Kemet C1206C333K3GAC Surface mount ceramic chip capacitors - c0g dielectric Datasheet

Product Bulletin
Surface Mount Ceramic Chip Capacitors – C0G Dielectric
Outline Drawing
L
W
T
TIN PLATE
B
NICKEL PLATE
S
ELECTRODES
CONDUCTIVE METALLIZATION
Dimensions - Millimeters (Inches)
B - BANDWIDTH
S
SEPARATION
minimum
MOUNTING
TECHNIQUE
0.5 (.02) ± .05 (.002)
0.20 (.008) -.40 (.016)
0.3 (.012)
Solder Reflow
0.8 (.032) ± .15 (.006)
0.35 (.014) ± .15 (.006)
0.7 (.028)
1.25 (.049) ± .20 (.008)
0.50 (.02) ± .25 (.010)
0.75 (.030)
3.2 (.126) ± .20 (.008)
1.6 (.063) ± .20 (.008)
0.50 (.02) ± .25 (.010)
N/A
3.2 (.126) ± .20 (.008)
2.5 (.098) ± .20 (.008)
0.50 (.02) ± .25 (.010)
N/A
EIA SIZE
CODE
METRIC
SIZE CODE
0402
1005
1.0 (.04) ± .05 (.002)
0603
1608
1.6 (.063) ± .15 (.006)
0805
2012
2.0 (.079) ± .20 (.008)
1206
3216
1210
3225
L - LENGTH
W - WIDTH
Solder Wave +
or
Solder Reflow
See Capacitance Value Chart below for thickness dimension.
+ For extended values 1210 case sizes - solder reflow only.
Electrical Parameters
As detailed in the KEMET Surface Mount Catalog F3102 for C0G, with following specific requirements based on room
temperature (25°C) parameters:
• Operating Range: -55°C to +125°C, with no-bias capacitance shift limited to ± 30 PPM/°C over that range.
• Insulation Resistance (IR) measured after 2 minutes at rated voltage @ 25°C: Limit is 1000 megohm microfarads or
100GΩ, whichever is less.
• Capacitance and Dissipation Factor (DF) measured at the following conditions.
Capacitance - 1 kHz and 1 vrms if capacitance >1000 pF
1 MHz and 1 vrms if capacitance ≤ 1000 pF
DF Limit is 0.1%.
Soldering Process
These components are suitable for wave and reflow soldering. All parts incorporate the standard KEMET
barrier layer of pure nickel, with an overplate of pure tin to provide excellent solderability as well as resistance to leaching.
Marking
These chips will be supplied unmarked. However, marking is available as an extra cost option.
Qualification/Certification
AEC-Q200 Rev. C - Automotive
RoHS 6 - 100% tin termination
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
F9126 5/07
C 0805
C
103
K
3
G
A
C
End Metallization
C = Standard (Tin-plate
nickel barrier)
Style
C - Ceramic
Size Code
0402, 0603, 0805, 1206, 1210
Failure Rate Level
A = Not Applicable
Specification
C - Standard
Temperature Characteristic
Designated by Capacitance
Change Over Temperature Range
G = C0G (NP0) (±30 PPM/°C)
Capacitance Code, pF
First two digits represent significant figures.
Third digit specifies number of zeros. 100 pF = 101.
(Use “9” for 1.0 through 9.9 pF)
(Use “8” for 0.1 through .99 pF)
Voltage
3 = 25V
Capacitance Tolerance
F = ±1%
K = ±10%
G = ±2%
M = ±20%
J = ±5%
Capacitance Value
Capacitance
Values (pF)
KEMET Part
Number
Voltage
Capacitance
Tolerance
Thickness
mm
Qty
7” Reel
Qty
13” Reel
470
560
680
820
1000
C0402C471(1)3GAC
C0402C561(1)3GAC
C0402C681(1)3GAC
C0402C821(1)3GAC
C0402C102(1)3GAC
25
25
25
25
25
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
.50
.50
.50
.50
.50
±
±
±
±
±
.05
.05
.05
.05
.05
10,000
10,000
10,000
10,000
10,000
50,000
50,000
50,000
50,000
50,000
2200
2700
3300
3900
4700
5600
6800
8200
10,000
C0603C222(1)3GAC
C0603C272(1)3GAC
C0603C332(1)3GAC
C0603C392(1)3GAC
C0603C472(1)3GAC
C0603C562(1)3GAC
C0603C682(1)3GAC
C0603C822(1)3GAC
C0603C103(1)3GAC
25
25
25
25
25
25
25
25
25
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
.80
.80
.80
.80
.80
.80
.80
.80
.80
±
±
±
±
±
±
±
±
±
.10
.10
.10
.10
.10
.10
.10
.10
.10
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
4,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
4700
5600
6800
8200
10,000
18,000
22,000
33.000
C0805C472(1)3GAC
C0805C562(1)3GAC
C0805C682(1)3GAC
C0805C822(1)3GAC
C0805C103(1)3GAC
C0805C183(1)3GAC
C0805C223(1)3GAC
C0805C333(1)3GAC
25
25
25
25
25
25
25
25
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
.78 ± .10
.78 ± .10
.78 ± .10
.78 ± .10
.78 ± .10
.78 ± .10
.90 ± .10
1.25 ± .20
4,000
4,000
4,000
4,000
4,000
4,000
4,000
3,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
10,000
18,000
22,000
33,000
47,000
68,000
100,000
C1206C183(1)3GAC
C1206C223(1)3GAC
C1206C333(1)3GAC
C1206C473(1)3GAC
C1206C683(1)3GAC
C1206C104(1)3GAC
25
25
25
25
25
25
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
.78 ± .10
.78 ± .10
.78 ± .10
.90 ± .10
1.20 ± .15
1.60 ± .20
4,000
4,000
4,000
4,000
2,500
2,000
10,000
10,000
10,000
10,000
10,000
8,000
22,000
27,000
33,000
47,000
68,000
100,000
220,000
C1210C223(1)3GAC
C1210C273(1)3GAC
C1210C333(1)3GAC
C1210C473(1)3GAC
C1210C683(1)3GAC
C1210C104(1)3GAC
C1210C224(1)3GAC
25
25
25
25
25
25
25
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
F,G,J,K,M
.78 ± .10
.78 ± .10
.78 ± .10
.78 ± .10
.78 ± .10
1.00 ± .10
2.10 ± .20
4,000
4,000
4,000
4,000
4,000
2,500
2,000
10,000
10,000
10,000
10,000
10,000
10,000
8,000
(1) Insert capacitance tolerance as shown: F = ±1%; G = ±2%; J = ± 5%; K = ±10% or M = ±20%.
In general, the information in the KEMET Surface Mount catalog F3102 applies to these capacitors. The information in this bulletin supplements that in the catalog.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
Similar pages