Infineon LH1540AABTR 1 form a solid state relay Datasheet

LH1540AT/AAB/AABTR
1 Form A
Solid State Relay
FEATURES
• Current Limit Protection
• l/O Isolation, 5300 VRMS
• Typical RON 20 Ω, max 25 Ω
• Load Voltage 350 V
• Load Current 120 mA
• High Surge Capability
• Linear, AC/DC Operation
• Clean Bounce Free Switching
• Low Power Consumption
• High Reliability Monolithic Receptor
• SMD lead available on tape and reel
• Flammability; UL94,VØ
Package Dimensions in Inches (mm)
DIP
DC
S'
6
5
4
1
2
3
S
Pin One ID.
3
2
1
4
5
6
S'
.256 (6.50)
.248 (6.30)
.343 (8.70)
.335 (8.50)
.300 (7.62)
Typ.
.039
(1.00)
Min.
.150 (3.81)
.130 (3.30)
4° Typ.
AGENCY APPROVALS
• UL – File No. E52744
• BSI/BABT Cert. No. 7980
• FIMKO Approval
• CSA – Certification 093751
18° Typ.
.020 (.051) Min.
.035 (0.90)
.031 (0.80)
.022 (0.55)
.018 (0.45)
.100 (2.54) Typ.
.014 (.35)
.010 (.25)
.150 (3.81)
.110 (2.79)
.347 (8.82)
.300 (7.62)
SMD
.343 (8.71)
.335 (8.51)
APPLICATIONS
• General Telecom Switching
– On/off Hook Control
– Ring Delay
– Dial Pulse
– Ground Start
– Ground Fault Protection
• Instrumentation
• Industrial Controls
• See Application Note 56
Pin one I.D.
.256 (6.50)
.248 (6.30)
.050 (1.27) typ.
.039
(0.99)
min.
DESCRIPTION
The LH1540 is robust, ideal for telecom and ground
fault applications. It is a SPST normally open switch (1
Form A) that replaces electromechanical relays in many
applications. It is constructed using a GaAIAs LED for
actuation control and an integrated monolithic die for
the switch output. The die, fabricated in a high-voltage
dielectrically isolated technology, is comprised of a
photodiode array, switch control circuitry and MOSFET
switches. In addition, it employs current-limiting circuitry which meets FCC 68.302 and other regulatory
voltage surge requirements when overvoltage protection is provided.
S
.395 (10.03)
.375 (9.63)
.300 (7.62)
typ.
.052 (1.33)
.048 (1.22)
.150 (3.81)
.130 (3.30)
.0098 (.25)
.0040 (.10)
3° to 7°
18°
4°
.100 (2.54)
.040 (1.016)
.020 (0.508)
.315 (8.00)
min.
.012 (0.31)
.008 (0.20)
Part Identification
Part Number
Description
LH1540AT
6-pin DIP, Thru Hole
LH1540AAB
6-pin SMD
LH1540AABTR
6-pin SMD, Tape and Reel
 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA
www.infineon.com/opto • 1-888-Infineon (1-888-463-4636)
3–154
March 23, 2001-12
Absolute Maximum Ratings, TA=25°C
Recommended Operating Conditions
120
IFon =
5.0 to 20 mA
Load Current (mA)
100
80
60
40
IFon = 2.0 mA
IFon = 3.0 mA
IFon = 4.0 mA
20
0
–40
–20
0
20
40
60
80
Ambient Temperature (°C)
Stresses in excess of the absolute Maximum Ratings can cause permanent damage to the device. These are absolute stress ratings only. Functional operation of the device is not implied at these or any other
conditions in excess of those given in the operational sections of this document. Exposure to absolute Maximum Ratings for extended periods of
time can adversely affect reliability.
Ambient Temperature Range (TA) .................................... –40 to +85°C
Storage Temperature Range (Tstg) ................................. –40 to +150°C
Pin Soldering Temperature (t=10 s max) (TS) ............................. 260°C
Input/Output Isolation Voltage (VISO) .................................. 5300 VRMS
LED Continuous Forward Current (IF) .........................................50 mA
LED Reverse Voltage (IR≤10 µA) (VR)........................................... 8.0 V
DC or Peak AC Load Voltage (IL≤50 µA) (VL) .............................. 350 V
Continuous DC Load Current (IL)
Bidirectional Operation............................................................120 mA
Unidirectional Operation..........................................................250 mA
Peak Load Current (t=100 ms) (single shot) (IP) ................................ †
Output Power Dissipation (continuous) (PDISS)........................ 550 mW
† Refer to Current Limit Performance Application Note for a discussion on
relay operation during transient currents.
Electrical Characteristics, TA=25°C
Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the
result of engineering evaluations. Typical values are for information only and are not part of the testing requirements.
Parameter
Sym.
Min.
Typ.
Max.
Units
Test Conditions
LED Forward Current, Switch Turn-on
IFon
—
1.0
2.0
mA
IL=100 mA, t=10 ms
LED Forward Current, Switch Turn-off
IFoff
0.2
0.9
—
mA
VL±300 V
LED Forward Voltage
VF
1.15
1.26
1.45
V
IF=10 mA
RON
12
20
25
Ω
IF=5.0 mA, IL=50 mA
Input
Output
ON-resistance
ac/dc: Pin 4 (±) to 6 (±)
dc: Pin 4, 6 (+) to 5 (±)
IF=5.0 mA, IL=100 mA
3.0
5.0
6.25
OFF-resistance
ROFF
0.5
5000
—
GΩ
IF=0 mA, VL=±100 V
Current Limit
ac/dc: Pin 4 (±) to 6 (±)
ILMT
175
210
250
mA
IF=5.0 mA, t=5.0 ms
VL=±6.0 V
—
—
—
—
0.32
200
nA
IF=0 mA, VL=±100 V
—
1.0
350
µA
IF=0 mA, VL=±350 V
55
—
pF
IF=0 mA, VL=1.0 V
dc: Pin 4, 6 (+) to 5 (±)
Off-state Leakage Current
—
IF=5.0 mA, t=5.0 ms
VL=±4.0 V
Output Capacitance
Pin 4 to 6
—
—
—
10
—
Switch Offset
—
—
0.15
—
V
IF=5.0 mA
Input/Output Capacitance
CISO
—
0.8
—
pF
VISO=1.0 V
Turn-on Time
ton
—
1.2
2.0
ms
IF=5.0 mA, IL=50 mA
Turn-off Time
toff
—
0.5
2.0
ms
IF=5.0 mA, IL=50 mA
IF=0 mA, VL=50 V
Transfer
 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA
www.infineon.com/opto • 1-888-Infineon (1-888-463-4636)
LH1540AT/AAB/AABTR
3–155
March 23, 2001-12
Typical Performance Characteristics
Figure 4. Current Limit vs. Temperature
Figure 1. LED Voltage vs. Temperature
40
1.5
IF=50 mA
IF=20 mA
1.4
1.3
1.2
IF=1.0 mA
1.1 IF=2.0 mA
1.0
–40
IF=5.0 mA
IF=10 mA
–20
0
20
40
60
CHANGE IN CURRENT LIMIT (%)
NORMALIZED TO 25°C
LED FORWARD VOLTAGE (V)
1.6
IF=5.0 mA
t=5 ms
VL=SEE ELEC. CHAR.
30
20
10
0
–10
–20
–30
–40
–40
80
Figure 2. LED Dropout Voltage vs. Temperature
20
40
60
80
Figure 5. ON-Resistance vs. Temperature
1.20
50
CHANGE IN ON-RESISTANCE (%)
NORMALIZED TO 25°C
LED FORWARD VOLTAGE (V)
0
AMBIENT TEMPERATURE (°C)
AMBIENT TEMPERATURE (°C)
IL=100 mA
1.15
TYP.
1.10
MIN.
1.05
1.00
0.95
–40
–20
0
20
40
60
40
IL=50 mA
30
20
10
0
–10
–20
–30
–40
–40
80
100
IL=100 mA
80
60
40
20
0
–20
–40
–20
0
20
40
60
0
20
40
60
80
Figure 6. Variation in ON-Resistance vs. LED Current
ac/dc ON-RESISTANCE VARIATION (%)
NORMALIZED TC DATA SHEET RON
SPECIFICATION @ IF=5.0 mA
Figure 3. LED Current for Switch Turn-on vs. Temperature
–60
–40
–20
AMBIENT TEMPERATURE (°C)
AMBIENT TEMPERATURE (°C)
LED FORWARD CURRENT FOR SWITCH
TURN-ON (%) NORMALIZED TO 25°C
–20
1.5
IL=50 mA
1.0
0.5
0
–0.5
0
80
4
8
12
16
20
LED FORWARD CURRENT (mA)
AMBIENT TEMPERATURE (°C)
 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA
www.infineon.com/opto • 1-888-Infineon (1-888-463-4636)
LH1540AT/AAB/AABTR
3–156
March 23, 2001-12
Figure 10. Leakage Current vs. Applied Voltage
OFF-STATE LEAKAGE CURRENT (pA)
Figure 7. Switch Capacitance vs. Applied Voltage
80
IF=0
TA=25°C
f=1.0 MHz
CAPACITANCE (pF)
70
60
50
40
30
20
10
0
0
20
40
60
80
100
90
IF=0
TA=25°C
80
70
60
50
40
30
20
10
0
100
0
50
100
APPLIED VOLTAGE (V)
INSERTION LOSS (dB)
0.30
RL=600 Ω
0.20
0.15
0.10
0.05
0
102
103
104
400
2.5
85°C
2.0
1.5
70°C
1.0
0.5
50°C
0
50
100
150
200
250
300
350
400
LOAD VOLTAGE (V)
VP=10 V
RL=50 Ω
80
60
40
20
0
104
105
106
107
CHANGE IN BREAKDOWN VOLTAGE (%)
NORMALIZED TO 25°C
Figure 12. Switch Breakdown Voltage vs. Temperature
100
ISOLATION (dB)
350
0
105
Figure 9. Output Isolation
103
250 300
3.0
FREQUENCY (Hz)
102
200
Figure 11. Leakage Current vs. Applied Voltage at
Elevated Temperatures
OFF-STATE LEAKAGE CURRENT (nA)
Figure 8. Insertion Loss vs. Frequency
0.25
150
LOAD VOLTAGE (V)
8
6
4
2
0
–2
–4
–6
–8
–40
–20
0
20
40
60
80
AMBIENT TEMPERATURE (°C)
FREQUENCY (Hz)
 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA
www.infineon.com/opto • 1-888-Infineon (1-888-463-4636)
LH1540AT/AAB/AABTR
3–157
March 23, 2001-12
Figure 13. Switch Offset Voltage vs. Temperature
Figure 16. Turn-off Time vs. Temperature
CHANGE IN TURN-OFF TIME (%)
NORMALIZED TO 25°C
SWITCH OFFSET VOLTAGE (µV)
3.5
IF=5.0 mA
3.0
2.5
2.0
1.5
1.0
0.5
0
20
30
40
50
60
70
80
90
160
140
120
IF=5.0 mA
IL=50 mA
100
80
60
40
20
0
–20
–40
–60
–80
–40
–20
Figure 14. Switch Offset Voltage vs. LED Current
40
60
80
Figure 17. Turn-on Time vs. LED Current
0.6
10
0.5
8
TURN-ON TIME (ms)
SWITCH OFFSET VOLTAGE (µV)
20
AMBIENT TEMPERATURE (°C)
AMBIENT TEMPERATURE (°C)
0.4
0.3
0.2
IL=50 mA
–40°C
6
25°C
85°C
4
–40°C
25°C
85°C
2
0.1
0
0
0
5
10
15
20
0
25
10
LED FORWARD CURRENT (mA)
20
30
40
50
LED FORWARD CURRENT (mA)
Figure 15. Turn-on Time vs. Temperature
Figure 18. Turn-off Time vs. LED Current
60
50
1.4
40
1.2
IL=50 mA
TURN-ON TIME (ms)
CHANGE IN TURN-ON TIME (%)
NORMALIZED TO 25°C
0
30
20
10
0
–10
–40°C
1.0
0.8
25°C
0.6
–20
–40
–40
0.4
IF=5.0 mA
IL=50 mA
–30
–20
0
20
40
60
85°C
0.2
80
0
AMBIENT TEMPERATURE (°C)
10
20
30
40
50
LED FORWARD CURRENT (mA)
 2001 Infineon Technologies Corp. • Optoelectronics Division • San Jose, CA
www.infineon.com/opto • 1-888-Infineon (1-888-463-4636)
LH1540AT/AAB/AABTR
3–158
March 23, 2001-12
Similar pages