Hittite HMC494LP3 Smt gaas hbt mmic divide-by-8, dc - 18 ghz Datasheet

HMC494LP3
v01.0604
MICROWAVE CORPORATION
SMT GaAs HBT MMIC
DIVIDE-BY-8, DC - 18 GHz
10
Typical Applications
Features
Prescaler for DC to 18 GHz PLL Applications:
Ultra Low SSB Phase Noise: -150 dBc/Hz
• Point-to-Point / Multi-Point Radios
Very Wide Bandwidth
• VSAT Radios
Output Power: -4 dBm
• Fiber Optic
Single DC Supply: +5V
• Test Equipment
3 x 3 x 1 mm QFN Package
FREQ. DIVIDER & DETECTORS - SMT
• Military
Functional Diagram
General Description
The HMC494LP3 is a low noise Divide-by-8
Static Divider utilizing InGaP GaAs HBT technology packaged in a leadless 3x3 mm QFN surface
mount plastic package. This device operates from
DC (with a square wave input) to 18 GHz input
frequency from a single +5.0V DC supply. The
low additive SSB phase noise of -150 dBc/Hz at
100 kHz offset helps the user maintain excellent
system noise performance.
Electrical Specifications, TA = +25° C, 50 Ohm System, Vcc= +5V
Parameter
Conditions
Maximum Input Frequency
Minimum Input Frequency
Input Power Range
Output Power
Reverse Leakage
SSB Phase Noise (100 kHz offset)
Output Transition Time
Min.
Typ.
18
19
Sine Wave Input. [1]
Max.
GHz
0.2
0.5
GHz
Fin = 2 to 12 GHz
-15
-20
+10
dBm
Fin = 12 to 16 GHz
-15
-20
+3
dBm
Fin = 16 to 18 GHz
-10
-15
0
dBm
Fin = 0.5 to 18 GHz
-7
-4
dBm
Both RF Outputs Terminated
55
dB
Pin = 0 dBm, Fin = 6 GHz
-150
dBc/Hz
Pin = 0 dBm, Fout = 882 MHz
100
ps
103
mA
Supply Current (Icc1 + Icc2)
1. Divider will operate down to DC for square-wave input signal.
10 - 130
Units
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
HMC494LP3
v01.0604
MICROWAVE CORPORATION
SMT GaAs HBT MMIC
DIVIDE-BY-8, DC - 18 GHz
20
10
10
0
Recommended
Operating Window
-10
-20
0
Min Pin +25C
Max Pin +25C
Min Pin +85C
Max Pin +85C
Min Pin -40C
Max Pin -40C
-10
-20
-30
-30
0
2
4
6
8
10
12
14
16
18
20
0
2
4
6
INPUT FREQUENCY (GHz)
0
-20
SSB PHASE NOISE (dBc/Hz)
OUTPUT POWER (dBm)
0
-2
-3
-4
-5
-6
-7
+25C
+85C
-40C
-8
-9
-10
2
4
6
8
10
12
14
10
12
14
16
18
20
SSB Phase Noise Performance,
Pin= 0 dBm, T= 25 °C
-1
0
8
INPUT FREQUENCY (GHz)
Output Power vs. Temperature
16
18
-40
-60
-80
-100
-120
-140
-160
2
10
20
3
4
10
INPUT FREQUENCY (GHz)
5
10
6
10
7
10
10
OFFSET FREQUENCY (Hz)
Output Harmonic Content,
Pin= 0 dBm, T= 25 °C
Reverse Leakage, Pin= 0 dBm, T= 25 °C
0
0
Both Output Ports Terminated
-10
-10
One Output Port Terminated
-20
OUTPUT LEVEL (dBm)
OUTPUT LEVEL (dBm)
10
Pfeedthru
2nd Harmonic
3rd Harmonic
-30
-40
-20
FREQ. DIVIDERS & DETECTORS - SMT
20
INPUT POWER (dBm)
INPUT POWER (dBm)
MMIC
SUB-HARMONICALLY
PUMPED
MIXER
- 25 GHz
InputGaAs
Sensitivity
Window,
T= 25 °C
Input
Sensitivity
Window17
vs. Temperature
-30
-40
-50
-60
-70
-50
-80
0
2
4
6
8
10
12
14
INPUT FREQUENCY (GHz)
16
18
20
0
2
4
6
8
10
12
14
16
18
20
INPUT FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
10 - 131
MICROWAVE CORPORATION
HMC494LP3
v01.0604
SMT GaAs HBT MMIC
DIVIDE-BY-8, DC - 18 GHz
Output Voltage Waveform,
Pin= 0 dBm, Fout= 882 MHz, T= 25 °C
500
Absolute Maximum Ratings
RF Input (Vcc = +5V)
+13 dBm
300
Supply Voltage (Vcc1, Vcc2)
+5.5V
200
Channel Temperature (Tc)
135 °C
Continuous Pdiss (T = 85 °C)
(derate 11.9 mW/° C above 85 °C)
593 mW
Thermal Resistance (RTH)
(junction to ground paddle)
84 °C/W
-400
Storage Temperature
-65 to +150 °C
-500
22.7 22.9 23.1 23.3 23.5 23.7 23.9 24.1 24.3 24.5 24.7
Operating Temperature
-40 to +85 °C
10
AMPLITUDE (mV)
400
100
0
-100
-200
FREQ. DIVIDER & DETECTORS - SMT
-300
TIME (nS)
Outline Drawing
Typical Supply Current vs. Vcc
Vcc1, Vcc2 (V)
Icc (mA)
4.75
90
5.0
103
5.25
115
Note: Divider will operate over full voltage range shown above
NOTES:
1. MATERIAL PACKAGE BODY: LOW STRESS INJECTION MOLDED
PLASTIC SILICA AND SILICON IMPREGNATED.
2. LEAD AND GROUND PADDLE MATERIAL: COPPER ALLOY
3. LEAD AND GROUND PADDLE PLATING: Sn/Pb SOLDER
4. DIMENSIONS ARE IN INCHES [MILLIMETERS].
5. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
6. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
7. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
8. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED
TO PCB RF GROUND.
9. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB
LAND PATTERN.
10 - 132
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
MICROWAVE CORPORATION
HMC494LP3
v01.0604
SMT GaAs HBT MMIC
DIVIDE-BY-8, DC - 18 GHz
Pin Description
Pin Number
Function
Description
1, 4-9, 12, 13, 16
N/C
No connection.
Interface Schematic
2
IN
RF Input must be DC blocked.
3
IN
RF Input 180° out of phase with pin 2 for differential operation.
AC ground for single ended operation.
10
OUT
Divided Output.
11
OUT
Divided output 180° out of phase with pin 10.
14, 15
Vcc1, Vcc2
Supply voltage 5V ± 0.25V. Connect both pins to +5V supply.
GND
Ground: Backside of package has exposed metal ground slug which
must be connected to RF/DC ground.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
FREQ. DIVIDERS & DETECTORS - SMT
10
10 - 133
MICROWAVE CORPORATION
v01.0604
HMC494LP3
SMT GaAs HBT MMIC
DIVIDE-BY-8, DC - 18 GHz
Evaluation PCB
FREQ. DIVIDER & DETECTORS - SMT
10
List of Materials
Item
Description
J1 - J3
PC Mount SMA RF Connector
J4, J5
DC Pin
C2 - C5
100 pF Capacitor, 0402 Pkg.
C6
1000 pF Capacitor, 0603 Pkg.
C1
2.2 uF Tantalum Capacitor
U1
HMC492LP3 Divide-by-2
PCB*
107197 Eval Board
The circuit board used in the final application should use
RF circuit design techniques. Signal lines should have
50 ohm impedance while the package ground leads
and backside ground slug should be connected directly
to the ground plane similar to that shown. A sufficient
number of via holes should be used to connect the top
and bottom ground planes. The evaluation circuit board
shown is available from Hittite upon request. This evaluation board is designed for single ended input testing. J2
and J3 provide differential output signals.
* Circuit Board Material: Rogers 4350
10 - 134
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
MICROWAVE CORPORATION
v01.0604
HMC494LP3
SMT GaAs HBT MMIC
DIVIDE-BY-8, DC - 18 GHz
Application Circuit
FREQ. DIVIDERS & DETECTORS - SMT
10
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order Online at www.hittite.com
10 - 135
Similar pages