Pan Jit GBU6G Glass passivated single-phase bridge rectifier(voltage - 100 volts current - 6.0 amperes) Datasheet

DATA SHEET
GBU6A~GBU6K
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
GBU
VOLTAGE - 100 Volts CURRENT - 6.0 Amperes
FEATURES
.310(7.90)
.290(7.40)
• Plastic material has Underwriters Laboratory
Flammability Classification 94V-O
• Ideal for printed circuit board
Unit: inch ( mm )
.880(22.3)
.860(21.8)
.160(4.1)
.140(3.5)
.140(3.56)
.130(3.30)
.075(1.90)R
.085(2.16)
.065(1.65)
• High temperature soldering guaranteed:
260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: Reliable low cost construction utilizing
.100(2.54)
.085(2.16)
molded plastic technique
Terminals: Leads solderable per MIL-STD-202,
.740(18.8)
.720(18.3)
• Surge overload rating: 175 Amperes peak
.710(18.0)
.690(17.5)
.080(2.03)
.060(1.52)
• Reliable low cost construction utilizing molded plastic technique
.040(1.02)
.030(0.76)
.022(0.56)
.018(0.46)
.080(2.03)
.065(1.65)
Method 208
Mounting position: Any
.190(4.83)
.210(5.33)
Mounting torque: 5 in. lb. Max.
.050(1.27)
.040(1.02)
Weight: 0.15 ounce, 4.0 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz.
For Capacitive load derate current by 20%.
GBU6A
GBU6B
GBU6D
GBU6G
GBU6J
GBU6K
UNIT
Maximum Recurrent Peak Reverse Voltage
50
100
200
400
600
800
V
Maximum RMS Input Voltage
35
70
140
280
420
560
V
Maximum DC Blocking Voltage
50
100
200
400
600
800
V
Maximum Average Forward TC=100°C
6.0
A
127
A2sec
175
Apk
Maximum Instantaneous Forward Voltage Drop per element at 3.0A
1.0
Vpk
Maximum Reverse Leakage at rated TA=25°
CDc Blocking Voltage per element TC=100°C
5.0
500
µA
µA
Typical Thermal Resistance per leg(Note 2) RθJA
8.6
°C / W
Typical Thermal Resistance per leg(Note 3) RθJC
3.1
°C / W
-55+150
°C
Rectified Output Current at
I2t Rating for fusing ( t<8.35ms)
Peak Forward Surge Current single sine-wave superimposed on rated
load(JEDEC method)
Operating and Storage Temperature Range, TJ,TSTG
NOTES:
1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw.
2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads.
3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate.
DATE : SEP.16.2002
PAGE . 1
INSTANTANEOUS FORWARD CURRENT, AMPERES
AVERAGE FORWARD CURRENT
AMPERES
RATING AND CHARACTERISTIC C URVES
6.0
HEAT-SINK
MOUNTING,TC
(4 4 0 .15) INCH
COPPER PLATE
4.0
2.0
MOUNTED ON PC BOARD.
TA 0.5"(12.7mm) LEAD LENGTH
60Hz RESISTIVE OR INDUCTIVE LOAD
100
40
20
10
4.0
1.0
0.4
0.2
0
0
50
100
0.1
0.7
150
TEMPERATUREOC
FPRWARD SURGE CURRENT, AMPERES pk
(HALF SINE-WAVE)
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
10
O
TC = 100 C
1.0
0.1
O
TA= 25 C
0.01
20
40
60
80
100
120
0.8
0.9
1.0
1.1
1.2
1.3
1.4
INSTANTANEOUS FORWARD VOLTAGE, VOLTS
Fig . 1- DERATING C URVE FOR OUTPUT RECTIFIED CURRENT
0
O
TJ= 25 C
Pulse Wid th= 300 S
1% DULY Cyc le
2.0
140
PERCENT OF PEAK REVERSE VOLTAGE
Fig . 2- TYPICAL INSTANTANEOUS FORWARD
CHARACTERIS ITCS PER ELEMENT
175
140
105
70
O
TA= 105 C
35
0
1
2
6
10
20
40
60
100
NO. OF CYCLES AT 62Hz
Fig . 3- TYPICAL REAK REVERSE CHARACTER ISTICS
Fig . 4- MAXIMUM NON-REPETITEVE PEAK
FORWARD SURGE CURRENT
CAPACITANCE, p F
400
100
O
Tj= 25 C
f= 1.0MHz
Vsig = 50mVp -p
50
10
1
5
10
50
100
REVERSE VOLTAGE, VOLTS
Fig. 5- TYPICL J UNCTION CAPACITANCE PER ELEMENT
DATE : SEP.16.2002
PAGE . 2
Similar pages