TSC FRF1006G Isolation 10 amps. glass passivated fast recovery rectifier Datasheet

FRF1001G THRU FRF1007G
Isolation 10 AMPS. Glass Passivated Fast Recovery Rectifiers
Voltage Range
50 to 1000 Volts
Current
10 Amperes
ITO-220AB
Features
a
a
a
a
.185(4.7)
Low forward voltage drop
High current capability
High reliability
High surge current capability
.173(4.4)
.406(10.3)
.390(9.90)
.134(3.4)DIA
.113(3.0)DIA
.124(3.16)
. 11 8 ( 3 . 0 )
.112(2.85)
.100(2.55)
.272(6.9)
.248(6.3)
Mechanical Data
.606(15.5)
.583(14.8)
a Cases: ITO-220AB molded plastic
a Epoxy: UL 94V-0 rate flame retardant
a Terminals: Leads solderable per
MIL-STD-202, Method 208 guaranteed
a Polarity: As marked
a High temperature soldering guaranteed:
260/10 seconds 0.25”,(6.35mm) from
case.
a Mounting position: Any
aWeight: 2.24 grams
aMounting torque: 5 in – 1bs. max.
.161(4.1)
.146(3.7)
.110(2.8)
.098(2.5)
.055(1.4)
.030(0.76)
.035(0.9)
.020(0.50)
.020(0.5)
PIN 1
PIN 3
.543(13.8)
.512(13.2)
.043(1.1)
.106(2.7)
.106(2.7)
.094(2.4)
.094(2.4)
PIN 2
Positive CT
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Symbol FRF FRF FRF
Type Number
FRF FRF FRF FRF
1001G 1002G 1003G 1004G 1005G 1006G 1007G
Maximum Recurrent Peak Reverse Voltage
VRRM
Maximum RMS Voltage
VRMS
Maximum DC Blocking Voltage
VDC
Maximum Average Forward Rectified Current I(AV)
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method )
Maximum Instantaneous Forward Voltage
@ 5.0A
Maximum DC Reverse Current @ TC=25
at Rated DC Blocking Voltage @ TC=125
50
35
50
100
70
100
200
140
200
400
280
400
10
600
420
600
800 1000
560 700
800 1000
Units
V
V
V
A
IFSM
125
A
VF
1.3
V
IR
5.0
100
uA
uA
nS
/W
250
150
5.0
Operating and Storage Temperature Range TJ ,TSTG
-65 to +150
Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink size 2" x
3" x 0.25" Al-Plate
Maximum Reverse Recovery Time ( Note 1)
Typical Thermal Resistance (Note 2)
150
Trr
RθJC
- 408 -
RATINGS AND CHARACTERISTIC CURVES (FRF1001G THRU FRF1007G)
FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
10W
NONINDUCTIVE
50W
NONINDUCTIVE
trr
+0.5A
(-)
DUT
(+)
50Vdc
(approx)
(-)
PULSE
GENERATOR
(NOTE 2)
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
(+)
-1.0A
1cm
FIG.2- MAXIMUM FORWARD CURRENT DERATING
CURVE
10.0
8.0
6.0
4.0
0.2
0
50
100
150
o
PEAK FORWARD SURGE CURRENT. (A)
FIG.3- MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT PER LEG
150
125
INSTANTANEOUS REVERSE CURRENT. (µA)
1000
CASE TEMPERATURE. ( C)
8.3ms Single Half Sine Wave
JEDEC Method
100
Tj=125 0C
10
1.0
Tj=25 0C
0.1
100
0
20
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
75
FIG.6- TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER LEG
50
80
25
1
2
5
10
20
50
100
NUMBER OF CYCLES AT 60Hz
FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG
300
250
CAPACITANCE.(pF)
SET TIME BASE FOR
5/ 10ns/ cm
FIG.2- TYPICAL REVERSE CHARACTERISTICS
PER LEG
200
150
100
Tj=25 0C
f=1.0MHz
Vsig=50mVp-p
50
0.1
0.5
1.0
INSTANTANEOUS FORWARD CURRENT. (A)
AVERAGE FORWARD CURRENT. (A)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
12.0
0
-0.25A
40
20
10
4
2
1.0
.4
Tj=25oC
Pulse Width=300 s
1% Duty Cycle
.2
5
10
50
100
500
1000
.1
.8
.9
1.0
1.1
1.2
1.3
1.4
INSTANTANEOUS FORWARD VOLTAGE. (V)
REVERSE VOLTAGE. (V)
- 409 -
1.5
Similar pages