 1.0 9.5 CL = 50 pF 6 G HD74LV139A Operating Characteristics • CL = 50 pF Ta = 25°C Item Symbol VCC (V) Min Typ Max Unit Test Conditions Power dissipation capacitance CPD 3.3 — 17.3 — pF f = 10 MHz 5.0 — 18.2 — Test Circuit Measurement point CL* Note: C L includes the probe and jig capacitance. 7 HD74LV139A • Waveform tr Input 10% tf 90% 50% VCC 90% 50% VCC VCC 10% t PHL t PLH 0V VOH In phase output 50% VCC 50% VCC VOL t PHL t PLH VOH Out of phase output 50% VCC 50% VCC VOL Notes: 1. Input waveform: PRR ≤ 1 MHz, Zo = 50 Ω, t r ≤ 3 ns, tf ≤ 3 ns 2. The output is measured one at a time with one transition per measurement. 8 HD74LV139A Package Dimensions 10.06 10.5 Max 9 1 8 1.27 0.42 ± 0.08 0.40 ± 0.06 0.10 ± 0.10 0.80 Max 0.22 ± 0.05 0.20 ± 0.04 2.20 Max 5.5 16 0.20 7.80 +– 0.30 1.15 0° – 8° 0.70 ± 0.20 0.15 0.12 M Dimension including the plating thickness Base material dimension Hitachi Code JEDEC EIAJ Weight (reference value) FP-16DA — Conforms 0.24 g 9 HD74LV139A Unit: mm 9.9 10.3 Max 9 1 8 0.635 Max 0.42 ± 0.08 0.40 ± 0.06 0.15 *0.22 ± 0.03 0.20 ± 0.03 1.27 0.11 0.14 +– 0.04 1.75 Max 3.95 16 0.10 6.10 +– 0.30 1.08 0° – 8° + 0.67 0.60 – 0.20 0.25 M Dimension including the plating thickness Base material dimension 10 Hitachi Code JEDEC EIAJ Weight (reference value) FP-16DN Conforms Conforms 0.15 g HD74LV139A 5.0 5.3 Max 9 1 8 4.40 16 0.65 0.13 M 1.10 Max 0.65 Max 0.10 Dimension including the plating thickness Base material dimension 6.40 ± 0.20 0.07 +0.03 –0.04 0.20 ± 0.06 1.0 0.17 ± 0.05 0.15 ± 0.04 0.08 0.22 +– 0.07 0° – 8° 0.50 ± 0.10 Hitachi Code JEDEC EIAJ Weight (reference value) TTP-16DA — — 0.05 g 11 Cautions 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with third party’s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However, contact Hitachi’s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the Hitachi product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Hitachi. 7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor products. Hitachi, Ltd. Semiconductor & Integrated Circuits. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109 URL NorthAmerica : http:semiconductor.hitachi.com/ Europe : http://www.hitachi-eu.com/hel/ecg Asia (Singapore) : http://www.has.hitachi.com.sg/grp3/sicd/index.htm Asia (Taiwan) : http://www.hitachi.com.tw/E/Product/SICD_Frame.htm Asia (HongKong) : http://www.hitachi.com.hk/eng/bo/grp3/index.htm Japan : http://www.hitachi.co.jp/Sicd/indx.htm For further information write to: Hitachi Semiconductor (America) Inc. 179 East Tasman Drive, San Jose,CA 95134 Tel: <1> (408) 433-1990 Fax: <1>(408) 433-0223 Hitachi Europe GmbH Electronic components Group Dornacher Stra§e 3 D-85622 Feldkirchen, Munich Germany Tel: <49> (89) 9 9180-0 Fax: <49> (89) 9 29 30 00 Hitachi Europe Ltd. Electronic Components Group. Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA, United Kingdom Tel: <44> (1628) 585000 Fax: <44> (1628) 778322 Hitachi Asia Pte. Ltd. 16 Collyer Quay #20-00 Hitachi Tower Singapore 049318 Tel: 535-2100 Fax: 535-1533 Hitachi Asia Ltd. Taipei Branch Office 3F, Hung Kuo Building. No.167, Tun-Hwa North Road, Taipei (105) Tel: <886> (2) 2718-3666 Fax: <886> (2) 2718-8180 Hitachi Asia (Hong Kong) Ltd. Group III (Electronic Components) 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: <852> (2) 735 9218 Fax: <852> (2) 730 0281 Telex: 40815 HITEC HX Copyright ' Hitachi, Ltd., 1999. All rights reserved. Printed in Japan.