Hittite HMC346LP3 Gaas mmic voltage-variable attenuator, dc - 14 ghz Datasheet

HMC346LP3 / 346LP3E
v05.1008
ATTENUATORS - SMT
5
GaAs MMIC VOLTAGE-VARIABLE
ATTENUATOR, DC - 14 GHz
Typical Applications
Features
The HMC346LP3 / HMC346LP3E is ideal for:
Wide Bandwidth: DC - 14 GHz
• Basestation Infrastructure
Low Phase Shift vs. Attenuation
• Fiber Optics & Broadband Telecom
30 dB Attenuation Range
• Microwave Radio & VSAT
Simplified Voltage Control
• Military Radios, Radar, & ECM
3 x 3 x 1 mm SMT Package
• Test Instrumentation
Functional Diagram
General Description
The HMC346LP3 & HMC346LP3E are pabsorptive Voltage Variable Attenuators (VVA) in low cost
leadless surface mount plastic packages operating
from DC - 14 GHz. It features an on-chip reference
attenuator for use with an external op-amp to provide
simple single voltage attenuation control, 0 to -3V.
The device is ideal in designs where an analog DC
control signal must control RF signal levels over a 30
dB amplitude range. This VVA is an excellent alternative to the HMC121C8.
Electrical Specifi cations, TA = +25° C, 50 ohm system
Parameter
Typical
Max
Units
1.7
2.8
2.2
3.3
dB
dB
Insertion Loss
DC - 10 GHz
DC - 14 GHz
Attenuation Range
DC - 10 GHz
DC - 14 GHz
27
22
30
27
dB
dB
DC - 14 GHz
5
Return Loss
10
dB
tRISE, tFALL (10/90% RF):
tON, tOFF (50% CTL to 10/90% RF):
2
8
ns
ns
Input Power for 0.25 dB Compression (0.5 - 8 GHz)
Min. Atten:
Atten. >2 dB:
+8
-4
dBm
dBm
Input Third Order Intercept (0.5 - 8 GHz)
(Two-tone Input Power = -8 dBm Each Tone)
Min. Atten:
Atten. >2 dB:
+25
+10
dBm
dBm
Switching Characteristics
5 - 96
Min
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC346LP3 / 346LP3E
v05.1008
GaAs MMIC VOLTAGE-VARIABLE
ATTENUATOR, DC - 14 GHz
-1
-10
-2
+25 C
-40 C
+85 C
-4
-20
-30
-40
0
2
4
6
8
10
12
14
16
0
2
4
FREQUENCY (GHz)
0
-5
-0.5
CONTROL VOLTAGE (Vdc)
RETURN LOSS (dB)
0
-10
-15
-20
MIN
5 dB
MAX
-30
10
12
14
16
V1
V2
-1
-1.5
-2
-2.5
-3
-35
0
2
4
6
8
10
12
14
0
16
5
10
15
20
25
30
RELATIVE ATTENUATION (dB)
FREQUENCY (GHz)
Relative Phase
Input IP3 vs. Attenuation*
180
30
5 dB
10 dB
15 dB
20 dB
25 dB
30 dB
max
150
120
25
INPUT IP3 (dBm)
RELATIVE PHASE (DEG)
8
Relative Attenuation vs.
Control Voltage @ 10 GHz
Return Loss vs. Attenuation
-25
6
FREQUENCY (GHz)
ATTENUATORS - SMT
0
ATTENUATION (dB)
INSERTION LOSS (dB)
0
-3
5
Relative Attenuation
Insertion Loss vs. Temperature
90
60
30
20
15
10
0 dB
3 dB
6 dB
10 dB
5
0
0
0
2
4
6
8
10
12
14
16
FREQUENCY (GHz)
0
2
4
6
8
10
12
14
16
FREQUENCY (GHz)
*Two-tone input power = -8 dBm each tone, 1 MHz spacing.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 97
HMC346LP3 / 346LP3E
v05.1008
GaAs MMIC VOLTAGE-VARIABLE
ATTENUATOR, DC - 14 GHz
Second Harmonic
vs. Attenuation, Pin = -8 dBm
70
80
60
70
SECOND HARMONIC (dBc)
INPUT IP2 (dBm)
Input IP2 vs. Attenuation*
50
40
30
0 dB
3 dB
6 dB
10 dB
20
10
60
50
40
0 dB
3 dB
6 dB
10 dB
30
20
0
2
4
6
8
10
12
14
16
0
2
4
FREQUENCY (GHz)
8
10
12
10
15
INPUT P1dB (dBm)
20
0 dB (REF)
6 dB
0
-5
16
10
5
0 dB (REF)
6 dB
0
-10
-5
0
2
4
6
8
10
12
14
16
FREQUENCY (GHz)
0
2
4
6
8
10
12
FREQUENCY (GHz)
*Two-tone input power = -8 dBm each tone, 1 MHz spacing.
5 - 98
14
1 dB Compression vs. Attenuation
15
5
6
FREQUENCY (GHz)
0.25 dB Compression vs. Attenuation
INPUT 0.25dB (dBm)
ATTENUATORS - SMT
5
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
14
16
HMC346LP3 / 346LP3E
v05.1008
GaAs MMIC VOLTAGE-VARIABLE
ATTENUATOR, DC - 14 GHz
RF Input Power
+18 dBm
Control Voltage Range
+1 to -5V
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
ESD Sensitivity (HBM)
Class 1A
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
ATTENUATORS - SMT
5
Absolute Maximum Ratings
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC346LP3
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC346LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
346
XXXX
[2]
346
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 99
HMC346LP3 / 346LP3E
v05.1008
GaAs MMIC VOLTAGE-VARIABLE
ATTENUATOR, DC - 14 GHz
ATTENUATORS - SMT
5
Pin Descriptions
Pin Number
Function
Description
1, 3, 7, 10, 12
GND
Package bottom has exposed metal paddle that must also be
connected to PCB RF ground.
2, 11
RF1
RF2
This pin is DC coupled and matched to 50 Ohm. Blocking
capacitors are required if the RF line potential is not equal to
0V.
4, 9, 13, 14, 15, 16
N/C
This pin should be connected to PCB RF ground.
5, 8
V2, V1
Control input (master).
6
I
Control input (slave).
Interface Schematic
Single-Line Control Driver
External op-amp control circuit maintains impedance match while attenuation is varied. Input control ranges from 0 Volts
(min. attenuation) to -3.0 Volts (max. attenuation.)
5 - 100
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC346LP3 / 346LP3E
v05.1008
GaAs MMIC VOLTAGE-VARIABLE
ATTENUATOR, DC - 14 GHz
5
ATTENUATORS - SMT
Evaluation PCB
List of Materials for Evaluation PCB 105709 [1]
Item
Description
J1 - J2
PCB Mount SMA RF Connector
J3 - J6
DC Pin
U1
HMC346LP3 / HMC346LP3E VVA
PCB [2]
105695 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
The circuit board used in the final application
should be generated with proper RF circuit design
techniques. Signal lines at the RF ports should be
50 ohm impedance and the package ground leads
and package bottom should be connected directly
to the PCB RF ground plane, similar to that shown
above. The evaluation circuit board shown above is
available from Hittite Microwave Corporation upon
request.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
5 - 101
Similar pages