Microchip LAN9312-NZW High performance two port 10/100 managed ethernet switch with 32-bit non-pci cpu interface Datasheet

LAN9312
High Performance
Two Port 10/100 Managed Ethernet Switch with 32-Bit
Non-PCI CPU Interface
PRODUCT FEATURES
Datasheet
Highlights





—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
High performance and full featured 2 port switch with
VLAN, QoS packet prioritization, Rate Limiting, IGMP
monitoring and management functions
Easily interfaces to most 32-bit embedded CPU’s
Unique Virtual PHY feature simplifies software
development by mimicking the multiple switch ports
as a single port MAC/PHY
Integrated IEEE 1588 Hardware Time Stamp Unit
Target Applications







Cable, satellite, and IP set-top boxes
Digital televisions
Digital video recorders
VoIP/Video phone systems
Home gateways
Test/Measurement equipment
Industrial automation systems


Ethernet Switch Fabric
— 32K buffer RAM
— 1K entry forwarding table
— Port based IEEE 802.1Q VLAN support (16 groups)
– Programmable IEEE 802.1Q tag insertion/removal
— IEEE 802.1d spanning tree protocol support
— QoS/CoS Packet prioritization
– 4 dynamic QoS queues per port
– Input priority determined by VLAN tag, DA lookup,
TOS, DIFFSERV or port default value
– Programmable class of service map based on input
priority
– Remapping of 802.1Q priority field on per port basis
– Programmable rate limiting at the ingress/egress
ports with random early discard, per port / priority
— IGMP v1/v2/v3 monitoring for Multicast packet filtering
— Programmable filter by MAC address

Switch Management
2 internal 10/100 PHYs with HP Auto-MDIX support
Fully compliant with IEEE 802.3 standards
10BASE-T and 100BASE-TX support
Full and half duplex support
Full duplex flow control
Backpressure (forced collision) half duplex flow control
Automatic flow control based on programmable levels
Automatic 32-bit CRC generation and checking
Automatic payload padding
2K Jumbo packet support
Programmable interframe gap, flow control pause value
Full transmit/receive statistics
Auto-negotiation
Automatic MDI/MDI-X
Loop-back mode
High-performance host bus interface
—
—
—
—
—
—
—
—
Key Benefits

Ports
Provides in-band network communication path
Access to management registers
Simple, SRAM-like interface
32-bit data bus
Big, little, and mixed endian support
Large TX and RX FIFO’s for high latency applications
Programmable water marks and threshold levels
Host interrupt support
IEEE 1588 Hardware Time Stamp Unit
— Global 64-bit tunable clock
— Master or slave mode per port
— Time stamp on TX or RX of Sync and Delay_req
packets per port, Timestamp on GPIO
— 64-bit timer comparator event generation (GPIO or IRQ)

Comprehensive Power Management Features
—
—
—
—

Wake on LAN
Wake on link status change (energy detect)
Magic packet wakeup
Wakeup indicator event signal
Other Features
— General Purpose Timer
— Serial EEPROM interface (I2C master or MicrowireTM
master) for non-managed configuration
— Programmable GPIOs/LEDs


Single 3.3V power supply
Available in Commercial Temp. Range
— Port mirroring/monitoring/sniffing: ingress and/or egress
traffic on any ports or port pairs
— Fully compliant statistics (MIB) gathering counters
— Control registers configurable on-the-fly
SMSC LAN9312
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Order Numbers:
LAN9312-NU For 128-Pin, VTQFP Lead-Free RoHS Compliant Package (0 TO 70°C Temp Range)
LAN9312-NZW For 128-Pin, XVTQFP Lead-Free RoHS Compliant Package (0 TO 70°C Temp Range)
LAN9312-NU-TR For 128-Pin, VTQFP Lead-Free RoHS Compliant Package (0 TO 70°C Temp Range)
LAN9312-NZW-TR For 128-Pin, XVTQFP Lead-Free RoHS Compliant Package (0 TO 70°C Temp Range)
TR indicates tape & reel option.
This product meets the halogen maximum concentration values per IEC61249-2-21
For RoHS compliance and environmental information, please visit www.smsc.com/rohs
Copyright © 2013 SMSC or its subsidiaries. All rights reserved.
Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for
construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC
reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications
before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent
rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated
version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors
known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not
designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property
damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of
this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered
trademark of Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders.
The Microchip name and logo, and the Microchip logo are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE
OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL
DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT;
TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD
TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Revision 2.0 (02-14-13)
2
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table of Contents
Chapter 1 Preface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.1
1.2
1.3
General Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Buffer Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Register Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Chapter 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.1
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.1 System Clocks/Reset/PME Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.2 System Interrupt Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3 Switch Fabric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.4 Ethernet PHYs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.5 Host Bus Interface (HBI). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.6 Host MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.7 EEPROM Controller/Loader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.8 1588 Time Stamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.9 GPIO/LED Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3
System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
21
22
22
23
23
23
24
24
24
25
25
Chapter 3 Pin Description and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.1
Pin Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.1 128-VTQFP Pin Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1.2 128-XVTQFP Pin Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
26
27
28
Chapter 4 Clocking, Resets, and Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.1
Clocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.2
Resets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.2.1 Chip-Level Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.2.1.1
4.2.1.2
Power-On Reset (POR) .................................................................................................................................................................................. 38
nRST Pin Reset .............................................................................................................................................................................................. 38
4.2.2
Multi-Module Resets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.2.2.1
4.2.2.2
Digital Reset (DIGITAL_RST) ......................................................................................................................................................................... 38
Soft Reset (SRST) .......................................................................................................................................................................................... 39
4.2.3
Single-Module Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.2.3.1
4.2.3.2
4.2.3.3
Port 2 PHY Reset............................................................................................................................................................................................ 39
Port 1 PHY Reset............................................................................................................................................................................................ 39
Virtual PHY Reset ........................................................................................................................................................................................... 40
4.2.4
Configuration Straps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.2.4.1
4.2.4.2
Soft-Straps ...................................................................................................................................................................................................... 40
Hard-Straps..................................................................................................................................................................................................... 45
4.3
Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.3.1 Port 1 & 2 PHY Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.3.2 Host MAC Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Chapter 5 System Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.1
Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2
Interrupt Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.1 1588 Time Stamp Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.2 Switch Fabric Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.3 Ethernet PHY Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.4 GPIO Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.5 Host MAC Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMSC LAN9312
3
DATASHEET
49
49
51
51
52
52
52
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
5.2.6
5.2.7
5.2.8
5.2.9
Power Management Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Purpose Timer Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Ready Interrupt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
53
54
54
Chapter 6 Switch Fabric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.1
Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2
Switch Fabric CSRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.1 Switch Fabric CSR Writes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.2 Switch Fabric CSR Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.3 Flow Control Enable Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3
10/100 Ethernet MACs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.1 Receive MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.1.1
55
55
56
57
58
60
60
Receive Counters ........................................................................................................................................................................................... 61
6.3.2
Transmit MAC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.3.2.1
Transmit Counters .......................................................................................................................................................................................... 62
6.4.1.1
6.4.1.2
6.4.1.3
6.4.1.4
6.4.1.5
6.4.1.6
6.4.1.7
Learning/Aging/Migration ................................................................................................................................................................................ 64
Static Entries................................................................................................................................................................................................... 64
Multicast Pruning ............................................................................................................................................................................................ 64
Address Filtering ............................................................................................................................................................................................. 64
Spanning Tree Port State Override................................................................................................................................................................. 64
MAC Destination Address Lookup Priority...................................................................................................................................................... 64
Host Access .................................................................................................................................................................................................... 64
6.4
Switch Engine (SWE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.4.1 MAC Address Lookup Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.4.2
6.4.3
Forwarding Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Transmit Priority Queue Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.4.3.1
6.4.3.2
6.4.3.3
6.4.3.4
Port Default Priority......................................................................................................................................................................................... 69
IP Precedence Based Priority ......................................................................................................................................................................... 69
DIFFSERV Based Priority............................................................................................................................................................................... 69
VLAN Priority .................................................................................................................................................................................................. 69
6.4.4
6.4.5
6.4.6
6.4.6.1
VLAN Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Spanning Tree Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Ingress Flow Metering and Coloring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Ingress Flow Calculation................................................................................................................................................................................. 72
6.4.7
6.4.8
6.4.9
6.4.10
Broadcast Storm Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IPv4 IGMP Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Port Mirroring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Host CPU Port Special Tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
74
74
75
75
6.4.10.1
6.4.10.2
Packets from the Host CPU ............................................................................................................................................................................ 75
Packets to the Host CPU ................................................................................................................................................................................ 76
6.5.1.1
Buffer Limits and Flow Control Levels ............................................................................................................................................................ 77
6.4.11 Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
6.5
Buffer Manager (BM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
6.5.1 Packet Buffer Allocation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
6.5.2 Random Early Discard (RED). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5.3 Transmit Queues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5.4 Transmit Priority Queue Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5.5 Egress Rate Limiting (Leaky Bucket) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5.6 Adding, Removing, and Changing VLAN Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5.7 Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6
Switch Fabric Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
77
77
78
78
79
81
81
Chapter 7 Ethernet PHYs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
7.1
Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1.1 PHY Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2
Port 1 & 2 PHYs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.1 100BASE-TX Transmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.1.1
7.2.1.2
7.2.1.3
82
82
83
84
MII MAC Interface ........................................................................................................................................................................................... 84
4B/5B Encoder................................................................................................................................................................................................ 84
Scrambler and PISO ....................................................................................................................................................................................... 86
Revision 2.0 (02-14-13)
4
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
7.2.1.4
7.2.1.5
7.2.1.6
NRZI and MLT-3 Encoding ............................................................................................................................................................................. 86
100M Transmit Driver ..................................................................................................................................................................................... 86
100M Phase Lock Loop (PLL) ........................................................................................................................................................................ 86
7.2.2
100BASE-TX Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
7.2.2.1
7.2.2.2
7.2.2.3
7.2.2.4
7.2.2.5
7.2.2.6
7.2.2.7
A/D Converter ................................................................................................................................................................................................. 87
DSP: Equalizer, BLW Correction and Clock/Data Recovery .......................................................................................................................... 87
NRZI and MLT-3 Decoding ............................................................................................................................................................................. 88
Descrambler and SIPO ................................................................................................................................................................................... 88
5B/4B Decoding .............................................................................................................................................................................................. 88
Receiver Errors ............................................................................................................................................................................................... 88
MII MAC Interface ........................................................................................................................................................................................... 88
7.2.3
10BASE-T Transmit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
7.2.3.1
7.2.3.2
MII MAC Interface ........................................................................................................................................................................................... 89
10M TX Driver and PLL .................................................................................................................................................................................. 89
7.2.4
10BASE-T Receive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
7.2.4.1
7.2.4.2
7.2.4.3
7.2.4.4
Filter and Squelch ........................................................................................................................................................................................... 89
10M RX and PLL............................................................................................................................................................................................. 89
MII MAC Interface ........................................................................................................................................................................................... 90
Jabber Detection............................................................................................................................................................................................. 90
7.2.5
PHY Auto-negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
7.2.5.1
7.2.5.2
7.2.5.3
7.2.5.4
7.2.5.5
PHY Pause Flow Control ................................................................................................................................................................................ 92
Parallel Detection............................................................................................................................................................................................ 92
Restarting Auto-Negotiation............................................................................................................................................................................ 92
Disabling Auto-Negotiation ............................................................................................................................................................................. 92
Half Vs. Full-Duplex ........................................................................................................................................................................................ 93
7.2.6
7.2.7
7.2.8
7.2.8.1
HP Auto-MDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
MII MAC Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
PHY Management Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
PHY Interrupts ................................................................................................................................................................................................ 94
7.2.9
PHY Power-Down Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
7.2.9.1
7.2.9.2
PHY General Power-Down ............................................................................................................................................................................. 95
PHY Energy Detect Power-Down ................................................................................................................................................................... 95
7.2.10.1
7.2.10.2
7.2.10.3
PHY Software Reset via RESET_CTL............................................................................................................................................................ 95
PHY Software Reset via PHY_BASIC_CTRL_x ............................................................................................................................................. 96
PHY Power-Down Reset................................................................................................................................................................................. 96
7.3.1.1
7.3.1.2
7.3.1.3
Parallel Detection............................................................................................................................................................................................ 97
Disabling Auto-Negotiation ............................................................................................................................................................................. 97
Virtual PHY Pause Flow Control ..................................................................................................................................................................... 98
7.2.10 PHY Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
7.2.11 LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.12 Required Ethernet Magnetics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3
Virtual PHY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3.1 Virtual PHY Auto-Negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
96
96
96
96
7.3.2
Virtual PHY Resets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
7.3.2.1
7.3.2.2
7.3.2.3
Virtual PHY Software Reset via RESET_CTL ................................................................................................................................................ 98
Virtual PHY Software Reset via VPHY_BASIC_CTRL ................................................................................................................................... 98
Virtual PHY Software Reset via PMT_CTRL .................................................................................................................................................. 98
Chapter 8 Host Bus Interface (HBI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
8.1
8.2
8.3
8.4
8.4.1
Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Host Memory Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Host Endianess. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Host Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Special Situations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
8.4.1.1
8.4.1.2
Reset Ending During a Read Cycle .............................................................................................................................................................. 101
Writes Following a Reset .............................................................................................................................................................................. 101
8.4.2 Special Restrictions on Back-to Back Write-Read Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4.3 Special Restrictions on Back-to-Back Read Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4.4 PIO Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4.5 PIO Burst Reads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4.6 RX Data FIFO Direct PIO Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4.7 RX Data FIFO Direct PIO Burst Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4.8 PIO Writes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4.9 TX Data FIFO Direct PIO Writes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.5
HBI Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMSC LAN9312
5
DATASHEET
101
105
106
107
108
109
110
111
111
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 9 Host MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
9.1
9.2
9.2.1
9.2.2
9.3
9.4
9.4.1
9.4.2
9.4.3
9.4.4
9.5
9.5.1
9.6
9.7
9.7.1
9.7.2
9.7.3
9.8
9.8.1
9.8.2
9.8.2.1
9.8.2.2
Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Full-Duplex Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Half-Duplex Flow Control (Backpressure) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Virtual Local Area Network (VLAN) Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address Filtering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Perfect Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hash Only Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hash Perfect Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inverse Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wake-up Frame Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Magic Packet Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Host MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIFOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TX/RX FIFOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MIL FIFOs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FIFO Memory Allocation Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TX Data Path Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TX Buffer Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TX Command Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
112
113
113
113
113
114
115
115
115
116
116
118
119
120
120
120
121
122
124
124
TX Command ‘A’........................................................................................................................................................................................... 125
TX Command ‘B’........................................................................................................................................................................................... 126
9.8.3
TX Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
9.8.3.1
9.8.3.2
TX Buffer Fragmentation Rules .................................................................................................................................................................... 126
Calculating Worst-Case TX MIL FIFO Usage ............................................................................................................................................... 127
9.8.4
9.8.5
9.8.6
TX Status Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Calculating Actual TX Data FIFO Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Transmit Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
9.8.6.1
9.8.6.2
TX Example 1 ............................................................................................................................................................................................... 128
TX Example 2 ............................................................................................................................................................................................... 130
9.9.1.1
9.9.1.2
Receive Data FIFO Fast Forward ................................................................................................................................................................. 134
Force Receiver Discard (Receiver Dump) .................................................................................................................................................... 134
9.8.7 Transmitter Errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.8.8 Stopping and Starting the Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9
RX Data Path Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9.1 RX Slave PIO Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9.2
9.9.3
9.9.4
9.9.5
RX Packet Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RX Status Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stopping and Starting the Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiver Errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
131
131
132
132
134
135
136
136
Chapter 10 Serial Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
10.1 Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.2 I2C/Microwire Master EEPROM Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.2.1 EEPROM Controller Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.2.2 I2C EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
137
137
138
139
10.2.2.1
10.2.2.2
10.2.2.3
10.2.2.4
10.2.2.5
I2C Protocol Overview .................................................................................................................................................................................. 140
I2C EEPROM Device Addressing................................................................................................................................................................. 141
I2C EEPROM Byte Read .............................................................................................................................................................................. 141
I2C EEPROM Sequential Byte Reads .......................................................................................................................................................... 142
I2C EEPROM Byte Writes ............................................................................................................................................................................ 143
10.2.3.1
10.2.3.2
10.2.3.3
10.2.3.4
10.2.3.5
10.2.3.6
10.2.3.7
Microwire Master Commands ....................................................................................................................................................................... 144
ERASE (Erase Location) .............................................................................................................................................................................. 145
ERAL (Erase All)........................................................................................................................................................................................... 146
EWDS (Erase/Write Disable) ........................................................................................................................................................................ 146
EWEN (Erase/Write Enable)......................................................................................................................................................................... 147
READ (Read Location) ................................................................................................................................................................................. 147
WRITE (Write Location) ................................................................................................................................................................................ 148
10.2.3 Microwire EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Revision 2.0 (02-14-13)
6
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
10.2.3.8
WRAL (Write All)........................................................................................................................................................................................... 148
10.2.4.1
10.2.4.2
10.2.4.3
EEPROM Loader Operation ......................................................................................................................................................................... 149
EEPROM Valid Flag ..................................................................................................................................................................................... 151
MAC Address................................................................................................................................................................................................ 151
10.2.4.4
Soft-Straps .................................................................................................................................................................................................... 151
10.2.4.5
10.2.4.6
10.2.4.7
Register Data ................................................................................................................................................................................................ 152
EEPROM Loader Finished Wait-State.......................................................................................................................................................... 153
Reset Sequence and EEPROM Loader........................................................................................................................................................ 153
10.2.4 EEPROM Loader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
10.2.4.3.1Host MAC Address Reload ......................................................................................................151
10.2.4.4.1PHY Registers Synchronization ...............................................................................................151
10.2.4.4.2Virtual PHY Registers Synchronization....................................................................................152
10.2.4.4.3LED and Manual Flow Control Register Synchronization ........................................................152
Chapter 11 IEEE 1588 Hardware Time Stamp Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
11.1 Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1.1 IEEE 1588 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.1.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2 IEEE 1588 Time Stamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2.1 Capture Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.2.2 PTP Message Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.3 IEEE 1588 Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4 IEEE 1588 Clock/Events. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.5 IEEE 1588 GPIOs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.6 IEEE 1588 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
154
154
155
156
157
158
159
159
160
160
Chapter 12 General Purpose Timer & Free-Running Clock. . . . . . . . . . . . . . . . . . . . . . . . 161
12.1
12.2
General Purpose Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Free-Running Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Chapter 13 GPIO/LED Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
13.1 Functional Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
13.2 GPIO Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
13.2.1 GPIO IEEE 1588 Timestamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
13.2.1.1
13.2.1.2
IEEE 1588 GPIO Inputs ................................................................................................................................................................................ 163
IEEE 1588 GPIO Outputs ............................................................................................................................................................................. 163
13.2.2.1
13.2.2.2
GPIO Interrupt Polarity.................................................................................................................................................................................. 163
IEEE 1588 GPIO Interrupts........................................................................................................................................................................... 164
13.2.2 GPIO Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
13.3
LED Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Chapter 14 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
14.1 TX/RX FIFO Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.1.1 TX/RX Data FIFO’s. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.1.2 TX/RX Status FIFO’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.1.3 Direct FIFO Access Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.2 System Control and Status Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.2.1 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
167
167
167
167
168
172
14.2.1.1
14.2.1.2
14.2.1.3
14.2.1.4
Interrupt Configuration Register (IRQ_CFG) ................................................................................................................................................ 172
Interrupt Status Register (INT_STS)............................................................................................................................................................. 174
Interrupt Enable Register (INT_EN).............................................................................................................................................................. 177
FIFO Level Interrupt Register (FIFO_INT) .................................................................................................................................................... 179
14.2.2.1
14.2.2.2
14.2.2.3
14.2.2.4
14.2.2.5
14.2.2.6
14.2.2.7
14.2.2.8
14.2.2.9
Receive Configuration Register (RX_CFG) .................................................................................................................................................. 180
Transmit Configuration Register (TX_CFG).................................................................................................................................................. 182
Receive Datapath Control Register (RX_DP_CTRL).................................................................................................................................... 183
RX FIFO Information Register (RX_FIFO_INF) ............................................................................................................................................ 184
TX FIFO Information Register (TX_FIFO_INF)............................................................................................................................................. 185
Host MAC RX Dropped Frames Counter Register (RX_DROP)................................................................................................................... 186
Host MAC CSR Interface Command Register (MAC_CSR_CMD)............................................................................................................... 187
Host MAC CSR Interface Data Register (MAC_CSR_DATA) ...................................................................................................................... 188
Host MAC Automatic Flow Control Configuration Register (AFC_CFG) ...................................................................................................... 189
14.2.2 Host MAC & FIFO’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
SMSC LAN9312
7
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.3 GPIO/LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
14.2.3.1
14.2.3.2
14.2.3.3
14.2.3.4
General Purpose I/O Configuration Register (GPIO_CFG) .......................................................................................................................... 192
General Purpose I/O Data & Direction Register (GPIO_DATA_DIR) ........................................................................................................... 194
General Purpose I/O Interrupt Status and Enable Register (GPIO_INT_STS_EN)...................................................................................... 195
LED Configuration Register (LED_CFG) ...................................................................................................................................................... 196
14.2.4.1
14.2.4.2
EEPROM Command Register (E2P_CMD) .................................................................................................................................................. 197
EEPROM Data Register (E2P_DATA).......................................................................................................................................................... 200
14.2.5.1
14.2.5.2
14.2.5.3
14.2.5.4
14.2.5.5
14.2.5.6
14.2.5.7
14.2.5.8
14.2.5.9
14.2.5.10
14.2.5.11
14.2.5.12
14.2.5.13
14.2.5.14
14.2.5.15
14.2.5.16
14.2.5.17
14.2.5.18
14.2.5.19
14.2.5.20
14.2.5.21
14.2.5.22
14.2.5.23
14.2.5.24
Port x 1588 Clock High-DWORD Receive Capture Register (1588_CLOCK_HI_RX_CAPTURE_x) .......................................................... 201
Port x 1588 Clock Low-DWORD Receive Capture Register (1588_CLOCK_LO_RX_CAPTURE_x) .......................................................... 202
Port x 1588 Sequence ID, Source UUID High-WORD Receive Capture Register (1588_SEQ_ID_SRC_UUID_HI_RX_CAPTURE_x)..... 203
Port x 1588 Source UUID Low-DWORD Receive Capture Register (1588_SRC_UUID_LO_RX_CAPTURE_x)........................................ 204
Port x 1588 Clock High-DWORD Transmit Capture Register (1588_CLOCK_HI_TX_CAPTURE_x).......................................................... 205
Port x 1588 Clock Low-DWORD Transmit Capture Register (1588_CLOCK_LO_TX_CAPTURE_x) ......................................................... 206
Port x 1588 Sequence ID, Source UUID High-WORD Transmit Capture Register (1588_SEQ_ID_SRC_UUID_HI_TX_CAPTURE_x) .... 207
Port x 1588 Source UUID Low-DWORD Transmit Capture Register (1588_SRC_UUID_LO_TX_CAPTURE_x) ....................................... 208
GPIO 8 1588 Clock High-DWORD Capture Register (1588_CLOCK_HI_CAPTURE_GPIO_8).................................................................. 209
GPIO 8 1588 Clock Low-DWORD Capture Register (1588_CLOCK_LO_CAPTURE_GPIO_8) ................................................................. 210
GPIO 9 1588 Clock High-DWORD Capture Register (1588_CLOCK_HI_CAPTURE_GPIO_9).................................................................. 211
GPIO 9 1588 Clock Low-DWORD Capture Register (1588_CLOCK_LO_CAPTURE_GPIO_9) ................................................................. 212
1588 Clock High-DWORD Register (1588_CLOCK_HI)............................................................................................................................... 213
1588 Clock Low-DWORD Register (1588_CLOCK_LO) .............................................................................................................................. 214
1588 Clock Addend Register (1588_CLOCK_ADDEND) ............................................................................................................................. 215
1588 Clock Target High-DWORD Register (1588_CLOCK_TARGET_HI)................................................................................................... 216
1588 Clock Target Low-DWORD Register (1588_CLOCK_TARGET_LO) .................................................................................................. 217
1588 Clock Target Reload High-DWORD Register (1588_CLOCK_TARGET_RELOAD_HI) ..................................................................... 218
1588 Clock Target Reload/Add Low-DWORD Register (1588_CLOCK_TARGET_RELOAD_LO).............................................................. 219
1588 Auxiliary MAC Address High-WORD Register (1588_AUX_MAC_HI) ................................................................................................ 220
1588 Auxiliary MAC Address Low-DWORD Register (1588_AUX_MAC_LO) ............................................................................................. 221
1588 Configuration Register (1588_CONFIG).............................................................................................................................................. 222
1588 Interrupt Status and Enable Register (1588_INT_STS_EN)................................................................................................................ 226
1588 Command Register (1588_CMD) ........................................................................................................................................................ 228
14.2.6.1
14.2.6.2
14.2.6.3
14.2.6.4
14.2.6.5
14.2.6.6
14.2.6.7
14.2.6.8
Port 1 Manual Flow Control Register (MANUAL_FC_1)............................................................................................................................... 229
Port 2 Manual Flow Control Register (MANUAL_FC_2)............................................................................................................................... 231
Port 0(Host MAC) Manual Flow Control Register (MANUAL_FC_MII) ......................................................................................................... 233
Switch Fabric CSR Interface Data Register (SWITCH_CSR_DATA) ........................................................................................................... 235
Switch Fabric CSR Interface Command Register (SWITCH_CSR_CMD) ................................................................................................... 236
Switch Fabric MAC Address High Register (SWITCH_MAC_ADDRH) ........................................................................................................ 238
Switch Fabric MAC Address Low Register (SWITCH_MAC_ADDRL) ......................................................................................................... 239
Switch Fabric CSR Interface Direct Data Register (SWITCH_CSR_DIRECT_DATA) ................................................................................. 240
14.2.7.1
14.2.7.2
PHY Management Interface Data Register (PMI_DATA) ............................................................................................................................. 243
PHY Management Interface Access Register (PMI_ACCESS) .................................................................................................................... 244
14.2.8.1
14.2.8.2
14.2.8.3
14.2.8.4
14.2.8.5
14.2.8.6
14.2.8.7
14.2.8.8
Virtual PHY Basic Control Register (VPHY_BASIC_CTRL) ......................................................................................................................... 246
Virtual PHY Basic Status Register (VPHY_BASIC_STATUS)...................................................................................................................... 248
Virtual PHY Identification MSB Register (VPHY_ID_MSB) .......................................................................................................................... 250
Virtual PHY Identification LSB Register (VPHY_ID_LSB) ............................................................................................................................ 251
Virtual PHY Auto-Negotiation Advertisement Register (VPHY_AN_ADV).................................................................................................... 252
Virtual PHY Auto-Negotiation Link Partner Base Page Ability Register (VPHY_AN_LP_BASE_ABILITY) .................................................. 254
Virtual PHY Auto-Negotiation Expansion Register (VPHY_AN_EXP) .......................................................................................................... 256
Virtual PHY Special Control/Status Register (VPHY_SPECIAL_CONTROL_STATUS) .............................................................................. 257
14.2.9.1
14.2.9.2
14.2.9.3
14.2.9.4
14.2.9.5
14.2.9.6
14.2.9.7
14.2.9.8
Chip ID and Revision (ID_REV).................................................................................................................................................................... 259
Byte Order Test Register (BYTE_TEST) ...................................................................................................................................................... 260
Hardware Configuration Register (HW_CFG)............................................................................................................................................... 261
Power Management Control Register (PMT_CTRL) .................................................................................................................................... 263
General Purpose Timer Configuration Register (GPT_CFG) ....................................................................................................................... 266
General Purpose Timer Count Register (GPT_CNT) ................................................................................................................................... 267
Free Running 25MHz Counter Register (FREE_RUN)................................................................................................................................. 268
Reset Control Register (RESET_CTL) ......................................................................................................................................................... 269
14.2.4 EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
14.2.5 IEEE 1588 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
14.2.6 Switch Fabric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
14.2.7 PHY Management Interface (PMI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243
14.2.8 Virtual PHY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
14.2.9 Miscellaneous. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 259
14.3 Host MAC Control and Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.1 Host MAC Control Register (HMAC_CR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.2 Host MAC Address High Register (HMAC_ADDRH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.3 Host MAC Address Low Register (HMAC_ADDRL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.4 Host MAC Multicast Hash Table High Register (HMAC_HASHH) . . . . . . . . . . . . . . . . . . . . . . .
14.3.5 Host MAC Multicast Hash Table Low Register (HMAC_HASHL). . . . . . . . . . . . . . . . . . . . . . . .
14.3.6 Host MAC MII Access Register (HMAC_MII_ACC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.7 Host MAC MII Data Register (HMAC_MII_DATA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.8 Host MAC Flow Control Register (HMAC_FLOW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.9 Host MAC VLAN1 Tag Register (HMAC_VLAN1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision 2.0 (02-14-13)
8
DATASHEET
270
271
274
275
276
277
278
279
280
282
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.10 Host MAC VLAN2 Tag Register (HMAC_VLAN2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.11 Host MAC Wake-up Frame Filter Register (HMAC_WUFF). . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.12 Host MAC Wake-up Control and Status Register (HMAC_WUCSR) . . . . . . . . . . . . . . . . . . . . .
14.4 Ethernet PHY Control and Status Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.4.1 Virtual PHY Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.4.2 Port 1 & 2 PHY Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
283
284
285
286
286
286
14.4.2.1
14.4.2.2
14.4.2.3
14.4.2.4
14.4.2.5
14.4.2.6
14.4.2.7
14.4.2.8
14.4.2.9
14.4.2.10
14.4.2.11
14.4.2.12
14.4.2.13
Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x) ................................................................................................................ 288
Port x PHY Basic Status Register (PHY_BASIC_STATUS_x) ..................................................................................................................... 290
Port x PHY Identification MSB Register (PHY_ID_MSB_x).......................................................................................................................... 292
Port x PHY Identification LSB Register (PHY_ID_LSB_x)............................................................................................................................ 293
Port x PHY Auto-Negotiation Advertisement Register (PHY_AN_ADV_x) ................................................................................................... 294
Port x PHY Auto-Negotiation Link Partner Base Page Ability Register (PHY_AN_LP_BASE_ABILITY_x) ................................................. 297
Port x PHY Auto-Negotiation Expansion Register (PHY_AN_EXP_x) ......................................................................................................... 299
Port x PHY Mode Control/Status Register (PHY_MODE_CONTROL_STATUS_x)..................................................................................... 300
Port x PHY Special Modes Register (PHY_SPECIAL_MODES_x) .............................................................................................................. 301
Port x PHY Special Control/Status Indication Register (PHY_SPECIAL_CONTROL_STAT_IND_x) .......................................................... 303
Port x PHY Interrupt Source Flags Register (PHY_INTERRUPT_SOURCE_x)........................................................................................... 305
Port x PHY Interrupt Mask Register (PHY_INTERRUPT_MASK_x) ............................................................................................................ 306
Port x PHY Special Control/Status Register (PHY_SPECIAL_CONTROL_STATUS_x).............................................................................. 307
14.5.1.1
14.5.1.2
14.5.1.3
14.5.1.4
Switch Device ID Register (SW_DEV_ID) .................................................................................................................................................... 319
Switch Reset Register (SW_RESET) ........................................................................................................................................................... 320
Switch Global Interrupt Mask Register (SW_IMR)........................................................................................................................................ 321
Switch Global Interrupt Pending Register (SW_IPR).................................................................................................................................... 322
14.5.2.1
14.5.2.2
14.5.2.3
14.5.2.4
14.5.2.5
14.5.2.6
14.5.2.7
14.5.2.8
14.5.2.9
14.5.2.10
14.5.2.11
14.5.2.12
14.5.2.13
14.5.2.14
14.5.2.15
14.5.2.16
14.5.2.17
14.5.2.18
14.5.2.19
14.5.2.20
14.5.2.21
14.5.2.22
14.5.2.23
14.5.2.24
14.5.2.25
14.5.2.26
14.5.2.27
14.5.2.28
14.5.2.29
14.5.2.30
14.5.2.31
14.5.2.32
14.5.2.33
14.5.2.34
14.5.2.35
14.5.2.36
14.5.2.37
14.5.2.38
14.5.2.39
14.5.2.40
14.5.2.41
14.5.2.42
14.5.2.43
14.5.2.44
Port x MAC Version ID Register (MAC_VER_ID_x) ..................................................................................................................................... 323
Port x MAC Receive Configuration Register (MAC_RX_CFG_x) ................................................................................................................. 324
Port x MAC Receive Undersize Count Register (MAC_RX_UNDSZE_CNT_x) ........................................................................................... 325
Port x MAC Receive 64 Byte Count Register (MAC_RX_64_CNT_x).......................................................................................................... 326
Port x MAC Receive 65 to 127 Byte Count Register (MAC_RX_65_TO_127_CNT_x)................................................................................ 327
Port x MAC Receive 128 to 255 Byte Count Register (MAC_RX_128_TO_255_CNT_x)............................................................................ 328
Port x MAC Receive 256 to 511 Byte Count Register (MAC_RX_256_TO_511_CNT_x)............................................................................ 329
Port x MAC Receive 512 to 1023 Byte Count Register (MAC_RX_512_TO_1023_CNT_x)........................................................................ 330
Port x MAC Receive 1024 to Max Byte Count Register (MAC_RX_1024_TO_MAX_CNT_x) ..................................................................... 331
Port x MAC Receive Oversize Count Register (MAC_RX_OVRSZE_CNT_x) ............................................................................................. 332
Port x MAC Receive OK Count Register (MAC_RX_PKTOK_CNT_x)......................................................................................................... 333
Port x MAC Receive CRC Error Count Register (MAC_RX_CRCERR_CNT_x).......................................................................................... 334
Port x MAC Receive Multicast Count Register (MAC_RX_MULCST_CNT_x) ............................................................................................. 335
Port x MAC Receive Broadcast Count Register (MAC_RX_BRDCST_CNT_x) ........................................................................................... 336
Port x MAC Receive Pause Frame Count Register (MAC_RX_PAUSE_CNT_x) ........................................................................................ 337
Port x MAC Receive Fragment Error Count Register (MAC_RX_FRAG_CNT_x)........................................................................................ 338
Port x MAC Receive Jabber Error Count Register (MAC_RX_JABB_CNT_x) ............................................................................................. 339
Port x MAC Receive Alignment Error Count Register (MAC_RX_ALIGN_CNT_x) ...................................................................................... 340
Port x MAC Receive Packet Length Count Register (MAC_RX_PKTLEN_CNT_x) ..................................................................................... 341
Port x MAC Receive Good Packet Length Count Register (MAC_RX_GOODPKTLEN_CNT_x) ................................................................ 342
Port x MAC Receive Symbol Error Count Register (MAC_RX_SYMBOL_CNT_x) ...................................................................................... 343
Port x MAC Receive Control Frame Count Register (MAC_RX_CTLFRM_CNT_x) .................................................................................... 344
Port x MAC Transmit Configuration Register (MAC_TX_CFG_x) ................................................................................................................ 345
Port x MAC Transmit Flow Control Settings Register (MAC_TX_FC_SETTINGS_x) .................................................................................. 346
Port x MAC Transmit Deferred Count Register (MAC_TX_DEFER_CNT_x) ............................................................................................... 347
Port x MAC Transmit Pause Count Register (MAC_TX_PAUSE_CNT_x) ................................................................................................... 348
Port x MAC Transmit OK Count Register (MAC_TX_PKTOK_CNT_x) ........................................................................................................ 349
Port x MAC Transmit 64 Byte Count Register (MAC_TX_64_CNT_x) ......................................................................................................... 350
Port x MAC Transmit 65 to 127 Byte Count Register (MAC_TX_65_TO_127_CNT_x) ............................................................................... 351
Port x MAC Transmit 128 to 255 Byte Count Register (MAC_TX_128_TO_255_CNT_x) ........................................................................... 352
Port x MAC Transmit 256 to 511 Byte Count Register (MAC_TX_256_TO_511_CNT_x) ........................................................................... 353
Port x MAC Transmit 512 to 1023 Byte Count Register (MAC_TX_512_TO_1023_CNT_x) ....................................................................... 354
Port x MAC Transmit 1024 to Max Byte Count Register (MAC_TX_1024_TO_MAX_CNT_x)..................................................................... 355
Port x MAC Transmit Undersize Count Register (MAC_TX_UNDSZE_CNT_x) .......................................................................................... 356
Port x MAC Transmit Packet Length Count Register (MAC_TX_PKTLEN_CNT_x) .................................................................................... 357
Port x MAC Transmit Broadcast Count Register (MAC_TX_BRDCST_CNT_x) .......................................................................................... 358
Port x MAC Transmit Multicast Count Register (MAC_TX_MULCST_CNT_x) ............................................................................................ 359
Port x MAC Transmit Late Collision Count Register (MAC_TX_LATECOL_CNT_x) ................................................................................... 360
Port x MAC Transmit Excessive Collision Count Register (MAC_TX_EXCCOL_CNT_x)............................................................................ 361
Port x MAC Transmit Single Collision Count Register (MAC_TX_SNGLECOL_CNT_x) ............................................................................. 362
Port x MAC Transmit Multiple Collision Count Register (MAC_TX_MULTICOL_CNT_x) ............................................................................ 363
Port x MAC Transmit Total Collision Count Register (MAC_TX_TOTALCOL_CNT_x)................................................................................ 364
Port x MAC Interrupt Mask Register (MAC_IMR_x) ..................................................................................................................................... 365
Port x MAC Interrupt Pending Register (MAC_IPR_x) ................................................................................................................................. 366
14.5.3.1
14.5.3.2
14.5.3.3
14.5.3.4
14.5.3.5
14.5.3.6
Switch Engine ALR Command Register (SWE_ALR_CMD) ........................................................................................................................ 367
Switch Engine ALR Write Data 0 Register (SWE_ALR_WR_DAT_0) .......................................................................................................... 368
Switch Engine ALR Write Data 1 Register (SWE_ALR_WR_DAT_1) .......................................................................................................... 369
Switch Engine ALR Read Data 0 Register (SWE_ALR_RD_DAT_0)........................................................................................................... 371
Switch Engine ALR Read Data 1 Register (SWE_ALR_RD_DAT_1)........................................................................................................... 372
Switch Engine ALR Command Status Register (SWE_ALR_CMD_STS) .................................................................................................... 374
14.5 Switch Fabric Control and Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
14.5.1 General Switch CSRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
14.5.2 Switch Port 0, Port 1, and Port 2 CSRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
14.5.3 Switch Engine CSRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367
SMSC LAN9312
9
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.7
14.5.3.8
14.5.3.9
14.5.3.10
14.5.3.11
14.5.3.12
14.5.3.13
14.5.3.14
14.5.3.15
14.5.3.16
14.5.3.17
14.5.3.18
14.5.3.19
14.5.3.20
14.5.3.21
14.5.3.22
14.5.3.23
14.5.3.24
14.5.3.25
14.5.3.26
Switch Engine ALR Configuration Register (SWE_ALR_CFG) .................................................................................................................... 375
Switch Engine VLAN Command Register (SWE_VLAN_CMD).................................................................................................................... 376
Switch Engine VLAN Write Data Register (SWE_VLAN_WR_DATA).......................................................................................................... 377
Switch Engine VLAN Read Data Register (SWE_VLAN_RD_DATA) .......................................................................................................... 378
Switch Engine VLAN Command Status Register (SWE_VLAN_CMD_STS) ............................................................................................... 379
Switch Engine DIFFSERV Table Command Register (SWE_DIFFSERV_TBL_CFG)................................................................................. 380
Switch Engine DIFFSERV Table Write Data Register (SWE_DIFFSERV_TBL_WR_DATA) ...................................................................... 381
Switch Engine DIFFSERV Table Read Data Register (SWE_DIFFSERV_TBL_RD_DATA) ....................................................................... 382
Switch Engine DIFFSERV Table Command Status Register (SWE_DIFFSERV_TBL_CMD_STS) ............................................................ 383
Switch Engine Global Ingress Configuration Register (SWE_GLOBAL_INGRSS_CFG)............................................................................. 384
Switch Engine Port Ingress Configuration Register (SWE_PORT_INGRSS_CFG) ..................................................................................... 386
Switch Engine Admit Only VLAN Register (SWE_ADMT_ONLY_VLAN)..................................................................................................... 387
Switch Engine Port State Register (SWE_PORT_STATE)........................................................................................................................... 388
Switch Engine Priority to Queue Register (SWE_PRI_TO_QUE) ................................................................................................................ 389
Switch Engine Port Mirroring Register (SWE_PORT_MIRROR).................................................................................................................. 390
Switch Engine Ingress Port Type Register (SWE_INGRSS_PORT_TYP) ................................................................................................... 391
Switch Engine Broadcast Throttling Register (SWE_BCST_THROT) .......................................................................................................... 392
Switch Engine Admit Non Member Register (SWE_ADMT_N_MEMBER)................................................................................................... 393
Switch Engine Ingress Rate Configuration Register (SWE_INGRSS_RATE_CFG) .................................................................................... 394
Switch Engine Ingress Rate Command Register (SWE_INGRSS_RATE_CMD)......................................................................................... 395
14.5.3.27
14.5.3.28
14.5.3.29
14.5.3.30
14.5.3.31
14.5.3.32
14.5.3.33
14.5.3.34
14.5.3.35
14.5.3.36
14.5.3.37
14.5.3.38
14.5.3.39
14.5.3.40
Switch Engine Ingress Rate Command Status Register (SWE_INGRSS_RATE_CMD_STS) .................................................................... 397
Switch Engine Ingress Rate Write Data Register (SWE_INGRSS_RATE_WR_DATA)............................................................................... 398
Switch Engine Ingress Rate Read Data Register (SWE_INGRSS_RATE_RD_DATA) ............................................................................... 399
Switch Engine Port 0 Ingress Filtered Count Register (SWE_FILTERED_CNT_MII) .................................................................................. 400
Switch Engine Port 1 Ingress Filtered Count Register (SWE_FILTERED_CNT_1) ..................................................................................... 401
Switch Engine Port 2 Ingress Filtered Count Register (SWE_FILTERED_CNT_2) ..................................................................................... 402
Switch Engine Port 0 Ingress VLAN Priority Regeneration Table Register (SWE_INGRSS_REGEN_TBL_MII) ........................................ 403
Switch Engine Port 1 Ingress VLAN Priority Regeneration Table Register (SWE_INGRSS_REGEN_TBL_1) ........................................... 404
Switch Engine Port 2 Ingress VLAN Priority Regeneration Table Register (SWE_INGRSS_REGEN_TBL_2) ........................................... 405
Switch Engine Port 0 Learn Discard Count Register (SWE_LRN_DISCRD_CNT_MII) ............................................................................... 406
Switch Engine Port 1 Learn Discard Count Register (SWE_LRN_DISCRD_CNT_1) .................................................................................. 407
Switch Engine Port 2 Learn Discard Count Register (SWE_LRN_DISCRD_CNT_2) .................................................................................. 408
Switch Engine Interrupt Mask Register (SWE_IMR)..................................................................................................................................... 409
Switch Engine Interrupt Pending Register (SWE_IPR)................................................................................................................................. 410
14.5.4.1
14.5.4.2
14.5.4.3
14.5.4.4
14.5.4.5
14.5.4.6
14.5.4.7
14.5.4.8
14.5.4.9
14.5.4.10
14.5.4.11
14.5.4.12
14.5.4.13
14.5.4.14
14.5.4.15
14.5.4.16
14.5.4.17
14.5.4.18
14.5.4.19
14.5.4.20
14.5.4.21
14.5.4.22
14.5.4.23
14.5.4.24
14.5.4.25
14.5.4.26
14.5.4.27
Buffer Manager Configuration Register (BM_CFG) ...................................................................................................................................... 412
Buffer Manager Drop Level Register (BM_DROP_LVL)............................................................................................................................... 413
Buffer Manager Flow Control Pause Level Register (BM_FC_PAUSE_LVL)............................................................................................... 414
Buffer Manager Flow Control Resume Level Register (BM_FC_RESUME_LVL) ........................................................................................ 415
Buffer Manager Broadcast Buffer Level Register (BM_BCST_LVL)............................................................................................................. 416
Buffer Manager Port 0 Drop Count Register (BM_DRP_CNT_SRC_MII) .................................................................................................... 417
Buffer Manager Port 1 Drop Count Register (BM_DRP_CNT_SRC_1) ....................................................................................................... 418
Buffer Manager Port 2 Drop Count Register (BM_DRP_CNT_SRC_2) ....................................................................................................... 419
Buffer Manager Reset Status Register (BM_RST_STS) .............................................................................................................................. 420
Buffer Manager Random Discard Table Command Register (BM_RNDM_DSCRD_TBL_CMD) ................................................................ 421
Buffer Manager Random Discard Table Write Data Register (BM_RNDM_DSCRD_TBL_WDATA) ........................................................... 422
Buffer Manager Random Discard Table Read Data Register (BM_RNDM_DSCRD_TBL_RDATA)............................................................ 423
Buffer Manager Egress Port Type Register (BM_EGRSS_PORT_TYPE) ................................................................................................... 424
Buffer Manager Port 0 Egress Rate Priority Queue 0/1 Register (BM_EGRSS_RATE_00_01) .................................................................. 426
Buffer Manager Port 0 Egress Rate Priority Queue 2/3 Register (BM_EGRSS_RATE_02_03) .................................................................. 427
Buffer Manager Port 1 Egress Rate Priority Queue 0/1 Register (BM_EGRSS_RATE_10_11) .................................................................. 428
Buffer Manager Port 1 Egress Rate Priority Queue 2/3 Register (BM_EGRSS_RATE_12_13) .................................................................. 429
Buffer Manager Port 2 Egress Rate Priority Queue 0/1 Register (BM_EGRSS_RATE_20_21) .................................................................. 430
Buffer Manager Port 2 Egress Rate Priority Queue 2/3 Register (BM_EGRSS_RATE_22_23) .................................................................. 431
Buffer Manager Port 0 Default VLAN ID and Priority Register (BM_VLAN_MII) .......................................................................................... 432
Buffer Manager Port 1 Default VLAN ID and Priority Register (BM_VLAN_1) ............................................................................................. 433
Buffer Manager Port 2 Default VLAN ID and Priority Register (BM_VLAN_2) ............................................................................................. 434
Buffer Manager Port 0 Ingress Rate Drop Count Register (BM_RATE_DRP_CNT_SRC_MII) ................................................................... 435
Buffer Manager Port 1 Ingress Rate Drop Count Register (BM_RATE_DRP_CNT_SRC_1) ...................................................................... 436
Buffer Manager Port 2 Ingress Rate Drop Count Register (BM_RATE_DRP_CNT_SRC_2) ...................................................................... 437
Buffer Manager Interrupt Mask Register (BM_IMR) ..................................................................................................................................... 438
Buffer Manager Interrupt Pending Register (BM_IPR) ................................................................................................................................. 439
14.5.3.26.1Ingress Rate Table Registers .................................................................................................396
14.5.4 Buffer Manager CSRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
Chapter 15 Operational Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441
15.1 Absolute Maximum Ratings*. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.2 Operating Conditions** . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3 Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.4 DC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.5 AC Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.5.1 Equivalent Test Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.5.2 Reset and Configuration Strap Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.5.3 Power-On Configuration Strap Valid Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.5.4 PIO Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.5.5 PIO Burst Read Cycle Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Revision 2.0 (02-14-13)
10
DATASHEET
441
441
442
443
444
444
445
446
447
448
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.5.6 RX Data FIFO Direct PIO Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.5.7 RX Data FIFO Direct PIO Burst Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.5.8 PIO Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.5.9 TX Data FIFO Direct PIO Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.5.10 Microwire Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.6 Clock Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
449
450
451
452
453
454
Chapter 16 Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455
16.1
16.2
128-VTQFP Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455
128-XVTQFP Package Outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457
Chapter 17 Datasheet Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 459
SMSC LAN9312
11
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
List of Figures
Figure 2.1 Internal LAN9312 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 2.2 System Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 3.1 LAN9312 128-VTQFP Pin Assignments (TOP VIEW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 3.2 LAN9312 128-XVTQFP Pin Assignments (TOP VIEW). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 4.1 PME and PME_INT Signal Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 5.1 Functional Interrupt Register Hierarchy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Figure 6.1 Switch Fabric CSR Write Access Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 6.2 Switch Fabric CSR Read Access Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 6.3 ALR Table Entry Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 6.4 Switch Engine Transmit Queue Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figure 6.5 Switch Engine Transmit Queue Calculation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Figure 6.6 VLAN Table Entry Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Figure 6.7 Switch Engine Ingress Flow Priority Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Figure 6.8 Switch Engine Ingress Flow Priority Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Figure 6.9 Hybrid Port Tagging and Un-tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Figure 7.1 Port x PHY Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Figure 7.2 100BASE-TX Transmit Data Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Figure 7.3 100BASE-TX Receive Data Path. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Figure 7.4 Direct Cable Connection vs. Cross-Over Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . 93
Figure 8.1 Little Endian Byte Ordering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Figure 8.2 Big Endian Byte Ordering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Figure 8.3 Functional Timing for PIO Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Figure 8.4 Functional Timing for PIO Burst Read Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Figure 8.5 Functional Timing for RX Data FIFO Direct PIO Read Operation . . . . . . . . . . . . . . . . . . . . 108
Figure 8.6 Functional Timing for RX Data FIFO Direct PIO Burst Read Operation . . . . . . . . . . . . . . . 109
Figure 8.7 Functional Timing for PIO Write Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Figure 8.8 Functional Timing for TX Data FIFO Direct PIO Write Operation . . . . . . . . . . . . . . . . . . . . 111
Figure 9.1 VLAN Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Figure 9.2 Example EEPROM MAC Address Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Figure 9.3 Simplified Host TX Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Figure 9.4 TX Buffer Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Figure 9.5 TX Example 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Figure 9.6 TX Example 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
Figure 9.7 Host Receive Routine Using Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Figure 9.8 Host Receive Routine Using Polling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Figure 9.9 RX Packet Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Figure 10.1 EEPROM Access Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Figure 10.2 I2C Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Figure 10.3 I2C EEPROM Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Figure 10.4 I2C EEPROM Byte Read . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Figure 10.5 I2C EEPROM Sequential Byte Reads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Figure 10.6 I2C EEPROM Byte Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Figure 10.7 EEPROM ERASE Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Figure 10.8 EEPROM ERAL Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Figure 10.9 EEPROM EWDS Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Figure 10.10EEPROM EWEN Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Figure 10.11EEPROM READ Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Figure 10.12EEPROM WRITE Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Figure 10.13EEPROM WRAL Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Figure 10.14EEPROM Loader Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Figure 11.1 IEEE 1588 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Figure 11.2 IEEE 1588 Message Time Stamp Point. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Revision 2.0 (02-14-13)
12
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Figure 14.1 LAN9312 Base Register Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 15.1 Output Equivalent Test Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 15.2 nRST Reset Pin Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 15.3 Power-On Configuration Strap Latching Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 15.4 PIO Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 15.5 PIO Burst Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 15.6 RX Data FIFO Direct PIO Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 15.7 RX Data FIFO Direct PIO Burst Read Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 15.8 PIO Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 15.9 TX Data FIFO Direct PIO Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 15.10Microwire Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 16.1 128-VTQFP Package Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 16.2 128-VTQFP Recommended PCB Land Pattern. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 16.3 128-XVTQFP Package Definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 16.4 128-XVTQFP Recommended PCB Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMSC LAN9312
13
DATASHEET
166
444
445
446
447
448
449
450
451
452
453
455
456
457
458
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
List of Tables
Table 1.1 Buffer Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 1.2 Register Bit Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table 3.1 LAN Port 1 Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 3.2 LAN Port 2 Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 3.3 LAN Port 1 & 2 Power and Common Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 3.4 Host Bus Interface Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 3.5 EEPROM Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 3.6 Dedicated Configuration Strap Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table 3.7 Miscellaneous Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 3.8 PLL Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table 3.9 Core and I/O Power and Ground Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table 3.10 No-Connect Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table 4.1 Reset Sources and Affected LAN9312 Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 4.2 Soft-Strap Configuration Strap Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 4.3 Hard-Strap Configuration Strap Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 6.1 Switch Fabric Flow Control Enable Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Table 6.2 Spanning Tree States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Table 6.3 Typical Ingress Rate Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Table 6.4 Typical Broadcast Rate Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Table 6.5 Typical Egress Rate Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Table 7.1 Default PHY Serial MII Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Table 7.2 4B/5B Code Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Table 7.3 PHY Interrupt Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Table 8.1 Read After Write Timing Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Table 8.2 Read After Read Timing Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Table 9.1 Address Filtering Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Table 9.2 Wake-Up Frame Filter Register Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Table 9.3 Filter i Byte Mask Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Table 9.4 Filter i Command Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Table 9.5 Filter i Offset Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Table 9.6 Filter i CRC-16 Bit Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Table 9.7 EEPROM Byte Ordering and Register Correlation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Table 9.8 TX/RX FIFO Configurable Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Table 9.9 Valid TX/RX FIFO Allocations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Table 9.10 TX Command 'A' Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Table 9.11 TX Command 'B' Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Table 9.12 TX DATA Start Offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Table 10.1 I2C/Microwire Master Serial Management Pins Characteristics. . . . . . . . . . . . . . . . . . . . . . 137
Table 10.2 I2C EEPROM Size Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Table 10.3 Microwire EEPROM Size Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Table 10.4 Microwire Command Set for 7 Address Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Table 10.5 Microwire Command Set for 9 Address Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Table 10.6 Microwire Command Set for 11 Address Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Table 10.7 EEPROM Contents Format Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Table 10.8 EEPROM Configuration Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Table 11.1 IEEE 1588 Message Type Detection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Table 11.2 Time Stamp Capture Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Table 11.3 PTP Multicast Addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
Table 11.4 Typical IEEE 1588 Clock Addend Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Table 13.1 LED Operation as a Function of LED_CFG[9:8] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Table 14.1 System Control and Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Table 14.2 Backpressure Duration Bit Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
Revision 2.0 (02-14-13)
14
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.3 Switch Fabric CSR to SWITCH_CSR_DIRECT_DATA Address Range Map . . . . . . . . . . . .
Table 14.4 Virtual PHY MII Serially Adressable Register Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 14.5 Emulated Link Partner Pause Flow Control Ability Default Values . . . . . . . . . . . . . . . . . . . .
Table 14.6 Host MAC Adressable Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 14.7 Port 1 & 2 PHY MII Serially Adressable Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 14.8 10BASE-T Full Duplex Advertisement Default Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 14.9 10BASE-T Half Duplex Advertisement Bit Default Value . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 14.10MODE[2:0] Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 14.11Auto-MDIX Enable and Auto-MDIX State Bit Functionality . . . . . . . . . . . . . . . . . . . . . . . . .
Table 14.12Indirectly Accessible Switch Control and Status Registers . . . . . . . . . . . . . . . . . . . . . . . . .
Table 14.13Metering/Color Table Register Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.1 Supply and Current (10BASE-T Full-Duplex) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.2 Supply and Current (100BASE-TX Full-Duplex) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.3 I/O Buffer Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.4 100BASE-TX Transceiver Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.5 10BASE-T Transceiver Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.6 nRST Reset Pin Timing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.7 Power-On Configuration Strap Latching Timing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.8 PIO Read Cycle Timing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.9 PIO Burst Read Cycle Timing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.10RX Data FIFO Direct PIO Read Cycle Timing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.11RX Data FIFO Direct PIO Burst Read Cycle Timing Values . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.12PIO Write Cycle Timing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.13TX Data FIFO Direct PIO Write Cycle Timing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.14Microwire Timing Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 15.15LAN9312Crystal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 16.1 128-VTQFP Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 16.2 128-XVTQFP Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 17.1 Customer Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMSC LAN9312
15
DATASHEET
240
245
255
270
286
295
296
301
304
308
396
442
442
443
443
444
445
446
447
448
449
450
451
452
453
454
455
458
459
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 1 Preface
1.1
General Terms
100BT
100BASE-T (100Mbps Fast Ethernet, IEEE 802.3u)
ADC
Analog-to-Digital Converter
ALR
Address Logic Resolution
BLW
Baseline Wander
BM
Buffer Manager - Part of the switch fabric
BPDU
Bridge Protocol Data Unit - Messages which carry the Spanning Tree
Protocol information
Byte
8-bits
CSMA/CD
Carrier Sense Multiple Access / Collision Detect
CSR
Control and Status Registers
CTR
Counter
DA
Destination Address
DWORD
32-bits
EPC
EEPROM Controller
FCS
Frame Check Sequence - The extra checksum characters added to the end
of an Ethernet frame, used for error detection and correction.
FIFO
First In First Out buffer
FSM
Finite State Machine
GPIO
General Purpose I/O
HBI
Host Bus Interface. The physical bus connecting the LAN9312 to the host.
Also referred to as the Host Bus.
HBIC
Host Bus Interface Controller. The hardware module that interfaces the
LAN9312 to the HBI.
Host
External system (Includes processor, application software, etc.)
IGMP
Internet Group Management Protocol
Inbound
Refers to data input to the LAN9312 from the host
Level-Triggered Sticky Bit
This type of status bit is set whenever the condition that it represents is
asserted. The bit remains set until the condition is no longer true, and the
status bit is cleared by writing a zero.
lsb
Least Significant Bit
LSB
Least Significant Byte
MDI
Medium Dependant Interface
MDIX
Media Independent Interface with Crossover
Revision 2.0 (02-14-13)
16
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
MII
Media Independent Interface
MIIM
Media Independent Interface Management
MIL
MAC Interface Layer
MLT-3
Multi-Level Transmission Encoding (3-Levels). A tri-level encoding method
where a change in the logic level represents a code bit “1” and the logic
output remaining at the same level represents a code bit “0”.
msb
Most Significant Bit
MSB
Most Significant Byte
NRZI
Non Return to Zero Inverted. This encoding method inverts the signal for a
“1” and leaves the signal unchanged for a “0”
N/A
Not Applicable
NC
No Connect
OUI
Organizationally Unique Identifier
Outbound
Refers to data output from the LAN9312 to the host
PIO cycle
Program I/O cycle. An SRAM-like read or write cycle on the HBI.
PISO
Parallel In Serial Out
PLL
Phase Locked Loop
PTP
Precision Time Protocol
RESERVED
Refers to a reserved bit field or address. Unless otherwise noted, reserved
bits must always be zero for write operations. Unless otherwise noted, values
are not guaranteed when reading reserved bits. Unless otherwise noted, do
not read or write to reserved addresses.
RTC
Real-Time Clock
SA
Source Address
SFD
Start of Frame Delimiter - The 8-bit value indicating the end of the preamble
of an Ethernet frame.
SIPO
Serial In Parallel Out
SMI
Serial Management Interface
SQE
Signal Quality Error (also known as “heartbeat”)
SSD
Start of Stream Delimiter
UDP
User Datagram Protocol - A connectionless protocol run on top of IP
networks
UUID
Universally Unique IDentifier
WORD
16-bits
SMSC LAN9312
17
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
1.2
Buffer Types
Table 1.1 describes the pin buffer type notation used in Chapter 3, "Pin Description and Configuration,"
on page 26 and throughout this document.
Table 1.1 Buffer Types
BUFFER TYPE
DESCRIPTION
IS
Schmitt-triggered Input
O8
Output with 8mA sink and 8mA source
OD8
Open-drain output with 8mA sink
O12
Output with 12mA sink and 12mA source
OD12
PU
Open-drain output with 12mA sink
50uA (typical) internal pull-up. Unless otherwise noted in the pin description, internal pullups are always enabled.
Note:
PD
Internal pull-up resistors prevent unconnected inputs from floating. Do not rely on
internal resistors to drive signals external to the LAN9312. When connected to a
load that must be pulled high, an external resistor must be added.
50uA (typical) internal pull-down. Unless otherwise noted in the pin description, internal
pull-downs are always enabled.
Note:
Internal pull-down resistors prevent unconnected inputs from floating. Do not rely
on internal resistors to drive signals external to the LAN9312. When connected to
a load that must be pulled low, an external resistor must be added.
AI
Analog input
AO
Analog output
AIO
Analog bi-directional
ICLK
Crystal oscillator input pin
OCLK
Crystal oscillator output pin
P
Revision 2.0 (02-14-13)
Power pin
18
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
1.3
Register Nomenclature
Table 1.2 describes the register bit attribute notation used throughout this document.
Table 1.2 Register Bit Types
REGISTER BIT TYPE
NOTATION
REGISTER BIT DESCRIPTION
R
Read: A register or bit with this attribute can be read.
W
Read: A register or bit with this attribute can be written.
RO
Read only: Read only. Writes have no effect.
WO
Write only: If a register or bit is write-only, reads will return unspecified data.
WC
Write One to Clear: writing a one clears the value. Writing a zero has no effect
WAC
Write Anything to Clear: writing anything clears the value.
RC
Read to Clear: Contents is cleared after the read. Writes have no effect.
LL
Latch Low: Clear on read of register.
LH
Latch High: Clear on read of register.
SC
Self-Clearing: Contents are self-cleared after the being set. Writes of zero have no
effect. Contents can be read.
SS
Self-Setting: Contents are self-setting after being cleared. Writes of one have no
effect. Contents can be read.
RO/LH
Read Only, Latch High: Bits with this attribute will stay high until the bit is read. After
it is read, the bit will either remain high if the high condition remains, or will go low if
the high condition has been removed. If the bit has not been read, the bit will remain
high regardless of a change to the high condition. This mode is used in some Ethernet
PHY registers.
NASR
Not Affected by Software Reset. The state of NASR bits do not change on assertion
of a software reset.
RESERVED
Reserved Field: Reserved fields must be written with zeros to ensure future
compatibility. The value of reserved bits is not guaranteed on a read.
Many of these register bit notations can be combined. Some examples of this are shown below:

R/W: Can be written. Will return current setting on a read.

R/WAC: Will return current setting on a read. Writing anything clears the bit.
SMSC LAN9312
19
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 2 Introduction
2.1
General Description
The LAN9312 is a full featured, 2 port 10/100 managed Ethernet switch designed for embedded
applications where performance, flexibility, ease of integration and system cost control are required.
The LAN9312 combines all the functions of a 10/100 switch system, including the switch fabric, packet
buffers, buffer manager, media access controllers (MACs), PHY transceivers, and host bus interface.
The LAN9312 complies with the IEEE 802.3 (full/half-duplex 10BASE-T and 100BASE-TX) Ethernet
protocol specification and 802.1D/802.1Q network management protocol specifications, enabling
compatibility with industry standard Ethernet and Fast Ethernet applications.
At the core of the LAN9312 is the high performance, high efficiency 3 port Ethernet switch fabric. The
switch fabric contains a 3 port VLAN layer 2 switch engine that supports untagged, VLAN tagged, and
priority tagged frames. The switch fabric provides an extensive feature set which includes spanning
tree protocol support, multicast packet filtering and Quality of Service (QoS) packet prioritization by
VLAN tag, destination address, port default value or DIFFSERV/TOS, allowing for a range of
prioritization implementations. 32K of buffer RAM allows for the storage of multiple packets while
forwarding operations are completed, and a 1K entry forwarding table provides ample room for MAC
address forwarding tables. Each port is allocated a cluster of 4 dynamic QoS queues which allow each
queue size to grow and shrink with traffic, effectively utilizing all available memory. This memory is
managed dynamically via the buffer manager block within the switch fabric. All aspects of the switch
fabric are managed via the switch fabric configuration and status registers, which are indirectly
accessible via the memory mapped system control and status registers.
The LAN9312 provides 2 switched ports. Each port is fully compliant with the IEEE 802.3 standard and
all internal MACs and PHYs support full/half duplex 10BASE-T and 100BASE-TX operation. The
LAN9312 provides 2 on-chip PHYs, 1 Virtual PHY and 3 MACs. The Virtual PHY and the Host MAC
are used to connect the LAN9312 switch fabric to the host bus interface. All ports support automatic
or manual full duplex flow control or half duplex backpressure (forced collision) flow control. Automatic
32-bit CRC generation/checking and automatic payload padding are supported to further reduce CPU
overhead. 2K jumbo packet (2048 byte) support allows for oversized packet transfers, effectively
increasing throughput while deceasing CPU load. All MAC and PHY related settings are fully
configurable via their respective registers within the LAN9312.
The integrated Host Bus Interface (HBI) easily interfaces to most 32-bit embedded CPU’s via a simple
SRAM like interface, enabling switch fabric access via the internal Host MAC and allowing full control
over the LAN9312 via memory mapped system control and status registers. The HBI supports 32-bit
operation with big, little, and mixed endian operations. Four separate FIFO mechanisms (TX/RX Data
FIFO’s, TX/RX Status FIFO’s) interface the HBI to the Host MAC and facilitate the transferring of
packet data and status information between the host CPU and the switch fabric. The LAN9312 also
provides power management features which allow for wake on LAN, wake on link status change
(energy detect), and magic packet wakeup detection. A configurable host interrupt pin allows the
device to inform the host CPU of any internal interrupts.
The LAN9312 contains an I2C/Microwire master EEPROM controller for connection to an optional
EEPROM. This allows for the storage and retrieval of static data. The internal EEPROM Loader can
be optionally configured to automatically load stored configuration settings from the EEPROM into the
LAN9312 at reset.
In addition to the primary functionality described above, the LAN9312 provides additional features
designed for extended functionality. These include a configurable 16-bit General Purpose Timer (GPT),
a 32-bit 25MHz free running counter, a 12-bit configurable GPIO/LED interface, and IEEE 1588 time
stamping on all ports and select GPIOs. The IEEE time stamp unit provides a 64-bit tunable clock for
accurate PTP timing and a timer comparator to allow time based interrupt generation.
The LAN9312’s performance, features and small size make it an ideal solution for many applications
in the consumer electronics and industrial automation markets. Targeted applications include: set top
boxes (cable, satellite and IP), digital televisions, digital video recorders, voice over IP and video phone
systems, home gateways, and test and measurement equipment.
Revision 2.0 (02-14-13)
20
DATASHEET
SMSC LAN9312
Revision 2.0 (02-14-13)
2.2
Block Diagram
IEEE 1588
Time Stamp
MII
10/100
PHY
MDIO
10/100
MAC
Registers
IEEE 1588
Time Stamp
Switch
Registers
(CSRs)
GPIO/LED
Controller
IEEE 1588
Time Stamp
Clock/Events
System
Interrupt
Controller
System
Clocks/
Reset/PME
Controller
GP Timer
Free-Run
Clk
LAN9312
To optional GPIOs/LEDs
IRQ
Registers
MDIO
TX/RX FIFOs
Register
Access
MUX
System
Registers
(CSRs)
Switch Fabric
Host MAC
Virtual PHY
Host Bus Interface
To 32-bit
Host Bus
EEPROM Loader
EEPROM Controller
I2C (master)
Microwire (master)
I2C/Microwire
To optional
EEPROM
External
25MHz Crystal
Datasheet
SMSC LAN9312
Figure 2.1 Internal LAN9312 Block Diagram
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Frame
Buffers
MII
MDIO
Buffer Manager
Dynamic
QoS
4 Queues
To Ethernet
Port 2
21
DATASHEET
IEEE 1588
Time Stamp
Switch Engine
Search
Engine
MDIO
Registers
10/100
MAC
Port 0
10/100
MAC
Dynamic
QoS
4 Queues
MDIO
Dynamic
QoS
4 Queues
MII
10/100
PHY
Port 1
To Ethernet
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
2.2.1
System Clocks/Reset/PME Controller
A clock module contained within the LAN9312 generates all the system clocks required by the device.
This module interfaces directly with the external 25MHz crystal/oscillator to generate the required clock
divisions for each internal module, with the exception of the 1588 clocks, which are generated in the
1588 Time Stamp Clock/Events module. A 16-bit general purpose timer and 32-bit free-running clock
are provided by this module for general purpose use.
The LAN9312 reset events are categorized as chip-level resets, multi-module resets, and singlemodule resets.
A chip-level reset is initiated by assertion of any of the following input events:

Power-On Reset

nRST Pin Reset
A multi-module reset is initiated by assertion of the following:

Digital Reset - DIGITAL_RST (bit 0) in the Reset Control Register (RESET_CTL)
- Resets all LAN9312 sub-modules except the Ethernet PHYs (Port 1 PHY, Port 2 PHY, and Virtual
PHY)

Soft Reset - SRST (bit 0) in the Hardware Configuration Register (HW_CFG)
- Resets the HBI, Host MAC, and System CSRs below address 100h
A single-module reset is initiated by assertion of the following:

Port 2 PHY Reset - PHY2_RST (bit 2) in the Reset Control Register (RESET_CTL) or Reset (bit
15) in the Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x)
- Resets the Port 2 PHY

Port 1 PHY Reset - PHY1_RST (bit 1) in the Reset Control Register (RESET_CTL) or Reset (bit
15) in the Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x)
- Resets the Port 1 PHY

Virtual PHY Reset - VPHY_RST (bit 0) in the Reset Control Register (RESET_CTL), (bit 10) in
the Power Management Control Register (PMT_CTRL), or Reset (bit 15) in the Virtual PHY Basic
Control Register (VPHY_BASIC_CTRL)
- Resets the Virtual PHY
The LAN9312 supports numerous power management and wakeup features. The Port 1 & 2 PHYs
provide general power-down and energy detect power-down modes, which allow a reduction in PHY
power consumption. The Host MAC provides wake-up frame detection and magic packet detection
modes. The LAN9312 can be programmed to issue an external wake signal (PME) via several
methods, including wake on LAN, wake on link status change (energy detect), and magic packet
wakeup. The PME signal is ideal for triggering system power-up using remote Ethernet wakeup events.
2.2.2
System Interrupt Controller
The LAN9312 provides a multi-tier programmable interrupt structure which is controlled by the System
Interrupt Controller. At the top level are the Interrupt Status Register (INT_STS) and Interrupt Enable
Register (INT_EN). These registers aggregate and control all interrupts from the various LAN9312 submodules. The LAN9312 is capable of generating interrupt events from the following:

1588 Time Stamp

Switch Fabric

Ethernet PHYs

GPIOs

Host MAC (FIFOs, power management)

General Purpose Timer
Revision 2.0 (02-14-13)
22
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet

Software (general purpose)
A dedicated programmable IRQ interrupt output pin is provided for external indication of any LAN9312
interrupts. The IRQ pin is controlled via the Interrupt Configuration Register (IRQ_CFG), which allows
configuration of the IRQ buffer type, polarity, and de-assertion interval.
2.2.3
Switch Fabric
The Switch Fabric consists of the following major function blocks:
2.2.4

10/100 MACs
There is one 10/100 Ethernet MAC per switch fabric port, which provides basic 10/100 Ethernet
functionality, including transmission deferral, collision back-off/retry, TX/RX FCS
checking/generation, TX/RX pause flow control, and transmit back pressure. The 10/100 MACs act
as an interface between the switch engine and the 10/100 PHYs (for ports 1 and 2). The port 0
10/100 MAC interfaces the switch engine to the Host MAC. Each 10/100 MAC includes RX and
TX FIFOs and per port statistic counters.

Switch Engine
This block, consisting of a 3 port VLAN layer 2 switching engine, provides the control for all
forwarding/filtering rules and supports untagged, VLAN tagged, and priority tagged frames. The
switch engine provides an extensive feature set which includes spanning tree protocol support,
multicast packet filtering and Quality of Service (QoS) packet prioritization by VLAN tag, destination
address, and port default value or DIFFSERV/TOS, allowing for a range of prioritization
implementations. A 1K entry forwarding table provides ample room for MAC address forwarding
tables.

Buffer Manager
This block controls the free buffer space, multi-level transmit queues, transmission scheduling, and
packet dropping of the switch fabric. 32K of buffer RAM allows for the storage of multiple packets
while forwarding operations are completed. Each port is allocated 1a cluster of 4 dynamic QoS
queues which allow each queue size to grow and shrink with traffic, effectively utilizing all available
memory. This memory is managed dynamically via the Buffer Manager block.

Switch CSRs
This block contains all switch related control and status registers, and allows all aspects of the
switch fabric to be managed. These registers are indirectly accessible via the memory mapped
system control and status registers
Ethernet PHYs
The LAN9312 contains three PHYs: Port 1 PHY, Port 2 PHY and a Virtual PHY. The Port 1 & 2 PHYs
are identical in functionality and each connect their corresponding Ethernet signal pins to the switch
fabric MAC of their respective port. These PHYs interface with their respective MAC via an internal MII
interface. The Virtual PHY provides the virtual functionality of a PHY and allows connection of the Host
MAC to port 0 of the switch fabric as if it was connected to a single port PHY. All PHYs comply with
the IEEE 802.3 Physical Layer for Twisted Pair Ethernet and can be configured for full/half duplex 100
Mbps (100BASE-TX) or 10Mbps (10BASE-T) Ethernet operation. All PHY registers follow the IEEE
802.3 (clause 22.2.4) specified MII management register set.
2.2.5
Host Bus Interface (HBI)
The Host Bus Interface (HBI) module provides a high-speed asynchronous SRAM-like slave interface
that facilitates communication between the LAN9312 and a host system. The HBI allows access to the
System CSRs and handles byte swapping based on the dynamic endianess select. The HBI interfaces
to the switch fabric via the Host MAC, which contains the TX/RX Data and Status FIFOs, Host MAC
registers and power management features. The main features of the HBI are:

SMSC LAN9312
Asynchronous 32-bit Host Bus Interface
- Host Data Bus Endianess Control
- Direct FIFO Access Modes
23
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
2.2.6

System CSRs Access

Interrupt Support
Host MAC
The Host MAC incorporates the essential protocol requirements for operating an Ethernet/IEEE 802.3compliant node and provides an interface between the Host Bus Interface (HBI) and the Ethernet PHYs
and Switch Fabric. On the front end, the Host MAC interfaces to the HBI via 2 sets of FIFO’s (TX Data
FIFO, TX Status FIFO, RX Data FIFO, RX Status FIFO). The FIFOs are a conduit between the HBI
and the Host MAC through which all transmitted and received data and status information is passed.
An additional bus is used to access the Host MAC CSR’s via the Host MAC CSR Interface Command
Register (MAC_CSR_CMD) and Host MAC CSR Interface Data Register (MAC_CSR_DATA) system
registers.
On the back end, the Host MAC interfaces with the 10/100 Ethernet PHY’s (Virtual PHY, Port 1 PHY,
Port 2 PHY) via an internal SMI (Serial Management Interface) bus. This allows the Host MAC access
to the PHY’s internal registers via the Host MAC MII Access Register (HMAC_MII_ACC) and Host
MAC MII Data Register (HMAC_MII_DATA). The Host MAC interfaces to the Switch Engine Port 0 via
an internal MII (Media Independent Interface) connection allowing for incoming and outgoing Ethernet
packet transfers.
The Host MAC can operate at either 100Mbps or 10Mbps in both half-duplex or full-duplex modes.
When operating in half-duplex mode, the Host MAC complies fully with Section 4 of ISO/IEC 8802-3
(ANSI/IEEE standard) and ANSI/IEEE 802.3 standards. When operating in full-duplex mode, the Host
MAC complies with IEEE 802.3 full-duplex operation standard.
2.2.7
EEPROM Controller/Loader
The EEPROM Controller is an I2C/Microwire master module which interfaces an optional external
EEPROM with the system register bus and the EEPROM Loader. Multiple types (I2C/Microwire) and
sizes of external EEPROMs are supported. Configuration of the EEPROM type and size are
accomplished via the eeprom_type_strap and eeprom_size_strap[1:0] configuration straps respectively.
Various commands are supported for each EEPROM type, allowing for the storage and retrieval of
static data. The I2C interface conforms to the Philips I2C-Bus Specification.
The EEPROM Loader module interfaces to the EEPROM Controller, Ethernet PHYs, and the system
CSRs. The EEPROM Loader provides the automatic loading of configuration settings from the
EEPROM into the LAN9312 at reset. The EEPROM Loader runs upon a pin reset (nRST), power-on
reset (POR), digital reset (DIGITAL_RST bit in the Reset Control Register (RESET_CTL)), or upon the
issuance of a RELOAD command via the EEPROM Command Register (E2P_CMD).
2.2.8
1588 Time Stamp
The IEEE 1588 Time Stamp modules provide hardware support for the IEEE 1588 Precision Time
Protocol (PTP), allowing clock synchronization with remote Ethernet devices, packet time stamping,
and time driven event generation. Time stamping is supported on all ports, with an individual IEEE
1588 Time Stamp module connected to each port via the MII bus. Any port may function as a master
or a slave clock per the IEEE 1588 specification, and the LAN9312 as a whole may function as a
boundary clock.
A 64-bit tunable clock is provided that is used as the time source for all IEEE 1588 time stamp related
functions. The IEEE 1588 Clock/Events block provides IEEE 1588 clock comparison based interrupt
generation and time stamp related GPIO event generation. Two LAN9312 GPIO pins (GPIO[8:9]) can
be used to trigger a time stamp capture when configured as an input, or output a signal from the GPIO
based on an IEEE 1588 clock target compare event when configured as an output. All features of the
IEEE 1588 hardware time stamp unit can be monitored and configured via their respective IEEE 1588
configuration and status registers (CSRs).
Revision 2.0 (02-14-13)
24
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
2.2.9
GPIO/LED Controller
The LAN9312 provides 12 configurable general-purpose input/output pins which are controlled via this
module. These pins can be individually configured via the GPIO/LED CSRs to function as inputs, pushpull outputs, or open drain outputs and each is capable of interrupt generation with configurable
polarity. Two of the GPIO pins (GPIO[9:8]) can be used for IEEE 1588 timestamp functions, allowing
GPIO driven 1588 time clock capture when configured as an input, or GPIO output generation based
on an IEEE 1588 clock target compare event.
In addition, 8 of the GPIO pins can be alternatively configured as LED outputs. These pins, GPIO[7:0]
(nP1LED[3:0] and nP2LED[3:0]), may be enabled to drive Ethernet status LEDs for external indication
of various attributes of the switch ports.
2.3
System Configuration
In a typical application, the LAN9312 Host Bus Interface (HBI) is connected to the host
microprocessor/microcontroller via the asynchronous 32-bit interface, allowing access to the LAN9312
system configuration and status registers. The LAN9312 utilizes the internal Host MAC to provide a
network path for the host CPU. The LAN9312 may share the host bus with additional system memory
and/or peripherals. For more information on the HBI, refer to Chapter 8, "Host Bus Interface (HBI)," on
page 99.
The 2 Ethernet ports of the LAN9312 must be connected to Auto-MDIX style magnetics for proper
operation on the Ethernet network. Refer to the SMSC Application Note 8.13 “Suggested Magnetics”
for further details.
The LAN9312 also supports optional EEPROM and GPIOs/LEDs. When an EEPROM is connected,
the EEPROM loader can be used to load the initial device configuration from the external EEPROM
via the I2C/Microwire interface.
A system configuration diagram of the LAN9312 in a typical embedded environment can be seen in
Figure 2.2.
To Ethernet
I2C/Microwire
Magnetics
EEPROM
(optional)
Microprocessor/
Microcontroller
LAN9312
To Ethernet
Magnetics
System
Memory
GPIOs/LEDs
(optional)
External
25MHz Crystal
System
Peripherals
Figure 2.2 System Block Diagram
SMSC LAN9312
25
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 3 Pin Description and Configuration
VSS
97
EEDO/EEPROM_TYPE
98
EECLK/EE_SCL/
EEPROM_SIZE_1
99
NC
NC
VDD33IO
nP1LED0/GPIO0
nP1LED1/GPIO1
nP1LED2/GPIO2
nP1LED3/GPIO3
VDD18CORE
VDD33IO
nP2LED0/GPIO4
nP2LED1/GPIO5
nP2LED2/GPIO6
nP2LED3/GPIO7
GPIO8
VDD33IO
VSS
GPIO9
GPIO10
GPIO11
NC
TEST1
VDD18CORE
VDD33IO
VDD33IO
nRST
AUTO_MDIX_2
AUTO_MDIX_1
PHY_ADDR_SEL
LED_EN
VDD33IO
VDD18CORE
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
128-VTQFP Pin Diagram
EEDI/EE_SDA
3.1.1
95
Pin Diagrams
96
3.1
64
VDD33IO
SMSC
LAN9312
128-VTQFP
63
IRQ
62
PME
61
END_SEL
60
FIFO_SEL
59
nCS
TOP VIEW
58
nWR
39
VDD33IO
RXP2
123
38
D4
RXN2
124
37
D5
VDD33A2
125
36
D6
TXP2
126
35
D7
TXN2
127
34
D8
VSS
128
33
VDD33IO
32
122
D9
VDD18CORE
VDD33A2
31
40
D10
121
30
D3
VDD18TX2
D11
41
29
120
D12
D2
VDD33BIAS
28
42
D13
119
27
D1
EXRES
VDD33IO
43
26
118
D14
D0
VDD18TX1
25
44
D15
117
24
A9
VDD33A1
D16
45
23
116
D17
VDD33IO
RXP1
22
46
D18
115
21
A8
RXN1
VDD33IO
47
20
114
D19
VSS
VDD33A1
19
48
D20
113
18
A7
VSS
VSS
49
17
112
D21
A6
VSS
16
50
D22
111
15
A5
TXP1
D23
51
14
110
VDD18CORE
A4
TXN1
13
52
VDD33IO
109
12
A3
NC
D24
53
11
108
D25
VDD33IO
TEST2
10
54
D26
107
9
A2
VDD18PLL
D27
55
8
106
D28
NC
XO
7
56
VDD33IO
105
6
nRD
XI
D29
57
5
104
D30
VDD18CORE
4
103
D31
NC
3
102
VDD18CORE
NC
2
101
1
EECS/EEPROM_SIZE_0
NC
100
NC
VDD33IO
Figure 3.1 LAN9312 128-VTQFP Pin Assignments (TOP VIEW)
Revision 2.0 (02-14-13)
26
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
VSS
97
EEDO/EEPROM_TYPE
98
EECLK/EE_SCL/
EEPROM_SIZE_1
99
EEDI/EE_SDA
NC
NC
VDD33IO
nP1LED0/GPIO0
nP1LED1/GPIO1
nP1LED2/GPIO2
nP1LED3/GPIO3
VDD18CORE
VDD33IO
nP2LED0/GPIO4
nP2LED1/GPIO5
nP2LED2/GPIO6
nP2LED3/GPIO7
GPIO8
VDD33IO
VSS
GPIO9
GPIO10
GPIO11
NC
TEST1
VDD18CORE
VDD33IO
VDD33IO
nRST
AUTO_MDIX_2
AUTO_MDIX_1
PHY_ADDR_SEL
LED_EN
VDD33IO
VDD18CORE
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
128-XVTQFP Pin Diagram
96
3.1.2
64
VDD33IO
SMSC
LAN9312
128-XVTQFP
63
IRQ
62
PME
61
END_SEL
60
FIFO_SEL
59
nCS
TOP VIEW
58
nWR
VDD33IO
100
EECS/EEPROM_SIZE_0
101
NC
102
NC
103
VDD18CORE
104
57
nRD
XI
105
56
NC
XO
106
55
A2
VDD18PLL
107
54
VDD33IO
TEST2
108
53
A3
NC
109
52
A4
TXN1
110
51
A5
TXP1
111
50
A6
VSS
112
49
A7
VSS
113
48
VSS
VDD33A1
114
47
A8
RXN1
115
46
VDD33IO
RXP1
116
45
A9
VDD33A1
117
44
D0
VDD18TX1
118
43
D1
EXRES
119
42
D2
VDD33BIAS
120
41
D3
VDD18TX2
121
40
VDD18CORE
VDD33A2
122
39
VDD33IO
RXP2
123
38
D4
RXN2
124
37
D5
VDD33A2
125
36
D6
TXP2
126
35
D7
TXN2
127
34
D8
VSS
128
33
VDD33IO
20
21
22
23
24
25
26
27
28
29
30
31
D19
VDD33IO
D18
D17
D16
D15
D14
VDD33IO
D13
D12
D11
D10
32
19
D20
D9
18
12
D24
VSS
11
D25
17
10
D26
D21
9
D27
16
8
D28
D22
7
VDD33IO
15
6
D29
D23
5
D30
14
4
D31
VDD18CORE
3
VDD18CORE
13
2
NC
VDD33IO
1
NC
VSS
NOTE: EXPOSED PAD ON BOTTOM OF PACKAGE MUST BE CONNECTED TO GROUND
Figure 3.2 LAN9312 128-XVTQFP Pin Assignments (TOP VIEW)
SMSC LAN9312
27
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
3.2
Pin Descriptions
This section contains the descriptions of the LAN9312 pins. The pin descriptions have been broken
into functional groups as follows:

LAN Port 1 Pins

LAN Port 2 Pins

LAN Port 1 & 2 Power and Common Pins

Host Bus Interface Pins

EEPROM Pins

Dedicated Configuration Strap Pins

Miscellaneous Pins

PLL Pins

Core and I/O Power and Ground Pins

No-Connect Pins
Note: A list of buffer type definitions is provided in Section 1.2, "Buffer Types," on page 18.
Table 3.1 LAN Port 1 Pins
PIN
89-92
NAME
SYMBOL
BUFFER
TYPE
Port 1 LED
Indicators
nP1LED[3:0]
OD12
LED Indicators: When configured as LED outputs
via the LED Configuration Register (LED_CFG),
these pins are open-drain, active low outputs and
the pull-ups and input buffers are disabled. The
functionality of each pin is determined via the
LED_CFG[9:8] bits.
General
Purpose I/O
Data
GPIO[3:0]
IS/O12/
OD12
(PU)
General Purpose I/O Data: When configured as
GPIO via the LED Configuration Register
(LED_CFG), these general purpose signals are
fully programmable as either push-pull outputs,
open-drain outputs or Schmitt-triggered inputs by
writing the General Purpose I/O Configuration
Register (GPIO_CFG) and General Purpose I/O
Data & Direction Register (GPIO_DATA_DIR). The
pull-ups are enabled in GPIO mode. The input
buffers are disabled when set as an output.
DESCRIPTION
Note:
See Chapter 13, "GPIO/LED Controller,"
on page 162 for additional details.
110
Port 1
Ethernet TX
Negative
TXN1
AIO
Ethernet TX Negative: Negative output of Port 1
Ethernet transmitter. See Note 3.1 for additional
information.
111
Port 1
Ethernet TX
Positive
TXP1
AIO
Ethernet TX Positive: Positive output of Port 1
Ethernet transmitter. See Note 3.1 for additional
information.
115
Port 1
Ethernet RX
Negative
RXN1
AIO
Ethernet RX Negative: Negative input of Port 1
Ethernet receiver. See Note 3.1 for additional
information.
116
Port 1
Ethernet RX
Positive
RXP1
AIO
Ethernet RX Positive: Positive input of Port 1
Ethernet receiver. See Note 3.1 for additional
information.
Revision 2.0 (02-14-13)
28
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Note 3.1
The pin names for the twisted pair pins apply to a normal connection. If HP Auto-MDIX is
enabled and a reverse connection is detected or manually selected, the RX and TX pins
will be swapped internally.
Table 3.2 LAN Port 2 Pins
PIN
83-86
NAME
SYMBOL
BUFFER
TYPE
Port 2 LED
Indicators
nP2LED[3:0]
OD12
LED indicators: When configured as LED outputs
via the LED Configuration Register (LED_CFG),
these pins are open-drain, active low outputs and
the pull-ups and input buffers are disabled. The
functionality of each pin is determined via the
LED_CFG[9:8] bits.
General
Purpose I/O
Data
GPIO[7:4]
IS/O12/
OD12
(PU)
General Purpose I/O Data: When configured as
GPIO via the LED Configuration Register
(LED_CFG), these general purpose signals are
fully programmable as either push-pull outputs,
open-drain outputs or Schmitt-triggered inputs by
writing the General Purpose I/O Configuration
Register (GPIO_CFG) and General Purpose I/O
Data & Direction Register (GPIO_DATA_DIR). The
pull-ups are enabled in GPIO mode. The input
buffers are disabled when set as an output.
DESCRIPTION
Note:
See Chapter 13, "GPIO/LED Controller,"
on page 162 for additional details.
127
Port 2
Ethernet TX
Negative
TXN2
AIO
Ethernet TX Negative: Negative output of Port 2
Ethernet transmitter. See Note 3.2 for additional
information.
126
Port 2
Ethernet TX
Positive
TXP2
AIO
Ethernet TX Positive: Positive output of Port 2
Ethernet transmitter. See Note 3.2 for additional
information.
124
Port 2
Ethernet RX
Negative
RXN2
AIO
Ethernet RX Negative: Negative input of Port 2
Ethernet receiver. See Note 3.2 for additional
information.
123
Port 2
Ethernet RX
Positive
RXP2
AIO
Ethernet RX Positive: Positive input of Port 2
Ethernet receiver. See Note 3.2 for additional
information.
Note 3.2
The pin names for the twisted pair pins apply to a normal connection. If HP Auto-MDIX is
enabled and a reverse connection is detected or manually selected, the RX and TX pins
will be swapped internally.
Table 3.3 LAN Port 1 & 2 Power and Common Pins
PIN
NAME
SYMBOL
BUFFER
TYPE
119
Bias
Reference
EXRES
AI
Bias Reference: Used for internal bias circuits.
Connect to an external 12.4K ohm, 1% resistor to
ground.
VDD33A1
P
+3.3V Port 1 Analog Power Supply
114,117
+3.3V Port 1
Analog Power
Supply
SMSC LAN9312
DESCRIPTION
Refer to the LAN9312 reference schematic for
additional connection information.
29
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 3.3 LAN Port 1 & 2 Power and Common Pins (continued)
PIN
NAME
SYMBOL
BUFFER
TYPE
VDD33A2
P
122,125
+3.3V Port 2
Analog Power
Supply
VDD33BIAS
120
+3.3V Master
Bias Power
Supply
VDD18TX2
121
Port 2
Transmitter
+1.8V Power
Supply
DESCRIPTION
+3.3V Port 2 Analog Power Supply
Refer to the LAN9312 reference schematic for
additional connection information.
P
+3.3V Master Bias Power Supply
Refer to the LAN9312 reference schematic for
additional connection information.
P
Port 2 Transmitter +1.8V Power Supply: This pin
is supplied from the internal PHY voltage regulator.
This pin must be tied to the VDD18TX1 pin for
proper operation.
Refer to the LAN9312 reference schematic for
additional connection information.
118
Port 1
Transmitter
+1.8V Power
Supply
VDD18TX1
P
Port 1 Transmitter +1.8V Power Supply: This pin
must be connected directly to the VDD18TX2 pin
for proper operation.
Refer to the LAN9312 reference schematic for
additional connection information.
Table 3.4 Host Bus Interface Pins
PIN
NAME
SYMBOL
BUFFER
TYPE
4-6,
8-12,
15-17,19,
20,22-26,
28-32,
34-38,
41-44
Host Bus
Data
D[31:0]
IS/O8
45,47,
49-53,
55
57
58
59
DESCRIPTION
Host Bus Data High: Bits 31-0 of the Host Bus 32bit data port.
Note:
Host Bus
Address
A[9:2]
IS
Big and little endianess is supported.
Host Bus Address: 9-bit Host Bus Address Port
used to select Internal CSR’s and TX and RX
FIFO’s.
Note:
The A0 and A1 bits are not used because
the LAN9312 must be accessed on
DWORD boundaries.
Read Strobe
nRD
IS
Read Strobe: Active low strobe to indicate a read
cycle. This signal is qualified by the nCS chip
select.
Write Strobe
nWR
IS
Write Strobe: Active low strobe to indicate a write
cycle. This signal is qualified by the nCS chip
select.
Chip Select
nCS
IS
Chip Select: Active low signal used to qualify read
and write operations.
Revision 2.0 (02-14-13)
30
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 3.4 Host Bus Interface Pins (continued)
PIN
60
NAME
SYMBOL
BUFFER
TYPE
Data FIFO
Direct Access
Select
FIFO_SEL
IS
Data FIFO Direct Access Select: When driven
high, all accesses to the LAN9312 are directed to
the RX and TX Data FIFO’s. All reads are from the
RX Data FIFO, and all writes are to the TX Data
FIFO. In this mode, the address input is ignored.
Refer to Section 14.1.3, "Direct FIFO Access
Mode," on page 167 for additional information.
Endianess
Select
END_SEL
IS
Endianess Select: When this signal is set high,
big endian mode is selected. When low, little
endian mode is selected. This signal may be
dynamically changed or held static. Refer to
Chapter 8, "Host Bus Interface (HBI)," on page 99
for additional information.
61
DESCRIPTION
Note: Refer to Chapter 8, "Host Bus Interface (HBI)," on page 99 for additional information regarding
the use of these signals.
Table 3.5 EEPROM Pins
PIN
96
BUFFER
TYPE
NAME
SYMBOL
DESCRIPTION
EEPROM
Microwire
Data Input
EEDI
IS
(PD)
EEPROM Microwire Data Input (EEDI): In
Microwire EEPROM mode (EEPROM_TYPE = 0),
this pin is the Microwire EEPROM serial data input.
EEPROM I2C
Serial Data
Input/Output
EE_SDA
IS/OD8
EEPROM I2C Serial Data Input/Output
(EE_SDA): In I2C EEPROM mode
(EEPROM_TYPE = 1), this pin is the I2C EEPROM
serial data input/output.
Note:
EEPROM
Microwire
Data Output
EEDO
O8
EEPROM Microwire Data Output: In Microwire
EEPROM mode (EEPROM_TYPE = 0), this pin is
the Microwire EEPROM serial data output.
Note:
In I2C mode (EEPROM_TYPE=1), this pin
is not used and is driven low.
Note:
When not using a Microwire or I2C
EEPROM, an external pull-down resistor
is recommended on this pin.
98
EEPROM
Type Strap
EEPROM_TYPE
IS
Note 3.3
EEPROM Type Strap: Configures the EEPROM
type. See Note 3.4
0 = Microwire Mode
1 = I2C Mode
Note:
SMSC LAN9312
31
If I2C is selected, an external pull-up is
required when using an EEPROM and is
recommended if no EEPROM is attached.
DATASHEET
When not using a Microwire or I2C
EEPROM, an external pull-down resistor
is recommended on this pin.
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 3.5 EEPROM Pins (continued)
PIN
NAME
SYMBOL
BUFFER
TYPE
EEPROM
Microwire
Serial Clock
EECLK
O8
EEPROM I2C
Serial Clock
EE_SCL
IS/OD8
DESCRIPTION
EEPROM Microwire Serial Clock (EECLK): In
Microwire EEPROM mode (EEPROM_TYPE = 0),
this pin is the Microwire EEPROM clock output.
EEPROM I2C Serial Clock (EE_SCL): In I2C
EEPROM mode (EEPROM_TYPE=1), this pin is
the I2C EEPROM clock input/open-drain output.
Note:
99
EEPROM
Size Strap 1
EEPROM_SIZE_1
EEPROM
Microwire
Chip Select
EECS
IS
Note 3.5
O8
EEPROM Size Strap 1: Configures the high bit of
the EEPROM size range as specified in Section
10.2, "I2C/Microwire Master EEPROM Controller,"
on page 137. This bit is not used for I2C
EEPROMs. See Note 3.4.
EEPROM Microwire Chip Select: In Microwire
EEPROM mode (EEPROM_TYPE = 0), this pin is
the Microwire EEPROM chip select output.
Note:
101
EEPROM
Size Strap 0
EEPROM_SIZE_0
IS
Note 3.3
If I2C is selected, an external pull-up is
required when using an EEPROM and is
recommended if no EEPROM is attached.
In I2C mode (EEPROM_TYPE=1), this pin
is not used and is driven low.
EEPROM Size Strap 0: Configures the low bit of
the EEPROM size range as specified in Section
10.2, "I2C/Microwire Master EEPROM Controller,"
on page 137. See Note 3.4.
Note 3.3
The IS buffer type is valid only during the time specified in Section 15.5.2, "Reset and
Configuration Strap Timing," on page 445.
Note 3.4
Configuration strap values are latched on power-on reset or nRST de-assertion.
Configuration strap pins are identified by an underlined symbol name. Refer to Section
4.2.4, "Configuration Straps," on page 40 for more information.
Note 3.5
The IS buffer type is valid only during the time specified in Section 15.5.2, "Reset and
Configuration Strap Timing," on page 445 and when in I2C mode.
Revision 2.0 (02-14-13)
32
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 3.6 Dedicated Configuration Strap Pins
BUFFER
TYPE
LED_EN
IS
(PU)
LED Enable Strap: Configures the default value
for the LED_EN bits in the LED Configuration
Register (LED_CFG). When latched low, all 8
LED/GPIO pins are configured as GPIOs. When
latched high, all 8 LED/GPIO pins are configured
as LEDs. See Note 3.6.
PHY Address
Strap
PHY_ADDR_SEL
IS
(PU)
PHY Address Select Strap: Configures the default
MII management address values for the PHYs
(Virtual, Port 1, and Port 2) as detailed in Section
7.1.1, "PHY Addressing," on page 82.
68
PORT 2 PHY
ADDRESS
LED Enable
Strap
67
DESCRIPTION
PORT 1 PHY
ADDRESS
SYMBOL
VIRTUAL PHY
ADDRESS
NAME
PHY_ADDR_SEL
VALUE
PIN
0
0
1
2
1
1
2
3
See Note 3.6.
Port 1 AutoMDIX Enable
Strap
69
AUTO_MDIX_1
IS
(PU)
Port 1 Auto-MDIX Enable Strap: Configures the
Auto-MDIX functionality on Port 1. When latched
low, Auto-MDIX is disabled. When latched high,
Auto-MDIX is enabled.
See Note 3.6.
Port 2 AutoMDIX Enable
Strap
70
AUTO_MDIX_2
IS
(PU)
Port 2 Auto-MDIX Enable Strap: Configures the
Auto-MDIX functionality on Port 2. When latched
low, Auto-MDIX is disabled. When latched high,
Auto-MDIX is enabled.
See Note 3.6.
Note: For more information on configuration straps, refer to Section 4.2.4, "Configuration Straps," on
page 40. Additional strap pins, which share functionality with the EEPROM pins, are described
in Table 3.5.
Note 3.6
SMSC LAN9312
Configuration strap values are latched on power-on reset or nRST de-assertion.
Configuration strap pins are identified by an underlined symbol name. Some configuration
straps can be overridden by values from the EEPROM Loader. Refer to Section 4.2.4,
"Configuration Straps," on page 40 for more information.
33
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 3.7 Miscellaneous Pins
PIN
NAME
SYMBOL
General
Purpose I/O
Data
GPIO[11:8]
BUFFER
TYPE
IS/OD12/
O12
(PU)
Note 3.7
77-79,
82
DESCRIPTION
General Purpose I/O Data: These general
purpose signals are fully programmable as either
push-pull outputs, open-drain outputs, or Schmitttriggered inputs by writing the General Purpose I/O
Configuration Register (GPIO_CFG) and General
Purpose I/O Data & Direction Register
(GPIO_DATA_DIR). For more information, refer to
Chapter 13, "GPIO/LED Controller," on page 162.
Note:
63
Interrupt
Output
IRQ
O8/OD8
Interrupt Output: Interrupt request output. The
polarity, source and buffer type of this signal is
programmable via the Interrupt Configuration
Register (IRQ_CFG). For more information, refer to
Chapter 5, "System Interrupts," on page 49.
System Reset
Input
nRST
IS
(PU)
System Reset Input: This active low signal allows
external hardware to reset the LAN9312. The
LAN9312 also contains an internal power-on reset
circuit. Thus, this signal may be left unconnected if
an external hardware reset is not needed. When
used, this signal must adhere to the reset timing
requirements as detailed in Section 15.5.2, "Reset
and Configuration Strap Timing," on page 445.
71
Note:
75
108
The remaining GPIO[7:0] pins share
functionality with the LED output pins, as
described in Table 3.1 and Table 3.2.
The LAN9312 must always be read at
least once after power-up or reset to
ensure that write operations function
properly.
Test 1
TEST1
AI
Test 1: This pin must be tied to VDD33IO for
proper operation.
Test 2
TEST2
AI
Test 2: This pin must be tied to VDD33IO for
proper operation.
Power
Management
Event
PME
O8/OD8
62
Power Management Event: When programmed
accordingly, this signal is asserted upon detection
of a wakeup event. The polarity and buffer type of
this signal is programmable via the PME_EN bit of
the Power Management Control Register
(PMT_CTRL).
Refer to Chapter 4, "Clocking, Resets, and Power
Management," on page 36 for additional
information on the LAN9312 power management
features.
Note 3.7
Revision 2.0 (02-14-13)
The input buffers are enabled when configured as GPIO inputs only.
34
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 3.8 PLL Pins
PIN
107
NAME
SYMBOL
BUFFER
TYPE
PLL +1.8V
Power Supply
VDD18PLL
P
DESCRIPTION
PLL +1.8V Power Supply: This pin must be
connected to VDD18CORE for proper operation.
Refer to the LAN9312 reference schematic for
additional connection information.
Crystal Input
XI
ICLK
Crystal Input: External 25MHz crystal input. This
signal can also be driven by a single-ended clock
oscillator. When this method is used, XO should be
left unconnected.
Crystal
Output
XO
OCLK
Crystal Output: External 25MHz crystal output.
105
106
Table 3.9 Core and I/O Power and Ground Pins
PIN
NAME
SYMBOL
BUFFER
TYPE
7,13,21,27,
33,39,46,
54,64,66,
72,73,81,
87,93,100
+3.3V I/O
Power
VDD33IO
P
DESCRIPTION
+3.3V Power Supply for I/O Pins and Internal
Regulator
Refer to the LAN9312 reference schematic for
additional connection information.
Digital Core
+1.8V Power
Supply
Output
3,14,40,65,
74,88,104
VDD18CORE
P
Digital Core +1.8V Power Supply Output: +1.8V
power from the internal core voltage regulator. All
VDD18CORE pins must be tied together for proper
operation.
Refer to the LAN9312 reference schematic for
additional connection information.
18,48,80,
97,112,113,
128
Common
Ground
VSS
P
Common Ground
Note 3.8
Note 3.8
Plus external pad for 128-XVTQFP package only
Table 3.10 No-Connect Pins
PIN
NAME
SYMBOL
BUFFER
TYPE
1,2,56,
76,94,95,
102,103,
109
No Connect
NC
-
SMSC LAN9312
DESCRIPTION
No Connect: These pins must be left floating for
normal device operation.
35
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 4 Clocking, Resets, and Power Management
4.1
Clocks
The LAN9312 includes a clock module which provides generation of all system clocks as required by
the various sub-modules of the device. The LAN9312 requires a fixed-frequency 25MHz clock source
for use by the internal clock oscillator and PLL. This is typically provided by attaching a 25MHz crystal
to the XI and XO pins as specified in Section 15.6, "Clock Circuit," on page 454. Optionally, this clock
can be provided by driving the XI input pin with a single-ended 25MHz clock source. If a single-ended
source is selected, the clock input must run continuously for normal device operation. The internal PLL
generates a fixed 200MHz base clock which is used to derive all LAN9312 sub-system clocks.
In addition to the sub-system clocks, the clock module is also responsible for generating the clocks
used for the general purpose timer and free-running clock. Refer to Chapter 12, "General Purpose
Timer & Free-Running Clock," on page 161 for additional details.
Note: Crystal specifications are provided in Table 15.15, “LAN9312Crystal Specifications,” on
page 454.
4.2
Resets
The LAN9312 provides multiple hardware and software reset sources, which allow varying levels of
the LAN9312 to be reset. All resets can be categorized into three reset types as described in the
following sections:

Chip-Level Resets
—Power-On Reset (POR)
—nRST Pin Reset

Multi-Module Resets
—Digital Reset (DIGITAL_RST)
—Soft Reset (SRST)

Single-Module Resets
—Port 2 PHY Reset
—Port 1 PHY Reset
—Virtual PHY Reset
The LAN9312 supports the use of configuration straps to allow automatic custom configurations of
various LAN9312 parameters. These configuration strap values are set upon de-assertion of all chiplevel resets and can be used to easily set the default parameters of the chip at power-on or pin (nRST)
reset. Refer to Section 4.2.4, "Configuration Straps," on page 40 for detailed information on the usage
of these straps.
Note: The LAN9312 EEPROM Loader is run upon a power-on reset, nRST pin reset, and digital
reset. Refer to Section 10.2.4, "EEPROM Loader," on page 149 for additional information.
Table 4.1 summarizes the effect of the various reset sources on the LAN9312. Refer to the following
sections for detailed information on each of these reset types.
Revision 2.0 (02-14-13)
36
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
SYSTEM
CLOCKS/RESET/PME
SYS INTERRUPTS
SWITCH FABRIC
ETHERNET PHYS
HBI
HOST MAC
EEPROM
CONTROLLER
1588 TIME STAMP
GPIO/LED
CONTROLLER
CONFIG. STRAPS
LATCHED
EEPROM LOADER
RUN
Table 4.1 Reset Sources and Affected LAN9312 Circuitry
POR
X
X
X
X
X
X
X
X
X
X
X
nRST Pin
X
X
X
X
X
X
X
X
X
X
X
Digital Reset
X
X
X
X
X
X
X
X
X
X
RESET SOURCE
Soft Reset
Port 2 PHY
X
Port 1 PHY
X
Virtual PHY
X
Note 4.1
4.2.1
X
Note 4.1
In the case of a soft reset, the EEPROM Loader is run, but loads only the MAC address
into the Host MAC. No other values are loaded by the EEPROM Loader in this case.
Chip-Level Resets
A chip-level reset event activates all internal resets, effectively resetting the entire LAN9312.
Configuration straps are latched, and the EEPROM Loader is run as a result of chip-level resets. A
chip-level reset is initiated by assertion of any of the following input events:

Power-On Reset (POR)

nRST Pin Reset
Chip-level reset completion/configuration can be determined by polling the READY bit of the Hardware
Configuration Register (HW_CFG) or Power Management Control Register (PMT_CTRL) until it is set.
When set, the READY bit indicates that the reset has completed and the device is ready to be
accessed.
With the exception of the Hardware Configuration Register (HW_CFG), Power Management Control
Register (PMT_CTRL), Byte Order Test Register (BYTE_TEST), and Reset Control Register
(RESET_CTL), read access to any internal resources is forbidden while the READY bit is cleared.
Writes to any address are invalid until the READY bit is set.
Note: The LAN9312 must be read at least once after any chip-level reset to ensure that write
operations function properly.
SMSC LAN9312
37
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
4.2.1.1
Power-On Reset (POR)
A power-on reset occurs whenever power is initially applied to the LAN9312, or if the power is removed
and reapplied to the LAN9312. This event resets all circuitry within the device. Configuration straps
are latched, and the EEPROM Loader is run as a result of this reset.
A POR reset typically takes approximately 23mS, plus additional time (91uS for I2C, 28uS for
Microwire) per byte of data loaded from the EEPROM via the EEPROM Loader. A full EEPROM load
(64KB for I2C, 2KB for Microwire) will complete in approximately 6.0 seconds for I2C EEPROM, and
80mS for Microwire EEPROM.
4.2.1.2
nRST Pin Reset
Driving the nRST input pin low initiates a chip-level reset. This event resets all circuitry within the
device. Use of this reset input is optional, but when used, it must be driven for the period of time
specified in Section 15.5.2, "Reset and Configuration Strap Timing," on page 445. Configuration straps
are latched, and the EEPROM Loader is run as a result of this reset.
A nRST pin reset typically takes approximately 760uS, plus additional time (91uS for I2C, 28uS for
Microwire) per byte of data loaded from the EEPROM via the EEPROM Loader. A full EEPROM load
(64KB for I2C, 2KB for Microwire) will complete in approximately 6.0 seconds for I2C EEPROM, and
58mS for Microwire EEPROM.
Note: The nRST pin is pulled-high internally. If unused, this signal can be left unconnected. Do not
rely on internal pull-up resistors to drive signals external to the device.
Please refer to Section Table 3.7, "Miscellaneous Pins," on page 34 for a description of the nRST pin.
4.2.2
Multi-Module Resets
Multi-module resets activate multiple internal resets, but do not reset the entire chip. Configuration
straps are not latched upon multi-module resets. A multi-module reset is initiated by assertion of the
following:

Digital Reset (DIGITAL_RST)

Soft Reset (SRST)
Chip-level reset completion/configuration can be determined by polling the READY bit of the Hardware
Configuration Register (HW_CFG) or Power Management Control Register (PMT_CTRL) until it is set.
When set, the READY bit indicates that the reset has completed and the device is ready to be
accessed.
With the exception of the Hardware Configuration Register (HW_CFG), Power Management Control
Register (PMT_CTRL), Byte Order Test Register (BYTE_TEST), and Reset Control Register
(RESET_CTL), read access to any internal resources is forbidden while the READY bit is cleared.
Writes to any address are invalid until the READY bit is set.
Note: The digital reset and soft reset do not reset register bits designated as NASR.
Note: The LAN9312 must be read at least once after a multi-module reset to ensure that write
operations function properly.
4.2.2.1
Digital Reset (DIGITAL_RST)
A digital reset is performed by setting the DIGITAL_RST bit of the Reset Control Register
(RESET_CTL). A digital reset will reset all LAN9312 sub-modules except the Ethernet PHYs (Port 1
PHY, Port 2 PHY, and Virtual PHY). The EEPROM Loader will automatically run following this reset.
Configuration straps are not latched as a result of a digital reset.
A digital reset typically takes approximately 760uS, plus additional time (91uS for I2C, 28uS for
Microwire) per byte of data loaded from the EEPROM via the EEPROM Loader. A full EEPROM load
Revision 2.0 (02-14-13)
38
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
(64KB for I2C, 2KB for Microwire) will complete in approximately 6.0 seconds for I2C EEPROM, and
58mS for Microwire EEPROM.
4.2.2.2
Soft Reset (SRST)
A soft reset is performed by setting the SRST bit of the Hardware Configuration Register (HW_CFG).
A soft reset will reset the HBI, Host MAC, and System CSRs below address 100h. The soft reset also
clears any TX or RX errors in the Host MAC transmitter and receiver (TXE/RXE). This reset does not
latch the configuration straps. On soft reset, the EEPROM Loader is run, but loads only the MAC
address into the Host MAC. No other values are loaded by the EEPROM Loader in this case.
A soft reset typically takes 590uS, plus an additional time (550uS for I2C, 170uS for Microwire) when
data is loaded from the EEPROM via the EEPROM Loader.
4.2.3
Single-Module Resets
A single-module reset will reset only the specified module. Single-module resets do not latch the
configuration straps or initiate the EEPROM Loader. A single-module reset is initiated by assertion of
the following:
4.2.3.1

Port 2 PHY Reset

Port 1 PHY Reset

Virtual PHY Reset
Port 2 PHY Reset
A Port 2 PHY reset is performed by setting the PHY2_RST bit of the Reset Control Register
(RESET_CTL) or the Reset bit in the Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x).
Upon completion of the Port 2 PHY reset, the PHY2_RST and Reset bits are automatically cleared.
No other modules of the LAN9312 are affected by this reset.
In addition to the methods above, the Port 2 PHY is automatically reset after returning from a PHY
power-down mode. This reset differs in that the PHY power-down mode reset does not reload or reset
any of the PHY registers. Refer to Section 7.2.9, "PHY Power-Down Modes," on page 94 for additional
information.
Port 2 PHY reset completion can be determined by polling the PHY2_RST bit in the Reset Control
Register (RESET _CTL) or the Reset bit in the Port x PHY Basic Control Register
(PHY_BASIC_CONTROL_x) until it clears. Under normal conditions, the PHY2_RST and Reset bit will
clear approximately 110uS after the Port 2 PHY reset occurrence.
Note: When using the Reset bit to reset the Port 2 PHY, register bits designated as NASR are not
reset.
Refer to Section 7.2.10, "PHY Resets," on page 95 for additional information on Port 2 PHY resets.
4.2.3.2
Port 1 PHY Reset
A Port 1 PHY reset is performed by setting the PHY1_RST bit of the Reset Control Register
(RESET_CTL) or the Reset bit in the Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x).
Upon completion of the Port 1 PHY reset, the PHY1_RST and Reset bits are automatically cleared.
No other modules of the LAN9312 are affected by this reset.
In addition to the methods above, the Port 1 PHY is automatically reset after returning from a PHY
power-down mode. This reset differs in that the PHY power-down mode reset does not reload or reset
any of the PHY registers. Refer to Section 7.2.9, "PHY Power-Down Modes," on page 94 for additional
information.
Port 1 PHY reset completion can be determined by polling the PHY1_RST bit in the Reset Control
Register (RESET _CTL) or the Reset bit in the Port x PHY Basic Control Register
SMSC LAN9312
39
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
(PHY_BASIC_CONTROL_x) until it clears. Under normal conditions, the PHY1_RST and Reset bit will
clear approximately 110uS after the Port 1 PHY reset occurrence.
Note: When using the Reset bit to reset the Port 1 PHY, register bits designated as NASR are not
reset.
Refer to Section 7.2.10, "PHY Resets," on page 95 for additional information on Port 1 PHY resets.
4.2.3.3
Virtual PHY Reset
A Virtual PHY reset is performed by setting the VPHY_RST bit of the Reset Control Register
(RESET_CTL), VPHY_RST bit in the Power Management Control Register (PMT_CTRL), or Reset in
the Virtual PHY Basic Control Register (VPHY_BASIC_CTRL). No other modules of the LAN9312 are
affected by this reset.
Virtual PHY reset completion can be determined by polling the VPHY_RST bit in the Reset Control
Register (RESET_CTL), the VPHY_RST bit in the Power Management Control Register (PMT_CTRL),
or the Reset bit in the Virtual PHY Basic Control Register (VPHY_BASIC_CTRL) until it clears. Under
normal conditions, the VPHY_RST and Reset bit will clear approximately 1uS after the Virtual PHY
reset occurrence.
Refer to Section 7.3.2, "Virtual PHY Resets," on page 98 for additional information on Virtual PHY
resets.
4.2.4
Configuration Straps
Configuration straps allow various features of the LAN9312 to be automatically configured to user
defined values. Configuration straps can be organized into two main categories: hard-straps and softstraps. Both hard-straps and soft-straps are latched upon Power-On Reset (POR) or pin reset (nRST).
The primary difference between these strap types is that soft-strap default values can be overridden
by the EEPROM Loader, while hard-straps cannot.
Configuration straps which have a corresponding external pin include internal resistors in order to
prevent the signal from floating when unconnected. If a particular configuration strap is connected to
a load, an external pull-up or pull-down resistor should be used to augment the internal resistor to
ensure that it reaches the required voltage level prior to latching. The internal resistor can also be
overridden by the addition of an external resistor.
Note: The system designer must guarantee that configuration strap pins meet the timing
requirements specified in Section 15.5.2, "Reset and Configuration Strap Timing," on page 445.
If configuration strap pins are not at the correct voltage level prior to being latched, the
LAN9312 may capture incorrect strap values.
4.2.4.1
Soft-Straps
Soft-strap values are latched on the release of POR or nRST and are overridden by values from the
EEPROM Loader (when an EEPROM is present). These straps are used as direct configuration values
or as defaults for CPU registers. Some, but not all, soft-straps have an associated pin. Those that do
not have an associated pin, have a tie off default value. All soft-strap values can be overridden by the
EEPROM Loader. Table 4.2 provides a list of all soft-straps and their associated pin or default value.
Straps which have an associated pin are also fully defined in Chapter 3, "Pin Description and
Configuration," on page 26. Refer to Section 10.2.4, "EEPROM Loader," on page 149 for information
on the operation of the EEPROM Loader and the loading of strap values.
Upon setting the DIGITAL_RST bit in the Reset Control Register (RESET_CTL) or upon issuing a
RELOAD command via the EEPROM Command Register (E2P_CMD), these straps return to their
original latched (non-overridden) values if an EEPROM is no longer attached or has been erased. The
associated pins are not re-sampled. (i.e. The value latched on the pin during the last POR or nRST
will be used, not the value on the pin during the digital reset or RELOAD command issuance). If it is
desired to re-latch the current configuration strap pin values, a POR or nRST must be issued.
Revision 2.0 (02-14-13)
40
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 4.2 Soft-Strap Configuration Strap Definitions
PIN / DEFAULT
VALUE
STRAP NAME
DESCRIPTION
LED_en_strap[7:0]
LED Enable Straps: Configures the default value for the
LED_EN bits in the LED Configuration Register
(LED_CFG). A high value configures the associated
LED/GPIO pin as a LED. A low value configures the
associated LED/GPIO pin as a GPIO.
Note:
LED_EN
One pin configures the default for all 8
LED/GPIOs, but 8 separate bits are loaded by the
EEPROM Loader, allowing individual control over
each LED/GPIO.
LED_fun_strap[1:0]
LED Function Straps: Configures the default value for the
LED_FUN bits in the LED Configuration Register
(LED_CFG). When configured low, the corresponding bit
will be cleared. When configured high, the corresponding
bit will be set.
00b
auto_mdix_strap_1
Port 1 Auto-MDIX Enable Strap: Configures the default
value for the Auto-MDIX functionality on Port 1 when the
AMDIXCTL bit in the Port x PHY Special Control/Status
Indication Register
(PHY_SPECIAL_CONTROL_STAT_IND_x) is cleared.
When configured low, Auto-MDIX is disabled. When
configured high, Auto-MDIX is enabled.
AUTO_MDIX_1
Note:
If AMDIXCTL is set, this strap had no effect.
manual_mdix_strap_1
Port 1 Manual MDIX Strap: Configures MDI(0) or MDIX(1)
for Port 1 when the auto_mdix_strap_1 is low and the
AMDIXCTL bit of the Port x PHY Special Control/Status
Indication Register
(PHY_SPECIAL_CONTROL_STAT_IND_x) is cleared.
0b
autoneg_strap_1
Port 1 Auto Negotiation Enable Strap: Configures the
default value for the Auto-Negotiation (PHY_AN) enable bit
in the PHY_BASIC_CTRL_1 register (See
Section 14.4.2.1). When configured low, auto-negotiation is
disabled. When configured high, auto-negotiation is
enabled.
1b
This strap also affects the default value of the following bits:



PHY_SPEED_SEL_LSB and PHY_DUPLEX bits of the
Port x PHY Basic Control Register
(PHY_BASIC_CONTROL_x)
10BASE-T Full Duplex (bit 6) and 10BASE-T Half Duplex
(bit 5) bits of the Port x PHY Auto-Negotiation
Advertisement Register (PHY_AN_ADV_x)
MODE[2:0] bits of the Port x PHY Special Modes Register
(PHY_SPECIAL_MODES_x)
Refer to the respective register definition sections for
additional information.
SMSC LAN9312
41
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 4.2 Soft-Strap Configuration Strap Definitions (continued)
PIN / DEFAULT
VALUE
STRAP NAME
DESCRIPTION
speed_strap_1
Port 1 Speed Select Strap: Configures the default value
for the Speed Select LSB (PHY_SPEED_SEL_LSB) bit in
the PHY_BASIC_CTRL_1 register (See Section 14.4.2.1).
When configured low, 10 Mbps is selected. When
configured high, 100 Mbps is selected.
1b
This strap also affects the default value of the following bits:



PHY_SPEED_SEL_LSB bit of the Port x PHY Basic
Control Register (PHY_BASIC_CONTROL_x)
10BASE-T Full Duplex (bit 6) and 10BASE-T Half Duplex
(bit 5) bits of the Port x PHY Auto-Negotiation
Advertisement Register (PHY_AN_ADV_x)
MODE[2:0] bits of the Port x PHY Special Modes Register
(PHY_SPECIAL_MODES_x)
Refer to the respective register definition sections for
additional information.
duplex_strap_1
Port 1 Duplex Select Strap: Configures the default value
for the Duplex Mode (PHY_DUPLEX) bit in the
PHY_BASIC_CTRL_1 register (See Section 14.4.2.1).
When configured low, half-duplex is selected. When
configured high, full-duplex is selected.
1b
This strap also affects the default value of the following bits:



PHY_DUPLEX bit of the Port x PHY Basic Control
Register (PHY_BASIC_CONTROL_x)
10BASE-T Full Duplex (bit 6) of the Port x PHY AutoNegotiation Advertisement Register (PHY_AN_ADV_x)
MODE[2:0] bits of the Port x PHY Special Modes Register
(PHY_SPECIAL_MODES_x)
Refer to the respective register definition sections for
additional information.
BP_EN_strap_1
Port 1 Backpressure Enable Strap: Configures the
default value for the Port 1 Backpressure Enable
(BP_EN_1) bit of the Port 1 Manual Flow Control Register
(MANUAL_FC_1). When configured low, backpressure is
disabled. When configured high, backpressure is enabled.
1b
FD_FC_strap_1
Port 1 Full-Duplex Flow Control Enable Strap:
Configures the default value of the Port 1 Full-Duplex
Transmit Flow Control Enable (TX_FC_1) and Port 1 FullDuplex Receive Flow Control Enable (RX_FC_1) bits in the
Port 1 Manual Flow Control Register (MANUAL_FC_1),
which are used when manual full-duplex control is selected.
When configured low, full-duplex Pause packet detection
and generation are disabled. When configured high, fullduplex Pause packet detection and generation are enabled.
1b
Revision 2.0 (02-14-13)
42
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 4.2 Soft-Strap Configuration Strap Definitions (continued)
PIN / DEFAULT
VALUE
STRAP NAME
DESCRIPTION
manual_FC_strap_1
Port 1 Manual Flow Control Enable Strap: Configures the
default value of the Port 1 Full-Duplex Manual Flow Control
Select (MANUAL_FC_1) bit in the Port 1 Manual Flow
Control Register (MANUAL_FC_1). When configured low,
flow control is determined by auto-negotiation (if enabled),
and symmetric PAUSE is advertised (bit 10 of the Port x
PHY Auto-Negotiation Advertisement Register
(PHY_AN_ADV_x) is set).
0b
When configured high, flow control is determined by the
Port 1 Full-Duplex Transmit Flow Control Enable
(TX_FC_1) and Port 1 Full-Duplex Receive Flow Control
Enable (RX_FC_1) bits, and symmetric PAUSE is not
advertised (bit 10 of the Port x PHY Auto-Negotiation
Advertisement Register (PHY_AN_ADV_x) is cleared).
auto_mdix_strap_2
Port 2 Auto-MDIX Enable Strap: Configures the default
value for the Auto-MDIX functionality on Port 2 when the
AMDIXCTL bit in the Port x PHY Special Control/Status
Indication Register
(PHY_SPECIAL_CONTROL_STAT_IND_x) is cleared.
When configured low, Auto-MDIX is disabled. When
configured high, Auto-MDIX is enabled.
Note:
AUTO_MDIX_2
If AMDIXCTL is set, this strap had no effect.
manual_mdix_strap_2
Port 2 Manual MDIX Strap: Configures MDI(0) or MDIX(1)
for Port 2 when the auto_mdix_strap_2 is low and the
AMDIXCTL bit of the Port x PHY Special Control/Status
Indication Register
(PHY_SPECIAL_CONTROL_STAT_IND_x) is cleared.
0b
autoneg_strap_2
Port 2 Auto Negotiation Enable Strap: Configures the
default value for the Auto-Negotiation (PHY_AN) enable bit
in the PHY_BASIC_CTRL_2 register (See
Section 14.4.2.1). When configured low, auto-negotiation is
disabled. When configured high, auto-negotiation is
enabled.
1b
This strap also affects the default value of the following bits:



PHY_SPEED_SEL_LSB and PHY_DUPLEX bits of the
Port x PHY Basic Control Register
(PHY_BASIC_CONTROL_x)
10BASE-T Full Duplex (bit 6) and 10BASE-T Half Duplex
(bit 5) bits of the Port x PHY Auto-Negotiation
Advertisement Register (PHY_AN_ADV_x)
MODE[2:0] bits of the Port x PHY Special Modes Register
(PHY_SPECIAL_MODES_x)
Refer to the respective register definition sections for
additional information.
SMSC LAN9312
43
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 4.2 Soft-Strap Configuration Strap Definitions (continued)
PIN / DEFAULT
VALUE
STRAP NAME
DESCRIPTION
speed_strap_2
Port 2 Speed Select Strap: Configures the default value
for the Speed Select LSB (PHY_SPEED_SEL_LSB) bit in
the PHY_BASIC_CTRL_2 register (See Section 14.4.2.1).
When configured low, 10 Mbps is selected. When
configured high, 100 Mbps is selected.
1b
This strap also affects the default value of the following bits:



PHY_SPEED_SEL_LSB bit of the Port x PHY Basic
Control Register (PHY_BASIC_CONTROL_x)
10BASE-T Full Duplex (bit 6) and 10BASE-T Half Duplex
(bit 5) bits of the Port x PHY Auto-Negotiation
Advertisement Register (PHY_AN_ADV_x)
MODE[2:0] bits of the Port x PHY Special Modes Register
(PHY_SPECIAL_MODES_x)
Refer to the respective register definition sections for
additional information.
duplex_strap_2
Port 2 Duplex Select Strap: Configures the default value
for the Duplex Mode (PHY_DUPLEX) bit in the
PHY_BASIC_CTRL_2 register (See Section 14.4.2.1).
When configured low, half-duplex is selected. When
configured high, full-duplex is selected.
1b
This strap also affects the default value of the following bits:



PHY_DUPLEX bit of the Port x PHY Basic Control
Register (PHY_BASIC_CONTROL_x)
10BASE-T Full Duplex (bit 6) of the Port x PHY AutoNegotiation Advertisement Register (PHY_AN_ADV_x)
MODE[2:0] bits of the Port x PHY Special Modes Register
(PHY_SPECIAL_MODES_x)
Refer to the respective register definition sections for
additional information.
BP_EN_strap_2
Port 2 Backpressure Enable Strap: Configures the
default value for the Port 2 Backpressure Enable
(BP_EN_2) bit of the Port 2 Manual Flow Control Register
(MANUAL_FC_2). When configured low, backpressure is
disabled. When configured high, backpressure is enabled.
1b
FD_FC_strap_2
Port 2 Full-Duplex Flow Control Enable Strap:
Configures the default value of the Port 2 Full-Duplex
Transmit Flow Control Enable (TX_FC_2) and Port 2 FullDuplex Receive Flow Control Enable (RX_FC_2) bits in the
Port 2 Manual Flow Control Register (MANUAL_FC_2),
which are used when manual full-duplex control is selected.
When configured low, full-duplex Pause packet detection
and generation are disabled. When configured high, fullduplex Pause packet detection and generation are enabled.
1b
Revision 2.0 (02-14-13)
44
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 4.2 Soft-Strap Configuration Strap Definitions (continued)
PIN / DEFAULT
VALUE
STRAP NAME
DESCRIPTION
manual_FC_strap_2
Port 2 Manual Flow Control Enable Strap: Configures the
default value of the Port 2 Full-Duplex Manual Flow Control
Select (MANUAL_FC_2) bit in the Port 2 Manual Flow
Control Register (MANUAL_FC_2). When configured low,
flow control is determined by auto-negotiation (if enabled),
and symmetric PAUSE is advertised (bit 10 of the Port x
PHY Auto-Negotiation Advertisement Register
(PHY_AN_ADV_x) is set).
0b
When configured high, flow control is determined by the
Port 2 Full-Duplex Transmit Flow Control Enable
(TX_FC_2) and Port 2 Full-Duplex Receive Flow Control
Enable (RX_FC_2) bits, and symmetric PAUSE is not
advertised (bit 10 of the Port x PHY Auto-Negotiation
Advertisement Register (PHY_AN_ADV_x) is cleared).
BP_EN_strap_mii
Port 0(Host MAC) Backpressure Enable Strap:
Configures the default value for the Port 0 Backpressure
Enable (BP_EN_MII) bit of the Port 0(Host MAC) Manual
Flow Control Register (MANUAL_FC_MII). When
configured low, backpressure is disabled. When configured
high, backpressure is enabled.
1b
FD_FC_strap_mii
Port 0(Host MAC) Full-Duplex Flow Control Enable
Strap: Configures the default of the TX_FC_MII and
RX_FC_MII bits in the Port 0(Host MAC) Manual Flow
Control Register (MANUAL_FC_MII) which are used when
manual full-duplex flow control is selected. When
configured low, flow control is disabled on RX/TX. When
configured high, flow control is enabled on RX/TX.
1b
manual_FC_strap_mii
Port 0(Host MAC) Manual Flow Control Enable Strap:
Configures the default value of the MANUAL_FC_MII bit in
the Port 0(Host MAC) Manual Flow Control Register
(MANUAL_FC_MII). When configured low, flow control is
determined by Virtual Auto-Negotiation (if enabled). When
configured high, flow control is determined by TX_FC_MII
and RX_FC_MII bits in the Port 0(Host MAC) Manual Flow
Control Register (MANUAL_FC_MII).
0b
SQE_test_disable_strap_mii
SQE Heartbeat Disable Strap: Configures the Signal
Quality Error (Heartbeat) test function by controlling the
default value of the SQEOFF (bit 0) of the Virtual PHY
Special Control/Status Register
(VPHY_SPECIAL_CONTROL_STATUS). When configured
low, SQEOFF defaults to 0 and SQE test is enabled. When
configured high, SQEOFF defaults to 1 and SQE test is
disabled.
0b
4.2.4.2
Hard-Straps
Hard-straps are latched upon Power-On Reset (POR) or pin reset (nRST) only. Unlike soft-straps,
hard-straps always have an associated pin and cannot be overridden by the EEPROM Loader. These
straps are used as either direct configuration values or as register defaults. Table 4.3 provides a list of
all hard-straps and their associated pin. These straps, along with their pin assignments are also fully
defined in Chapter 3, "Pin Description and Configuration," on page 26.
SMSC LAN9312
45
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 4.3 Hard-Strap Configuration Strap Definitions
STRAP NAME
eeprom_type_strap
DESCRIPTION
EEPROM Type Strap: Configures the EEPROM type.
PIN
EEPROM_TYPE
0 = Microwire Mode
1 = I2C Mode
PHY Address Select Strap: Configures the default MII
management address values for the PHYs and Virtual PHY
as detailed in Section 7.1.1, "PHY Addressing," on page 82.
PHY_ADDR_SEL
4.3
PORT 2 PHY
ADDRESS
phy_addr_sel_strap
PORT 1 PHY
ADDRESS
EEPROM_SIZE_[1:0]
VIRTUAL PHY
ADDRESS
EEPROM Size Strap [1:0]: Configures the EEPROM size
range as specified in Section 10.2, "I2C/Microwire Master
EEPROM Controller," on page 137.
PHY_ADDR_SEL_STRAP
VALUE
eeprom_size_strap[1:0]
0
0
1
2
1
1
2
3
Power Management
The LAN9312 Port 1 and Port 2 PHYs and the Host MAC support several power management and
wakeup features.
The LAN9312 can be programmed to issue an external wake signal (PME) via several methods,
including wake on LAN, wake on link status change (energy detect), and magic packet wakeup. The
PME signal is ideal for triggering system power-up using remote Ethernet wakeup events. A simplified
diagram of the logic that controls the PME and PME_INT signals can be seen in Figure 4.1.
The PME module handles the latching of the Port 1 & 2 PHY Energy-Detect Status (ED_STS1 and
ED_STS2) and Wake-On LAN Status (WOL_STS) bits of the Power Management Control Register
(PMT_CTRL). This module also masks the status bits with the corresponding enable bits (ED_EN1,
ED_EN2, WOL_EN) and combines the results together to generate the PME_INT status bit in the
Interrupt Status Register (INT_STS). The PME_INT status bit is then masked with the PME_EN bit and
conditioned before becoming the PME output pin.
The PME output characteristics can be configured via the PME_TYPE, PME_IND, and PME_POL bits
of the Power Management Control Register (PMT_CTRL). These bits allow the PME to be open-drain,
active high push-pull, or active-low push-pull and configure the output to be continuous, or pulse for
50mS.
Revision 2.0 (02-14-13)
46
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
WUFR (bit 6) of
HMAC_WUCSR register
WOL_EN (bit 9) of
PMT_CTRL register
Host MAC
WUEN (bit 2) of
HMAC_WUCSR register
WOL_STS (bit 5) of
PMT_CTRL register
MPR (bit 5) of
HMAC_WUCSR register
MPEN (bit 1) of
HMAC_WUCSR register
ED_EN1 (bit 14) of
PMT_CTRL register
Port 1 & 2 PHYs
INT7 (bit 7) of
PHY_INTERRUPT_SOURCE_1 register
ED_STS1 (bit 16) of
PMT_CTRL register
INT7_MASK (bit 7) of
PHY_INTERRUPT_SOURCE_1 register
ED_EN2 (bit 15) of
PMT_CTRL register
INT7 (bit 7) of
PHY_INTERRUPT_SOURCE_2 register
ED_STS2 (bit 17) of
PMT_CTRL register
INT7_MASK (bit 7) of
PHY_INTERRUPT_SOURCE_2 register
PME_INT (bit 17)
of INT_STS register
Other System
Interrupts
Polarity &
Buffer Type
Logic
Denotes a level-triggered "sticky" status bit
PME_INT_EN (bit 17)
of INT_EN register
IRQ
Power Management Control
IRQ_EN (bit 8)
of IRQ_CFG register
PME_EN (bit 1) of
PMT_CTRL register
50ms
PME_IND (bit 3) of
PMT_CTRL register
PME
LOGIC
PME_POL (bit 2) of
PMT_CTRL register
PME_TYPE (bit 6) of
PMT_CTRL register
Figure 4.1 PME and PME_INT Signal Generation
4.3.1
Port 1 & 2 PHY Power Management
The Port 1 & 2 PHYs provide independent general power-down and energy-detect power-down modes
which reduce PHY power consumption. General power-down mode provides power savings by
powering down the entire PHY, except the PHY management control interface. General power-down
mode must be manually enabled and disabled as described in Section 7.2.9.1, "PHY General PowerDown," on page 95.
In energy-detect power-down mode, the PHY will resume from power-down when energy is seen on
the cable (typically from link pulses). If the ENERGYON interrupt (INT7) of either PHYs Port x PHY
Interrupt Mask Register (PHY_INTERRUPT_MASK_x) is unmasked, then the corresponding PHY will
generate an interrupt. These interrupts are reflected in the Interrupt Status Register (INT_STS) bit 27
(PHY_INT2) for the Port 2 PHY, and bit 26 (PHY_INT1) for the Port 1 PHY. These interrupts can be
used to trigger the IRQ interrupt output pin, as described in Section 5.2.3, "Ethernet PHY Interrupts,"
on page 52. Refer to Section 7.2.9.2, "PHY Energy Detect Power-Down," on page 95 for details on the
operation and configuration of the PHY energy-detect power-down mode.
SMSC LAN9312
47
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
The Port 1 & 2 PHY energy-detect events are capable of asserting the PME output by additionally
setting the PME_EN and ED_EN2 (Port 2 PHY) or ED_EN1 (Port 1 PHY) bits of the Power
Management Control Register (PMT_CTRL).
4.3.2
Host MAC Power Management
The Host MAC provides wake-up frame and magic packet detection modes. When enabled in the Host
MAC Wake-up Control and Status Register (HMAC_WUCSR) (via the WUEN bit for wake-up frames,
and the MPEN bit for magic packets), detection of wake-up frames or magic packets causes the WUFR
and MPR bits of the HMAC_WUCSR register to set, respectively. If either of the WUFR and MPR bits
are set, the WOL_STS bit of the Power Management Control Register (PMT_CTRL) will be set. These
events can enable PME output assertion by additionally setting the PME_EN bit of the Power
Management Control Register (PMT_CTRL).
The IRQ interrupt output can be triggered by a wake-up frame or magic packet as described in Section
5.2.6, "Power Management Interrupts," on page 53.
Refer to Section 9.5, "Wake-up Frame Detection," on page 116 and Section 9.5.1, "Magic Packet
Detection," on page 118 for additional details on these features.
Revision 2.0 (02-14-13)
48
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 5 System Interrupts
5.1
Functional Overview
This chapter describes the system interrupt structure of the LAN9312. The LAN9312 provides a multitier programmable interrupt structure which is controlled by the System Interrupt Controller. The
programmable system interrupts are generated internally by the various LAN9312 sub-modules and
can be configured to generate a single external host interrupt via the IRQ interrupt output pin. The
programmable nature of the host interrupt provides the user with the ability to optimize performance
dependent upon the application requirements. The IRQ interrupt buffer type, polarity, and de-assertion
interval are modifiable. The IRQ interrupt can be configured as an open-drain output to facilitate the
sharing of interrupts with other devices. All internal interrupts are maskable and capable of triggering
the IRQ interrupt.
5.2
Interrupt Sources
The LAN9312 is capable of generating the following interrupt types:

1588 Time Stamp Interrupts (Port 2,1,0 and GPIO 9,8)

Switch Fabric Interrupts (Buffer Manager, Switch Engine, and Port 2,1,0 MACs)

Ethernet PHY Interrupts (Port 1,2 PHYs)

GPIO Interrupts (GPIO[11:0])

Host MAC Interrupts (FIFOs)

Power Management Interrupts

General Purpose Timer Interrupt (GPT)

Software Interrupt (General Purpose)

Device Ready Interrupt
All interrupts are accessed and configured via registers arranged into a multi-tier, branch-like structure,
as shown in Figure 5.1. At the top level of the LAN9312 interrupt structure are the Interrupt Status
Register (INT_STS), Interrupt Enable Register (INT_EN), and Interrupt Configuration Register
(IRQ_CFG).
The Interrupt Status Register (INT_STS) and Interrupt Enable Register (INT_EN) aggregate and
enable/disable all interrupts from the various LAN9312 sub-modules, combining them together to
create the IRQ interrupt. These registers provide direct interrupt access/configuration to the Host MAC,
General Purpose Timer, software, and device ready interrupts. These interrupts can be monitored,
enabled/disabled, and cleared, directly within these two registers. In addition, interrupt event
indications are provided for the 1588 Time Stamp, Switch Fabric, Port 1 & 2 Ethernet PHYs, Power
Management, and GPIO interrupts. These interrupts differ in that the interrupt sources are generated
and cleared in other sub-block registers. The INT_STS register does not provide details on what
specific event within the sub-module caused the interrupt, and requires the software to poll an
additional sub-module interrupt register (as shown in Figure 5.1) to determine the exact interrupt
source and clear it. For interrupts which involve multiple registers, only after the interrupt has been
serviced and cleared at its source will it be cleared in the INT_STS register.
The Interrupt Configuration Register (IRQ_CFG) is responsible for enabling/disabling the IRQ interrupt
output pin as well as configuring its properties. The IRQ_CFG register allows the modification of the
IRQ pin buffer type, polarity, and de-assertion interval. The de-assertion timer guarantees a minimum
interrupt de-assertion period for the IRQ output and is programmable via the INT_DEAS field of the
Interrupt Configuration Register (IRQ_CFG). A setting of all zeros disables the de-assertion timer. The
de-assertion interval starts when the IRQ pin de-asserts, regardless of the reason.
Note: The de-assertion timer does not apply to the PME interrupt. Assertion of the PME interrupt
does not affect the de-assertion timer.
SMSC LAN9312
49
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Top Level Interrupt Registers
(System CSRs)
INT_CFG
INT_STS
INT_EN
Bit 29 (1588_EVNT)
of INT_STS register
1588 Time Stamp Interrupt Register
1588_INT_STS_EN
Switch Fabric Interrupt Registers
Bit 28 (SWITCH_INT)
of INT_STS register
SW_IMR
SW_IPR
Buffer Manager Interrupt Registers
Bit 6 (BM)
of SW_IPR register
BM_IMR
BM_IPR
Switch Engine Interrupt Registers
Bit 5 (SWE)
of SW_IPR register
SWE_IMR
SWE_IPR
Port [2,1,0] MAC Interrupt Registers
Bits [2,1,0] (MAC_[2,1,MII])
of SW_IPR register
MAC_IMR_[2,1,MII]
MAC_IPR_[2,1,MII]
Port 2 PHY Interrupt Registers
Bit 27 (PHY_INT2)
of INT_STS register
PHY_INTERRUPT_SOURCE_2
PHY_INTERRUPT_MASK_2
Port 1 PHY Interrupt Registers
Bit 26 (PHY_INT1)
of INT_STS register
PHY_INTERRUPT_SOURCE_1
PHY_INTERRUPT_MASK_1
Bit 17 (PME_INT)
of INT_STS register
Bit 12 (GPIO)
of INT_STS register
Power Management Control Register
PMT_CTRL
GPIO Interrupt Register
GPIO_INT_STS_EN
Figure 5.1 Functional Interrupt Register Hierarchy
Revision 2.0 (02-14-13)
50
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
The following sections detail each category of interrupts and their related registers. Refer to
Chapter 14, "Register Descriptions," on page 166 for bit-level definitions of all interrupt registers.
5.2.1
1588 Time Stamp Interrupts
Multiple 1588 Time Stamp interrupt sources are provided by the LAN9312. The top-level 1588_EVNT
(bit 29) of the Interrupt Status Register (INT_STS) provides indication that a 1588 interrupt event
occurred in the 1588 Interrupt Status and Enable Register (1588_INT_STS_EN).
The 1588 Interrupt Status and Enable Register (1588_INT_STS_EN) provides enabling/disabling and
status of all 1588 interrupt conditions. These include TX/RX 1588 clock capture indication on Ports
2,1,0, 1588 clock capture for GPIO[8:9] events, as well as 1588 timer interrupt indication.
In order for a 1588 interrupt event to trigger the external IRQ interrupt pin, the desired 1588 interrupt
event must be enabled in the 1588 Interrupt Status and Enable Register (1588_INT_STS_EN), bit 29
(1588_EVNT_EN) of the Interrupt Enable Register (INT_EN) must be set, and IRQ output must be
enabled via bit 8 (IRQ_EN) of the Interrupt Configuration Register (IRQ_CFG).
For additional details on the 1588 Time Stamp interrupts, refer to Section 11.6, "IEEE 1588 Interrupts,"
on page 160.
5.2.2
Switch Fabric Interrupts
Multiple Switch Fabric interrupt sources are provided by the LAN9312 in a three-tiered register
structure as shown in Figure 5.1. The top-level SWITCH_INT (bit 28) of the Interrupt Status Register
(INT_STS) provides indication that a Switch Fabric interrupt event occurred in the Switch Engine
Interrupt Pending Register (SWE_IPR).
In turn, the Switch Engine Interrupt Pending Register (SWE_IPR) and Switch Engine Interrupt Mask
Register (SWE_IMR) provide status and enabling/disabling of all Switch Fabric sub-modules interrupts
(Buffer Manager, Switch Engine, and Port 2,1,0 MACs).
The low-level Switch Fabric sub-module interrupt pending and mask registers of the Buffer Manager,
Switch Engine, and Port 2,1,0 MACs provide multiple interrupt sources from their respective submodules. These low-level registers provide the following interrupt sources:

Buffer Manager (Buffer Manager Interrupt Mask Register (BM_IMR) and Buffer Manager Interrupt
Pending Register (BM_IPR))
—Status B Pending
—Status A Pending

Switch Engine (Switch Engine Interrupt Mask Register (SWE_IMR) and Switch Engine Interrupt
Pending Register (SWE_IPR))
—Interrupt Pending

Port 2,1,0 MACs (Port x MAC Interrupt Mask Register (MAC_IMR_x) and Port x MAC Interrupt
Pending Register (MAC_IPR_x))
—No currently supported interrupt sources. These registers are reserved for future use.
In order for a Switch Fabric interrupt event to trigger the external IRQ interrupt pin, the following must
be configured:

The desired Switch Fabric sub-module interrupt event must be enabled in the corresponding mask
register (Buffer Manager Interrupt Mask Register (BM_IMR) for the Buffer Manager, Switch Engine
Interrupt Mask Register (SWE_IMR) for the Switch Engine, and/or Port x MAC Interrupt Mask
Register (MAC_IMR_x) for the Port 2,1,0 MACs)

The desired Switch Fabric sub-module interrupt event must be enabled in the Switch Engine
Interrupt Mask Register (SWE_IMR)

Bit 28 (SWITCH_INT_EN) of the Interrupt Enable Register (INT_EN) must be set

IRQ output must be enabled via bit 8 (IRQ_EN) of the Interrupt Configuration Register (IRQ_CFG)
SMSC LAN9312
51
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
For additional details on the Switch Fabric interrupts, refer to Section 6.6, "Switch Fabric Interrupts,"
on page 81.
5.2.3
Ethernet PHY Interrupts
The Port 1 and Port 2 PHYs each provide a set of identical interrupt sources. The top-level PHY_INT1
(bit 26) and PHY_INT2 (bit 27) of the Interrupt Status Register (INT_STS) provides indication that a
PHY interrupt event occurred in the Port x PHY Interrupt Source Flags Register
(PHY_INTERRUPT_SOURCE_x).
Port 1 and Port 2 PHY interrupts are enabled/disabled via their respective Port x PHY Interrupt Mask
Register (PHY_INTERRUPT_MASK_x). The source of a PHY interrupt can be determined and cleared
via the Port x PHY Interrupt Source Flags Register (PHY_INTERRUPT_SOURCE_x). The Port 1 and
Port 2 PHYs are each capable of generating unique interrupts based on the following events:

ENERGYON Activated

Auto-Negotiation Complete

Remote Fault Detected

Link Down (Link Status Negated)

Auto-Negotiation LP Acknowledge

Parallel Detection Fault

Auto-Negotiation Page Received
In order for a Port 1 or Port 2 interrupt event to trigger the external IRQ interrupt pin, the desired PHY
interrupt event must be enabled in the corresponding Port x PHY Interrupt Mask Register
(PHY_INTERRUPT_MASK_x), the PHY_INT1(Port 1 PHY) and/or PHY_INT2(Port 2 PHY) bits of the
Interrupt Enable Register (INT_EN) must be set, and IRQ output must be enabled via bit 8 (IRQ_EN)
of the Interrupt Configuration Register (IRQ_CFG).
For additional details on the Ethernet PHY interrupts, refer to Section 7.2.8.1, "PHY Interrupts," on
page 94.
5.2.4
GPIO Interrupts
Each GPIO[11:0] of the LAN9312 is provided with its own interrupt. The top-level GPIO (bit 12) of the
Interrupt Status Register (INT_STS) provides indication that a GPIO interrupt event occurred in the
General Purpose I/O Interrupt Status and Enable Register (GPIO_INT_STS_EN). The General
Purpose I/O Interrupt Status and Enable Register (GPIO_INT_STS_EN) provides enabling/disabling
and status of each GPIO[11:0] interrupt.
In order for a GPIO interrupt event to trigger the external IRQ interrupt pin, the desired GPIO interrupt
must be enabled in the General Purpose I/O Interrupt Stat us and Enable Regist er
(GPIO_INT_STS_EN), bit 12 (GPIO_EN) of the Interrupt Enable Register (INT_EN) must be set, and
IRQ output must be enabled via bit 8 (IRQ_EN) of the Interrupt Configuration Register (IRQ_CFG).
For additional details on the GPIO interrupts, refer to Section 13.2.2, "GPIO Interrupts," on page 163.
5.2.5
Host MAC Interrupts
The top-level Interrupt Status Register (INT_STS), and Interrupt Enable Register (INT_EN) provide the
status and enabling/disabling of multiple Host MAC related interrupts. All Host MAC interrupts are
monitored and configured directly within these two registers. The following Host MAC related interrupt
events are supported:

TX Stopped

RX Stopped

RX Dropped Frame Counter Halfway
Revision 2.0 (02-14-13)
52
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet

TX IOC

RX DMA

TX Status FIFO Overflow

Receive Watchdog Time-Out

Receiver Error

Transmitter Error

TX Data FIFO Underrun

TX Data FIFO Overrun

TX Data FIFO Available

TX Status FIFO Full

TX Status FIFO Level

RX Dropped Frame

RX Data FIFO Level

RX Status FIFO Full

RX Status FIFO Level
In order for a Host MAC interrupt event to trigger the external IRQ interrupt pin, the desired Host MAC
interrupt event must be enabled in the Interrupt Enable Register (INT_EN), and IRQ output must be
enabled via bit 8 (IRQ_EN) of the Interrupt Configuration Register (IRQ_CFG).
Refer to the Interrupt Status Register (INT_STS) on page 174 and Chapter 9, "Host MAC," on page 112
for additional information on bit definitions and Host MAC operation.
5.2.6
Power Management Interrupts
Multiple Power Management Event interrupt sources are provided by the LAN9312. The top-level
PME_INT (bit 17) of the Interrupt Status Register (INT_STS) provides indication that a Power
Management interrupt event occurred in the Power Management Control Register (PMT_CTRL).
The Power Management Control Register (PMT_CTRL) provides enabling/disabling and status of all
Power Management conditions. These include energy-detect on the Port 1/2 PHYs, and Wake-On-LAN
(wake-up frame or magic packet) detection by the Host MAC.
In order for a Power Management interrupt event to trigger the external IRQ interrupt pin, the desired
Power Management interrupt event must be enabled in the Power Management Control Register
(PMT_CTRL) (bits 15, 14, and/or 9), bit 17 (PME_INT_EN) of the Interrupt Enable Register (INT_EN)
must be set, and IRQ output must be enabled via bit 8 (IRQ_EN) of the Interrupt Configuration Register
(IRQ_CFG).
For additional details on power management, refer to Section 4.3, "Power Management," on page 46.
5.2.7
General Purpose Timer Interrupt
A General Purpose Timer (GPT) interrupt is provided in the top-level Interrupt Status Register
(INT_STS) and Interrupt Enable Register (INT_EN) (bit 19). This interrupt is issued when the General
Purpose Timer Configuration Register (GPT_CFG) wraps past zero to FFFFh, and is cleared when bit
19 of the Interrupt Status Register (INT_STS) is written with 1.
In order for a General Purpose Timer interrupt event to trigger the external IRQ interrupt pin, the GPT
must be enabled via the bit 29 (TIMER_EN) in the General Purpose Timer Configuration Register
(GPT_CFG), bit 19 of the Interrupt Enable Register (INT_EN) must be set, and IRQ output must be
enabled via bit 8 (IRQ_EN) of the Interrupt Configuration Register (IRQ_CFG).
SMSC LAN9312
53
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
For additional details on the General Purpose Timer, refer to Section 12.1, "General Purpose Timer,"
on page 161.
5.2.8
Software Interrupt
A general purpose software interrupt is provided in the top level Interrupt Status Register (INT_STS)
and Interrupt Enable Register (INT_EN). The SW_INT interrupt (bit 31) of the Interrupt Status Register
(INT_STS) is generated when SW_INT_EN (bit 31) of the Interrupt Enable Register (INT_EN) is set.
This interrupt provides an easy way for software to generate an interrupt, and is designed for general
software usage.
5.2.9
Device Ready Interrupt
A device ready interrupt is provided in the top-level Interrupt Status Register (INT_STS) and Interrupt
Enable Register (INT_EN). The READY interrupt (bit 30) of the Interrupt Status Register (INT_STS)
indicates that the LAN9312 is ready to be accessed after a power-up or reset condition. Writing a 1 to
this bit in the Interrupt Status Register (INT_STS) will clear it.
In order for a device ready interrupt event to trigger the external IRQ interrupt pin, bit 30 of the Interrupt
Enable Register (INT_EN) must be set, and IRQ output must be enabled via bit 8 (IRQ_EN) of the
Interrupt Configuration Register (IRQ_CFG).
Revision 2.0 (02-14-13)
54
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 6 Switch Fabric
6.1
Functional Overview
At the core of the LAN9312 is the high performance, high efficiency 3 port Ethernet switch fabric. The
switch fabric contains a 3 port VLAN layer 2 switch engine that supports untagged, VLAN tagged, and
priority tagged frames. The switch fabric provides an extensive feature set which includes spanning
tree protocol support, multicast packet filtering and Quality of Service (QoS) packet prioritization by
VLAN tag, destination address, port default value or DIFFSERV/TOS, allowing for a range of
prioritization implementations. 32K of buffer RAM allows for the storage of multiple packets while
forwarding operations are completed, and a 1K entry forwarding table provides room for MAC address
forwarding tables. Each port is allocated a cluster of 4 dynamic QoS queues which allow each queue
size to grow and shrink with traffic, effectively utilizing all available memory. This memory is managed
dynamically via the buffer manager block within the switch fabric. All aspects of the switch fabric are
managed via the switch fabric configuration and status registers (CSR), which are indirectly accessible
via the memory mapped system control and status registers.
The switch fabric consists of four major block types:

Switch Fabric CSRs - These registers provide access to various switch fabric parameters for
configuration and monitoring.

10/100 Ethernet MACs - A total of three MACs are included in the switch fabric which provide basic
10/100 Ethernet functionality for each switch fabric port.

Switch Engine (SWE) - This block is the core of the switch fabric and provides VLAN layer 2
switching for all three switch ports.

Buffer Manager (BM) - This block provides control of the free buffer space, transmit queues, and
scheduling.
Refer to Figure 2.1 Internal LAN9312 Block Diagram on page 21 for details on the interconnection of
the switch fabric blocks within the LAN9312.
6.2
Switch Fabric CSRs
The switch fabric CSRs provide register level access to the various parameters of the switch fabric.
Switch fabric related registers can be classified into two main categories based upon their method of
access: direct and indirect.
The directly accessible switch fabric registers are part of the main system CSRs of the LAN9312 and
are detailed in Section 14.2.6, "Switch Fabric," on page 229. These registers provide switch fabric
manual flow control (Ports 0-2), data/command registers (for access to the indirect switch fabric
registers), and switch MAC address configuration.
The indirectly accessible switch fabric registers reside within the switch fabric and must be accessed
indirectly via the Switch Fabric CSR Interface Data Register (SWITCH_CSR_DATA) and Switch Fabric
CSR Interface Command Register (SWITCH_CSR_CMD), or the set of Switch Fabric CSR Interface
Direct Data Register (SWITCH_CSR_DIRECT_DATA). The indirectly accessible switch fabric CSRs
provide full access to the many configurable parameters of the switch engine, buffer manager, and
each switch port. The switch fabric CSRs are detailed in Section 14.5, "Switch Fabric Control and
Status Registers," on page 308.
For detailed descriptions of all switch fabric related registers, refer to Chapter 14, "Register
Descriptions," on page 166.
SMSC LAN9312
55
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
6.2.1
Switch Fabric CSR Writes
To perform a write to an individual switch fabric register, the desired data must first be written into the
Switch Fabric CSR Interface Data Register (SWITCH_CSR_DATA). The write cycle is initiated by
performing a single write to the Switch Fabric CSR Interface Command Register
(SWITCH_CSR_CMD) with CSR_BUSY (bit 31) set, the CSR_ADDRESS field (bits 15:0) set to the
desired register address, the R_nW (bit 30) cleared, the AUTO_INC and AUTO_DEC fields cleared,
and the desired CSR byte enable bits selected (bits 19:16). The completion of the write cycle is
indicated by the clearing of the CSR_BUSY bit.
A second write method may be used which utilizes the auto increment/decrement function of the
Switch Fabric CSR Interface Command Register (SWITCH_CSR_CMD) for writing sequential register
addresses. When using this method, the Switch Fabric CSR Interface Command Register
(SWITCH_CSR_CMD) must first be written with the auto increment(AUTO_INC) or auto
decrement(AUTO_DEC) bit set, the CSR_ADDRESS field written with the desired register address, the
R_nW bit cleared, and the desired CSR byte enable bits selected (typically all set). The write cycles
are then initiated by writing the desired data into the Switch Fabric CSR Interface Data Register
(SWITCH_CSR_DATA). The completion of the write cycle is indicated by the clearing of the
CSR_BUSY bit, at which time the address in the Switch Fabric CSR Interface Command Register
(SWITCH_CSR_CMD) is incremented or decremented accordingly. The user may then initiate a
subsequent write cycle by writing the desired data into the Switch Fabric CSR Interface Data Register
(SWITCH_CSR_DATA).
The third write method is to use the direct data range write function. Writes within the Switch Fabric
CSR Interface Direct Data Register (SWITCH_CSR_DIRECT_DATA) address range automatically set
the appropriate register address, set all four byte enable bits (CSR_BE[3:0]), clears the R_nW bit, and
sets the CSR_BUSY bit of the Switch Fabric CSR Interface Command Register
(SWITCH_CSR_CMD). The completion of the write cycle is indicated by the clearing of the
CSR_BUSY bit. Since the address range of the switch fabric CSRs exceeds that of the Switch Fabric
CSR Interface Direct Data Register (SWITCH_CSR_DIRECT_DATA) address range, a sub-set of the
switch fabric CSRs are mapped to the Switch Fabric CSR Interface Direct Data Register
(SWITCH_CSR_DIRECT_DATA) address range as detailed in Table 14.3, “Switch Fabric CSR to
SWITCH_CSR_DIRECT_DATA Address Range Map,” on page 240.
Figure 6.1 illustrates the process required to perform a switch fabric CSR write. The minimum wait
periods as specified in Table 8.1, “Read After Write Timing Rules,” on page 102 are required where
noted.
Revision 2.0 (02-14-13)
56
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
CSR Write
CSR Write Auto
Increment /
Decrement
Idle
Idle
Idle
Write Data
Register
Write
Command
Register
Write
Direct
Data
Register
Range
CSR Write Direct
Address
min wait period
Write
Command
Register
Write Data
Register
CSR_BUSY = 0
Read
Command
Register
CSR_BUSY = 1
min wait period
CSR_BUSY = 0
Read
Command
Register
min wait period
CSR_BUSY = 0
CSR_BUSY = 1
Read
Command
Register
CSR_BUSY = 1
Figure 6.1 Switch Fabric CSR Write Access Flow Diagram
6.2.2
Switch Fabric CSR Reads
To perform a read of an individual switch fabric register, the read cycle must be initiated by performing
a single write to the Switch Fabric CSR Interface Command Register (SWITCH_CSR_CMD) with
CSR_BUSY (bit 31) set, the CSR_ADDRESS field (bits 15:0) set to the desired register address, the
R_nW (bit 30) set, and the AUTO_INC and AUTO_DEC fields cleared. Valid data is available for
reading when the CSR_BUSY bit is cleared, indicating that the data can be read from the Switch Fabric
CSR Interface Data Register (SWITCH_CSR_DATA).
A second read method may be used which utilizes the auto increment/decrement function of the Switch
Fabric CSR Interface Command Register (SWITCH_CSR_CMD) for reading sequential register
addresses. When using this method, the Switch Fabric CSR Interface Command Register
(SWITCH_CSR_CMD) must first be written with the auto increment(AUTO_INC) or auto
decrement(AUTO_DEC) bit set, the CSR_ADDRESS field written with the desired register address,
and the R_nW bit set. The completion of a read cycle is indicated by the clearing of the CSR_BUSY
bit, at which time the data can be read from the Switch Fabric CSR Interface Data Register
(SWITCH_CSR_DATA). When the data is read, the address in the Switch Fabric CSR Interface
Command Register (SWITCH_CSR_CMD) is incremented or decremented accordingly, and another
read cycle is started automatically. The user should clear the AUTO_INC and AUTO_DEC bits before
reading the last data to avoid an unintended read cycle.
Figure 6.2 illustrates the process required to perform a switch fabric CSR read. The minimum wait
periods as specified in Table 8.1, “Read After Write Timing Rules,” on page 102 are required where
noted.
SMSC LAN9312
57
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
CSR Read
CSR Read Auto
Increment /
Decrement
Idle
Idle
Write
Command
Register
Write
Command
Register
min wait period
Read
Command
Register
min wait period
min wait period
CSR_BUSY = 1
Read
Command
Register
CSR_BUSY = 0
CSR_BUSY = 1
CSR_BUSY = 0
last
data?
Read Data
Register
No
Read Data
Register
Yes
Write
Command
Register
Read Data
Register
Figure 6.2 Switch Fabric CSR Read Access Flow Diagram
6.2.3
Flow Control Enable Logic
Each switch fabric port (0,1,2) is provided with two flow control enable inputs per port, one for
transmission and one for reception. Flow control on transmission allows the transmitter to generate
back pressure in half-duplex mode, and pause packets in full-duplex. Flow control in reception enables
the reception of pause packets to pause transmissions.
The state of these enables is based on the state of the ports duplex and Auto-negotiation settings and
the values of the corresponding Manual Flow Control register (Port 1 Manual Flow Control Register
(MANUAL_FC_1), Port 2 Manual Flow Control Register (MANUAL_FC_2), or Port 0(Host MAC)
Manual Flow Control Register (MANUAL_FC_MII)). Table 6.1 details the switch fabric flow control
enable logic.
When in half-duplex mode, the transmit flow control (back pressure) enable is determined directly by
the BP_EN_x bit of the ports manual flow control register. When Auto-negotiation is disabled, or the
MANUAL_FC_x bit of the ports manual flow control register is set, the switch port flow control enables
during full-duplex are determined by the TX_FC_x and RX_FC_x bits of the ports manual flow control
Revision 2.0 (02-14-13)
58
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
register. When Auto-negotiation is enabled and the MANUAL_FC_x bit is cleared, the switch port flow
control enables during full-duplex are determined by Auto-negotiation.
Note: The flow control values in the Port x PHY Auto-Negotiation Advertisement Register
(PHY_AN_AD V_ x) an d Virtual PHY Au to -N egotia tio n Advertisement Register
(VPHY_AN_ADV) are not affected by the values of the manual flow control register. Refer to
Section 7.2.5.1, "PHY Pause Flow Control," on page 92 and Section 7.3.1.3, "Virtual PHY
Pause Flow Control," on page 98 for additional information on PHY and Virtual PHY flow
control settings respectively.
CASE
MANUAL_FC_X
AN ENABLE
AN COMPLETE
LP AN ABLE
DUPLEX
AN PAUSE
ADVERTISEMENT
(Note 6.2)
AN ASYM PAUSE
ADVERTISEMENT
(Note 6.2)
LP PAUSE
ABILITY
(Note 6.2)
LP ASYM PAUSE
ABILITY
(Note 6.2)
RX FLOW CONTROL
ENABLE
TX FLOW CONTROL
ENABLE
Table 6.1 Switch Fabric Flow Control Enable Logic
-
1
X
X
X
Half
X
X
X
X
0
BP_EN_x
-
X
0
X
X
Half
X
X
X
X
0
BP_EN_x
-
1
X
X
X
Full
X
X
X
X
RX_FC_x
TX_FC_x
-
X
0
X
X
Full
X
X
X
X
RX_FC_x
TX_FC_x
1
0
1
0
X
X
X
X
X
X
0
0
2
0
1
1
0
Half (Note 6.1)
X
X
X
X
0
BP_EN_x
3
0
1
1
1
Half
X
X
X
X
0
BP_EN_x
4
0
1
1
1
Full
0
0
X
X
0
0
5
0
1
1
1
Full
0
1
0
X
0
0
6
0
1
1
1
Full
0
1
1
0
0
0
7
0
1
1
1
Full
0
1
1
1
0
1
8
0
1
1
1
Full
1
0
0
X
0
0
9
0
1
1
1
Full
1
X
1
X
1
1
10
0
1
1
1
Full
1
1
0
0
0
0
11
0
1
1
1
Full
1
1
0
1
1
0
Note 6.1
If Auto-negotiation is enabled and complete, but the link partner is not Auto-negotiation
capable, half-duplex is forced via the parallel detect function.
Note 6.2
For the Port 1 and Port 2 PHYs, these are the bits from the Port x PHY Auto-Negotiation
Advertisement Register (PHY_AN_ADV_x) and Port x PHY Auto-Negotiation Link Partner
Base Page Ability Register (PHY_AN_LP_BASE_ABILITY_x). For the Virtual PHY, these
are the local/partner swapped outputs from the bits in the Virtual PHY Auto-Negotiation
Advertisement Register (VPHY_AN_ADV) and Virtual PHY Auto-Negotiation Link Partner
Base Page Ability Register (VPHY_AN_LP_BASE_ABILITY). Refer to Section 7.3.1,
"Virtual PHY Auto-Negotiation," on page 96 for more information.
SMSC LAN9312
59
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Per Table 6.1, the following cases are possible:

Case 1 - Auto-negotiation is still in progress. Since the result is not yet established, flow control is
disabled.

Case 2 - Auto-negotiation is enabled and unsuccessful (link partner not Auto-negotiation capable).
The link partner ability is undefined, effectively a don’t-care value, in this case. The duplex setting
will default to half-duplex in this case. Flow control is determined by the BP_EN_x bit.

Case 3 - Auto-negotiation is enabled and successful with half-duplex as a result. The link partner
ability is undefined since it only applies to full-duplex operation. Flow control is determined by the
BP_EN_x bit.

Cases 4-11 -Auto-negotiation is enabled and successful with full-duplex as the result. In these
cases, the advertisement registers and the link partner ability controls the RX and TX enables.
These cases match IEEE 802.3 Annex 28B.3.
Cases
6.3
4,5,6,8,10 - No flow control enabled
Case
7 - Asymmetric pause towards partner (away from switch port)
Case
9 - Symmetric pause
Case
11 - Asymmetric pause from partner (towards switch port)
10/100 Ethernet MACs
The switch fabric contains three 10/100 MAC blocks, one for each switch port (0,1,2). The 10/100 MAC
provides the basic 10/100 Ethernet functionality, including transmission deferral and collision backoff/retry, receive/transmit FCS checking and generation, receive/transmit pause flow control, and
transmit back pressure. The 10/100 MAC also includes RX and TX FIFOs and per port statistic
counters.
6.3.1
Receive MAC
The receive MAC (IEEE 802.3) sublayer decomposes Ethernet packets acquired via the internal MII
interface by stripping off the preamble sequence and Start of Frame Delimiter (SFD). The receive MAC
checks the FCS, the MAC Control Type, and the byte count against the drop conditions. The packet
is stored in the RX FIFO as it is received.
The receive MAC determines the validity of each received packet by checking the Type field, FCS, and
oversize or undersize conditions. All bad packets will be either immediately dropped or marked (at the
end) as bad packets.
Oversized packets are normally truncated at 1519 or 1523 (VLAN tagged) octets and marked as
erroneous. The MAC can be configured to accept packets up to 2048 octets (inclusive), in which case
the oversize packets are truncated at 2048 bytes and marked as erroneous.
Undersized packets are defined as packets with a length less than the minimum packet size. The
minimum packet size is defined to be 64 bytes, exclusive of preamble sequence and SFD.
The FCS and length/type fields of the frame is checked to detect if the packet has a valid MAC control
frame. When the MAC receives a MAC control frame with a valid FCS and determines the operation
code is a pause command (Flow Control frame), the MAC will load its internal pause counter with the
Number_of_Slots variable from the MAC control frame just received. Anytime the internal pause
counter is zero, the transmit MAC will be allowed to transmit (XON). If the internal pause counter is
not zero, the receive MAC will not allow the transmit MAC to transmit (XOFF). When the transmit MAC
detects an XOFF condition it will continue to transmit the current packet, terminating transmission after
the current packet has been transmitted until receiving the XON condition from the receive MAC. The
pause counter will begin to decrement at then end of the current transmission, or immediately if no
transmission is underway. If another pause command is received while the transmitter is already in
pause, the new pause time indicated by the Flow Control packet will be loaded into the pause counter.
Revision 2.0 (02-14-13)
60
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
The pause function is enabled by either Auto-negotiation, or manually as discussed in Section 6.2.3,
"Flow Control Enable Logic," on page 58. Pause frames are consumed by the MAC and not sent to
the switch engine. Non-pause control frames are optionally filtered or forwarded.
When the receive FIFO is full and additional data continues to be received, an overrun condition occurs
and the frame is discarded (FIFO space recovered) or marked as a bad frame.
The receive MAC can be disabled from receiving all frames by clearing the RX Enable bit of the Port
x MAC Receive Configuration Register (MAC_RX_CFG_x).
The size of the RX FIFO is 256 bytes. If a bad packet with less than 64 bytes is received, it will be
flushed from the FIFO automatically and the FIFO space recovered. Packets equal to or larger than
64 bytes with an error will be marked and reported to the switch engine. The switch engine will
subsequently drop the packet.
6.3.1.1
Receive Counters
The receive MAC gathers statistics on each packet and increments the related counter registers. The
following receive counters are supported for each switch fabric port. Refer to Table 14.12, “Indirectly
Accessible Switch Control and Status Registers,” on page 308 and Section 14.5.2.3 through
Section 14.5.2.22 for detailed descriptions of these counters.

Total undersized packets (Section 14.5.2.3, on page 325)

Total packets 64 bytes in size (Section 14.5.2.4, on page 326)

Total packets 65 through 127 bytes in size (Section 14.5.2.5, on page 327)

Total packets 128 through 255 bytes in size (Section 14.5.2.6, on page 328)

Total packets 256 through 511 bytes in size (Section 14.5.2.7, on page 329)

Total packets 512 through 1023 bytes in size (Section 14.5.2.8, on page 330)

Total packets 1024 through maximum bytes in size (Section 14.5.2.9, on page 331)

Total oversized packets (Section 14.5.2.10, on page 332)

Total OK packets (Section 14.5.2.11, on page 333)

Total packets with CRC errors (Section 14.5.2.12, on page 334)

Total multicast packets (Section 14.5.2.13, on page 335)

Total broadcast packets (Section 14.5.2.14, on page 336)

Total MAC Pause packets (Section 14.5.2.15, on page 337)

Total fragment packets (Section 14.5.2.16, on page 338)

Total jabber packets (Section 14.5.2.17, on page 339)

Total alignment errors (Section 14.5.2.18, on page 340)

Total bytes received from all packets (Section 14.5.2.19, on page 341)

Total bytes received from good packets (Section 14.5.2.20, on page 342)

Total packets with a symbol error (Section 14.5.2.21, on page 343)

Total MAC control packets (Section 14.5.2.22, on page 344)
SMSC LAN9312
61
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
6.3.2
Transmit MAC
The transmit MAC generates an Ethernet MAC frame from TX FIFO data. This includes generating the
preamble and SFD, calculating and appending the frame checksum value, optionally padding
undersize packets to meet the minimum packet requirement size (64 bytes), and maintaining a
standard inter-frame gap time during transmit.
The transmit MAC can operate at 10/100Mbps, half- or full-duplex, and with or without flow control
depending on the state of the transmission. In half-duplex mode the transmit MAC meets CSMA/CD
IEEE 802.3 requirements. The transmit MAC will re-transmit if collisions occur during the first 64 bytes
(normal collisions), or will discard the packet if collisions occur after the first 64 bytes (late collisions).
The transmit MAC follows the standard truncated binary exponential back-off algorithm, collision and
jamming procedures.
The transmit MAC pre-pends the standard preamble and SFD to every packet from the FIFO. The
transmit MAC also follows as default, the standard Inter-Frame Gap (IFG). The default IFG is 96 bit
times and can be adjusted via the IFG Config field of the Port x MAC Transmit Configuration Register
(MAC_TX_CFG_x).
Packet padding and cyclic redundant code (FCS) calculation may be optionally performed by the
transmit MAC. The auto-padding process automatically adds enough zeros to packets shorter than 64
bytes. The auto-padding and FCS generation is controlled via the TX Pad Enable bit of the Port x MAC
Transmit Configuration Register (MAC_TX_CFG_x).
The transmit FIFO acts as a temporary buffer between the transmit MAC and the switch engine. The
FIFO logic manages the re-transmission for normal collision conditions or discards the frames for late
or excessive collisions.
When in full-duplex mode, the transmit MAC uses the flow-control algorithm specified in IEEE 802.3.
MAC pause frames are used primarily for flow control packets, which pass signalling information
between stations. MAC pause frames have a unique type of 8808h, and a pause op-code of 0001h.
The MAC pause frame contains the pause value in the data field. The flow control manager will autoadapt the procedure based on traffic volume and speed to avoid packet loss and unnecessary pause
periods.
When in half-duplex mode, the MAC uses a back pressure algorithm. The back pressure algorithm is
based on a forced collision and an aggressive back-off algorithm.
6.3.2.1
Transmit Counters
The transmit MAC gathers statistics on each packet and increments the related counter registers. The
following transmit counters are supported for each switch fabric port. Refer to Table 14.12, “Indirectly
Accessible Switch Control and Status Registers,” on page 308 and Section 14.5.2.25 through
Section 14.5.2.42 for detailed descriptions of these counters.

Total packets deferred (Section 14.5.2.25, on page 347)

Total pause packets (Section 14.5.2.26, on page 348)

Total OK packets (Section 14.5.2.27, on page 349)

Total packets 64 bytes in size (Section 14.5.2.28, on page 350)

Total packets 65 through 127 bytes in size (Section 14.5.2.29, on page 351)

Total packets 128 through 255 bytes in size (Section 14.5.2.30, on page 352)

Total packets 256 through 511 bytes in size (Section 14.5.2.31, on page 353)

Total packets 512 through 1023 bytes in size (Section 14.5.2.32, on page 354)

Total packets 1024 through maximum bytes in size (Section 14.5.2.33, on page 355)

Total undersized packets (Section 14.5.2.34, on page 356)

Total bytes transmitted from all packets (Section 14.5.2.35, on page 357)
Revision 2.0 (02-14-13)
62
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
6.4

Total broadcast packets (Section 14.5.2.36, on page 358)

Total multicast packets (Section 14.5.2.37, on page 359)

Total packets with a late collision (Section 14.5.2.38, on page 360)

Total packets with excessive collisions (Section 14.5.2.39, on page 361)

Total packets with a single collision (Section 14.5.2.40, on page 362)

Total packets with multiple collisions (Section 14.5.2.41, on page 363)

Total collision count (Section 14.5.2.42, on page 364)
Switch Engine (SWE)
The switch engine (SWE) is a VLAN layer 2 (link layer) switching engine supporting 3 ports. The SWE
supports the following types of frame formats: untagged frames, VLAN tagged frames, and priority
tagged frames. The SWE supports both the 802.3 and Ethernet II frame formats.
The SWE provides the control for all forwarding/filtering rules. It handles the address learning and
aging, and the destination port resolution based upon the MAC address and VLAN of the packet. The
SWE implements the standard bridge port states for spanning tree and provides packet metering for
input rate control. It also implements port mirroring, broadcast throttling, and multicast pruning and
filtering. Packet priorities are supported based on the IPv4 TOS bits and IPv6 Traffic Class bits using
a DIFFSERV Table mapping, the non-DIFFSERV mapped IPv4 precedence bits, VLAN priority using
a per port Priority Regeneration Table, DA based static priority, and Traffic Class mapping to one of 4
QoS transmit priority queues.
The following sections detail the various features of the switch engine.
6.4.1
MAC Address Lookup Table
The Address Logic Resolution (ALR) maintains a 1024 entry MAC Address Table. The ALR searches
the table for the destination MAC address. If the search finds a match, the associated data is returned
indicating the destination port or ports, whether to filter the packet, the packets priority (used if
enabled), and whether to override the ingress and egress spanning tree port state. Figure 6.3 displays
the ALR table entry structure. Refer to the Switch Engine ALR Write Data 0 Register
(SWE_ALR_WR_DAT_0) and Switch Engine ALR Write Data 1 Register (SWE_ALR_WR_DAT_1) for
detailed descriptions of these bits.
Bit
56
55
54
53
Valid
Age /
Override
Static
Filter
52
51
50
Priority
49
Port
48
47
...
0
MAC Address
Figure 6.3 ALR Table Entry Structure
SMSC LAN9312
63
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
6.4.1.1
Learning/Aging/Migration
The ALR adds new MAC addresses upon ingress along with the associated receive port.
If the source MAC address already exists, the entry is refreshed. This action serves two purposes.
First, if the source port has changed due to a network reconfiguration (migration), it is updated.
Second, each instance the entry is refreshed, the aging status bit is set, keeping the entry active.
Learning can be disabled per port via the Enable Learning on Ingress field of the Switch Engine Port
Ingress Configuration Register (SWE_PORT_INGRSS_CFG).
During each aging period, the ALR scans the learned MAC addresses. For entries which have the
aging status bit set, the ALR simply clears the bit. As mentioned above, if a MAC address is
subsequently refreshed, the aging bit will be set again and the process would repeat. If a learned entry
already had its aging status bit cleared (by a previous scan), the ALR will instead remove the learned
entry. Therefore, if two scans occur before a MAC address is refreshed, the entry will be aged and
removed. Each aging period is approximately 5 minutes. Therefore an entry will be aged and removed
at a minimum of 5 minutes, and a maximum of 10 minutes.
6.4.1.2
Static Entries
If a MAC address entry is manually added by the host CPU, it can be (and typically is) marked as
static. Static entries are not subjected to the aging process. Static entries also cannot be changed by
the learning process (including migration).
6.4.1.3
Multicast Pruning
The destination port that is returned as a result of a destination MAC address lookup may be a single
port or any combination of ports. The latter is used to setup multicast address groups. An entry with
a multicast MAC address would be entered manually by the host CPU with the appropriate destination
port(s). Typically, the Static bit should also be set to prevent automatic aging of the entry.
6.4.1.4
Address Filtering
Filtering can be performed on a destination MAC address. Such an entry would be entered manually
by the host CPU with the Filter bit active. Typically, the Static bit should also be set to prevent
automatic aging of the entry.
6.4.1.5
Spanning Tree Port State Override
A special spanning tree port state override setting can be applied to MAC address entries. When the
host CPU manually adds an entry with both the Static and Age bits set, packets with a matching
destination address will bypass the spanning tree port state and will be forwarded. This feature is
typically used to allow the reception of the BPDU packets while a port is in the non-forwarding state.
Refer to Section 6.4.5, "Spanning Tree Support," on page 70 for additional details.
6.4.1.6
MAC Destination Address Lookup Priority
If enabled in the Switch Engine Global Ingress Configuration Register
(SWE_GLOBAL_INGRSS_CFG), the transmit priority for static MAC address entries is taken from the
associated data of that entry.
6.4.1.7
Host Access
The ALR contains a learning engine that is used by the host CPU to add, delete, and modify the MAC
Address Table. This engine is accessed by using the Switch Engine ALR Command Register
(SWE_ALR_CMD), Switch Engine ALR Command Status Register (SWE_ALR_CMD_STS), Switch
Engine ALR Write Data 0 Register (SWE_ALR_WR_DAT_0), and Switch Engine ALR Write Data 1
Register (SWE_ALR_WR_DAT_1).
Revision 2.0 (02-14-13)
64
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
The following procedure should be followed in order to add, delete, and modify the ALR entries:
1. Write the Switch Engine ALR Write Data 0 Register (SWE_ALR_WR_DAT_0) and Switch Engine
ALR Write Data 1 Register (SWE_ALR_WR_DAT_1) with the desired MAC address and control
bits.
Note:An entry can be deleted by setting the Valid and Static bits to 0.
2. Write the Switch Engine ALR Command Register (SWE_ALR_CMD) register with 0004h (Make
Entry)
3. Poll the Make Pending bit in the Switch
(SWE_ALR_CMD_STS) until it is cleared.
Engine
ALR
Command
Status
Register
4. Write the Switch Engine ALR Command Register (SWE_ALR_CMD) with 0000h.
The ALR contains a search engine that is used by the host to read the MAC Address Table. This
engine is accessed by using the Switch Engine ALR Command Register (SWE_ALR_CMD), Switch
Engine ALR Read Data 0 Register (SWE_ALR_RD_DAT_0), and Switch Engine ALR Read Data 1
Register (SWE_ALR_RD_DAT_1).
Note: The entries read are not necessarily in the same order as they were learned or manually
added.
The following procedure should be followed in order to read the ALR entries:
1. Write the Switch Engine ALR Command Register (SWE_ALR_CMD) with 0002h (Get First Entry).
2. Write the Switch Engine ALR Command Register (SWE_ALR_CMD) with 0000h (Clear the Get
First Entry Bit)
3. Poll the Valid and End of Table bits in the Switch Engine ALR Read Data 1 Register
(SWE_ALR_RD_DAT_1) until either are set.
4. If the Valid bit is set, then the entry is valid and the data from the Switch Engine ALR Read Data
0 Register (SWE_ALR_RD_DAT_0) and Switch Engine ALR Read Data 1 Register
(SWE_ALR_RD_DAT_1) can be stored.
5. If the End of Table bit is set, then exit.
6. Write the Switch Engine ALR Command Register (SWE_ALR_CMD) with 0001h (Get Next Entry).
7. Write the Switch Engine ALR Command Register (SWE_ALR_CMD) with 0000h (Clear the Get
Next Entry bit)
8. Go to step 3.
Note: Refer to Section 14.5.3.1, on page 367 through Section 14.5.3.6, on page 374 for detailed
definitions of these registers.
SMSC LAN9312
65
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
6.4.2
Forwarding Rules
Upon ingress, packets are filtered or forwarded based on the following rules:

If the destination port equals the source port (local traffic), the packet is filtered.

If the source port is not in the forwarding state, the packet is filtered (unless the Spanning Tree
Port State Override is in effect).

If the destination port is not in the forwarding state, the packet is filtered (unless the Spanning Tree
Port State Override is in effect).

If the Filter bit for the Destination Address is set in the ALR table, the packet is filtered.

If the packet has a unicast destination MAC address which is not found in the ALR table and the
Drop Unknown bit is set, the packet is filtered.

If the packet has a multicast destination MAC address which is not found in the ALR table and the
Filter Multicast bit is set, the packet is filtered.

If the packet has a broadcast destination MAC address and the Broadcast Storm Control level has
been reached, the packet is discarded.

If Drop on Yellow is set, the packet is colored Yellow, and randomly selected, it is discarded.

If Drop on Red is set and the packet is colored Red, it is discarded.

If the destination address was not found in the ALR table (an unknown or a broadcast) and the
Broadcast Buffer Level is exceeded, the packet is discarded.

If there is insufficient buffer space, the packet is discarded.
When the switch is enabled for VLAN support, these following rules also apply:

If the packet is untagged or priority tagged and the Admit Only VLAN bit for the ingress port is set,
the packet is filtered.

If the packet is tagged and has a VID equal to FFFh, it is filtered.

If Enable Membership Checking on Ingress is set, Admit Non Member is cleared, and the source
port is not a member of the incoming VLAN, the packet is filtered.

If Enable Membership Checking on Ingress is set and the destination port is not a member of the
incoming VLAN, the packet is filtered.

If the destination address was not found in the ALR table (as unknown or broadcast) and the VLAN
broadcast domain containment resulted in zero valid destination ports, the packet is filtered.
Note: For the last three cases, if the VID is not in the VLAN table, the VLAN is considered foreign
and the membership result is NULL. A NULL membership will result in the packet being filtered
if Enable Membership Checking is set. A NULL membership will also result in the packet being
filtered if the destination address is not found in the ALR table (since the packet would have
no destinations).
Revision 2.0 (02-14-13)
66
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
6.4.3
Transmit Priority Queue Selection
The transmit priority queue may be selected from five options. As shown in Figure 6.4, the priority may
be based on:

the static value for the destination address in the ALR table

the precedence bits in the IPv4 TOS octet

the DIFFSERV mapping table indexed by the IPv4 TOS octet or the IPv6 Traffic Class octet

the VLAN tag priority field using the per port Priority Regeneration table

the port default
The last four options listed are sent through the Traffic Class table which maps the selected priority to
one of the four output queues. The static value from the ALR table directly specifies the queue.
Packet is from Host
Packet is Tagged
Packet is IPv 4
Packet is IP
VL Higher Priority
Use Precedence
Use IP
VLAN Enable
IPv4(TOS)
IPv6(TC)
6b
programmable
DIFFSERV table
3b
IPv4 Precedence
Source Port
VLAN Priority
ALR Priority
3b
2b
3b
programmable
port default
table
ALR Static Bit
DA Highest Priority
3b
priority
calculation
programmable
Traffic Class
table
static DA
override
2b
priority queue
3b
programmable
Priority
Regeneration
table
per port
2b
Figure 6.4 Switch Engine Transmit Queue Selection
SMSC LAN9312
67
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
The transmit queue priority is based on the packet type and device configuration as shown in
Figure 6.5 . Refer to Section 14.5.3.16, "Switch Engine Global Ingress Configuration Register
(SWE_GLOBAL_INGRSS_CFG)," on page 384 for definitions of the configuration bits.
Get Queue
Packet from Host
Y
N
DA Highest
Priority
N
Y
wait for ALR result
Y
ALR Static Bit
N
N
VL Higher
Priority
Y
VLAN Enable &
Packet is
Tagged
Y
N
Y
Packet is IPv 4/v6
& Use IP
N
Y
Packet is IPv 4
N
Y
Use Precedence
Resolved Priority =
IP Precedence
VLAN Enable &
Packet is
Tagged
Y
N
N
Resolved Priority =
DIFFSERV[TOS]
Resolved Priority =
DIFFSERV[TC]
Queue =
ALR Priority
Resolved Priority =
Default Priority[Source
Port]
Resolved Priority =
Priority Regen[VLAN
Priority]
Queue =
Traffic Class[Resolved Priority]
Get Queue Done
Figure 6.5 Switch Engine Transmit Queue Calculation
Revision 2.0 (02-14-13)
68
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
6.4.3.1
Port Default Priority
As detailed in Figure 6.5, the default priority is based on the ingress ports priority bits in its port VID
value. The PVID table is read and written by using the Switch Engine VLAN Command Register
(SWE_VLAN_CMD), Switch Engine VLAN Write Data Register (SWE_VLAN_WR_DATA), Switch
Engine VLAN Read Data Register (SWE_VLAN_RD_DATA), and Switch Engine VLAN Command
Status Register (SWE_VLAN_CMD_STS). Refer to Section 14.5.3.8, on page 376 through Section
14.5.3.11, on page 379 for detailed VLAN register descriptions.
6.4.3.2
IP Precedence Based Priority
The transmit priority queue can be chosen based on the Precedence bits of the IPv4 TOS octet. This
is supported for tagged and non-tagged packets for both type field and length field encapsulations. The
Precedence bits are the three most significant bits of the IPv4 TOS octet.
6.4.3.3
DIFFSERV Based Priority
The transmit priority queue can be chosen based on the DIFFSERV usage of the IPv4 TOS or IPv6
Traffic Class octet. This is supported for tagged and non-tagged packets for both type field and length
field encapsulations.
The DIFFSERV table is used to determine the packet priority from the 6-bit Differentiated Services (DS)
field. The DS field is defined as the six most significant bits of the IPv4 TOS octet or the IPv6 Traffic
Class octet and is used as an index into the DIFFSERV table. The output of the DIFFSERV table is
then used as the priority. This priority is then passed through the Traffic Class table to select the
transmit priority queue.
Note: The DIFFSERV table is not initialized upon reset or power-up. If DIFFSERV is enabled, then
the full table must be initialized by the host.
The DIFFSERV table is read and written by using the Switch Engine DIFFSERV Table Command
Register (SWE_DIFFSERV_TBL_CFG), Switch Engine DIFFSERV Table Write Data Register
(SWE_DIFFSERV_TBL_WR_DATA), Switch Engine DIFFSERV Table Read Data Register
(SWE_DIFFSERV_TBL_RD_DATA), and Switch Engine DIFFSERV Table Command Status Register
(SWE_DIFFSERV_TBL_CMD_STS). Refer to Section 14.5.3.12, on page 380 through Section
14.5.3.15, on page 383 for detailed DIFFSERV register descriptions.
6.4.3.4
VLAN Priority
As detailed in Figure 6.5, the transmit priority queue can be taken from the priority field of the VLAN
tag. The VLAN priority is sent through a per port Priority Regeneration table, which is used to map the
VLAN priority into a user defined priority.
The Priority Regeneration table is programmed by using the Switch Engine Port 0 Ingress VLAN
Priority Regeneration Table Register (SWE_INGRSS_REGEN_TBL_MII), Switch Engine Port 1 Ingress
VLAN Priority Regeneration Table Register (SWE_INGRSS_REGEN_TBL_1), and Switch Engine Port
2 Ingress VLAN Priority Regeneration Table Register (SWE_INGRSS_REGEN_TBL_2). Refer to
Section 14.5.3.33, on page 403 through Section 14.5.3.35, on page 405 for detailed descriptions of
these registers.
SMSC LAN9312
69
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
6.4.4
VLAN Support
The switch engine supports 16 active VLANs out of a possible 4096. The VLAN table contains the 16
active VLAN entries, each consisting of the VID, the port membership, and un-tagging instructions.
17
16
15
14
13
12
Member
Port 2
Un-tag
Port 2
Member
Port 1
Un-tag
Port 1
Member
MII
Un-tag
MII
11
...
0
VID
Figure 6.6 VLAN Table Entry Structure
On ingress, if a packet has a VLAN tag containing a valid VID (not 000h or FFFh), the VID table is
searched. If the VID is found, the VLAN is considered active and the membership and un-tag
instruction is used. If the VID is not found, the VLAN is considered foreign and the membership result
is NULL. A NULL membership will result in the packet being filtered if Enable Membership Checking
is set. A NULL membership will also result in the packet being filtered if the destination address is not
found in the ALR table (since the packet would have no destinations).
On ingress, if a packet does not have a VLAN tag or if the VLAN tag contains VID with a value of 0
(priority tag), the packet is assigned a VLAN based on the Port Default VID (PVID) and Priority. The
PVID is then used to access the above VLAN table.
The VLAN membership of the packet is used for ingress and egress checking and for VLAN broadcast
domain containment. The un-tag instructions are used at egress on ports defined as hybrid ports.
Refer to Section 14.5.3.8, on page 376 through Section 14.5.3.11, on page 379 for detailed VLAN
register descriptions.
6.4.5
Spanning Tree Support
Hardware support for the Spanning Tree Protocol (STP) and the Rapid Spanning Tree Protocol (RSTP)
includes a per port state register as well as the override bit in the MAC Address Table entries (Section
6.4.1.5, on page 64) and the host CPU port special tagging (Section 6.4.10, on page 75).
The Switch Engine Port State Register (SWE_PORT_STATE) is used to place a port into one of the
modes as shown in Table 6.2. Normally only Port 1 and Port 2 are placed into modes other than
forwarding. Port 0 should normally be left in forwarding mode.
Table 6.2 Spanning Tree States
Port State
01 - Blocking
(also used for
disabled)
Hardware Action
Software Action
Received packets on the port are
discarded.
Transmissions to the port are blocked.
Learning on the port is disabled.
The MAC Address Table should be programmed
with entries that the host CPU needs to receive
(e.g. the BPDU address). The static and override
bits should be set.
The host CPU should not send any packets to the
port in this state.
The host CPU should discard received packets
from this port when in the Disabled state.
Note:
Revision 2.0 (02-14-13)
70
DATASHEET
There is no hardware distinction between
the Blocking and Disabled states.
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 6.2 Spanning Tree States (continued)
Port State
11 - Listening
Hardware Action
Software Action
Received packets on the port are
discarded.
Transmissions to the port are blocked.
10 - Learning
Learning on the port is disabled.
The host CPU may send packets to the port in this
state.
Received packets on the port are
discarded.
The MAC Address Table should be programmed
with entries that the host CPU needs to receive
(e.g. the BPDU address). The static and override
bits should be set.
Transmissions to the port are blocked.
00 - Forwarding
Learning on the port is enabled.
The host CPU may send packets to the port in this
state.
Received packets on the port are
forwarded normally.
The MAC Address Table should be programmed
with entries that the host CPU needs to receive
(e.g. the BPDU address). The static and override
bits should be set.
Transmissions to the port are sent
normally.
The host CPU may send packets to the port in this
state.
Learning on the port is enabled.
6.4.6
The MAC Address Table should be programmed
with entries that the host CPU needs to receive
(e.g. the BPDU address). The static and override
bits should be set.
Ingress Flow Metering and Coloring
The LAN9312 supports hardware ingress rate limiting by metering packet streams and marking packets
as either Green, Yellow, or Red according to three traffic parameters: Committed Information Rate
(CIR), Committed Burst Size (CBS), and Excess Burst Size (EBS). A packet is marked Green if it does
not exceed the CBS, Yellow if it exceeds to CBS but not the EBS, or Red otherwise.
Ingress flow metering and coloring is enabled via the Ingress Rate Enable bit in the Switch Engine
Ingress Rate Configuration Register (SWE_INGRSS_RATE_CFG). Once enabled, each incoming
packet is classified into a stream. Streams are defined as per port (3 streams), per priority (8 streams),
or per port & priority (24 streams) as selected via the Rate Mode bits in the Switch Engine Ingress
Rate Configuration Register (SWE_INGRSS_RATE_CFG). Each stream can have a different CIR
setting. All streams share common CBS and EBS settings. CIR, CBS, and EBS are programmed via
the Switch Engine Ingress Rate Command Register (SWE_INGRSS_RATE_CMD) and Switch Engine
Ingress Rate Write Data Register (SWE_INGRSS_RATE_WR_DATA).
Each stream is metered according to RFC 2697. At the rate set by the CIR, two token buckets are
credited per stream. First, the Committed Burst bucket is incremented up to the maximum set by the
CBS. Once the Committed Burst bucket is full, the Excess Burst bucket is incremented up to the
maximum set by the EBS. The CIR rate is specified in time per byte. The value programmed is in
approximately 20 nS per byte increments. Typical values are listed in Table 6.3. When a port is
receiving at 10Mbps, any setting faster than 39 has the effect of not limiting the rate.
SMSC LAN9312
71
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 6.3 Typical Ingress Rate Settings
CIR Setting
Time Per Byte
Bandwidth
0-3
80 nS
100 Mbps
4
100 nS
80 Mbps
5
120 nS
67 Mbps
6
140 nS
57 Mbps
7
160 nS
50 Mbps
9
200 nS
40 Mbps
12
260 nS
31 Mbps
19
400 nS
20 Mbps
39
800 nS
10 Mbps
79
1600 nS
5 Mbps
160
3220 nS
2.5 Mbps
402
8060 nS
1 Mbps
804
16100 nS
500 Kbps
1610
32220 nS
250 Kbps
4028
80580 nS
100 Kbps
8056
161140 nS
50 Kbps
After each packet is received, the bucket is decremented. If the Committed Burst bucket has sufficient
tokens, it is debited and the packet is colored Green. If the Committed Burst bucket lacks sufficient
tokens for the packet, the Excess Burst bucket is checked. If the Excess Burst bucket has sufficient
tokens, it is debited, the packet is colored Yellow and is subjected to random discard. If the Excess
Burst bucket lacks sufficient tokens for the packet, the packet is colored Red and is discarded.
Note: All of the token buckets are initialized to the default value of 1536. If lower values are
programmed into the CBS and EBS parameters, the token buckets will need to be normally
depleted below these values before the values have any affect on limiting the maximum value
of the token buckets.
Refer to Section 14.5.3.25, on page 394 through Section 14.5.3.29, on page 399 for detailed register
descriptions.
6.4.6.1
Ingress Flow Calculation
Based on the flow monitoring mode, an ingress flow definition can include the ingress priority. This is
calculated similarly to the transmit queue with the exception that the Priority Regeneration and the
Traffic Class table are not used. As shown in Figure 6.7, the priority can be based on:

The precedence bits in the IPv4 TOS octet

The DIFFSERV mapping table indexed by the IPv4 TOS octet or the IPv6 Traffic Class octet

The VLAN tag priority field (but not through the per port Priority Regeneration table)

The port default
Revision 2.0 (02-14-13)
72
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Packet is from Host
Packet is Tagged
Packet is IPv 4
Packet is IP
VL Higher Priority
Use Precedence
Use IP
VLAN Enable
6b
IPv4(TOS)
IPv6(TC)
Programmable
DIFFSERV Table
3b
IPv4 Precedence
3b
Priority
Calculation
3b
flow priority
Programmable
Port Default
Table
2b
Source Port
3b
3b
VLAN Priority
Figure 6.7 Switch Engine Ingress Flow Priority Selection
The ingress flow calculation is based on the packet type and the device configuration as shown in
Figure 6.8.
Get Flow Priority
Packet from Host
Y
N
N
VL Higher
Priority
Y
Vlan Enable &
Packet is
Tagged
Y
N
Y
Packet is IPv 4/v6
& Use IP
N
Y
Vlan Enable &
Packet is
Tagged
Packet is IPv 4
N
Y
Use Precedence
Flow Priority =
IP Precedence
Y
N
N
Flow Priority =
DIFFSERV[TOS]
Flow Priority =
DIFFSERV[TC]
Flow Priority =
Default Priority[Source
Port]
Flow Priority =
VLAN Priority
Get Flow Priority Done
Figure 6.8 Switch Engine Ingress Flow Priority Calculation
SMSC LAN9312
73
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
6.4.7
Broadcast Storm Control
In addition to ingress rate limiting, the LAN9312 supports hardware broadcast storm control on a per
port basis. This feature is enabled via the Switch Engine Broadcast Throttling Register
(SWE_BCST_THROT). The allowed rate per port is specified as the number of bytes multiplied by 64
allowed to be received every 1.72 mS interval. Packets that exceed this limit are dropped. Typical
values are listed in Table 6.4. When a port is receiving at 10Mbps, any setting above 34 has the effect
of not limiting the rate.
Table 6.4 Typical Broadcast Rate Settings
Broadcast Throttle Level
Bandwidth
252
75 Mbps
168
50 Mbps
134
40 Mbps
67
20 Mbps
34
10 Mbps
17
5 Mbps
8
2.4 Mbps
4
1.2 Mbps
3
900 Kbps
2
600 Kbps
1
300 Kbps
In addition to the rate limit, the Buffer Manager Broadcast Buffer Level Register (BM_BCST_LVL)
specifies the maximum number of buffers that can be used by broadcasts, multicasts, and unknown
unicasts.
6.4.8
IPv4 IGMP Support
The LAN9312 provides Internet Group Management Protocol (IGMP) hardware support using two
mechanisms: IGMP monitoring and Multicast Pruning.
On ingress, if IGMP packet monitoring is enabled in the Switch Engine Global Ingress Configuration
Register (SWE_GLOBAL_INGRSS_CFG), IGMP multicast packets are trapped and redirected to the
IGMP monitoring port (typically set to the port to which the host CPU is connected). IGMP packets are
identified as IPv4 packets with a protocol of 2. Both Ethernet and IEEE 802.3 frame formats are
supported as are VLAN tagged packets.
Once the IGMP packets are received by the host CPU, the host software can decide which port or
ports need to be members of the multicast group. This group is then added to the ALR table as detailed
in Section 6.4.1.3, "Multicast Pruning," on page 64. The host software should also forward the original
IGMP packet if necessary.
Normally, packets are never transmitted back to the receiving port. For IGMP monitoring, this may
optionally be enabled via the Switch Engine Global Ingress Configuration Register
(SWE_GLOBAL_INGRSS_CFG). This function would be used if the monitoring port wished to
participate in the IGMP group without the need to perform special handling in the transmit portion of
the driver software.
Revision 2.0 (02-14-13)
74
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Note: Most forwarding rules are skipped when a packet is monitored. However, a packet is still filtered
if:
The
source port is not in the forwarding state (unless Spanning Tree Port State Override is in
effect.
VLAN’s
are enabled, the packet is untagged or priority tagged, and the Admit Only VLAN bit
for the ingress port is set.
VLAN’s
are enabled and the packet is tagged and had a VID equal to FFFh.
VLAN’s
are enabled, Enabled Membership Checking on Ingress is set, Admit Non Member is
cleared, and the source port is not a member of the incoming VLAN.
6.4.9
Port Mirroring
The LAN9312 supports port mirroring where packets received or transmitted on a port or ports can
also be copied onto another “sniffer” port.
Port mirroring is configured using the Switch Engine Port Mirroring Register (SWE_PORT_MIRROR).
Multiple mirrored ports can be defined, but only one sniffer port can be defined.
When receive mirroring is enabled, packets that are forwarded from a port designated as a mirrored
port are also transmitted by the sniffer port. For example, Port 2 is setup to be a mirrored port and
Port 0 is setup to be the sniffer port. If a packet is received on Port 2 with a destination of Port 1, it
is forwarded to both Port 1 and Port 0.
When transmit mirroring is enabled, packets that are forwarded to a port designated as a mirrored port
are also transmitted by the sniffer port. For example, Port 2 is setup to be a mirrored port and Port 0
is setup to be the sniffer port. If a packet is received on Port 1 with a destination of Port 2, it is
forwarded to both Port 2 and Port 0.
Note: A packet will never be transmitted out of the receiving port. A receive packet is not normally
mirrored if it is filtered. This can optionally be enabled.
6.4.10
Host CPU Port Special Tagging
The Switch Engine Ingress Port Type Register (SWE_INGRSS_PORT_TYP) and Buffer Manager
Egress Port Type Register (BM_EGRSS_PORT_TYPE) are used to enable a special VLAN tag that is
used by the host CPU. This special tag is used to specify the port(s) where packets from the CPU
should be sent, and to indicate which port received the packet that was forwarded to the CPU.
6.4.10.1
Packets from the Host CPU
The Switch Engine Ingress Port Type Register (SWE_INGRSS_PORT_TYP) configures the switch to
use the special VLAN tag in packets from the host CPU as a destination port indicator. A setting of
11b should be used on the port that is connected to the host CPU (typically Port 0). A setting of 00b
should be used on the normal network ports.
The special VLAN tag is a normal VLAN tag where the VID field is used as the destination port
indicator. If VID bit 3 is zero, then bits 0 and 1 specify the destination port (0, 1, 2) or broadcast (3).
If VID bit 3 is one, then the normal ALR lookup is performed and learning is performed on the source
address. The PRI field from the VLAN tag is used as the packet priority.
Upon egress from the destination port(s), the special tag is removed. If a regular VLAN tag needs to
be sent as part of the packet, then it should be part of the packet data from the host CPU port or set
as an unused bit in the VID field.
Note: When specifying Port 0 as the destination port, the VID will be set to 0. A VID of 0 is normally
considered a priority tagged packet. Such a packet will be filtered if Admit Only VLAN is set
on the host CPU port. Either avoid setting Admit Only VLAN on the host CPU port or set an
unused bit in the VID field.
SMSC LAN9312
75
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Note: The maximum size tagged packet that can normally be sent into a switch port (from the Host
MAC) is 1522 bytes. Since the special tag consumes four bytes of the packet length, the
outgoing packet is limited to 1518 bytes, even if it contains a regular VLAN tag as part of the
packet data. If a larger outgoing packet is required, the Jumbo2K bit in the Port x MAC Receive
Configuration Register (MAC_RX_CFG_x) of Port 0 should be set.
6.4.10.2
Packets to the Host CPU
The Buffer Manager Egress Port Type Register (BM_EGRSS_PORT_TYPE) configures the switch to
add the special VLAN tag in packets to the host CPU as a source port indicator. A setting of 11b should
be used only on the port that is connected to the host CPU (typically Port 0). Other settings can be
used on the normal network ports as needed.
The special VLAN tag is a normal VLAN tag where bits 0 and 1 of the VID field specify the source
port (0, 1, or 2).
Upon egress from the host CPU port, the special tag is added. If a regular VLAN tag already exists,
it is not deleted. Instead it will follow the special tag.
Note: Since the special tag adds four bytes to the length of the packet, it is possible for a normally
tagged, maximum size, incoming packet to become 1526 bytes in length. In order for the Host
MAC to receive this length packet without indicating a length error, the Host MAC VLAN2 Tag
Register (HMAC_VLAN2) in the Host MAC should be set to 8100h and the Host MAC VLAN1
Tag Register (HMAC_VLAN1) should be set to a value other than 8100h. This configuration
will allow frames up to 1538 bytes in length to be received.
Note: Since the special tag adds four bytes to the length of the packet, it is possible for a normally
tagged, maximum size, incoming jumbo packet to become 2052 bytes in length. This packet
will be received by the Host MAC with the following conditions:
The
receive status will indicate Frame Too Long
Up
to four bytes of the end of packet may be truncated (the maximum receive length at the
Host MAC is 2048).
6.4.11
Counters
A counter is maintained per port that contains the number of MAC address that were not learned or
were overwritten by a different address due to MAC Address Table space limitations. These counters
are accessible via the following registers:

Switch Engine Port 0 Learn Discard Count Register (SWE_LRN_DISCRD_CNT_MII)

Switch Engine Port 1 Learn Discard Count Register (SWE_LRN_DISCRD_CNT_1)

Switch Engine Port 2 Learn Discard Count Register (SWE_LRN_DISCRD_CNT_2)
A counter is maintained per port that contains the number of packets filtered at ingress. This count
includes packets filtered due to broadcast throttling, but does not include packets dropped due to
ingress rate limiting. These counters are accessible via the following registers:

Switch Engine Port 0 Ingress Filtered Count Register (SWE_FILTERED_CNT_MII)

Switch Engine Port 1 Ingress Filtered Count Register (SWE_FILTERED_CNT_1)

Switch Engine Port 2 Ingress Filtered Count Register (SWE_FILTERED_CNT_2)
Revision 2.0 (02-14-13)
76
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
6.5
Buffer Manager (BM)
The buffer manager (BM) provides control of the free buffer space, the multiple priority transmit
queues, transmission scheduling, and packet dropping. VLAN tag insertion and removal is also
performed by the buffer manager. The following sections detail the various features of the buffer
manager.
6.5.1
Packet Buffer Allocation
The packet buffer consists of 32KB of RAM that is dynamically allocated in 128 byte blocks as packets
are received. Up to 16 blocks may be used per packet, depending on the packet length. The blocks
are linked together as the packet is received. If a packet is filtered, dropped, or contains a receive
error, the buffers are reclaimed.
6.5.1.1
Buffer Limits and Flow Control Levels
The BM keeps track of the amount of buffers used per each ingress port. These counts are used to
generate flow control (half-duplex backpressure or full-duplex pause frames) and to limit the amount
of buffer space that can be used by any individual receiver (hard drop limit). The flow control and drop
limit thresholds are dynamic and adapt based on the current buffer usage. Based on the number of
active receiving ports, the drop level and flow control pause and resume thresholds adjust between
fixed settings and two user programmable levels via the Buffer Manager Drop Level Register
(BM_DROP_LVL), Buffer Manager Flow Control Pause Level Register (BM_FC_PAUSE_LVL), and
Buffer Manager Flow Control Resume Level Register (BM_FC_RESUME_LVL) respectively.
The BM also keeps a count of the number of buffers that are queued for multiple ports (broadcast
queue). This count is compared against the Buffer Manager Broadcast Buffer Level Register
(BM_BCST_LVL), and if the configured drop level is reached or exceeded, subsequent packets are
dropped.
6.5.2
Random Early Discard (RED)
Based on the ingress flow monitoring detailed in Section 6.4.6, "Ingress Flow Metering and Coloring,"
on page 71, packets are colored as Green, Yellow, or Red. Packets colored Red are always discarded
if the Drop on Red bit in the Buffer Manager Configuration Register (BM_CFG) is set. If the Drop on
Yellow bit in the Buffer Manager Configuration Register (BM_CFG) is set, packets colored Yellow are
randomly discarded based on the moving average number of buffers used by the ingress port.
The probability of a discard is programmable into the Random Discard Weight table via the Buffer
Manager Random Discard Table Command Register (BM_RNDM_DSCRD_TBL_CMD), Buffer
Manager Random Discard Table Write Data Register (BM_RNDM_DSCRD_TBL_WDATA), and Buffer
Manager Random Discard Table Read Data Register (BM_RNDM_DSCRD_TBL_RDATA). The
Random Discard Weight table contains sixteen entries, each 10-bits wide. Each entry corresponds to
a range of the average number of buffers used by the ingress port. Entry 0 is for 0 to 15 buffers, entry
1 is for 16 to 31 buffers, etc. The probability for each entry us set in 1/1024’s. For example, a setting
of 1 is 1-in-1024, or approximately 0.1%. A setting of all ones (1023) is 1023-in-1024, or approximately
99.9%.
Refer to Section 14.5.4.10, "Buffer Manager Random Discard Table Command Register
(BM_RNDM_DSCRD_TBL_CMD)," on page 421 for additional details on writing and reading the
Random Discard Weight table.
6.5.3
Transmit Queues
Once a packet has been completely received, it is queued for transmit. There are four queues per
transmit port, one for each level of transmit priority. Each queue is virtual (if there are no packets for
that port/priority, the queue is empty), and dynamic (a queue may be any length if there is enough
memory space). When a packet is read from the memory and sent out to the corresponding port, the
used buffers are released.
SMSC LAN9312
77
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
6.5.4
Transmit Priority Queue Servicing
When a transmit queue is non-empty, it is serviced and the packet is read from the buffer RAM and
sent to the transmit MAC. If there are multiple queues that require servicing, one of two methods may
be used: fixed priority ordering, or weighted round-robin ordering. If the Fixed Priority Queue Servicing
bit in the Buffer Manager Configuration Register (BM_CFG) is set, a strict order, fixed priority is
selected. Transmit queue 3 has the highest priority, followed by 2, 1, and 0. If the Fixed Priority Queue
Servicing bit in the Buffer Manager Configuration Register (BM_CFG) is cleared, a weighted roundrobin order is followed. Assuming all four queues are non-empty, the service is weighted with a 9:4:2:1
ratio (queue 3,2,1,0). The servicing is blended to avoid burstiness (e.g. queue 3, then queue 2, then
queue 3, etc.).
6.5.5
Egress Rate Limiting (Leaky Bucket)
For egress rate limiting, the leaky bucket algorithm is used on each output priority queue. For each
output port, the bandwidth that is used by each priority queue can be limited. If any egress queue
receives packets faster than the specified egress rate, packets will be accumulated in the packet
memory. After the memory is used, packet dropping or flow control will be triggered.
Note: Egress rate limiting occurs before the Transmit Priority Queue Servicing, such that a lower
priority queue will be serviced if a higher priority queue is being rate limited.
The egress limiting is enabled per priority queue. After a packet is selected to be sent, its length is
recorded. The switch then waits a programmable amount of time, scaled by the packet length, before
servicing that queue once again. The amount of time per byte is programmed into the Buffer Manager
Egress Rate registers (refer to Section 14.5.4.14 through Section 14.5.4.19 for detailed register
definitions). The value programmed is in approximately 20 nS per byte increments. Typical values are
listed in Table 6.5. When a port is transmitting at 10 Mbps, any setting above 39 has the effect of not
limiting the rate.
Table 6.5 Typical Egress Rate Settings
EGRESS RATE
SETTING
TIME PER BYTE
BANDWIDTH @
64 BYTE PACKET
BANDWIDTH @
512 BYTE PACKET
BANDWIDTH @
1518 BYTE PACKET
0-3
80 nS
76 Mbps (Note 6.3)
96 Mbps (Note 6.3)
99 Mbps (Note 6.3)
4
100 nS
66 Mbps
78 Mbps
80 Mbps
5
120 nS
55 Mbps
65 Mbps
67 Mbps
6
140 nS
48 Mbps
56 Mbps
57 Mbps
7
160 nS
42 Mbps
49 Mbps
50 Mbps
9
200 nS
34 Mbps
39 Mbps
40 Mbps
12
260 nS
26 Mbps
30 Mbps
31 Mbps
19
400 nS
17 Mbps
20 Mbps
20 Mbps
39
800 nS
8.6 Mbps
10 Mbps
10 Mbps
78
1580 nS
4.4 Mbps
5 Mbps
5 Mbps
158
3180 nS
2.2 Mbps
2.5 Mbps
2.5 Mbps
396
7940 nS
870 Kbps
990 Kbps
1 Mbps
794
15900 nS
440 Kbps
490 Kbps
500 Kbps
1589
31800 nS
220 Kbps
250 Kbps
250 Kbps
3973
79480 nS
87 Kbps
98 Kbps
100 Kbps
7947
158960 nS
44 Kbps
49 Kbps
50 Kbps
Revision 2.0 (02-14-13)
78
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Note 6.3
6.5.6
These are the unlimited max bandwidths when IFG and preamble are taken into account.
Adding, Removing, and Changing VLAN Tags
Based on the port configuration and the received packet formation, a VLAN tag can be added to,
removed from, or modified in a packet. There are four received packet type cases: non-tagged, prioritytagged, normal-tagged, and CPU special-tagged. There are also four possible settings for an egress
port: dumb, access, hybrid, and CPU. In addition, each VLAN table entry can specify the removal of
the VLAN tag (the entry’s un-tag bit).
The tagging/un-tagging rules are specified as follows:

Dumb Port - This port type generally does not change the tag.
When a received packet is non-tagged, priority-tagged, or normal-tagged, the packet passes
untouched.
When a packet is received special-tagged from a CPU port, the special tag is removed.

Access Port - This port type generally does not support tagging.
When a received packet in non-tagged, the packet passes untouched.
When a received packet is priority-tagged or normal-tagged, the tag is removed.
When a received packet is special-tagged from a CPU port, the special tag is removed.

CPU Port - Packets transmitted from this port type generally contain a special tag. Special tags
are described in detail in Section 6.4.10, "Host CPU Port Special Tagging," on page 75.

Hybrid Port - Generally, this port type supports a mix of normal-tagged and non-tagged packets.
It is the most complex, but most flexible port type.
For clarity, the following details the incoming un-tag instruction. As described in Section 6.4.4, "VLAN
Support," on page 70, the un-tag instruction is one of three un-tag bits from the applicable entry in the
VLAN table, selected by the ingress port number. The entry in the VLAN table is either the VLAN from
the received packet or the ingress ports default VID.

When a received packet is non-tagged, a new VLAN tag is added if two conditions are met. First,
the Insert Tag bit for the egress port in the Buffer Manager Egress Port Type Register
(BM_EGRSS_PORT_TYPE) must be set. Second, the un-tag instruction associated with the
ingress ports default VID must be cleared. The VLAN tag that is added will have a VID and Priority
taken from the ingress ports default VID and priority.

When a received packet is priority-tagged, either the tag is removed or it is modified.
If the un-tag instruction associated with the ingress ports default VID is set, then the tag is removed.
Otherwise, the tag is modified. The VID of the new VLAN tag is changed to the ingress ports default
VID. If the Change Priority bit in the Buffer Manager Egress Port Type Register
(BM_EGRSS_PORT_TYPE) for the egress port is set, then the Priority field of the new VLAN tag
is also changed to the ingress ports default priority.

When a received packet is normal-tagged, either the tag is removed, modified, or passed.
If the un-tag instruction associated with the VID in the received packet is set, then the tag is
removed.
Else, if the Change Tag bit in the Buffer Manager Egress Port Type Register
(BM_EGRSS_PORT_TYPE) for the egress port is clear, the packet is untouched.
Else, if both the Change VLAN ID and the Change Priority bits in the Buffer Manager Egress Port
Type Register (BM_EGRSS_PORT_TYPE) for the egress port are clear, the packet passes
untouched.
Otherwise, the tag is modified. If the Change VLAN ID bit for the egress port is set, the VOD of
the new VLAN tag is changed to the egress ports default ID. If the Change Priority bit for the egress
port is set, the Priority field of the new VLAN is changed to the egress ports default priority.

When a packet is received special-tagged from a CPU port, the special tag is removed.
SMSC LAN9312
79
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Hybrid tagging is summarized in Figure 6.9.
Receive Tag
Type
Non-tagged
Insert Tag
[egress_port]
Normal Tagged Priority Tagged
Default VID
[ingress_port]
Un-tag Bit
N
Y
Special Tagged
Y
N
Default VID
[ingress_port]
Un-tag Bit
Change Priority
[egress_port]
Y
N
N
Y
Add Tag
VID = Default VID
[ingress_port]
Priority = Default Priority
[ingress_port]
Modify Tag
VID = Default VID
[ingress_port]
Priority = Default Priority
[ingress_port]
Send Packet Untouched
Received VID
Un-tag Bit
Modify Tag
VID = Default VID
[ingress_port]
Priority = Unchanged
Strip Tag
Strip Tag
Y
N
Change Tag
[egress_port]
N
Y
Y
Change Priority
[egress_port]
Y
Modify Tag
VID = Default VID
[egress_port]
Priority = Default Priority
[egress_port]
Change VLAN ID
[egress_port]
N
N
Y
Modify Tag
VID = Default VID
[egress_port]
Priority = Unchanged
Change Priority
[egress_port]
Modify Tag
VID = Unchanged
Priority = Default Priority
[egress_port]
N
Send Packet Untouched
Strip Tag
Figure 6.9 Hybrid Port Tagging and Un-tagging
The default VLAN ID and priority of each port may be configured via the following registers:

Buffer Manager Port 0 Default VLAN ID and Priority Register (BM_VLAN_MII)

Buffer Manager Port 1 Default VLAN ID and Priority Register (BM_VLAN_1)

Buffer Manager Port 2 Default VLAN ID and Priority Register (BM_VLAN_2)
Revision 2.0 (02-14-13)
80
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
6.5.7
Counters
A counter is maintained per port that contains the number of packets dropped due to buffer space limits
and ingress rate limit discarding (Red and random Yellow dropping). These counters are accessible
via the following registers:

Buffer Manager Port 0 Drop Count Register (BM_DRP_CNT_SRC_MII)

Buffer Manager Port 1 Drop Count Register (BM_DRP_CNT_SRC_1)

Buffer Manager Port 2 Drop Count Register (BM_DRP_CNT_SRC_2)
A counter is maintained per port that contains the number of packets dropped due solely to ingress
rate limit discarding (Red and random Yellow dropping). This count value can be subtracted from the
drop counter, as described above, to obtain the drop counts due solely to buffer space limits. The
ingress rate drop counters are accessible via the following registers:
6.6

Buffer Manager Port 0 Ingress Rate Drop Count Register (BM_RATE_DRP_CNT_SRC_MII)

Buffer Manager Port 1 Ingress Rate Drop Count Register (BM_RATE_DRP_CNT_SRC_1)

Buffer Manager Port 2 Ingress Rate Drop Count Register (BM_RATE_DRP_CNT_SRC_2)
Switch Fabric Interrupts
The switch fabric is capable of generating multiple maskable interrupts from the buffer manager, switch
engine, and MACs. These interrupts are detailed in Section 5.2.2, "Switch Fabric Interrupts," on
page 51.
SMSC LAN9312
81
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 7 Ethernet PHYs
7.1
Functional Overview
The LAN9312 contains three PHYs: Port 1 PHY, Port 2 PHY and a Virtual PHY. The Port 1 & 2 PHYs
are identical in functionality and each connect their corresponding Ethernet signal pins to the switch
fabric MAC of their respective port. These PHYs interface with their respective MAC via an internal MII
interface. The Virtual PHY provides the virtual functionality of a PHY and allows connection of the Host
MAC to port 0 of the switch fabric as if it was connected to a single port PHY. All PHYs comply with
the IEEE 802.3 Physical Layer for Twisted Pair Ethernet and can be configured for full/half duplex 100
Mbps (100BASE-TX) or 10Mbps (10BASE-T) Ethernet operation. All PHY registers follow the IEEE
802.3 (clause 22.2.4) specified MII management register set and can be configured indirectly via the
Host MAC, or directly via the memory mapped Virtual PHY registers. Refer to Section 14.4, "Ethernet
PHY Control and Status Registers" for details on the Ethernet PHY registers.
The LAN9312 Ethernet PHYs are discussed in detail in the following sections:
7.1.1

Section 7.2, "Port 1 & 2 PHYs," on page 83

Section 7.3, "Virtual PHY," on page 96
PHY Addressing
Each individual PHY is assigned a unique default PHY address via the phy_addr_sel_strap
configuration strap as shown in Table 7.1. In addition, the Port 1 PHY and Port 2 PHY addresses can
be changed via the PHY Address (PHYADD) field in the Port x PHY Special Modes Register
(PHY_SPECIAL_MODES_x). For proper operation, all LAN9312 PHY addresses must be unique. No
check is performed to assure each PHY is set to a different address. Configuration strap values are
latched upon the de-assertion of a chip-level reset as described in Section 4.2.4, "Configuration
Straps," on page 40.
Table 7.1 Default PHY Serial MII Addressing
PHY_ADDR_SEL_STRAP
VIRTUAL PHY DEFAULT
ADDRESS VALUE
PORT 1 PHY DEFAULT
ADDRESS VALUE
PORT 2 PHY DEFAULT
ADDRESS VALUE
0
0
1
2
1
1
2
3
Revision 2.0 (02-14-13)
82
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
7.2
Port 1 & 2 PHYs
Functionally, each PHY can be divided into the following sections:

100BASE-TX Transmit and 100BASE-TX Receive

10BASE-T Transmit and 10BASE-T Receive

PHY Auto-negotiation

HP Auto-MDIX

MII MAC Interface

PHY Management Control
Note 7.1
Because the Port 1 PHY and Port 2 PHY are functionally identical, this section will describe
them as the “Port x PHY”, or simply “PHY”. Wherever a lowercase “x” has been appended
to a port or signal name, it can be replaced with “1” or “2” to indicate the Port 1 or Port 2
PHY respectively. All references to “PHY” in this section can be used interchangeably for
both the Port 1 & 2 PHYs. This nomenclature excludes the Virtual PHY.
A block diagram of the Port x PHYs main components can be seen in Figure 7.1.
AutoNegotiation
10/100
Transmitter
MII
To Port x
Switch Fabric MAC
TXPx/TXNx
MII
MAC
Interface
HP Auto-MDIX
To External
Port x Ethernet Pins
RXPx/RXNx
10/100
Reciever
To Host MAC
MDIO
PHY Management
Control
Interrupts
LEDs
To System
Interrupt Controller
To GPIO/LED
Controller
Registers
PLL
From
System Clocks Controller
Figure 7.1 Port x PHY Block Diagram
SMSC LAN9312
83
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
7.2.1
100BASE-TX Transmit
The 100BASE-TX transmit data path is shown in Figure 7.2. Shaded blocks are those which are
internal to the PHY. Each major block is explained in the following sections.
Internal
MII Transmit Clock
100M
PLL
Internal
MII 25 MHz by 4 bits
MII MAC
Interface
Port x
MAC
25MHz
by 4 bits
4B/5B
Encoder
25MHz by
5 bits
Scrambler
and PISO
125 Mbps Serial
NRZI
Converter
MLT-3
Converter
NRZI
100M
TX Driver
MLT-3
MLT-3
Magnetics
MLT-3
RJ45
MLT-3
CAT-5
Figure 7.2 100BASE-TX Transmit Data Path
7.2.1.1
MII MAC Interface
For a transmission, the switch fabric MAC drives the transmit data to the PHYs MII MAC Interface.
The MII MAC Interface is described in detail in Section 7.2.7, "MII MAC Interface".
Note: The PHY is connected to the switch fabric MAC via standard MII signals. Refer to the IEEE
802.3 specification for additional details.
7.2.1.2
4B/5B Encoder
The transmit data passes from the MII block to the 4B/5B Encoder. This block encodes the data from
4-bit nibbles to 5-bit symbols (known as “code-groups”) according to Table 7.2. Each 4-bit data-nibble
is mapped to 16 of the 32 possible code-groups. The remaining 16 code-groups are either used for
control information or are not valid.
The first 16 code-groups are referred to by the hexadecimal values of their corresponding data nibbles,
0 through F. The remaining code-groups are given letter designations with slashes on either side. For
example, an IDLE code-group is /I/, a transmit error code-group is /H/, etc.
Revision 2.0 (02-14-13)
84
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 7.2 4B/5B Code Table
CODE
GROUP
SYM
RECEIVER
INTERPRETATION
11110
0
0
0000
01001
1
1
10100
2
10101
TRANSMITTER
INTERPRETATION
0
0000
0001
1
0001
2
0010
2
0010
3
3
0011
3
0011
01010
4
4
0100
4
0100
01011
5
5
0101
5
0101
01110
6
6
0110
6
0110
01111
7
7
0111
7
0111
10010
8
8
1000
8
1000
10011
9
9
1001
9
1001
10110
A
A
1010
A
1010
10111
B
B
1011
B
1011
11010
C
C
1100
C
1100
11011
D
D
1101
D
1101
11100
E
E
1110
E
1110
11101
F
F
1111
F
1111
11111
/I/
IDLE
Sent after /T/R/ until the MII Transmitter
Enable signal (TXEN) is received
11000
/J/
First nibble of SSD, translated to “0101”
following IDLE, else MII Receive Error
(RXER)
Sent for rising MII Transmitter Enable
signal (TXEN)
10001
/K/
Second nibble of SSD, translated to
“0101” following J, else MII Receive
Error (RXER)
Sent for rising MII Transmitter Enable
signal (TXEN)
01101
/T/
First nibble of ESD, causes de-assertion
of CRS if followed by /R/, else assertion
of MII Receive Error (RXER)
Sent for falling MII Transmitter Enable
signal (TXEN)
00111
/R/
Second nibble of ESD, causes deassertion of CRS if following /T/, else
assertion of MII Receive Error (RXER)
Sent for falling MII Transmitter Enable
signal (TXEN)
00100
/H/
Transmit Error Symbol
Sent for rising MII Transmit Error (TXER)
00110
/V/
INVALID, MII Receive Error (RXER) if
during MII Receive Data Valid (RXDV)
INVALID
11001
/V/
INVALID, MII Receive Error (RXER) if
during MII Receive Data Valid (RXDV)
INVALID
00000
/V/
INVALID, MII Receive Error (RXER) if
during MII Receive Data Valid (RXDV)
INVALID
SMSC LAN9312
DATA
85
DATASHEET
DATA
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 7.2 4B/5B Code Table (continued)
CODE
GROUP
SYM
00001
/V/
INVALID, MII Receive Error (RXER) if
during MII Receive Data Valid (RXDV)
INVALID
00010
/V/
INVALID, MII Receive Error (RXER) if
during MII Receive Data Valid (RXDV)
INVALID
00011
/V/
INVALID, MII Receive Error (RXER) if
during MII Receive Data Valid (RXDV)
INVALID
00101
/V/
INVALID, MII Receive Error (RXER) if
during MII Receive Data Valid (RXDV)
INVALID
01000
/V/
INVALID, MII Receive Error (RXER) if
during MII Receive Data Valid (RXDV)
INVALID
01100
/V/
INVALID, MII Receive Error (RXER) if
during MII Receive Data Valid (RXDV)
INVALID
10000
/V/
INVALID, MII Receive Error (RXER) if
during MII Receive Data Valid (RXDV)
INVALID
7.2.1.3
RECEIVER
INTERPRETATION
TRANSMITTER
INTERPRETATION
Scrambler and PISO
Repeated data patterns (especially the IDLE code-group) can have power spectral densities with large
narrow-band peaks. Scrambling the data helps eliminate these peaks and spread the signal power
more uniformly over the entire channel bandwidth. This uniform spectral density is required by FCC
regulations to prevent excessive EMI from being radiated by the physical wiring. The scrambler also
performs the Parallel In Serial Out conversion (PISO) of the data.
The seed for the scrambler is generated from the PHY address, ensuring that each PHY will have its
own scrambler sequence. For more information on PHY addressing, refer to Section 7.1.1, "PHY
Addressing".
7.2.1.4
NRZI and MLT-3 Encoding
The scrambler block passes the 5-bit wide parallel data to the NRZI converter where it becomes a
serial 125MHz NRZI data stream. The NRZI is then encoded to MLT-3. MLT-3 is a tri-level code where
a change in the logic level represents a code bit “1” and the logic output remaining at the same level
represents a code bit “0”.
7.2.1.5
100M Transmit Driver
The MLT-3 data is then passed to the analog transmitter, which drives the differential MLT-3 signal on
output pins TXPx and TXNx (where “x” is replaced with “1” for the Port 1 PHY, or “2” for the Port 2
PHY), to the twisted pair media across a 1:1 ratio isolation transformer. The 10BASE-T and 100BASETX signals pass through the same transformer so that common “magnetics” can be used for both. The
transmitter drives into the 100Ω impedance of the CAT-5 cable. Cable termination and impedance
matching require external components.
7.2.1.6
100M Phase Lock Loop (PLL)
The 100M PLL locks onto the reference clock and generates the 125MHz clock used to drive the 125
MHz logic and the 100BASE-TX Transmitter.
Revision 2.0 (02-14-13)
86
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
7.2.2
100BASE-TX Receive
The 100BASE-TX receive data path is shown in Figure 7.3. Shaded blocks are those which are internal
to the PHY. Each major block is explained in the following sections.
Internal
MII Receive Clock
100M
PLL
Port x
MAC
Internal
MII 25MHz by 4 bits
MII MAC
Interface
25MHz
by 4 bits
4B/5B
Decoder
25MHz by
5 bits
Descrambler
and SIPO
125 Mbps Serial
NRZI
Converter
A/D
Converter
NRZI
MLT-3
MLT-3
Converter
Magnetics
MLT-3
MLT-3
RJ45
DSP: Timing
recovery, Equalizer
and BLW Correction
MLT-3
CAT-5
6 bit Data
Figure 7.3 100BASE-TX Receive Data Path
7.2.2.1
A/D Converter
The MLT-3 data from the cable is fed into the PHY on inputs RXPx and RXNx (where “x” is replaced
with “1” for the Port 1 PHY, or “2” for the Port 2 PHY) via a 1:1 ratio transformer. The ADC samples
the incoming differential signal at a rate of 125M samples per second. Using a 64-level quantizer, 6
digital bits are generated to represent each sample. The DSP adjusts the gain of the A/D Converter
(ADC) according to the observed signal levels such that the full dynamic range of the ADC can be
used.
7.2.2.2
DSP: Equalizer, BLW Correction and Clock/Data Recovery
The 6 bits from the ADC are fed into the DSP block. The equalizer in the DSP section compensates
for phase and amplitude distortion caused by the physical channel (magnetics, connectors, and CAT5 cable). The equalizer can restore the signal for any good-quality CAT-5 cable between 1m and 150m.
If the DC content of the signal is such that the low-frequency components fall below the low frequency
pole of the isolation transformer, then the droop characteristics of the transformer will become
significant and Baseline Wander (BLW) on the received signal will result. To prevent corruption of the
received data, the PHY corrects for BLW and can receive the ANSI X3.263-1995 FDDI TP-PMD
defined “killer packet” with no bit errors.
The 100M PLL generates multiple phases of the 125MHz clock. A multiplexer, controlled by the timing
unit of the DSP, selects the optimum phase for sampling the data. This is used as the received
recovered clock. This clock is used to extract the serial data from the received signal.
SMSC LAN9312
87
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
7.2.2.3
NRZI and MLT-3 Decoding
The DSP generates the MLT-3 recovered levels that are fed to the MLT-3 converter. The MLT-3 is then
converted to an NRZI data stream.
7.2.2.4
Descrambler and SIPO
The descrambler performs an inverse function to the scrambler in the transmitter and also performs
the Serial In Parallel Out (SIPO) conversion of the data.
During reception of IDLE (/I/) symbols. the descrambler synchronizes its descrambler key to the
incoming stream. Once synchronization is achieved, the descrambler locks on this key and is able to
descramble incoming data.
Special logic in the descrambler ensures synchronization with the remote PHY by searching for IDLE
symbols within a window of 4000 bytes (40us). This window ensures that a maximum packet size of
1514 bytes, allowed by the IEEE 802.3 standard, can be received with no interference. If no IDLEsymbols are detected within this time-period, receive operation is aborted and the descrambler re-starts
the synchronization process.
The de-scrambled signal is then aligned into 5-bit code-groups by recognizing the /J/K/ Start-of-Stream
Delimiter (SSD) pair at the start of a packet. Once the code-word alignment is determined, it is stored
and utilized until the next start of frame.
7.2.2.5
5B/4B Decoding
The 5-bit code-groups are translated into 4-bit data nibbles according to the 4B/5B table shown in
Table 7.2. The translated data is presented on the internal MII RXD[3:0] signal lines to the switch fabric
MAC. The SSD, /J/K/, is translated to “0101 0101” as the first 2 nibbles of the MAC preamble.
Reception of the SSD causes the PHY to assert the RXDV signal, indicating that valid data is available
on the RXD bus. Successive valid code-groups are translated to data nibbles. Reception of either the
End of Stream Delimiter (ESD) consisting of the /T/R/ symbols, or at least two /I/ symbols causes the
PHY to de-assert carrier sense and RXDV. These symbols are not translated into data.
7.2.2.6
Receiver Errors
During a frame, unexpected code-groups are considered receive errors. Expected code groups are the
DATA set (0 through F), and the /T/R/ (ESD) symbol pair. When a receive error occurs, the internal
MII’s RXER signal is asserted and arbitrary data is driven onto the internal receive data bus (RXD) to
the switch fabric MAC. Should an error be detected during the time that the /J/K/ delimiter is being
decoded (bad SSD error), RXER is asserted and the value 1110b is driven onto the internal receive
data bus (RXD) to the switch fabric MAC. Note that the internal MII’s data valid signal (RXDV) is not
yet asserted when the bad SSD occurs.
7.2.2.7
MII MAC Interface
For reception, the 4-bit data nibbles are sent to the MII MAC Interface block where they are sent via
MII to the switch fabric MAC. The MII MAC Interface is described in detail in Section 7.2.7, "MII MAC
Interface".
Note: The PHY is connected to the switch fabric MAC via standard MII signals. Refer to the IEEE
802.3 specification for additional details.
Revision 2.0 (02-14-13)
88
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
7.2.3
10BASE-T Transmit
Data to be transmitted comes from the switch fabric MAC. The 10BASE-T transmitter receives 4-bit
nibbles from the internal MII at a rate of 2.5MHz and converts them to a 10Mbps serial data stream.
The data stream is then Manchester-encoded and sent to the analog transmitter, which drives a signal
onto the twisted pair via the external magnetics.
10BASE-T transmissions use the following blocks:
7.2.3.1

MII MAC Interface (digital)

10M TX Driver (digital/analog)

10M PLL (analog)
MII MAC Interface
For a transmission, the switch fabric MAC drives the transmit data to the PHYs MII MAC Interface.
The MII MAC Interface is described in detail in Section 7.2.7, "MII MAC Interface".
Note: The PHY is connected to the switch fabric MAC via standard MII signals. Refer to the IEEE
802.3 specification for additional details.
7.2.3.2
10M TX Driver and PLL
The 4-bit wide data is sent to the 10M TX Driver block. The nibbles are converted to a 10Mbps serial
NRZI data stream. The 10M PLL locks onto the external clock or internal oscillator and produces a
20MHz clock. This is used to Manchester encode the NRZ data stream. When no data is being
transmitted (TXEN is low), the 10M TX Driver block outputs Normal Link Pulses (NLPs) to maintain
communications with the remote link partner. The manchester encoded data is sent to the analog
transmitter where it is shaped and filtered before being driven out as a differential signal across the
TXPx and TXNx outputs (where “x” is replaced with “1” for the Port 1 PHY, or “2” for the Port 2 PHY).
7.2.4
10BASE-T Receive
The 10BASE-T receiver gets the Manchester-encoded analog signal from the cable via the magnetics.
It recovers the receive clock from the signal and uses this clock to recover the NRZI data stream. This
10M serial data is converted to 4-bit data nibbles which are passed to the controller across the internal
MII at a rate of 2.5MHz.
10BASE-T reception uses the following blocks:
7.2.4.1

Filter and SQUELCH (analog)

10M RX (digital/analog)

MII MAC Interface (digital)

10M PLL (analog)
Filter and Squelch
The Manchester signal from the cable is fed into the PHY on inputs RXPx and RXNx (where “x” is
replaced with “1” for Port 1, or “2” for Port 2) via 1:1 ratio magnetics. It is first filtered to reduce any
out-of-band noise. It then passes through a SQUELCH circuit. The SQUELCH is a set of amplitude
and timing comparators that normally reject differential voltage levels below 300mV and detect and
recognize differential voltages above 585mV.
7.2.4.2
10M RX and PLL
The output of the SQUELCH goes to the 10M RX block where it is validated as Manchester encoded
data. The polarity of the signal is also checked. If the polarity is reversed (local RXP is connected to
RXN of the remote partner and vice versa), then this is identified and corrected. The reversed condition
SMSC LAN9312
89
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
is indicated by the flag “XPOL“, bit 4 in Port x PHY Special Control/Status Indication Register
(PHY_SPECIAL_CONTROL_STAT_IND_x). The 10M PLL locks onto the received Manchester signal
and generates the received 20MHz clock from it. Using this clock, the Manchester encoded data is
extracted and converted to a 10MHz NRZI data stream. It is then converted from serial to 4-bit wide
parallel data.
The RX10M block also detects valid 10BASE-T IDLE signals - Normal Link Pulses (NLPs) - to maintain
the link.
7.2.4.3
MII MAC Interface
For reception, the 4-bit data nibbles are sent to the MII MAC Interface block where they are sent via
MII to the switch fabric MAC. The MII MAC Interface is described in detail in Section 7.2.7, "MII MAC
Interface".
Note: The PHY is connected to the switch fabric MAC via standard MII signals. Refer to the IEEE
802.3 specification for additional details.
7.2.4.4
Jabber Detection
Jabber is a condition in which a station transmits for a period of time longer than the maximum
permissible packet length, usually due to a fault condition, that results in holding the TXEN input for
an extended period of time. Special logic is used to detect the jabber state and abort the transmission
to the line, within 45ms. Once TXEN is deasserted, the logic resets the jabber condition.
7.2.5
PHY Auto-negotiation
The purpose of the auto-negotiation function is to automatically configure the PHY to the optimum link
parameters based on the capabilities of its link partner. Auto-negotiation is a mechanism for
exchanging configuration information between two link-partners and automatically selecting the highest
performance mode of operation supported by both sides. Auto-negotiation is fully defined in clause 28
of the IEEE 802.3 specification and is enabled by setting bit 12 (PHY_AN) of the Port x PHY Basic
Control Register (PHY_BASIC_CONTROL_x).
The advertised capabilities of the PHY are stored in the Port x PHY Auto-Negotiation Advertisement
Register (PHY_AN_ADV_x). The PHY contains the ability to advertise 100BASE-TX and 10BASE-T in
both full or half-duplex modes. Besides the connection speed, the PHY can advertise remote fault
indication and symmetric or asymmetric pause flow control as defined in the IEEE 802.3 specification.
The LAN9312 does not support “Next Page” capability. Many of the default advertised capabilities of
the PHY are determined via configuration straps as shown in Section 14.4.2.5, "Port x PHY AutoNegotiation Advertisement Register (PHY_AN_ADV_x)," on page 294. Refer to Section 4.2.4,
"Configuration Straps," on page 40 for additional details on how to use the LAN9312 configuration
straps.
Once auto-negotiation has completed, information about the resolved link and the results of the
negotiation process are reflected in the speed indication bits in the Port x PHY Special Control/Status
Register (PHY_SPECIAL_CONTROL_STATUS_x), as well as the Port x PHY Auto-Negotiation Link
Partner Base Page Ability Register (PHY_AN_LP_BASE_ABILITY_x).
The auto-negotiation protocol is a purely physical layer activity and proceeds independently of the MAC
controller.
The following blocks are activated during an Auto-negotiation session:

Auto-negotiation (digital)

100M ADC (analog)

100M PLL (analog)

100M equalizer/BLW/clock recovery (DSP)

10M SQUELCH (analog)
Revision 2.0 (02-14-13)
90
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet

10M PLL (analog)

10M TX Driver (analog)
Auto-negotiation is started by the occurrence of any of the following events:

Power-On Reset (POR)

Hardware reset (nRST)

PHY Software reset (via Reset Control Register (RESET_CTL), or bit 15 of the Port x PHY Basic
Control Register (PHY_BASIC_CONTROL_x))

PHY Power-down reset (Section 7.2.9, "PHY Power-Down Modes," on page 94)

PHY Link status down (bit 2 of the Port x PHY Basic Status Register (PHY_BASIC_STATUS_x) is
cleared)

Setting the Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x), bit 9 high (auto-neg
restart)

Digital Reset (via bit 0 of the Reset Control Register (RESET_CTL))

Issuing an EEPROM Loader RELOAD command (Section 10.2.4, "EEPROM Loader," on page 149)
Note: Refer to Section 4.2, "Resets," on page 36 for information on these and other system resets.
On detection of one of these events, the PHY begins auto-negotiation by transmitting bursts of Fast
Link Pulses (FLP). These are bursts of link pulses from the 10M TX Driver. They are shaped as Normal
Link Pulses and can pass uncorrupted down CAT-3 or CAT-5 cable. A Fast Link Pulse Burst consists
of up to 33 pulses. The 17 odd-numbered pulses, which are always present, frame the FLP burst. The
16 even-numbered pulses, which may be present or absent, contain the data word being transmitted.
Presence of a data pulse represents a “1”, while absence represents a “0”.
The data transmitted by an FLP burst is known as a “Link Code Word.” These are defined fully in IEEE
802.3 clause 28. In summary, the PHY advertises 802.3 compliance in its selector field (the first 5 bits
of the Link Code Word). It advertises its technology ability according to the bits set in the Port x PHY
Auto-Negotiation Advertisement Register (PHY_AN_ADV_x).
There are 4 possible matches of the technology abilities. In the order of priority these are:

100M Full Duplex (highest priority)

100M Half Duplex

10M Full Duplex

10M Half Duplex (lowest priority)
If the full capabilities of the PHY are advertised (100M, full-duplex), and if the link partner is capable
of 10M and 100M, then auto-negotiation selects 100M as the highest performance mode. If the link
partner is capable of half and full-duplex modes, then auto-negotiation selects full-duplex as the highest
performance mode.
Once a speed and duplex match has been determined, the link code words are repeated with the
acknowledge bit set. Any difference in the main content of the link code words at this time will cause
auto-negotiation to re-start. Auto-negotiation will also re-start if all of the required FLP bursts are not
received.
Writing the Port x PHY Auto-Negotiation Advertisement Register (PHY_AN_ADV_x) bits [8:5] allows
software control of the capabilities advertised by the PHY. Writing the Port x PHY Auto-Negotiation
Advertisement Register (PHY_AN_ADV_x) does not automatically re-start auto-negotiation. The Port
x PHY Basic Control Register (PHY_BASIC_CONTROL_x), bit 9 must be set before the new abilities
will be advertised. Auto-negotiation can also be disabled via software by clearing bit 12 of the Port x
PHY Basic Control Register (PHY_BASIC_CONTROL_x).
SMSC LAN9312
91
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
7.2.5.1
PHY Pause Flow Control
The Port 1 & 2 PHYs are capable of generating and receiving pause flow control frames per the IEEE
802.3 specification. The PHYs advertised pause flow control abilities are set via bits 10 (Symmetric
Pause) and 11 (Asymmetric Pause) of the Port x PHY Auto-Negotiation Advertisement Register
(PHY_AN_ADV_x). This allows the PHY to advertise its flow control abilities and auto-negotiate the
flow control settings with its link partner. The default values of these bits are determined via
configuration straps as defined in Section 14.4.2.5, "Port x PHY Auto-Negotiation Advertisement
Register (PHY_AN_ADV_x)," on page 294.
The pause flow control settings may also be manually set via the manual flow control registers Port 1
Manual Flow Control Register (MANUAL_FC_1) and Port 2 Manual Flow Control Register
(MANUAL_FC_2). These registers allow the switch fabric ports flow control settings to be manually set
when auto-negotiation is disabled or the Manual Flow Control Select bit 0 is set. The currently enabled
duplex and flow control settings can also be monitored via these registers. The flow control values in
the Port x PHY Auto-Negotiation Advertisement Register (PHY_AN_ADV_x) are not affected by the
values of the manual flow control register. Refer to Section 6.2.3, "Flow Control Enable Logic," on
page 58 for additional information.
7.2.5.2
Parallel Detection
If the LAN9312 is connected to a device lacking the ability to auto-negotiate (i.e. no FLPs are
detected), it is able to determine the speed of the link based on either 100M MLT-3 symbols or 10M
Normal Link Pulses. In this case the link is presumed to be half-duplex per the IEEE 802.3 standard.
This ability is known as “Parallel Detection.” This feature ensures interoperability with legacy link
partners. If a link is formed via parallel detection, then bit 0 in the Port x PHY Auto-Negotiation
Expansion Register (PHY_AN_EXP_x) is cleared to indicate that the link partner is not capable of autonegotiation. If a fault occurs during parallel detection, bit 4 of the Port x PHY Auto-Negotiation
Expansion Register (PHY_AN_EXP_x) is set.
The Port x PHY Auto-Negotiation Link Partner Base Page Ability Register
(PHY_AN_LP_BASE_ABILITY_x) is used to store the Link Partner Ability information, which is coded
in the received FLPs. If the link partner is not auto-negotiation capable, then this register is updated
after completion of parallel detection to reflect the speed capability of the link partner.
7.2.5.3
Restarting Auto-Negotiation
Auto-negotiation can be re-started at any time by setting bit 9 of the Port x PHY Basic Control Register
(PHY_BASIC_CONTROL_x). Auto-negotiation will also re-start if the link is broken at any time. A
broken link is caused by signal loss. This may occur because of a cable break, or because of an
interruption in the signal transmitted by the Link Partner. Auto-negotiation resumes in an attempt to
determine the new link configuration.
If the management entity re-starts Auto-negotiation by writing to bit 9 of the Port x PHY Basic Control
Register (PHY_BASIC_CONTROL_x), the LAN9312 will respond by stopping all transmission/receiving
operations. Once the internal break link time of approximately 1200ms has passed in the Autonegotiation state-machine, the auto-negotiation will re-start. In this case, the link partner will have also
dropped the link due to lack of a received signal, so it too will resume auto-negotiation.
7.2.5.4
Disabling Auto-Negotiation
Auto-negotiation can be disabled by clearing bit 12 of the Port x PHY Basic Control Register
(PHY_BASIC_CONTROL_x). The PHY will then force its speed of operation to reflect the speed (bit
13) and duplex (bit 8) of the Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x). The
speed and duplex bits in the Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x) should
be ignored when auto-negotiation is enabled.
Revision 2.0 (02-14-13)
92
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
7.2.5.5
Half Vs. Full-Duplex
Half-duplex operation relies on the CSMA/CD (Carrier Sense Multiple Access / Collision Detect)
protocol to handle network traffic and collisions. In this mode, the carrier sense signal, CRS, responds
to both transmit and receive activity. If data is received while the PHY is transmitting, a collision results.
In full-duplex mode, the PHY is able to transmit and receive data simultaneously. In this mode, CRS
responds only to receive activity. The CSMA/CD protocol does not apply and collision detection is
disabled.
7.2.6
HP Auto-MDIX
HP Auto-MDIX facilitates the use of CAT-3 (10 BASE-T) or CAT-5 (100 BASE-T) media UTP
interconnect cable without consideration of interface wiring scheme. If a user plugs in either a direct
connect LAN cable or a cross-over patch cable, as shown in Figure 7.4 (See Note 7.1 on page 83), the
PHY is capable of configuring the TXPx/TXNx and RXPx/RXNx twisted pair pins for correct transceiver
operation.
The internal logic of the device detects the TX and RX pins of the connecting device. Since the RX
and TX line pairs are interchangeable, special PCB design considerations are needed to accommodate
the symmetrical magnetics and termination of an Auto-MDIX design.
The Auto-MDIX function can be disabled through bit 15 (AMDIXCTRL) of the Port x PHY Special
Control/Status Indication Register (PHY_SPECIAL_CONTROL_STAT_IND_x). When AMDIXCTRL is
cleared, Auto-MDIX can be selected via the auto_mdix_strap_x configuration strap. The MDIX can also
be configured manually via the manual_mdix_strap_x if both the AMDIXCTRL bit and the
auto_mdix_strap_x configuration strap are low. Refer to Section 3.2, "Pin Descriptions," on page 28 for
more information on the configuration straps.
When bit 15 (AMDIXCTRL) of the Port x PHY Special Control/Status Indication Register
(PHY_SPECIAL_CONTROL_STAT_IND_x) is set to 1, the Auto-MDIX capability is determined by bits
1 3 a n d 1 4 o f t h e P o r t x P H Y Sp e c i a l C o n t r o l / St a t u s I n d i c a t i o n R e g i s t e r
(PHY_SPECIAL_CONTROL_STAT_IND_x).
RJ-45 8-pin straight-through
for 10BASE-T/100BASE-TX
signaling
RJ-45 8-pin cross-over for
10BASE-T/100BASE-TX
signaling
TXPx
1
1
TXPx
TXPx
1
1
TXPx
TXNx
2
2
TXNx
TXNx
2
2
TXNx
RXPx
3
3
RXPx
RXPx
3
3
RXPx
Not Used
4
4
Not Used
Not Used
4
4
Not Used
Not Used
5
5
Not Used
Not Used
5
5
Not Used
RXNx
6
6
RXNx
RXNx
6
6
RXNx
Not Used
7
7
Not Used
Not Used
7
7
Not Used
Not Used
8
8
Not Used
Not Used
8
8
Not Used
Direct Connect Cable
Cross-Over Cable
Figure 7.4 Direct Cable Connection vs. Cross-Over Cable Connection
7.2.7
MII MAC Interface
The MII MAC Interface is responsible for the transmission and reception of the Ethernet data to and
from the switch fabric MAC. The PHY is connected internally to the switch fabric MAC via standard
MII signals per IEEE 802.3.
SMSC LAN9312
93
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
For a transmission, the switch fabric MAC drives the transmit data onto the internal MII TXD bus and
asserts TXEN to indicate valid data. The data is in the form of 4-bit wide data at a rate of 25MHz for
100BASE-TX, or 2.5MHz for 10BASE-T.
For reception, the 4-bit data nibbles are sent to the MII MAC Interface block. These data nibbles are
clocked to the controller at a rate of 25MHz for 100BASE-TX, or 2.5MHz for 10BASE-T. RXCLK is the
output clock for the internal MII bus. It is recovered from the received data to clock the RXD bus. If
there is no received signal, it is derived from the system reference clock.
7.2.8
PHY Management Control
The PHY Management Control block is responsible for the management functions of the PHY,
including register access and interrupt generation. A Serial Management Interface (SMI) is used to
support registers 0 through 6 as required by the IEEE 802.3 (Clause 22), as well as the vendor specific
registers allowed by the specification. The SMI interface consists of the MII Management Data (MDIO)
signal and the MII Management Clock (MDC) signal. These signals interface to the Host MAC and
allow access to all PHY registers. Refer to Section 14.4.2, "Port 1 & 2 PHY Registers," on page 286
for a list of all supported registers and register descriptions. Non-supported registers will be read as
FFFFh.
7.2.8.1
PHY Interrupts
The PHY contains the ability to generate various interrupt events as described in Table 7.3. Reading
the Port x PHY Interrupt Source Flags Register (PHY_INTERRUPT_SOURCE_x) shows the source of
the interrupt, and clears the interrupt signal. The Port x PHY Interrupt Mask Register
(PHY_INTERRUPT_MASK_x) enables or disables each PHY interrupt. The PHY Management Control
block aggregates the enabled interrupts status into an internal signal which is sent to the System
Interrupt Controller and is reflected via the Interrupt Status Register (INT_STS) bit 26 (PHY_INT1) for
the Port 1 PHY, and bit 27 (PHY_INT2) for the Port 2 PHY. For more information on the LAN9312
interrupts, refer to Chapter 5, "System Interrupts," on page 49.
Table 7.3 PHY Interrupt Sources
7.2.9
INTERRUPT SOURCE
PHY_INTERRUPT_MASK_x &
PHY_INTERRUPT_SOURCE_x REGISTER BIT #
ENERGYON Activated
7
Auto-Negotiation Complete
6
Remote Fault Detected
5
Link Down (Link Status Negated)
4
Auto-Negotiation LP Acknowledge
3
Parallel Detection Fault
2
Auto-Negotiation Page Received
1
PHY Power-Down Modes
There are two power-down modes for the PHY:

PHY General Power-Down

PHY Energy Detect Power-Down
Note: For more information on the various power management features of the LAN9312, refer to
Section 4.3, "Power Management," on page 46.
Revision 2.0 (02-14-13)
94
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Note: The power-down modes of each PHY (Port 1 PHY and Port 2 PHY) are controlled
independently.
Note: The PHY power-down modes do not reload or reset the PHY registers.
7.2.9.1
PHY General Power-Down
This power-down mode is controlled by bit 11 of the Port x PHY Basic Control Register
(PHY_BASIC_CONTROL_x). In this mode the entire PHY, except the PHY management control
interface, is powered down. The PHY will remain in this power-down state as long as bit 11 is set.
When bit 11 is cleared, the PHY powers up and is automatically reset.
7.2.9.2
PHY Energy Detect Power-Down
This power-down mode is enabled by setting bit 13 (EDPWRDOWN) of the Port x PHY Mode
Control/Status Register (PHY_MODE_CONTROL_STATUS_x). When in this mode, if no energy is
detected on the line, the entire PHY is powered down except for the PHY management control
interface, the SQUELCH circuit, and the ENERGYON logic. The ENERGYON logic is used to detect
the presence of valid energy from 100BASE-TX, 10BASE-T, or auto-negotiation signals and is
responsible for driving the ENERGYON signal (bit 1) of the Port x PHY Mode Control/Status Register
(PHY_MODE_CONTROL_STATUS_x).
In this mode, when the ENERGYON signal is cleared, the PHY is powered down and no data is
transmitted from the PHY. When energy is received, via link pulses or packets, the ENERGYON signal
goes high, and the PHY powers up. The PHY automatically resets itself into its previous state prior to
power-down, and asserts the INT7 interrupt (bit 7) of the Port x PHY Interrupt Source Flags Register
(PHY_INTERRUPT_SOURCE_x). The first and possibly second packet to activate ENERGYON may
be lost.
W h e n b i t 1 3 ( E D P W R D O W N ) o f t h e P o r t x P H Y M o d e C o n t r o l / St a t u s R e g i s t e r
(PHY_MODE_CONTROL_STATUS_x) is low, energy detect power-down is disabled.
The energy detect power down feature is part of the broader power management features of the
LAN9312 and can be used to trigger the power management event output pin (PME). This is
accomplished by enabling the energy detect power-down feature of the PHY as described above, and
setting the corresponding energy detect enable (bit 14 for Port 1 PHY, bit 15 for Port 2 PHY) of the
Power Management Control Register (PMT_CTRL). Refer to Section 4.3, "Power Management," on
page 46 for additional information.
7.2.10
PHY Resets
In addition to the chip-level hardware reset (nRST) and Power-On Reset (POR), the PHY supports
three block specific resets. These are discussed in the following sections. For detailed information on
all LAN9312 resets and the reset sequence refer to Section 4.2, "Resets," on page 36.
Note: The DIGITAL_RST bit in the Reset Control Register (RESET_CTL) does not reset the PHYs.
Only a hardware reset (nRST) or an EEPROM RELOAD command will automatically reload
the configuration strap values into the PHY registers. For all other PHY resets, these values
will need to be manually configured via software.
7.2.10.1
PHY Software Reset via RESET_CTL
The PHY can be reset via the Reset Control Register (RESET_CTL). The Port 1 PHY is reset by
setting bit 1 (PHY1_RST), and the Port 2 PHY is reset by setting bit 2 (PHY2_RST). These bits are
self clearing after approximately 102uS. This reset does not reload the configuration strap values into
the PHY registers.
SMSC LAN9312
95
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
7.2.10.2
PHY Software Reset via PHY_BASIC_CTRL_x
The PHY can also be reset by setting bit 15 (PHY_RST) of the Port x PHY Basic Control Register
(PHY_BASIC_CONTROL_x). This bit is self clearing and will return to 0 after the reset is complete.
This reset does not reload the configuration strap values into the PHY registers.
7.2.10.3
PHY Power-Down Reset
After the PHY has returned from a power-down state, a reset of the PHY is automatically generated.
The PHY power-down modes do not reload or reset the PHY registers. Refer to Section 7.2.9, "PHY
Power-Down Modes," on page 94 for additional information.
7.2.11
LEDs
Each PHY provides LED indication signals to the GPIO/LED block of the LAN9312. This allows
external LEDs to be used to indicate various PHY related functions such as TX/RX activity, speed,
duplex, or link status. Refer to Chapter 13, "GPIO/LED Controller," on page 162 for additional
information on the configuration of these signals.
7.2.12
Required Ethernet Magnetics
The magnetics selected for use with the LAN9312 should be an Auto-MDIX style magnetic, which is
widely available from several vendors. Please review the SMSC Application note 8.13 “Suggested
Magnetics” for the latest qualified and suggested magnetics. A list of vendors and part numbers are
provided within the application note.
7.3
Virtual PHY
The Virtual PHY provides a basic MII management interface (MDIO) to the Host MAC per the IEEE
802.3 (clause 22) so that an unmodified driver can be supported as if the Host MAC was attached to
a single port PHY. This functionality is designed to allow easy and quick integration of the LAN9312
into designs with minimal driver modifications. The Virtual PHY provides a full bank of registers which
comply with the IEEE 802.3 specification. This enables the Virtual PHY to provide various status and
control bits similar to those provided by a real PHY. These include the output of speed selection,
duplex, loopback, isolate, collision test, and auto-negotiation status. For a list of all Virtual PHY
registers and related bit descriptions, refer to Section 14.4.1, "Virtual PHY Registers," on page 286.
7.3.1
Virtual PHY Auto-Negotiation
The purpose of the auto-negotiation function is to automatically configure the Virtual PHY to the
optimum link parameters based on the capabilities of its link partner. Because the Virtual PHY has no
actual link partner, the auto-negotiation process is emulated with deterministic results.
Auto-negotiation is enabled by setting bit 12 (VPHY_AN) of the Virtual PHY Basic Control Register
(VPHY_BASIC_CTRL) and is restarted by the occurrence of any of the following events:

Power-On Reset (POR)

Hardware reset (nRST)

PHY Software reset (via bit 3 of the Reset Control Register (RESET_CTL), bit 0 of the Power
Management Control Register (PMT_CTRL), or bit 15 of the Virtual PHY Basic Control Register
(VPHY_BASIC_CTRL))

Setting the Virtual PHY Basic Control Register (VPHY_BASIC_CTRL), bit 9 high (auto-neg restart)

Digital Reset (via bit 10 of the Reset Control Register (RESET_CTL))

Issuing an EEPROM Loader RELOAD command (Section 10.2.4, "EEPROM Loader," on page 149)
The emulated auto-negotiation process is much simpler than the real process and can be categorized
into three steps:
Revision 2.0 (02-14-13)
96
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
1. Bit 5 (Auto-Negotiation Complete) is set in the Virtual PHY Basic Status Register
(VPHY_BASIC_STATUS).
2. Bit 1 (Page Received) is set in the Virtual PHY Auto-Negotiation Expansion Register
(VPHY_AN_EXP).
3. The auto-negotiation result (speed and duplex) is determined and registered.
The auto-negotiation result (speed and duplex) is determined using the Highest Common Denominator
(HCD) of the Virtual PHY Auto-Negotiation Advertisement Register (VPHY_AN_ADV) and Virtual PHY
Auto-Negotiation Link Partner Base Page Ability Register (VPHY_AN_LP_BASE_ABILITY) as
specified in the IEEE 802.3 standard. The technology ability bits of these registers are ANDed, and if
there are multiple bits in common, the priority is determined as follows:

100Mbps Full Duplex (highest priority)

100Mbps Half Duplex

10Mbps Full Duplex

10Mbps Half Duplex (lowest priority)
For example, if the full capabilities of the Virtual PHY are advertised (100Mbps, Full Duplex), and if
the link partner is capable of 10Mbps and 100Mbps, then auto-negotiation selects 100Mbps as the
highest performance mode. If the link partner is capable of half and full-duplex modes, then autonegotiation selects full-duplex as the highest performance operation. In the event that there are no bits
in common, an emulated Parallel Detection is used.
The Virtual PHY Auto-Negotiation Advertisement Register (VPHY_AN_ADV) defaults to having all four
ability bits set. These values can be reconfigured via software. Once the auto-negotiation is complete,
any change to the Virtual PHY Auto-Negotiation Advertisement Register (VPHY_AN_ADV) will not take
affect until the auto-negotiation process is re-run. The emulated link partner always advertises all four
abilities (100BASE-X full duplex, 100BASE-X half duplex, 10BASE-T full duplex, and 10BASE-T half
duplex) in the Virtual PHY Auto-Negotiation Link Partner Base Page Ability Register
(VPHY_AN_LP_BASE_ABILITY). Neither the Virtual PHY or the emulated link partner support next
page capability, remote faults, or 100BASE-T4.
If there is at least one common selection between the emulated link partner and the Virtual PHY
advertised abilities, then the auto-negotiation succeeds, the Link Partner Auto-Negotiation Able bit 0
of the Virtual PHY Auto-Negotiation Expansion Register (VPHY_AN_EXP) is set, and the technology
ability bits in the Virtual PHY Auto-Negotiation Link Partner Base Page Ability Register
(VPHY_AN_LP_BASE_ABILITY) are set to indicate the emulated link partners abilities.
Note: For the Virtual PHY, the auto-negotiation register bits (and management of such) are used by
the Host MAC. So the perception of local and link partner is reversed. The local device is the
Host MAC, while the link partner is the switch fabric. This is consistent with the intention of the
Virtual PHY.
7.3.1.1
Parallel Detection
In the event that there are no common bits between the advertised ability and the emulated link
partners ability, auto-negotiation fails and emulated parallel detect is used. In this case, the Link
Partner Auto-Negotiation Able (bit 0) in the Virtual PHY Auto-Negotiation Expansion Register
(VPHY_AN_EXP) will be cleared, and the communication set to 100Mbps half-duplex. Only one of the
technology ability bits in the Virtual PHY Auto-Negotiation Link Partner Base Page Ability Register
(VPHY_AN_LP_BASE_ABILITY) will be set, indicating the emulated parallel detect result.
7.3.1.2
Disabling Auto-Negotiation
Auto-negotiation can be disabled in the Virtual PHY by clearing bit 12 (VPHY_AN) of the Virtual PHY
Basic Control Register (VPHY_BASIC_CTRL). The Virtual PHY will then force its speed of operation
to reflect the speed (bit 13) and duplex (bit 8) of the Virtual PHY Basic Control Register
(VPHY_BASIC_CTRL). The speed and duplex bits in the Virtual PHY Basic Control Register
(VPHY_BASIC_CTRL) should be ignored when auto-negotiation is enabled.
SMSC LAN9312
97
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
7.3.1.3
Virtual PHY Pause Flow Control
The Virtual PHY supports pause flow control per the IEEE 802.3 specification. The Virtual PHYs
advertised pause flow control abilities are set via bits 10 (Symmetric Pause) and 11 (Asymmetric
Pause) of the Virtual PHY Auto-Negotiation Advertisement Register (VPHY_AN_ADV). This allows the
Virtual PHY to advertise its flow control abilities and auto-negotiate the flow control settings with the
emulated link partner. The default values of these bits are as shown in Section 14.2.8.5, "Virtual PHY
Auto-Negotiation Advertisement Register (VPHY_AN_ADV)," on page 252.
The symmetric/asymmetric pause ability of the emulated link partner is based upon the advertised
pause flow control abilities of the Virtual PHY in (bits 10 & 11) of the Virtual PHY Auto-Negotiation
Advertisement Register (VPHY_AN_ADV). Thus, the emulated link partner always accommodates the
asymmetric/symmetric pause ability settings requested by the Virtual PHY, as shown in Table 14.5,
“Emulated Link Partner Pause Flow Control Ability Default Values,” on page 255.
The pause flow control settings may also be manually set via the Port 0(Host MAC) Manual Flow
Control Register (MANUAL_FC_MII). This register allows the switch fabric port 0 flow control settings
to be manually set when auto-negotiation is disabled or the Manual Flow Control Select bit 0 is set.
The currently enabled duplex and flow control settings can also be monitored via this register. The flow
control values in the Virtual PHY Auto-Negotiation Advertisement Register (VPHY_AN_ADV) are not
affected by the values of the manual flow control register. Refer to Section 6.2.3, "Flow Control Enable
Logic," on page 58 for additional information.
7.3.2
Virtual PHY Resets
In addition to the chip-level hardware reset (nRST) and Power-On Reset (POR), the Virtual PHY
supports three block specific resets. These are is discussed in the following sections. For detailed
information on all LAN9312 resets, refer to Section 4.2, "Resets," on page 36.
7.3.2.1
Virtual PHY Software Reset via RESET_CTL
The Virtual PHY can be reset via the Reset Control Register (RESET_CTL) by setting bit 3
(VPHY_RST). This bit is self clearing after approximately 102uS.
7.3.2.2
Virtual PHY Software Reset via VPHY_BASIC_CTRL
The Virtual PHY can also be reset by setting bit 15 (VPHY_RST) of the Virtual PHY Basic Control
Register (VPHY_BASIC_CTRL). This bit is self clearing and will return to 0 after the reset is complete.
7.3.2.3
Virtual PHY Software Reset via PMT_CTRL
The Virtual PHY can be reset via the Power Management Control Register (PMT_CTRL) by setting bit
10 (VPHY_RST). This bit is self clearing after approximately 102uS.
Revision 2.0 (02-14-13)
98
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 8 Host Bus Interface (HBI)
8.1
Functional Overview
The Host Bus Interface (HBI) module provides a high-speed asynchronous SRAM-like slave interface
that facilitates communication between the LAN9312 and a host system. The HBI allows access to the
System CSRs and handles byte swapping based on the dynamic endianess select. The HBI interfaces
to the switch fabric via the Host MAC, which contains the TX/RX Data and Status FIFOs, Host MAC
registers and power management features. Refer to Chapter 9, "Host MAC," on page 112 for detailed
information on the Host MAC.
The following is an overview of the functions provided by the HBI:
Asynchronous 32-bit Host Bus Interface: The HBI provides an asynchronous SRAM-like Host Bus
Interface that is compatible with most CPUs.

Host data bus endianess control: The HBI supports dynamic selection of big and little endian
host byte ordering based on the END_SEL input pin. This highly flexible interface provides mixed
endian access for registers and memory.

Direct FIFO access modes: When the FIFO_SEL input pin is high during host access, all host
write operations are to the TX data FIFO and all host read operations are from the RX data FIFOs.
This feature facilitates operation with host DMA controllers that do not support FIFO operations.
System CSR’s: The HBI allows for configuration and monitoring of the various LAN9312 functions
through the System Control and Status Registers (CSRs). These registers are accessible to the host
via the Host Bus Interface and allow direct (and indirect) access to all the LAN9312 functions. For a
full list of all System CSR’s and their descriptions, refer to Section 14.2, "System Control and Status
Registers".
Interrupt support: The HBI supports a variety of interrupt sources. Individual interrupts can be
monitored and enabled/disabled via registers within the System CSRs for output on the IRQ pin. For
more information on interrupts, refer to Chapter 5, "System Interrupts," on page 49.
For a list of all HBI related pins, refer to Table 3.4 on page 30 in Chapter 3, Pin Description and
Configuration.
8.2
Host Memory Mapping
The host memory map has two unique modes: normal operation mode, and direct FIFO access mode.
During normal operation, the base address decode map is as described in Figure 14.1 on page 166,
allowing access to the full range of System Management CSRs and the TX/RX Data and Status FIFOs.
This is the default mode of operation. The second mode of operation is the direct FIFO access mode.
In direct FIFO access mode, all host write operations are to the TX Data FIFO and all host read
operations are from the RX Data FIFO. Refer to Section 14.1.3, "Direct FIFO Access Mode," on
page 167 for additional information.
8.3
Host Endianess
The LAN9312 supports big and little endian host byte ordering based upon the END_SEL pin. When
END_SEL is low, host access is little endian. When END_SEL is high, host access is big endian. In a
typical application, END_SEL is connected to a high-order address line, making endian selection
address based. This highly flexible interface provides mixed endian access for registers and memory
for both PIO and host DMA access. As an example, PIO transfers to/from the System CSRs can utilize
a different byte ordering than host DMA transactions to/from the RX and TX Data FIFOs.
All internal busses are 32-bit with little endian byte ordering. Logic within the host bus interface reorders bytes based on the state of the endian select signal (END_SEL).
SMSC LAN9312
99
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Data path operations for the supported endian configurations are illustrated in Figure 8.1, "Little Endian
Byte Ordering" and Figure 8.2, "Big Endian Byte Ordering".
.
32-BIT LITTLE ENDIAN
(END_SEL = 0)
INTERNAL ORDER
MSB
31
LSB
24
23
16
15
8
7
0
3
2
1
0
3
2
1
0
31
24
23
16
15
8
7
0
HOST DATA BUS
Figure 8.1 Little Endian Byte Ordering
.
32-BIT BIG ENDIAN
(END_SEL = 1)
INTERNAL ORDER
MSB
31
31
LSB
24
23
16
15
8
7
0
3
2
1
0
0
1
2
3
24
23
16
15
8
7
0
HOST DATA BUS
Figure 8.2 Big Endian Byte Ordering
Revision 2.0 (02-14-13)
100
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
8.4
Host Interface Timing
This section details the characteristics and special restrictions of the various supported host cycles.
For detailed timing specifications on supported PIO read/write operations, refer to Section 15.5, "AC
Specifications". The LAN9312 supports the following host cycles:
Read Cycles:

PIO Reads (nCS or nRD controlled)

PIO Burst Reads (nCS or nRD controlled)

RX Data FIFO Direct PIO Reads (nCS or nRD controlled)

RX Data FIFO Direct PIO Burst Reads (nCS or nRD controlled)
Write Cycles:

PIO Writes (nCS or nWR controlled)

TX Data FIFO Direct PIO Writes (nCS or nWR controlled)
8.4.1
Special Situations
8.4.1.1
Reset Ending During a Read Cycle
If a reset condition terminates during an active read cycle, the tail end of the read cycle will be ignored
by the LAN9312.
8.4.1.2
Writes Following a Reset
Following any reset, writes from the host bus are ignored until after a read cycle is performed.
8.4.2
Special Restrictions on Back-to Back Write-Read Cycles
It is important to note that there are specific restrictions on the timing of back-to-back host write-read
operations. These restrictions concern reading the host control registers after any write cycle to the
LAN9312. In some cases there is a delay between writing to the LAN9312, and the subsequent side
effect (change in the control register value). For example, when writing to the TX Data FIFO, it takes
up to 135ns for the level indication to change in the TX FIFO Information Register (TX_FIFO_INF).
In order to prevent the host from reading stale data after a write operation, minimum wait periods have
been established. These periods are specified in Table 8.1. The host processor is required to wait the
specified period of time after any write to the LAN9312 before reading the resource specified in the
table. These wait periods are for read operations that immediately follow any write cycle. Note that the
required wait period is dependant upon the register being read after the write.
Performing “dummy” reads of the Byte Order Test Register (BYTE_TEST) register is a convenient way
to guarantee that the minimum write-to-read timing restriction is met. Table 8.1 shows the number of
dummy reads that are required before reading the register indicated. The number of BYTE_TEST
reads in this table is based on the minimum timing for Tcyc (45ns). For microprocessors with slower
busses the number of reads may be reduced as long as the total time is equal to, or greater than the
time specified in the table. Note that dummy reads of the BYTE_TEST register are not required as
long as the minimum time period is met.
SMSC LAN9312
101
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 8.1 Read After Write Timing Rules
REGISTER NAME
MINIMUM WAIT TIME FOR
READ FOLLOWING ANY
WRITE CYCLE (IN NS)
NUMBER OF BYTE_TEST
READS
(ASSUMING TCYC OF 45NS)
RX Data FIFO
0
0
RX Status FIFO
0
0
RX Status FIFO PEEK
0
0
TX Status FIFO
0
0
TX Status FIFO PEEK
0
0
ID_REV
0
0
IRQ_CFG
135
3
INT_STS
90
2
INT_EN
45
1
BYTE_TEST
0
0
FIFO_INT
45
1
RX_CFG
45
1
TX_CFG
45
1
HW_CFG
45
1
RX_DP_CTRL
45
1
RX_FIFO_INF
0
0
TX_FIFO_INF
135
3
PMT_CTRL
315
7
GPT_CFG
45
1
GPT_CNT
135
3
FREE_RUN
180
4
RX_DROP
0
0
MAC_CSR_CMD
45
1
MAC_CSR_DATA
45
1
AFC_CFG
45
1
1588_CLOCK_HI_RX_CAPTURE_1
0
0
1588_CLOCK_LO_RX_CAPTURE_1
0
0
1588_SEQ_ID_SRC_UUID_HI_RX_CAPTURE_1
0
0
1588_SRC_UUID_LO_RX_CAPTURE_1
0
0
1588_CLOCK_HI_TX_CAPTURE_1
0
0
Revision 2.0 (02-14-13)
102
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 8.1 Read After Write Timing Rules (continued)
REGISTER NAME
MINIMUM WAIT TIME FOR
READ FOLLOWING ANY
WRITE CYCLE (IN NS)
NUMBER OF BYTE_TEST
READS
(ASSUMING TCYC OF 45NS)
1588_CLOCK_LO_TX_CAPTURE_1
0
0
1588_SEQ_ID_SRC_UUID_HI_TX_CAPTURE_1
0
0
1588_SRC_UUID_LO_TX_CAPTURE_1
0
0
1588_CLOCK_HI_RX_CAPTURE_2
0
0
1588_CLOCK_LO_RX_CAPTURE_2
0
0
1588_SEQ_ID_SRC_UUID_HI_RX_CAPTURE_2
0
0
1588_SRC_UUID_LO_RX_CAPTURE_2
0
0
1588_CLOCK_HI_TX_CAPTURE_2
0
0
1588_CLOCK_LO_TX_CAPTURE_2
0
0
1588_SEQ_ID_SRC_UUID_HI_TX_CAPTURE_2
0
0
1588_SRC_UUID_LO_TX_CAPTURE_2
0
0
1588_CLOCK_HI_RX_CAPTURE_MII
0
0
1588_CLOCK_LO_RX_CAPTURE_MII
0
0
1588_SEQ_ID_SRC_UUID_HI_RX_CAPTURE_MII
0
0
1588_SRC_UUID_LO_RX_CAPTURE_MII
0
0
1588_CLOCK_HI_TX_CAPTURE_MII
0
0
1588_CLOCK_LO_TX_CAPTURE_MII
0
0
1588_SEQ_ID_SRC_UUID_HI_TX_CAPTURE_MII
0
0
1588_SRC_UUID_LO_TX_CAPTURE_MII
0
0
1588_CLOCK_HI_CAPTURE_GPIO_8
0
0
1588_CLOCK_LO_CAPTURE_GPIO_8
0
0
1588_CLOCK_HI_CAPTURE_GPIO_9
0
0
1588_CLOCK_LO_CAPTURE_GPIO_9
0
0
1588_CLOCK_HI
45
1
1588_CLOCK_LO
45
1
1588_CLOCK_ADDEND
45
1
1588_CLOCK_TARGET_HI
45
1
1588_CLOCK_TARGET_LO
45
1
1588_CLOCK_TARGET_RELOAD_HI
45
1
1588_CLOCK_TARGET_RELOAD_LO
45
1
1588_AUX_MAC_HI
45
1
SMSC LAN9312
103
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 8.1 Read After Write Timing Rules (continued)
REGISTER NAME
MINIMUM WAIT TIME FOR
READ FOLLOWING ANY
WRITE CYCLE (IN NS)
NUMBER OF BYTE_TEST
READS
(ASSUMING TCYC OF 45NS)
1588_AUX_MAC_LO
45
1
1588_CONFIG
45
1
1588_INT_STS_EN
45
1
MANUAL_FC_1
45
1
MANUAL_FC_2
45
1
MANUAL_FC_MII
45
1
SWITCH_CSR_DATA
45
1
SWITCH_CSR_CMD
45
1
E2P_CMD
45
1
E2P_DATA
45
1
LED_CFG
45
1
VPHY_BASIC_CTRL
45
1
VPHY_BASIC_STATUS
45
1
VPHY_ID_MSB
45
1
VPHY_ID_LSB
45
1
VPHY_AN_ADV
45
1
VPHY_AN_LP_BASE_ABILITY
45
1
VPHY_AN_EXP
45
1
VPHY_SPECIAL_CONTROL_STATUS
45
1
GPIO_CFG
45
1
GPIO_DATA_DIR
45
1
GPIO_INT_STS_EN
45
1
SWITCH_MAC_ADDRH
45
1
SWITCH_MAC_ADDRL
45
1
RESET_CTL
45
1
SWITCH_CSR_DIRECT_DATA
NA
NA
Revision 2.0 (02-14-13)
104
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
8.4.3
Special Restrictions on Back-to-Back Read Cycles
There are also restrictions on specific back-to-back host read operations. These restrictions concern
reading specific registers after reading a resource that has side effects. In many cases there is a delay
between reading the LAN9312, and the subsequent indication of the expected change in the control
and status register values.
In order to prevent the host from reading stale data on back-to-back reads, minimum wait periods have
been established. These periods are specified in Table 8.2. The host processor is required to wait the
specified period of time between read operations of specific combinations of resources. The wait period
is dependant upon the combination of registers being read.
Performing “dummy” reads of the Byte Order Test Register (BYTE_TEST) register is a convenient way
to guarantee that the minimum wait time restriction is met. Table 8.2 below also shows the number of
dummy reads that are required for back-to-back read operations. The number of BYTE_TEST reads
in this table is based on the minimum timing for Tcyc (45ns). For microprocessors with slower busses
the number of reads may be reduced as long as the total time is equal to, or greater than the time
specified in the table. Dummy reads of the BYTE_TEST register are not required as long as the
minimum time period is met.
Table 8.2 Read After Read Timing Rules
AFTER READING...
WAIT FOR THIS MANY
NANOSECONDS...
OR PERFORM THIS MANY
READS OF BYTE_TEST…
(ASSUMING TCYC OF 45NS)
BEFORE READING...
RX Data FIFO
135
3
RX_FIFO_INF
RX Status FIFO
135
3
RX_FIFO_INF
TX Status FIFO
135
3
TX_FIFO_INF
RX_DROP
180
4
RX_DROP
SWITCH_CSR_DATA
45
1
SWITCH_CSR_CMD
Note 8.1
VPHY_AN_EXP
45
1
VPHY_AN_EXP
Note 8.1
SMSC LAN9312
This timing applies only to the auto-increment and auto-decrement modes of Switch Fabric
CSR register access.
105
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
8.4.4
PIO Reads
PIO reads can be used to access System CSR’s or RX Data and RX/TX Status FIFOs. PIO reads can
be performed using Chip Select (nCS) or Read Enable (nRD). A PIO Read cycle begins when both
nCS and nRD are asserted. Either or both of these control signals must de-assert between cycles for
the period specified in Table 15.8, “PIO Read Cycle Timing Values,” on page 447. The cycle ends when
either or both nCS and nRD are de-asserted. They may be asserted and de-asserted in any order.
Read data is valid as indicated in the functional timing diagram in Figure 8.3.
The endian select signal (END_SEL) has the same timing characteristics as the address lines.
Please refer to Section 15.5.4, "PIO Read Cycle Timing," on page 447 for the AC timing specifications
for PIO read operations.
Note: Some registers have restrictions on the timing of back-to-back write-read cycles. Please refer
to Section 8.4.2 for information on these restrictions.
END_SEL
VALID
A[x:2]
VALID
nCS, nRD
D[31:0] (OUTPUT)
VALID
Figure 8.3 Functional Timing for PIO Read Operation
Revision 2.0 (02-14-13)
106
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
8.4.5
PIO Burst Reads
In this mode, performance is improved by allowing up to 8 DWORD read cycles back-to-back. PIO
burst reads can be performed using Chip Select (nCS) or Read Enable (nRD). A PIO Burst Read
begins when both nCS and nRD are asserted. Either or both of these control signals must de-assert
between bursts for the period specified in Table 15.9, “PIO Burst Read Cycle Timing Values,” on
page 448. The burst cycle ends when either or both nCS and nRD are de-asserted. They may be
asserted and de-asserted in any order. Read data is valid as indicated in the functional timing diagram
in Figure 8.4.
Note: Fresh data is supplied each time A[2] toggles.
The endian select signal (END_SEL) has the same timing characteristics as the upper address lines.
Please refer to Section 15.5.5, "PIO Burst Read Cycle Timing," on page 448 for the AC timing
specifications for PIO burst read operations.
Note: PIO burst reads are only supported for the RX Data FIFO. Burst reads from other registers are
not supported.
END_SEL
VALID
A[x:5]
VALID
A[4:2]
VALID
VALID
VALID
VALID
nCS, nRD
D[31:0] (OUTPUT)
VALID
VALID
VALID
VALID
Figure 8.4 Functional Timing for PIO Burst Read Operation
SMSC LAN9312
107
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
8.4.6
RX Data FIFO Direct PIO Reads
In this mode only A[2] is decoded, and any read of the LAN9312 will read the RX Data FIFO. This
mode is enabled when FIFO_SEL is driven high during a read access. This is normally accomplished
by connecting the FIFO_SEL signal to a high-order address line. This mode is useful when the host
processor must increment its address when accessing the LAN9312.
Timing is identical to a PIO read and the FIFO_SEL and END_SEL signals have the same timing
characteristics as the address lines. An RX Data FIFO direct PIO read cycle begins when both nCS
and nRD are asserted. Either or both of these control signals must de-assert between cycles for the
period specified in Table 15.10, “RX Data FIFO Direct PIO Read Cycle Timing Values,” on page 449.
The cycle ends when either or both nCS and nRD are de-asserted. These signals may be asserted
and de-asserted in any order. Read data is valid as indicated in the functional timing diagram in
Figure 8.5.
Note:
A[9:3] are ignored during RX Data FIFO direct PIO reads.
Please refer to Section 15.5.6, "RX Data FIFO Direct PIO Read Cycle Timing," on page 449 for the
AC timing specifications for RX Data FIFO direct PIO read operations.
FIFO_SEL
END_SEL
VALID
A[x:3]
A[2]
VALID
nCS, nRD
D[31:0] (OUTPUT)
VALID
(READ DATA FROM RX DATA FIFO)
Figure 8.5 Functional Timing for RX Data FIFO Direct PIO Read Operation
Revision 2.0 (02-14-13)
108
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
8.4.7
RX Data FIFO Direct PIO Burst Reads
In this mode only A[2] is decoded, and any burst read of the LAN9312 will read the RX Data FIFO.
This mode is enabled when FIFO_SEL is driven high during a read access. This is normally
accomplished by connecting the FIFO_SEL signal to a high-order address line. This mode is useful
when the host processor must increment its address when accessing the LAN9312. Timing is identical
to a PIO burst read, and the FIFO_SEL and END_SEL signals have the same timing characteristics
as the address lines.
In this mode, performance is improved by allowing an unlimited number of back-to-back DWORD read
cycles. RX Data FIFO direct PIO burst reads can be performed using chip select (nCS) or read enable
(nRD). An RX Data FIFO direct PIO burst read begins when both nCS and nRD are asserted. Either
or both of these control signals must de-assert between bursts for the period specified in Table 15.11,
“RX Data FIFO Direct PIO Burst Read Cycle Timing Values,” on page 450. The burst cycle ends when
either or both nCS and nRD are de-asserted. They may be asserted and de-asserted in any order.
Read data is valid as indicated in the functional timing diagram in Figure 8.6.
Note: Fresh data is supplied each time A[2] toggles.
Please refer to Section 15.5.7, "RX Data FIFO Direct PIO Burst Read Cycle Timing," on page 450 for
the AC timing specifications for PIO RX Data FIFO direct PIO burst read operations.
FIFO_SEL
END_SEL
A[x:3]
A[2]
nCS, nRD
D[31:0] (OUTPUT)
(READ DATA FROM RX DATA FIFO)
Figure 8.6 Functional Timing for RX Data FIFO Direct PIO Burst Read Operation
SMSC LAN9312
109
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
8.4.8
PIO Writes
PIO writes are used for all LAN9312 write cycles. PIO writes can be performed using Chip Select (nCS)
or Write Enable (nWR). A PIO write cycle begins when both nCS and nWR are asserted. The cycle
ends when either or both nCS and nWR are de-asserted. Either or both of these control signals must
de-assert between cycles for the period specified in Table 15.12, “PIO Write Cycle Timing Values,” on
page 451. They may be asserted and de-asserted in any order. Either or both of these control signals
must be de-asserted between cycles for the period specified. The PIO write cycle is illustrated in the
functional timing diagram in Figure 8.7.
The END_SEL signal has the same timing characteristics as the address lines.
Please refer to Section 15.5.8, "PIO Write Cycle Timing," on page 451 for the AC timing specifications
for PIO write operations.
END_SEL
VALID
A[x:2]
VALID
nCS, nWR
D[31:0] (INPUT)
VALID
Figure 8.7 Functional Timing for PIO Write Operation
Revision 2.0 (02-14-13)
110
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
8.4.9
TX Data FIFO Direct PIO Writes
In this mode only A[2] is decoded, and any write to the LAN9312 will write the TX Data FIFO. This
mode is enabled when FIFO_SEL is driven high during a write access. This is normally accomplished
by connecting the FIFO_SEL signal to a high-order address line. This mode is useful when the host
processor must increment its address when accessing the LAN9312.
Timing is identical to a PIO write, and the FIFO_SEL and END_SEL signals have the same timing
characteristics as the address lines. A TX Data FIFO direct PIO write cycle begins when both nCS and
nWR are asserted. Either or both of these control signals must de-assert between cycles for the period
specified in Table 15.13, “TX Data FIFO Direct PIO Write Cycle Timing Values,” on page 452. The cycle
ends when either or both nCS and nWR are de-asserted. They may be asserted and de-asserted in
any order. The TX Data FIFO direct PIO write cycle is illustrated in the functional timing diagram in
Figure 8.8.
Note:
A[9:3] are ignored during TX Data FIFO direct PIO writes.
Please refer to Section 15.5.9, "TX Data FIFO Direct PIO Write Cycle Timing," on page 452 for the AC
timing specifications for TX Data FIFO direct PIO write operations.
FIFO_SEL
END_SEL
VALID
A[x:3]
A[2]
VALID
nCS, nWR
D[31:0] (INPUT)
VALID
(WRITE DATA TO TX DATA FIFO)
Figure 8.8 Functional Timing for TX Data FIFO Direct PIO Write Operation
8.5
HBI Interrupts
The HBI allows access to all interrupt configuration and status registers within the LAN9312. The
LAN9312 implements a multi-tier interrupt hierarchy with the Interrupt Configuration Register
(IRQ_CFG), Interrupt Status Register (INT_STS), and Interrupt Enable Register (INT_EN) at the top
level. These registers allow for the configuration of which interrupts trigger the IRQ, as well as the IRQ
deassertion and polarity properties. Interrupts may be generated from the 1588 Timestamping, Switch
Fabric, Port 1 PHY, Port 2 PHY, Host MAC, EEPROM Loader, General Purpose Timer, General
Purpose I/O, and Power Management blocks.
For more information of the LAN9312 interrupts, refer to Chapter 5, System Interrupts.
SMSC LAN9312
111
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 9 Host MAC
9.1
Functional Overview
The Host MAC incorporates the essential protocol requirements for operating an Ethernet/IEEE 802.3compliant node and provides an interface between the Host Bus Interface (HBI) and the Ethernet PHYs
and Switch Fabric. On the front end, the Host MAC interfaces to the HBI via 2 sets of FIFO’s (TX Data
FIFO, TX Status FIFO, RX Data FIFO, RX Status FIFO). An additional bus is used to access the Host
MAC CSR’s via the Host MAC CSR Interface Command Register (MAC_CSR_CMD) and Host MAC
CSR Interface Data Register (MAC_CSR_DATA) system registers.
The receive and transmit FIFO’s allow increased packet buffer storage to the Host MAC. The FIFOs
are a conduit between the HBI and the Host MAC through which all transmitted and received data and
status information is passed. Deep FIFOs allow a high degree of latency tolerance relative to the
various transport and OS software stacks reducing and minimizing overrun conditions. Both the Host
MAC and the TX/RX FIFOs have separate receive and transmit data paths.
The Host MAC can store up to 250 Ethernet packets utilizing FIFOs, totaling 16KB, with a packet
granularity of 4 bytes. This memory is shared by the RX and TX blocks and is configurable in terms
of allocation via the Hardware Configuration Register (HW_CFG) register to the ranges described in
Section 9.7.3, "FIFO Memory Allocation Configuration". This depth of buffer storage minimizes or
eliminates receive overruns.
On the back end, the Host MAC interfaces with the 10/100 Ethernet PHY’s (Virtual PHY, Port 1 PHY,
Port 2 PHY) via an internal SMI (Serial Management Interface) bus. This allows the Host MAC access
to the PHY’s internal registers via the Host MAC MII Access Register (HMAC_MII_ACC) and Host
MAC MII Data Register (HMAC_MII_DATA). The Host MAC interfaces to the Switch Engine Port 0 via
an internal MII (Media Independent Interface) connection allowing for incoming and outgoing Ethernet
packet transfers.
The Host MAC can operate at either 100Mbps or 10Mbps in both half-duplex or full-duplex modes.
When operating in half-duplex mode, the Host MAC complies fully with Section 4 of ISO/IEC 8802-3
(ANSI/IEEE standard) and ANSI/IEEE 802.3 standards. When operating in full-duplex mode, the Host
MAC complies with IEEE 802.3 full-duplex operation standard.
The Host MAC provides programmable enhanced features designed to minimize host supervision, bus
utilization, and pre- or post-message processing. These features include the ability to disable retries
after a collision, dynamic Frame Check Sequence (FCS) generation on a frame-by-frame basis,
automatic pad field insertion and deletion to enforce minimum frame size attributes, and automatic
retransmission and detection of collision frames. The Host MAC can sustain transmission or reception
of minimally-sized back-to-back packets at full line speed with an interpacket gap (IPG) of 9.6
microseconds for 10 Mbps and 0.96 microseconds for 100 Mbps.
The primary attributes of the Host MAC are:

Transmit and receive message data encapsulation

Framing (frame boundary delimitation, frame synchronization)

Error detection (physical medium transmission errors)

Media access management

Medium allocation (collision detection, except in full-duplex operation)

Contention resolution (collision handling, except in full-duplex operation)

Flow control during full-duplex mode

Decoding of control frames (PAUSE command) and disabling the transmitter

Generation of control frames

Interface between the Host Bus Interface and the Ethernet PHYs/Switch Fabric.
Revision 2.0 (02-14-13)
112
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
9.2
Flow Control
The Host MAC supports full-duplex flow control using the pause operation and control frame. Halfduplex flow control using back pressure is also supported. The Host MAC flow control is configured
via the memory mapped Host MAC Automatic Flow Control Configuration Register (AFC_CFG) located
in the System CSR space and the Host MAC Flow Control Register (HMAC_FLOW) located in the
Host MAC CSR space.
Note: The Host MAC controls the flow between the switch fabric and the Host MAC, not the network
flow control. The switch fabric handles the network flow control independently.
9.2.1
Full-Duplex Flow Control
In full-duplex mode, flow control is achieved via the pause operation and the transmission of control
frames. The pause operation inhibits transmission of data frames for a specified period of time. A
pause operation consists of a frame containing the globally assigned multicast address (01-80-C2-0000-01), the PAUSE opcode, and a parameter indicating the quantum of slot time (512 bit times) to
inhibit data transmissions. The PAUSE parameter may range from 0 to 65,535 slot times. The Host
MAC logic, upon receiving a frame with the reserved multicast address and PAUSE opcode, inhibits
data frame transmissions for the length of time indicated. If a pause request is received while a
transmission is in progress, the pause will take effect after the transmission is complete. Control frames
are received, processed by the Host MAC, and passed on.
The Host MAC also has the capability of transmitting control frames (pause command) via hardware
and software control. The software driver requests the Host MAC to transmit a control frame and gives
the value of the PAUSE time to be used in the control frame. The Host MAC function constructs a
control frame by setting the appropriate values in the corresponding fields (as defined in the 802.3
specification) and transmits the frame to the internal MII interface. The transmission of the control
frame is not affected by the current state of the Pause timer value that may be set due to a recently
received control frame.
9.2.2
Half-Duplex Flow Control (Backpressure)
In half-duplex mode, back pressure is used for flow control. Whenever the receive buffer/FIFO
becomes full or crosses a certain threshold level, the Host MAC starts sending a jam signal. The Host
MAC transmit logic enters a state at the end of current transmission (if any), where it waits for the
beginning of a received frame. Once a new frame starts, the Host MAC starts sending the jam signal,
which will result in a collision. After sensing the collision, the remote station will back off its
transmission. The Host MAC continues sending the jam to make other stations defer transmission. The
Host MAC only generates this collision-based back pressure when it receives a new frame, in order
to avoid any late collisions.
9.3
Virtual Local Area Network (VLAN) Support
Virtual Local Area Networks (VLANs), as defined within the IEEE 802.3 standard, provide network
administrators a means of grouping nodes within a larger network into broadcast domains. To
implement a VLAN, four extra bytes are added to the basic Ethernet packet. As shown in Figure 9.1,
the four bytes are inserted after the Source Address Field and before the Type/Length field. The first
two bytes of the VLAN tag identify the tag, and by convention are set to the value 0x8100. The last
two bytes identify the specific VLAN associated with the packet and provide a priority field.
The LAN9312 supports VLAN-tagged packets and provides two Host MAC registers, Host MAC VLAN1
Tag Register (HMAC_VLAN1) and Host MAC VLAN2 Tag Register (HMAC_VLAN2), which are used
to identify VLAN-tagged packets. The HMAC_VLAN1 register is used to specify the VLAN1 tag which
will increase the legal frame length from 1518 to 1522 bytes. The HMAC_VLAN2 register is used to
specify the VLAN2 tag which will increase the legal frame length from 1518 to 1538 bytes. If a packet
arrives bearing either of these tags in the two bytes succeeding the Source Address field, the controller
will recognize the packet as a VLAN-tagged packet, allowing the packet to be received and processed
SMSC LAN9312
113
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
by the host software. If both VLAN1 and VLAN2 tag Identifiers are used, each should be unique. If
both are set to the same value, VLAN1 is given higher precedence and the maximum legal frame
length is set to 1522.
Standard Ethernet Frame (1518 Bytes)
Preamble
7 Bytes
SOF
1 Byte
Dest. Addr.
6 Bytes
Source Addr.
6 Bytes
Type
2 Bytes
Data
46-1500 Bytes
FCS
4 Bytes
Ethernet Frame with VLAN TAG (1522 Bytes)
Preamble
7 Bytes
SOF
1 Byte
Dest. Addr.
6 Bytes
Source Addr.
6 Bytes
TPID
2 Bytes
Type
2 Bytes
Type
2 Bytes
Data
46-1500 Bytes
FCS
4 Bytes
Tag Control Information
(TCI)
TPID
2 Bytes
User Priority CFI
3 Bits
1 Bit
VLAN ID
12 Bits
Defines the VLAN to
which the frame belongs
Canonical Address Format Indicator
Indicates the frame’s priority
Tag Protocol ID: \x81-00
Figure 9.1 VLAN Frame
9.4
Address Filtering
The Ethernet address fields of an Ethernet packet consist of two 6-byte fields: one for the destination
address and one for the source address. The first bit of the destination address signifies whether it is
a physical address or a multicast address.
The Host MAC address check logic filters the frame based on the Ethernet receive filter mode that has
been enabled. The various filter modes of the Host MAC are specified based on the state of the control
bits in the Host MAC Control Register (HMAC_CR), as shown in Table 9.1. Please refer to the Section
14.3.1, "Host MAC Control Register (HMAC_CR)," on page 271 for more information on this register.
If the frame fails the filter, the Host MAC does not receive the packet. The host has the option of
accepting or ignoring the packet.
Note: This filtering function is performed after any switch fabric filtering functions. The user must
ensure the switch filtering is setup properly to allow packets to be passed to the Host MAC for
further filtering.
Revision 2.0 (02-14-13)
114
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 9.1 Address Filtering Modes
MCPAS
PRMS
INVFILT
HO
HPFILT
DESCRIPTION
0
0
0
0
0
MAC address perfect filtering only
for all addresses.
0
0
0
0
1
MAC address perfect filtering for
physical address and hash filtering
for multicast addresses
0
0
0
1
1
Hash Filtering for physical and
multicast addresses
0
0
1
0
0
Inverse Filtering
X
1
0
X
X
Promiscuous
1
0
0
0
X
Pass all multicast frames. Frames
with physical addresses are
perfect-filtered
1
0
0
1
1
Pass all multicast frames. Frames
with physical addresses are hashfiltered
9.4.1
Perfect Filtering
This filtering mode passes only incoming frames whose destination address field exactly matches the
value programmed into the Host MAC Address High Register (HMAC_ADDRH) and the Host MAC
Address Low Register (HMAC_ADDRL). The MAC address is formed by the concatenation of these
two registers.
9.4.2
Hash Only Filtering
This type of filtering checks for incoming receive packets (from switch Port 0) with either multicast or
physical destination addresses, and executes an imperfect address filtering against the hash table. The
hash table is formed by merging the values in the Host MAC Multicast Hash Table High Register
(HMAC_HASHH) and the Host MAC Multicast Hash Table Low Register (HMAC_HASHL) to form a
64-bit hash table.
During imperfect hash filtering, the upper 6-bits of the destination address of the incoming frame are
used to index the contents of the hash table. The most significant bit of the destination address
determines the register to be used (HMAC_HASHH or HMAC_HASHL), while the other five bits
determine the bit within the register. A value of 00000 selects Bit 0 of the HMAC_HASHL register and
a value of 11111 selects Bit 31 of the HMAC_HASHH register.
9.4.3
Hash Perfect Filtering
In hash perfect filtering, if the received frame is a physical address, the Host MAC packet filter will
perfect-filter the incoming frame’s destination field with the value programmed into the Host MAC
Address High Register (HMAC_ADDRH) and the Host MAC Address Low Register (HMAC_ADDRL).
However, if the incoming frame is a multicast frame, the Host MAC packet filter function performs an
imperfect address filtering against the hash table.
The imperfect filtering against the hash table is the same imperfect filtering process described in
Section 9.4.2, "Hash Only Filtering".
SMSC LAN9312
115
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
9.4.4
Inverse Filtering
In inverse filtering, the Host MAC packet filter accepts incoming frames (from switch Port 0) with a
destination address not matching the perfect address (i.e., the value programmed into the Host MAC
Address High Register (HMAC_ADDRH) and the Host MAC Address Low Register (HMAC_ADDRL))
and rejects frames with destination addresses matching the perfect address.
For all filtering modes, when the MCPAS bit of the Host MAC Control Register (HMAC_CR) is set, all
multicast frames are accepted. When the PRMS bit is set, all frames are accepted regardless of their
destination address. This includes all broadcast frames as well.
9.5
Wake-up Frame Detection
Setting the Wake-Up Frame Enable bit (WUEN) in the Host MAC Wake-up Control and Status Register
(HMAC_WUCSR), places the Host MAC in the wake-up frame detection mode. In this mode, normal
data reception is disabled, and detection logic within the Host MAC examines received data for the
pre-programmed wake-up frame patterns. The Host MAC can be programmed to notify the host of the
wake-up frame detection with the assertion of the host interrupt (IRQ) or power management event
(PME) signal. Upon detection, the Wake-Up Frame Received bit (WUFR) in the HMAC_WUCSR
register is set. When the host clears the WUEN bit, the Host MAC will resume normal receive
operation.
Before putting the Host MAC into the wake-up frame detection state, the host must provide the
detection logic with a list of sample frames and their corresponding byte masks. This information must
be written into the Host MAC Wake-up Frame Filter Register (HMAC_WUFF). The wake-up frame filter
is configured through this register using an index mechanism. After power-on reset, hardware reset,
or soft reset, the Host MAC loads the first value written to the HMAC_WUFF register to the first
DWORD in the wake-up frame filter (filter 0 byte mask). The second value written to this register is
loaded to the second DWORD in the wake-up frame filter (filter 1 byte mask) and so on for all eight
DWORDs. The wake-up frame filter functionally is described below.
The Host MAC supports four programmable wake-up filters that support many different receive packet
patterns. If remote wake-up mode is enabled, the remote wake-up function receives all frames
addressed to the Host MAC. It then checks each frame against the enabled filter and recognizes the
frame as a remote wake-up frame if it passes the wakeup frame filter register’s address filtering and
CRC value match.
In order to determine which bytes of the frames should be checked by the CRC module, the Host MAC
uses a programmable byte mask and a programmable pattern offset for each of the four supported
filters.
The pattern’s offset defines the location of the first byte that should be checked in the frame. Since
the destination address is checked by the address filtering function, the pattern offset is always greater
than 12.
The byte mask is a 31-bit field that specifies whether or not each of the 31 contiguous bytes within
the frame, beginning in the pattern offset, should be checked. If bit j in the byte mask is set, the
detection logic checks byte offset +j in the frame. In order to load the wake-up frame filter, the host
must perform eight writes to the Host MAC Wake-up Frame Filter Register (HMAC_WUFF). Table 9.2
shows the wake-up frame filter register’s structure.
Note: The switch fabric must be configured to pass wake-up packets to the Host MAC for this function
to operate properly.
Note: When wake-up frame detection is enabled via the WUEN bit of the Host MAC Wake-up Control
and Status Register (HMAC_WUCSR), a broadcast wake-up frame will wake-up the device
despite the state of the Disable Broadcast Frames (BCAST) bit in the Host MAC Control
Register (HMAC_CR).
Revision 2.0 (02-14-13)
116
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 9.2 Wake-Up Frame Filter Register Structure
Filter 0 Byte Mask
Filter 1 Byte Mask
Filter 2 Byte Mask
Filter 3 Byte Mask
Reserved
Filter 3
Command
Reserved
Filter 3 Offset
Filter 2
Command
Reserved
Filter 2 Offset
Filter 1
Command
Filter 1Offset
Reserved
Filter 0
Command
Filter 0 Offset
Filter 1 CRC-16
Filter 0 CRC-16
Filter 3 CRC-16
Filter 2 CRC-16
The Filter i Byte Mask defines which incoming frame bytes Filter i will examine to determine whether
or not this is a wake-up frame. Table 9.3, describes the byte mask’s bit fields.
Table 9.3 Filter i Byte Mask Bit Definitions
FILTER I BYTE MASK DESCRIPTION
FIELD
DESCRIPTION
31
Must be zero (0)
30:0
Byte Mask: If bit j of the byte mask is set, the CRC machine processes byte number pattern - (offset
+ j) of the incoming frame. Otherwise, byte pattern - (offset + j) is ignored.
The Filter i command register controls Filter i operation. Table 9.4 shows the Filter i command register.
Table 9.4 Filter i Command Bit Definitions
FILTER i COMMANDS
FIELD
3
2:1
0
SMSC LAN9312
DESCRIPTION
Address Type: Defines the destination address type of the pattern. When bit is set, the pattern
applies only to multicast frames. When bit is cleared, the pattern applies only to unicast frames.
RESERVED
Enable Filter: When bit is set, Filter i is enabled, otherwise, Filter i is disabled.
117
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
The Filter i Offset register defines the offset in the frame’s destination address field from which the
frames are examined by Filter i. Table 9.5 describes the Filter i Offset bit fields.
Table 9.5 Filter i Offset Bit Definitions
FILTER i OFFSET DESCRIPTION
FIELD
7:0
DESCRIPTION
Pattern Offset: The offset of the first byte in the frame on which CRC is checked for wake-up frame
recognition. The minimum value of this field must be 12 since there should be no CRC check for
the destination address and the source address fields. The Host MAC checks the first offset byte
of the frame for CRC and checks to determine whether the frame is a wake-up frame. Offset 0 is
the first byte of the incoming frame's destination address.
The Filter i CRC-16 register contains the CRC-16 result of the frame that should pass Filter i.
Table 9.6 describes the Filter i CRC-16 bit fields.
Table 9.6 Filter i CRC-16 Bit Definitions
FILTER i CRC-16 DESCRIPTION
FIELD
15:0
9.5.1
DESCRIPTION
Pattern CRC-16: This field contains the 16-bit CRC value from the pattern and the byte mask
programmed to the wake-up filter register function. This value is compared against the CRC
calculated on the incoming frame, and a match indicates the reception of a wakeup frame.
Magic Packet Detection
Setting the Magic Packet Enable bit (MPEN) in the Host MAC Wake-up Control and Status Register
(HMAC_WUCSR) places the Host MAC in the “Magic Packet” detection mode. In this mode, normal
data reception is disabled, and detection logic within the Host MAC examines received data for a Magic
Packet. The LAN9312 can be programmed to notify the host of the “Magic Packet” detection with the
assertion of the host interrupt (IRQ) or power management event signal (PME). Upon detection, the
Magic Packet Received bit (MPR) in the HMAC_WUCSR register is set. When the host clears the
MPEN bit, the Host MAC will resume normal receive operation. Please refer to Section 14.3.12, "Host
MAC Wake-up Control and Status Register (HMAC_WUCSR)," on page 285 for additional information
on this register.
In Magic Packet mode, the Host MAC constantly monitors each frame addressed to the node for a
specific Magic Packet pattern. Only packets matching the Host MAC address or broadcast address are
checked for the Magic Packet requirements. Once the address requirement has been met, the Host
MAC checks the received frame for the pattern 48’hFF_FF_FF_FF_FF_FF after the destination and
source address field. The Host MAC then looks in the frame for 16 repetitions of the Host MAC address
without any breaks or interruptions. In case of a break in the 16 address repetitions, the Host MAC
again scans for the 48'hFF_FF_FF_FF_FF_FF pattern in the incoming frame. The 16 repetitions may
be anywhere in the frame but must be preceded by the synchronization stream. The device will also
accept a multicast frame, as long as it detects the 16 duplications of the Host MAC address.
Revision 2.0 (02-14-13)
118
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
For example, if the Host MAC address is 00h 11h 22h 33h 44h 55h, then the MAC scans for the
following data sequence in an Ethernet frame:
Destination Address Source Address ……………FF FF FF FF FF FF
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55 00 11 22 33 44 55
…CRC
Note: The switch fabric must be configured to pass magic packets to the Host MAC for this function
to operate properly.
9.6
Host MAC Address
The Host MAC address is configured via the Host MAC Address Low Register (HMAC_ADDRL) and
Host MAC Address High Register (HMAC_ADDRH). These registers contain the 48-bit physical
address of the Host MAC. The contents of these registers may be loaded directly by the host, or
optionally, by the EEPROM Loader from EEPROM at power-on (if a programmed EEPROM is
detected). The MAC address value loaded by the EEPROM Loader into the Host MAC address
registers (for host packet unicast qualification), is also loaded into the Switch Fabric MAC address
registers (for pause packet / flow control): Switch Fabric MAC Address Low Register
(SWITCH_MAC_ADDRL) and Switch Fabric MAC Address High Register (SWITCH_MAC_ADDRH).
These two sets of registers are loaded simultaneously via the same EEPROM byte addresses.
Table 9.7 below illustrates the byte ordering of the HMAC_ADDRL/SWITCH_MAC_ADDRL and
HMAC_ADDRH/SWITCH_MAC_ADDRH registers with respect to the reception of the Ethernet
physical address. Also shown is the correlation between the EEPROM addresses and
HMAC_ADDRL/SWITCH_MAC_ADDRL and HMAC_ADDRH/SWITCH_MAC_ADDRH registers.
Table 9.7 EEPROM Byte Ordering and Register Correlation
EEPROM Address
Register Locations Written
Order of Reception on Ethernet
01h
HMAC_ADDRL[7:0]
SWITCH_MAC_ADDRL[7:0]
1st
02h
HMAC_ADDRL[15:8]
SWITCH_MAC_ADDRL[15:8]
2nd
03h
HMAC_ADDRL[23:16]
SWITCH_MAC_ADDRL[23:16]
3rd
04h
HMAC_ADDRL[31:24]
SWITCH_MAC_ADDRL[31:24]
4th
05h
HMAC_ADDRH[7:0]
SWITCH_MAC_ADDRH[7:0]
5th
06h
HMAC_ADDRH[15:8]
SWITCH_MAC_ADDRH[15:8]
6th
For example, if the desired Ethernet physical address is 12-34-56-78-9A-BC, the HMAC_ADDRL and
HMAC_ADDRH registers would be programmed as shown in Figure 9.2. The values required to
automatically load this configuration from the EEPROM are also shown.
SMSC LAN9312
119
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
31
24 23
xx
16 15
xx
8 7
BCh
0
9Ah
HMAC_ADDRH / SWITCH_MAC_ADDRH
31
24 23
78h
16 15
56h
8 7
34h
0
12h
HMAC_ADDRL / SWITCH_MAC_ADDRL
06h
BCh
05h
9Ah
04h
78h
03h
56h
02h
34h
01h
12h
00h
A5h
EEPROM
Figure 9.2 Example EEPROM MAC Address Setup
Note: By convention, the right nibble of the left most byte of the Ethernet address (in this example,
the 2 of the 12h) is the most significant nibble and is transmitted/received first.
For more information on the EEPROM and EEPROM Loader, refer to Section 10.2, "I2C/Microwire
Master EEPROM Controller," on page 137.
9.7
FIFOs
The LAN9312 contains four host-accessible FIFOs (TX Status, RX Status, TX Data, and RX Data) and
two internal inaccessible Host MAC TX/RX MIL FIFO’s (TX MIL FIFO, RX MIL FIFO).
9.7.1
TX/RX FIFOs
The TX/RX Data and Status FIFOs store the incoming and outgoing address and data information,
acting as a conduit between the host bus interface (HBI) and the Host MAC. The sizes of these FIFOs
are configurable via the Hardware Configuration Register (HW_CFG) register to the ranges described
in Table 9.8. Refer to Section 9.7.3, "FIFO Memory Allocation Configuration" for additional information.
The the RX and TX FIFOs related register definitions can be found in section Section 14.2.2, "Host
MAC & FIFO’s".
The TX and RX Data FIFOs have the base address of 00h and 20h respectively. However, each FIFO
is also accessible at seven additional contiguous memory locations, as can be seen in Figure 14.1.
The Host may access the TX or RX Data FIFOs at any of these alias port locations, as they all function
identically and contain the same data. This alias port addressing is implemented to allow hosts to burst
through sequential addresses.
The TX and RX Status FIFOs can each be read from two register locations; the Status FIFO Port, and
the Status FIFO PEEK. The TX and RX Status FIFO Ports (48h and 40h respectively) will perform a
destructive read, popping the data from the TX or RX Status FIFO. The TX and RX Status FIFO PEEK
register locations (4Ch and 44h respectively) allow a non-destructive read of the top (oldest) location
of the FIFOs.
Proper use of the The TX/RX Data and Status FIFOs, including the correct data formatting is described
in detail in Section 9.8, "TX Data Path Operation," on page 122 and Section 9.9, "RX Data Path
Operation," on page 132.
9.7.2
MIL FIFOs
The MAC Interface Layer (MIL), within the Host MAC, contains a 2KB transmit and a 128 Byte receive
FIFO which are separate from the TX and RX FIFOs. These MIL FIFOs are not directly accessible
from the HBI. The differentiation between the TX/RX FIFOs and the TX/RX MIL FIFOs is that once the
transmit or receive packets are in the MIL FIFOs, the host no longer can control or access the TX or
RX data. The MIL FIFOs are essentially the working buffers of the Host MAC logic. In the case of
Revision 2.0 (02-14-13)
120
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
reception, the data must be moved into the RX FIFOs before the host can access the data. For TX
operations, the MIL operates in store-and-forward mode and will queue an entire frame before
beginning transmission.
As space in the TX MIL FIFO frees, data is moved into it from the TX Data FIFO. Depending on the
size of the frames to be transmitted, the Host MAC can hold up to two Ethernet frames. This is in
addition to any TX data that may be queued in the TX Data FIFO.
Conversely, as data is received, it is moved from the Host MAC to the RX MIL FIFO, and then into
the RX Data FIFO. When the RX Data FIFO fills up, data will continue to collect in the RX MIL FIFO.
If the RX MIL FIFO fills up and overruns, subsequent RX frames will be lost until room is made in the
RX Data FIFO. For each frame of data that is lost, the Host MAC RX Dropped Frames Counter
Register (RX_DROP) is incremented.
RX and TX MIL FIFO levels are not visible to the host processor and operate independent of the
TX/RX FIFOs. FIFO levels set for the TX/RX Data and Status FIFOs do not take into consideration the
MIL FIFOs.
9.7.3
FIFO Memory Allocation Configuration
TX and RX FIFO space is configurable through the Hardware Configuration Register (HW_CFG). The
user must select the FIFO allocation by setting the TX FIFO Size (TX_FIF_SZ) field in the Hardware
Configuration Register (HW_CFG). The TX_FIF_SZ field selects the total allocation for the TX data
path, including the TX Status FIFO size. The TX Status FIFO size is fixed at 512 Bytes (128 TX Status
DWORDs). The TX Status FIFO length is subtracted from the total TX FIFO size with the remainder
being the TX Data FIFO Size. The minimum size of the TX FIFOs is 2KB (TX Data and TX Status
FIFOs combined). Note that TX Data FIFO space includes both commands and payload data.
RX FIFO Size is the remainder of the unallocated FIFO space (16384 bytes – TX FIFO Size). The RX
Status FIFO size is always equal to 1/16 of the RX FIFO size. The RX Status FIFO length is subtracted
from the total RX FIFO size with the remainder being the RX Data FIFO Size.
For example, if TX_FIF_SZ = 6 then:
Total TX FIFO Size = 6144 Bytes (6KB)
TX Status FIFO Size = 512 Bytes (Fixed)
TX Data FIFO Size = 6144 – 512 = 5632 Bytes
RX FIFO Size = 16384 – 6144 = 10240 Bytes (10KB)
RX Status FIFO Size = 10240 / 16 = 640 Bytes (160 RX Status DWORDs)
RX Data FIFO Size = 10240 – 640 = 9600 Bytes
Table 9.8 contains an overview of the configurable TX/RX FIFO sizes and defaults. Table 9.9 shows
every valid setting for the TX_FIF_SZ field and the resulting FIFO sizes. Note that settings not shown
in this table are reserved and should not be used.
Note: The RX Data FIFO is considered full 4 DWORDs before the length that is specified in the
HW_CFG register.
Table 9.8 TX/RX FIFO Configurable Sizes
FIFO
SIZE RANGE
DEFAULT
TX Status
RX Status
TX Data
RX Data
512
128-892
1536-13824
1920-13440
512
704
4608
10560
SMSC LAN9312
121
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 9.9 Valid TX/RX FIFO Allocations
9.8
TX_FIF_SZ
TX DATA FIFO
SIZE (BYTES)
TX STATUS FIFO
SIZE (BYTES)
RX DATA FIFO
SIZE (BYTES)
RX STATUS FIFO
SIZE (BYTES)
2
1536
512
13440
896
3
2560
512
12480
832
4
3584
512
11520
768
5
4608
512
10560
704
6
5632
512
9600
640
7
6656
512
8640
576
8
7680
512
7680
512
9
8704
512
6720
448
10
9728
512
5760
384
11
10752
512
4800
320
12
11776
512
3840
256
13
12800
512
2880
192
14
13824
512
1920
128
TX Data Path Operation
Data is queued for transmission by writing it into the TX Data FIFO. Each packet to be transmitted
may be divided among multiple buffers. Each buffer starts with a two DWORD TX command (TX
command ‘A’ and TX command ‘B’). The TX command instructs the LAN9312 on the handling of the
associated buffer. Packet boundaries are delineated using control bits within the TX command.
The host provides a 16-bit Packet Tag field in the TX command. The Packet Tag value is appended
to the corresponding TX status DWORD. All Packet Tag fields must have the same value for all buffers
in a given packet. If tags differ between buffers in the same packet the TXE error will be asserted. Any
value may be chosen for a Packet Tag as long as all tags in the same Packet are identical. Packet
Tags also provide a method of synchronization between transmitted packets and their associated
status. Software can use unique Packet Tags to assist with validating matching status completions.
Note: The use of Packet Tags is not required by the hardware. This field can be used by the LAN
software driver for any application. Packet Tags is only one application example.
The Packet Length field in the TX command specifies the number of bytes in the associated packet.
All Packet Length fields must have the same value for all buffers in a given packet. Hardware
compares the Packet Length field and the actual amount of data received by the Ethernet controller.
If the actual packet length count does not match the Packet Length field as defined in the TX
command, the Transmitter Error (TXE) flag is asserted.
The LAN9312 can be programmed to start payload transmission of a buffer on a byte boundary by
setting the “Data Start Offset” field in the TX command. The “Data Start Offset” field points to the actual
start of the payload data within the first 8 DWORDs of the buffer. Data before the “Data Start Offset”
pointer will be ignored. When a packet is split into multiple buffers, each successive buffer may begin
on any arbitrary byte.
Revision 2.0 (02-14-13)
122
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
The LAN9312 can be programmed to strip padding from the end of a transmit packet in the event that
the end of the packet does not align with the host burst boundary. This feature is necessary when the
LAN9312 is operating in a system that always performs multi-word bursts. In such cases the LAN9312
must guarantee that it can accept data in multiples of the Burst length regardless of the actual packet
length. When configured to do so, the LAN9312 will accept extra data at the end of the packet and
will remove the extra padding before transmitting the packet. The LAN9312 automatically removes data
up to the boundary specified in the Buffer End Alignment field specified in each TX command.
The host can instruct the LAN9312 to issue an interrupt when the buffer has been fully loaded into the
TX FIFO contained in the LAN9312 and transmitted. This feature is enabled through the TX command
‘Interrupt on Completion’ field.
Upon completion of transmission, irrespective of success or failure, the status of the transmission is
written to the TX Status FIFO. TX status is available to the host and may be read using PIO operations.
An interrupt can be optionally enabled by the host to indicate the availability of a programmable
number TX status DWORDS.
Before writing the TX command and payload data to the TX FIFO, the host must check the available
TX FIFO space by performing a PIO read of the TX FIFO Information Register (TX_FIFO_INF). The
host must ensure that it does not overfill the TX FIFO or the TX Error (TXE) flag will be asserted.
The host proceeds to write the TX command by first writing TX command ‘A’, then TX command ‘B’.
After writing the command, the host can then move the payload data into the TX FIFO. TX status
DWORDs are stored in the TX Status FIFO to be read by the host at a later time upon completion of
the data transmission onto the wire.
Figure 9.3 Simplified Host TX Flow Diagram
SMSC LAN9312
123
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
9.8.1
TX Buffer Format
TX buffers exist in the host’s memory in a given format. The host writes a TX command word into the
TX data buffer before moving the Ethernet packet data. The TX command A and command B are 32bit values that are used by the LAN9312 in the handling and processing of the associated Ethernet
packet data buffer. Buffer alignment, segmentation and other packet processing parameters are
included in the command structure. The buffer format is illustrated in Figure 9.4.
Host Write
31
Order
0
1st
TX Command 'A'
2nd
TX Command 'B'
3rd
Optional offset DWORD0
.
.
.
Optional offset DWORDn
Offset + Data DWORD0
.
.
.
.
.
Last Data & PAD
Optional Pad DWORD0
.
.
.
Optional Pad DWORDn
Last
Figure 9.4 TX Buffer Format
Figure 9.4 shows the TX Buffer as it is written into the LAN9312. It should be noted that not all of the
data shown in this diagram is actually stored in the TX Data FIFO. This must be taken into account
when calculating the actual TX Data FIFO usage. Please refer to Section 9.8.5, "Calculating Actual TX
Data FIFO Usage" for a detailed explanation on calculating the actual TX Data FIFO usage.
9.8.2
TX Command Format
The TX command instructs the TX FIFO controller on handling the subsequent buffer. The command
precedes the data to be transmitted. The TX command is divided into two, 32-bit words; TX command
‘A’ and TX command ‘B’.
There is a 16-bit Packet Tag in the TX command ‘B’ command word. Packet Tags may, if host software
desires, be unique for each packet (i.e., an incrementing count). The value of the tag will be returned
in the TX status word for the associated packet. The Packet tag can be used by host software to
uniquely identify each status word as it is returned to the host.
Revision 2.0 (02-14-13)
124
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Both TX command ‘A’ and TX command ‘B’ are required for each buffer in a given packet. TX
command ‘B’ must be identical for every buffer in a given packet. If the TX command ‘B’ words do not
match, the Ethernet controller will assert the Transmitter Error (TXE) flag.
9.8.2.1
TX Command ‘A’
Table 9.10 TX Command 'A' Format
BITS
31
DESCRIPTION
Interrupt on Completion (IOC). When set, the TX_IOC bit will be asserted in the Interrupt Status
Register (INT_STS) when the current buffer has been fully loaded into the TX FIFO.
30:26
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
25:24
Buffer End Alignment. This field specifies the alignment that must be maintained on the last data
transfer of a buffer. The host will add extra DWORDs of data up to the alignment specified in the
table below. The LAN9312 will remove the extra DWORDs. This mechanism can be used to maintain
cache line alignment on host processors.
[25]
[24]
End Alignment
0
0
4-byte alignment
0
1
16-byte alignment
1
0
32-byte alignment
1
1
Reserved
23:21
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility
20:16
Data Start Offset (bytes). This field specifies the offset of the first byte of TX data. The offset value
can be anywhere from 0 bytes to a 31 byte offset.
15:14
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility
13
First Segment (FS). When set, this bit indicates that the associated buffer is the first segment of the
packet.
12
Last Segment. When set, this bit indicates that the associated buffer is the last segment of the
packet
11
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
10:0
Buffer Size (bytes). This field indicates the number of bytes contained in the buffer following this
command. This value, along with the Buffer End Alignment field, is read and checked by the
LAN9312 and used to determine how many extra DWORDs were added to the end of the Buffer. A
running count is also maintained in the LAN9312 of the cumulative buffer sizes for a given packet.
This cumulative value is compared against the Packet Length field in the TX command ‘B’ word and
if they do not correlate, the TXE flag is set.
Note:
SMSC LAN9312
The buffer size specified does not include the buffer end alignment padding or data start
offset added to a buffer.
125
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
9.8.2.2
TX Command ‘B’
Table 9.11 TX Command 'B' Format
BITS
DESCRIPTION
31:16
Packet Tag. The host should write a unique packet identifier to this field. This identifier is added to
the corresponding TX status word and can be used by the host to correlate TX status words with
their corresponding packets.
Note:
15:14
The use of packet tags is not required by the hardware. This field can be used by the LAN
software driver for any application. Packet Tags is one application example.
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
13
Add CRC Disable. When set, the automatic addition of the CRC is disabled.
12
Disable Ethernet Frame Padding. When set, this bit prevents the automatic addition of padding to
an Ethernet frame of less than 64 bytes. The CRC field is also added despite the state of the Add
CRC Disable field.
11
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
10:0
Packet Length (bytes). This field indicates the total number of bytes in the current packet. This
length does not include the offset or padding. If the Packet Length field does not match the actual
number of bytes in the packet the Transmitter Error (TXE) flag will be set.
9.8.3
TX Data Format
The TX data section begins at the third DWORD in the TX buffer (after TX command ‘A’ and TX
command ‘B’). The location of the first byte of valid buffer data to be transmitted is specified in the
“Data Start Offset” field of the TX command ‘A’ word. Table 9.12, "TX DATA Start Offset", shows the
correlation between the setting of the LSB’s in the “Data Start Offset” field and the byte location of the
first valid data byte. Additionally, transmit buffer data can be offset by up to 7 additional DWORDS as
indicated by the upper three MSB’s (5:2) in the “Data Start Offset” field.
Table 9.12 TX DATA Start Offset
Data Start Offset [1:0]:
First TX Data Byte:
11
D[31:24]
10
D[23:16]
01
D[15:8]
00
D[7:0]
TX data is contiguous until the end of the buffer. The buffer may end on a byte boundary. Unused
bytes at the end of the packet will not be sent to the Host MAC Interface Layer for transmission.
The Buffer End Alignment field in TX command ‘A’ specifies the alignment that must be maintained for
the associated buffer. End alignment may be specified as 4-, 16-, or 32-byte. The host processor is
responsible for adding the additional data to the end of the buffer. The hardware will automatically
remove this extra data.
9.8.3.1
TX Buffer Fragmentation Rules
Transmit buffers must adhere to the following rules:

Each buffer can start and end on any arbitrary byte alignment

The first buffer of any transmit packet can be any length

Middle buffers (i.e., those with First Segment = Last Segment = 0) must be greater than, or equal
to 4 bytes in length

The final buffer of any transmit packet can be any length
Revision 2.0 (02-14-13)
126
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
The MIL operates in store-and-forward mode and has specific rules with respect to fragmented
packets. The total space consumed in the TX MIL FIFO must be limited to no more than 2KB - 3
DWORDs (2,036 bytes total). Any transmit packet that is so highly fragmented that it takes more space
than this must be un-fragmented (by copying to a driver-supplied buffer) before the transmit packet
can be sent to the LAN9312.
One approach to determine whether a packet is too fragmented is to calculate the actual amount of
space that it will consume, and check it against 2,036 bytes. Another approach is to check the number
of buffers against a worst-case limit of 86 (see explanation below).
9.8.3.2
Calculating Worst-Case TX MIL FIFO Usage
The actual space consumed by a buffer in the TX MIL FIFO consists only of any partial DWORD offsets
in the first/last DWORD of the buffer, plus all of the whole DWORDs in between. Any whole DWORD
offsets and/or alignments are stripped off before the buffer is loaded into the TX Data FIFO, and TX
command words are stripped off before the buffer is written to the TX MIL FIFO, so none of those
DWORDs count as space consumed. The worst-case overhead for a TX buffer is 6 bytes, which
assumes that it started on the high byte of a DWORD and ended on the low byte of a DWORD. A TX
packet consisting of 86 such fragments would have an overhead of 516 bytes (6 * 86) which, when
added to a 1514-byte max-size transmit packet (1516 bytes, rounded up to the next whole DWORD),
would give a total space consumption of 2,032 bytes, leaving 4 bytes to spare; this is the basis for the
"86 fragment" rule mentioned above. For more information on the MIL FIFO’s refer to Section 9.7.2,
"MIL FIFOs," on page 120.
9.8.4
TX Status Format
TX status is passed to the host CPU through a separate FIFO mechanism. A status word is returned
for each packet transmitted. Data transmission is suspended if the TX Status FIFO becomes full. Data
transmission will resume when the host reads the TX status and there is room in the FIFO for more
“TX Status” data.
The host can optionally choose to not read the TX status. The TX status can be ignored by setting the
“TX Status Discard Allow Overrun Enable” (TXSAO) bit in the Transmit Configuration Register
(TX_CFG). If this option is chosen TX status will not be written to the FIFO. Setting this bit high allows
the transmitter to continue operation with a full TX Status FIFO. In this mode the status information is
still available in the TX Status FIFO, and TX status interrupts still function. In the case of an overrun,
the TXSUSED counter will stay at zero and no further TX status will be written to the TX Status FIFO
until the host frees space by reading TX status. If TXSAO is enabled, a TXE error will not be generated
if the TX Status FIFO overruns. In this mode the host is responsible for re-synchronizing TX status in
the case of an overrun.
Note: Though the Host MAC is communicating locally with the switch fabric MAC, the events
described in the TX Status word may still occur.
BITS
DESCRIPTION
31:16
Packet TAG. Unique identifier written by the host into the Packet Tag field of the TX command ‘B’
word. This field can be used by the host to correlate TX status words with the associated TX packets.
15
Error Status (ES). When set, this bit indicates that the Ethernet controller has reported an error. This
bit is the logical OR of bits 11, 10, 9, 8, 2, 1 in this status word.
14:12
Reserved. These bits are reserved. Always write zeros to this field to guarantee future compatibility.
11
Loss of Carrier. When set, this bit indicates the loss of carrier during transmission.
10
No Carrier. When set, this bit indicates that the carrier signal from the transceiver was not present
during transmission.
SMSC LAN9312
127
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
9
Late Collision. When set, indicates that the packet transmission was aborted after the collision
window of 64 bytes.
8
Excessive Collisions. When set, this bit indicates that the transmission was aborted after 16
collisions while attempting to transmit the current packet.
7
Reserved. This bit is reserved. Always write zeros to this field to guarantee future compatibility.
6:3
Collision Count. This counter indicates the number of collisions that occurred before the packet was
transmitted. It is not valid when excessive collisions (bit 8) is also set.
2
Excessive Deferral. If the deferred bit is set in the control register, the setting of the excessive
deferral bit indicates that the transmission has ended because of a deferral of over 24288 bit times
during transmission.
1
Reserved. This bit is reserved. Always write zeros to this field to guarantee future compatibility
0
Deferred. When set, this bit indicates that the current packet transmission was deferred.
9.8.5
Calculating Actual TX Data FIFO Usage
The following rules are used to calculate the actual TX Data FIFO space consumed by a TX Packet:

TX command 'A' is stored in the TX Data FIFO for every TX buffer

TX command 'B' is written into the TX Data FIFO when the First Segment (FS) bit is set in TX
command 'A'

Any DWORD-long data added as part of the “Data Start Offset” is removed from each buffer before
the data is written to the TX Data FIFO. Any data that is less than 1 DWORD is passed to the TX
Data FIFO.

Payload from each buffer within a Packet is written into the TX Data FIFO.

Any DWORD-long data added as part of the End Padding is removed from each buffer before the
data is written to the TX Data FIFO. Any end padding that is less than 1 DWORD is passed to the
TX Data FIFO
9.8.6
Transmit Examples
9.8.6.1
TX Example 1
In this example a single, 111-Byte Ethernet packet will be transmitted. This packet is divided into three
buffers. The three buffers are as follows:
Buffer 0:

7-Byte “Data Start Offset”

79-Bytes of payload data

16-Byte “Buffer End Alignment”
Buffer 1:

0-Byte “Data Start Offset”

15-Bytes of payload data

16-Byte “Buffer End Alignment”
Buffer 2:

10-Byte “Data Start Offset”

17-Bytes of payload data

16-Byte “Buffer End Alignment”
Revision 2.0 (02-14-13)
128
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Figure 9.5 illustrates the TX command structure for this example, and also shows how data is passed
to the TX Data FIFO.
Data Written to the
Memory Mapped
TX Data FIFO Port
31
TX Command 'A'
Buffer End Alignment = 1
Data Start Offset = 7
First Segment = 1
Last Segment = 0
Buffer Size = 79
0
TX Command 'A'
Data Passed to the
TX Data FIFO
TX Command 'B'
7-Byte Data Start Offset
TX Command 'A'
TX Command 'B'
Packet Length = 111
TX Command 'B'
79-Byte Payload
79-Byte Payload
Pad DWORD 1
10-Byte
End Padding
TX Command 'A'
31
TX Command 'A'
Buffer End Alignment = 1
Data Start Offset = 0
First Segment = 0
Last Segment = 0
Buffer Size = 15
0
TX Command 'A'
15-Byte Payload
TX Command 'B'
TX Command 'A'
15-Byte Payload
TX Command 'B'
Packet Length = 111
1B
17-Byte Payload
31
TX Command 'A'
Buffer End Alignment = 1
Data Start Offset = 10
First Segment = 0
Last Segment = 1
Buffer Size = 17
0
10-Byte
TX Offset
Command
'A'
End
Padding
TX Command 'B'
10-Byte
Data Start Offset
NOTE: Extra bytes
between buffers are
not transmitted
TX Command 'B'
Packet Length = 111
17-Byte Payload Data
5-Byte End Padding
Figure 9.5 TX Example 1
SMSC LAN9312
129
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
9.8.6.2
TX Example 2
In this example, a single 183-Byte Ethernet packet will be transmitted. This packet is in a single buffer
as follows:

2-Byte “Data Start Offset”

183-Bytes of payload data

4-Byte “Buffer End Alignment”
Figure 9.6 illustrates the TX command structure for this example, and also shows how data is passed
to the TX Data FIFO. Note that the packet resides in a single TX Buffer, therefore both the FS and LS
bits are set in TX command ‘A’.
Data Written to the
Memory Mapped
TX Data FIFO Port
TX Command 'A'
Buffer End Alignment = 0
Data Start Offset = 6
First Segment = 1
Last Segment = 1
Buffer Size =183
31
Data Passed to the
TX Data FIFO
0
TX Command 'A'
TX Command 'A'
TX Command 'B'
TX Command 'B'
6-Byte Data Start Offset
TX Command 'B'
Packet Length = 183
183-Byte Payload Data
183-Byte Payload Data
3B End Padding
NOTE: Extra bytes between buffers
are not transmitted
Figure 9.6 TX Example 2
Revision 2.0 (02-14-13)
130
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
9.8.7
Transmitter Errors
If the Transmitter Error (TXE) flag is asserted for any reason, the transmitter will continue operation.
TX Error (TXE) will be asserted under the following conditions:
9.8.8

If the actual packet length count does not match the Packet Length field as defined in the TX
command.

Both TX command ‘A’ and TX command ‘B’ are required for each buffer in a given packet. TX
command ‘B’ must be identical for every buffer in a given packet. If the TX command ‘B’ words do
not match, the Ethernet controller will assert the Transmitter Error (TXE) flag.

Host overrun of the TX Data FIFO.

Overrun of the TX Status FIFO (unless TXSAO is enabled)
Stopping and Starting the Transmitter
To halt the transmitter, the host must set the STOP_TX bit in the Transmit Configuration Register
(TX_CFG). The transmitter will finish sending the current frame (if there is a frame transmission in
progress). When the transmitter has received the TX status for this frame, it will clear the STOP_TX
and TX_ON bits, and will pulse the TXSTOP_INT in the Interrupt Status Register (INT_STS).
Once stopped, the host can optionally clear the TX Status and TX Data FIFOs. The host must reenable the transmitter by setting the TX_ON bit. If the there are frames pending in the TX Data FIFO
(i.e., TX Data FIFO was not purged), the transmission will resume with this data.
SMSC LAN9312
131
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
9.9
RX Data Path Operation
When an Ethernet Packet is received, the Host MAC Interface Layer (MIL) first begins to transfer the
RX data. This data is loaded into the RX Data FIFO. The RX Data FIFO pointers are updated as data
is written into the FIFO.
The last transfer from the MIL is the RX status word. The LAN9312 implements a separate FIFO for
the RX status words. The total available RX data and status queued in the RX FIFO can be read from
the RX FIFO Information Register (RX_FIFO_INF). The host may read any number of available RX
status words before reading the RX Data FIFO.
The host must use caution when reading the RX data and status. The host must never read more data
than what is available in the FIFO’s. If this is attempted an underrun condition will occur. If this error
occurs, the Ethernet controller will assert the Receiver Error (RXE) interrupt. If an underrun condition
occurs, a soft reset is required to regain host synchronization.
A configurable beginning offset is supported in the LAN9312. The RX data Offset field in the Receive
Configuration Register (RX_CFG) controls the number of bytes that the beginning of the RX data buffer
is shifted. The host can set an offset from 0-31 bytes. The offset may be changed in between RX
packets, but it must not be changed during an RX packet read.
The LAN9312 can be programmed to add padding at the end of a receive packet in the event that the
end of the packet does not align with the host burst boundary. This feature is necessary when the
LAN9312 is operating in a system that always performs multi-DWORD bursts. In such cases the
LAN9312 must guarantee that it can transfer data in multiples of the Burst length regardless of the
actual packet length. When configured to do so, the LAN9312 will add extra data at the end of the
packet to allow the host to perform the necessary number of reads so that the Burst length is not cut
short. Once a packet has been padded by the H/W, it is the responsibility of the host to interrogate the
packet length field in the RX status and determine how much padding to discard at the end of the
packet.
It is possible to read multiple packets out of the RX Data FIFO in one continuous stream. It should be
noted that the programmed Offset and Padding will be added to each individual packet in the stream,
since packet boundaries are maintained.
9.9.1
RX Slave PIO Operation
Using PIO mode, the host can either implement a polling or interrupt scheme to empty the received
packet out of the RX Data FIFO. The host will remain in the idle state until it receives an indication
(interrupt or polling) that data is available in the RX Data FIFO. The host will then read the RX Status
FIFO to get the packet status, which will contain the packet length and any other status information.
The host should perform the proper number of reads, as indicated by the packet length plus the start
offset and the amount of optional padding added to the end of the frame, from the RX Data FIFO. A
typical host receive routine using interrupts can be seen in Figure 9.7, while a typical host receive
routine using polling can be seen in Figure 9.8.
Revision 2.0 (02-14-13)
132
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
init
Idle
RX Interrupt
Read RX
Status
DWORD
Not Last Packet
Last Packet
Read RX
Packet
Figure 9.7 Host Receive Routine Using Interrupts
init
Read
RX_FIFO_INF
Valid Status DWORD
Read RX
Status
DWORD
Not Last Packet
Last Packet
Read RX
Packet
Figure 9.8 Host Receive Routine Using Polling
SMSC LAN9312
133
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
9.9.1.1
Receive Data FIFO Fast Forward
The RX data path implements an automatic data discard function. Using the RX Data FIFO Fast
Forward bit (RX_FFWD) in the Receive Datapath Control Register (RX_DP_CTRL), the host can
instruct the LAN9312 to skip the packet at the head of the RX Data FIFO. The RX Data FIFO pointers
are automatically incremented to the beginning of the next RX packet.
When performing a fast-forward, there must be at least 4 DWORDs of data in the RX Data FIFO for
the packet being discarded. For cases with less than 4 DWORDs, do not use RX_FFWD. In this case
data must be read from the RX Data FIFO and discarded using standard PIO read operations.
After initiating a fast-forward operation, do not perform any reads of the RX Data FIFO until the
RX_FFWD bit is cleared. Other resources can be accessed during this time (i.e., any registers and/or
the other three FIFO’s). Also note that the RX_FFWD will only fast-forward the RX Data FIFO, not the
RX Status FIFO. After an RX fast-forward operation the RX status must still be read from the RX Status
FIFO.
The receiver does not have to be stopped to perform a fast-forward operation.
9.9.1.2
Force Receiver Discard (Receiver Dump)
In addition to the Receive data Fast Forward feature, LAN9312 also implements a receiver "dump"
feature. This feature allows the host processor to flush the entire contents of the RX Data and RX
Status FIFOs. When activated, the read and write pointers for the RX Data and Status FIFO’s will be
returned to their reset state. To perform a receiver dump, the LAN9312 receiver must be halted. Once
the receiver stop completion is confirmed, the RX_DUMP bit can be set in the Receive Configuration
Register (RX_CFG). The RX_DUMP bit is cleared when the dump is complete. For more information
on stopping the receiver, please refer to Section 9.9.4, "Stopping and Starting the Receiver". For more
information on the RX_DUMP bit, please refer to Section 14.2.2.1, "Receive Configuration Register
(RX_CFG)," on page 180.
9.9.2
RX Packet Format
The RX status words can be read from the RX Status FIFO port, while the RX data packets can be
read from the RX Data FIFO. RX data packets are formatted in a specific manner before the host can
Revision 2.0 (02-14-13)
134
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
read them as shown in Figure 9.9. It is assumed that the host has previously read the associated
status word from the RX Status FIFO, to ascertain the data size and any error conditions.
Host Read
Order
31
0
1st
Optional offset DWORD0
2nd
.
.
Optional offset DWORDn
ofs + First Data DWORD
.
.
.
.
Last Data DWORD
Optional Pad DWORD0
.
.
Last
Optional Pad DWORDn
Figure 9.9 RX Packet Format
9.9.3
RX Status Format
Note: Though the Host MAC is communicating locally with the switch fabric MAC, the events
described in the RX Status word may still occur.
BITS
DESCRIPTION
31
Reserved. This bit is reserved. Reads 0.
30
Filtering Fail. When set, this bit indicates that the associated frame failed the address recognizing
filtering.
29:16
Packet Length. The size, in bytes, of the corresponding received frame.
15
Error Status (ES). When set this bit indicates that the Host MAC Interface Layer (MIL) has reported
an error. This bit is the Internal logical “or” of bits 11,7,6 and 1.
14
Reserved. These bits are reserved. Reads 0.
13
Broadcast Frame. When set, this bit indicates that the received frame has a Broadcast address.
12
Length Error (LE). When set, this bit indicates that the actual length does not match with the
length/type field of the received frame.
11
Runt Frame. When set, this bit indicates that frame was prematurely terminated before the collision
window (64 bytes). Runt frames are passed on to the host only if the Pass Bad Frames bit (PASSBAD)
of the Host MAC Control Register (HMAC_CR) is set.
10
Multicast Frame. When set, this bit indicates that the received frame has a Multicast address.
9:8
Reserved. These bits are reserved. Reads 0.
SMSC LAN9312
135
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
7
Frame Too Long. When set, this bit indicates that the frame length exceeds the maximum Ethernet
specification of 1518 bytes. This is only a frame too long indication and will not cause the frame
reception to be truncated.
6
Collision Seen. When set, this bit indicates that the frame has seen a collision after the collision
window. This indicates that a late collision has occurred.
5
Frame Type. When set, this bit indicates that the frame is an Ethernet-type frame (Length/Type field
in the frame is greater than 1500). When reset, it indicates the incoming frame was an 802.3 type
frame. This bit is not set for Runt frames less than 14 bytes.
4
Receive Watchdog time-out. When set, this bit indicates that the incoming frame is greater than
2048 bytes through 2560 bytes, therefore expiring the Receive Watchdog Timer.
3
MII Error. When set, this bit indicates that a receive error was detected during frame reception.
2
Dribbling Bit. When set, this bit indicates that the frame contained a non-integer multiple of 8 bits.
This error is reported only if the number of dribbling bits in the last byte is at least 3 in the 10 Mbps
operating mode. This bit will not be set when the collision seen bit[6] is set. If set and the CRC error
bit is [1] reset, then the packet is considered to be valid.
1
CRC Error. When set, this bit indicates that a CRC error was detected. This bit is also set when the
RX_ER pin is asserted during the reception of a frame even though the CRC may be correct. This bit
is not valid if the received frame is a Runt frame, or a late collision was detected or when the
Watchdog Time-out occurs.
0
Reserved. These bits are reserved. Reads 0
9.9.4
Stopping and Starting the Receiver
To stop the receiver, the host must clear the RXEN bit in the Host MAC Control Register (HMAC_CR).
When the receiver is halted, the RXSTOP_INT will be pulsed and reflected in the Interrupt Status
Register (INT_STS). Once stopped, the host can optionally clear the RX Status and RX Data FIFOs.
The host must re-enable the receiver by setting the RXEN bit.
9.9.5
Receiver Errors
If the Receiver Error (RXE) flag is asserted in the Interrupt Status Register (INT_STS) for any reason,
the receiver will continue operation. RX Error (RXE) will be asserted under the following conditions:

A host underrun of RX Data FIFO

A host underrun of the RX Status FIFO

An overrun of the RX Status FIFO
It is the duty of the host to identify and resolve any error conditions.
Revision 2.0 (02-14-13)
136
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 10 Serial Management
10.1
Functional Overview
This chapter details the LAN9312 serial management functionality of the I2C/Microwire EEPROM
Controller and the supporting EEPROM Loader.
The I2C/Microwire EEPROM controller is an I2C/Microwire master module which interfaces an optional
external EEPROM with the system register bus and the EEPROM Loader. Multiple types
(I2C/Microwire) and sizes of external EEPROMs are supported. Configuration of the EEPROM type
and size are accomplished via the eeprom_type_strap and eeprom_size_strap[1:0] configuration straps
respectively. Various commands are supported for each EEPROM type, allowing for the storage and
retrieval of static data. The I2C interface conforms to the Philips I2C-Bus Specification.
The EEPROM Loader provides the automatic loading of configuration settings from the EEPROM into
the LAN9312 at reset. The EEPROM Loader module interfaces to the EEPROM Controller, Ethernet
PHYs, and the system CSRs.
10.2
I2C/Microwire Master EEPROM Controller
Based on the configuration strap eeprom_type_strap, the I2C/Microwire EEPROM controller supports
either Microwire or I2C compatible EEPROMs. The I2C/Microwire serial management pins functionality
and characteristics differ dependant on the selected EEPROM type as summarized in Table 10.1.
Table 10.1 I2C/Microwire Master Serial Management Pins Characteristics
EEPROM
TYPE/MODE
I2C Master
EEPROM
Mode
eeprom_type_strap
=1
EE_SDA/EEDI PIN
EEDO PIN
EECS PIN
EE_SDA
NOT USED
NOT USED
EE_SCL
Input enabled
(to I2C master)
Input enabled
(used for straps)
Input enabled
(used for straps)
Open-drain output
(from I2C master)
Output enabled
(driven low)
Output enabled
(driven low)
Input enabled
(to I2C master and
used for straps)
EEDI
EEDO
EECS
EECLK
Input enabled
(to Microwire master)
Input enabled
(used for straps)
Input enabled
(used for straps)
Input enabled
(used for straps)
Output disabled
Output enabled (from
Microwire master)
Output enabled (from
Microwire master)
Output enabled (from
Microwire master)
Pull-down disabled
Microwire
Master
EEPROM
Mode
eeprom_type_strap
=0
EE_SCL/EECLK PIN
Pull-down enabled
Open-drain output
(from I2C master)
Note: When the EEPROM Loader is running, it has exclusive use of the I2C/Microwire EEPROM
controller. Refer to Section 10.2.4, "EEPROM Loader" for more information.
SMSC LAN9312
137
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
10.2.1
EEPROM Controller Operation
I2C and Microwire master EEPROM operations are performed using the EEPROM Command Register
(E2P_CMD) and EEPROM Data Register (E2P_DATA).
In Microwire EEPROM mode, the following operations are supported:

ERASE (Erase Location)

ERAL (Erase All)

EWDS (Erase/Write Disable)

EWEN (Erase/Write Enable)

READ (Read Location)

WRITE (Write Location)

WRAL (Write All)

RELOAD (EEPROM Loader Reload - See Section 10.2.4, "EEPROM Loader")
Note: In I2C EEPROM mode, only a sub-set of the above commands (READ, WRITE, and RELOAD)
are supported.
Note: The EEPROM Loader uses the READ command only.
The supported commands of each mode are detailed in Section 14.2.4.1, "EEPROM Command
Register (E2P_CMD)," on page 197. Details specific to each EEPROM controller mode (I2C and
Microwire) are explained in Section 10.2.2, "I2C EEPROM" and Section 10.2.3, "Microwire EEPROM"
respectively.
When issuing a WRITE, or WRAL command, the desired data must first be written into the EEPROM
Data Register (E2P_DATA). The WRITE or WRAL command may then be issued by setting the
EPC_COMMAND field of the EEPROM Command Register (E2P_CMD) to the desired command
value. If the operation is a WRITE, the EPC_ADDRESS field in the EEPROM Command Register
(E2P_CMD) must also be set to the desired location. The command is executed when the EPC_BUSY
bit of the EEPROM Command Register (E2P_CMD) is set. The completion of the operation is indicated
when the EPC_BUSY bit is cleared.
When issuing a READ command, the EPC_COMMAND and EPC_ADDRESS fields of the EEPROM
Command Register (E2P_CMD) must be configured with the desired command value and the read
address, respectively. The READ command is executed by setting the EPC_BUSY bit of the EEPROM
Command Register (E2P_CMD). The completion of the operation is indicated when the EPC_BUSY
bit is cleared, at which time the data from the EEPROM may be read from the EEPROM Data Register
(E2P_DATA).
Other EEPROM operations (EWDS, EWEN, ERASE, ERAL, RELOAD) are performed by writing the
appropriate command into the EPC_COMMAND field of the EEPROM Command Register
(E2P_CMD). The command is executed by setting the EPC_BUSY bit of the EEPROM Command
Register (E2P_CMD). In all cases, the software must wait for the EPC_BUSY bit to clear before
modifying the EEPROM Command Register (E2P_CMD).
Note: The EEPROM device powers-up in the erase/write disabled state. To modify the contents of
the EEPROM, the EWEN command must first be issued.
If an operation is attempted and the EEPROM device does not respond within 30mS, the LAN9312
will time-out, and the EPC_TIMEOUT bit of the EEPROM Command Register (E2P_CMD) will be set.
Revision 2.0 (02-14-13)
138
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Figure 10.1 illustrates the process required to perform an EEPROM read or write operation.
EEPROM Write
EEPROM Read
Idle
Idle
Write
E2P_DATA
Register
Write
E2P_CMD
Register
Write
E2P_CMD
Register
Read
E2P_CMD
Register
EPC_BUSY = 0
EPC_BUSY = 0
Read
E2P_CMD
Register
Read
E2P_DATA
Register
Figure 10.1 EEPROM Access Flow Diagram
10.2.2
I2C EEPROM
The I2C master implements a low level serial interface (start and stop condition generation, data bit
transmission and reception, acknowledge generation and reception) for connection to I2C EEPROMs,
and consists of a data wire (EE_SDA) and a serial clock (EE_SCL). The serial clock is driven by the
master, while the data wire is bi-directional. Both signals are open-drain and require external pull-up
resistors.
The serial clock is also used as an input as it can be held low by the slave device in order to waitstate the data cycle. Once the slave has data available or is ready to receive, it will release the clock.
Assuming the masters clock low time is also expired, the clock will rise and the cycle will continue. In
the event that the slave device holds the clock low for more than 30mS, the current command
sequence is aborted and the EPC_TIMEOUT bit in the EEPROM Command Register (E2P_CMD) is
set. Both the clock and data signals have Schmitt trigger inputs and digital input filters. The digital filters
reject pulses that are less than 100nS.
Note: Since the I2C master is designed to access EEPROM only, multi-master arbitration is not
supported.
Based on the configuration strap eeprom_size_strap, various sized I2C EEPROMs are supported. The
varying size ranges are supported by additional bits in the address field (EPC_ADDRESS) of the
EEPROM Command Register (E2P_CMD). Within each size range, the largest EEPROM uses all the
address bits, while the smaller EEPROMs treat the upper address bits as don’t cares. The EEPROM
SMSC LAN9312
139
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
controller drives all the address bits as requested regardless of the actual size of the EEPROM. The
supported size ranges for I2C operation are shown in Table 10.2.
Table 10.2 I2C EEPROM Size Ranges
eeprom_size_strap[0]
# OF ADDRESS BYTES
EEPROM SIZE
EEPROM TYPES
0
1 (Note 10.1)
16 x 8 through 2048 x 8
24xx00, 24xx01, 24xx02,
24xx04, 24xx08, 24xx16
1
2
4096 x 8 through 65536 x 8
24xx32, 24xx64, 24xx128,
24xx256, 24xx512
Note 10.1 Bits in the control byte are used as the upper address bits.
The I2C master interface runs at the standard-mode rate of 100KHz and is fully compliant with the
Philips I2C-Bus Specification. Refer to the he Philips I2C-Bus Specification for detailed timing
information.
10.2.2.1
I2C Protocol Overview
I2C is a bi-directional 2-wire data protocol. A device that sends data is defined as a transmitter and a
device that receives data is defined as a receiver. The bus is controlled by a master which generates
the EE_SCL clock, controls bus access, and generates the start and stop conditions. Either the master
or slave may operate as a transmitter or receiver as determined by the master.
The following bus states exist:

Idle: Both EE_SDA and EE_SCL are high when the bus is idle.

Start & Stop Conditions: A start condition is defined as a high to low transition on the EE_ SDA
line while EE_ SCL is high. A stop condition is defined as a low to high transition on the EE_SDA
line while EE_SCL is high. The bus is considered to be busy following a start condition and is
considered free 4.7uS/1.3uS (for 100KHz and 400KHz operation, respectively) following a stop
condition. The bus stays busy following a repeated start condition (instead of a stop condition).
Starts and repeated starts are otherwise functionally equivalent.

Data Valid: Data is valid, following the start condition, when EE_SDA is stable while EE_SCL is
high. Data can only be changed while the clock is low. There is one valid bit per clock pulse. Every
byte must be 8 bits long and is transmitted msb first.

Acknowledge: Each byte of data is followed by an acknowledge bit. The master generates a ninth
clock pulse for the acknowledge bit. The transmitter releases EE_SDA (high). The receiver drives
EE_SDA low so that it remains valid during the high period of the clock, taking into account the
setup and hold times. The receiver may be the master or the slave depending on the direction of
the data. Typically the receiver acknowledges each byte. If the master is the receiver, it does not
generate an acknowledge on the last byte of a transfer. This informs the slave to not drive the next
byte of data so that the master may generate a stop or repeated start condition.
Revision 2.0 (02-14-13)
140
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Figure 10.2 displays the various bus states of a typical I2C cycle.
data
can
change
data
stable
data
can
change
data
can
change
data
can
change
data
stable
EE_SDA
S
Sr
P
EE_SCL
Start Condition
Data Valid
or Ack
Data Valid
or Ack
Re-Start
Condition
Stop Condition
Figure 10.2 I2C Cycle
I2C EEPROM Device Addressing
10.2.2.2
The I2C EEPROM is addressed for a read or write operation by first sending a control byte followed
by the address byte or bytes. The control byte is preceded by a start condition. The control byte and
address byte(s) are each acknowledged by the EEPROM slave. If the EEPROM slave fails to send an
acknowledge, then the sequence is aborted and the EPC_TIMEOUT bit of the EEPROM Command
Register (E2P_CMD) is set.
The control byte consists of a 4-bit control code, 3-bits of chip/block select and one direction bit. The
control code is 1010b. For single byte addressing EEPROMs, the chip/block select bits are used for
address bits 10, 9, and 8. For double byte addressing EEPROMs, the chip/block select bits are set
low. The direction bit is set low to indicate the address is being written.
Figure 10.3 illustrates typical I2C EEPROM addressing bit order for single and double byte addressing.
Control Byte
A
A
A
A A
A A A A A A A A
C
0 C
9 8
K 7 6 5 4 3 2 1 0 K
S 1 0 1 0 1
0
Chip / Block R/~W
Select Bits
Address High
Byte
Control Byte
Address Byte
A A A A A A A
S 1 0 1 0 0 0 0 0 C 1 1 1 1 1 1
K 5
Chip / Block
Select Bits
Single Byte Addressing
4
3
2
1
0
Address Low
Byte
A
A
A A
A A A A A A A A
C
C
9 8 K 7 6 5 4 3 2 1 0 K
R/~W
Double Byte Addressing
Figure 10.3 I2C EEPROM Addressing
10.2.2.3
I2C EEPROM Byte Read
Following the device addressing, a data byte may be read from the EEPROM by outputting a start
condition and control byte with a control code of 1010b, chip/block select bits as described in
Section 10.2.2.2, and the R/~W bit high. The EEPROM will respond with an acknowledge, followed by
8-bits of data. If the EEPROM slave fails to send an acknowledge, then the sequence is aborted and
the EPC_TIMEOUT bit in the EEPROM Command Register (E2P_CMD) is set. The I2C master then
sends a no-acknowledge, followed by a stop condition.
SMSC LAN9312
141
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Figure 10.4 illustrates typical I2C EEPROM byte read for single and double byte addressing.
Data Byte
Control Byte
Chip / Block
Select Bits
Data Byte
Control Byte
A
A
A
A A
D D D D D D D D A
C S 1 0 1 0 1
1 C
P
9 8
7 6 5 4 3 2 1 0 C
K
0
K
K
A
A
D D D D D D D D A
C S 1 0 1 0 0 0 0 1 C
P
7 6 5 4 3 2 1 0 C
K
K
K
R/~W
Chip / Block R/~W
Select Bits
Single Byte Addressing Read
Double Byte Addressing Read
Figure 10.4 I2C EEPROM Byte Read
For a register level description of a read operation, refer to Section 10.2.1, "EEPROM Controller
Operation," on page 138.
10.2.2.4
I2C EEPROM Sequential Byte Reads
Following the device addressing, data bytes may be read sequentially from the EEPROM by outputting
a start condition and control byte with a control code of 1010b, chip/block select bits as described in
Section 10.2.2.2, and the R/~W bit high. The EEPROM will respond with an acknowledge, followed by
8-bits of data. If the EEPROM slave fails to send an acknowledge, then the sequence is aborted and
the EPC_TIMEOUT bit in the EEPROM Command Register (E2P_CMD) is set. The I2C master then
sends an acknowledge, and the EEPROM responds with the next 8-bits of data. This continues until
the last desired byte is read, at which point the I2C master sends a no-acknowledge, followed by a
stop condition.
Figure 10.4 illustrates typical I 2 C EEPROM sequential byte reads for single and double byte
addressing.
Data Byte
Control Byte
Data Byte
A
A
A
A
A
A A
D D D D D D D D
D D D D D D D D
C S 1 0 1 0 1
C
C
1 C
9
8
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
K
K
K
K
0
Chip / Block
Select Bits
...
Data Byte
D D D D D D D D A
P
7 6 5 4 3 2 1 0 C
K
R/~W
Single Byte Addressing Sequential Reads
Data Byte
Control Byte
Data Byte
A
A
A
A
D D D D D D D D
D D D D D D D D
C S 1 0 1 0 0 0 0 1 C
C
C
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
K
K
K
K
Chip / Block
Select Bits
...
Data Byte
D D D D D D D D A
P
7 6 5 4 3 2 1 0 C
K
R/~W
Double Byte Addressing Sequential Reads
Figure 10.5 I2C EEPROM Sequential Byte Reads
Sequential reads are used by the EEPROM Loader. Refer to Section 10.2.4, "EEPROM Loader" for
additional information.
For a register level description of a read operation, refer to Section 10.2.1, "EEPROM Controller
Operation," on page 138.
Revision 2.0 (02-14-13)
142
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
10.2.2.5
I2C EEPROM Byte Writes
Following the device addressing, a data byte may be written to the EEPROM by outputting the data
after receiving the acknowledge from the EEPROM. The data byte is acknowledged by the EEPROM
slave and the I2C master finishes the write cycle with a stop condition. If the EEPROM slave fails to
send an acknowledge, then the sequence is aborted and the EPC_TIMEOUT bit in the EEPROM
Command Register (E2P_CMD) is set.
Following the data byte write cycle, the I2C master will poll the EEPROM to determine when the byte
write is finished. A start condition is sent followed by a control byte with a control code of 1010b,
chip/block select bits low, and the R/~W bit low. If the EEPROM is finished with the byte write, it will
respond with an acknowledge. Otherwise, it will respond with a no-acknowledge and the I2C master
will repeat the poll. If the acknowledge does not occur within 30mS, a time-out occurs. Once the I2C
master receives the acknowledge, it concludes by sending a start condition, followed by a stop
condition, which will place the EEPROM into standby.
Figure 10.4 illustrates typical I2C EEPROM byte write.
Conclude
Data Cycle
Data Byte
Poll Cycle
Poll Cycle
Poll Cycle
Control Byte
Control Byte
Control Byte
A
A
A
A
D D D D D D D D
C
C P S 1 0 1 0 0 0 0 0 C S 1 0 1 0 0 0 0 0 C
K 7 6 5 4 3 2 1 0 K
K
K
Chip / Block R/~W
Select Bits
...
Chip / Block R/~W
Select Bits
A
S 1 0 1 0 0 0 0 0 C S P
K
Chip / Block
Select Bits
R/~W
Figure 10.6 I2C EEPROM Byte Write
For a register level description of a write operation, refer to Section 10.2.1, "EEPROM Controller
Operation," on page 138.
SMSC LAN9312
143
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
10.2.3
Microwire EEPROM
Based on the configuration strap eeprom_type_strap, various sized Microwire EEPROMs are
supported. The varying size ranges are supported by additional bits in the address field
(EPC_ADDRESS) of the EEPROM Command Register (E2P_CMD). Within each size range, the
largest EEPROM uses all the address bits, while the smaller EEPROMs treat the upper address bits
as don’t cares. The EEPROM controller drives all the address bits as requested regardless of the
actual size of the EEPROM. The supported size ranges for Microwire operation are shown in
Table 10.3.
Table 10.3 Microwire EEPROM Size Ranges
eeprom_size_strap[1:0]
# OF ADDRESS BITS
EEPROM SIZE
EEPROM TYPES
00
7
128 x 8
93xx46A
01
9
256 x 8 and 512 x 8
93xx56A, 93xx66A
10
11
1024 x 8 and 2048 x 8
93xx76A, 93xx86A
11
RESERVED
Refer to Section 15.5.10, "Microwire Timing," on page 453 for detailed Microwire timing information.
10.2.3.1
Microwire Master Commands
Table 10.4, Table 10.5, and Table 10.6 detail the Microwire command set, including the number of clock
cycles required, for 7, 9, and 11 address bits respectively. These commands are detailed in the
following sections as well as in Section 14.2.4.1, "EEPROM Command Register (E2P_CMD)," on
page 197.
Table 10.4 Microwire Command Set for 7 Address Bits
INST
START
BIT
OPCODE
ADDRESS
DATA TO
EEPROM
DATA FROM
EEPROM
# OF
CLOCKS
ERASE
1
11
A6 A5 A4 A3 A2 A1 A0
-
(RDY/~BSY)
10
ERAL
1
00
1 0 X X X X X
-
(RDY/~BSY)
10
EWDS
1
00
0 0 X X X X X
-
Hi-Z
10
EWEN
1
00
1 1 X X X X X
-
Hi-Z
10
READ
1
10
A6 A5 A4 A3 A2 A1 A0
-
D7 - D0
18
WRITE
1
01
A6 A5 A4 A3 A2 A1 A0
D7 - D0
(RDY/~BSY)
18
WRAL
1
00
0 1 X X X X X
D7 - D0
(RDY/~BSY)
18
Table 10.5 Microwire Command Set for 9 Address Bits
INST
START
BIT
OPCODE
ADDRESS
DATA TO
EEPROM
DATA FROM
EEPROM
# OF
CLOCKS
ERASE
1
11
A8 A7 A6 A5 A4 A3 A2 A1 A0
-
(RDY/~BSY)
12
ERAL
1
00
1 0 X X X X X X X
-
(RDY/~BSY)
12
Revision 2.0 (02-14-13)
144
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 10.5 Microwire Command Set for 9 Address Bits (continued)
INST
START
BIT
OPCODE
ADDRESS
DATA TO
EEPROM
DATA FROM
EEPROM
# OF
CLOCKS
EWDS
1
00
0 0 X X X X X X X
-
Hi-Z
12
EWEN
1
00
1 1 X X X X X X X
-
Hi-Z
12
READ
1
10
A8 A7 A6 A5 A4 A3 A2 A1 A0
-
D7 - D0
20
WRITE
1
01
A8 A7 A6 A5 A4 A3 A2 A1 A0
D7 - D0
(RDY/~BSY)
20
WRAL
1
00
0 1 X X X X X X X
D7 - D0
(RDY/~BSY)
20
Table 10.6 Microwire Command Set for 11 Address Bits
INST
START
BIT
OPCODE
ADDRESS
DATA TO
EEPROM
DATA FROM
EEPROM
# OF
CLOCKS
ERASE
1
11
A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
-
(RDY/~BSY)
14
ERAL
1
00
1 0 X X X X X X X X X
-
(RDY/~BSY)
14
EWDS
1
00
0 0 X X X X X X X X X
-
Hi-Z
14
EWEN
1
00
1 1 X X X X X X X X X
-
Hi-Z
14
READ
1
10
A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
-
D7 - D0
22
WRITE
1
01
A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
D7 - D0
(RDY/~BSY)
22
WRAL
1
00
0 1 X X X X X X X X X
D7 - D0
(RDY/~BSY)
22
10.2.3.2
ERASE (Erase Location)
If erase/write operations are enabled in the EEPROM, this command will erase the location selected
by the EPC_ADDRESS field of the EEPROM Command Register (E2P_CMD). The EPC_TIMEOUT
bit is set if the EEPROM does not respond within 30mS.
EECS
EECLK
EEDO
1
1
1
Ax
A0
EEDI
Figure 10.7 EEPROM ERASE Cycle
SMSC LAN9312
145
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
10.2.3.3
ERAL (Erase All)
If erase/write operations are enabled in the EEPROM, this command will initiate a bulk erase of the
entire EEPROM. The EPC_TIMEOUT bit of the EEPROM Command Register (E2P_CMD) is set if the
EEPROM does not respond within 30mS.
EECS
EECLK
EEDO
1
0
0
1
0
EEDI
Figure 10.8 EEPROM ERAL Cycle
10.2.3.4
EWDS (Erase/Write Disable)
After this command is issued, the EEPROM will ignore erase and write commands. To re-enable
erase/write operations, the EWEN command must be issued.
EECS
EECLK
EEDO
1
0
0
0
0
EEDI
Figure 10.9 EEPROM EWDS Cycle
Revision 2.0 (02-14-13)
146
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
10.2.3.5
EWEN (Erase/Write Enable)
This command enables the EEPROM for erase and write operations. The EEPROM will allow erase
and write operations until the EWDS command is sent, or until power is cycled.
Note: The EEPROM will power-up in the erase/write disabled state. Any erase or write operations
will fail until an EWEN command is issued.
EECS
EECLK
EEDO
1
0
0
1
1
EEDI
Figure 10.10 EEPROM EWEN Cycle
10.2.3.6
READ (Read Location)
This command will cause a read of the EEPROM location pointed to by the EPC_ADDRESS field of
the EEPROM Command Register (E2P_CMD). The result of the read is available in the EEPROM Data
Register (E2P_DATA).
EECS
EECLK
EEDO
1
1
0
Ax
A0
EEDI
D7
D0
Figure 10.11 EEPROM READ Cycle
SMSC LAN9312
147
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
10.2.3.7
WRITE (Write Location)
If erase/write operations are enabled in the EEPROM, this command will cause the contents of the
EEPROM Data Register (E2P_DATA) to be written to the EEPROM location pointed to by the
EPC_ADDRESS field of the EEPROM Command Register (E2P_CMD). The EPC_TIMEOUT bit of the
EEPROM Command Register (E2P_CMD) is set if the EEPROM does not respond within 30mS.
EECS
EECLK
EEDO
1
0
1
Ax
A0
D7
D0
EEDI
Figure 10.12 EEPROM WRITE Cycle
10.2.3.8
WRAL (Write All)
If erase/write operations are enabled in the EEPROM, this command will cause the contents of the
EEPROM Data Register (E2P_DATA) to be written to every EEPROM memory location. The
EPC_TIMEOUT bit of the EEPROM Command Register (E2P_CMD) is set if the EEPROM does not
respond within 30mS.
EECS
EECLK
EEDO
1
0
0
0
D7
1
D0
EEDI
Figure 10.13 EEPROM WRAL Cycle
Revision 2.0 (02-14-13)
148
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
10.2.4
EEPROM Loader
The EEPROM Loader interfaces to the I2C/Microwire EEPROM controller, the PHYs, and to the system
CSRs (via the Register Access MUX). Only system CSRs at addresses 100h and above are accessible
to the EEPROM Loader (with the addition of the PHY Management Interface Data Register
(PMI_DATA) and PHY Management Interface Access Register (PMI_ACCESS) at addresses A4 and
A8 respectively).
The EEPROM Loader runs upon a pin reset (nRST), power-on reset (POR), digital reset
(DIGITAL_RST bit in the Reset Control Register (RESET_CTL)), or upon the issuance of a RELOAD
command via the EEPROM Command Register (E2P_CMD). A soft reset will run the EEPROM
Loader, but only the MAC address is loaded into the Host MAC. Refer to Section 4.2, "Resets," on
page 36 for additional information on the LAN9312 resets.
The EEPROM contents must be loaded in a specific format for use with the EEPROM Loader. An
overview of the EEPROM content format is shown in Table 10.7. Each section of EEPROM contents
is discussed in detail in the following sections.
Table 10.7 EEPROM Contents Format Overview
EEPROM ADDRESS
0
VALUE
EEPROM Valid Flag
A5h
1
MAC Address Low Word [7:0]
1st
2
MAC Address Low Word [15:8]
2nd Byte on the Network
3
MAC Address Low Word [23:16]
3rd Byte on the Network
4
MAC Address Low Word [31:24]
4th Byte on the Network
5
MAC Address High Word [7:0]
5th Byte on the Network
6
MAC Address High Word [15:8]
6th Byte on the Network
7
Configuration Strap Values Valid Flag
Byte on the Network
A5h
8 - 11
Configuration Strap Values
See Table 10.8
12
Burst Sequence Valid Flag
A5h
13
Number of Bursts
See Section 10.2.4.5,
"Register Data"
Burst Data
See Section 10.2.4.5,
"Register Data"
14 and above
10.2.4.1
DESCRIPTION
EEPROM Loader Operation
Upon a pin reset (nRST), power-on reset (POR), digital reset (DIGITAL_RST bit in the Reset Control
Register (RESET_CTL)), or upon the issuance of a RELOAD command via the EEPROM Command
Register (E2P_CMD), the EPC_BUSY bit in the EEPROM Command Register (E2P_CMD) will be set.
While the EEPROM Loader is active, the READY bit of the Hardware Configuration Register
(HW_CFG) and Power Management Control Register (PMT_CTRL) is cleared and no writes to the
LAN9312 should be attempted. The operational flow of the EEPROM Loader can be seen in
Figure 10.14.
SMSC LAN9312
149
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
DIGITAL_RST, nRST,
POR, RELOAD
EPC_BUSY = 1
Read Byte 0
Byte 0 = A5h
N
Load PHY registers with
current straps
Y
Read Bytes 1-6
EPC_BUSY = 0
Write Bytes 1-6 into Host
MAC and switch MAC
Address Registers
Soft Reset
N
Read Byte 7-11
Y
EPC_BUSY = 1
Byte 7 = A5h
N
Load PHY registers with
current straps
Read Byte 0
Y
Byte 0 = A5h
Write Bytes 8-11 into
Configuration Strap
registers
N
Y
Read Bytes 1-6
Write Bytes 1-6 into Host
MAC Address Registers
Update PHY registers
Update VPHY registers
Update LED_CFG,
MANUAL_FC_1,
MANUAL_FC_2 and
MANUAL_FC_mii
registers
Read Byte 12
Byte 12 = A5h
N
Y
Perform register data
load loop
Figure 10.14 EEPROM Loader Flow Diagram
Revision 2.0 (02-14-13)
150
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
10.2.4.2
EEPROM Valid Flag
Following the release of nRST, POR, DIGITAL_RST, or a RELOAD command, the EEPROM Loader
starts by reading the first byte of data from the EEPROM. If the value of A5h is not read from the first
byte, the EEPROM Loader will load the current configuration strap values into the PHY registers (see
Section 10.2.4.4.1) and then terminate, clearing the EPC_BUSY bit in the EEPROM Command
Register (E2P_CMD). Otherwise, the EEPROM Loader will continue reading sequential bytes from the
EEPROM.
10.2.4.3
MAC Address
The next six bytes in the EEPROM, after the EEPROM Valid Flag, are written into the Host MAC
Address High Register (HMAC_ADDRH) and Host MAC Address Low Register (HMAC_ADDRL), and
the Switch Fabric MAC Address High Register (SWITCH_MAC_ADDRH) and Switch Fabric MAC
Address Low Register (SWITCH_MAC_ADDRL). The EEPROM bytes are written into the MAC
address registers in the order specified in Table 10.7. Refer to Section 9.6, "Host MAC Address," on
page 119 for additional information on MAC address loading.
10.2.4.3.1
HOST MAC ADDRESS RELOAD
While the EEPROM Loader is in the wait state, if a Host MAC reset is detected (via the Soft Reset bit
in the Hardware Configuration Register (HW_CFG)), the EEPROM Loader will read byte 0. If the byte
0 value is A5h, the EEPROM Loader will read bytes 1 through 6 from the EEPROM and reload the
Host MAC Address High Register (HMAC_ADDRH) and Host MAC Address Low Register
(HMAC_ADDRL). During this time, the EPC_BUSY bit in the EEPROM Command Register
(E2P_CMD) is set.
Note: The switch MAC address registers are not reloaded due to this condition.
10.2.4.4
Soft-Straps
The 7th byte of data to be read from the EEPROM is the Configuration Strap Values Valid Flag. If this
byte has a value of A5h, the next 4 bytes of data (8-11) are written into the configuration strap registers
per the assignments detailed in Table 10.8. If the flag byte is not A5h, these next 4 bytes are skipped
(they are still read to maintain the data burst, but are discarded). However, the current configuration
strap values are still loaded into the PHY registers (see Section 10.2.4.4.1). Refer to Section 4.2.4,
"Configuration Straps," on page 40 for more information on the LAN9312 configuration straps.
Table 10.8 EEPROM Configuration Bits
BYTE/BIT
7
6
5
4
3
2
1
0
Byte 8
BP_EN_
strap_1
FD_FC_
strap_1
manual_
FC_strap_1
manual_mdix
_strap_1
auto_mdix_
strap_1
speed_
strap_1
duplex_
strap_1
autoneg_
strap_1
Byte 9
BP_EN_
strap_2
FD_FC_
strap_2
manual_
FC_strap_2
manual_mdix
_strap_2
auto_mdix_
strap_2
speed_
strap_2
duplex_
strap_2
autoneg_
strap_2
BP_EN_
strap_mii
FD_FC_
strap_mii
manual_FC
_strap_mii
speed_
strap_mii
duplex_pol_
strap_mii
SQE_test_
disable_strap
_mii
Byte 10
LED_fun_strap[1:0]
Byte 11
LED_en_strap[7:0]
10.2.4.4.1
PHY REGISTERS SYNCHRONIZATION
Some PHY register defaults are based on configuration straps. In order to maintain consistency
between the updated configuration strap registers and the PHY registers, the Port x PHY AutoNegotiation Advertisement Register (PHY_AN_ADV_x), Port x PHY Special Modes Register
(PHY_SPECIAL_MODES_x), and Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x) are
written when the EEPROM Loader is run.
SMSC LAN9312
151
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
The Port x PHY Auto-Negotiation Advertisement Register (PHY_AN_ADV_x) is written with the new
defaults as detailed in Section 14.4.2.5, "Port x PHY Auto-Negotiation Advertisement Register
(PHY_AN_ADV_x)," on page 294.
The Port x PHY Special Modes Register (PHY_SPECIAL_MODES_x) is written with the new defaults
as detailed in Section 14.4.2.9, "Port x PHY Special Modes Register (PHY_SPECIAL_MODES_x)," on
page 301.
The Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x) is written with the new defaults
as detailed in Section 14.4.2.1, "Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x)," on
page 288. Additionally, the Restart Auto-negotiation bit is set in this register. This re-runs the Autonegotiation using the new default values of the Port x PHY Auto-Negotiation Advertisement Register
(PHY_AN_ADV_x) register to determine the new Auto-negotiation results.
Note: Each of these PHY registers is written in its entirety, overwriting any previously changed bits.
10.2.4.4.2
VIRTUAL PHY REGISTERS SYNCHRONIZATION
Some PHY register defaults are based on configuration straps. In order to maintain consistency
between the updated configuration strap registers and the Virtual PHY registers, the Virtual PHY AutoNegotiation Advertisement Register (VPHY_AN_ADV), Virtual PHY Special Control/Status Register
( V P H Y _ S P E C I A L _ C O N T R O L _ S TAT U S ) , a n d V i r t u a l P H Y B a s i c C o n t r o l R e g i s t e r
(VPHY_BASIC_CTRL) are written when the EEPROM Loader is run.
The Virtual PHY Auto-Negotiation Advertisement Register (VPHY_AN_ADV) is written with the new
defaults as detailed in Section 14.2.8.5, "Virtual PHY Auto-Negotiation Advertisement Register
(VPHY_AN_ADV)," on page 252.
The Virtual PHY Special Control/Status Register (VPHY_SPECIAL_CONTROL_STATUS) is written
with the new defaults as detailed in Section 14.2.8.8, "Virtual PHY Special Control/Status Register
(VPHY_SPECIAL_CONTROL_STATUS)," on page 257.
The Virtual PHY Basic Control Register (VPHY_BASIC_CTRL) is written with the new defaults as
detailed in Section 14.2.8.1, "Virtual PHY Basic Control Register (VPHY_BASIC_CTRL)," on page 246.
Additionally, the Restart Auto-negotiation bit is set in this register. This re-runs the Auto-negotiation
using the new default values of the Virtual PHY Auto-Negotiation Advertisement Register
(VPHY_AN_ADV) register to determine the new Auto-negotiation results.
Note: Each of these VPHY registers is written in its entirety, overwriting any previously changed bits.
10.2.4.4.3
LED AND MANUAL FLOW CONTROL REGISTER SYNCHRONIZATION
Since the defaults of the LED Configuration Register (LED_CFG), Port 1 Manual Flow Control Register
(MANUAL_FC_1), Port 2 Manual Flow Control Register (MANUAL_FC_2), and Port 0(Host MAC)
Manual Flow Control Register (MANUAL_FC_MII) are based on configuration straps, the EEPROM
Loader reloads these registers with their new default values.
10.2.4.5
Register Data
Optionally following the configuration strap values, the EEPROM data may be formatted to allow
access to the LAN9312 parallel, directly writable registers. Access to indirectly accessible registers
(e.g. Switch Engine registers, etc.) is achievable with an appropriate sequence of writes (at the cost
of EEPROM space).
This data is first preceded with a Burst Sequence Valid Flag (EEPROM byte 12). If this byte has a
value of A5h, the data that follows is recognized as a sequence of bursts. Otherwise, the EEPROM
Loader is finished, will go into a wait state, and clear the EPC_BUSY bit in the EEPROM Command
Register (E2P_CMD). This can optionally generate an interrupt.
The data at EEPROM byte 13 and above should be formatted in a sequence of bursts. The first byte
is the total number of bursts. Following this is a series of bursts, each consisting of a starting address,
count, and the count x 4 bytes of data. This results in the following formula for formatting register data:
Revision 2.0 (02-14-13)
152
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
8-bits number_of_bursts
repeat (number_of_bursts)
16-bits {starting_address[9:2] / count[7:0]}
repeat (count)
8-bits data[31:24], 8-bits data[23:16], 8-bits data[15:8], 8-bits data[7:0]
Note: The starting address is a DWORD address. Appending two 0 bits will form the register address.
As an example, the following is a 3 burst sequence, with 1, 2, and 3 DWORDs starting at register
addresses 40h, 80h, and C0h respectively:
A5h, (Burst Sequence Valid Flag)
3h, (number_of_bursts)
16{10h, 1h}, (starting_address1 divided by 4 / count1)
11h, 12h, 13h, 14h, (4 x count1 of data)
16{20h, 2h}, (starting_address2 divided by 4 / count2)
21h, 22h, 23h, 24h, 25h, 26h, 27h, 28h, (4 x count2 of data)
16{30h, 3h}, (starting_address3 divided by 4 / count3)
31h, 32h, 33h, 34h, 35h, 36h, 37h, 38h, 39h, 3Ah, 3Bh, 3Ch (4 x count3 of data)
In order to avoid overwriting the Switch CSR register interface or the PHY Management Interface
(PMI), the EEPROM Loader waits until the CSR Busy bit of the Switch Fabric CSR Interface Command
Register (SWITCH_CSR_CMD) and the MII Busy bit of the PHY Management Interface Access
Register (PMI_ACCESS) are cleared before performing any register write.
The EEPROM Loader checks that the EEPROM address space is not exceeded. If so, it will stop and
set the EEPROM Loader Address Overflow bit in the EEPROM Command Register (E2P_CMD). The
address limit is based on the eeprom_size_strap which specifies a range of sizes. The address limit
is set to the largest value of the specified range.
10.2.4.6
EEPROM Loader Finished Wait-State
Once finished with the last burst, the EEPROM Loader will go into a wait-state and the EPC_BUSY
bit of the EEPROM Command Register (E2P_CMD) will be cleared.
10.2.4.7
Reset Sequence and EEPROM Loader
In order to allow the EEPROM Loader to change the Port 1/2 PHYs and Virtual PHY strap inputs and
maintain consistency with the PHY and Virtual PHY registers, the following sequence is used:
1. After power-up or upon a hardware reset (nRST), the straps are sampled into the LAN9312 as
specified in Section 15.5.2, "Reset and Configuration Strap Timing," on page 445.
2. After the PLL is stable, the main chip reset is released and the EEPROM Loader reads the
EEPROM and configures (overrides) the strap inputs.
3. The EEPROM Loader writes select Port 1/2 and Virtual PHY registers, as specified in
Section 10.2.4.4.1 and Section 10.2.4.4.2, respectively.
Note: Step 3 is also performed in the case of a RELOAD command or digital reset.
SMSC LAN9312
153
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 11 IEEE 1588 Hardware Time Stamp Unit
11.1
Functional Overview
The LAN9312 provides hardware support for the IEEE 1588 Precision Time Protocol (PTP), allowing
clock synchronization with remote Ethernet devices, packet time stamping, and time driven event
generation. Time stamping is supported on all ports, with an individual IEEE 1588 Time Stamp module
connected to each port via the MII bus. Any port may function as a master or a slave clock per the
IEEE 1588 specification, and the LAN9312 as a whole may function as a boundary clock.
A 64-bit tunable clock is provided that is used as the time source for all IEEE 1588 time stamp related
functions. An IEEE 1588 Clock/Events block provides IEEE 1588 clock comparison based interrupt
generation and time stamp related GPIO event generation. Two LAN9312 GPIO pins (GPIO[8:9]) can
be used to trigger a time stamp capture when configured as an input, or output a signal from the GPIO
based on an IEEE 1588 clock target compare event when configured as an output. Section 11.1.2,
"Block Diagram" describes the various IEEE 1588 related blocks and how they interface to other
LAN9312 functions.
All features of the IEEE 1588 hardware time stamp unit can be monitored and configured via their
respective configuration and status registers. A detailed description of all IEEE 1588 CSRs is included
in Section 14.2.5, "IEEE 1588," on page 201.
11.1.1
IEEE 1588
IEEE 1588 specifies a Precision Time Protocol (PTP) used by master and slave clock devices to pass
time information in order to achieve clock synchronization. Five network message types are defined:

Sync

Delay_Req

Follow_Up

Delay_Resp

Management
Only the first four message types (Sync, Delay_Req, Follow_Up, Delay_Resp) are used for clock
synchronization. Using these messages, the protocol software may calculate the offset and network
delay between time stamps, adjusting the slave clock frequency as needed. Refer to the IEEE 1588
protocol for message definitions and proper usage.
A PTP domain is segmented into PTP sub-domains, which are then segmented into PTP
communication paths. Within each PTP communication path there is a maximum of one master clock,
which is the source of time for each slave clock. The determination of which clock is the master and
which clock(s) is(are) the slave(s) is not fixed, but determined by the IEEE 1588 protocol. Similarly,
each PTP sub-domain may have only one master clock, referred to as the Grand Master Clock.
PTP communication paths are conceptually equivalent to Ethernet collision domains and may contain
devices which extend the network. However, unlike Ethernet collision domains, the PTP
communication path does not stop at a network switch, bridge, or router. This leads to a loss of
precision when the network switch/bridge/router introduces a variable delay. Boundary clocks are
defined which conceptually bypass the switch/bridge/router (either physically or via device integration).
Essentially, a boundary clock acts as a slave to an upstream master, and as a master to a down stream
slave. A boundary clock may contain multiple ports, but a maximum of one slave port is permitted.
For more information on the IEEE 1588 protocol, refer to the National Institute of Standards and
Technology IEEE 1588 website:
http://ieee1588.nist.gov/
Revision 2.0 (02-14-13)
154
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
11.1.2
Block Diagram
The LAN9312 IEEE 1588 implementation is illustrated in Figure 11.1, and consists of the following
major function blocks:

IEEE 1588 Time Stamp
These three identical blocks provide time stamping functions on all switch fabric ports.

IEEE 1588 Clock
This block provides a 64-bit tunable clock that is used as the time source for all IEEE 1588 time
stamp related functions.

IEEE 1588 Clock/Events
This block provides IEEE 1588 clock comparison-based interrupt generation and time stamp related
GPIO event generation.
IEEE 1588
Time Stamp
MII
Port 0
10/100
PHY
Port 1
Ethernet
IEEE 1588
Time Stamp
MII
To Host MAC
Switch Fabric
10/100
PHY
MII
Port 2
Ethernet
IEEE 1588 Time Stamp
RX
Sync / Delay_Req
Msg Detect RX
RX: Delay_Req for Master, Sync for Slave
TX
Sync / Delay_Req
Msg Detect TX
TX: Sync for Master, Delay_Req for Slave
IEEE 1588 Clock
Clock Capture RX
Src UUID Capture RX
Sequence ID Capture RX
IRQ Flag
Clock Capture TX
Src UUID Capture TX
Sequence ID Capture TX
IRQ Flag
32 Bit Addend
+
32 Bit Accumulator
inc
64 Bit Clock
carry
host
host
IEEE 1588 Clock Events
GPIO[8:9]
(Outputs)
GPIO[8:9]
(Inputs)
64 Bit Reload / Add
load / add
64 Bit Clock Target
compare >=
IRQ Flag
Clock Capture GPIO8
IRQ Flag
Clock Capture GPIO9
IRQ Flag
host
IRQ Flags
IRQ Enables
X9
To INT_STS register
Figure 11.1 IEEE 1588 Block Diagram
SMSC LAN9312
155
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
11.2
IEEE 1588 Time Stamp
The LAN9312 contains three identical IEEE 1588 Time Stamp blocks as shown in Figure 11.1. These
blocks are responsible for capturing the source UUID, sequence ID, and current 64-bit IEEE 1588 clock
time upon detection of a Sync or Delay_Req message type on their respective port. The mode of the
clock (master or slave) determines which message is detected on receive and transmit. For slave clock
operation, Sync messages are detected on receive and Delay_Req messages on transmit. For master
clock operation, Delay_Req messages are detected on receive and Sync messages on transmit.
Follow_Up, Delay_Resp and Management packet types do not cause capture. Each port may be
individually configured as an IEEE 1588 master or slave clock via the master/slave bits (M_nS_1 for
Port 1, MnS_2 for Port2, and M_nS_MII for Port 0) in the 1588 Configuration Register (1588_CONFIG).
Table 11.1 summarizes the message type detection under slave and master IEEE 1588 clock
operation.
Table 11.1 IEEE 1588 Message Type Detection
IEEE 1588 CLOCK MODE
RECEIVE
TRANSMIT
Slave
(M_nS_x = 0)
Sync
Delay_Req
Master
(M_nS_x = 1)
Delay_Req
Sync
For ports 1 and 2, receive is defined as data from the PHY (from the outside world) and transmit is
defined as data to the PHY. This is consistent with the point-of-view of where the partner clock resides
(LAN9312 receives packets from the partner via the PHY, etc.). For the time stamp module connected
to the Host MAC (Port 0), the definition of transmit and receive is reversed. Receive is defined as data
from the switch fabric, while transmit is defined as data to the switch fabric. This is consistent with the
point-of-view of where the partner clock resides (LAN9312 receives packets from the partner via the
switch fabric, etc.).
As defined by IEEE 1588, and shown in Figure 11.2, the message time stamp point is defined as the
leading edge of the first data bit following the Start of Frame Delimiter (SFD). However, since the
packet contents are not yet known, the time stamp can not yet be loaded into the capture register.
Therefore, the time stamp is first stored into a temporary internal holding register at the start of every
packet.
Message Timestamp
Point
Ethernet
Start of Frame
Delimiter
Preamble
Octet
1
0
1
0
1
0
1
0
First Octet
following
Start of Frame
1
0
1 1 1
0
0 0 0 0 0 0 0
bit time
Figure 11.2 IEEE 1588 Message Time Stamp Point
Revision 2.0 (02-14-13)
156
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Clock synchronization and hardware processing between the network data and the time stamp capture
hardware causes the time stamp point to be slightly delayed. The host software can account for this
delay, as it is fairly deterministic. Table 11.2 details the time stamp capture delay as a function of the
mode of operation. Refer to Chapter 7, "Ethernet PHYs," on page 82 for details on these modes.
Table 11.2 Time Stamp Capture Delay
MODE OF OPERATION
DELAY (+/- 10 nS)
100 Mbps
30 nS
10 Mbps
120 nS
Once the packet type is matched, according to Table 11.1, and the Frame Check Sequence (FCS) is
verified, the following occurs:

The time stamp is loaded into the corresponding ports’ capture registers:
–On Reception: Port x 1588 Clock High-DWORD Receive Capture Register
(1588_CLOCK_HI_RX_CAPTURE_x) and Port x 1588 Clock Low-DWORD Receive Capture
Register (1588_CLOCK_LO_RX_CAPTURE_x)
–On Transmission: Port x 1588 Clock High-DWORD Transmit Capture Register
(1588_CLOCK_HI_TX_CAPTURE_x) and Port x 1588 Clock Low-DWORD Transmit Capture
Register (1588_CLOCK_LO_TX_CAPTURE_x)

The Sequence ID and Source UUID are loaded into the corresponding ports’ registers:
–On Reception: Port x 1588 Sequence ID, Source UUID High-WORD Receive Capture Register
(1588_SEQ_ID_SRC_UUID_HI_RX_CAPTURE_x) and Port x 1588 Source UUID LowDWORD Receive Capture Register (1588_SRC_UUID_LO_RX_CAPTURE_x)
–On Transmission: Port x 1588 Sequence ID, Source UUID High-WORD Transmit Capture
Register (1588_SEQ_ID_SRC_UUID_HI_TX_CAPTURE_x) and Port x 1588 Source UUID
Low-DWORD Transmit Capture Register (1588_SRC_UUID_LO_TX_CAPTURE_x)

The corresponding maskable interrupt flag is set in the 1588 Interrupt Status and Enable Register
(1588_INT_STS_EN). (Refer to Section 11.6, "IEEE 1588 Interrupts," on page 160 for information
on IEEE 1588 interrupts.)
Note: Packets that do not contain an integral number of octets are not considered valid and do not
cause a capture.
11.2.1
Capture Locking
The corresponding ports’ clock capture, sequence ID, and source UUID registers can be optionally
locked when a capture event occurs, preventing them from being overwritten until the host clears the
corresponding interrupt flag in the 1588 Interrupt Status and Enable Register (1588_INT_STS_EN).
This is accomplished by setting the corresponding lock enable bit(s) in the 1588 Configuration Register
(1588_CONFIG). Each port has two lock enable control bits within this register, which allow the receive
and transmit portions of each port to be locked independently. In addition, a lock enable bit is provided
for each time stamp enabled GPIO (LOCK_ENABLE_GPIO_8 and LOCK_ENABLE_GPIO_9) which
prevents the corresponding GPIO clock capture registers from being overwritten when the GPIO
interrupt in 1588 Interrupt Status and Enable Register (1588_INT_STS_EN) is set. Refer to Section
14.2.5.22, "1588 Configuration Register (1588_CONFIG)," on page 222 for additional information on
the capture locking related bits.
SMSC LAN9312
157
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
11.2.2
PTP Message Detection
In order to provide the most flexibility, loose packet type matching is used by the LAN9312. This
assumes that for all packets received with a valid FCS, only the MAC destination address is required
to qualify them as a PTP message. For Ethernet, four multicast addresses are specified in the PTP
protocol: 224.0.1.129 through 224.0.1.132. These map to Ethernet MAC addresses 01:00:5e:00:01:81
through 01:00:5e:00:01:84. Each of these addresses has one enable bit per port in the 1588
Configuration Register (1588_CONFIG) which enables/disables the corresponding address as a PTP
address on the specified port.
In addition to the fixed addresses, a user defined (host programmable) PTP address may be input via
the 1588 Auxiliary MAC Address High-WORD Register (1588_AUX_MAC_HI) and 1588 Auxiliary MAC
Address Low-DWORD Register (1588_AUX_MAC_LO). The user defined address may be
disabled/enabled as a PTP address on each port via the dedicated enable bits in the 1588
Configuration Register (1588_CONFIG). A summary of the supported PTP multicast addresses and
corresponding enable bits can be seen in Table 11.3.
Table 11.3 PTP Multicast Addresses
CORRESPONDING
MAC ADDRESS
RELATED ENABLE BITS IN THE
1588_CONFIG REGISTER
224.0.1.129
(Primary)
01:00:5e:00:01:81
MAC_PRI_EN_1 (Port 1)
MAC_PRI_EN_2 (Port 2)
MAC_PRI_EN_MII (Port 0)
224.0.1.130
(Alternate 1)
01:00:5e:00:01:82
MAC_ALT1_EN_1 (Port 1)
MAC_ALT1_EN_2 (Port 2)
MAC_ALT1_EN_MII (Port 0)
224.0.1.131
(Alternate 2)
01:00:5e:00:01:83
MAC_ALT2_EN_1 (Port 1)
MAC_ALT2_EN_2 (Port 2)
MAC_ALT2_EN_MII (Port 0)
224.0.1.132
(Alternate 3)
01:00:5e:00:01:84
MAC_ALT3_EN_1 (Port 1)
MAC_ALT3_EN_2 (Port 2)
MAC_ALT3_EN_MII (Port 0)
User Defined
User Defined Address
(1588_AUX_MAC_HI &
1588_AUX_MAC_LO registers)
MAC_USER_EN_1 (Port 1)
MAC_USER_EN_2 (Port 2)
MAC_USER_EN_MII (Port 0)
PTP ADDRESS
Once a packet is determined to match a PTP destination address, it is further qualified as a Sync or
Delay_Req message type. On Ethernet, PTP uses UDP messages. Within the UDP payload is the PTP
control byte (offset 32 starting at 0). This byte determines the message type: 0x00 for a Sync message,
0x01 for a Delay_Req message. The UDP payload starts at packet byte offset 42 (from 0) for untagged
packets and at byte offset 46 for tagged packets.
Note: Both tagged and untagged packets are supported. Only Ethernet II packet encoding and IPv4
are supported.
Note: For proper routing of the PTP packets, the host must program an entry into the switch engine
Address Logic Resolution (ALR) Table. The MAC address should be one of the reserved
Multicast addresses in Table 11.3, with Port 0(Host MAC) as a destination.The Static and Valid
bits must also be set. Refer to Chapter 6, "Switch Fabric," on page 55 for more information.
Revision 2.0 (02-14-13)
158
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
11.3
IEEE 1588 Clock
The 64-bit IEEE 1588 clock is the time source for all IEEE 1588 related functions of the LAN9312. It
is readable and writable by the host via the 1588 Clock High-DWORD Register (1588_CLOCK_HI) and
1588 Clock Low-DWORD Register (1588_CLOCK_LO).
In order to accurately read this clock, a special procedure must be followed. Since two DWORD reads
are required to fully read the 64-bit clock, the possibility exists that as the lower 32-bits roll over, a
wrong intermediate value could be read. To prevent this, a snapshot register technique is used. When
the 1588_CLOCK_SNAPSHOT bit in the 1588 Command Register (1588_CMD) register is written with
“1”, the current value of the 1588 clock is saved, allowing it to be properly read.
When writing a new value to the IEEE 1588 clock, two 32-bit write cycles are required (one for each
clock register) before the registers are affected. The writes may be in any order. However, caution must
be observed when changing the clock value in a live environment as it will disrupt linear time. If the
clock must be adjusted during operation of the 1588 protocol, it is preferred to adjust the Addend value,
effectively speeding-up or slowing-down the clock until the correct time is achieved.
The 64-bit IEEE 1588 clock consists of the 32-bit 1588 Clock Addend Register
(1588_CLOCK_ADDEND) that is added to a 32-bit Accumulator every 100 MHz clock. Upon overflow
of the Accumulator, the 64- bit IEEE 1588 clock is incremented. The Addend / Accumulator pair form
a high precision frequency divider which can be used to compensate for the inaccuracy of the
reference crystal. The nominal frequency of the 64-bit IEEE 1588 clock and the value of the Addend
are calculated as follows:
FreqClock = (Addend / 232) * 100 MHz
Addend = (FreqClock * 232) / 100 MHz
Typical values for the Addend are shown in Table 11.4. These values should be adjusted based on the
accuracy of the IEEE 1588 clock compared to the master clock per the PTP protocol. The adjustment
precision column of the table shows the percentage change for the specified IEEE 1588 clock
frequency if the Addend was to be incremented or decremented by 1.
Table 11.4 Typical IEEE 1588 Clock Addend Values
11.4
IEEE 1588 CLOCK
(FreqClock)
1588_CLOCK_ADDEND
(Addend)
ADJUSTMENT PRECISION %
33 MHz
547AE147h
7.1*10-8
50 MHz
80000000h
4.7*10-8
66 MHz
A8F5C28Fh
3.5*10-8
75 MHz
C0000000h
3.1*10-8
90 MHz
E6666666h
2.6*10-8
IEEE 1588 Clock/Events
The IEEE 1588 Clock/Events block is responsible for generating and controlling all IEEE 1588 clock
related events. A 64-bit comparator is included in this block which compares the 64-bit IEEE 1588 clock
with a 64-bit Clock Target loaded in the 1588 Clock Target High-DWORD Register
( 1 5 8 8 _ C L O C K _ TA R G E T _ H I ) a n d 1 5 8 8 C l o c k Ta r g e t L o w - D W O R D R e g i s t e r
(1588_CLOCK_TARGET_LO).
SMSC LAN9312
159
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
When the IEEE 1588 clock equals the Clock Target, a clock event occurs which triggers the following:

The maskable interrupt 1588_TIMER_INT is set in the 1588 Interrupt Status and Enable Register
(1588_INT_STS_EN).

The RELOAD_ADD bit in the 1588 Configuration Register (1588_CONFIG) is checked to determine
the new Clock Target behavior:
–RELOAD_ADD = 1:
The new Clock Target is loaded from the 64-bit Reload / Add Registers (1588 Clock Target
Reload High-DWORD Register (1588_CLOCK_TARGET_RELOAD_HI) and 1588 Clock Target
Reload/Add Low-DWORD Register (1588_CLOCK_TARGET_RELOAD_LO)).
–RELOAD_ADD = 0:
The Clock Target is incremented by the 1588 Clock Target Reload/Add Low-DWORD Register
(1588_CLOCK_TARGET_RELOAD_LO).
Note: Writing the IEEE 1588 clock may cause the interrupt event to occur if the new IEEE 1588 clock
value is set equal to the current Clock Target.
The Clock Target reload function (RELOAD_ADD = 1) allows the host to pre-load the next trigger time.
The add function (RELOAD_ADD = 0), allows for a repeatable event. When the Clock Target overflows,
it will wrap around past 0, as will the 64-bit IEEE 1588 clock. Since the Clock Target and Reload / Add
Registers are 64-bits, they require two 32-bit write cycles, one to each half, before the registers are
affected. The writes may be in any order.
11.5
IEEE 1588 GPIOs
In addition to time stamping PTP packets, the IEEE 1588 clock value can be saved into a set of clock
capture registers based on the GPIO[9:8] inputs. When configured as outputs, GPIO[9:8] can be used
to output a signal based on an IEEE 1588 clock target compare event. Refer to Section 13.2.1, "GPIO
IEEE 1588 Timestamping," on page 163 for information on using GPIO[9:8] for IEEE 1588 time
stamping functions.
11.6
IEEE 1588 Interrupts
The IEEE 1588 hardware time stamp unit provides multiple interrupt conditions. These include time
stamp indication on the transmitter and receiver side of each port, individual GPIO[9:8] input time
stamp interrupts, and a clock comparison event interrupt. All IEEE 1588 interrupts are located in the
1588 Interrupt Status and Enable Register (1588_INT_STS_EN) and are fully maskable via their
respective enable bits. Refer to Section 14.2.5.23, "1588 Interrupt Status and Enable Register
(1588_INT_STS_EN)," on page 226 for bit-level definitions of all IEEE 1588 interrupts and enables.
All IEEE 1588 interrupts are ANDed with their individual enables and then ORed, as shown in
Figure 11.1, generating the 1588_EVNT bit of the Interrupt Status Register (INT_STS).
When configured as an input, GPIO[9:8] have the added functionality of clearing the Clock Target
interrupt bit (1588_TIMER_INT) of the 1588 Interrupt Status and Enable Register (1588_INT_STS_EN)
on an active edge. GPIO inputs must be active for greater than 40 nS to be recognized as clear events.
For more information on IEEE 1588 GPIO interrupts, refer to Section 13.2.2, "GPIO Interrupts," on
page 163.
Refer to Chapter 5, "System Interrupts," on page 49 for additional information on the LAN9312
interrupts.
Revision 2.0 (02-14-13)
160
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 12 General Purpose Timer & Free-Running Clock
This chapter details the LAN9312 General Purpose Timer (GPT) and the Free-Running Clock.
12.1
General Purpose Timer
The LAN9312 provides a 16-bit programmable General Purpose Timer that can be used to generate
periodic system interrupts. The resolution of this timer is 100uS.
The GPT loads the General Purpose Timer Count Register (GPT_CNT) with the value in the
GPT_LOAD field of the General Purpose Timer Configuration Register (GPT_CFG) when the
TIMER_EN bit of the General Purpose Timer Configuration Register (GPT_CFG) is asserted (1). On
a chip-level reset, or when the TIMER_EN bit changes from asserted (1) to de-asserted (0), the
GPT_LOAD field is initialized to FFFFh. The General Purpose Timer Count Register (GPT_CNT) is
also initialized to FFFFh on reset. Software can write a pre-load value into the GPT_LOAD field at any
time (e.g. before or after the TIMER_EN bit is asserted).
Once enabled, the GPT counts down until it reaches 0000h, or until a new pre-load value is written to
the GPT_LOAD field. At 0000h, the counter wraps around to FFFFh, asserts the GPT interrupt status
bit (GPT_INT) in the Interrupt Status Register (INT_STS), asserts the IRQ interrupt (if GPT_INT_EN
is set in the Interrupt Status Register (INT_STS)), and continues counting. GPT_INT is a sticky bit.
Once this bit is asserted, it can only be cleared by writing a 1 to the bit. Refer to Section 5.2.7, "General
Purpose Timer Interrupt," on page 53 for additional information on the GPT interrupt.
12.2
Free-Running Clock
The Free-Running Clock (FRC) is a simple 32-bit up-counter that operates from a fixed 25MHz clock.
The current FRC value can be read via the Free Running 25MHz Counter Register (FREE_RUN). On
assertion of a chip-level reset, this counter is cleared to zero. On de-assertion of a reset, the counter
is incremented once for every 25MHz clock cycle. When the maximum count has been reached, the
counter rolls over to zeros. The FRC does not generate interrupts.
Note: The free running counter can take up to 160nS to clear after a reset event.
SMSC LAN9312
161
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 13 GPIO/LED Controller
13.1
Functional Overview
The GPIO/LED Controller provides 12 configurable general purpose input/output pins, GPIO[11:0].
These pins can be individually configured to function as inputs, push-pull outputs, or open drain outputs
and each is capable of interrupt generation with configurable polarity. Two of the GPIO pins (GPIO[9:8])
can be used for IEEE 1588 timestamp functions, allowing GPIO driven 1588 time clock capture when
configured as an input, or GPIO output generation based on an IEEE 1588 clock target compare event.
In addition, 8 of the GPIO pins can be alternatively configured as LED outputs. These pins, GPIO[7:0]
(nP1LED[3:0] and nP2LED[3:0]), may be enabled to drive Ethernet status LEDs for external indication
of various attributes of the switch ports.
GPIO and LED functionality is configured via the GPIO/LED System Control and Status Registers
(CSRs), accessible through the Host Bus Interface (HBI). These registers are defined in Section
14.2.3, "GPIO/LED," on page 192.
13.2
GPIO Operation
The GPIO controller is comprised of 12 programmable input/output pins. These pins are individually
configurable via the GPIO CSRs. On application of a chip-level reset:

All GPIOs are set as inputs (GPDIR[11:0] cleared in General Purpose I/O Data & Direction Register
(GPIO_DATA_DIR))

All GPIO interrupts are disabled (GPIO[11:0]_INT_EN cleared in General Purpose I/O Interrupt
Status and Enable Register (GPIO_INT_STS_EN)

All GPIO interrupts are configured to low logic level triggering (GPIO_INT_POL[11:0] cleared in
General Purpose I/O Configuration Register (GPIO_CFG))
Note: GPIO[7:0] may be configured as LED outputs by default, dependant on the LED_en_stap[7:0]
configuration straps. Refer to Section 13.3, "LED Operation" for additional information.
The direction and buffer type of all 12 GPIOs are configured via the General Purpose I/O Configuration
Register (GPIO_CFG) and General Purpose I/O Data & Direction Register (GPIO_DATA_DIR). The
direction of each GPIO, input or output, should be configured first via its respective GPIO direction bit
(GPDIR[11:0]) in the General Purpose I/O Data & Direction Register (GPIO_DATA_DIR). When
configured as an output, the output buffer type for each GPIO is selected by the GPIOBUF[11:0] bits
in the General Purpose I/O Configuration Register (GPIO_CFG). Push/pull and open-drain output
buffers are supported for each GPIO. When functioning as an open-drain driver, the GPIO output pin
is driven low when the corresponding data register bit (GPIOD in the General Purpose I/O Data &
Direction Register (GPIO_DATA_DIR)) is cleared to 0, and is not driven when set to 1.
When a GPIO is enabled as an output, the value output to the GPIO pin is set via the corresponding
GPIOD[11:0] bit in the General Purpose I/O Data & Direction Register (GPIO_DATA_DIR). For GPIOs
configured as inputs, the corresponding GPIOD[11:0] bit reflects the current state of the GPIO input.
Note: For GPIO[9:8], the pin direction is a function of both the GPDIR[9:8] bits of the General
Purpose I/O Data & Direction Register (GPIO_DATA_DIR) and the 1588_GPIO_OE[9:8] bits in
the General Purpose I/O Configuration Register (GPIO_CFG).
Revision 2.0 (02-14-13)
162
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
13.2.1
GPIO IEEE 1588 Timestamping
Two of the GPIO pins, GPIO[9:8], have the option to be used for IEEE 1588 time stamp functions. This
allows a time stamp capture to be triggered when the GPIO is configured as an input, or output a signal
from the GPIO based on an IEEE 1588 clock target compare event when configured as an output.
Refer to Chapter 11, "IEEE 1588 Hardware Time Stamp Unit," on page 154 for additional information
on the IEEE 1588 time stamping functions of the LAN9312.
13.2.1.1
IEEE 1588 GPIO Inputs
When the GPIO[9:8] pins are configured as inputs, an active edge will capture the IEEE 1588 clock
into the high and low 1588 capture registers (1588_CLOCK_HI_CAPTURE_GPIO_x, and
1588_CLOCK_LO_CAPTURE_GPIO_x where “x” represents the number of the respective 1588
enabled GPIO) and set the corresponding interrupt flags GPIO[9:8]_INT and 1588_GPIO[9:8]_INT in
the General Purpose I/O Interrupt Status and Enable Register (GPIO_INT_STS_EN) and 1588
Interrupt Status and Enable Register (1588_INT_STS_EN) respectively. The GPIO[9:8] inputs can also
be configured to clear the Clock Target interrupt (1588_TIMER_INT) in the 1588 Interrupt Status and
Enable
Register
(1588_INT_STS_EN)
by
setting
the
corresponding
GPIO_1588_TIMER_INT_CLEAR_EN[9:8] bit in the General Purpose I/O Configuration Register
(GPIO_CFG). GPIO inputs must be active for greater than 40nS to be recognized as capture or
interrupt clear events.
13.2.1.2
IEEE 1588 GPIO Outputs
The GPIO[9:8] pins can be configured as IEEE 1588 enabled outputs by setting the corresponding
1588_GPIO_OE[9:8] bits in the General Purpose I/O Configuration Register (GPIO_CFG). These bits
override the GPDIR[9:8] bits of the General Purpose I/O Data & Direction Register (GPIO_DATA_DIR)
and allow for GPIO output generation based on the IEEE 1588 clock target compare event. Clock
target compare events occur when the value loaded into the 1588 Clock Target High-DWORD Register
( 1 5 8 8 _ C L O C K _ TA R G E T _ H I ) a n d 1 5 8 8 C l o c k Ta r g e t L o w - D W O R D R e g i s t e r
(1588_CLOCK_TARGET_LO) matches the current IEEE 1588 clock value in the 1588 Clock HighDWORD Register (1588_CLOCK_HI) and 1588 Clock Low-DWORD Register (1588_CLOCK_LO).
Upon detection of a clock target compare event, GPIO[9:8] can be configured to output a 100nS pulse,
toggle its output, or reflect the 1588_TIMER_INT bit in the 1588 Interrupt Status and Enable Register
(1588_INT_STS_EN) by enabling the GPIO_EVENT_9 or GPIO_EVENT_8 bits of the 1588
Configuration Register (1588_CONFIG). The clock event polarity, which determines whether the IEEE
1588 GPIO output is active high or active low, is controlled via the GPIO_EVENT_POL_9 and
GPIO_EVENT_POL_8 bits of the General Purpose I/O Configuration Register (GPIO_CFG).
Note: The 1588_GPIO_OE[9:8] bits do not override the GPIO buffer type bits GPIOBUF[9:8] in the
General Purpose I/O Configuration Register (GPIO_CFG).
13.2.2
GPIO Interrupts
Each GPIO of the LAN9312 provides the ability to trigger a unique GPIO interrupt in the General
Purpose I/O Interrupt Status and Enable Register (GPIO_INT_STS_EN). Reading the GPIO_INT[11:0]
bits of this register provides the current status of the corresponding interrupt, and each interrupt is
enabled by setting the corresponding GPIO_INT_EN[11:0] bit. The GPIO/LED Controller aggregates
the enabled interrupt values into an internal signal which is sent to the System Interrupt Controller and
is reflected via the Interrupt Status Register (INT_STS) bit 12 (GPIO). For more information on the
LAN9312 interrupts, refer to Chapter 5, "System Interrupts," on page 49.
13.2.2.1
GPIO Interrupt Polarity
The interrupt polarity can be set for each individual GPIO via the GPIO_INT_POL[11:0] bits in the
General Purpose I/O Configuration Register (GPIO_CFG). When set, a high logic level on the GPIO
pin will set the corresponding interrupt bit in the General Purpose I/O Interrupt Status and Enable
Register (GPIO_INT_STS_EN). When cleared, a low logic level on the GPIO pin will set the
corresponding interrupt bit. Because GPIO[9:8] have added IEEE 1588 functionality, the
SMSC LAN9312
163
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
GPIO_INT_POL[9:8] bits also determine the polarity of the clock events as described in
Section 13.2.1.2.
13.2.2.2
IEEE 1588 GPIO Interrupts
In addition to the standard GPIO interrupts in the General Purpose I/O Interrupt Status and Enable
Register (GPIO_INT_STS_EN), the IEEE 1588 timestamp enabled GPIO[9:8] pins contain the ability
to generate and clear specific IEEE 1588 related interrupts. When GPIO 9 or GPIO 8 are enabled as
inputs and an active edge occurs, the IEEE 1588 clock capture is indicated by the 1588_GPIO9_INT
and 1588_GPIO8_INT interrupts respectively in the 1588 Interrupt Status and Enable Register
(1588_INT_STS_EN). These interrupts are enabled by setting the corresponding 1588_GPIO9_EN
and 1588_GPIO8_EN bits in the 1588 Interrupt Status and Enable Register (1588_INT_STS_EN).
GPIO inputs must be active for greater than 40nS to be recognized as capture events.
When GPIO 8 and GPIO 9 are enabled, the 1588 Timer Interrupt bit (1588_TIMER_INT) of the 1588
Interrupt Status and Enable Register (1588_INT_STS_EN) can be cleared by an active edge on
GPIO[9:8]. A clear is only registered when the GPIO input is active for greater than 40nS.
13.3
LED Operation
Eight pins, GPIO[7:0], are shared with LED functions (nP1LED[3:0] and nP2LED[3:0]). These pins are
configured as LED outputs by setting the corresponding LED_EN bit in the LED Configuration Register
(LED_CFG). When configured as a LED, the pin is an open-drain, active-low output and the GPIO
related input buffer and pull-up are disabled. The LED outputs are always active low. As a result, a
low signal on the LED pin equates to the LED “on”, and a high signal equates to the LED “off”.
The functions associated with each LED pin are configurable via the LED_FUN[1:0] bits of the LED
Configuration Register (LED_CFG). These bits allow the configuration of each LED pin to indicate
various port related functions. These functions are described in Table 13.1 followed by a detailed
definition of each indication type.
The default values of the LED_FUN[1:0] and LED_EN[7:0] bits of the LED Configuration Register
(LED_CFG) are determined by the LED_fun_strap[1:0] and LED_en_strap[7:0] configuration straps.
For more information on the LED Configuration Register (LED_CFG) and its related straps, refer to
Section 14.2.3.4, "LED Configuration Register (LED_CFG)," on page 196.
Table 13.1 LED Operation as a Function of LED_CFG[9:8]
LED_CFG[9:8] (LED_FUN[1:0])
00b
01b
10b
11b
nP2LED3
(GPIO7)
RX
Port 0
RX
Port 0
Activity
Port 2
-
nP2LED2
(GPIO6)
Link / Activity
Port 2
100Link / Activity
Port 2
Link
Port 2
-
nP2LED1
(GPIO5)
Full-duplex / Collision
Port 2
Full-duplex / Collision
Port 2
Full-duplex / Collision
Port 2
TXEN
Port 2
nP2LED0
(GPIO4)
Speed
Port 2
10Link / Activity
Port 2
Speed
Port 2
RXDV
Port 2
nP1LED3
(GPIO3)
TX
Port 0
TX
Port 0
Activity
Port 1
TXEN
Port 0
nP1LED2
(GPIO2)
Link / Activity
Port 1
100Link / Activity
Port 1
Link
Port 1
RXDV
Port 0
Revision 2.0 (02-14-13)
164
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 13.1 LED Operation as a Function of LED_CFG[9:8] (continued)
LED_CFG[9:8] (LED_FUN[1:0])
nP1LED1
(GPIO1)
Full-duplex / Collision
Port 1
Full-duplex / Collision
Port 1
Full-duplex / Collision
Port 1
TXEN
Port 1
nP1LED0
(GPIO0)
Speed
Port 1
10Link / Activity
Port 1
Speed
Port 1
RXDV
Port 1
The various LED indication functions shown in Table 13.1 are described below:

TX Port 0 - The signal is pulsed low for 80mS to indicate activity from the switch fabric to the Host
MAC. This signal is then driven high for a minimum of 80mS, after which the process will repeat if
TX activity is again detected.

RX Port 0 - The signal is pulsed low for 80mS to indicate activity from the Host MAC to the switch
fabric. This signal is then driven high for a minimum of 80mS, after which the process will repeat
if RX activity is again detected.

Link / Activity - A steady low output indicates that the port has a valid link, while a steady high
indicates no link on the port. The signal is pulsed high for 80mS to indicate transmit or receive
activity on the port. The signal is then driven low for a minimum of 80mS, after which the process
will repeat if RX or TX activity is again detected.

Full-duplex / Collision - A steady low output indicates the port is in full-duplex mode, while a
steady high indicates no link on the port. In half-duplex mode, the signal is pulsed low for 80mS
to indicate a network collision. The signal is then driven high for a minimum of 80mS, after which
the process will repeat if another collision is detected.

Speed - A steady low output indicates the selected speed is 100Mbps. A steady high output
indicates the selected speed is 10Mbps. The signal will be held high if the port does not have a
valid link.

100Link / Activity - A steady low output indicates the port has a valid link and the speed is
100Mbps. The signal is pulsed high for 80mS to indicate TX or RX activity on the port. The signal
is then driven low for a minimum of 80mS, after which the process will repeat if RX or TX activity
is again detected. The signal will be held high if the port does not have a valid link.

10Link / Activity - A steady low output indicates the port has a valid link and the speed is 10Mbps.
The signal is pulsed high for 80mS to indicate transmit or receive activity on the port. The signal
is then driven low for a minimum of 80mS, after which the process will repeat if RX or TX activity
is again detected. This signal will be held high if the port does not have a valid link.

Activity - The signal is pulsed low for 80mS to indicate transmit or receive activity. The signal is
then driven high for a minimum of 80mS, after which the process will repeat if RX or TX activity is
again detected. The signal will be held high if the port does not have a valid link.

Link - A steady low indicates the port has a valid link.

TXEN Port 0 - Non-stretched TXEN signal from the switch fabric to the Host MAC.

RXDV Port 0 - Non-stretched RXDV signal from the Host MAC to the switch fabric.

TXEN - Non-stretched TXEN signal from the switch fabric to the PHY.

RXDV - Non-stretched RXDV signal from the PHY to the switch fabric.
SMSC LAN9312
165
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 14 Register Descriptions
This section describes the various LAN9312 control and status registers (CSR’s). These registers are
broken into 5 categories. The following sections detail the functionality and accessibility of all the
LAN9312 registers within each category:

Section 14.1, "TX/RX FIFO Ports," on page 167

Section 14.2, "System Control and Status Registers," on page 168

Section 14.3, "Host MAC Control and Status Registers," on page 270

Section 14.4, "Ethernet PHY Control and Status Registers," on page 286

Section 14.5, "Switch Fabric Control and Status Registers," on page 308
Figure 14.1 contains an overall base register memory map of the LAN9312. This memory map is not
drawn to scale, and should be used for general reference only.
Note: Register bit type definitions are provided in Section 1.3, "Register Nomenclature," on page 19.
Note: Not all LAN9312 registers are memory mapped or directly addressable. For details on the
accessibility of the various LAN9312 registers, refer the register sub-sections listed above.
3FFh
...
RESERVED
2E0h
2DCh
...
Switch CSR Direct Data
Registers
200h
1DCh
Virtual PHY Registers
1C0h
1B0h
1ACh
Switch Interface Registers
19Ch
System CSRs
1588 Registers
100h
Host MAC Interface Registers
050h
04Ch
048h
044h
040h
03Ch
TX Status FIFO PEEK
TX Status FIFO Port
RX Status FIFO PEEK
RX Status FIFO Port
020h
01Ch
Base + 000h
TX Data FIFO Port
& Alias Ports
RX Data FIFO Port
& Alias Ports
TX/RX FIFOs
0A8h
0A4h
Figure 14.1 LAN9312 Base Register Memory Map
Revision 2.0 (02-14-13)
166
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.1
TX/RX FIFO Ports
The LAN9312 contains four host-accessible FIFO’s: TX Status, RX Status, TX Data, and RX Data.
These FIFO’s store the incoming and outgoing address and data information, acting as a conduit
between the host bus interface (HBI) and the Host MAC. The sizes of these FIFO’s are configurable
via the Hardware Configuration Register (HW_CFG). Refer to Section 9.7.3, "FIFO Memory Allocation
Configuration," on page 121 for additional information on FIFO size configuration.
For additional information on the FIFO configuration registers accessible via the Host Bus Interface,
refer to their respective register definitions located in section Section 14.2.2, "Host MAC & FIFO’s".
14.1.1
TX/RX Data FIFO’s
The TX and RX Data FIFO ports have the base address of 020h and 000h respectively. However, each
FIFO is also accessible at seven additional contiguous memory locations, as can be seen in
Figure 14.1. The Host may access the TX or RX Data FIFO’s at any of these alias port locations, as
they all function identically and contain the same data. This alias port addressing is implemented to
allow hosts to burst through sequential addresses.
14.1.2
TX/RX Status FIFO’s
The TX and RX Status FIFO’s can each be read from two register locations; the Status FIFO Port, and
the Status FIFO PEEK. The TX and RX Status FIFO Ports (048h and 040h respectively) will perform
a destructive read, popping the data from the TX or RX Status FIFO. The TX and RX Status FIFO
PEEK register locations (04Ch and 044h respectively) allow a non-destructive read of the top (oldest)
location of the FIFO’s.
14.1.3
Direct FIFO Access Mode
When the FIFO_SEL pin is driven high, the LAN9312 enters the direct FIFO access mode. In this
mode, all host write operations are to the TX Data FIFO and all host read operations are from the RX
Data FIFO. When FIFO_SEL is asserted, only the A[2] host address signal is decoded. All other
address signals are ignored in this mode. When the endianess select pin (END_SEL) is low, the TX/RX
Data FIFO’s are accessed in little endian mode. When END_SEL is high, the TX/RX Data FIFO’s are
accessed in big endian mode. The A[2] input is used during Data FIFO direct PIO burst cycles to
delimit DWORD accesses. For more information on endianess selection, refer to section Section 8.3,
"Host Endianess".
SMSC LAN9312
167
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2
System Control and Status Registers
The System CSR’s are directly addressable memory mapped registers with a base address offset
range of 050h to 2DCh. These registers are addressable by the Host via the Host Bus Interface (HBI).
Table 14.1 lists the System CSR’s and their corresponding addresses in order. All system CSR’s are
reset to their default value on the assertion of a chip-level reset.
The System CSR’s can be divided into 9 sub-categories. Each of these sub-categories contains the
System CSR descriptions of the associated registers. The register descriptions are categorized as
follows:

Section 14.2.1, "Interrupts," on page 172

Section 14.2.2, "Host MAC & FIFO’s," on page 180

Section 14.2.3, "GPIO/LED," on page 192

Section 14.2.4, "EEPROM," on page 197

Section 14.2.5, "IEEE 1588," on page 201

Section 14.2.6, "Switch Fabric," on page 229

Section 14.2.7, "PHY Management Interface (PMI)," on page 243

Section 14.2.8, "Virtual PHY," on page 245

Section 14.2.9, "Miscellaneous," on page 259
Table 14.1 System Control and Status Registers
ADDRESS
OFFSET
SYMBOL
050h
ID_REV
Chip ID and Revision Register, Section 14.2.9.1
054h
IRQ_CFG
Interrupt Configuration Register, Section 14.2.1.1
058h
INT_STS
Interrupt Status Register, Section 14.2.1.2
05Ch
INT_EN
Interrupt Enable Register, Section 14.2.1.3
060h
RESERVED
Reserved for Future Use
064h
BYTE_TEST
Byte Order Test Register, Section 14.2.9.2
068h
FIFO_INT
FIFO Level Interrupts Register, Section 14.2.1.4
06Ch
RX_CFG
Receive Configuration Register, Section 14.2.2.1
070h
TX_CFG
Transmit Configuration Register, Section 14.2.2.2
074h
HW_CFG
Hardware Configuration Register, Section 14.2.9.3
078h
RX_DP_CTRL
RX Datapath Control Register, Section 14.2.2.3
07Ch
RX_FIFO_INF
Receive FIFO Information Register,Section 14.2.2.4
080h
TX_FIFO_INF
Transmit FIFO Information Register, Section 14.2.2.5
084h
PMT_CTRL
Power Management Control Register, Section 14.2.9.4
088h
RESERVED
Reserved for Future Use
08Ch
GPT_CFG
General Purpose Timer Configuration Register,
Section 14.2.9.5
090h
GPT_CNT
General Purpose Timer Count Register, Section 14.2.9.6
094h - 098h
RESERVED
Revision 2.0 (02-14-13)
REGISTER NAME
Reserved for Future Use
168
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.1 System Control and Status Registers (continued)
ADDRESS
OFFSET
SYMBOL
09Ch
FREE_RUN
Free Running Counter Register, Section 14.2.9.7
0A0h
RX_DROP
Host MAC RX Dropped Frames Counter Register,
Section 14.2.2.6
0A4h
MAC_CSR_CMD
0A4h
EEPROM
Loader
Access Only
PMI_DATA
0A8h
MAC_CSR_DATA
Host MAC CSR Interface Data Register, Section 14.2.2.8
0A8h
EEPROM
Loader
Access Only
PMI_ACCESS
PHY Management Interface Access Register (EEPROM
Loader Access Only), Section 14.2.7.2
0ACh
AFC_CFG
0B0h - 0FCh
RESERVED
100h
1588_CLOCK_HI_RX_CAPTURE_1
Port 1 1588 Clock High-DWORD Receive Capture
Register, Section 14.2.5.1
104h
1588_CLOCK_LO_RX_CAPTURE_1
Port 1 1588 Clock Low-DWORD Receive Capture Register,
Section 14.2.5.2
108h
1588_SEQ_ID_SRC_UUID_HI_RX_CAPTURE_1
10Ch
1588_SRC_UUID_LO_RX_CAPTURE_1
110h
1588_CLOCK_HI_TX_CAPTURE_1
Port 1 1588 Clock High-DWORD Transmit Capture
Register, Section 14.2.5.5
114h
1588_CLOCK_LO_TX_CAPTURE_1
Port 1 1588 Clock Low-DWORD Transmit Capture
Register, Section 14.2.5.6
118h
1588_SEQ_ID_SRC_UUID_HI_TX_CAPTURE_1
11C
1588_SRC_UUID_LO_TX_CAPTURE_1
120h
1588_CLOCK_HI_RX_CAPTURE_2
Port 2 1588 Clock High-DWORD Receive Capture
Register, Section 14.2.5.1
124h
1588_CLOCK_LO_RX_CAPTURE_2
Port 2 1588 Clock Low-DWORD Receive Capture Register,
Section 14.2.5.2
128h
1588_SEQ_ID_SRC_UUID_HI_RX_CAPTURE_2
12Ch
1588_SRC_UUID_LO_RX_CAPTURE_2
130h
1588_CLOCK_HI_TX_CAPTURE_2
Port 2 1588 Clock High-DWORD Transmit Capture
Register, Section 14.2.5.5
134h
1588_CLOCK_LO_TX_CAPTURE_2
Port 2 1588 Clock Low-DWORD Transmit Capture
Register, Section 14.2.5.6
138h
1588_SEQ_ID_SRC_UUID_HI_TX_CAPTURE_2
SMSC LAN9312
REGISTER NAME
Host MAC CSR Interface Command Register,
Section 14.2.2.7
PHY Management Interface Data Register (EEPROM
Loader Access Only), Section 14.2.7.1
Host MAC Automatic Flow Control Configuration Register,
Section 14.2.2.9
Reserved for Future Use
Port 1 1588 Sequence ID, Source UUID High-WORD
Receive Capture Register, Section 14.2.5.3
Port 1 1588 Source UUID Low-DWORD Receive Capture
Register, Section 14.2.5.4
Port 1 1588 Sequence ID, Source UUID High-WORD
Transmit Capture Register, Section 14.2.5.7
Port 1 1588 Source UUID Low-DWORD Transmit Capture
Register, Section 14.2.5.8
Port 2 1588 Sequence ID, Source UUID High-WORD
Receive Capture Register, Section 14.2.5.3
Port 2 1588 Source UUID Low-DWORD Receive Capture
Register, Section 14.2.5.4
169
Port 2 1588 Sequence ID, Source UUID High-WORD
Transmit Capture Register, Section 14.2.5.7
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.1 System Control and Status Registers (continued)
ADDRESS
OFFSET
SYMBOL
REGISTER NAME
13Ch
1588_SRC_UUID_LO_TX_CAPTURE_2
Port 2 1588 Source UUID Low-DWORD Transmit Capture
Register, Section 14.2.5.8
140h
1588_CLOCK_HI_RX_CAPTURE_MII
Port 0 1588 Clock High-DWORD Receive Capture
Register, Section 14.2.5.1
144h
1588_CLOCK_LO_RX_CAPTURE_MII
Port 0 1588 Clock Low-DWORD Receive Capture Register,
Section 14.2.5.2
148h
1588_SEQ_ID_SRC_UUID_HI_RX_CAPTURE_MII
14Ch
1588_SRC_UUID_LO_RX_CAPTURE_MII
150h
1588_CLOCK_HI_TX_CAPTURE_MII
Port 0 1588 Clock High-DWORD Transmit Capture
Register, Section 14.2.5.5
154h
1588_CLOCK_LO_TX_CAPTURE_MII
Port 0 1588 Clock Low-DWORD Transmit Capture
Register, Section 14.2.5.6
158h
1588_SEQ_ID_SRC_UUID_HI_TX_CAPTURE_MII
15Ch
1588_SRC_UUID_LO_TX_CAPTURE_MII
160h
1588_CLOCK_HI_CAPTURE_GPIO_8
GPIO 8 1588 Clock High-DWORD Capture Register,
Section 14.2.5.9
164h
1588_CLOCK_LO_CAPTURE_GPIO_8
GPIO 8 1588 Clock Low-DWORD Capture Register,
Section 14.2.5.10
168h
1588_CLOCK_HI_CAPTURE_GPIO_9
GPIO 9 1588 Clock High-DWORD Capture Register,
Section 14.2.5.11
16Ch
1588_CLOCK_LO_CAPTURE_GPIO_9
GPIO 9 1588 Clock Low-DWORD Capture Register,
Section 14.2.5.12
170h
1588_CLOCK_HI
1588 Clock High-DWORD Register, Section 14.2.5.13
174h
1588_CLOCK_LO
1588 Clock Low-DWORD Register, Section 14.2.5.14
178h
1588_CLOCK_ADDEND
17Ch
1588_CLOCK_TARGET_HI
1588 Clock Target High-DWORD Register,
Section 14.2.5.16
180h
1588_CLOCK_TARGET_LO
1588 Clock Target Low-DWORD Register,
Section 14.2.5.17
184h
1588_CLOCK_TARGET_RELOAD_HI
1588 Clock Target Reload High-DWORD Register,
Section 14.2.5.18
188h
1588_CLOCK_TARGET_RELOAD_LO
1588 Clock Target Reload/Add Low-DWORD Register,
Section 14.2.5.19
18Ch
1588_AUX_MAC_HI
1588 Auxiliary MAC Address High-WORD Register,
Section 14.2.5.20
190h
1588_AUX_MAC_LO
1588 Auxiliary MAC Address Low-DWORD Register,
Section 14.2.5.21
194h
1588_CONFIG
198h
1588_INT_STS_EN
19Ch
1588_CMD
Revision 2.0 (02-14-13)
Port 0 1588 Sequence ID, Source UUID High-WORD
Receive Capture Register, Section 14.2.5.3
Port 0 1588 Source UUID Low-DWORD Receive Capture
Register, Section 14.2.5.4
Port 0 1588 Sequence ID, Source UUID High-WORD
Transmit Capture Register, Section 14.2.5.7
Port 0 1588 Source UUID Low-DWORD Transmit Capture
Register, Section 14.2.5.8
1588 Clock Addend Register, Section 14.2.5.15
1588 Configuration Register, Section 14.2.5.22
1588 Interrupt Status Enable Register, Section 14.2.5.23
1588 Command Register, Section 14.2.5.24
170
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.1 System Control and Status Registers (continued)
ADDRESS
OFFSET
SYMBOL
1A0h
MANUAL_FC_1
Port 1 Manual Flow Control Register, Section 14.2.6.1
1A4h
MANUAL_FC_2
Port 2 Manual Flow Control Register, Section 14.2.6.2
1A8h
MANUAL_FC_MII
1ACh
SWITCH_CSR_DATA
Switch Fabric CSR Interface Data Register,
Section 14.2.6.4
1B0h
SWITCH_CSR_CMD
Switch Fabric CSR Interface Command Register,
Section 14.2.6.5
1B4h
E2P_CMD
EEPROM Command Register, Section 14.2.4.1
1B8h
E2P_DATA
EEPROM Data Register, Section 14.2.4.2
1BCh
LED_CFG
LED Configuration Register, Section 14.2.3.4
1C0h
VPHY_BASIC_CTRL
Virtual PHY Basic Control Register, Section 14.2.8.1
1C4h
VPHY_BASIC_STATUS
Virtual PHY Basic Status Register, Section 14.2.8.2
1C8h
VPHY_ID_MSB
Virtual PHY Identification MSB Register, Section 14.2.8.3
1CCh
VPHY_ID_LSB
Virtual PHY Identification LSB Register, Section 14.2.8.4
1D0h
VPHY_AN_ADV
Virtual PHY Auto-Negotiation Advertisement Register,
Section 14.2.8.5
1D4h
VPHY_AN_LP_BASE_ABILITY
Virtual PHY Auto-Negotiation Link Partner Base Page
Ability Register, Section 14.2.8.6
1D8h
VPHY_AN_EXP
1DCh
VPHY_SPECIAL_CONTROL_STATUS
Virtual PHY Special Control/Status Register,
Section 14.2.8.8
1E0h
GPIO_CFG
General Purpose I/O Configuration Register,
Section 14.2.3.1
1E4h
GPIO_DATA_DIR
1E8h
GPIO_INT_STS_EN
1ECh
RESERVED
1F0h
SWITCH_MAC_ADDRH
Switch MAC Address High Register, Section 14.2.6.6
1F4h
SWITCH_MAC_ADDRL
Switch MAC Address Low Register, Section 14.2.6.7
1F8h
RESET_CTL
Reset Control Register, Section 14.2.9.8
1FCh
RESERVED
Reserved for Future Use
200h-2DCh
SWITCH_CSR_DIRECT_DATA
2E0h-3FFh
RESERVED
SMSC LAN9312
REGISTER NAME
Port 0 Flow Control Register, Section 14.2.6.3
Virtual PHY Auto-Negotiation Expansion Register,
Section 14.2.8.7
General Purpose I/O Data & Direction Register,
Section 14.2.3.2
General Purpose I/O Interrupt Status and Enable Register,
Section 14.2.3.3
Reserved for Future Use
Switch Engine CSR Interface Direct Data Register,
Section 14.2.6.8
Reserved for Future Use
171
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.1
Interrupts
This section details the interrupt related System CSR’s. These registers control, configure, and monitor
the IRQ interrupt output pin and the various LAN9312 interrupt sources. For more information on the
LAN9312 interrupts, refer to Chapter 5, "System Interrupts," on page 49.
14.2.1.1
Interrupt Configuration Register (IRQ_CFG)
Offset:
054h
Size:
32 bits
This read/write register configures and indicates the state of the IRQ signal.
BITS
DESCRIPTION
TYPE
DEFAULT
31:24
Interrupt De-assertion Interval (INT_DEAS)
This field determines the Interrupt Request De-assertion Interval in multiples
of 10 microseconds.
R/W
00h
RESERVED
RO
-
Interrupt De-assertion Interval Clear (INT_DEAS_CLR)
Writing a 1 to this register clears the de-assertion counter in the Interrupt
Controller, thus causing a new de-assertion interval to begin (regardless of
whether or not the Interrupt Controller is currently in an active de-assertion
interval).
R/W
SC
0h
RO
SC
0b
RO
0b
RESERVED
RO
-
IRQ Enable (IRQ_EN)
This bit controls the final interrupt output to the IRQ pin. When clear, the IRQ
output is disabled and permanently de-asserted. This bit has no effect on
any internal interrupt status bits.
R/W
0b
RO
-
Setting this field to zero causes the device to disable the INT_DEAS Interval,
reset the interval counter and issue any pending interrupts. If a new, nonzero value is written to this field, any subsequent interrupts will obey the new
setting.
This field does not apply to the PME_INT interrupt.
23:15
14
0: Normal operation
1: Clear de-assertion counter
13
Interrupt De-assertion Status (INT_DEAS_STS)
When set, this bit indicates that interrupts are currently in a de-assertion
interval, and will not be sent to the IRQ pin. When this bit is clear, interrupts
are not currently in a de-assertion interval, and will be sent to the IRQ pin.
0: No interrupts in de-assertion interval
1: Interrupts in de-assertion interval
12
Master Interrupt (IRQ_INT)
This read-only bit indicates the state of the internal IRQ line, regardless of
the setting of the IRQ_EN bit, or the state of the interrupt de-assertion
function. When this bit is set, one of the enabled interrupts is currently
active.
0: No enabled interrupts active
1: One or more enabled interrupts active
11:9
8
0: Disable output on IRQ pin
1: Enable output on IRQ pin
7:5
RESERVED
Revision 2.0 (02-14-13)
172
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
4
IRQ Polarity (IRQ_POL)
When cleared, this bit enables the IRQ line to function as an active low
output. When set, the IRQ output is active high. When the IRQ is configured
as an open-drain output (via the IRQ_TYPE bit), this bit is ignored, and the
interrupt is always active low.
R/W
NASR
0b
Note 14.1
0: IRQ active low output
1: IRQ active high output
3:1
0
RESERVED
IRQ Buffer Type (IRQ_TYPE)
When this bit is cleared, the IRQ pin functions as an open-drain output for
use in a wired-or interrupt configuration. When set, the IRQ is a push-pull
driver.
RO
-
R/W
NASR
0b
Note 14.1
Note:
When configured as an open-drain output, the IRQ_POL bit is
ignored and the interrupt output is always active low.
0: IRQ pin open-drain output
1: IRQ pin push-pull driver
Note 14.1 Register bits designated as NASR are not reset when either the SRST bit in the Hardware
Configuration Register (HW_CFG) register or the DIGITAL_RST bit in the Reset Control
Register (RESET_CTL) is set.
SMSC LAN9312
173
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.1.2
Interrupt Status Register (INT_STS)
Offset:
058h
Size:
32 bits
This register contains the current status of the generated interrupts. A value of 1 indicates the
corresponding interrupt conditions have been met, while a value of 0 indicates the interrupt conditions
have not been met. The bits of this register reflect the status of the interrupt source regardless of
whether the source has been enabled as an interrupt in the Interrupt Enable Register (INT_EN). Where
indicated as R/WC, writing a 1 to the corresponding bits acknowledges and clears the interrupt.
BITS
DESCRIPTION
TYPE
DEFAULT
31
Software Interrupt (SW_INT)
This interrupt is generated when the SW_INT_EN bit of the Interrupt Enable
Register (INT_EN) is set high. Writing a one clears this interrupt.
R/WC
0b
30
Device Ready (READY)
This interrupt indicates that the LAN9312 is ready to be accessed after a
power-up or reset condition.
R/WC
0b
29
1588 Interrupt Event (1588_EVNT)
This bit indicates an interrupt event from the IEEE 1588 module. This bit
should be used in conjunction with the 1588 Interrupt Status and Enable
Register (1588_INT_STS_EN) to determine the source of the interrupt
event within the 1588 module.
RO
0b
28
Switch Fabric Interrupt Event (SWITCH_INT)
This bit indicates an interrupt event from the Switch Fabric. This bit should
be used in conjunction with the Switch Global Interrupt Pending Register
(SW_IPR) to determine the source of the interrupt event within the Switch
Fabric.
RO
0b
27
Port 2 PHY Interrupt Event (PHY_INT2)
This bit indicates an interrupt event from the Port 2 PHY. The source of the
interrupt can be determined by polling the Port x PHY Interrupt Source
Flags Register (PHY_INTERRUPT_SOURCE_x).
RO
0b
26
Port 1 PHY Interrupt Event (PHY_INT1)
This bit indicates an interrupt event from the Port 1 PHY. The source of the
interrupt can be determined by polling the Port x PHY Interrupt Source
Flags Register (PHY_INTERRUPT_SOURCE_x).
RO
0b
25
TX Stopped (TXSTOP_INT)
This interrupt is issued when STOP_TX bit in Transmit Configuration
Register (TX_CFG) is set, and the Host MAC transmitter is halted.
R/WC
0b
24
RX Stopped (RXSTOP_INT)
This interrupt is issued when the Host MAC receiver is halted.
R/WC
0b
23
RX Dropped Frame Counter Halfway (RXDFH_INT)
This interrupt is issued when the Host MAC RX Dropped Frames Counter
Register (RX_DROP) counts past its halfway point (7FFFFFFFh to
80000000h).
R/WC
0b
22
RESERVED
RO
-
21
TX IOC Interrupt (TX_IOC)
This interrupt is generated when a buffer with the IOC flag set has been
fully loaded into the TX Data FIFO.
R/WC
0b
20
RX DMA Interrupt (RXD_INT)
This interrupt is issued when the amount of data programmed in the RX
DMA Count (RX_DMA_CNT) field of the Receive Configuration Register
(RX_CFG) has been transferred out of the RX Data FIFO.
R/WC
0b
Revision 2.0 (02-14-13)
174
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
19
GP Timer (GPT_INT)
This interrupt is issued when the General Purpose Timer Count Register
(GPT_CNT) wraps past zero to FFFFh.
18
RESERVED
17
Power Management Interrupt Event (PME_INT)
This interrupt is issued when a Power Management Event is detected as
configured in the Power Management Control Register (PMT_CTRL). This
interrupt functions independent of the PME signal, and will still function if
the PME signal is disabled. Writing a '1' clears this bit regardless of the
state of the PME hardware signal. In order to clear this bit, all unmasked
bits in the Power Management Control Register (PMT_CTRL) must first be
cleared.
Note:
TYPE
DEFAULT
R/WC
0b
RO
-
R/WC
0b
The Interrupt De-assertion interval does not apply to the PME
interrupt.
16
TX Status FIFO Overflow (TXSO)
This interrupt is generated when the TX Status FIFO overflows.
R/WC
0b
15
Receive Watchdog Time-out (RWT)
This interrupt is generated when a packet larger than 2048 bytes has been
received by the Host MAC.
R/WC
0b
Note:
This can occur when the switch engine adds a tag to a non-tagged
jumbo packet that is originally larger than 2044 bytes.
14
Receiver Error (RXE)
Indicates that the Host MAC receiver has encountered an error. Please
refer to Section 9.9.5, "Receiver Errors," on page 136 for a description of
the conditions that will cause an RXE.
R/WC
0b
13
Transmitter Error (TXE)
When generated, indicates that the Host MAC transmitter has encountered
an error. Please refer to Section 9.8.7, "Transmitter Errors," on page 131
for a description of the conditions that will cause a TXE.
R/WC
0b
12
GPIO Interrupt Event (GPIO)
This bit indicates an interrupt event from the General Purpose I/O. The
source of the interrupt can be determined by polling the General Purpose
I/O Interrupt Status and Enable Register (GPIO_INT_STS_EN)
RO
0b
11
RESERVED
RO
-
10
TX Data FIFO Overrun Interrupt (TDFO)
This interrupt is generated when the TX Data FIFO is full, and another write
is attempted.
R/WC
0b
9
TX Data FIFO Available Interrupt (TDFA)
This interrupt is generated when the TX Data FIFO available space is
greater than the programmed level in the TX Data Available Level field of
the FIFO Level Interrupt Register (FIFO_INT).
R/WC
0b
8
TX Status FIFO Full Interrupt (TSFF)
This interrupt is generated when the TX Status FIFO is full.
R/WC
0b
7
TX Status FIFO Level Interrupt (TSFL)
This interrupt is generated when the TX Status FIFO reaches the
programmed level in the TX Status Level field of the FIFO Level Interrupt
Register (FIFO_INT).
R/WC
0b
6
RX Dropped Frame Interrupt (RXDF_INT)
This interrupt is issued whenever a receive frame is dropped by the Host
MAC.
R/WC
0b
5
RESERVED
RO
-
SMSC LAN9312
175
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
4
RX Status FIFO Full Interrupt (RSFF)
This interrupt is generated when the RX Status FIFO is full.
R/WC
0b
3
RX Status FIFO Level Interrupt (RSFL)
This interrupt is generated when the RX Status FIFO reaches the
programmed level in the RX Status Level field of the FIFO Level Interrupt
Register (FIFO_INT).
R/WC
0b
RO
-
2:0
RESERVED
Revision 2.0 (02-14-13)
176
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.1.3
Interrupt Enable Register (INT_EN)
Offset:
05Ch
Size:
32 bits
This register contains the interrupt enables for the IRQ output pin. Writing 1 to any of the bits enables
the corresponding interrupt as a source for IRQ. Bits in the Interrupt Status Register (INT_STS) register
will still reflect the status of the interrupt source regardless of whether the source is enabled as an
interrupt in this register (with the exception of SW_INT_EN). For descriptions of each interrupt, refer
to the Interrupt Status Register (INT_STS) bits, which mimic the layout of this register.
BITS
DESCRIPTION
TYPE
DEFAULT
31
Software Interrupt Enable (SW_INT_EN)
R/W
0b
30
Device Ready Enable (READY_EN)
R/W
0b
29
1588 Interrupt Event Enable (1588_EVNT_EN)
R/W
0b
28
Switch Engine Interrupt Event Enable (SWITCH_INT_EN)
R/W
0b
27
Port 2 PHY Interrupt Event Enable (PHY_INT2_EN)
R/W
0b
26
Port 1 PHY Interrupt Event Enable (PHY_INT1_EN)
R/W
0b
25
TX Stopped Interrupt Enable (TXSTOP_INT_EN)
R/W
0b
24
RX Stopped Interrupt Enable (RXSTOP_INT_EN)
R/W
0b
23
RX Dropped Frame Counter Halfway Interrupt Enable
(RXDFH_INT_EN)
R/W
0b
22
RESERVED
RO
-
21
TX IOC Interrupt Enable (TIOC_INT_EN)
R/W
0b
20
RX DMA Interrupt Enable (RXD_INT_EN)
R/W
0b
19
GP Timer Interrupt Enable (GPT_INT_EN)
R/W
0b
18
RESERVED
RO
-
17
Power Management Event Interrupt Enable (PME_INT_EN)
R/W
0b
16
TX Status FIFO Overflow Interrupt Enable (TXSO_EN)
R/W
0b
15
Receive Watchdog Time-out Interrupt Enable (RWT_INT_EN)
R/W
0b
14
Receiver Error Interrupt Enable (RXE_INT_EN)
R/W
0b
13
Transmitter Error Interrupt Enable (TXE_INT_EN)
R/W
0b
12
GPIO Interrupt Event Enable (GPIO_EN)
R/W
0b
11
RESERVED - This bit must be written with 0b for proper operation.
R/W
0b
10
TX Data FIFO Overrun Interrupt Enable (TDFO_EN)
R/W
0b
9
TX Data FIFO Available Interrupt Enable (TDFA_EN)
R/W
0b
8
TX Status FIFO Full Interrupt Enable (TSFF_EN)
R/W
0b
7
TX Status FIFO Level Interrupt Enable (TSFL_EN)
R/W
0b
6
RX Dropped Frame Interrupt Enable (RXDF_INT_EN)
R/W
0b
SMSC LAN9312
177
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
5
RESERVED - This bit must be written with 0b for proper operation.
R/W
0b
4
RX Status FIFO Full Interrupt Enable (RSFF_EN)
R/W
0b
3
RX Status FIFO Level Interrupt Enable (RSFL_EN)
R/W
0b
RESERVED
RO
-
2:0
Revision 2.0 (02-14-13)
178
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.1.4
FIFO Level Interrupt Register (FIFO_INT)
Offset:
068h
Size:
32 bits
This read/write register configures the limits where the RX/TX Data and Status FIFO’s will generate
system interrupts.
BITS
DESCRIPTION
TYPE
DEFAULT
31:24
TX Data Available Level
The value in this field sets the level, in number of 64 Byte blocks, at which
the TX Data FIFO Available Interrupt (TDFA) will be generated. When the
TX Data FIFO free space is greater than this value, a TX Data FIFO
Available Interrupt (TDFA) will be generated in the Interrupt Status Register
(INT_STS).
R/W
48h
23:16
TX Status Level
The value in this field sets the level, in number of DWORD’s, at which the
TX Status FIFO Level Interrupt (TSFL) will be generated. When the TX
Status FIFO used space is greater than this value, a TX Status FIFO Level
Interrupt (TSFL) will be generated in the Interrupt Status Register
(INT_STS).
R/W
00h
15:8
RESERVED - This field must be written with 00h for proper operation.
R/W
00h
7:0
RX Status Level
The value in this field sets the level, in number of DWORD’s, at which the
RX Status FIFO Level Interrupt (RSFL) will be generated. When the RX
Status FIFO used space is greater than this value, a RX Status FIFO Level
Interrupt (RSFL) will be generated in the Interrupt Status Register
(INT_STS).
R/W
00h
SMSC LAN9312
179
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.2
Host MAC & FIFO’s
This section details the Host MAC and TX/RX FIFO related System CSR’s.
These Host Bus Interface accessible registers allow for the configuration of the TX/RX FIFO’s, Host
MAC and indirect access to the complete set of Host MAC CSR’s. The Host MAC CSR’s are
accessible through the Host Bus Interface via the Host MAC CSR Interface Command Register
(MAC_CSR_CMD) and Host MAC CSR Interface Data Register (MAC_CSR_DATA).
Note: For more information on the TX/RX FIFO’s, refer to Section 14.1, "TX/RX FIFO Ports".
Note: The full list of Host MAC CSR’s are described in Section 14.3, "Host MAC Control and Status
Registers," on page 270. For more information on the Host MAC, refer to Chapter 9, "Host
MAC," on page 112.
14.2.2.1
Receive Configuration Register (RX_CFG)
Offset:
06Ch
Size:
32 bits
This register controls the Host MAC receive engine.
BITS
DESCRIPTION
TYPE
DEFAULT
31:30
RX End Alignment (RX_EA)
This field specifies the alignment that must be maintained on the last data
transfer of a buffer. The LAN9312 will add extra DWORD’s of data up to
the alignment specified in the table below. The host is responsible for
removing these extra DWORD’s. This mechanism can be used to maintain
cache line alignment on host processors.
R/W
00b
BIT
VALUES
[31:30]
END ALIGNMENT
00
4-Byte Alignment
01
16-Byte Alignment
10
32-Byte Alignment
11
RESERVED
Note:
The desired RX End Alignment must be set before reading a
packet. The RX End Alignment can be changed between reading
receive packets, but must not be changed if the packet is partially
read.
29:28
RESERVED
RO
-
27:16
RX DMA Count (RX_DMA_CNT)
This 12-bit field indicates the amount of data, in DWORD’s, to be
transferred out of the RX Data FIFO before asserting the RX DMA Interrupt
(RXD_INT). After being set, this field is decremented for each DWORD of
data that is read from the RX Data FIFO. This field can be overwritten with
a new value before it reaches zero.
R/W
000h
Revision 2.0 (02-14-13)
180
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
15
Force RX Discard (RX_DUMP)
When a 1 is written to this bit, the RX Data and Status FIFO’s are cleared
of all pending data and the RX data and status pointers are cleared to zero.
WO
SC
0b
Note:
Please refer to Section 9.9.1.2, "Force Receiver Discard (Receiver
Dump)," on page 134 for a detailed description regarding the use
of RX_DUMP.
14:13
RESERVED
RO
-
12:8
RX Data Offset (RXDOFF)
This field controls the offset value, in bytes, that is added to the beginning
of an RX data packet. The start of the valid data will be shifted by the
number of bytes specified in this field. An offset of 0-31 bytes is a valid
number of offset bytes.
R/W
00000b
RO
-
Note:
7:0
The two LSBs of this field (D[9:8]) must not be modified while the
RX is running. The receiver must be halted, and all data purged
before these two bits can be modified. The upper three bits
(DWORD offset) may be modified while the receiver is running.
Modifications to the upper bits will take affect on the next DWORD
read.
RESERVED
SMSC LAN9312
181
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.2.2
Transmit Configuration Register (TX_CFG)
Offset:
070h
Size:
32 bits
This register controls the Host MAC transmit functions.
BITS
TYPE
DEFAULT
RESERVED
RO
-
15
Force TX Status Discard (TXS_DUMP)
When a 1 is written to this bit, the TX Status FIFO is cleared of all pending
status DWORD’s and the TX status pointers are cleared to zero.
WO
SC
0b
14
Force TX Data Discard (TXD_DUMP)
When a 1 is written to this bit, the TX Data FIFO is cleared of all pending
data and the TX data pointers are cleared to zero.
WO
SC
0b
RESERVED
RO
-
TX Status Allow Overrun (TXSAO)
When this bit is cleared, Host MAC data transmission is suspended if the
TX Status FIFO becomes full. Setting this bit high allows the transmitter to
continue operation with a full TX Status FIFO.
R/W
0b
31:16
13:3
2
DESCRIPTION
Note:
This bit does not affect the operation of the TX Status FIFO Full
Interrupt (TSFF).
1
Transmitter Enable (TX_ON)
When this bit is set, the Host MAC transmitter is enabled. Any data in the
TX Data FIFO will be sent. This bit is cleared automatically when the
STOP_TX bit is set and the transmitter is halted.
R/W
0b
0
Stop Transmitter (STOP_TX)
When this bit is set, the Host MAC transmitter will finish the current frame,
and will then stop transmitting. When the transmitter has stopped this bit will
clear. All writes to this bit are ignored while this bit is high.
R/W
SC
0b
Revision 2.0 (02-14-13)
182
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.2.3
Receive Datapath Control Register (RX_DP_CTRL)
Offset:
078h
Size:
32 bits
This register is used to discard unwanted receive frames.
BITS
DESCRIPTION
TYPE
DEFAULT
31
RX Data FIFO Fast Forward (RX_FFWD)
Writing a 1 to this bit causes the RX Data FIFO to fast-forward to the start
of the next frame. This bit will remain high until the RX Data FIFO fastforward operation has completed. No reads should be issued to the RX Data
FIFO while this bit is high.
R/W
SC
0h
RO
-
Note:
30:0
Please refer to section Section 9.9.1.1, "Receive Data FIFO Fast
Forward," on page 134 for detailed information regarding the use
of RX_FFWD.
RESERVED
SMSC LAN9312
183
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.2.4
RX FIFO Information Register (RX_FIFO_INF)
Offset:
07Ch
Size:
32 bits
This register contains the indication of used space in the RX FIFO’s.
BITS
DESCRIPTION
TYPE
DEFAULT
31:24
RESERVED
RO
-
23:16
RX Status FIFO Used Space (RXSUSED)
This field indicates the amount of space, in DWORD’s, currently used in the
RX Status FIFO.
RO
0b
15:0
RX Data FIFO Used Space (RXDUSED)
This field indicates the amount of space, in bytes, used in the RX Data FIFO.
For each receive frame, the field is incremented by the length of the receive
data. In cases where the payload does not end on a DWORD boundary, the
total will be rounded up to the nearest DWORD.
RO
0b
Revision 2.0 (02-14-13)
184
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.2.5
TX FIFO Information Register (TX_FIFO_INF)
Offset:
080h
Size:
32 bits
This register contains the indication of free space in the TX Data FIFO and the used space in the TX
Status FIFO.
BITS
DESCRIPTION
TYPE
DEFAULT
31:24
RESERVED
RO
-
23:16
TX Status FIFO Used Space (TXSUSED)
This field indicates the amount of space, in DWORD’s, currently used in the
TX Status FIFO.
RO
0b
15:0
TX Data FIFO Free Space (TXFREE)
This field indicates the amount of space, in bytes, available in the TX Data
FIFO. The application should never write more than is available, as indicated
by this value.
RO
1200h
SMSC LAN9312
185
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.2.6
Host MAC RX Dropped Frames Counter Register (RX_DROP)
Offset:
0A0h
Size:
32 bits
This register indicates the number of receive frames that have been dropped by the Host MAC.
BITS
31:0
DESCRIPTION
RX Dropped Frame Counter (RX_DFC)
This counter is incremented every time a receive frame is dropped by the
Host MAC. RX_DFC is cleared on any read of this register.
Note:
TYPE
DEFAULT
RC
00000000h
The interrupt RXDFH_INT (bit 23 of the Interrupt Status Register
(INT_STS)) can be issued when this counter passes through its
halfway point (7FFFFFFFh to 80000000h).
Revision 2.0 (02-14-13)
186
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.2.7
Host MAC CSR Interface Command Register (MAC_CSR_CMD)
Offset:
0A4h
Size:
32 bits
This read-write register is used to control the read and write operations to/from the Host MAC. This
register in used in conjunction with the Host MAC CSR Interface Data Register (MAC_CSR_DATA) to
indirectly access the Host MAC CSR’s.
Note: The full list of Host MAC CSR’s are described in Section 14.3, "Host MAC Control and Status
Registers," on page 270. For more information on the Host MAC, refer to Chapter 9, "Host
MAC," on page 112.
BITS
DESCRIPTION
TYPE
DEFAULT
31
CSR Busy
When a 1 is written into this bit, the read or write operation is performed to
the specified Host MAC CSR. This bit will remain set until the operation is
complete. In the case of a read, this indicates that the host can read valid
data from the Host MAC CSR Interface Data Register (MAC_CSR_DATA).
R/W
SC
0b
R/W
0b
Note:
30
The MAC_CSR_CMD and MAC_CSR_DATA registers must not be
modified until this bit is cleared.
R/nW
When set, this bit indicates that the host is requesting a read operation.
When clear, the host is performing a write.
0: Host MAC CSR Write Operation
1: Host MAC CSR Read Operation
29:8
RESERVED
RO
-
7:0
CSR Address
The 8-bit value in this field selects which Host MAC CSR will be accessed
by the read or write operation. The index of each Host MAC CSR is defined
in Section 14.3, "Host MAC Control and Status Registers," on page 270.
R/W
00h
SMSC LAN9312
187
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.2.8
Host MAC CSR Interface Data Register (MAC_CSR_DATA)
Offset:
0A8h
Size:
32 bits
This read-write register is used in conjunction with the Host MAC CSR Interface Command Register
(MAC_CSR_CMD) to indirectly access the Host MAC CSR’s.
Note: The full list of Host MAC CSR’s are described in Section 14.3, "Host MAC Control and Status
Registers," on page 270. For more information on the Host MAC, refer to Chapter 9, "Host
MAC," on page 112.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Host MAC CSR Data
This field contains the value read from or written to the Host MAC CSR as
specified in the Host MAC CSR Interface Command Register
(MAC_CSR_CMD). Upon a read, the value returned depends on the R/nW
bit in the MAC_CSR_CMD register. If R/nW is a 1, the data in this register
is from the Host MAC. If R/nW is 0, the data is the value that was last written
into this register.
R/W
00000000h
Note:
The MAC_CSR_CMD and MAC_CSR_DATA registers must not be
modified until the CSR Busy bit is cleared in the MAC_CSR_CMD
register.
Revision 2.0 (02-14-13)
188
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.2.9
Host MAC Automatic Flow Control Configuration Register (AFC_CFG)
Offset:
0ACh
Size:
32 bits
This read/write register configures the mechanism that controls the automatic and software-initiated
transmission of pause frames and back pressure from the Host MAC to the switch fabric. This register
is used in conjunction with the Host MAC Flow Control Register (HMAC_FLOW) in the Host MAC CSR
space. Pause frames and backpressure are sent to the switch fabric to stop it from sending packets
to the Host MAC. Network data into the switch fabric is affected only if the switch fabric buffering fills.
Note: The Host MAC will not transmit pause frames or assert back pressure if the transmitter is
disabled. This register controls only the Host MAC flow control and not the Switch Engine
MAC’s flow control.
Refer to section Section 9.2, "Flow Control" for additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:24
RESERVED
RO
-
23:16
Automatic Flow Control High Level (AFC_HI)
This field specifies, in multiples of 64 bytes, the level at which flow control
will trigger. When this limit is reached, the chip will apply back pressure or
will transmit a pause frame as programmed in bits [3:0] of this register.
R/W
00h
R/W
00h
R/W
0h
During full-duplex operation only a single pause frame is transmitted when
this level is reached. The pause time transmitted in this frame is
programmed in the FCPT field of the Host MAC Flow Control Register
(HMAC_FLOW) in the Host MAC CSR space.
During half-duplex operation each incoming frame that matches the criteria
in bits [3:0] of this register will be jammed for the period set in the
BACK_DUR field.
Note:
15:8
7:4
This level is also used for hard-wired flow control when
HW_FC_EN is set in the Port 0(Host MAC) Manual Flow Control
Register (MANUAL_FC_MII).
Automatic Flow Control Low Level (AFC_LO)
This field specifies, in multiples of 64 bytes, the level at which a pause frame
is transmitted with a pause time setting of zero. When the amount of data
in the RX Data FIFO falls below this level the pause frame is transmitted. A
pause time value of zero instructs the other transmitting device to
immediately resume transmission. The zero time pause frame will only be
transmitted if the RX Data FIFO had reached the AFC_HI level and a pause
frame was sent. A zero pause time frame is sent whenever automatic flow
control in enabled in bits [3:0] of this register.
Note:
When automatic flow control is enabled the AFC_LO setting must
always be less than the AFC_HI setting.
Note:
This level is also used for hard-wired flow control when
HW_FC_EN is set in the Port 0(Host MAC) Manual Flow Control
Register (MANUAL_FC_MII).
Backpressure Duration (BACK_DUR)
When the Host MAC automatically asserts back pressure, it will be asserted
for this period of time. In full-duplex mode, this field has no function and is
not used. Please refer to Table 14.2, describing Backpressure Duration bit
mapping for more information.
SMSC LAN9312
189
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
3
Flow Control on Multicast Frame (FCMULT)
When this bit is set, the Host MAC will assert back pressure when the AFC
level is reached and a multicast frame is received. This field has no function
in full-duplex mode.
R/W
0b
R/W
0b
R/W
0b
R/W
0b
0: Flow Control on Multicast Frame Disabled
1: Flow Control on Multicast Frame Enabled
2
Flow Control on Broadcast Frame (FCBRD)
When this bit is set, the Host MAC will assert back pressure when the AFC
level is reached and a broadcast frame is received. This field has no function
in full-duplex mode.
0: Flow Control on Broadcast Frame Disabled
1: Flow Control on Broadcast Frame Enabled
1
Flow Control on Address Decode (FCADD)
When this bit is set, the Host MAC will assert back pressure when the AFC
level is reached and a frame addressed to the Host MAC is received. This
field has no function in full-duplex mode.
0: Flow Control on Address Decode Disabled
1: Flow Control on Address Decode Enabled
0
Flow Control on Any Frame (FCANY)
When this bit is set, the Host MAC will assert back pressure, or transmit a
pause frame when the AFC level is reached and any frame is received.
Setting this bit enables full-duplex flow control when the Host MAC is
operating in full-duplex mode.
When this mode is enabled during half-duplex operation, the Flow Controller
does not decode the Host MAC address and will send a JAM upon receipt
of a valid preamble (i.e., immediately at the beginning of the next frame after
the RX Data FIFO level is reached).
When this mode is enabled during full-duplex operation, the Flow Controller
will immediately instruct the Host MAC to send a pause frame when the RX
Data FIFO level is reached. The MAC will queue the pause frame
transmission for the next available window.
Setting this bit overrides bits [3:1] of this register.
Table 14.2 Backpressure Duration Bit Mapping
BACKPRESSURE DURATION
[7:4]
100Mbs Mode
10Mbs Mode
0h
5uS
7.2uS
1h
10uS
12.2uS
2h
15uS
17.2uS
3h
25uS
27.2uS
4h
50uS
52.2uS
5h
100uS
102.2uS
6h
150uS
152.2uS
7h
200uS
202.2uS
Revision 2.0 (02-14-13)
190
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.2 Backpressure Duration Bit Mapping (continued)
BACKPRESSURE DURATION
SMSC LAN9312
8h
250uS
252.2uS
9h
300uS
302.2uS
Ah
350uS
352.2uS
Bh
400uS
402.2uS
Ch
450uS
452.2uS
Dh
500uS
502.2uS
Eh
550uS
552.2uS
Fh
600uS
602.2uS
191
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.3
GPIO/LED
This section details the General Purpose I/O (GPIO) and LED related System CSR’s.
14.2.3.1
General Purpose I/O Configuration Register (GPIO_CFG)
Offset:
1E0h
Size:
32 bits
This read/write register configures the GPIO input and output pins. The polarity of the 12 GPIO pins
is configured here as well as the IEEE 1588 timestamping and clock compare event output properties
of the GPIO[9:8] pins.
BITS
DESCRIPTION
TYPE
DEFAULT
31:30
RESERVED
RO
-
29:28
GPIO 1588 Timer Interrupt Clear Enable 9-8
(GPIO_1588_TIMER_INT_CLEAR_EN[9:8])
These bits enable inputs on GPIO9 and GPIO8 to clear the
1588_TIMER_INT bit of the 1588 Interrupt Status and Enable Register
(1588_INT_STS_EN). The polarity of these inputs is determined by
GPIO_INT_POL[9:8].
R/W
00b
R/W
0h
R/W
0h
R/W
1b
Note:
27:16
The GPIO must be configured as an input for this function to
operate. For the clear function, GPIO inputs are edge sensitive and
must be active for greater than 40 nS to be recognized.
GPIO Interrupt Polarity 11-0 (GPIO_INT_POL[11:0])
These bits set the interrupt polarity of the 12 GPIO pins. The configured
level (high/low) will set the corresponding GPIO_INT bit in the General
Purpose I/O Interrupt Status and Enable Register (GPIO_INT_STS_EN).
0: Sets low logic level trigger on corresponding GPIO pin
1: Sets high logic level trigger on corresponding GPIO pin
GPIO_INT_POL[9:8] also determines the polarity of the GPIO IEEE 1588
time clock capture events and the GPIO 1588 Timer Interrupt Clear inputs.
Refer to Section 13.2, "GPIO Operation," on page 162 for additional
information.
15:14
1588 GPIO Output Enable 9-8 (1588_GPIO_OE[9:8])
These bits configure GPIO 9 and GPIO 8 to output 1588 clock compare
events.
0: Disables the output of 1588 clock compare events
1: Enables the output of 1588 clock compare events
Note:
13
These bits override the direction bits in the General Purpose I/O
Data & Direction Register (GPIO_DATA_DIR) register. However,
the GPIO buffer type (GPIOBUF[11:0]) in the General Purpose I/O
Configuration Register (GPIO_CFG) is not overridden.
GPIO 9 Clock Event Polarity (GPIO_EVENT_POL_9)
This bit determines if the 1588 clock event output on GPIO 9 is active high
or low.
0: 1588 clock event output active low
1: 1588 clock event output active high
Revision 2.0 (02-14-13)
192
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
12
GPIO 8 Clock Event Polarity (GPIO_EVENT_POL_8)
This bit determines if the 1588 clock event output on GPIO 8 is active high
or low.
R/W
1b
R/W
0h
0: 1588 clock event output active low
1: 1588 clock event output active high
11:0
GPIO Buffer Type 11-0 (GPIOBUF[11:0])
This field sets the buffer types of the 12 GPIO pins.
0: Corresponding GPIO pin configured as an open-drain driver
1: Corresponding GPIO pin configured as a push/pull driver
As an open-drain driver, the output pin is driven low when the corresponding
data register is cleared, and is not driven when the corresponding data
register is set.
As an open-drain driver used for 1588 Clock Events, the corresponding
GPIO_EVENT_POL_8 and GPIO_EVENT_POL_9 bits determine when the
corresponding pin is driven per the following table:
SMSC LAN9312
GPIOx Clock Event Polarity
1588 Clock Event
Pin State
0
no
not driven
0
yes
driven low
1
no
driven low
1
yes
not driven
193
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.3.2
General Purpose I/O Data & Direction Register (GPIO_DATA_DIR)
Offset:
1E4h
Size:
32 bits
This read/write register configures the direction of the 12 GPIO pins and contains the GPIO input and
output data bits.
BITS
DESCRIPTION
TYPE
DEFAULT
31:28
RESERVED
RO
-
27:16
GPIO Direction 11-0 (GPIODIR[11:0])
These bits set the input/output direction of the 12 GPIO pins.
R/W
0h
RESERVED
RO
-
GPIO Data 11-0 (GPIOD[11:0])
When a GPIO pin is enabled as an output, the value written to this field is
output on the corresponding GPIO pin. Upon a read, the value returned
depends on the current direction of the pin. If the pin is an input, the data
reflects the current state of the corresponding GPIO pin. If the pin is an
output, the data is the value that was last written into this register. For
GPIOs 11-10 and 7-0, the pin direction is determined by the GPDIR bits of
this register. For GPIOs 9 and 8, the pin direction is determined by the
GPDIR bits and the 1588_GPIO_OE bits in the General Purpose I/O
Configuration Register (GPIO_CFG).
R/W
0h
0: GPIO pin is configured as an input
1: GPIO pin is configured as an output
15:12
11:0
Revision 2.0 (02-14-13)
194
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.3.3
General Purpose I/O Interrupt Status and Enable Register (GPIO_INT_STS_EN)
Offset:
1E8h
Size:
32 bits
This read/write register contains the GPIO interrupt status bits.
Writing a 1 to any of the interrupt status bits acknowledges and clears the interrupt. If enabled, these
interrupt bits are cascaded into bit 12 (GPIO) of the Interrupt Status Register (INT_STS). Writing a 1
to any of the interrupt enable bits will enable the corresponding interrupt as a source. Status bits will
still reflect the status of the interrupt source regardless of whether the source is enabled as an interrupt
in this register. Bit 12 (GPIO_EN) of the Interrupt Enable Register (INT_EN) must also be set in order
for an actual system level interrupt to occur. Refer to Chapter 5, "System Interrupts," on page 49 for
additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:28
RESERVED
RO
-
27:16
GPIO Interrupt Enable[11:0] (GPIO[11:0]_INT_EN)
When set, these bits enable the corresponding GPIO interrupt.
R/W
0h
RO
-
R/WC
0h
Note:
15:12
11:0
The GPIO interrupts must also be enabled via bit 12 (GPIO_EN) of
the Interrupt Enable Register (INT_EN) in order to cause the
interrupt pin (IRQ) to be asserted.
RESERVED
GPIO Interrupt[11:0] (GPIO[11:0]_INT)
These signals reflect the interrupt status as generated by the GPIOs. These
interrupts are configured through the General Purpose I/O Configuration
Register (GPIO_CFG).
Note:
SMSC LAN9312
As GPIO interrupts, GPIO inputs are level sensitive and must be
active greater than 40 nS to be recognized as interrupt inputs.
195
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.3.4
LED Configuration Register (LED_CFG)
Offset:
1BCh
Size:
32 bits
This read/write register configures the GPIO[7:0] pins as LED[7:0] pins and sets their functionality.
BITS
31:10
9:8
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
LED Function 1-0 (LED_FUN[1:0])
These bits control the function associated with each LED pin as shown in
Table 13.1 of Section 13.3, "LED Operation," on page 164.
R/W
Note 14.2
R/W
Note 14.3
Note:
7:0
In order for these assignments to be valid, the particular pin must
be enabled as an LED output pin via the LED_EN[7:0] bits of this
register.
LED Enable 7-0 (LED_EN[7:0])
This field toggles the functionality of the GPIO[7:0] pins between GPIO and
LED.
0: Enables the associated pin as a GPIO signal
1: Enables the associated pin as a LED output
Note 14.2 The default value of this field is determined by the configuration strap LED_fun_strap[1:0].
Configuration strap values are latched on power-on reset or nRST de-assertion. Some
configuration straps can be overridden by values from the EEPROM Loader. Refer to
Section 4.2.4, "Configuration Straps," on page 40 for more information.
Note 14.3 The default value of this field is determined by the configuration strap LED_en_strap[7:0].
Configuration strap values are latched on power-on reset or nRST de-assertion. Some
configuration straps can be overridden by values from the EEPROM Loader. Refer to
Section 4.2.4, "Configuration Straps," on page 40 for more information.
Revision 2.0 (02-14-13)
196
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.4
EEPROM
This section details the EEPROM related System CSR’s. These registers should only be used if an
EEPROM has been connected to the LAN9312. Refer to chapter Section 10.2, "I2C/Microwire Master
EEPROM Controller," on page 137 for additional information on the various modes (I2C and Microwire)
of the EEPROM Controller (EPC).
14.2.4.1
EEPROM Command Register (E2P_CMD)
Offset:
1B4h
Size:
32 bits
This read/write register is used to control the read and write operations of the serial EEPROM.
BITS
DESCRIPTION
TYPE
DEFAULT
31
EEPROM Controller Busy (EPC_BUSY)
When a 1 is written into this bit, the operation specified in the
EPC_COMMAND field of this register is performed at the specified
EEPROM address. This bit will remain set until the selected operation is
complete. In the case of a read, this indicates that the Host can read valid
data from the EEPROM Data Register (E2P_DATA). The E2P_CMD and
E2P_DATA registers should not be modified until this bit is cleared. In the
case where a write is attempted and an EEPROM is not present, the
EPC_BUSY bit remains set until the EEPROM Controller Timeout
(EPC_TIMEOUT) bit is set. At this time the EPC_BUSY bit is cleared.
R/W
SC
0b
Note:
SMSC LAN9312
EPC_BUSY is set immediately following power-up, or pin reset, or
DIGITAL_RST reset. This bit is also set following the settings of the
SRST bit in the Hardware Configuration Register (HW_CFG). After
the EEPROM Loader has finished loading, the EPC_BUSY bit is
cleared. Refer to chapter Section 10.2.4, "EEPROM Loader," on
page 149 for more information.
197
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
30:28
EEPROM Controller Command (EPC_COMMAND)
This field is used to issue commands to the EEPROM controller. The
EEPROM controller will execute a command when the EPC_BUSY bit is set.
A new command must not be issued until the previous command completes.
The field is encoded as follows:
R/W
000b
RO
-
Note:
[30]
[29]
[28]
0
0
0
Operation
READ
0
0
1
EWDS
0
1
0
EWEN
0
1
1
WRITE
1
0
0
WRAL
1
0
1
ERASE
1
1
0
ERAL
1
1
1
RELOAD
Only the READ, WRITE and RELOAD commands are valid for I2C mode.
If an unsupported command is attempted, the EPC_BUSY bit will be
cleared and EPC_TIMEOUT will be set.
The EEPROM operations are defined as follows:
READ (Read Location)
This command will cause a read of the EEPROM location pointed to by the
EPC_ADDRESS bit field. The result of the read is available in the EEPROM Data
Register (E2P_DATA).
EWDS (Erase/Write Disable)
(Microwire mode only) - When this command is issued, the EEPROM will ignore erase
and write commands. To re-enable erase/writes operations, issue the EWEN
command.
EWEN (Erase/Write Enable)
(Microwire mode only) - Enables the EEPROM for erase and write operations. The
EEPROM will allow erase and write operations until the EWDS command is sent, or
until the power is cycled. The Microwire EEPROM device will power-up in the
erase/write disabled state. Any erase or write operations will fail until an EWEN
command is issued.
WRITE (Write Location)
If erase/write operations are enabled in the EEPROM, this command will cause the
contents of the EEPROM Data Register (E2P_DATA) to be written to the EEPROM
location selected by the EPC_ADDRESS field. For Microwire, erase/write operations
must be enabled in the EEPROM.
WRAL (Write All)
(Microwire mode only) - If erase/write operations are enabled in the EEPROM, this
command will cause the contents of the EEPROM Data Register (E2P_DATA) to be
written to every EEPROM memory location.
ERASE (Erase Location)
(Microwire mode only) - If erase/write operations are enabled in the EEPROM, this
command will erase the location selected by the EPC_ADDRESS field.
ERAL (Erase All)
(Microwire mode only) - If erase/write operations are enabled in the EEPROM, this
command will initiate a bulk erase of the entire EEPROM.
RELOAD (EEPROM Loader Reload)
Instructs the EEPROM Loader to reload the device from the EEPROM. If a value of
A5h is not found in the first address of the EEPROM, the EEPROM is assumed to be
un-programmed and the RELOAD operation will fail. The CFG_LOADED bit indicates
a successful load. Following this command, the device will enter the not ready state.
The READY bit in the Hardware Configuration Register (HW_CFG) should be polled
to determine then the RELOAD is complete.
27:19
RESERVED
Revision 2.0 (02-14-13)
198
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
18
EEPROM Loader Address Overflow (LOADER_OVERFLOW)
This bit indicates that the EEPROM Loader tried to read past the end of the
EEPROM address space. This indicates misconfigured EEPROM data.
RO
0b
R/WC
0b
R/WC
0b
R/W
0000h
This bit is cleared when the EEPROM Loader is restarted with a RELOAD
command, Soft Reset(SRST), or a Digital Reset(DIGITAL_RST).
17
EEPROM Controller Timeout (EPC_TIMEOUT)
This bit is set when a timeout occurs, indicating the last operation was
unsuccessful. If an EEPROM ERASE, ERAL, WRITE or WRAL operation is
performed and no response is received from the EEPROM within 30mS, the
EEPROM controller will timeout and return to its idle state.
For the I2C mode, the bit is also set if the EEPROM fails to respond with
the appropriate ACKs, if the EEPROM slave device holds the clock low for
more than 30ms, or if an unsupported EPC_COMMAND is attempted.
This bit is cleared when written high.
Note:
16
When in Microwire mode, if an EEPROM device is not connected,
an internal pull-down on the EEDI pin will keep the EEDI signal low
and allow timeouts to occur. If EEDI is pulled high externally, EPC
commands will not time out if an EEPROM device is not connected.
In this case the EPC_BUSY bit will be cleared as soon as the
command sequence is complete. It should also be noted that the
ERASE, ERAL, WRITE and WRAL commands are the only EPC
commands that will timeout if an EEPROM device is not present
AND the EEDI signal is pulled low.
Configuration Loaded (CFG_LOADED)
When set, this bit indicates that a valid EEPROM was found and the
EEPROM Loader completed normally. This bit is set upon a successful load.
It is cleared on power-up, pin and DIGITAL_RST resets, Soft Reset(SRST),
or at the start of a RELOAD.
This bit is cleared when written high.
15:0
EEPROM Controller Address (EPC_ADDRESS)
This field is used by the EEPROM Controller to address a specific memory
location in the serial EEPROM. This address must be byte aligned.
SMSC LAN9312
199
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.4.2
EEPROM Data Register (E2P_DATA)
Offset:
1B8h
Size:
32 bits
This read/write register is used in conjunction with the EEPROM Command Register (E2P_CMD) to
perform read and write operations with the serial EEPROM.
BITS
DESCRIPTION
TYPE
DEFAULT
31:8
RESERVED
RO
-
7:0
EEPROM Data (EEPROM_DATA)
This field contains the data read from or written to the EEPROM.
R/W
00h
Revision 2.0 (02-14-13)
200
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5
IEEE 1588
This section details the IEEE 1588 timestamp related registers. Each port of the LAN9312 has a 1588
timestamp block with 8 related registers, 4 for transmit capture and 4 for receive capture. These sets
of registers are identical in functionality for each port, and thus their register descriptions have been
consolidated. In these cases, the register names will be amended with a lowercase “x” in place of the
port designation. The wildcard “x” should be replaced with “1”, “2”, or “MII” for the Port 1, Port 2, and
Port 0(Host MAC) respectively. A list of all the 1588 related registers can be seen in Table 14.1. For
more information on the IEEE 1588, refer to Chapter 11, "IEEE 1588 Hardware Time Stamp Unit," on
page 154.
14.2.5.1
Port x 1588 Clock High-DWORD Receive Capture Register (1588_CLOCK_HI_RX_CAPTURE_x)
Offset:
Port 1: 100h
Port 2: 120h
Port 0: 140h
Size:
32 bits
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Timestamp High (TS_HI)
This field contains the high 32-bits of the timestamp taken on the receipt of
a 1588 Sync or Delay_Req packet.
RO
00000000h
Note: The selection between Sync or Delay_Req packets is based on the corresponding
master/slave bit in the 1588 Configuration Register (1588_CONFIG).
Note: There are multiple instantiations of this register, one for each port of the LAN9312. Refer to
Section 14.2.5 for additional information.
Note: For Port 0(Host MAC), receive is defined as data from the switch fabric, while transmit is to
the switch fabric.
SMSC LAN9312
201
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.2
Port x 1588 Clock Low-DWORD Receive Capture Register (1588_CLOCK_LO_RX_CAPTURE_x)
Offset:
Port 1: 104h
Port 2: 124h
Port 0: 144h
Size:
32 bits
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Timestamp Low (TS_LO)
This field contains the low 32-bits of the timestamp taken on the receipt of
a 1588 Sync or Delay_Req packet.
RO
00000000h
Note: The selection between Sync or Delay_Req packets is based on the corresponding
master/slave bit in the 1588 Configuration Register (1588_CONFIG).
Note: There are multiple instantiations of this register, one for each port of the LAN9312. Refer to
Section 14.2.5 for additional information.
Note: For Port 0(Host MAC), receive is defined as data from the switch fabric, while transmit is to
the switch fabric.
Revision 2.0 (02-14-13)
202
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.3
Port x 1588 Sequence ID, Source UUID High-WORD Receive Capture Register
(1588_SEQ_ID_SRC_UUID_HI_RX_CAPTURE_x)
Offset:
BITS
Port 1: 108h
Port 2: 128h
Port 0: 148h
Size:
32 bits
DESCRIPTION
TYPE
DEFAULT
31:16
Sequence ID (SEQ_ID)
This field contains the Sequence ID from the 1588 Sync or Delay_Req
packet.
RO
0000h
15:0
Source UUID High (SRC_UUID_HI)
This field contains the high 16-bits of the Source UUID from the 1588 Sync
or Delay_Req packet.
RO
0000h
Note: The selection between Sync or Delay_Req packets is based on the corresponding
master/slave bit in the 1588 Configuration Register (1588_CONFIG).
Note: There are multiple instantiations of this register, one for each port of the LAN9312. Refer to
Section 14.2.5 for additional information.
Note: For Port 0(Host MAC), receive is defined as data from the switch fabric, while transmit is to
the switch fabric.
SMSC LAN9312
203
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.4
Port x 1588 Source UUID Low-DWORD Receive Capture Register
(1588_SRC_UUID_LO_RX_CAPTURE_x)
Offset:
Port 1: 10Ch
Port 2: 12Ch
Port 0: 14Ch
Size:
32 bits
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Source UUID Low (SRC_UUID_LO)
This field contains the low 32-bits of the Source UUID from the 1588 Sync
or Delay_Req packet.
RO
00000000h
Note: The selection between Sync or Delay_Req packets is based on the corresponding
master/slave bit in the 1588 Configuration Register (1588_CONFIG).
Note: There are multiple instantiations of this register, one for each port of the LAN9312. Refer to
Section 14.2.5 for additional information.
Note: For Port 0(Host MAC), receive is defined as data from the switch fabric, while transmit is to
the switch fabric.
Revision 2.0 (02-14-13)
204
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.5
Port x 1588 Clock High-DWORD Transmit Capture Register (1588_CLOCK_HI_TX_CAPTURE_x)
Offset:
BITS
31:0
Port 1: 110h
Port 2: 130h
Port 0: 150h
Size:
DESCRIPTION
Timestamp High (TS_HI)
This field contains the high 32-bits of the timestamp taken on the
transmission of a 1588 Sync or Delay_Req packet.
32 bits
TYPE
DEFAULT
RO
00000000h
Note: The selection between Sync or Delay_Req packets is based on the corresponding
master/slave bit in the 1588 Configuration Register (1588_CONFIG).
Note: There are multiple instantiations of this register, one for each port of the LAN9312. Refer to
Section 14.2.5 for additional information.
Note: For Port 0(Host MAC), receive is defined as data from the switch fabric, while transmit is to
the switch fabric.
SMSC LAN9312
205
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.6
Port x 1588 Clock Low-DWORD Transmit Capture Register (1588_CLOCK_LO_TX_CAPTURE_x)
Offset:
BITS
31:0
Port 1: 114h
Port 2: 134h
Port 0: 154h
Size:
DESCRIPTION
Timestamp Low (TS_LO)
This field contains the low 32-bits of the timestamp taken on the
transmission of a 1588 Sync or Delay_Req packet.
32 bits
TYPE
DEFAULT
RO
00000000h
Note: The selection between Sync or Delay_Req packets is based on the corresponding
master/slave bit in the 1588 Configuration Register (1588_CONFIG).
Note: There are multiple instantiations of this register, one for each port of the LAN9312. Refer to
Section 14.2.5 for additional information.
Note: For Port 0(Host MAC), receive is defined as data from the switch fabric, while transmit is to
the switch fabric.
Revision 2.0 (02-14-13)
206
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.7
Port x 1588 Sequence ID, Source UUID High-WORD Transmit Capture Register
(1588_SEQ_ID_SRC_UUID_HI_TX_CAPTURE_x)
Offset:
BITS
Port 1: 118h
Port 2: 138h
Port 0: 158h
Size:
32 bits
DESCRIPTION
TYPE
DEFAULT
31:16
Sequence ID (SEQ_ID)
This field contains the Sequence ID from the 1588 Sync or Delay_Req
packet.
RO
0000h
15:0
Source UUID High (SRC_UUID_HI)
This field contains the high 16-bits of the Source UUID from the 1588 Sync
or Delay_Req packet.
RO
0000h
Note: The selection between Sync or Delay_Req packets is based on the corresponding
master/slave bit in the 1588 Configuration Register (1588_CONFIG).
Note: There are multiple instantiations of this register, one for each port of the LAN9312. Refer to
Section 14.2.5 for additional information.
Note: For Port 0(Host MAC), receive is defined as data from the switch fabric, while transmit is to
the switch fabric.
SMSC LAN9312
207
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.8
Port x 1588 Source UUID Low-DWORD Transmit Capture Register
(1588_SRC_UUID_LO_TX_CAPTURE_x)
Offset:
Port 1: 11Ch
Port 2: 13Ch
Port 0: 15Ch
Size:
32 bits
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Source UUID Low (SRC_UUID_TX_LO)
This field contains the low 32-bits of the Source UUID from the 1588 Sync
or Delay_Req packet.
RO
00000000h
Note: The selection between Sync or Delay_Req packets is based on the corresponding
master/slave bit in the 1588 Configuration Register (1588_CONFIG).
Note: There are multiple instantiations of this register, one for each port of the LAN9312. Refer to
Section 14.2.5 for additional information.
Note: For Port 0(Host MAC), receive is defined as data from the switch fabric, while transmit is to
the switch fabric.
Revision 2.0 (02-14-13)
208
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.9
GPIO 8 1588 Clock High-DWORD Capture Register (1588_CLOCK_HI_CAPTURE_GPIO_8)
Offset:
160h
Size:
32 bits
This read only register combined with the GPIO 8 1588 Clock Low-DWORD Capture Register
(1588_CLOCK_LO_CAPTURE_GPIO_8) form the 64-bit GPIO 8 timestamp capture.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Timestamp High (TS_HI)
This field contains the high 32-bits of the timestamp upon activation of GPIO
8.
RO
00000000h
SMSC LAN9312
209
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.10
GPIO 8 1588 Clock Low-DWORD Capture Register (1588_CLOCK_LO_CAPTURE_GPIO_8)
Offset:
164h
Size:
32 bits
This read only register combined with the GPIO 8 1588 Clock High-DWORD Capture Register
(1588_CLOCK_HI_CAPTURE_GPIO_8) form the 64-bit GPIO 8 timestamp capture.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Timestamp Low (TS_LO)
This field contains the low 32-bits of the timestamp upon activation of GPIO
8.
RO
00000000h
Revision 2.0 (02-14-13)
210
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.11
GPIO 9 1588 Clock High-DWORD Capture Register (1588_CLOCK_HI_CAPTURE_GPIO_9)
Offset:
168h
Size:
32 bits
This read only register combined with the GPIO 9 1588 Clock Low-DWORD Capture Register
(1588_CLOCK_LO_CAPTURE_GPIO_9) form the 64-bit GPIO 9 timestamp capture.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Timestamp High (TS_HI)
This field contains the high 32-bits of the timestamp upon activation of GPIO
9.
RO
00000000h
SMSC LAN9312
211
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.12
GPIO 9 1588 Clock Low-DWORD Capture Register (1588_CLOCK_LO_CAPTURE_GPIO_9)
Offset:
16Ch
Size:
32 bits
This read only register combined with the GPIO 9 1588 Clock High-DWORD Capture Register
(1588_CLOCK_HI_CAPTURE_GPIO_9) form the 64-bit GPIO 9 timestamp capture.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Timestamp Low (TS_LO)
This field contains the low 32-bits of the timestamp upon activation of GPIO
9.
RO
00000000h
Revision 2.0 (02-14-13)
212
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.13
1588 Clock High-DWORD Register (1588_CLOCK_HI)
Offset:
170h
Size:
32 bits
This read/write register combined with 1588 Clock Low-DWORD Register (1588_CLOCK_LO) form the
64-bit 1588 Clock value. The 1588 Clock value is used for all 1588 timestamping. The 1588 Clock has
a base frequency of 100MHz, which can be adjusted via the 1588 Clock Addend Register
(1588_CLOCK_ADDEND) accordingly. Refer to Chapter 11, "IEEE 1588 Hardware Time Stamp Unit,"
on page 154 for additional information.
BITS
31:0
DESCRIPTION
Clock High (CLOCK_HI)
This field contains the high 32-bits of the 64-bit 1588 Clock.
TYPE
DEFAULT
R/W
00000000h
Note: Both this register and the 1588 Clock Low-DWORD Register (1588_CLOCK_LO) must be
written for either to be affected.
Note: The value read is the saved value of the 1588 Clock when the 1588_CLOCK_SNAPSHOT bit
in the 1588 Command Register (1588_CMD) is set.
SMSC LAN9312
213
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.14
1588 Clock Low-DWORD Register (1588_CLOCK_LO)
Offset:
174h
Size:
32 bits
This read/write register combined with 1588 Clock High-DWORD Register (1588_CLOCK_HI) form the
64-bit 1588 Clock value. The 1588 Clock value is used for all 1588 timestamping. The 1588 Clock has
a base frequency of 100MHz, which can be adjusted via the 1588 Clock Addend Register
(1588_CLOCK_ADDEND) accordingly. Refer to Chapter 11, "IEEE 1588 Hardware Time Stamp Unit,"
on page 154 for additional information.
BITS
31:0
DESCRIPTION
Clock Low (CLOCK_LO)
This field contains the low 32-bits of the 64-bit 1588 Clock.
TYPE
DEFAULT
R/W
00000000h
Note: Both this register and the 1588 Clock High-DWORD Register (1588_CLOCK_HI) must be
written for either to be affected.
Note: The value read is the saved value of the 1588 Clock when the 1588_CLOCK_SNAPSHOT bit
in the 1588 Command Register (1588_CMD) is set.
Revision 2.0 (02-14-13)
214
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.15
1588 Clock Addend Register (1588_CLOCK_ADDEND)
Offset:
178h
Size:
32 bits
This read/write register is responsible for adjusting the 64-bit 1588 Clock frequency. Refer to
Chapter 11, "IEEE 1588 Hardware Time Stamp Unit," on page 154 for details on how to properly use
this register.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Clock Addend (CLOCK_ADDEND)
This 32-bit value is added to the 1588 frequency divisor accumulator every
cycle. This allows the base 100MHz frequency of the 64-bit 1588 Clock to
be adjusted accordingly.
R/W
00000000h
SMSC LAN9312
215
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.16
1588 Clock Target High-DWORD Register (1588_CLOCK_TARGET_HI)
Offset:
17Ch
Size:
32 bits
T h i s r e a d / w r i t e r e g i s t e r c o m b i n e d w i t h 1 5 8 8 C l o c k Ta r g e t L o w - D W O R D R e g i s t e r
(1588_CLOCK_TARGET_LO) form the 64-bit 1588 Clock Target value. The 1588 Clock Target value
is compared to the current 1588 Clock value and can be used to trigger an interrupt upon at match.
Refer to Chapter 11, "IEEE 1588 Hardware Time Stamp Unit," on page 154 for additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Clock Target High (CLOCK_TARGET_HI)
This field contains the high 32-bits of the 64-bit 1588 Clock Compare value.
R/W
00000000h
Note: Both
this
register
and
the
1588
Clock
Target
Low-DWORD
(1588_CLOCK_TARGET_LO) must be written for either to be affected.
Revision 2.0 (02-14-13)
216
DATASHEET
Register
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.17
1588 Clock Target Low-DWORD Register (1588_CLOCK_TARGET_LO)
Offset:
180h
Size:
32 bits
T h i s r e a d / w r i t e r e g i s t e r c o m b i n e d w i t h 1 5 8 8 C l o c k Ta r g e t H i g h - D W O R D R e g i s t e r
(1588_CLOCK_TARGET_HI) form the 64-bit 1588 Clock Target value. The 1588 Clock Target value is
compared to the current 1588 Clock value and can be used to trigger an interrupt upon at match. Refer
to Chapter 11, "IEEE 1588 Hardware Time Stamp Unit," on page 154 for additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Clock Target Low (CLOCK_TARGET_LO)
This field contains the low 32-bits of the 64-bit 1588 Clock Compare value.
R/W
00000000h
Note: Both
this
register
and
the
1588
Clock
Target
High-DWORD
(1588_CLOCK_TARGET_HI) must be written for either to be affected.
SMSC LAN9312
217
DATASHEET
Register
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.18
1588 Clock Target Reload High-DWORD Register (1588_CLOCK_TARGET_RELOAD_HI)
Offset:
184h
Size:
32 bits
This read/write register combined with 1588 Clock Target Reload/Add Low-DWORD Register
(1588_CLOCK_TARGET_RELOAD_LO) form the 64-bit 1588 Clock Target Reload value. The 1588
Clock Target Reload is the value that is reloaded to the 1588 Clock Compare value when a clock
compare event occurs and the Reload/Add (RELOAD_ADD) bit of the 1588 Configuration Register
(1588_CONFIG) is set. Refer to Chapter 11, "IEEE 1588 Hardware Time Stamp Unit," on page 154 for
additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Clock Target Reload High (CLOCK_TARGET_RELOAD_HI)
This field contains the high 32-bits of the 64-bit 1588 Clock Target Reload
value that is reloaded to the 1588 Clock Compare value.
R/W
00000000h
Note: Both this register and the 1588 Clock Target Reload/Add Low-DWORD Register
(1588_CLOCK_TARGET_RELOAD_LO) must be written for either to be affected.
Revision 2.0 (02-14-13)
218
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.19
1588 Clock Target Reload/Add Low-DWORD Register (1588_CLOCK_TARGET_RELOAD_LO)
Offset:
188h
Size:
32 bits
This read/write register combined with 1588 Clock Target Reload High-DWORD Register
(1588_CLOCK_TARGET_RELOAD_HI) form the 64-bit 1588 Clock Target Reload value. The 1588
Clock Target Reload is the value that is reloaded or added to the 1588 Clock Compare value when a
clock compare event occurs. Whether this value is reloaded or added is determined by the Reload/Add
(RELOAD_ADD) bit of the 1588 Configuration Register (1588_CONFIG). Refer to Chapter 11, "IEEE
1588 Hardware Time Stamp Unit," on page 154 for additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Clock Target Reload Low (CLOCK_TARGET_RELOAD_LO)
This field contains the low 32-bits of the 64-bit 1588 Clock Target Reload
value that is reloaded to the 1588 Clock Compare value. Alternatively, these
32-bits are added to the 1588 Clock Compare value when configured
accordingly.
R/W
00000000h
Note: Both this register and the 1588 Clock Target Reload High-DWORD
(1588_CLOCK_TARGET_RELOAD_HI) must be written for either to be affected.
SMSC LAN9312
219
DATASHEET
Register
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.20
1588 Auxiliary MAC Address High-WORD Register (1588_AUX_MAC_HI)
Offset:
18Ch
Size:
32 bits
This read/write register combined with the 1588 Auxiliary MAC Address Low-DWORD Register
(1588_AUX_MAC_LO) forms the 48-bit Auxiliary (user defined) MAC address. The Auxiliary MAC
address can be enabled for each port of the LAN9312 via their respective User Defined MAC Address
Enable bit in the 1588 Configuration Register (1588_CONFIG). Refer to Chapter 11, "IEEE 1588
Hardware Time Stamp Unit," on page 154 for additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:0
Auxiliary MAC Address High (AUX_MAC_HI)
This field contains the high 16-bits of the Auxiliary MAC address used for
PTP packet detection.
R/W
0000h
Revision 2.0 (02-14-13)
220
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.21
1588 Auxiliary MAC Address Low-DWORD Register (1588_AUX_MAC_LO)
Offset:
190h
Size:
32 bits
This read/write register combined with the 1588 Auxiliary MAC Address High-WORD Register
(1588_AUX_MAC_HI) forms the 48-bit Auxiliary (user defined) MAC address. The Auxiliary MAC
address can be enabled for each port of the LAN9312 via their respective User Defined MAC Address
Enable bit in the 1588 Configuration Register (1588_CONFIG). Refer to Chapter 11, "IEEE 1588
Hardware Time Stamp Unit," on page 154 for additional information.
BITS
31:0
DESCRIPTION
Auxiliary MAC Address Low (AUX_MAC_LO)
This field contains the low 32-bits of the Auxiliary MAC address used for
PTP packet detection.
SMSC LAN9312
221
DATASHEET
TYPE
DEFAULT
R/W
00000000h
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.22
1588 Configuration Register (1588_CONFIG)
Offset:
194h
Size:
32 bits
This read/write register is responsible for the configuration of the 1588 timestamps for all ports.
BITS
DESCRIPTION
TYPE
DEFAULT
31
Master/Slave Port 2 (M_nS_2)
When set, Port 2 is a time clock master and captures timestamps when a
Sync packet is transmitted and when a Delay_Req is received. When
cleared, Port 2 is a time clock slave and captures timestamps when a
Delay_Req packet is transmitted and when a Sync packet is received.
R/W
0b
30
Primary MAC Address Enable Port 2 (MAC_PRI_EN_2)
This bit enables/disables the primary MAC address on Port 2.
R/W
1b
R/W
0b
R/W
0b
R/W
0b
R/W
0b
R/W
1b
R/W
1b
0: Disables primary MAC address on Port 2
1: Enables MAC address 01:00:5E:00:01:81 as a PTP address on Port 2
29
Alternate MAC Address 1 Enable Port 2 (MAC_ALT1_EN_2)
This bit enables/disables the alternate MAC address 1 on Port 2.
0: Disables alternate MAC address on Port 2
1: Enables MAC address 01:00:5E:00:01:82 as a PTP address on Port 2
28
Alternate MAC Address 2 Enable Port 2 (MAC_ALT2_EN_2)
This bit enables/disables the alternate MAC address 2 on Port 2.
0: Disables alternate MAC address on Port 2
1: Enables MAC address 01:00:5E:00:01:83 as a PTP address on Port 2
27
Alternate MAC Address 3 Enable Port 2 (MAC_ALT3_EN_2)
This bit enables/disables the alternate MAC address 3 on Port 2.
0: Disables alternate MAC address on Port 2
1: Enables MAC address 01:00:5E:00:01:84 as a PTP address on Port 2
26
User Defined MAC Address Enable Port 2 (MAC_USER_EN_2)
This bit enables/disables the auxiliary MAC address on Port 2. The auxiliary
address is defined via the 1588_AUX_MAC_HI and 1588_AUX_MAC_LO
registers.
0: Disables auxiliary MAC address on Port 2
1: Enables auxiliary MAC address as a PTP address on Port 2
25
Lock Enable RX Port 2 (LOCK_RX_2)
This bit enables/disables the RX lock. This lock prevents a 1588 capture
from overwriting the Clock, UUDI and Sequence ID values if the 1588 RX
interrupt for Port 2 is already set due to a previous capture.
0: Disables RX Port 2 Lock
1: Enables RX Port 2 Lock
24
Lock Enable TX Port 2 (LOCK_TX_2)
This bit enables/disables the TX lock. This lock prevents a 1588 capture
from overwriting the Clock, UUDI and Sequence ID values if the 1588 TX
interrupt for Port 2 is already set due to a previous capture.
0: Disables TX Port 2 Lock
1: Enables TX Port 2 Lock
Revision 2.0 (02-14-13)
222
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
23
Master/Slave Port 1 (M_nS_1)
When set, Port 1 is a time clock master and captures timestamps when a
Sync packet is transmitted and when a Delay_Req is received. When
cleared, Port 1 is a time clock slave and captures timestamps when a
Delay_Req packet is transmitted and when a Sync packet is received.
R/W
0b
22
Primary MAC Address Enable Port 1 (MAC_PRI_EN_1)
This bit enables/disables the primary MAC address on Port 1.
R/W
1b
R/W
0b
R/W
0b
R/W
0b
R/W
0b
R/W
1b
R/W
1b
R/W
0b
R/W
1b
0: Disables primary MAC address on Port 1
1: Enables MAC address 01:00:5E:00:01:81 as a PTP address on Port 1
21
Alternate MAC Address 1 Enable Port 1 (MAC_ALT1_EN_1)
This bit enables/disables the alternate MAC address 1 on Port 1.
0: Disables alternate MAC address on Port 1
1: Enables MAC address 01:00:5E:00:01:82 as a PTP address on Port 1
20
Alternate MAC Address 2 Enable Port 1 (MAC_ALT2_EN_1)
This bit enables/disables the alternate MAC address 2 on Port 1.
0: Disables alternate MAC address on Port 1
1: Enables MAC address 01:00:5E:00:01:83 as a PTP address on Port 1
19
Alternate MAC Address 3 Enable Port 1 (MAC_ALT3_EN_1)
This bit enables/disables the alternate MAC address 3 on Port 1.
0: Disables alternate MAC address on Port 1
1: Enables MAC address 01:00:5E:00:01:84 as a PTP address on Port 1
18
User Defined MAC Address Enable Port 1 (MAC_USER_EN_1)
This bit enables/disables the auxiliary MAC address on Port 1. The auxiliary
address is defined via the 1588_AUX_MAC_HI and 1588_AUX_MAC_LO
registers.
0: Disables auxiliary MAC address on Port 1
1: Enables auxiliary MAC address as a PTP address on Port 1
17
Lock Enable RX Port 1 (LOCK_RX_1)
This bit enables/disables the RX lock. This lock prevents a 1588 capture
from overwriting the Clock, UUDI and Sequence ID values if the 1588 RX
interrupt for Port 1 is ready set due to a previous capture.
0: Disables RX Port 1 Lock
1: Enables RX Port 1 Lock
16
Lock Enable TX Port 1 (LOCK_TX_1)
This bit enables/disables the TX lock. This lock prevents a 1588 capture
from overwriting the Clock, UUDI and Sequence ID values if the 1588 TX
interrupt for Port 1 is ready set due to a previous capture.
0: Disables TX Port 1 Lock
1: Enables TX Port 1 Lock
15
Master/Slave Port 0(Host MAC)(M_nS_MII)
When set, Port 0 is a time clock master and captures timestamps when a
Sync packet is transmitted and when a Delay_Req is received. When
cleared, Port 0 is a time clock slave and captures timestamps when a
Delay_Req packet is transmitted and when a Sync packet is received.
Note:
14
For Port 0, receive is defined as data from the switch fabric, while
transmit is defined as data to the switch fabric.
Primary MAC Address Enable Port 0(Host MAC) (MAC_PRI_EN_MII)
This bit enables/disables the primary MAC address on Port 0.
0: Disables primary MAC address on Port 0
1: Enables MAC address 01:00:5E:00:01:81 as a PTP address on Port 0
SMSC LAN9312
223
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
13
DESCRIPTION
Alternate MAC Address 1 Enable Port 0(Host MAC)
(MAC_ALT1_EN_MII)
This bit enables/disables the alternate MAC address 1 on Port 0.
TYPE
DEFAULT
R/W
0b
R/W
0b
R/W
0b
R/W
0b
R/W
1b
R/W
1b
0: Disables alternate MAC address on Port 0
1: Enables MAC address 01:00:5E:00:01:82 as a PTP address on Port 0
12
Alternate MAC Address 2 Enable Port 0(Host MAC)
(MAC_ALT2_EN_MII)
This bit enables/disables the alternate MAC address 2 on Port 0.
0: Disables alternate MAC address on Port 0
1: Enables MAC address 01:00:5E:00:01:83 as a PTP address on Port 0
11
Alternate MAC Address 3 Enable Port 0(Host MAC)
(MAC_ALT3_EN_MII)
This bit enables/disables the alternate MAC address 3 on Port 0.
0: Disables alternate MAC address on Port 0
1: Enables MAC address 01:00:5E:00:01:84 as a PTP address on Port 0
10
User Defined MAC Address Enable Port 0(Host MAC)
(MAC_USER_EN_MII)
This bit enables/disables the auxiliary MAC address on Port 0. The auxiliary
address is defined via the 1588_AUX_MAC_HI and 1588_AUX_MAC_LO
registers.
0: Disables auxiliary MAC address on Port 0
1: Enables auxiliary MAC address as a PTP address on Port 0
9
Lock Enable RX Port 0(Host MAC) (LOCK_RX_MII)
This bit enables/disables the RX lock. This lock prevents a 1588 capture
from overwriting the Clock, UUDI and Sequence ID values if the 1588 RX
interrupt for Port 0 is ready set due to a previous capture.
0: Disables RX Port 0 Lock
1: Enables RX Port 0 Lock
Note:
8
For Port 0, receive is defined as data from the switch fabric, while
transmit is to the switch fabric.
Lock Enable TX Port 0(Host MAC) (LOCK_TX_MII)
This bit enables/disables the TX lock. This lock prevents a 1588 capture
from overwriting the Clock, UUDI and Sequence ID values if the 1588 TX
interrupt for Port 0 is ready set due to a previous capture.
0: Disables TX Port 0 Lock
1: Enables TX Port 0 Lock
Note:
For Port 0, receive is defined as data from the switch fabric, while
transmit is to the switch fabric.
7
RESERVED
RO
-
6
Lock Enable GPIO 9 (LOCK_GPIO_9)
This bit enables/disables the GPIO 9 lock. This lock prevents a 1588 capture
from overwriting the Clock value if the 1588_GPIO9 interrupt in the 1588
Interrupt Status and Enable Register (1588_INT_STS_EN) is already set
due to a previous capture.
R/W
1b
0: Disables GPIO 9 Lock
1: Enables GPIO 9 Lock
Revision 2.0 (02-14-13)
224
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
5
Lock Enable GPIO 8 (LOCK_GPIO_8)
This bit enables/disables the GPIO 8 lock. This lock prevents a 1588 capture
from overwriting the Clock value if the 1588_GPIO8 interrupt in the 1588
Interrupt Status and Enable Register (1588_INT_STS_EN) is already set
due to a previous capture.
R/W
1b
R/W
00b
R/W
00b
R/W
0b
0: Disables GPIO 8 Lock
1: Enables GPIO 8 Lock
4:3
GPIO 9 Clock Event Mode (GPIO_EVENT_9)
These bits determine the output on GPIO 9 when a clock target compare
event occurs.
00: 100ns pulse output
01: Toggle output
10: 1588_TIMER_INT bit value in the 1588_INT_STS_EN register output
11: RESERVED
2:1
Note:
The 1588_GPIO_OE[9] bit in the General Purpose I/O
Configuration Register (GPIO_CFG) must be set in order for the
GPIO output to be controlled by the 1588 block.
Note:
The polarity of the pulse or level is set by the
GPIO_EVENT_POL_9 bit in the General Purpose I/O Configuration
Register (GPIO_CFG). The GPIOBUF[9] bit still determines the
GPIO buffer type.
GPIO 8 Clock Event Mode (GPIO_EVENT_8)
These bits determine the output on GPIO 8 when a clock target compare
event occurs.
00: 100ns pulse output
01: Toggle output
10: 1588_TIMER_INT bit value in the 1588_INT_STS_EN register output
11: RESERVED
0
Note:
The 1588_GPIO_OE[8] bit in the General Purpose I/O
Configuration Register (GPIO_CFG) must be set in order for the
GPIO output to be controlled by the 1588 block.
Note:
The polarity of the pulse or level is set by the
GPIO_EVENT_POL_8 bit in the General Purpose I/O Configuration
Register (GPIO_CFG). The GPIOBUF[8] bit still determines the
GPIO buffer type.
Reload/Add (RELOAD_ADD)
This bit determines the course of action when a clock target compare event
occurs. When set, the 1588 Clock Target High-DWORD Register
(1588_CLOCK_TARGET_HI) and 1588 Clock Target Low-DWORD Register
(1588_CLOCK_TARGET_LO) are loaded from the 1588 Clock Target
Reload High-DWORD Register (1588_CLOCK_TARGET_RELOAD_HI) and
1588 Clock Target Reload/Add Low-DWORD Register
(1588_CLOCK_TARGET_RELOAD_LO) when a clock target compare event
occurs. When low, the Clock Target Low and High Registers are
incremented by the Clock Target Reload Low Register when a clock target
compare event occurs.
0: Reload upon a clock target compare event
1: Increment upon a clock target compare event
SMSC LAN9312
225
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.23
1588 Interrupt Status and Enable Register (1588_INT_STS_EN)
Offset:
198h
Size:
32 bits
This read/write register contains the IEEE 1588 interrupt status and enable bits.
Writing a 1 to any of the interrupt status bits acknowledges and clears the interrupt. If enabled, these
interrupt bits are cascaded into bit 29 (1588_EVNT) of the Interrupt Status Register (INT_STS). Writing
a 1 to any of the interrupt enable bits will enable the corresponding interrupt as a source. Status bits
will still reflect the status of the interrupt source regardless of whether the source is enabled as an
interrupt in this register. Bit 29 (1588_EVNT_EN) of the Interrupt Enable Register (INT_EN) must also
be set in order for an actual system level interrupt to occur. Refer to Chapter 5, "System Interrupts,"
on page 49 for additional information.
BITS
TYPE
DEFAULT
RESERVED
RO
-
24
1588 Port 2 RX Interrupt Enable (1588_PORT2_RX_EN)
R/W
0b
23
1588 Port 2 TX Interrupt Enable (1588_PORT2_TX_EN)
R/W
0b
22
1588 Port 1 RX Interrupt Enable (1588_PORT1_RX_EN)
R/W
0b
21
1588 Port 1 TX Interrupt Enable (1588_PORT1_TX_EN)
R/W
0b
20
1588 Port 0(Host MAC) RX Interrupt Enable (1588_MII_RX_EN)
R/W
0b
19
1588 Port 0(Host MAC) TX Interrupt Enable (1588_MII_TX_EN)
R/W
0b
18
GPIO9 1588 Interrupt Enable (1588_GPIO9_EN)
R/W
0b
17
GPIO8 1588 Interrupt Enable (1588_GPIO8_EN)
R/W
0b
16
1588 Timer Interrupt Enable (1588_TIMER_EN)
R/W
0b
RESERVED
RO
-
31:25
15:9
DESCRIPTION
8
1588 Port 2 RX Interrupt (1588_PORT2_RX_INT)
This interrupt indicates that a packet received by Port 2 matches the
configured PTP packet and the 1588 clock was captured.
R/WC
0b
7
1588 Port 2 TX Interrupt (1588_PORT2_TX_INT)
This interrupt indicates that a packet transmitted by Port 2 matches the
configured PTP packet and the 1588 clock was captured.
R/WC
0b
6
1588 Port 1 RX Interrupt (1588_PORT1_RX_INT)
This interrupt indicates that a packet received by Port 1 matches the
configured PTP packet and the 1588 clock was captured.
R/WC
0b
5
1588 Port 1 TX Interrupt (1588_PORT1_TX_INT)
This interrupt indicates that a packet transmitted by Port 1 matches the
configured PTP packet and the 1588 clock was captured.
R/WC
0b
4
1588 Port 0(Host MAC) RX Interrupt (1588_MII_RX_INT)
This interrupt indicates that a packet from the switch fabric to the Host MAC
the matches the configured PTP packet and the 1588 clock was captured.
R/WC
0b
Note:
For Port 0, receive is defined as data from the switch fabric, while
transmit is to the switch fabric.
Revision 2.0 (02-14-13)
226
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
3
1588 Port 0(Host MAC) TX Interrupt (1588_MII_TX_INT)
This interrupt indicates that a packet from the Host MAC to the switch fabric
matches the configured PTP packet and the 1588 clock was captured.
R/WC
0b
R/WC
0b
R/WC
0b
R/WC
0b
Note:
2
1588 GPIO9 Interrupt (1588_GPIO9_INT)
This interrupt indicates that an event on GPIO9 occurred and the 1588 clock
was captured. These interrupts are configured through the General Purpose
I/O Configuration Register (GPIO_CFG) register.
Note:
1
As 1588 capture inputs, GPIO inputs are edge sensitive and must
be active for greater than 40 nS to be recognized as interrupt
inputs.
1588 GPIO8 Interrupt (1588_GPIO8_INT)
This interrupt indicates that an event on GPIO8 occurred and the 1588 clock
was captured. These interrupts are configured through the General Purpose
I/O Configuration Register (GPIO_CFG) register.
Note:
0
For Port 0, receive is defined as data from the switch fabric, while
transmit is to the switch fabric.
As 1588 capture inputs, GPIO inputs are edge sensitive and must
be active for greater than 40 nS to be recognized as interrupt
inputs.
1588 Timer Interrupt (1588_TIMER_INT)
This interrupt indicates that the 1588 clock equaled or passed the Clock
Target value in the 1588 Clock Target High-DWORD Register
(1588_CLOCK_TARGET_HI) and 1588 Clock Target Low-DWORD Register
(1588_CLOCK_TARGET_LO).
Note:
SMSC LAN9312
This bit is also cleared by an active edge on GPIO[9:8] if enabled.
For the clear function, GPIO inputs are edge sensitive and must be
active for greater than 40 nS to be recognized as a clear input.
Refer to Section 13.2, "GPIO Operation," on page 162 for
additional information.
227
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.5.24
1588 Command Register (1588_CMD)
Offset:
19Ch
Size:
32 bits
This register is used to issue 1588 commands. Using the clock snapshot bit allows the host to properly
read the current IEEE 1588 clock values from the 1588 Clock High-DWORD Register
(1588_CLOCK_HI) and 1588 Clock Low-DWORD Register (1588_CLOCK_LO). Refer to section
Section 11.3, "IEEE 1588 Clock," on page 159 for additional information.
BITS
31:1
0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Clock Snapshot (1588_CLOCK_SNAPSHOT)
Setting this bit causes the current 1588 Clock High-DWORD Register
(1588_CLOCK_HI) and 1588 Clock Low-DWORD Register
(1588_CLOCK_LO) values to be saved so they can be read.
WO
SC
0b
Revision 2.0 (02-14-13)
228
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.6
Switch Fabric
This section details the memory mapped System CSR’s which are related to the Switch Fabric. The
flow control of all three ports of the switch fabric can be configured via the memory mapped System
CSR’s MANUAL_FC_1, MANUAL_FC_2 and MANUAL_FC_MII. The MAC address used by the switch
for Pause frames is configured via the SWITCH_MAC_ADDRH and SWITCH_MAC_ADDRL registers.
In addition, the SWITCH_CSR_CMD, SWITCH_CSR_DATA and SWITCH_CSR_DIRECT_DATA
registers serve as a memory mapped accessible interface to the full range of otherwise inaccessible
switch control and status registers. A list of all the switch fabric CSRs can be seen in Table 14.12. For
additional information on the switch fabric, including a full explanation on how to use the switch fabric
CSR interface registers, refer to Chapter 6, "Switch Fabric," on page 55. For detailed descriptions of
the Switch Fabric CSR’s that are accessible via these interface registers, refer to section Section 14.5,
"Switch Fabric Control and Status Registers".
14.2.6.1
Port 1 Manual Flow Control Register (MANUAL_FC_1)
Offset:
1A0h
Size:
32 bits
This read/write register allows for the manual configuration of the switch Port 1 flow control. This
register also provides read back of the currently enabled flow control settings, whether set manually
or Auto-Negotiated. Refer to Section 6.2.3, "Flow Control Enable Logic," on page 58 for additional
information.
Note: The flow control values in the PHY_AN_ADV_1 register (see Section 14.4.2.5, on page 294)
within the PHY are not affected by the values of this register.
BITS
31:7
6
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Port 1 Backpressure Enable (BP_EN_1)
This bit enables/disables the generation of half-duplex backpressure on
switch Port 1.
R/W
Note 14.4
RO
Note 14.5
RO
Note 14.5
RO
Note 14.5
R/W
Note 14.6
0: Disable backpressure
1: Enable backpressure
5
Port 1 Current Duplex (CUR_DUP_1)
This bit indicates the actual duplex setting of switch Port 1.
0: Full-Duplex
1: Half-Duplex
4
Port 1 Current Receive Flow Control Enable (CUR_RX_FC_1)
This bit indicates the actual receive flow setting of switch Port 1.
0: Flow control receive is currently disabled
1: Flow control receive is currently enabled
3
Port 1 Current Transmit Flow Control Enable (CUR_TX_FC_1)
This bit indicates the actual transmit flow setting of switch Port 1.
0: Flow control transmit is currently disabled
1: Flow control transmit is currently enabled
2
Port 1 Full-Duplex Receive Flow Control Enable (RX_FC_1)
When the MANUAL_FC_1 bit is set, or Auto-Negotiation is disabled, this bit
enables/disables the detection of full-duplex Pause packets on switch Port 1.
0: Disable flow control receive
1: Enable flow control receive
SMSC LAN9312
229
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
1
Port 1 Full-Duplex Transmit Flow Control Enable (TX_FC_1)
When the MANUAL_FC_1 bit is set, or Auto-Negotiation is disabled, this bit
enables/disables full-duplex Pause packets to be generated on switch Port
1.
R/W
Note 14.6
R/W
Note 14.7
0: Disable flow control transmit
1: Enable flow control transmit
0
Port 1 Full-Duplex Manual Flow Control Select (MANUAL_FC_1)
This bit toggles flow control selection between manual and auto-negotiation.
0: If auto-negotiation is enabled, the auto-negotiation function
determines the flow control of switch Port 1 (RX_FC_1 and TX_FC_1
values ignored). If auto-negotiation is disabled, the RX_FC_1 and
TX_FC_1 values are used.
1: TX_FC_1 and RX_FC_1 bits determine the flow control of switch Port
1 when in full-duplex mode
Note 14.4 The default value of this field is determined by the BP_EN_strap_1 configuration strap. The
strap values are loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the values, this register is updated with the new values.
See Section 4.2.4, "Configuration Straps," on page 40 for more information.
Note 14.5 The default value of this bit is determined by multiple strap settings. The strap values are
loaded during reset and can be re-written by the EEPROM Loader. Once the EEPROM
Loader re-writes the values, this register is updated with the new values. Refer to Section
6.2.3, "Flow Control Enable Logic," on page 58 for additional information.
Note 14.6 The default value of this field is determined by the FD_FC_strap_1 configuration strap. The
strap values are loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the values, this register is updated with the new values.
See Section 4.2.4, "Configuration Straps," on page 40 for more information.
Note 14.7 The default value of this field is determined by the manual_FC_strap_1 configuration strap.
The strap values are loaded during reset and can be re-written by the EEPROM Loader.
Once the EEPROM Loader re-writes the values, this register is updated with the new
values. See Section 4.2.4, "Configuration Straps," on page 40 for more information.
Revision 2.0 (02-14-13)
230
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.6.2
Port 2 Manual Flow Control Register (MANUAL_FC_2)
Offset:
1A4h
Size:
32 bits
This read/write register allows for the manual configuration of the switch Port 2 flow control. This
register also provides read back of the currently enabled flow control settings, whether set manually
or Auto-Negotiated. Refer to Section 6.2.3, "Flow Control Enable Logic," on page 58 for additional
information.
Note: The flow control values in the PHY_AN_ADV_2 register (see Section 14.4.2.5, on page 294)
within the PHY are not affected by the values of this register.
BITS
31:7
6
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Port 2 Backpressure Enable (BP_EN_2)
This bit enables/disables the generation of half-duplex backpressure on
switch Port 2.
R/W
Note 14.8
RO
Note 14.9
RO
Note 14.9
RO
Note 14.9
R/W
Note 14.10
R/W
Note 14.10
0: Disable backpressure
1: Enable backpressure
5
Port 2 Current Duplex (CUR_DUP_2)
This bit indicates the actual duplex setting of switch Port 2.
0: Full-Duplex
1: Half-Duplex
4
Port 2 Current Receive Flow Control Enable (CUR_RX_FC_2)
This bit indicates the actual receive flow setting of switch Port 2.
0: Flow control receive is currently disabled
1: Flow control receive is currently enabled
3
Port 2 Current Transmit Flow Control Enable (CUR_TX_FC_2)
This bit indicates the actual transmit flow setting of switch Port 2.
0: Flow control transmit is currently disabled
1: Flow control transmit is currently enabled
2
Port 2 Full-Duplex Receive Flow Control Enable (RX_FC_2)
When the MANUAL_FC_2 bit is set, or Auto-Negotiation is disabled, this bit
enables/disables the detection of full-duplex Pause packets on switch Port 2.
0: Disable flow control receive
1: Enable flow control receive
1
Port 2 Full-Duplex Transmit Flow Control Enable (TX_FC_2)
When the MANUAL_FC_2 bit is set, or Auto-Negotiation is disabled, this bit
enables/disables full-duplex Pause packets to be generated on switch Port
2.
0: Disable flow control transmit
1: Enable flow control transmit
SMSC LAN9312
231
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
0
Port 2 Full-Duplex Manual Flow Control Select (MANUAL_FC_2)
This bit toggles flow control selection between manual and auto-negotiation.
R/W
Note 14.11
0: If auto-negotiation is enabled, the auto-negotiation function
determines the flow control of switch Port 2 (RX_FC_2 and TX_FC_2
values ignored). If auto-negotiation is disabled, the RX_FC_2 and
TX_FC_2 values are used.
1: TX_FC_2 and RX_FC_2 bits determine the flow control of switch Port
2 when in full-duplex mode
Note 14.8 The default value of this field is determined by the BP_EN_strap_2 configuration strap. The
strap values are loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the values, this register is updated with the new values.
See Section 4.2.4, "Configuration Straps," on page 40 for more information.
Note 14.9 The default value of this bit is determined by multiple strap settings. The strap values are
loaded during reset and can be re-written by the EEPROM Loader. Once the EEPROM
Loader re-writes the values, this register is updated with the new values. Refer to Section
6.2.3, "Flow Control Enable Logic," on page 58 for additional information.
Note 14.10 The default value of this field is determined by the FD_FC_strap_2 configuration strap. The
strap values are loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the values, this register is updated with the new values.
See Section 4.2.4, "Configuration Straps," on page 40 for more information.
Note 14.11 The default value of this field is determined by the manual_FC_strap_2 configuration strap.
The strap values are loaded during reset and can be re-written by the EEPROM Loader.
Once the EEPROM Loader re-writes the values, this register is updated with the new
values. See Section 4.2.4, "Configuration Straps," on page 40 for more information.
Revision 2.0 (02-14-13)
232
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.6.3
Port 0(Host MAC) Manual Flow Control Register (MANUAL_FC_MII)
Offset:
1A8h
Size:
32 bits
This read/write register allows for the manual configuration of the switch Port 0(Host MAC) flow control.
This register also provides read back of the currently enabled flow control settings, whether set
manually or Auto-Negotiated. Refer to Section 6.2.3, "Flow Control Enable Logic," on page 58 for
additional information.
Note: The flow control values in the Section 14.2.8.5, "Virtual PHY Auto-Negotiation Advertisement
Register (VPHY_AN_ADV)," on page 252 are not affected by the values of this register.
BITS
31:8
7
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Port 0 Hard-wired Flow Control (HW_FC_MII)
When set to “1”, the Host MACs RX FIFO level is connected to the switch
engine’s transmitter and the switch engines RX FIFO level is connected to
the Host MACs transmitter. This achieves lower latency flow control.
R/W
0b
R/W
Note 14.12
RO
Note 14.13
RO
Note 14.13
RO
Note 14.13
R/W
Note 14.14
Note:
6
All other flow control methods must be disabled when using this
feature. (MANUAL_FC_MII should be set, TX_FC_MII,
RX_FC_MII, and BP_EN_MII should be cleared. FCANY, FCADD,
FCBRD, and FCMULT in the AFC_CFG register should be
cleared).
Port 0 Backpressure Enable (BP_EN_MII)
This bit enables/disables the generation of half-duplex backpressure on
switch Port 0.
0: Disable backpressure
1: Enable backpressure
5
Port 0 Current Duplex (CUR_DUP_MII)
This bit indicates the actual duplex setting of the switch Port 0.
0: Full-Duplex
1: Half-Duplex
4
Port 0 Current Receive Flow Control Enable (CUR_RX_FC_MII)
This bit indicates the actual receive flow setting of switch Port 0
0: Flow control receive is currently disabled
1: Flow control receive is currently enabled
3
Port 0 Current Transmit Flow Control Enable (CUR_TX_FC_MII)
This bit indicates the actual transmit flow setting of switch Port 0.
0: Flow control transmit is currently disabled
1: Flow control transmit is currently enabled
2
Port 0 Receive Flow Control Enable (RX_FC_MII)
When the MANUAL_FC_MII bit is set, or Virtual Auto-Negotiation is
disabled, this bit enables/disables the detection of full-duplex Pause packets
on switch Port 0.
0: Disable flow control receive
1: Enable flow control receive
SMSC LAN9312
233
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
1
Port 0 Transmit Flow Control Enable (TX_FC_MII)
When the MANUAL_FC_MII bit is set, or Virtual Auto-Negotiation is
disabled, this bit enables/disables full-duplex Pause packets to be generated
on switch Port 0.
R/W
Note 14.14
R/W
Note 14.15
0: Disable flow control transmit
1: Enable flow control transmit
0
Port 0 Full-Duplex Manual Flow Control Select (MANUAL_FC_MII)
This bit toggles flow control selection between manual and auto-negotiation.
0: If auto-negotiation is enabled, the auto-negotiation function
determines the flow control of switch Port 0 (RX_FC_MII and
TX_FC_MII values ignored). If auto-negotiation is disabled, the
RX_FC_MII and TX_FC_MII values are used.
1: TX_FC_MII and RX_FC_MII bits determine the flow control of switch
Port 0 when in full-duplex mode
Note 14.12 The default value of this field is determined by the BP_EN_strap_mii configuration strap.
The strap value is loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the value, this register is updated with the new values. See
Section 4.2.4, "Configuration Straps," on page 40 for more information.
Note 14.13 The default value of this bit is determined by multiple strap settings. The strap values are
loaded during reset and can be re-written by the EEPROM Loader. Once the EEPROM
Loader re-writes the values, this register is updated with the new values. Refer to Section
6.2.3, "Flow Control Enable Logic," on page 58 for additional information.
Note 14.14 The default value of this field is determined by the FD_FC_strap_mii configuration strap.
The strap value is loaded during reset and can be re-written by the EEPROM Loader. Once
the EEPROM Loader re-writes the value, this register is updated with the new values. See
Section 4.2.4, "Configuration Straps," on page 40 for more information.
Note 14.15 The default value of this field is determined by the manual_FC_strap_mii configuration
strap. The strap value is loaded during reset and can be re-written by the EEPROM
Loader. Once the EEPROM Loader re-writes the value, this register is updated with the
new values. See Section 4.2.4, "Configuration Straps," on page 40 for more information.
Revision 2.0 (02-14-13)
234
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.6.4
Switch Fabric CSR Interface Data Register (SWITCH_CSR_DATA)
Offset:
1ACh
Size:
32 bits
This read/write register is used in conjunction with the Switch Fabric CSR Interface Command Register
(SWITCH_CSR_CMD) to perform read and write operations with the Switch Fabric CSR’s. Refer to
Section 14.5, "Switch Fabric Control and Status Registers," on page 308 for details on the registers
indirectly accessible via this register.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Switch CSR Data (CSR_DATA)
This field contains the value read from or written to the Switch Fabric CSR.
The Switch Fabric CSR is selected via the CSR Address (CSR_ADDR[15:0])
bits of the Switch Fabric CSR Interface Command Register
(SWITCH_CSR_CMD).
R/W
00000000h
Upon a read, the value returned depends on the R/nW bit in the Switch
Fabric CSR Interface Command Register (SWITCH_CSR_CMD). If R/nW is
set, the data is from the switch fabric. If R/nW is cleared, the data is the
value that was last written into this register.
SMSC LAN9312
235
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.6.5
Switch Fabric CSR Interface Command Register (SWITCH_CSR_CMD)
Offset:
1B0h
Size:
32 bits
This read/write register is used in conjunction with the Switch Fabric CSR Interface Data Register
(SWITCH_CSR_DATA) to control the read and write operations to the various Switch Fabric CSR’s.
Refer to Section 14.5, "Switch Fabric Control and Status Registers," on page 308 for details on the
registers indirectly accessible via this register.
BITS
DESCRIPTION
TYPE
DEFAULT
31
CSR Busy (CSR_BUSY)
When a 1 is written to this bit, the read or write operation (as determined by
the R_nW bit) is performed to the specified Switch Fabric CSR in CSR
Address (CSR_ADDR[15:0]). This bit will remain set until the operation is
complete, at which time the bit will clear. In the case of a read, the clearing
of this bit indicates to the Host that valid data can be read from the Switch
Fabric CSR Interface Data Register (SWITCH_CSR_DATA). The
SWITCH_CSR_CMD and SWITCH_CSR_DATA registers should not be
modified until this bit is cleared.
R/W
SC
0b
30
Read/Write (R_nW)
This bit determines whether a read or write operation is performed by the
Host to the specified Switch Engine CSR.
R/W
0b
R/W
0b
R/W
0b
RO
-
0: Write
1: Read
29
Auto Increment (AUTO_INC)
This bit enables/disables the auto increment feature.
When this bit is set, a write to the Switch Fabric CSR Interface Data Register
(SWITCH_CSR_DATA) register will automatically set the CSR Busy
(CSR_BUSY) bit. Once the write command is finished, the CSR Address
(CSR_ADDR[15:0]) will automatically increment.
When this bit is set, a read from the Switch Fabric CSR Interface Data
Register (SWITCH_CSR_DATA) will automatically increment the CSR
Address (CSR_ADDR[15:0]) and set the CSR Busy (CSR_BUSY) bit. This
bit should be cleared by software before the last read from the
SWITCH_CSR_DATA register.
0: Disable Auto Increment
1: Enable Auto Increment
Note:
28
This bit has precedence over the Auto Decrement (AUTO_DEC) bit
Auto Decrement (AUTO_DEC)
This bit enables/disables the auto decrement feature.
When this bit is set, a write to the Switch Fabric CSR Interface Data Register
(SWITCH_CSR_DATA) will automatically set the CSR Busy (CSR_BUSY)
bit. Once the write command is finished, the CSR Address
(CSR_ADDR[15:0]) will automatically decrement.
When this bit is set, a read from the Switch Fabric CSR Interface Data
Register (SWITCH_CSR_DATA) will automatically decrement the CSR
Address (CSR_ADDR[15:0]) and set the CSR Busy (CSR_BUSY) bit. This
bit should be cleared by software before the last read from the
SWITCH_CSR_DATA register.
0: Disable Auto Decrement
1: Enable Auto Decrement
27:20
RESERVED
Revision 2.0 (02-14-13)
236
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
19:16
CSR Byte Enable (CSR_BE[3:0])
This field is a 4-bit byte enable used for selection of valid bytes during write
operations. Bytes which are not selected will not be written to the
corresponding Switch Engine CSR.
R/W
0h
R/W
00h
CSR_BE[3]
CSR_BE[2]
CSR_BE[1]
CSR_BE[0]
corresponds
corresponds
corresponds
corresponds
to
to
to
to
register
register
register
register
data
data
data
data
bits
bits
bits
bits
[31:24]
[23:16]
[15:8]
[7:0]
Typically all four byte enables should be set for auto increment and auto
decrement operations.
15:0
CSR Address (CSR_ADDR[15:0])
This field selects the 16-bit address of the Switch Fabric CSR that will be
accessed with a read or write operation. Refer to Table 14.12, “Indirectly
Accessible Switch Control and Status Registers,” on page 308 for a list of
Switch Fabric CSR addresses.
SMSC LAN9312
237
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.6.6
Switch Fabric MAC Address High Register (SWITCH_MAC_ADDRH)
Offset:
1F0h
Size:
32 bits
This register contains the upper 16-bits of the MAC address used by the switch for Pause frames. This
register is used in conjunction with Switch Fabric MAC Address Low Register
(SWITCH_MAC_ADDRL). The contents of this register are optionally loaded from the EEPROM at
power-on through the EEPROM Loader if a programmed EEPROM is detected. The least significant
byte of this register (bits [7:0]) is loaded from address 05h of the EEPROM. The second byte (bits
[15:8]) is loaded from address 06h of the EEPROM. These EEPROM values are also loaded into the
Host MAC Address High Register (HMAC_ADDRH). The Host can update the contents of this field
after the initialization process has completed.
Refer to Section 9.6, "Host MAC Address," on page 119 for details on how the EEPROM Loader loads
this register. Section 10.2.4, "EEPROM Loader," on page 149 contains additional details on using the
EEPROM Loader.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:0
Physical Address[47:32]
This field contains the upper 16-bits (47:32) of the physical address of the
Switch Fabric MACs.
R/W
FFFFh
Revision 2.0 (02-14-13)
238
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.6.7
Switch Fabric MAC Address Low Register (SWITCH_MAC_ADDRL)
Offset:
1F4h
Size:
32 bits
This register contains the lower 32-bits of the MAC address used by the switch for Pause frames. This
register is used in conjunction with Switch Fabric MAC Address High Register
(SWITCH_MAC_ADDRH). The contents of this register are optionally loaded from the EEPROM at
power-on through the EEPROM Loader if a programmed EEPROM is detected. The least significant
byte of this register (bits [7:0]) is loaded from address 01h of the EEPROM. The most significant byte
(bits [31:24]) is loaded from address 04h of the EEPROM. These EEPROM values are also loaded
into the Host MAC Address Low Register (HMAC_ADDRL). The Host can update the contents of this
field after the initialization process has completed.
Refer to Section 9.6, "Host MAC Address," on page 119 for details on how the EEPROM Loader loads
this register. Refer to Section 10.2.4, "EEPROM Loader," on page 149 for information on using the
EEPROM Loader.
BITS
31:0
DESCRIPTION
Physical Address[31:0]
This field contains the lower 32-bits (31:0) of the physical address of the
Switch Fabric MACs.
SMSC LAN9312
239
DATASHEET
TYPE
DEFAULT
R/W
FF0F8000h
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.6.8
Switch Fabric CSR Interface Direct Data Register (SWITCH_CSR_DIRECT_DATA)
Offset:
200h - 2DCh
Size:
32 bits
This write-only register set is used to perform directly addressed write operations to the Switch Fabric
CSR’s. Using this set of registers, writes can be directly addressed to select Switch Fabric registers,
as specified in Table 14.3.
Writes within the Switch Fabric CSR Interface Direct Data Register (SWITCH_CSR_DIRECT_DATA)
address range automatically set the appropriate address, set the four byte enable bits, clear the R/nW
bit and set the Busy bit in the Switch Fabric CSR Interface Command Register (SWITCH_CSR_CMD).
The completion of the write cycle is indicated when the Busy bit is cleared. The address that is set in
the Switch Fabric CSR Interface Command Register (SWITCH_CSR_CMD) is mapped via Table 14.3.
For more information on this method of writing to the Switch Fabric CSR’s, refer to Section 6.2.3, "Flow
Control Enable Logic," on page 58.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Switch CSR Data (CSR_DATA)
This field contains the value to be written to the corresponding Switch Fabric
register.
WO
00000000h
Note: This set of registers is for write operations only. Reads can be performed via the Switch Fabric
CSR Interface Command Register (SWITCH_CSR_CMD) and Switch Fabric CSR Interface
Data Register (SWITCH_CSR_DATA) registers only.
Table 14.3 Switch Fabric CSR to SWITCH_CSR_DIRECT_DATA Address Range Map
REGISTER NAME
SWITCH FABRIC CSR
REGISTER #
SWITCH_CSR_DIRECT_DATA
ADDRESS
General Switch CSRs
SW_RESET
0001h
200h
SW_IMR
0004h
204h
Switch Port 0 CSRs
MAC_RX_CFG_MII
0401h
208h
MAC_TX_CFG_MII
0440h
20Ch
MAC_TX_FC_SETTINGS_MII
0441h
210h
MAC_IMR_MII
0480h
214h
Switch Port 1 CSRs
MAC_RX_CFG_1
0801h
218h
MAC_TX_CFG_1
0840h
21Ch
MAC_TX_FC_SETTINGS_1
0841h
220h
MAC_IMR_1
0880h
224h
Switch Port 2 CSRs
MAC_RX_CFG_2
Revision 2.0 (02-14-13)
0C01h
240
DATASHEET
228h
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.3 Switch Fabric CSR to SWITCH_CSR_DIRECT_DATA Address Range Map (continued)
REGISTER NAME
SWITCH FABRIC CSR
REGISTER #
SWITCH_CSR_DIRECT_DATA
ADDRESS
MAC_TX_CFG_2
0C40h
22Ch
MAC_TX_FC_SETTINGS_2
0C41h
230h
MAC_IMR_2
0C80h
234h
Switch Engine CSRs
SWE_ALR_CMD
1800h
238h
SWE_ALR_WR_DAT_0
1801h
23Ch
SWE_ALR_WR_DAT_1
1802h
240h
SWE_ALR_CFG
1809h
244h
SWE_VLAN_CMD
180Bh
248h
SWE_VLAN_WR_DATA
180Ch
24Ch
SWE_DIFFSERV_TBL_CMD
1811h
250h
SWE_DIFFSERV_TBL_WR_DATA
1812h
254h
SWE_GLB_INGRESS_CFG
1840h
258h
SWE_PORT_INGRESS_CFG
1841h
25Ch
SWE_ADMT_ONLY_VLAN
1842h
260h
SWE_PORT_STATE
1843h
264h
SWE_PRI_TO_QUE
1845h
268h
SWE_PORT_MIRROR
1846h
26Ch
SWE_INGRESS_PORT_TYP
1847h
270h
SWE_BCST_THROT
1848h
274h
SWE_ADMT_N_MEMBER
1849h
278h
SWE_INGRESS_RATE_CFG
184Ah
27Ch
SWE_INGRESS_RATE_CMD
184Bh
280h
SWE_INGRESS_RATE_WR_DATA
184Dh
284h
SWE_INGRESS_REGEN_TBL_MII
1855h
288h
SWE_INGRESS_REGEN_TBL_1
1856h
28Ch
SWE_INGRESS_REGEN_TBL_2
1857h
290h
SWE_IMR
1880h
294h
Buffer Manager (BM) CSRs
BM_CFG
1C00h
298h
BM_DROP_LVL
1C01h
29Ch
BM_FC_PAUSE_LVL
1C02h
2A0h
SMSC LAN9312
241
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.3 Switch Fabric CSR to SWITCH_CSR_DIRECT_DATA Address Range Map (continued)
REGISTER NAME
SWITCH FABRIC CSR
REGISTER #
SWITCH_CSR_DIRECT_DATA
ADDRESS
BM_FC_RESUME_LVL
1C03h
2A4h
BM_BCST_LVL
1C04h
2A8h
BM_RNDM_DSCRD_TBL_CMD
1C09h
2ACh
BM_RNDM_DSCRD_TBL_WDATA
1C0Ah
2B0h
BM_EGRSS_PORT_TYPE
1C0Ch
2B4h
BM_EGRSS_RATE_00_01
1C0Dh
2B8h
BM_EGRSS_RATE_02_03
1C0Eh
2BCh
BM_EGRSS_RATE_10_11
1C0Fh
2C0h
BM_EGRSS_RATE_12_13
1C10h
2C4h
BM_EGRSS_RATE_20_21
1C11h
2C8h
BM_EGRSS_RATE_22_23
1C12h
2CCh
BM_VLAN_MII
1C13h
2D0h
BM_VLAN_1
1C14h
2D4h
BM_VLAN_2
1C15h
2D8h
BM_IMR
1C20h
2DCh
Revision 2.0 (02-14-13)
242
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.7
PHY Management Interface (PMI)
The PMI registers are used (by the EEPROM Loader only) to indirectly access the PHY registers.
Refer to Section 14.4, "Ethernet PHY Control and Status Registers," on page 286 for additional
information on the PHY registers.
Note: These registers are only accessible by the EEPROM Loader and NOT by the Host bus. Refer
to Section 10.2.4, "EEPROM Loader," on page 149 for additional information.
14.2.7.1
PHY Management Interface Data Register (PMI_DATA)
Offset:
0A4h
EEPROM Loader
Access Only
Size:
32 bits
This register is used in conjunction with the PHY Management Interface Access Register
(PMI_ACCESS) to perform write operations to the PHYs.
Note: This register is only accessible by the EEPROM Loader and NOT by the Host bus. Refer to
Section 10.2.4, "EEPROM Loader," on page 149 for additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
-
31:16
RESERVED
RO
15:0
MII Data
This field contains the value written to the PHYs. For a write operation, this
register should be first written with the desired data.
WO
SMSC LAN9312
243
DATASHEET
00000000h
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.7.2
PHY Management Interface Access Register (PMI_ACCESS)
Offset:
0A8h
EEPROM Loader
Access Only
Size:
32 bits
This register is used to control the management cycles to the PHYs. A PHY access is initiated when
this register is written. This register is used in conjunction with the PHY Management Interface Data
Register (PMI_DATA) to perform write operations to the PHYs.
Note: This register is only accessible by the EEPROM Loader and NOT by the Host bus. Refer to
Section 10.2.4, "EEPROM Loader," on page 149 for additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
-
31:16
RESERVED
RO
15:11
PHY Address (PHY_ADDR)
These bits select the PHY device being accessed. Refer to Section 7.1.1,
"PHY Addressing," on page 82 for information on PHY address
assignments.
WO
10:6
MII Register Index (MIIRINDA)
These bits select the desired MII register in the PHY. Refer to Section 14.4,
"Ethernet PHY Control and Status Registers," on page 286 for detailed
descriptions on all PHY registers.
WO
5:2
RESERVED
RO
1
RESERVED
Note:
0
This bit must always be written with a value of 1.
RESERVED
Revision 2.0 (02-14-13)
WO
RO
244
DATASHEET
00000b
00000b
0b
0b
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.8
Virtual PHY
This section details the Virtual PHY System CSR’s. These registers provide status and control
information similar to that of a real PHY while maintaining IEEE 802.3 compatibility. The Virtual PHY
registers are addressable via the memory map, as described in Table 14.1, as well as serially via the
MII management protocol (IEEE 802.3 clause 22). When accessed serially, these registers are
accessed indirectly through the Host MAC MII Access Register (HMAC_MII_ACC) and Host MAC MII
Data Register (HMAC_MII_DATA) via the MII serial management protocol specified in IEEE 802.3
clause 22. When being accessed serially, the Virtual PHY will respond when the PHY address equals
the address assigned by the phy_addr_sel_strap configuration strap, as defined in Section 7.1.1, "PHY
Addressing," on page 82. A list of all Virtual PHY register indexes for serial access can be seen in
Table 14.4. For more information on the Virtual PHY access modes, refer to section Section 14.4. For
Virtual PHY functionality and operation information, see Section 7.3, "Virtual PHY," on page 96.
Note: All Virtual PHY registers follow the IEEE 802.3 (clause 22.2.4) specified MII management
register set. All functionality and bit definitions comply with these standards. The IEEE 802.3
specified register index (in decimal) is included under the LAN9312 memory mapped offset of
each Virtual PHY register as a reference. For additional information, refer to the IEEE 802.3
Specification.
Note: When serially accessed, the Virtual PHY registers are only 16-bits wide, as is standard for MII
management of PHY’s.
Table 14.4 Virtual PHY MII Serially Adressable Register Index
INDEX #
SYMBOL
0
VPHY_BASIC_CTRL
Virtual PHY Basic Control Register, Section 14.2.8.1
1
VPHY_BASIC_STATUS
Virtual PHY Basic Status Register, Section 14.2.8.2
2
VPHY_ID_MSB
Virtual PHY Identification MSB Register, Section 14.2.8.3
3
VPHY_ID_LSB
Virtual PHY Identification LSB Register, Section 14.2.8.4
4
VPHY_AN_ADV
Virtual PHY Auto-Negotiation Advertisement Register,
Section 14.2.8.5
5
VPHY_AN_LP_BASE_ABILITY
6
VPHY_AN_EXP
31
VPHY_SPEC_CTRL_STATUS
SMSC LAN9312
REGISTER NAME
Virtual PHY Auto-Negotiation Link Partner Base Page Ability
Register, Section 14.2.8.6
Virtual PHY Auto-Negotiation Expansion Register,
Section 14.2.8.7
Virtual PHY Special Control/Status Register, Section 14.2.8.8
245
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.8.1
Virtual PHY Basic Control Register (VPHY_BASIC_CTRL)
Offset:
Index (decimal):
1C0h
0
Size:
32 bits
This read/write register is used to configure the Virtual PHY.
Note: This register is re-written in its entirety by the EEPROM Loader following the release or reset
or a RELOAD command. Refer to Section 10.2.4, "EEPROM Loader," on page 149 for more
information.
BITS
31:16
15
DESCRIPTION
TYPE
DEFAULT
RESERVED
(See Note 14.16)
RO
-
Reset (VPHY_RST)
When set, this bit resets all the Virtual PHY registers to their default state.
This bit is self clearing.
R/W
SC
0b
R/W
0b
R/W
0b
R/W
1b
0: Normal Operation
1: Reset
14
Loopback (VPHY_LOOPBACK)
This bit enables/disables the loopback mode. When enabled, transmissions
from the Host MAC are not sent to the switch fabric. Instead, they are looped
back onto the receive path.
0: Loopback mode disabled (normal operation)
1: Loopback mode enabled
13
Speed Select LSB (VPHY_SPEED_SEL_LSB)
This bit is used to set the speed of the Virtual PHY when the AutoNegotiation (VPHY_AN) bit is disabled.
0: 10 Mbps
1: 100 Mbps
12
Auto-Negotiation (VPHY_AN)
This bit enables/disables Auto-Negotiation. When enabled, the Speed Select
LSB (VPHY_SPEED_SEL_LSB) and Duplex Mode (VPHY_DUPLEX) bits
are overridden.
0: Auto-Negotiation disabled
1: Auto-Negotiation enabled
11
Power Down (VPHY_PWR_DWN)
This bit is not used by the Virtual PHY and has no effect.
R/W
0b
10
Isolate (VPHY_ISO)
This bit is not used by the Virtual PHY and has no effect.
R/W
0b
9
Restart Auto-Negotiation (VPHY_RST_AN)
When set, this bit updates the emulated Auto-Negotiation results.
R/W
SC
0b
R/W
0b
0: Normal operation
1: Auto-Negotiation restarted
8
Duplex Mode (VPHY_DUPLEX)
This bit is used to set the duplex when the Auto-Negotiation (VPHY_AN) bit
is disabled.
0: Half Duplex
1: Full Duplex
Revision 2.0 (02-14-13)
246
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
7
DESCRIPTION
TYPE
DEFAULT
R/W
0b
Speed Select MSB (VPHY_SPEED_SEL_MSB)
This bit is not used by the Virtual PHY and has no effect. The value returned
is always 0.
RO
0b
RESERVED
RO
-
Collision Test (VPHY_COL_TEST)
This bit enables/disables the collision test mode. When set, the collision
signal to the Host MAC is active during transmission from the Host MAC.
Note:
It is recommended that this bit be used only when in loopback
mode.
0: Collision test mode disabled
1: Collision test mode enabled
6
5:0
Note 14.16 The reserved bits 31-16 are used to pad the register to 32-bits so that each register is on
a DWORD boundary. When accessed serially (through the MII management protocol), the
register is 16-bits wide.
SMSC LAN9312
247
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.8.2
Virtual PHY Basic Status Register (VPHY_BASIC_STATUS)
Offset:
Index (decimal):
1C4h
1
Size:
32 bits
This register is used to monitor the status of the Virtual PHY.
BITS
31:16
15
DESCRIPTION
TYPE
DEFAULT
RESERVED
(See Note 14.17)
RO
-
100BASE-T4
This bit displays the status of 100BASE-T4 compatibility.
RO
0b
Note 14.18
RO
1b
RO
1b
RO
1b
RO
1b
RO
0b
Note 14.18
RO
0b
Note 14.18
RO
0b
Note 14.19
RO
-
0: PHY not able to perform 100BASE-T4
1: PHY able to perform 100BASE-T4
14
100BASE-X Full Duplex
This bit displays the status of 100BASE-X full duplex compatibility.
0: PHY not able to perform 100BASE-X full duplex
1: PHY able to perform 100BASE-X full duplex
13
100BASE-X Half Duplex
This bit displays the status of 100BASE-X half duplex compatibility.
0: PHY not able to perform 100BASE-X half duplex
1: PHY able to perform 100BASE-X half duplex
12
10BASE-T Full Duplex
This bit displays the status of 10BASE-T full duplex compatibility.
0: PHY not able to perform 10BASE-T full duplex
1: PHY able to perform 10BASE-T full duplex
11
10BASE-T Half Duplex
This bit displays the status of 10BASE-T half duplex compatibility.
0: PHY not able to perform 10BASE-T half duplex
1: PHY able to perform 10BASE-T half duplex
10
100BASE-T2 Full Duplex
This bit displays the status of 100BASE-T2 full duplex compatibility.
0: PHY not able to perform 100BASE-T2 full duplex
1: PHY able to perform 100BASE-T2 full duplex
9
100BASE-T2 Half Duplex
This bit displays the status of 100BASE-T2 half duplex compatibility.
0: PHY not able to perform 100BASE-T2 half duplex
1: PHY able to perform 100BASE-T2 half duplex
8
Extended Status
This bit displays whether extended status information is in register 15 (per
IEEE 802.3 clause 22.2.4).
0: No extended status information in Register 15
1: Extended status information in Register 15
7
RESERVED
Revision 2.0 (02-14-13)
248
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
6
MF Preamble Suppression
This bit indicates whether the Virtual PHY accepts management frames with
the preamble suppressed.
RO
0b
RO
1b
Note 14.20
RO
0b
Note 14.21
RO
1b
RO
1b
Note 14.21
RO
0b
Note 14.21
RO
1b
Note 14.22
0: Management frames with preamble suppressed not accepted
1: Management frames with preamble suppressed accepted
5
Auto-Negotiation Complete
This bit indicates the status of the Auto-Negotiation process.
0: Auto-Negotiation process not completed
1: Auto-Negotiation process completed
4
Remote Fault
This bit indicates if a remote fault condition has been detected.
0: No remote fault condition detected
1: Remote fault condition detected
3
Auto-Negotiation Ability
This bit indicates the status of the Virtual PHY’s auto-negotiation.
0: Virtual PHY is unable to perform auto-negotiation
1: Virtual PHY is able to perform auto-negotiation
2
Link Status
This bit indicates the status of the link.
0: Link is down
1: Link is up
1
Jabber Detect
This bit indicates the status of the jabber condition.
0: No jabber condition detected
1: Jabber condition detected
0
Extended Capability
This bit indicates whether extended register capability is supported.
0: Basic register set capabilities only
1: Extended register set capabilities
Note 14.17 The reserved bits 31-16 are used to pad the register to 32-bits so that each register is on
a DWORD boundary. When accessed serially (through the MII management protocol), the
register is 16-bits wide.
Note 14.18 The Virtual PHY supports 100BASE-X (half and full duplex) and 10BASE-T (half and full
duplex) only. All other modes will always return as 0 (unable to perform).
Note 14.19 The Virtual PHY does not support Register 15 or 1000 Mb/s operation. Thus this bit is
always returned as 0.
Note 14.20 The Auto-Negotiation Complete bit is first cleared on a reset, but set shortly after (when
the Auto-Negotiation process is run). Refer to Section 7.3.1, "Virtual PHY AutoNegotiation," on page 96 for additional details.
Note 14.21 The Virtual PHY never has remote faults, its link is always up, and does not detect jabber.
Note 14.22 The VIrtual PHY supports basic and some extended register capability. The Virtual PHY
supports Registers 0-6 (per the IEEE 802.3 specification).
SMSC LAN9312
249
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.8.3
Virtual PHY Identification MSB Register (VPHY_ID_MSB)
Offset:
Index (decimal):
1C8h
2
Size:
32 bits
This read/write register contains the MSB of the Virtual PHY Organizationally Unique Identifier (OUI).
The LSB of the Virtual PHY OUI is contained in the Virtual PHY Identification LSB Register
(VPHY_ID_LSB).
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
(See Note 14.23)
RO
-
15:0
PHY ID
This field contains the MSB of the Virtual PHY OUI (Note 14.24).
R/W
0000h
Note 14.23 The reserved bits 31-16 are used to pad the register to 32-bits so that each register is on
a DWORD boundary. When accessed serially (through the MII management protocol), the
register is 16-bits wide.
Note 14.24 IEEE allows a value of zero in each of the 32-bits of the PHY Identifier.
Revision 2.0 (02-14-13)
250
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.8.4
Virtual PHY Identification LSB Register (VPHY_ID_LSB)
Offset:
Index (decimal):
1CCh
3
Size:
32 bits
This read/write register contains the LSB of the Virtual PHY Organizationally Unique Identifier (OUI).
The MSB of the Virtual PHY OUI is contained in the Virtual PHY Identification MSB Register
(VPHY_ID_MSB).
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
(See Note 14.25)
RO
-
15:10
PHY ID
This field contains the lower 6-bits of the Virtual PHY OUI (Note 14.26).
R/W
000000b
9:4
Model Number
This field contains the 6-bit manufacturer’s model number of the Virtual PHY
(Note 14.26).
R/W
000000b
3:0
Revision Number
This field contain the 4-bit manufacturer’s revision number of the Virtual PHY
(Note 14.26).
R/W
0000b
Note 14.25 The reserved bits 31-16 are used to pad the register to 32-bits so that each register is on
a DWORD boundary. When accessed serially (through the MII management protocol), the
register is 16-bits wide.
Note 14.26 IEEE allows a value of zero in each of the 32-bits of the PHY Identifier.
SMSC LAN9312
251
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.8.5
Virtual PHY Auto-Negotiation Advertisement Register (VPHY_AN_ADV)
Offset:
Index (decimal):
1D0h
4
Size:
32 bits
This read/write register contains the advertised ability of the Virtual PHY and is used in the AutoNegotiation process with the link partner.
Note: This register is re-written in its entirety by the EEPROM Loader following the release or reset
or a RELOAD command. Refer to Section 10.2.4, "EEPROM Loader," on page 149 for more
information.
BITS
31:16
15
DESCRIPTION
TYPE
DEFAULT
RESERVED
(See Note 14.27)
RO
-
Next Page
This bit determines the advertised next page capability and is always 0.
RO
0b
Note 14.28
0: Virtual PHY does not advertise next page capability
1: Virtual PHY advertises next page capability
14
RESERVED
RO
-
13
Remote Fault
This bit is not used since there is no physical link partner.
RO
0b
Note 14.29
12
RESERVED
RO
-
11
Asymmetric Pause
This bit determines the advertised asymmetric pause capability.
R/W
0b
R/W
Note 14.30
RO
0b
Note 14.31
R/W
1b
R/W
1b
0: No Asymmetric PAUSE toward link partner advertised
1: Asymmetric PAUSE toward link partner advertised
10
Pause
This bit determines the advertised symmetric pause capability.
0: No Symmetric PAUSE toward link partner advertised
1: Symmetric PAUSE toward link partner advertised
9
100BASE-T4
This bit determines the advertised 100BASE-T4 capability and is always 0.
0: 100BASE-T4 ability not advertised
1: 100BASE-T4 ability advertised
8
100BASE-X Full Duplex
This bit determines the advertised 100BASE-X full duplex capability.
0: 100BASE-X full duplex ability not advertised
1: 100BASE-X full duplex ability advertised
7
100BASE-X Half Duplex
This bit determines the advertised 100BASE-X half duplex capability.
0: 100BASE-X half duplex ability not advertised
1: 100BASE-X half duplex ability advertised
Revision 2.0 (02-14-13)
252
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
6
DESCRIPTION
10BASE-T Full Duplex
This bit determines the advertised 10BASE-T full duplex capability.
TYPE
DEFAULT
R/W
1b
R/W
1b
R/W
00001b
Note 14.32
0: 10BASE-T full duplex ability not advertised
1: 10BASE-T full duplex ability advertised
5
10BASE-T Half Duplex
This bit determines the advertised 10BASE-T half duplex capability.
0: 10BASE-T half duplex ability not advertised
1: 10BASE-T half duplex ability advertised
4:0
Selector Field
This field identifies the type of message being sent by Auto-Negotiation.
00001: IEEE 802.3
Note 14.27 The reserved bits 31-16 are used to pad the register to 32-bits so that each register is on
a DWORD boundary. When accessed serially (through the MII management protocol), the
register is 16-bits wide.
Note 14.28 The Virtual PHY does not support next page capability. This bit value will always be 0.
Note 14.29 The Remote Fault bit is not useful since there is no actual link partner to send a fault to.
Note 14.30 The Pause bit defaults to 1 if the manual_FC_strap_mii strap is low, and 0 if the
manual_FC_strap_mii strap is high. Configuration strap values are latched upon the deassertion of a chip-level reset as described in Section 4.2.4, "Configuration Straps," on
page 40.
Note 14.31 Virtual 100BASE-T4 is not supported.
Note 14.32 The Virtual PHY supports only IEEE 802.3. Only a value of 00001b should be used in this
field.
SMSC LAN9312
253
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.8.6
Virtual PHY Auto-Negotiation Link Partner Base Page Ability Register (VPHY_AN_LP_BASE_ABILITY)
Offset:
Index (decimal):
1D4h
5
Size:
32 bits
This read-only register contains the advertised ability of the link partner’s PHY and is used in the AutoNegotiation process with the Virtual PHY. Because the Virtual PHY does not physically connect to an
actual link partner, the values in this register are emulated as described below.
BITS
31:16
15
DESCRIPTION
TYPE
DEFAULT
RESERVED
(See Note 14.33)
RO
-
Next Page
This bit indicates the emulated link partner PHY next page capability and is
always 0.
RO
0b
Note 14.34
RO
1b
Note 14.34
0: Link partner PHY does not advertise next page capability
1: Link partner PHY advertises next page capability
14
Acknowledge
This bit indicates whether the link code word has been received from the
partner and is always 1.
0: Link code word not yet received from partner
1: Link code word received from partner
13
Remote Fault
Since there is no physical link partner, this bit is not used and is always
returned as 0.
RO
0b
Note 14.34
12
RESERVED
RO
-
11
Asymmetric Pause
This bit indicates the emulated link partner PHY asymmetric pause
capability.
RO
Note 14.35
RO
Note 14.35
RO
0b
Note 14.34
RO
Note 14.36
0: No Asymmetric PAUSE toward link partner
1: Asymmetric PAUSE toward link partner
10
Pause
This bit indicates the emulated link partner PHY symmetric pause capability.
0: No Symmetric PAUSE toward link partner
1: Symmetric PAUSE toward link partner
9
100BASE-T4
This bit indicates the emulated link partner PHY 100BASE-T4 capability.
This bit is always 0.
0: 100BASE-T4 ability not supported
1: 100BASE-T4 ability supported
8
100BASE-X Full Duplex
This bit indicates the emulated link partner PHY 100BASE-X full duplex
capability.
0: 100BASE-X full duplex ability not supported
1: 100BASE-X full duplex ability supported
Revision 2.0 (02-14-13)
254
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
7
DESCRIPTION
100BASE-X Half Duplex
This bit indicates the emulated link partner PHY 100BASE-X half duplex
capability.
TYPE
DEFAULT
RO
Note 14.36
RO
Note 14.36
RO
Note 14.36
RO
00001b
0: 100BASE-X half duplex ability not supported
1: 100BASE-X half duplex ability supported
6
10BASE-T Full Duplex
This bit indicates the emulated link partner PHY 10BASE-T full duplex
capability.
0: 10BASE-T full duplex ability not supported
1: 10BASE-T full duplex ability supported
5
10BASE-T Half Duplex
This bit indicates the emulated link partner PHY 10BASE-T half duplex
capability.
0: 10BASE-T half duplex ability not supported
1: 10BASE-T half duplex ability supported
4:0
Selector Field
This field identifies the type of message being sent by Auto-Negotiation.
00001: IEEE 802.3
Note 14.33 The reserved bits 31-16 are used to pad the register to 32-bits so that each register is on
a DWORD boundary. When accessed serially (through the MII management protocol), the
register is 16-bits wide.
Note 14.34 The emulated link partner does not support next page, always instantly sends its link code
word, never sends a fault, and does not support 100BASE-T4.
Note 14.35 The emulated link partner’s asymmetric/symmetric pause ability is based upon the values
of the Asymmetric Pause and Pause bits of the Virtual PHY Auto-Negotiation
Advertisement Register (VPHY_AN_ADV). Thus the emulated link partner always
accommodates the request of the Virtual PHY, as shown in Table 14.5. See Section 7.3.1,
"Virtual PHY Auto-Negotiation," on page 96 for additional information.
Table 14.5 Emulated Link Partner Pause Flow Control Ability Default Values
VPHY Symmetric
Pause
(register 4.10)
VPHY Asymmetric
Pause
(register 4.11)
Link Partner
Symmetric Pause
(register 5.10)
Link Partner
Asymmetric Pause
(register 5.11)
No Flow Control Enabled
0
0
0
0
Symmetric Pause
1
0
1
0
Asymmetric Pause Towards
Switch
0
1
1
1
Asymmetric Pause Towards MAC
1
1
0
1
Note 14.36 The emulated link partner always has the following capabilities: 100BASE-X full duplex,
100BASE-X half duplex, 10BASE-T full duplex, and 10BASE-T half duplex. For more
information on the Virtual PHY auto-negotiation, see Section 7.3.1, "Virtual PHY AutoNegotiation," on page 96.
SMSC LAN9312
255
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.8.7
Virtual PHY Auto-Negotiation Expansion Register (VPHY_AN_EXP)
Offset:
Index (decimal):
1D8h
6
Size:
32 bits
This register is used in the Auto-Negotiation process.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
(See Note 14.37)
RO
-
15:5
RESERVED
RO
-
Parallel Detection Fault
This bit indicates whether a Parallel Detection Fault has been detected. This
bit is always 0.
RO
0b
Note 14.38
RO
0b
Note 14.39
RO
0b
Note 14.39
RO/LH
1b
Note 14.40
RO
1b
Note 14.41
4
0: A fault hasn’t been detected via the Parallel Detection function
1: A fault has been detected via the Parallel Detection function
3
Link Partner Next Page Able
This bit indicates whether the link partner has next page ability. This bit is
always 0.
0: Link partner does not contain next page capability
1: Link partner contains next page capability
2
Local Device Next Page Able
This bit indicates whether the local device has next page ability. This bit is
always 0.
0: Local device does not contain next page capability
1: Local device contains next page capability
1
Page Received
This bit indicates the reception of a new page.
0: A new page has not been received
1: A new page has been received
0
Link Partner Auto-Negotiation Able
This bit indicates the Auto-negotiation ability of the link partner.
0: Link partner is not Auto-Negotiation able
1: Link partner is Auto-Negotiation able
Note 14.37 The reserved bits 31-16 are used to pad the register to 32-bits so that each register is on
a DWORD boundary. When accessed serially (through the MII management protocol), the
register is 16-bits wide.
Note 14.38 Since the Virtual PHY link partner is emulated, there is never a Parallel Detection Fault
and this bit is always 0.
Note 14.39 Next page ability is not supported by the Virtual PHY or emulated link partner.
Note 14.40 The page received bit is clear when read. It is first cleared on reset, but set shortly
thereafter when the Auto-Negotiation process is run.
Note 14.41 The emulated link partner will show Auto-Negotiation able unless Auto-Negotiation fails (no
common bits between the advertised ability and the link partner ability).
Revision 2.0 (02-14-13)
256
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.8.8
Virtual PHY Special Control/Status Register (VPHY_SPECIAL_CONTROL_STATUS)
Offset:
Index (decimal):
1DCh
31
Size:
32 bits
This read/write register contains a current link speed/duplex indicator and SQE control.
BITS
TYPE
DEFAULT
RESERVED
(See Note 14.42)
RO
-
15
RESERVED
RO
-
14
Switch Looopback MII
When set, transmissions from the switch fabric Port 0(Host MAC) are not
sent to the Host MAC. Instead, they are looped back into the switch engine.
R/W
0b
RESERVED
RO
-
Switch Collision Test MII
When set, the collision signal to the switch fabric Port 0(Host MAC) is active
during transmission from the switch engine.
R/W
0b
31:16
DESCRIPTION
From the MAC viewpoint, this is effectively a FAR LOOPBACK.
If loopback is enabled during half-duplex operation, then the Enable Receive
Own Transmit bit in the Port x MAC Receive Configuration Register
(MAC_RX_CFG_x) must be set for this port. Otherwise, the switch fabric will
ignore receive activity when transmitting in half-duplex mode.
This mode works even if the Isolate bit of the Virtual PHY Basic Control
Register (VPHY_BASIC_CTRL) is set.
13:8
7
It is recommended that this bit be used only when using loopback mode.
6:5
RESERVED
RO
-
4:2
Current Speed/Duplex Indication
This field indicates the current speed and duplex of the Virtual PHY link.
RO
Note 14.43
RO
-
R/W
NASR
Note 14.45
[4]
[3]
[2]
Speed
Duplex
0
0
0
0
0
1
10Mbps
half-duplex
0
1
0
100Mbps
half-duplex
0
1
1
1
0
0
1
0
1
10Mbps
1
1
0
100Mbps
1
1
1
RESERVED
RESERVED
RESERVED
full-duplex
full-duplex
RESERVED
1
RESERVED
0
SQEOFF
This bit enables/disables the Signal Quality Error (Heartbeat) test.
Note 14.44
0: SQE test enabled
1: SQE test disabled
SMSC LAN9312
257
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Note 14.42 The reserved bits 31-16 are used to pad the register to 32-bits so that each register is on
a DWORD boundary. When accessed serially (through the MII management protocol), the
register is 16-bits wide.
Note 14.43 The default value of this field is the result of the Auto-Negotiation process if the AutoNegotiation (VPHY_AN) bit of the Virtual PHY Basic Control Register
(VPHY_BASIC_CTRL) is set. Otherwise, this field reflects the Speed Select LSB
(VPHY_SPEED_SEL_LSB) and Duplex Mode (VPHY_DUPLEX) bit settings of the
VPHY_BASIC_CTRL register. Refer to Section 7.3.1, "Virtual PHY Auto-Negotiation," on
page 96 for information on the Auto-Negotiation determination process of the Virtual PHY.
Note 14.44 Register bits designated as NASR are reset when the Virtual PHY Reset is generated via
the Reset Control Register (RESET_CTL) or Power Management Control Register
(PMT_CTRL). The NASR designation is only applicable when the Reset (VPHY_RST) bit
of the Virtual PHY Basic Control Register (VPHY_BASIC_CTRL) is set.
Note 14.45 The default value of this field is determined via the SQE_test_disable_strap_mii
configuration strap. Refer to Section 4.2.4, "Configuration Straps," on page 40 for
additional information.
Revision 2.0 (02-14-13)
258
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.9
Miscellaneous
This section details the remainder of the System CSR’s. These registers allow for monitoring and
configuration of various LAN9312 functions such as the Chip ID/revision, byte order testing, power
management, hardware configuration, general purpose timer, and free running counter.
14.2.9.1
Chip ID and Revision (ID_REV)
Offset:
050h
Size:
32 bits
This read-only register contains the ID and Revision fields for the LAN9312.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
Chip ID
This field indicates the chip ID.
RO
9312h
15:0
Chip Revision
This field indicates the design revision.
RO
Note 14.46
Note 14.46 Default value is dependent on device revision.
SMSC LAN9312
259
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.9.2
Byte Order Test Register (BYTE_TEST)
Offset:
064h
Size:
32 bits
This read-only register can be used to determine the byte ordering of the current configuration. Byte
ordering is a function of the host data bus width and endianess. Refer to Section 8.3, "Host Endianess,"
on page 99 for additional information on byte ordering.
Note: This register can be read while the LAN9312 is in the reset or not ready states.
The BYTE_TEST register can optionally be used as a dummy read register when assuring minimum
write-to-read or read-to-read timing. Refer to Section 8.4.2, "Special Restrictions on Back-to Back
Write-Read Cycles," on page 101 and Section 8.4.3, "Special Restrictions on Back-to-Back Read
Cycles," on page 105 for additional information.
BITS
31:0
DESCRIPTION
Byte Test (BYTE_TEST)
This field reflects the current byte ordering
Revision 2.0 (02-14-13)
260
DATASHEET
TYPE
DEFAULT
RO
87654321h
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.9.3
Hardware Configuration Register (HW_CFG)
Offset:
074h
Size:
32 bits
This register allows the configuration of various hardware features including TX/RX FIFO sizes, Host
MAC transmit threshold properties, and software reset. A detailed explanation of the allowable settings
for FIFO memory allocation can be found in Section 9.7.3, "FIFO Memory Allocation Configuration,"
on page 121.
Note: This register can be polled while the LAN9312 is in the reset or not ready state (READY bit is
cleared).
BITS
31:28
27
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Device Ready (READY)
When set, this bit indicates that the LAN9312 is ready to be accessed. Upon
power-up, nRST reset, soft reset, or digital reset, the host processor may
interrogate this field as an indication that the LAN9312 has stabilized and is
fully active.
RO
0b
This bit can cause an interrupt if enabled.
Note:
With the exception of the HW_CFG, PMT_CTRL, BYTE_TEST, and
RESET_CTL registers, read access to any internal resources is
forbidden while the READY bit is cleared. Writes to any address
are invalid until this bit is set.
Note:
This bit is identical to bit 0 of the Power Management Control
Register (PMT_CTRL).
26
AMDIX_EN Strap State Port 2
This bit reflects the state of the auto_mdix_strap_2 strap that connects to
the PHY. The strap value is loaded with the level of the auto_mdix_strap_2
during reset and can be re-written by the EEPROM Loader. The strap value
can be overridden by bit 15 and 13 of the Port 2 PHY Special Control/Status
Indication Register (Section 14.4.2.10).
RO
Note 14.47
25
AMDIX_EN Strap State Port 1
This bit reflects the state of the auto_mdix_strap_1 strap that connects to
the PHY. The strap value is loaded with the level of the auto_mdix_strap_1
during reset and can be re-written by the EEPROM Loader. The strap value
can be overridden by bit 15 and 13 of the Port 1 PHY Special Control/Status
Indication Register (Section 14.4.2.10).
RO
Note 14.48
RESERVED
RO
-
21
RESERVED - This bit must be written with 0b for proper operation.
R/W
0b
20
Must Be One (MBO). This bit must be set to ‘1’ for normal device operation.
R/W
0b
24:22
SMSC LAN9312
261
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
19:16
TX FIFO Size (TX_FIF_SZ)
This field sets the size of the TX FIFOs in 1KB values to a maximum of
14KB. The TX Status FIFO consumes 512 bytes of the space allocated by
TX_FIF_SIZ, and the TX Data FIFO consumes the remaining space
specified by TX_FIF_SZ. The minimum size of the TX FIFOs is 2KB (TX
Data FIFO and Status FIFO combined). The TX Data FIFO is used for both
TX data and TX commands.
R/W
5h
The RX Status and Data FIFOs consume the remaining space, which is
equal to 16KB minus TX_FIF_SIZ. See section Section 9.7.3, "FIFO
Memory Allocation Configuration," on page 121 for more information.
15:14
RESERVED
RO
-
13:12
RESERVED - This field must be written with 00b for proper operation.
R/W
00b
RESERVED
RO
-
Soft Reset (SRST)
Writing 1 generates a software initiated reset to the Host Bus Interface, the
Host MAC, and System CSR’s below address 100h. The System CSR’s are
all reset except for any NASR bits. Soft reset also clears any TX or RX
errors in the Host MAC transmitter and receiver (TXE/RXE). This bit is selfclearing. In order to reset all values, the Reset Control Register
(RESET_CTL) must be used.
R/W
SC
0b
11:1
0
Note:
This bit will read high during assertion of DIGITAL_RST in the
Reset Control Register (RESET_CTL). The LAN9312 must always
be read at least once after power-up or reset to ensure that write
operations function correctly.
Note 14.47 The default value of this field is determined by the configuration strap auto_mdix_strap_2.
See Section 4.2.4, "Configuration Straps," on page 40 for more information.
Note 14.48 The default value of this field is determined by the configuration strap auto_mdix_strap_1.
See Section 4.2.4, "Configuration Straps," on page 40 for more information.
Revision 2.0 (02-14-13)
262
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.9.4
Power Management Control Register (PMT_CTRL)
Offset:
084h
Size:
32 bits
This read-write register controls the power management features and the PME pin of the LAN9312.
The ready state of the LAN9312 can be determined via the Device Ready (READY) bit of this register.
Refer to Section 4.3, "Power Management," on page 46 for additional information.
Note: This register is one of only four registers (the others are HW_CFG, BYTE_TEST, and
RESET_CTL) which can be polled while the LAN9312 is in the reset or not ready state (READY
bit is cleared).
BITS
TYPE
DEFAULT
RO
-
R/WC
0b
R/WC
0b
R/W
0b
R/W
0b
RESERVED
RO
-
10
Virtual PHY Reset (VPHY_RST)
Writing a 1 to this bit resets the Virtual PHY. When the Virtual PHY is
released from reset, this bit is automatically cleared. All writes to this bit are
ignored while this bit is high.
R/W
SC
0b
9
Wake-On-LAN Enable (WOL_EN)
When set, the PME signal (if enabled via the PME_EN bit) will be asserted
in accordance with the PME_IND bit upon a WOL event. When set, the
PME_INT bit in the Interrupt Status Register (INT_STS) will also be asserted
upon a WOL event, regardless of the setting of the PME_EN bit.
R/W
0b
31:18
17
DESCRIPTION
RESERVED
Energy-Detect Status Port 2 (ED_STS2)
This bit indicates an energy detect event occurred on the Port 2 PHY.
In order to clear this bit, it is required that the event in the PHY be cleared
as well. The event sources are described in Section 4.3, "Power
Management," on page 46.
16
Energy-Detect Status Port 1 (ED_STS1)
This bit indicates an energy detect event occurred on the Port 1 PHY.
In order to clear this bit, it is required that the event in the PHY be cleared
as well. The event sources are described in Section 4.3, "Power
Management," on page 46.
15
Energy-Detect Enable Port 2 (ED_EN2)
When set, the PME signal (if enabled via the PME_EN bit) will be asserted
in accordance with the PME_IND bit upon an energy-detect event from Port
2. When set, the PME_INT bit in the Interrupt Status Register (INT_STS) will
also be asserted upon an energy-detect event from Port 2, regardless of the
setting of the PME_EN bit.
Note:
14
Energy-Detect Enable Port 1 (ED_EN1)
When set, the PME signal (if enabled via the PME_EN bit) will be asserted
in accordance with the PME_IND bit upon an energy-detect event from Port
1. When set, the PME_INT bit in the Interrupt Status Register (INT_STS) will
also be asserted upon an energy-detect event from Port 1, regardless of the
setting of the PME_EN bit.
Note:
13:11
The EDPWRDOWN bit of the Port x PHY Mode Control/Status
Register (PHY_MODE_CONTROL_STATUS_x) of the Port 2 PHY
must also be set to enable the energy detect feature.
SMSC LAN9312
The EDPWRDOWN bit in the Port x PHY Mode Control/Status
Register (PHY_MODE_CONTROL_STATUS_x) of the Port 1 PHY
must also be set to enable the energy detect feature.
263
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
8:7
6
DESCRIPTION
RESERVED
PME Buffer Type (PME_TYPE)
When this bit is cleared, the PME pin functions as an open-drain buffer for
use in a wired-or configuration. When set, the PME pin is a push-pull driver.
TYPE
DEFAULT
RO
-
R/W
NASR
0b
R/WC
0b
Note:
When PME is configured as an open-drain output, the PME_POL
field of this register is ignored and the output is always active low.
0: PME pin open-drain output
1: PME pin push-pull driver
5
Wake On LAN Status (WOL_STS)
This bit indicates that a wake-up frame or magic packet was detected by the
Host MAC.
In order to clear this bit, it is required that the event in the Host MAC be
cleared as well. The event sources are described in Section 4.3, "Power
Management," on page 46.
4
RESERVED
RO
-
3
PME Indication (PME_IND)
The PME signal can be configured as a pulsed output or a static signal,
which is asserted upon detection of a wake-up event. When set, the PME
signal will pulse active for 50mS upon detection of a wake-up event. When
cleared, the PME signal is driven continuously upon detection of a wake-up
event.
R/W
0b
R/W
NASR
0b
R/W
0b
0: PME 50mS pulse on detection of event
1: PME driven continuously on detection of event
The PME signal can be deactivated by clearing the WOL_STS bit or by
clearing the appropriate enable.
2
PME Polarity (PME_POL)
This bit controls the polarity of the PME signal. When set, the PME output
is an active high signal. When cleared, it is active low.
Note:
When PME is configured as an open-drain output, this field is
ignored and the output is always active low.
0: PME active low
1: PME active high
1
PME Enable (PME_EN)
When set, this bit enables the external PME signal pin. When cleared, the
external PME signal is disabled.
Note:
This bit does not affect the PME_INT interrupt bit of the Interrupt
Status Register (INT_STS).
0: PME pin disabled
1: PME pin enabled
Revision 2.0 (02-14-13)
264
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
0
Device Ready (READY)
When set, this bit indicates that the LAN9312 is ready to be accessed. Upon
power-up, nRST reset, soft reset, or digital reset, the host processor may
interrogate this field as an indication that the LAN9312 has stabilized and is
fully active.
RO
0b
This bit can cause an interrupt if enabled.
Note:
With the exception of the HW_CFG, PMT_CTRL, BYTE_TEST, and
RESET_CTL registers, read access to any internal resources is
forbidden while the READY bit is cleared. Writes to any address
are invalid until this bit is set.
Note:
This bit is identical to bit 27 of the Hardware Configuration Register
(HW_CFG).
SMSC LAN9312
265
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.9.5
General Purpose Timer Configuration Register (GPT_CFG)
Offset:
08Ch
Size:
32 bits
This read/write register configures the LAN9312 General Purpose Timer (GPT). The GPT can be
configured to generate host interrupts at the interval defined in this register. The current value of the
GPT can be monitored via the General Purpose Timer Count Register (GPT_CNT). Refer to Section
12.1, "General Purpose Timer," on page 161 for additional information.
BITS
31:30
29
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
General Purpose Timer Enable (TIMER_EN)
This bit enables the GPT. When set, the GPT enters the run state. When
cleared, the GPT is halted. On the 1 to 0 transition of this bit, the
GPT_LOAD field of this register will be preset to FFFFh.
R/W
0b
0: GPT Disabled
1: GPT Enabled
28:16
RESERVED
RO
-
15:0
General Purpose TImer Pre-Load (GPT_LOAD)
This value is pre-loaded into the GPT. This is the starting value of the GPT.
The timer will begin decrementing from this value when enabled.
R/W
FFFFh
Revision 2.0 (02-14-13)
266
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.9.6
General Purpose Timer Count Register (GPT_CNT)
Offset:
090h
Size:
32 bits
This read-only register reflects the current general purpose timer (GPT) value. The register should be
used in conjunction with the General Purpose Timer Configuration Register (GPT_CFG) to configure
and monitor the GPT. Refer to Section 12.1, "General Purpose Timer," on page 161 for additional
information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:0
General Purpose Timer Current Count (GPT_CNT)
This 16-bit field represents the current value of the GPT.
RO
FFFFh
SMSC LAN9312
267
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.9.7
Free Running 25MHz Counter Register (FREE_RUN)
Offset:
09Ch
Size:
32 bits
This read-only register reflects the current value of the free-running 25MHz counter. Refer to Section
12.2, "Free-Running Clock," on page 161 for additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Free Running Counter (FR_CNT)
This field reflects the current value of the free-running 32-bit counter. At
reset, the counter starts at zero and is incremented by one every 25MHz
cycle. When the maximum count has been reached, the counter will rollover
to zero and continue counting.
RO
00000000h
Note:
The free running counter can take up to 160nS to clear after a reset
event.
Revision 2.0 (02-14-13)
268
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.2.9.8
Reset Control Register (RESET_CTL)
Offset:
1F8h
Size:
32 bits
This register contains software controlled resets.
Note: This register can be read while the LAN9312 is in the reset or not ready states.
BITS
31:4
3
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Virtual PHY Reset (VPHY_RST)
Setting this bit resets the Virtual PHY. When the Virtual PHY is released from
reset, this bit is automatically cleared. All writes to this bit are ignored while
this bit is set.
R/W
SC
0b
R/W
SC
0b
R/W
SC
0b
R/W
SC
0b
Note:
2
Port 2 PHY Reset (PHY2_RST)
Setting this bit resets the Port 2 PHY. The internal logic automatically holds
the PHY reset for a minimum of 102uS. When the Port 2 PHY is released
from reset, this bit is automatically cleared. All writes to this bit are ignored
while this bit is set.
Note:
1
This bit is not accessible via the EEPROM Loader.
Port 1 PHY Reset (PHY1_RST)
Setting this bit resets the Port 1 PHY. The internal logic automatically holds
the PHY reset for a minimum of 102uS. When the Port 1 PHY is released
from reset, this bit is automatically cleared. All writes to this bit are ignored
while this bit is set.
Note:
0
This bit is not accessible via the EEPROM Loader.
This bit is not accessible via the EEPROM Loader.
Digital Reset (DIGITAL_RST)
Setting this bit resets the complete chip except the PLL, Virtual PHY, Port 1
PHY, and Port 2 PHY. The EEPROM Loader will automatically reload the
configuration following this reset, but will not reset the Virtual PHY, Port 1
PHY, or Port 2 PHY. If desired, the above PHY resets can be issued once
the device is configured. All system CSRs are reset except for any NASR
type bits. Any in progress EEPROM commands (including RELOAD) are
terminated.
When the chip is released from reset, this bit is automatically cleared. This
bit should be polled to determine when the reset is complete. All writes to
this bit are ignored while this bit is set.
Note:
The LAN9312must always be read at least once after power-up or
reset to ensure that write operations function properly.
Note:
This bit is not accessible via the EEPROM Loader.
SMSC LAN9312
269
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3
Host MAC Control and Status Registers
This section details the Host MAC System CSR’s. These registers are located in the Host MAC and
are accessed indirectly via the HBI system CSR’s. Table 14.6 lists Host MAC registers that are
accessible through the indexing method using the Host MAC CSR Interface Command Register
(MAC_CSR_CMD) and Host MAC CSR Interface Data Register (MAC_CSR_DATA).
The Host MAC registers allow configuration of the various Host MAC parameters including the Host
MAC address, flow control, multicast hash table, and wake-up configuration. The Host MAC CSR’s
also provide serial access to the PHYs via the registers HMAC_MII_ACC and HMAC_MII_DATA.
These registers allow access to the 10/100 Ethernet PHY registers and the switch engine (via Port 0).
Table 14.6 Host MAC Adressable Registers
INDEX #
SYMBOL
00h
RESERVED
Reserved for Future Use
01h
HMAC_CR
Host MAC Control Register, Section 14.3.1
02h
HMAC_ADDRH
Host MAC Address High Register, Section 14.3.2
03h
HMAC_ADDRL
Host MAC Address Low Register, Section 14.3.3
04h
HMAC_HASHH
Host MAC Multicast Hash Table High Register, Section 14.3.4
05h
HMAC_HASHL
Host MAC Multicast Hash Table Low Register, Section 14.3.5
06h
HMAC_MII_ACC
Host MAC MII Access Register, Section 14.3.6
07h
HMAC_MII_DATA
Host MAC MII Data Register, Section 14.3.7
08h
HMAC_FLOW
Host MAC Flow Control Register, Section 14.3.8
09h
HMAC_VLAN1
Host MAC VLAN1 Tag Register, Section 14.3.9
0Ah
HMAC_VLAN2
Host MAC VLAN2 Tag Register, Section 14.3.10
0Bh
HMAC_WUFF
Host MAC Wake-up Frame Filter Register, Section 14.3.11
0Ch
HMAC_WUCSR
0Dh-FFh
RESERVED
Revision 2.0 (02-14-13)
REGISTER NAME
Host MAC Wake-up Control and Status Register,
Section 14.3.12
Reserved for Future Use
270
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.1
Host MAC Control Register (HMAC_CR)
Offset:
1h
Size:
32 bits
This read/write register establishes the RX and TX operation modes and controls for address filtering
and packet filtering. Refer to Chapter 9, "Host MAC," on page 112 for additional information.
Bits 19-15, 13, and 11 determine if the Host MAC accepts the packets from the switch fabric. The
switch fabric address table and configuration determine which packets get sent to the Host MAC.
BITS
DESCRIPTION
TYPE
DEFAULT
31
Receive All Mode (RXALL)
When set, all incoming packets will be received and passed on to the
address filtering function for processing of the selected filtering mode on the
received frame. Address filtering then occurs and is reported in Receive
Status. When cleared, only frames that pass Destination Address filtering
will be sent to the application.
R/W
0b
RESERVED
RO
-
23
Disable Receive Own (RCVOWN)
When set, the Host MAC disables the reception of frames when TXEN (bit
3) is asserted. The Host MAC blocks the transmitted frame on the receive
path. When cleared, the Host MAC receives all packets, including those
transmitted by the Host MAC. This bit should be cleared when the Full
Duplex Mode bit is set.
R/W
0b
22
RESERVED
RO
-
21
Loopback operation Mode (LOOPBK)
Selects the loop back operation modes for the Host MAC. This field is only
valid for full duplex mode. In internal loopback mode, the TX frame is
received by the internal MII interface, and sent back to the Host MAC
without being sent to the switch fabric.
R/W
0b
30:24
0: Normal Operation. Loopback disabled.
1: Loopback enabled
Note:
When enabling or disabling the loopback mode it can take up to
10μs for the mode change to occur. The transmitter and receiver
must be stopped and disabled when modifying the LOOPBK bit.
The transmitter or receiver should not be enabled within10μs of
modifying the LOOPBK bit.
20
Full Duplex Mode (FDPX)
When set, the Host MAC operates in Full-Duplex mode, in which it can
transmit and receive simultaneously.
R/W
0b
19
Pass All Multicast (MCPAS)
When set, indicates that all incoming frames with a Multicast destination
address (first bit in the destination address field is 1) are received. Incoming
frames with physical address (Individual Address/Unicast) destinations are
filtered and received only if the address matches the Host MAC Address.
R/W
0b
18
Promiscuous Mode (PRMS)
When set, indicates that any incoming frame is received regardless of its
destination address.
R/W
1b
17
Inverse filtering (INVFILT)
When set, the address check function operates in inverse filtering mode.
This is valid only during Perfect filtering mode. Refer to Section 9.4.4,
"Inverse Filtering," on page 116 for additional information.
R/W
0b
SMSC LAN9312
271
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
16
Pass Bad Frames (PASSBAD)
When set, all incoming frames that passed address filtering are received,
including runt frames and collided frames. Refer to Section 9.4, "Address
Filtering," on page 114 for additional information.
R/W
0b
15
Hash Only Filtering mode (HO)
When set, the address check Function operates in the Imperfect address
filtering mode for both physical and multicast addresses. Refer to Section
9.4.2, "Hash Only Filtering," on page 115 for additional information.
R/W
0b
14
RESERVED
RO
-
13
Hash/Perfect Filtering Mode (HPFILT)
When cleared (0), the LAN9312 will implement a perfect address filter on
incoming frames according the address specified in the Host MAC address
registers (Host MAC Address High Register (HMAC_ADDRH) and Host
MAC Address Low Register (HMAC_ADDRL)).
R/W
0b
When set (1), the address check function performs imperfect address
filtering of multicast incoming frames according to the hash table specified
in the multicast hash table register. If the Hash Only Filtering mode (HO) bit
15 is set, then the physical (IA) addresses are also imperfect filtered. If the
Hash Only Filtering mode (HO) bit is cleared, then the IA addresses are
perfect address filtered according to the MAC Address register Refer to
Section 9.4.3, "Hash Perfect Filtering," on page 115 for additional
information.
12
RESERVED
RO
-
11
Disable Broadcast Frames (BCAST)
When set, disables the reception of broadcast frames. When cleared,
forwards all broadcast frames to the application.
R/W
0b
Note:
When wake-up frame detection is enabled via the WUEN bit of the
Host MAC Wake-up Control and Status Register (HMAC_WUCSR),
a broadcast wake-up frame will wake-up the device despite the
state of this bit.
10
Disable Retry (DISRTY)
When set, the Host MAC attempts only one transmission. When a collision
is seen on the bus, the Host MAC ignores the current frame and goes to the
next frame and a retry error is reported in the Transmit status. When reset,
the Host MAC attempts 16 transmissions before signaling a retry error.
R/W
0b
9
RESERVED
RO
-
8
Automatic Pad Stripping (PADSTR)
When set, the Host MAC strips the pad field on all incoming frames, if the
length field is less than 46 bytes. The FCS field is also stripped, since it is
computed at the transmitting station based on the data and pad field
characters, and is invalid for a received frame that has had the pad
characters stripped. Receive frames with a 46-byte or greater length field
are passed to the application unmodified (FCS is not stripped). When
cleared, the Host MAC passes all incoming frames to the host unmodified.
R/W
0b
Revision 2.0 (02-14-13)
272
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
7:6
BackOff Limit (BOLMT)
The BOLMT bits allow the user to set the back-off limit in a relaxed or
aggressive mode. According to IEEE 802.3, the Host MAC has to wait for a
random number [r] of slot-times(see note) after it detects a collision, where:
(eq.1)0 < r < 2K
The exponent K is dependent on how many times the current frame to be
transmitted has been retried, as follows:
(eq.2)K = min (n, 10) where n is the current number of retries.
If a frame has been retried three times, then K = 3 and r= 8 slot-times
maximum. If it has been retried 12 times, then K = 10, and r = 1024 slottimes maximum.
An LFSR (linear feedback shift register) 20-bit counter emulates a 20 bit
random number generator, from which r is obtained. Once a collision is
detected, the number of the current retry of the current frame is used to
obtain K (eq.2). This value of K translates into the number of bits to use from
the LFSR counter. If the value of K is 3, the Host MAC takes the value in
the first three bits of the LFSR counter and uses it to count down to zero on
every slot-time. This effectively causes the Host MAC to wait eight slottimes. To give the user more flexibility, the BOLMT value forces the number
of bits to be used from the LFSR counter to a predetermined value as in the
table below.
R/W
0b
BOLMT Value
# Bits Used from LFSR Counter
00b
10
01b
8
10b
4
11b
1
Thus, if the value of K = 10, the Host MAC will look at the BOLMT if it is 00b,
then use the lower ten bits of the LFSR counter for the wait countdown. If the BOLMT
is 10b, then it will only use the value in the first four bits for the wait countdown,
etc.
Note:
Slot-time = 512 bit times. (See IEEE 802.3 Spec., sections 4.2.3.25
and 4.4.2.1)
5
Deferral Check (DFCHK)
When set, enables the deferral check in the Host MAC. The Host MAC will
abort the transmission attempt if it has deferred for more than 24,288 bit
times. Deferral starts when the transmitter is ready to transmit, but is
prevented from doing so because the CRS is active. Deferral time is not
cumulative. If the transmitter defers for 10,000 bit times, then transmits,
collides, backs off, and then has to defer again after completion of back-off,
the deferral timer resets to 0 and restarts. When this bit is cleared, the
deferral check is disabled in the Host MAC and the Host MAC defers
indefinitely.
R/W
0b
4
RESERVED
RO
-
3
Transmitter enable (TXEN)
When set, the Host MAC’s transmitter is enabled and it will transmit frames
from the buffer.
When cleared, the Host MAC’s transmitter is disabled and will not transmit
any frames.
R/W
0b
2
Receiver Enable (RXEN)
When set, the Host MAC’s receiver is enabled and will receive frames.
When cleared, the MAC’s receiver is disabled and will not receive any
frames.
R/W
0b
RESERVED
RO
-
1:0
SMSC LAN9312
273
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.2
Host MAC Address High Register (HMAC_ADDRH)
Offset:
2h
Size:
32 bits
This read/write register contains the upper 16-bits of the physical address of the Host MAC. The
contents of this register are optionally loaded from the EEPROM at power-on through the EEPROM
Loader if a programmed EEPROM is detected. The least significant byte of this register (bits [7:0]) is
loaded from address 05h of the EEPROM. The second byte (bits [15:8]) is loaded from address 06h
of the EEPROM. Section 9.6, "Host MAC Address," on page 119 details the byte ordering of the
HMAC_ADDRL and HMAC_ADDRH registers with respect to the reception of the Ethernet physical
address. Please refer to Section 10.2, "I2C/Microwire Master EEPROM Controller," on page 137 for
more information on the EEPROM Loader.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:0
Physical Address [47:32]
This field contains the upper 16-bits (47:32) of the Physical Address of the
Host MAC. The content of this field is undefined until loaded from the
EEPROM at power-on. The host can update the contents of this field after
the initialization process has completed.
R/W
FFFFh
Revision 2.0 (02-14-13)
274
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.3
Host MAC Address Low Register (HMAC_ADDRL)
Offset:
3h
Size:
32 bits
This read/write register contains the lower 32-bits of the physical address of the Host MAC. The
contents of this register are optionally loaded from the EEPROM at power-on through the EEPROM
Loader if a programmed EEPROM is detected. The least significant byte of this register (bits [7:0]) is
loaded from address 01h of the EEPROM. The most significant byte of this register is loaded from
address 04h of the EEPROM. Section 9.6, "Host MAC Address," on page 119 details the byte ordering
of the HMAC_ADDRL and HMAC_ADDRH registers with respect to the reception of the Ethernet
physical address. Please refer to Section 10.2, "I2C/Microwire Master EEPROM Controller," on
page 137 for more information on the EEPROM Loader.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Physical Address [31:0]
This field contains the lower 32-bits (31:0) of the Physical Address of the
Host MAC. The content of this field is undefined until loaded from the
EEPROM at power-on. The host can update the contents of this field after
the initialization process has completed.
R/W
FFFFFFFFh
SMSC LAN9312
275
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.4
Host MAC Multicast Hash Table High Register (HMAC_HASHH)
Offset:
4h
Size:
32 bits
The 64-bit Multicast table is used for group address filtering. For hash filtering, the contents of the
destination address in the incoming frame is used to index the contents of the Hash table. The most
significant bit determines the register to be used (Hi/Low), while the other five bits determine the bit
within the register. A value of 00000 selects Bit 0 of the Multicast Hash Table Lo register and a value
of 11111 selects the Bit 31 of the Multicast Hash Table Hi register.
If the corresponding bit is 1, then the multicast frame is accepted. Otherwise, it is rejected. If the “Pass All
Multicast” (MCPAS) bit of the Host MAC Control Register (HMAC_CR) is set, then all multicast frames are
accepted regardless of the multicast hash values.
The Multicast Hash Table High register contains the higher 32 bits of the hash table and the Multicast
Hash Table Low register contains the lower 32 bits of the hash table. Refer to Section 9.4, "Address
Filtering," on page 114 for more information on address filtering.
This table determines if the Host MAC accepts the packets from the switch fabric. The switch fabric
address table and configuration determine the packets that get sent to the Host MAC.
BITS
31:0
DESCRIPTION
Upper 32-bits of the 64-bit Hash Table
Revision 2.0 (02-14-13)
276
DATASHEET
TYPE
DEFAULT
R/W
00000000h
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.5
Host MAC Multicast Hash Table Low Register (HMAC_HASHL)
Offset:
5h
Size:
32 bits
This read/write register defines the lower 32-bits of the Multicast Hash Table. Please refer to the Host
MAC Multicast Hash Table High Register (HMAC_HASHH) and Section 9.4, "Address Filtering" for
more information.
BITS
31:0
DESCRIPTION
Lower 32-bits of the 64-bit Hash Table
SMSC LAN9312
277
DATASHEET
TYPE
DEFAULT
R/W
00000000h
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.6
Host MAC MII Access Register (HMAC_MII_ACC)
Offset:
6h
Size:
32 bits
This read/write register is used in conjunction with the Host MAC MII Data Register (HMAC_MII_DATA)
to access the internal PHY registers. Refer to Section 14.4, "Ethernet PHY Control and Status
Registers" for a list of accessible PHY registers and PHY address information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:11
PHY Address (PHY_ADDR)
This field must be loaded with the PHY address that the MII access is
intended for. A list default PHY addresses can be seen in Table 7.1. Refer
to Section 7.1.1, "PHY Addressing," on page 82 for additional information on
PHY addressing.
R/W
00000b
10:6
MII Register Index (MIIRINDA)
These bits select the desired MII register in the PHY.
R/W
00000b
5:2
RESERVED
RO
-
1
MII Write (MIIWnR)
Setting this bit tells the PHY that this will be a write operation using the Host
MAC MII Data Register (HMAC_MII_DATA). If this bit is cleared, a read
operation will occur, packing the data in the Host MAC MII Data Register
(HMAC_MII_DATA).
R/W
0b
0
MII Busy (MIIBZY)
This bit must be polled to determine when the MII register access is
complete. This bit must read a logical 0 before writing to this register or the
Host MAC MII Data Register (HMAC_MII_DATA).
RO
SC
0b
The LAN driver software must set this bit in order for the
LAN9312 to read or write any of the MII PHY registers.
During a MII register access, this bit will be set, signifying a read or write
access is in progress. The MII data register must be kept valid until the Host
MAC clears this bit during a PHY write operation. The MII data register is
invalid until the Host MAC has cleared this bit during a PHY read operation.
Revision 2.0 (02-14-13)
278
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.7
Host MAC MII Data Register (HMAC_MII_DATA)
Offset:
7h
Size:
32 bits
This read/write register is used in conjunction with the Host MAC MII Access Register
(HMAC_MII_ACC) to access the internal PHY registers. This register contains either the data to be
written to the PHY register specified in the HMAC_MII_ACC Register, or the read data from the PHY
register whose index is specified in the HMAC_MII_ACC Register.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:0
MII Data
This field contains the 16-bit value read from the PHY read operation or the
16-bit data value to be written to the PHY before an MII write operation.
R/W
0000h
SMSC LAN9312
279
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.8
Host MAC Flow Control Register (HMAC_FLOW)
Offset:
8h
Size:
32 bits
This read/write register controls the generation and reception of the Control (Pause command) frames
by the Host MAC’s flow control block. The control frame fields are selected as specified in the 802.3
Specification and the Pause-Time value from this register is used in the “Pause Time” field of the
control frame. In full-duplex mode the FCBSY bit is set until the control frame is completely transferred.
In half-duplex mode FCBSY is set while back pressure is being asserted. The host has to make sure
that the FCBSY bit is cleared before writing the register. The Pass Control Frame bit (FCPASS) does
not affect the sending of the frames, including Control Frames, to the host. The Flow Control Enable
(FCEN) bit enables the receive portion of the Flow Control block.
This register is used in conjunction with the Host MAC Automatic Flow Control Configuration Register
(AFC_CFG) in the System CSR’s to configure flow control. Software flow control is initiated using the
AFC_CFG register.
Note: The Host MAC will not transmit pause frames or assert back pressure if the transmitter is
disabled.
Note: For the Host MAC, flow control/backpressure is to/from the switch fabric, not the external
network.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
Pause Time (FCPT)
This field indicates the value to be used in the PAUSE TIME field in the
control frame. This field must be initialized before full-duplex automatic flow
control is enabled.
R/W
0000h
15:3
RESERVED
RO
-
Pass Control Frames (FCPASS)
When set, the Host MAC sets the packet filter bit in the receive packet status
to indicate to the application that a valid pause frame has been received.
The application must accept or discard a received frame based on the
packet filter control bit. The Host MAC receives, decodes and performs the
Pause function when a valid Pause frame is received in Full-Duplex mode
and when flow control is enabled (FCE bit set). When this bit is cleared, the
Host MAC resets the Packet Filter bit in the Receive packet status.
R/W
0b
R/W
0b
2
The Host MAC always passes the data of all frames it receives (including
flow control frames) to the application. Frames that do not pass address
filtering, as well as frames with errors, are passed to the application. The
application must discard or retain the received frame’s data based on the
received frame’s STATUS field. Filtering modes (promiscuous mode, for
example) take precedence over the FCPASS bit.
1
Flow Control Enable (FCEN)
When set, enables the Host MAC flow control function. The Host MAC
decodes all incoming frames for control frames; if it receives a valid control
frame (PAUSE command), it disables the transmitter for a specified time
(Decoded pause time x slot time). When this bit is cleared, the Host MAC
flow control function is disabled; the MAC does not decode frames for
control frames.
Note:
Flow Control is applicable when the Host MAC is set in full duplex
mode. In half-duplex mode, this bit enables the backpressure
function to control the flow of received frames to the Host MAC.
Revision 2.0 (02-14-13)
280
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
0
Flow Control Busy (FCBSY)
In full-duplex mode, this bit should read logical 0 before writing to the Host
MAC Flow Control (HMAC_FLOW) register. To initiate a PAUSE control
frame, the bit must be set. During a transfer of control frame, this bit
continues to be set, signifying that a frame transmission is in progress. After
the PAUSE control frame’s transmission is complete, the Host MAC resets
the bit to 0.
R/W
0b
Backpressure Enable (BkPresEn)
In half-duplex mode, this signal functions as a backpressure enable and is
set high whenever backpressure is transmitted.
Notes:
 When writing this register, the FCBSY bit must always be zero.
 Applications must always write a zero to this bit
SMSC LAN9312
281
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.9
Host MAC VLAN1 Tag Register (HMAC_VLAN1)
Offset:
9h
Size:
32 bits
This read/write register contains the VLAN tag field to identify VLAN1 frames. When a VLAN1 frame
is detected, the legal frame length is increased from 1518 bytes to 1522 bytes. Refer to Section 9.3,
"Virtual Local Area Network (VLAN) Support," on page 113 for additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:0
VLAN1 Tag Identifier (VTI1)
This field contains the VLAN Tag used to identify VLAN1 frames. This field
is compared with the 13th and 14th bytes of the incoming frames for VLAN1
frame detection.
R/W
FFFFh
Note:
If used, this register is typically set to the standard VLAN value of
8100h.
Revision 2.0 (02-14-13)
282
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.10
Host MAC VLAN2 Tag Register (HMAC_VLAN2)
Offset:
Ah
Size:
32 bits
This read/write register contains the VLAN tag field to identify VLAN2 frames. When a VLAN2 frame
is detected, the legal frame length is increased from 1518 bytes to 1538 bytes. Refer to Section 9.3,
"Virtual Local Area Network (VLAN) Support," on page 113 for additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:0
VLAN2 Tag Identifier (VTI2)
This field contains the VLAN Tag used to identify VLAN2 frames. This field
is compared with the 13th and 14th bytes of the incoming frames for VLAN2
frame detection.
R/W
FFFFh
Note:
SMSC LAN9312
If used, this register is typically set to the standard VLAN value of
8100h. If both VLAN1 and VLAN2 Tag Identifiers are used, they
should be unique. If both are set to the same value, VLAN1 is
given higher precedence and the maximum legal frame length is
set to 1522.
283
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.11
Host MAC Wake-up Frame Filter Register (HMAC_WUFF)
Offset:
Bh
Size:
32 bits
This write-only register is used to configure the wake-up frame filter. Refer to Section 9.5, "Wake-up
Frame Detection," on page 116 for additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Wake-Up Frame Filter (WFF)
The Wake-up frame filter is configured through this register using an
indexing mechanism. After power-on reset, digital reset, or soft reset, the
Host MAC loads the first value written to this location to the first DWORD in
the Wake-up frame filter (filter 0 byte mask). The second value written to this
location is loaded to the second DWORD in the wake-up frame filter (filter 1
byte mask) and so on. Once all eight DWORD’s have been written, the
internal pointer will once again point to the first entry and the filter entries
can be modified in the same manner.
WO
-
Note:
This is a write-only register.
Revision 2.0 (02-14-13)
284
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.3.12
Host MAC Wake-up Control and Status Register (HMAC_WUCSR)
Offset:
Ch
Size:
32 bits
This read/write register contains data and control settings pertaining to the Host MAC’s remote wakeup status and capabilities. It is used in conjunction with the Host MAC Wake-up Frame Filter Register
(HMAC_WUFF) to fully configure the wake-up frame filter. Refer to Section 9.5, "Wake-up Frame
Detection," on page 116 for additional information.
BITS
31:10
9
8:7
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Global Unicast Enable (GUE)
When set, the Host MAC wakes up from power-saving mode on receipt of
a global unicast frame. This is accomplished by enabling global unicasts as
a wakeup frame qualifier. A global unicast frame has the MAC Address [0]
bits set to 0.
R/W
0b
RESERVED
RO
-
6
Remote Wake-Up Frame Received (WUFR)
The Host MAC sets this bit upon receiving a valid Remote Wake-up frame.
R/WC
0b
5
Magic Packet Received (MPR)
The Host MAC sets this bit upon receiving a valid Magic Packet
R/WC
0b
RESERVED
RO
-
2
Wake-Up Frame enabled (WUEN)
When set, Remote Wake-Up mode is enabled and the Host MAC is capable
of detecting wake-up frames as programmed in the Host MAC Wake-up
Frame Filter Register (HMAC_WUFF).
R/W
0b
1
Magic Packet Enable (MPEN)
When set, Magic Packet Wake-up mode is enabled.
R/W
0b
0
RESERVED
RO
-
4-3
SMSC LAN9312
285
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4
Ethernet PHY Control and Status Registers
This section details the various LAN9312 Ethernet PHY control and status registers. The LAN9312
contains three PHY’s: Port 1 PHY, Port 2 PHY and a Virtual PHY. All PHY registers follow the IEEE
802.3 (clause 22.2.4) specified MII management register set. All functionality and bit definitions comply
with these standards. The IEEE 802.3 specified register index (in decimal) is included with each
register definition, allowing for addressing of these registers via the MII serial management protocol.
For additional information on the MII management protocol, refer to the IEEE 802.3 Specification.
Each individual PHY is assigned a unique PHY address as detailed in Section 7.1.1, "PHY
Addressing," on page 82.
14.4.1
Virtual PHY Registers
The Virtual PHY provides a basic MII management interface for communication with the Host MAC for
connection to the Host as if it was attached to a single port PHY. The Virtual PHY registers differ from
the Port 1 & 2 PHY registers in that they are addressable via the memory map, as described in
Table 14.1, as well as serially. These modes of access are described in Section 14.2.8, "Virtual PHY,"
on page 245.
Because the Virtual PHY registers are also memory mapped, their definitions have been included in
the System Control and Status Registers Section 14.2.8, "Virtual PHY," on page 245. A list of the Virtual
PHY MII addressable registers and their corresponding register index numbers is also included in
Table 14.4.
Note: When serially accessed, the Virtual PHY registers are only 16-bits wide, as is standard for MII
management of PHY’s.
14.4.2
Port 1 & 2 PHY Registers
The Port 1 and Port 2 PHY’s are comparable in functionality and have an identical set of non-memory
mapped registers. The Port 1 and Port 2 PHY registers are not memory mapped. These registers are
indirectly accessed through the Host MAC MII Access Register (HMAC_MII_ACC) and Host MAC MII
Data Register (HMAC_MII_DATA) registers in the Host MAC via the MII serial management protocol
specified in IEEE 802.3 clause 22. Because the Port 1 & 2 PHY registers are functionally identical,
their register descriptions have been consolidated. A lowercase “x” has been appended to the end of
each PHY register name in this section, where “x” should be replaced with “1” or “2” for the Port 1
PHY or the Port 2 PHY registers respectively. A list of the Port 1 & 2 PHY MII addressable registers
and their corresponding register index numbers is included in Table 14.7. Each individual PHY is
assigned a unique PHY address as detailed in Section 7.1.1, "PHY Addressing," on page 82.
Table 14.7 Port 1 & 2 PHY MII Serially Adressable Registers
INDEX #
SYMBOL
0
PHY_BASIC_CONTROL_x
Port x PHY Basic Control Register, Section 14.4.2.1
1
PHY_BASIC_STATUS_x
Port x PHY Basic Status Register, Section 14.4.2.2
2
PHY_ID_MSB_x
Port x PHY Identification MSB Register, Section 14.4.2.3
3
PHY_ID_LSB_x
Port x PHY Identification LSB Register, Section 14.4.2.4
4
PHY_AN_ADV_x
Port x PHY Auto-Negotiation Advertisement Register,
Section 14.4.2.5
5
PHY_AN_LP_BASE_ABILITY_x
6
PHY_AN_EXP_x
Revision 2.0 (02-14-13)
REGISTER NAME
Port x PHY Auto-Negotiation Link Partner Base Page Ability
Register, Section 14.4.2.6
Port x PHY Auto-Negotiation Expansion Register,
Section 14.4.2.7
286
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.7 Port 1 & 2 PHY MII Serially Adressable Registers (continued)
INDEX #
SYMBOL
17
PHY_MODE_CONTROL_STATUS_x
Port x PHY Mode Control/Status Register, Section 14.4.2.8
18
PHY_SPECIAL_MODES_x
Port x PHY Special Modes Register, Section 14.4.2.9
27
PHY_SPECIAL_CONTROL_STAT_IND_x
Port x PHY Special Control/Status Indication Register,
Section 14.4.2.10
29
PHY_INTERRUPT_SOURCE_x
Port x PHY Interrupt Source Flags Register, Section 14.4.2.11
30
PHY_INTERRUPT_MASK_x
31
PHY_SPECIAL_CONTROL_STATUS_x
SMSC LAN9312
REGISTER NAME
Port x PHY Interrupt Mask Register, Section 14.4.2.12
Port x PHY Special Control/Status Register, Section 14.4.2.13
287
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.1
Port x PHY Basic Control Register (PHY_BASIC_CONTROL_x)
Index (decimal):
0
Size:
16 bits
This read/write register is used to configure the Port x PHY.
Note: This register is re-written in its entirety by the EEPROM Loader following the release of reset
or a RELOAD command. Refer to Section 10.2.4, "EEPROM Loader," on page 149 for
additional information.
BITS
DESCRIPTION
TYPE
DEFAULT
15
Reset (PHY_RST)
When set, this bit resets all the Port x PHY registers to their default state,
except those marked as NASR type. This bit is self clearing.
R/W
SC
0b
R/W
0b
R/W
Note 14.49
R/W
Note 14.50
R/W
0b
RO
-
0: Normal operation
1: Reset
14
Loopback (PHY_LOOPBACK)
This bit enables/disables the loopback mode. When enabled, transmissions
from the switch fabric are not sent to network. Instead, they are looped back
into the switch fabric.
Note:
If loopback is enabled during half-duplex operation, then the
Enable Receive Own Transmit bit in the Port x MAC Receive
Configuration Register (MAC_RX_CFG_x) must be set for the
specified port. Otherwise, the switch fabric will ignore receive
activity when transmitting in half-duplex mode.
0: Loopback mode disabled (normal operation)
1: Loopback mode enabled
13
Speed Select LSB (PHY_SPEED_SEL_LSB)
This bit is used to set the speed of the Port x PHY when the AutoNegotiation (PHY_AN) bit is disabled.
0: 10 Mbps
1: 100 Mbps
12
Auto-Negotiation (PHY_AN)
This bit enables/disables Auto-Negotiation. When enabled, the Speed Select
LSB (PHY_SPEED_SEL_LSB) and Duplex Mode (PHY_DUPLEX) bits are
overridden.
0: Auto-Negotiation disabled
1: Auto-Negotiation enabled
11
Power Down (PHY_PWR_DWN)
This bit controls the power down mode of the Port x PHY. After this bit is
cleared the PHY may auto-negotiate with it’s partner station. This process
can take up to a few seconds to complete. Once Auto-Negotiation is
complete, bit 5 (Auto-Negotiation Complete) of the Port x PHY Basic Status
Register (PHY_BASIC_STATUS_x) will be set.
Note:
The PHY_AN bit of this register must be cleared before setting this
bit.
0: Normal operation
1: General power down mode
10
RESERVED
Revision 2.0 (02-14-13)
288
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
9
DESCRIPTION
Restart Auto-Negotiation (PHY_RST_AN)
When set, this bit restarts the Auto-Negotiation process.
TYPE
DEFAULT
R/W
SC
0b
R/W
Note 14.51
R/W
0b
RO
-
0: Normal operation
1: Auto-Negotiation restarted
8
Duplex Mode (PHY_DUPLEX)
This bit is used to set the duplex when the Auto-Negotiation (PHY_AN) bit
is disabled.
0: Half Duplex
1: Full Duplex
7
Collision Test Mode (PHY_COL_TEST)
This bit enables/disables the collision test mode of the Port x PHY. When
set, the collision signal is active during transmission. It is recommended that
this feature be used only in loopback mode.
0: Collision test mode disabled
1: Collision test mode enabled
6:0
RESERVED
Note 14.49 The default value of this bit is determined by the logical OR of the Auto-Negotiation strap
(autoneg_strap_1 for Port 1 PHY, autoneg_strap_2 for Port 2 PHY) and the speed select
strap (speed_strap_1 for Port 1 PHY, speed_strap_2 for Port 2 PHY). Essentially, if the
Auto-Negotiation strap is set, the default value is 1, otherwise the default is determined by
the value of the speed select strap. Refer to Section 4.2.4, "Configuration Straps," on
page 40 for more information.
Note 14.50 The default value of this bit is determined by the value of the Auto-Negotiation strap
(autoneg_strap_1 for Port 1 PHY, autoneg_strap_2 for Port 2 PHY). Refer to Section 4.2.4,
"Configuration Straps," on page 40 for more information.
Note 14.51 The default value of this bit is determined by the logical AND of the negation of the AutoNegotiation strap (autoneg_strap_1 for Port 1 PHY, autoneg_strap_2 for Port 2 PHY) and
the duplex select strap (duplex_strap_1 for Port 1 PHY, duplex_strap_2 for Port 2 PHY).
Essentially, if the Auto-Negotiation strap is set, the default value is 0, otherwise the default
is determined by the value of the duplex select strap. Refer to Section 4.2.4, "Configuration
Straps," on page 40 for more information.
SMSC LAN9312
289
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.2
Port x PHY Basic Status Register (PHY_BASIC_STATUS_x)
Index (decimal):
1
Size:
16 bits
This register is used to monitor the status of the Port x PHY.
BITS
15
DESCRIPTION
TYPE
DEFAULT
RO
0b
Note 14.52
RO
1b
RO
1b
RO
1b
RO
1b
RO
0b
Note 14.52
RO
0b
Note 14.52
RESERVED
RO
-
Auto-Negotiation Complete
This bit indicates the status of the Auto-Negotiation process.
RO
0b
RO/LH
0b
100BASE-T4
This bit displays the status of 100BASE-T4 compatibility.
0: PHY not able to perform 100BASE-T4
1: PHY able to perform 100BASE-T4
14
100BASE-X Full Duplex
This bit displays the status of 100BASE-X full duplex compatibility.
0: PHY not able to perform 100BASE-X full duplex
1: PHY able to perform 100BASE-X full duplex
13
100BASE-X Half Duplex
This bit displays the status of 100BASE-X half duplex compatibility.
0: PHY not able to perform 100BASE-X half duplex
1: PHY able to perform 100BASE-X half duplex
12
10BASE-T Full Duplex
This bit displays the status of 10BASE-T full duplex compatibility.
0: PHY not able to perform 10BASE-T full duplex
1: PHY able to perform 10BASE-T full duplex
11
10BASE-T Half Duplex
This bit displays the status of 10BASE-T half duplex compatibility.
0: PHY not able to perform 10BASE-T half duplex
1: PHY able to perform 10BASE-T half duplex
10
100BASE-T2 Full Duplex
This bit displays the status of 100BASE-T2 full duplex compatibility.
0: PHY not able to perform 100BASE-T2 full duplex
1: PHY able to perform 100BASE-T2 full duplex
9
100BASE-T2 Half Duplex
This bit displays the status of 100BASE-T2 half duplex compatibility.
0: PHY not able to perform 100BASE-T2 half duplex
1: PHY able to perform 100BASE-T2 half duplex
8:6
5
0: Auto-Negotiation process not completed
1: Auto-Negotiation process completed
4
Remote Fault
This bit indicates if a remote fault condition has been detected.
0: No remote fault condition detected
1: Remote fault condition detected
Revision 2.0 (02-14-13)
290
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
3
DESCRIPTION
Auto-Negotiation Ability
This bit indicates the status of the PHY’s auto-negotiation.
TYPE
DEFAULT
RO
1b
RO/LL
0b
RO/LH
0b
RO
1b
0: PHY is unable to perform auto-negotiation
1: PHY is able to perform auto-negotiation
2
Link Status
This bit indicates the status of the link.
0: Link is down
1: Link is up
1
Jabber Detect
This bit indicates the status of the jabber condition.
0: No jabber condition detected
1: Jabber condition detected
0
Extended Capability
This bit indicates whether extended register capability is supported.
0: Basic register set capabilities only
1: Extended register set capabilities
Note 14.52 The PHY supports 100BASE-TX (half and full duplex) and 10BASE-T (half and full duplex)
only. All other modes will always return as 0 (unable to perform).
SMSC LAN9312
291
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.3
Port x PHY Identification MSB Register (PHY_ID_MSB_x)
Index (decimal):
2
Size:
16 bits
This read/write register contains the MSB of the Organizationally Unique Identifier (OUI) for the Port x
PHY. The LSB of the PHY OUI is contained in the Port x PHY Identification LSB Register
(PHY_ID_LSB_x).
BITS
15:0
DESCRIPTION
PHY ID
This field is assigned to the 3rd through 18th bits of the OUI, respectively
(OUI = 00800Fh).
Revision 2.0 (02-14-13)
292
DATASHEET
TYPE
DEFAULT
R/W
0007h
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.4
Port x PHY Identification LSB Register (PHY_ID_LSB_x)
Index (decimal):
3
Size:
16 bits
This read/write register contains the LSB of the Organizationally Unique Identifier (OUI) for the Port x
PHY. The MSB of the PHY OUI is contained in the Port x PHY Identification MSB Register
(PHY_ID_MSB_x).
BITS
TYPE
DEFAULT
PHY ID
This field is assigned to the 19th through 24th bits of the PHY OUI,
respectively. (OUI = 00800Fh).
R/W
110000b
9:4
Model Number
This field contains the 6-bit manufacturer’s model number of the PHY.
R/W
001101b
3:0
Revision Number
This field contain the 4-bit manufacturer’s revision number of the PHY.
R/W
0001b
15:10
DESCRIPTION
SMSC LAN9312
293
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.5
Port x PHY Auto-Negotiation Advertisement Register (PHY_AN_ADV_x)
Index (decimal):
4
Size:
16 bits
This read/write register contains the advertised ability of the Port x PHY and is used in the AutoNegotiation process with the link partner.
Note: This register is re-written by the EEPROM Loader following the release of reset or a RELOAD
command. Refer to Section 10.2.4, "EEPROM Loader," on page 149 for additional information.
BITS
15:14
13
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Remote Fault
This bit determines if remote fault indication will be advertised to the link
partner.
R/W
0b
R/W
0b
R/W
0b
Note 14.53
R/W
Note 14.53
Note 14.54
0: Remote fault indication not advertised
1: Remote fault indication advertised
12
RESERVED
Note:
11
This bit should be written as 0.
Asymmetric Pause
This bit determines the advertised asymmetric pause capability.
0: No Asymmetric PAUSE toward link partner advertised
1: Asymmetric PAUSE toward link partner advertised
10
Symmetric Pause
This bit determines the advertised symmetric pause capability.
0: No Symmetric PAUSE toward link partner advertised
1: Symmetric PAUSE toward link partner advertised
9
RESERVED
RO
-
8
100BASE-X Full Duplex
This bit determines the advertised 100BASE-X full duplex capability.
R/W
1b
R/W
1b
R/W
Note 14.55
Table 14.8
0: 100BASE-X full duplex ability not advertised
1: 100BASE-X full duplex ability advertised
7
100BASE-X Half Duplex
This bit determines the advertised 100BASE-X half duplex capability.
0: 100BASE-X half duplex ability not advertised
1: 100BASE-X half duplex ability advertised
6
10BASE-T Full Duplex
This bit determines the advertised 10BASE-T full duplex capability.
0: 10BASE-T full duplex ability not advertised
1: 10BASE-T full duplex ability advertised
Revision 2.0 (02-14-13)
294
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
5
DESCRIPTION
TYPE
DEFAULT
R/W
Note 14.56
Table 14.9
R/W
00001b
10BASE-T Half Duplex
This bit determines the advertised 10BASE-T half duplex capability.
0: 10BASE-T half duplex ability not advertised
1: 10BASE-T half duplex ability advertised
4:0
Selector Field
This field identifies the type of message being sent by Auto-Negotiation.
00001: IEEE 802.3
Note 14.53 The Pause and Asymmetric Pause bits are loaded into the PHY registers by the EEPROM
Loader.
Note 14.54 The default value of this bit is determined by the Manual Flow Control Enable Strap
(manual_FC_strap_x). When the Manual Flow Control Enable Strap is 0, this bit defaults
to 1 (symmetric pause advertised). When the Manual Flow Control Enable Strap is 1, this
bit defaults to 0 (symmetric pause not advertised). Configuration strap values are latched
upon the de-assertion of a chip-level reset as described in Section 4.2.4, "Configuration
Straps," on page 40. Refer to Section 4.2.4, "Configuration Straps," on page 40 for
configuration strap definitions.
Note 14.55 The default value of this bit is determined by the logical OR of the Auto-Negotiation strap
(autoneg_strap_x) with the logical AND of the negated speed select strap (speed_strap_x)
and (duplex_strap_x). Table 14.8 defines the default behavior of this bit. Configuration
strap values are latched upon the de-assertion of a chip-level reset as described in Section
4.2.4, "Configuration Straps," on page 40. Refer to Section 4.2.4, "Configuration Straps,"
on page 40 for configuration strap definitions.
Table 14.8 10BASE-T Full Duplex Advertisement Default Value
autoneg_strap_x
speed_strap_x
duplex_strap_x
Default 10BASE-T Full Duplex (Bit 6) Value
0
0
0
0
0
0
1
1
0
1
0
0
0
1
1
0
1
0
0
1
1
0
1
1
1
1
0
1
1
1
1
1
Note 14.56 The default value of this bit is determined by the logical OR of the Auto-Negotiation strap
(autoneg_strap_x) and the negated speed strap (speed_strap_x). Table 14.9 defines the
default behavior of this bit. Configuration strap values are latched upon the de-assertion
of a chip-level reset as described in Section 4.2.4, "Configuration Straps," on page 40.
Refer to Section 4.2.4, "Configuration Straps," on page 40 for configuration strap
definitions.
SMSC LAN9312
295
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.9 10BASE-T Half Duplex Advertisement Bit Default Value
autoneg_strap_x
speed_strap_x
Default 10BASE-T Half Duplex (Bit 5) Value
0
0
1
0
1
0
1
0
1
1
1
1
Revision 2.0 (02-14-13)
296
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.6
Port x PHY Auto-Negotiation Link Partner Base Page Ability Register
(PHY_AN_LP_BASE_ABILITY_x)
Index (decimal):
5
Size:
16 bits
This read-only register contains the advertised ability of the link partner’s PHY and is used in the AutoNegotiation process between the link partner and the Port x PHY.
BITS
15
DESCRIPTION
Next Page
This bit indicates the link partner PHY page capability.
TYPE
DEFAULT
RO
0b
RO
0b
RO
0b
0: Link partner PHY does not advertise next page capability
1: Link partner PHY advertises next page capability
14
Acknowledge
This bit indicates whether the link code word has been received from the
partner.
0: Link code word not yet received from partner
1: Link code word received from partner
13
Remote Fault
This bit indicates whether a remote fault has been detected.
0: No remote fault
1: Remote fault detected
12
RESERVED
RO
-
11
Asymmetric Pause
This bit indicates the link partner PHY asymmetric pause capability.
RO
0b
RO
0b
RO
0b
RO
0b
RO
0b
0: No Asymmetric PAUSE toward link partner
1: Asymmetric PAUSE toward link partner
10
Pause
This bit indicates the link partner PHY symmetric pause capability.
0: No Symmetric PAUSE toward link partner
1: Symmetric PAUSE toward link partner
9
100BASE-T4
This bit indicates the link partner PHY 100BASE-T4 capability.
0: 100BASE-T4 ability not supported
1: 100BASE-T4 ability supported
8
100BASE-X Full Duplex
This bit indicates the link partner PHY 100BASE-X full duplex capability.
0: 100BASE-X full duplex ability not supported
1: 100BASE-X full duplex ability supported
7
100BASE-X Half Duplex
This bit indicates the link partner PHY 100BASE-X half duplex capability.
0: 100BASE-X half duplex ability not supported
1: 100BASE-X half duplex ability supported
SMSC LAN9312
297
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
6
DESCRIPTION
10BASE-T Full Duplex
This bit indicates the link partner PHY 10BASE-T full duplex capability.
TYPE
DEFAULT
RO
0b
RO
0b
RO
00001b
Note 14.57
0: 10BASE-T full duplex ability not supported
1: 10BASE-T full duplex ability supported
5
10BASE-T Half Duplex
This bit indicates the link partner PHY 10BASE-T half duplex capability.
0: 10BASE-T half duplex ability not supported
1: 10BASE-T half duplex ability supported
4:0
Selector Field
This field identifies the type of message being sent by Auto-Negotiation.
00001: IEEE 802.3
Note 14.57 The Port 1 & 2 PHY’s support only IEEE 802.3.
Revision 2.0 (02-14-13)
298
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.7
Port x PHY Auto-Negotiation Expansion Register (PHY_AN_EXP_x)
Index (decimal):
6
Size:
16 bits
This read/write register is used in the Auto-Negotiation process between the link partner and the Port
x PHY.
BITS
15:5
4
DESCRIPTION
RESERVED
Parallel Detection Fault
This bit indicates whether a Parallel Detection Fault has been detected.
TYPE
DEFAULT
RO
-
RO/LH
0b
RO
0b
RO
0b
RO/LH
0b
RO
0b
0: A fault hasn’t been detected via the Parallel Detection function
1: A fault has been detected via the Parallel Detection function
3
Link Partner Next Page Able
This bit indicates whether the link partner has next page ability.
0: Link partner does not contain next page capability
1: Link partner contains next page capability
2
Local Device Next Page Able
This bit indicates whether the local device has next page ability.
0: Local device does not contain next page capability
1: Local device contains next page capability
1
Page Received
This bit indicates the reception of a new page.
0: A new page has not been received
1: A new page has been received
0
Link Partner Auto-Negotiation Able
This bit indicates the Auto-negotiation ability of the link partner.
0: Link partner is not Auto-Negotiation able
1: Link partner is Auto-Negotiation able
SMSC LAN9312
299
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.8
Port x PHY Mode Control/Status Register (PHY_MODE_CONTROL_STATUS_x)
Index (decimal):
17
Size:
16 bits
This read/write register is used to control and monitor various Port x PHY configuration options.
BITS
15:14
13
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Energy Detect Power-Down (EDPWRDOWN)
This bit controls the Energy Detect Power-Down mode.
R/W
0b
RESERVED
RO
-
Energy On (ENERGYON)
This bit indicates whether energy is detected on the line. It is cleared if no
valid energy is detected within 256ms. This bit is unaffected by a software
reset and is reset to 1 by a hardware reset.
RO
1b
R/W
0b
0: Energy Detect Power-Down is disabled
1: Energy Detect Power-Down is enabled
12:2
1
0: No valid energy detected on the line
1: Energy detected on the line
0
RESERVED
Revision 2.0 (02-14-13)
300
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.9
Port x PHY Special Modes Register (PHY_SPECIAL_MODES_x)
Index (decimal):
18
Size:
16 bits
This read/write register is used to control the special modes of the Port x PHY.
Note: This register is re-written by the EEPROM Loader following the release of reset or a RELOAD
command. Refer to Section 10.2.4, "EEPROM Loader," on page 149 for more information.
BITS
DESCRIPTION
15:8
RESERVED
7:5
PHY Mode (MODE[2:0])
This field controls the PHY mode of operation. Refer to Table 14.10 for a
definition of each mode.
4:0
PHY Address (PHYADD)
The PHY Address field determines the MMI address to which the PHY will
respond and is also used for initialization of the cipher (scrambler) key. Each
PHY must have a unique address. Refer to Section 7.1.1, "PHY
Addressing," on page 82 for additional information.
Note:
TYPE
DEFAULT
RO
-
R/W
NASR
Note 14.59
Note 14.58
R/W
NASR
Note 14.60
Note 14.58
No check is performed to ensure that this address is unique from
the other PHY addresses (Port 1 PHY, Port 2 PHY, and Virtual
PHY).
Note 14.58 Register bits designated as NASR are reset when the Port x PHY Reset is generated via
the Reset Control Register (RESET_CTL). The NASR designation is only applicable when
the Reset (PHY_RST) bit of the Port x PHY Basic Control Register
(PHY_BASIC_CONTROL_x) is set.
Note 14.59 The default value of this field is determined by a combination of the configuration straps
autoneg_strap_x, speed_strap_x, and duplex_strap_x. If the autoneg_strap_x is 1, then
the default MODE[2:0] value is 111b. Else, the default value of this field is determined by
the remaining straps. MODE[2]=0, MODE[1]=(speed_strap_1 for Port 1 PHY,
speed_strap_2 for Port 2 PHY), and MODE[0]=(duplex_strap_1 for Port 1 PHY,
duplex_strap_2 for Port 2 PHY). Configuration strap values are latched upon the deassertion of a chip-level reset as described in Section 4.2.4, "Configuration Straps," on
page 40. Refer to Section 4.2.4, "Configuration Straps," on page 40 for configuration strap
definitions.
Note 14.60 The default value of this field is determined by the phy_addr_sel_strap configuration strap.
Refer to Section 7.1.1, "PHY Addressing," on page 82 for additional information.
Table 14.10 MODE[2:0] Definitions
AFFECTED REGISTER BIT VALUES
MODE[2:0]
MODE DEFINITIONS
PHY_BASIC_CONTROL_x
PHY_AN_ADV_x
[13,12,10,8]
[8,7,6,5]
000
10BASE-T Half Duplex. Auto-negotiation disabled.
0000
N/A
001
10BASE-T Full Duplex. Auto-negotiation disabled.
0001
N/A
010
100BASE-TX Half Duplex. Auto-negotiation
disabled. CRS is active during Transmit & Receive.
1000
N/A
SMSC LAN9312
301
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.10 MODE[2:0] Definitions (continued)
AFFECTED REGISTER BIT VALUES
MODE[2:0]
MODE DEFINITIONS
PHY_BASIC_CONTROL_x
PHY_AN_ADV_x
[13,12,10,8]
[8,7,6,5]
011
100BASE-TX Full Duplex. Auto-negotiation
disabled. CRS is active during Receive.
1001
N/A
100
100BASE-TX Half Duplex is advertised. Autonegotiation enabled.
CRS is active during Transmit & Receive.
1100
0100
101
Repeater mode. Auto-negotiation enabled.
100BASE-TX Half Duplex is advertised.
CRS is active during Receive.
1100
0100
110
Power Down mode. In this mode the PHY wake-up
in Power-Down mode.
N/A
N/A
111
All capable. Auto-negotiation enabled.
X10X
1111
Revision 2.0 (02-14-13)
302
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.10
Port x PHY Special Control/Status Indication Register (PHY_SPECIAL_CONTROL_STAT_IND_x)
Index (decimal):
27
Size:
16 bits
This read/write register is used to control various options of the Port x PHY.
BITS
DESCRIPTION
TYPE
DEFAULT
15
Auto-MDIX Control (AMDIXCTRL)
This bit is responsible for determining the source of Auto-MDIX control for
Port x. When set, the Manual MDIX and Auto MDIX straps
(manual_mdix_strap_1/auto_mdix_strap_1 for Port 1 PHY,
manual_mdix_strap_2/auto_mdix_strap_2 for Port 2 PHY) are overridden,
and Auto-MDIX functions are controlled using bit 14 (AMDIXEN) and bit 13
(AMDIXSTATE) of this register. When cleared, Auto-MDIX functionality is
controlled by the Manual MDIX and Auto MDIX straps by default. Refer to
Section 4.2.4, "Configuration Straps," on page 40 for configuration strap
definitions.
R/W
NASR
0b
Note 14.61
0: Port x Auto-MDIX determined by strap inputs
1: Port x Auto-MDIX determined by bits 14 and 13
14
13
Auto-MDIX Enable (AMDIXEN)
When bit 15 (AMDIXCTRL) of this register is set, this bit is used in
conjunction with bit 13 (Auto-MDIX State) to control the Port x Auto-MDIX
functionality as shown in Table 14.11.
Auto-MDIX State (AMDIXSTATE)
When bit 15 (AMDIXCTRL) of this register is set, this bit is used in
conjunction with bit 14 (Auto-MDIX Enable) to control the Port x Auto-MDIX
functionality as shown in Table 14.11.
12
RESERVED
11
SQE Test Disable (SQEOFF)
This bit controls the disabling of the SQE test (Heartbeat). SQE test is
enabled by default.
R/W
NASR
0b
Note 14.61
R/W
NASR
0b
Note 14.61
RO
-
R/W
NASR
0b
Note 14.61
0: SQE test enabled
1: SQE test disabled
10
Receive PLL Lock Control (VCOOFF_LP)
This bit controls the locking of the receive PLL. Setting this bit to 1 forces
the receive PLL 10M to lock on the reference clock at all times. When in this
mode, 10M data packets cannot be received.
R/W
NASR
0b
Note 14.61
0: Receive PLL 10M can lock on reference or line as needed (normal
operation)
1: Receive PLL 10M locked onto reference clock at all times
9:5
4
RESERVED
RO
-
10Base-T Polarity State (XPOL)
This bit shows the polarity state of the 10Base-T.
RO
0b
RO
-
0: Normal Polarity
1: Reversed Polarity
3:0
RESERVED
Note 14.61 Register bits designated as NASR are reset when the Port x PHY Reset is generated via
the Reset Control Register (RESET_CTL). The NASR designation is only applicable when
the Reset (PHY_RST) bit of the Port x PHY Basic Control Register
(PHY_BASIC_CONTROL_x) is set.
SMSC LAN9312
303
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.11 Auto-MDIX Enable and Auto-MDIX State Bit Functionality
Auto-MDIX Enable
(Bit 14)
Auto-MDIX State
(Bit 13)
MODE
0
0
Manual mode, no crossover
0
1
Manual mode, crossover
1
0
Auto-MDIX mode
1
1
RESERVED (do not use this state)
Revision 2.0 (02-14-13)
304
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.11
Port x PHY Interrupt Source Flags Register (PHY_INTERRUPT_SOURCE_x)
Index (decimal):
29
Size:
16 bits
This read-only register is used to determine to source of various Port x PHY interrupts. All interrupt
source bits in this register are read-only and latch high upon detection of the corresponding interrupt
(if enabled). A read of this register clears the interrupts. These interrupts are enabled or masked via
the Port x PHY Interrupt Mask Register (PHY_INTERRUPT_MASK_x).
BITS
15:8
7
DESCRIPTION
RESERVED
INT7
This interrupt source bit indicates when the ENERGYON bit of the Port x
PHY Mode Control/Status Register (PHY_MODE_CONTROL_STATUS_x)
has been set.
TYPE
DEFAULT
RO
-
RO/LH
0b
RO/LH
0b
RO/LH
0b
RO/LH
0b
RO/LH
0b
RO/LH
0b
RO/LH
0b
RO
-
0: Not source of interrupt
1: ENERGYON generated
6
INT6
This interrupt source bit indicates Auto-Negotiation is complete.
0: Not source of interrupt
1: Auto-Negotiation complete
5
INT5
This interrupt source bit indicates a remote fault has been detected.
0: Not source of interrupt
1: Remote fault detected
4
INT4
This interrupt source bit indicates a Link Down (link status negated).
0: Not source of interrupt
1: Link Down (link status negated)
3
INT3
This interrupt source bit indicates an Auto-Negotiation LP acknowledge.
0: Not source of interrupt
1: Auto-Negotiation LP acknowledge
2
INT2
This interrupt source bit indicates a Parallel Detection fault.
0: Not source of interrupt
1: Parallel Detection fault
1
INT1
This interrupt source bit indicates an Auto-Negotiation page received.
0: Not source of interrupt
1: Auto-Negotiation page received
0
RESERVED
SMSC LAN9312
305
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.12
Port x PHY Interrupt Mask Register (PHY_INTERRUPT_MASK_x)
Index (decimal):
30
Size:
16 bits
This read/write register is used to enable or mask the various Port x PHY interrupts and is used in
conjunction with the Port x PHY Interrupt Source Flags Register (PHY_INTERRUPT_SOURCE_x).
BITS
15:8
7
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
INT7_MASK
This interrupt mask bit enables/masks the ENERGYON interrupt.
R/W
0b
R/W
0b
R/W
0b
R/W
0b
R/W
0b
R/W
0b
R/W
0b
RO
-
0: Interrupt source is masked
1: Interrupt source is enabled
6
INT6_MASK
This interrupt mask bit enables/masks the Auto-Negotiation interrupt.
0: Interrupt source is masked
1: Interrupt source is enabled
5
INT5_MASK
This interrupt mask bit enables/masks the remote fault interrupt.
0: Interrupt source is masked
1: Interrupt source is enabled
4
INT4_MASK
This interrupt mask bit enables/masks the Link Down (link status negated)
interrupt.
0: Interrupt source is masked
1: Interrupt source is enabled
3
INT3_MASK
This interrupt mask bit enables/masks the Auto-Negotiation LP acknowledge
interrupt.
0: Interrupt source is masked
1: Interrupt source is enabled
2
INT2_MASK
This interrupt mask bit enables/masks the Parallel Detection fault interrupt.
0: Interrupt source is masked
1: Interrupt source is enabled
1
INT1_MASK
This interrupt mask bit enables/masks the Auto-Negotiation page received
interrupt.
0: Interrupt source is masked
1: Interrupt source is enabled
0
RESERVED
Revision 2.0 (02-14-13)
306
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.4.2.13
Port x PHY Special Control/Status Register (PHY_SPECIAL_CONTROL_STATUS_x)
Index (decimal):
31
Size:
16 bits
This read/write register is used to control and monitor various options of the Port x PHY.
BITS
15:13
12
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Autodone
This bit indicates the status of the Auto-Negotiation on the Port x PHY.
RO
0b
0: Auto-Negotiation is not completed, is disabled, or is not active
1: Auto-Negotiation is completed
11:5
RESERVED - Write as 0000010b, ignore on read
R/W
0000010b
4:2
Speed Indication
This field indicates the current Port x PHY speed configuration.
RO
000b
R/W
0b
STATE
000
1:0
DESCRIPTION
RESERVED
001
10BASE-T Half-duplex
010
100BASE-TX Half-duplex
011
RESERVED
100
RESERVED
101
10BASE-T Full-duplex
110
100BASE-TX Full-duplex
111
RESERVED
RESERVED
SMSC LAN9312
307
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5
Switch Fabric Control and Status Registers
This section details the various LAN9312 switch control and status registers that reside within the
switch fabric. The switch control and status registers allow configuration of each individual switch port,
the switch engine, and buffer manager. Switch fabric related interrupts and resets are also controlled
and monitored via the switch CSRs.
The switch CSRs are not memory mapped. All switch CSRs are accessed indirectly via the Switch
Fabric CSR Interface Command Register (SWITCH_CSR_CMD), Switch Fabric CSR Interface Data
Register (SWITCH_CSR_DATA), and Switch Fabric CSR Interface Direct Data Register
(SWITCH_CSR_DIRECT_DATA) in the system CSR memory mapped address space. All accesses to
the switch CSRs must be performed through these registers. Refer to Section 14.2.6, "Switch Fabric"
for additional information.
Note: The flow control settings of the switch ports are configured via the Switch Fabric registers: Port
1 Manual Flow Control Register (MANUAL_FC_1), Port 2 Manual Flow Control Register
(MANUAL_FC_2), and Port 0(Host MAC) Manual Flow Control Register (MANUAL_FC_MII)
located in the system CSR address space.
Table 14.12 lists the Switch CSRs and their corresponding addresses in order. The switch fabric
registers can be categorized into the following sub-sections:

Section 14.5.1, "General Switch CSRs," on page 319

Section 14.5.2, "Switch Port 0, Port 1, and Port 2 CSRs," on page 323

Section 14.5.3, "Switch Engine CSRs," on page 367

Section 14.5.4, "Buffer Manager CSRs," on page 412
Table 14.12 Indirectly Accessible Switch Control and Status Registers
REGISTER #
SYMBOL
REGISTER NAME
General Switch CSRs
0000h
SW_DEV_ID
Switch Device ID Register, Section 14.5.1.1
0001h
SW_RESET
Switch Reset Register, Section 14.5.1.2
0002h-0003h
RESERVED
Reserved for Future Use
0004h
SW_IMR
Switch Global Interrupt Mask Register, Section 14.5.1.3
0005h
SW_IPR
Switch Global Interrupt Pending Register, Section 14.5.1.4
0006h-03FFh
RESERVED
Reserved for Future Use
Switch Port 0 CSRs
0400h
MAC_VER_ID_MII
Port 0 MAC Version ID Register, Section 14.5.2.1
0401h
MAC_RX_CFG_MII
Port 0 MAC Receive Configuration Register, Section 14.5.2.2
0402h-040Fh
RESERVED
0410h
MAC_RX_UNDSZE_CNT_MII
0411h
MAC_RX_64_CNT_MII
0412h
MAC_RX_65_TO_127_CNT_MII
Port 0 MAC Receive 65 to 127 Byte Count Register,
Section 14.5.2.5
0413h
MAC_RX_128_TO_255_CNT_MII
Port 0 MAC Receive 128 to 255 Byte Count Register,
Section 14.5.2.6
Revision 2.0 (02-14-13)
Reserved for Future Use
Port 0 MAC Receive Undersize Count Register,
Section 14.5.2.3
Port 0 MAC Receive 64 Byte Count Register, Section 14.5.2.4
308
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.12 Indirectly Accessible Switch Control and Status Registers (continued)
REGISTER #
SYMBOL
0414h
MAC_RX_256_TO_511_CNT_MII
Port 0 MAC Receive 256 to 511 Byte Count Register,
Section 14.5.2.7
0415h
MAC_RX_512_TO_1023_CNT_MII
Port 0 MAC Receive 512 to 1023 Byte Count Register,
Section 14.5.2.8
0416h
MAC_RX_1024_TO_MAX_CNT_MII
Port 0 MAC Receive 1024 to Max Byte Count Register,
Section 14.5.2.9
0417h
MAC_RX_OVRSZE_CNT_MII
Port 0 MAC Receive Oversize Count Register,
Section 14.5.2.10
0418h
MAC_RX_PKTOK_CNT_MII
Port 0 MAC Receive OK Count Register, Section 14.5.2.11
0419h
MAC_RX_CRCERR_CNT_MII
Port 0 MAC Receive CRC Error Count Register,
Section 14.5.2.12
041Ah
MAC_RX_MULCST_CNT_MII
Port 0 MAC Receive Multicast Count Register,
Section 14.5.2.13
041Bh
MAC_RX_BRDCST_CNT_MII
Port 0 MAC Receive Broadcast Count Register,
Section 14.5.2.14
041Ch
MAC_RX_PAUSE_CNT_MII
Port 0 MAC Receive Pause Frame Count Register,
Section 14.5.2.15
041Dh
MAC_RX_FRAG_CNT_MII
Port 0 MAC Receive Fragment Error Count Register,
Section 14.5.2.16
041Eh
MAC_RX_JABB_CNT_MII
Port 0 MAC Receive Jabber Error Count Register,
Section 14.5.2.17
041Fh
MAC_RX_ALIGN_CNT_MII
Port 0 MAC Receive Alignment Error Count Register,
Section 14.5.2.18
0420h
MAC_RX_PKTLEN_CNT_MII
0421h
MAC_RX_GOODPKTLEN_CNT_MII
Port 0 MAC Receive Good Packet Length Count Register,
Section 14.5.2.20
0422h
MAC_RX_SYMBL_CNT_MII
Port 0 MAC Receive Symbol Error Count Register,
Section 14.5.2.21
0423h
MAC_RX_CTLFRM_CNT_MII
0424h-043Fh
RESERVED
0440h
MAC_TX_CFG_MII
0441h
MAC_TX_FC_SETTINGS_MII
0442h-0450h
RESERVED
0451h
MAC_TX_DEFER_CNT_MII
Port 0 MAC Transmit Deferred Count Register,
Section 14.5.2.25
0452h
MAC_TX_PAUSE_CNT_MII
Port 0 MAC Transmit Pause Count Register, Section 14.5.2.26
0453h
MAC_TX_PKTOK_CNT_MII
Port 0 MAC Transmit OK Count Register, Section 14.5.2.27
0454h
MAC_TX_64_CNT_MII
SMSC LAN9312
REGISTER NAME
Port 0 MAC Receive Packet Length Count Register,
Section 14.5.2.19
Port 0 MAC Receive Control Frame Count Register,
Section 14.5.2.22
Reserved for Future Use
Port 0 MAC Transmit Configuration Register, Section 14.5.2.23
Port 0 MAC Transmit Flow Control Settings Register,
Section 14.5.2.24
Reserved for Future Use
Port 0 MAC Transmit 64 Byte Count Register, Section 14.5.2.28
309
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.12 Indirectly Accessible Switch Control and Status Registers (continued)
REGISTER #
SYMBOL
REGISTER NAME
0455h
MAC_TX_65_TO_127_CNT_MII
Port 0 MAC Transmit 65 to 127 Byte Count Register,
Section 14.5.2.29
0456h
MAC_TX_128_TO_255_CNT_MII
Port 0 MAC Transmit 128 to 255 Byte Count Register,
Section 14.5.2.30
0457h
MAC_TX_256_TO_511_CNT_MII
Port 0 MAC Transmit 256 to 511 Byte Count Register,
Section 14.5.2.31
0458h
MAC_TX_512_TO_1023_CNT_MII
Port 0 MAC Transmit 512 to 1023 Byte Count Register,
Section 14.5.2.32
0459h
MAC_TX_1024_TO_MAX_CNT_MII
Port 0 MAC Transmit 1024 to Max Byte Count Register,
Section 14.5.2.33
045Ah
MAC_TX_UNDSZE_CNT_MII
045Bh
RESERVED
045Ch
MAC_TX_PKTLEN_CNT_MII
Port 0 MAC Transmit Packet Length Count Register,
Section 14.5.2.35
045Dh
MAC_TX_BRDCST_CNT_MII
Port 0 MAC Transmit Broadcast Count Register,
Section 14.5.2.36
045Eh
MAC_TX_MULCST_CNT_MII
Port 0 MAC Transmit Multicast Count Register,
Section 14.5.2.37
045Fh
MAC_TX_LATECOL_MII
0460h
MAC_TX_EXCOL_CNT_MII
Port 0 MAC Transmit Excessive Collision Count Register,
Section 14.5.2.39
0461h
MAC_TX_SNGLECOL_CNT_MII
Port 0 MAC Transmit Single Collision Count Register,
Section 14.5.2.40
0462h
MAC_TX_MULTICOL_CNT_MII
Port 0 MAC Transmit Multiple Collision Count Register,
Section 14.5.2.41
0463h
MAC_TX_TOTALCOL_CNT_MII
Port 0 MAC Transmit Total Collision Count Register,
Section 14.5.2.42
0464-047Fh
RESERVED
0480h
MAC_IMR_MII
Port 0 MAC Interrupt Mask Register, Section 14.5.2.43
0481h
MAC_IPR_MII
Port 0 MAC Interrupt Pending Register, Section 14.5.2.44
0482h-07FFh
RESERVED
Port 0 MAC Transmit Undersize Count Register,
Section 14.5.2.34
Reserved for Future Use
Port 0 MAC Transmit Late Collision Count Register,
Section 14.5.2.38
Reserved for Future Use
Reserved for Future Use
Switch Port 1 CSRs
0800h
MAC_VER_ID_1
Port 1 MAC Version ID Register, Section 14.5.2.1
0801h
MAC_RX_CFG_1
Port 1 MAC Receive Configuration Register, Section 14.5.2.2
0802h-080Fh
RESERVED
0810h
MAC_RX_UNDSZE_CNT_1
0811h
MAC_RX_64_CNT_1
Revision 2.0 (02-14-13)
Reserved for Future Use
Port 1 MAC Receive Undersize Count Register,
Section 14.5.2.3
Port 1 MAC Receive 64 Byte Count Register, Section 14.5.2.4
310
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.12 Indirectly Accessible Switch Control and Status Registers (continued)
REGISTER #
SYMBOL
0812h
MAC_RX_65_TO_127_CNT_1
Port 1 MAC Receive 65 to 127 Byte Count Register,
Section 14.5.2.5
0813h
MAC_RX_128_TO_255_CNT_1
Port 1 MAC Receive 128 to 255 Byte Count Register,
Section 14.5.2.6
0814h
MAC_RX_256_TO_511_CNT_1
Port 1 MAC Receive 256 to 511 Byte Count Register,
Section 14.5.2.7
0815h
MAC_RX_512_TO_1023_CNT_1
Port 1 MAC Receive 512 to 1023 Byte Count Register,
Section 14.5.2.8
0816h
MAC_RX_1024_TO_MAX_CNT_1
Port 1 MAC Receive 1024 to Max Byte Count Register,
Section 14.5.2.9
0817h
MAC_RX_OVRSZE_CNT_1
0818h
MAC_RX_PKTOK_CNT_1
0819h
MAC_RX_CRCERR_CNT_1
Port 1 MAC Receive CRC Error Count Register,
Section 14.5.2.12
081Ah
MAC_RX_MULCST_CNT_1
Port 1 MAC Receive Multicast Count Register,
Section 14.5.2.13
081Bh
MAC_RX_BRDCST_CNT_1
Port 1 MAC Receive Broadcast Count Register,
Section 14.5.2.14
081Ch
MAC_RX_PAUSE_CNT_1
Port 1 MAC Receive Pause Frame Count Register,
Section 14.5.2.15
081Dh
MAC_RX_FRAG_CNT_1
Port 1 MAC Receive Fragment Error Count Register,
Section 14.5.2.16
081Eh
MAC_RX_JABB_CNT_1
Port 1 MAC Receive Jabber Error Count Register,
Section 14.5.2.17
081Fh
MAC_RX_ALIGN_CNT_1
Port 1 MAC Receive Alignment Error Count Register,
Section 14.5.2.18
0820h
MAC_RX_PKTLEN_CNT_1
Port 1 MAC Receive Packet Length Count Register,
Section 14.5.2.19
0821h
MAC_RX_GOODPKTLEN_CNT_1
Port 1 MAC Receive Good Packet Length Count Register,
Section 14.5.2.20
0822h
MAC_RX_SYMBL_CNT_1
Port 1 MAC Receive Symbol Error Count Register,
Section 14.5.2.21
0823h
MAC_RX_CTLFRM_CNT_1
Port 1 MAC Receive Control Frame Count Register,
Section 14.5.2.22
0824h-083Fh
RESERVED
0840h
MAC_TX_CFG_1
0841h
MAC_TX_FC_SETTINGS_1
0842h-0850h
RESERVED
0851h
MAC_TX_DEFER_CNT_1
SMSC LAN9312
REGISTER NAME
Port 1 MAC Receive Oversize Count Register,
Section 14.5.2.10
Port 1 MAC Receive OK Count Register, Section 14.5.2.11
Reserved for Future Use
Port 1 MAC Transmit Configuration Register, Section 14.5.2.23
Port 1 MAC Transmit Flow Control Settings Register,
Section 14.5.2.24
Reserved for Future Use
Port 1 MAC Transmit Deferred Count Register,
Section 14.5.2.25
311
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.12 Indirectly Accessible Switch Control and Status Registers (continued)
REGISTER #
SYMBOL
REGISTER NAME
0852h
MAC_TX_PAUSE_CNT_1
Port 1 MAC Transmit Pause Count Register, Section 14.5.2.26
0853h
MAC_TX_PKTOK_CNT_1
Port 1 MAC Transmit OK Count Register, Section 14.5.2.27
0854h
MAC_RX_64_CNT_1
0855h
MAC_TX_65_TO_127_CNT_1
Port 1 MAC Transmit 65 to 127 Byte Count Register,
Section 14.5.2.29
0856h
MAC_TX_128_TO_255_CNT_1
Port 1 MAC Transmit 128 to 255 Byte Count Register,
Section 14.5.2.30
0857h
MAC_TX_256_TO_511_CNT_1
Port 1 MAC Transmit 256 to 511 Byte Count Register,
Section 14.5.2.31
0858h
MAC_TX_512_TO_1023_CNT_1
Port 1 MAC Transmit 512 to 1023 Byte Count Register,
Section 14.5.2.32
0859h
MAC_TX_1024_TO_MAX_CNT_1
Port 1 MAC Transmit 1024 to Max Byte Count Register,
Section 14.5.2.33
085Ah
MAC_TX_UNDSZE_CNT_1
Port 1 MAC Transmit Undersize Count Register,
Section 14.5.2.34
085Bh
RESERVED
085Ch
MAC_TX_PKTLEN_CNT_1
Port 1 MAC Transmit Packet Length Count Register,
Section 14.5.2.35
085Dh
MAC_TX_BRDCST_CNT_1
Port 1 MAC Transmit Broadcast Count Register,
Section 14.5.2.36
085Eh
MAC_TX_MULCST_CNT_1
Port 1 MAC Transmit Multicast Count Register,
Section 14.5.2.37
085Fh
MAC_TX_LATECOL_1
0860h
MAC_TX_EXCOL_CNT_1
0861h
MAC_TX_SNGLECOL_CNT_1
Port 1 MAC Transmit Single Collision Count Register,
Section 14.5.2.40
0862h
MAC_TX_MULTICOL_CNT_1
Port 1 MAC Transmit Multiple Collision Count Register,
Section 14.5.2.41
0863h
MAC_TX_TOTALCOL_CNT_1
Port 1 MAC Transmit Total Collision Count Register,
Section 14.5.2.42
0864-087Fh
RESERVED
Reserved for Future Use
0880h
MAC_IMR_1
Port 1 MAC Interrupt Mask Register, Section 14.5.2.43
0881h
MAC_IPR_1
Port 1 MAC Interrupt Pending Register, Section 14.5.2.44
0882h-0BFFh
RESERVED
Reserved for Future Use
Port 1 MAC Transmit 64 Byte Count Register, Section 14.5.2.28
Reserved for Future Use
Port 1 MAC Transmit Late Collision Count Register,
Section 14.5.2.38
Port 1 MAC Transmit Excessive Collision Count Register,
Section 14.5.2.39
Switch Port 2 CSRs
0C00h
MAC_VER_ID_2
Port 2 MAC Version ID Register, Section 14.5.2.1
0C01h
MAC_RX_CFG_2
Port 2 MAC Receive Configuration Register, Section 14.5.2.2
Revision 2.0 (02-14-13)
312
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.12 Indirectly Accessible Switch Control and Status Registers (continued)
REGISTER #
SYMBOL
0C02h-0C0Fh
RESERVED
0C10h
MAC_RX_UNDSZE_CNT_2
0C11h
MAC_RX_64_CNT_2
0C12h
MAC_RX_65_TO_127_CNT_2
Port 2 MAC Receive 65 to 127 Byte Count Register,
Section 14.5.2.5
0C13h
MAC_RX_128_TO_255_CNT_2
Port 2 MAC Receive 128 to 255 Byte Count Register,
Section 14.5.2.6
0C14h
MAC_RX_256_TO_511_CNT_2
Port 2 MAC Receive 256 to 511 Byte Count Register,
Section 14.5.2.7
0C15h
MAC_RX_512_TO_1023_CNT_2
Port 2 MAC Receive 512 to 1023 Byte Count Register,
Section 14.5.2.8
0C16h
MAC_RX_1024_TO_MAX_CNT_2
Port 2 MAC Receive 1024 to Max Byte Count Register,
Section 14.5.2.9
0C17h
MAC_RX_OVRSZE_CNT_2
0C18h
MAC_RX_PKTOK_CNT_2
0C19h
MAC_RX_CRCERR_CNT_2
Port 2 MAC Receive CRC Error Count Register,
Section 14.5.2.12
0C1Ah
MAC_RX_MULCST_CNT_2
Port 2 MAC Receive Multicast Count Register,
Section 14.5.2.13
0C1Bh
MAC_RX_BRDCST_CNT_2
Port 2 MAC Receive Broadcast Count Register,
Section 14.5.2.14
0C1Ch
MAC_RX_PAUSE_CNT_2
Port 2 MAC Receive Pause Frame Count Register,
Section 14.5.2.15
0C1Dh
MAC_RX_FRAG_CNT_2
Port 2 MAC Receive Fragment Error Count Register,
Section 14.5.2.16
0C1Eh
MAC_RX_JABB_CNT_2
Port 2 MAC Receive Jabber Error Count Register,
Section 14.5.2.17
0C1Fh
MAC_RX_ALIGN_CNT_2
Port 2 MAC Receive Alignment Error Count Register,
Section 14.5.2.18
0C20h
MAC_RX_PKTLEN_CNT_2
Port 2 MAC Receive Packet Length Count Register,
Section 14.5.2.19
0C21h
MAC_RX_GOODPKTLEN_CNT_2
Port 2 MAC Receive Good Packet Length Count Register,
Section 14.5.2.20
0C22h
MAC_RX_SYMBL_CNT_2
Port 2 MAC Receive Symbol Error Count Register,
Section 14.5.2.21
0C23h
MAC_RX_CTLFRM_CNT_2
Port 2 MAC Receive Control Frame Count Register,
Section 14.5.2.22
0C24h-0C3Fh
RESERVED
0C40h
MAC_TX_CFG_2
SMSC LAN9312
REGISTER NAME
Reserved for Future Use
Port 2 MAC Receive Undersize Count Register,
Section 14.5.2.3
Port 2 MAC Receive 64 Byte Count Register, Section 14.5.2.4
Port 2 MAC Receive Oversize Count Register,
Section 14.5.2.10
Port 2 MAC Receive OK Count Register, Section 14.5.2.11
Reserved for Future Use
Port 2 MAC Transmit Configuration Register, Section 14.5.2.23
313
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.12 Indirectly Accessible Switch Control and Status Registers (continued)
REGISTER #
SYMBOL
0C41h
MAC_TX_FC_SETTINGS_2
0C42h-0C50h
RESERVED
0C51h
MAC_TX_DEFER_CNT_2
Port 2 MAC Transmit Deferred Count Register,
Section 14.5.2.25
0C52h
MAC_TX_PAUSE_CNT_2
Port 2 MAC Transmit Pause Count Register, Section 14.5.2.26
0C53h
MAC_TX_PKTOK_CNT_2
Port 2 MAC Transmit OK Count Register, Section 14.5.2.27
0C54h
MAC_RX_64_CNT_2
0C55h
MAC_TX_65_TO_127_CNT_2
Port 2 MAC Transmit 65 to 127 Byte Count Register,
Section 14.5.2.29
0C56h
MAC_TX_128_TO_255_CNT_2
Port 2 MAC Transmit 128 to 255 Byte Count Register,
Section 14.5.2.30
0C57h
MAC_TX_256_TO_511_CNT_2
Port 2 MAC Transmit 256 to 511 Byte Count Register,
Section 14.5.2.31
0C58h
MAC_TX_512_TO_1023_CNT_2
Port 2 MAC Transmit 512 to 1023 Byte Count Register,
Section 14.5.2.32
0C59h
MAC_TX_1024_TO_MAX_CNT_2
Port 2 MAC Transmit 1024 to Max Byte Count Register,
Section 14.5.2.33
0C5Ah
MAC_TX_UNDSZE_CNT_2
Port 2 MAC Transmit Undersize Count Register,
Section 14.5.2.34
0C5Bh
RESERVED
0C5Ch
MAC_TX_PKTLEN_CNT_2
Port 2 MAC Transmit Packet Length Count Register,
Section 14.5.2.35
0C5Dh
MAC_TX_BRDCST_CNT_2
Port 2 MAC Transmit Broadcast Count Register,
Section 14.5.2.36
0C5Eh
MAC_TX_MULCST_CNT_2
Port 2 MAC Transmit Multicast Count Register,
Section 14.5.2.37
0C5Fh
MAC_TX_LATECOL_2
0C60h
MAC_TX_EXCOL_CNT_2
0C61h
MAC_TX_SNGLECOL_CNT_2
Port 2 MAC Transmit Single Collision Count Register,
Section 14.5.2.40
0C62h
MAC_TX_MULTICOL_CNT_2
Port 2 MAC Transmit Multiple Collision Count Register,
Section 14.5.2.41
0C63h
MAC_TX_TOTALCOL_CNT_2
Port 2 MAC Transmit Total Collision Count Register,
Section 14.5.2.42
0C64-0C7Fh
RESERVED
Reserved for Future Use
0C80h
MAC_IMR_2
Port 2 MAC Interrupt Mask Register, Section 14.5.2.43
0C81h
MAC_IPR_2
Port 2 MAC Interrupt Pending Register, Section 14.5.2.44
Revision 2.0 (02-14-13)
REGISTER NAME
Port 2 MAC Transmit Flow Control Settings Register,
Section 14.5.2.24
Reserved for Future Use
Port 2 MAC Transmit 64 Byte Count Register, Section 14.5.2.28
Reserved for Future Use
Port 2 MAC Transmit Late Collision Count Register,
Section 14.5.2.38
Port 2 MAC Transmit Excessive Collision Count Register,
Section 14.5.2.39
314
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.12 Indirectly Accessible Switch Control and Status Registers (continued)
REGISTER #
SYMBOL
0C82h-17FFh
RESERVED
REGISTER NAME
Reserved for Future Use
Switch Engine CSRs
1800h
SWE_ALR_CMD
1801h
SWE_ALR_WR_DAT_0
Switch Engine ALR Write Data 0 Register, Section 14.5.3.2
1802h
SWE_ALR_WR_DAT_1
Switch Engine ALR Write Data 1 Register, Section 14.5.3.3
1803h-1804h
RESERVED
1805h
SWE_ALR_RD_DAT_0
Switch Engine ALR Read Data 0 Register, Section 14.5.3.4
1806h
SWE_ALR_RD_DAT_1
Switch Engine ALR Read Data 1 Register, Section 14.5.3.5
1807h
RESERVED
1808h
SWE_ALR_CMD_STS
1809h
SWE_ALR_CFG
180Ah
RESERVED
180Bh
SWE_VLAN_CMD
Switch Engine VLAN Command Register, Section 14.5.3.8
180Ch
SWE_VLAN_WR_DATA
Switch Engine VLAN Write Data Register, Section 14.5.3.9
180Dh
RESERVED
180Eh
SWE_VLAN_RD_DATA
180Fh
RESERVED
1810h
SWE_VLAN_CMD_STS
1811h
SWE_DIFFSERV_TBL_CMD
Switch Engine DIFSERV Table Command Register,
Section 14.5.3.12
1812h
SWE_DIFFSERV_TBL_WR_DATA
Switch Engine DIFFSERV Table Write Data Register,
Section 14.5.3.13
1813h
SWE_DIFFSERV_TBL_RD_DATA
Switch Engine DIFFSERV Table Read Data Register,
Section 14.5.3.14
1814h
SWE_DIFFSERV_TBL_CMD_STS
Switch Engine DIFFSERV Table Command Status Register,
Section 14.5.3.15
1815h-183Fh
RESERVED
1840h
SWE_GLB_INGRESS_CFG
Switch Engine Global Ingress Configuration Register,
Section 14.5.3.16
1841h
SWE_PORT_INGRESS_CFG
Switch Engine Port Ingress Configuration Register,
Section 14.5.3.17
1842h
SWE_ADMT_ONLY_VLAN
Switch Engine Admit Only VLAN Register, Section 14.5.3.18
1843h
SWE_PORT_STATE
1844h
RESERVED
1845h
SWE_PRI_TO_QUE
SMSC LAN9312
Switch Engine ALR Command Register, Section 14.5.3.1
Reserved for Future Use
Reserved for Future Use
Switch Engine ALR Command Status Register, Section 14.5.3.6
Switch Engine ALR Configuration Register, Section 14.5.3.7
Reserved for Future Use
Reserved for Future Use
Switch Engine VLAN Read Data Register, Section 14.5.3.10
Reserved for Future Use
Switch Engine VLAN Command Status Register,
Section 14.5.3.11
Reserved for Future Use
Switch Engine Port State Register, Section 14.5.3.19
Reserved for Future Use
Switch Engine Priority to Queue Register, Section 14.5.3.20
315
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.12 Indirectly Accessible Switch Control and Status Registers (continued)
REGISTER #
SYMBOL
REGISTER NAME
1846h
SWE_PORT_MIRROR
1847h
SWE_INGRESS_PORT_TYP
1848h
SWE_BCST_THROT
Switch Engine Broadcast Throttling Register, Section 14.5.3.23
1849h
SWE_ADMT_N_MEMBER
Switch Engine Admit Non Member Register, Section 14.5.3.24
184Ah
SWE_INGRESS_RATE_CFG
Switch Engine Ingress Rate Configuration Register,
Section 14.5.3.25
184Bh
SWE_INGRESS_RATE_CMD
Switch Engine Ingress Rate Command Register,
Section 14.5.3.26
184Ch
SWE_INGRESS_RATE_CMD_STS
Switch Engine Ingress Rate Command Status Register,
Section 14.5.3.27
184Dh
SWE_INGRESS_RATE_WR_DATA
Switch Engine Ingress Rate Write Data Register,
Section 14.5.3.28
184Eh
SWE_INGRESS_RATE_RD_DATA
Switch Engine Ingress Rate Read Data Register,
Section 14.5.3.29
184Fh
RESERVED
1850h
SWE_FILTERED_CNT_MII
Switch Engine Port 0 Ingress Filtered Count Register,
Section 14.5.3.30
1851h
SWE_FILTERED_CNT_1
Switch Engine Port 1 Ingress Filtered Count Register,
Section 14.5.3.31
1852h
SWE_FILTERED_CNT_2
Switch Engine Port 2 Ingress Filtered Count Register,
Section 14.5.3.32
1853h-1854h
RESERVED
1855h
SWE_INGRESS_REGEN_TBL_MII
Switch Engine Port 0 Ingress VLAN Priority Regeneration
Register, Section 14.5.3.33
1856h
SWE_INGRESS_REGEN_TBL_1
Switch Engine Port 1 Ingress VLAN Priority Regeneration
Register, Section 14.5.3.34
1857h
SWE_INGRESS_REGEN_TBL_2
Switch Engine Port 2 Ingress VLAN Priority Regeneration
Register, Section 14.5.3.35
1858h
SWE_LRN_DISCRD_CNT_MII
Switch Engine Port 0 Learn Discard Count Register,
Section 14.5.3.36
1859h
SWE_LRN_DISCRD_CNT_1
Switch Engine Port 1 Learn Discard Count Register,
Section 14.5.3.37
185Ah
SWE_LRN_DISCRD_CNT_2
Switch Engine Port 2 Learn Discard Count Register,
Section 14.5.3.38
185Bh-187Fh
RESERVED
1880h
SWE_IMR
Switch Engine Interrupt Mask Register, Section 14.5.3.39
1881h
SWE_IPR
Switch Engine Interrupt Pending Register, Section 14.5.3.40
1882h-1BFFh
RESERVED
Switch Engine Port Mirroring Register, Section 14.5.3.21
Switch Engine Ingress Port Type Register, Section 14.5.3.22
Reserved for Future Use
Reserved for Future Use
Reserved for Future Use
Reserved for Future Use
Buffer Manager (BM) CSRs
Revision 2.0 (02-14-13)
316
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.12 Indirectly Accessible Switch Control and Status Registers (continued)
REGISTER #
SYMBOL
1C00h
BM_CFG
1C01h
BM_DROP_LVL
1C02h
BM_FC_PAUSE_LVL
1C03h
BM_FC_RESUME_LVL
1C04h
BM_BCST_LVL
1C05h
BM_DRP_CNT_SRC_MII
Buffer Manager Port 0 Drop Count Register, Section 14.5.4.6
1C06h
BM_DRP_CNT_SRC_1
Buffer Manager Port 1 Drop Count Register, Section 14.5.4.7
1C07h
BM_DRP_CNT_SRC_2
Buffer Manager Port 2 Drop Count Register, Section 14.5.4.8
1C08h
BM_RST_STS
1C09h
BM_RNDM_DSCRD_TBL_CMD
Buffer Manager Random Discard Table Command Register,
Section 14.5.4.10
1C0Ah
BM_RNDM_DSCRD_TBL_WDATA
Buffer Manager Random Discard Table Write Data Register,
Section 14.5.4.11
1C0Bh
BM_RNDM_DSCRD_TBL_RDATA
Buffer Manager Random Discard Table Read Data Register,
Section 14.5.4.12
1C0Ch
BM_EGRSS_PORT_TYPE
Buffer Manager Egress Port Type Register, Section 14.5.4.13
1C0Dh
BM_EGRSS_RATE_00_01
Buffer Manager Port 0 Egress Rate Priority Queue 0/1 Register,
Section 14.5.4.14
1C0Eh
BM_EGRSS_RATE_02_03
Buffer Manager Port 0 Egress Rate Priority Queue 2/3 Register,
Section 14.5.4.15
1C0Fh
BM_EGRSS_RATE_10_11
Buffer Manager Port 1 Egress Rate Priority Queue 0/1 Register,
Section 14.5.4.16
1C10h
BM_EGRSS_RATE_12_13
Buffer Manager Port 1 Egress Rate Priority Queue 2/3 Register,
Section 14.5.4.17
1C11h
BM_EGRSS_RATE_20_21
Buffer Manager Port 2 Egress Rate Priority Queue 0/1 Register,
Section 14.5.4.18
1C12h
BM_EGRSS_RATE_22_23
Buffer Manager Port 2 Egress Rate Priority Queue 2/3 Register,
Section 14.5.4.19
1C13h
BM_VLAN_MII
Buffer Manager Port 0 Default VLAN ID and Priority Register,
Section 14.5.4.20
1C14h
BM_VLAN_1
Buffer Manager Port 1 Default VLAN ID and Priority Register,
Section 14.5.4.21
1C15h
BM_VLAN_2
Buffer Manager Port 2 Default VLAN ID and Priority Register,
Section 14.5.4.22
1C16h
BM_RATE_DRP_CNT_SRC_MII
Buffer Manager Port 0 Ingress Rate Drop Count Register,
Section 14.5.4.23
1C17h
BM_RATE_DRP_CNT_SRC_1
Buffer Manager Port 1 Ingress Rate Drop Count Register,
Section 14.5.4.24
SMSC LAN9312
REGISTER NAME
Buffer Manager Configuration Register, Section 14.5.4.1
Buffer Manager Drop Level Register, Section 14.5.4.2
Buffer Manager Flow Control Pause Level Register,
Section 14.5.4.3
Buffer Manager Flow Control Resume Level Register,
Section 14.5.4.4
Buffer Manager Broadcast Buffer Level Register,
Section 14.5.4.5
Buffer Manager Reset Status Register, Section 14.5.4.9
317
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 14.12 Indirectly Accessible Switch Control and Status Registers (continued)
REGISTER #
SYMBOL
1C18h
BM_RATE_DRP_CNT_SRC_2
1C19h-1C1Fh
RESERVED
1C20h
BM_IMR
Buffer Manager Interrupt Mask Register, Section 14.5.4.26
1C21h
BM_IPR
Buffer Manager Interrupt Pending Register, Section 14.5.4.27
1C22h-FFFFh
RESERVED
Revision 2.0 (02-14-13)
REGISTER NAME
Buffer Manager Port 2 Ingress Rate Drop Count Register,
Section 14.5.4.25
Reserved for Future Use
Reserved for Future Use
318
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.1
General Switch CSRs
This section details the general switch fabric CSRs. These registers control the main reset and
interrupt functions of the switch fabric. A list of the general switch CSRs and their corresponding
register numbers is included in Table 14.12.
14.5.1.1
Switch Device ID Register (SW_DEV_ID)
Register #:
0000h
Size:
32 bits
This read-only register contains switch device ID information, including the device type, chip version
and revision codes.
BITS
DESCRIPTION
TYPE
DEFAULT
31:24
RESERVED
RO
-
23:16
Device Type Code (DEVICE_TYPE)
RO
03h
15:8
Chip Version Code (CHIP_VERSION)
RO
04h
7:0
Revision Code (REVISION)
RO
07h
SMSC LAN9312
319
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.1.2
Switch Reset Register (SW_RESET)
Register #:
0001h
Size:
32 bits
This register contains the switch fabric global reset. Refer to Section 4.2, "Resets," on page 36 for
more information.
BITS
31:1
0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Switch Fabric Reset (SW_RESET)
This bit is the global switch fabric reset. All switch fabric blocks are affected.
This bit must be manually cleared.
WO
0b
Revision 2.0 (02-14-13)
320
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.1.3
Switch Global Interrupt Mask Register (SW_IMR)
Register #:
0004h
Size:
32 bits
This read/write register contains the global interrupt mask for the switch fabric interrupts. All switch
related interrupts in the Switch Global Interrupt Pending Register (SW_IPR) may be masked via this
register. An interrupt is masked by setting the corresponding bit of this register. Clearing a bit will
unmask the interrupt. When an unmasked switch fabric interrupt is generated in the Switch Global
Interrupt Pending Register (SW_IPR), the interrupt will trigger the SWITCH_INT bit in the Interrupt
Status Register (INT_STS). Refer to Chapter 5, "System Interrupts," on page 49 for more information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:9
RESERVED
RO
-
8:7
RESERVED
R/W
11b
Note:
These bits must be written as 11b
6
Buffer Manager Interrupt Mask (BM)
When set, prevents the generation of switch fabric interrupts due to the
Buffer Manager via the Buffer Manager Interrupt Pending Register
(BM_IPR). The status bits in the SW_IPR register are not affected.
R/W
1b
5
Switch Engine Interrupt Mask (SWE)
When set, prevents the generation of switch fabric interrupts due to the
Switch Engine via the Switch Engine Interrupt Pending Register (SWE_IPR).
The status bits in the SW_IPR register are not affected.
R/W
1b
RESERVED
R/W
11b
4:3
Note:
These bits must be written as 11b
2
Port 2 MAC Interrupt Mask (MAC_2)
When set, prevents the generation of switch fabric interrupts due to the Port
2 MAC via the MAC_IPR_2 register (see Section 14.5.2.44, on page 366).
The status bits in the SW_IPR register are not affected.
R/W
1b
1
Port 1 MAC Interrupt Mask (MAC_1)
When set, prevents the generation of switch fabric interrupts due to the Port
1 MAC via the MAC_IPR_1 register (see Section 14.5.2.44, on page 366).
The status bits in the SW_IPR register are not affected.
R/W
1b
0
Port 0 MAC Interrupt Mask (MAC_MII)
When set, prevents the generation of switch fabric interrupts due to the Port
0 MAC via the MAC_IPR_MII register (see Section 14.5.2.44, on page 366).
The status bits in the SW_IPR register are not affected.
R/W
1b
SMSC LAN9312
321
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.1.4
Switch Global Interrupt Pending Register (SW_IPR)
Register #:
0005h
Size:
32 bits
This read-only register contains the pending global interrupts for the switch fabric. A set bit indicates
an unmasked bit in the corresponding switch fabric sub-system has been triggered. All switch related
interrupts in this register may be masked via the Switch Global Interrupt Mask Register (SW_IMR)
register. When an unmasked switch fabric interrupt is generated in this register, the interrupt will trigger
the SWITCH_INT bit in the Interrupt Status Register (INT_STS). Refer to Chapter 5, "System
Interrupts," on page 49 for more information.
BITS
TYPE
DEFAULT
RESERVED
RO
-
6
Buffer Manager Interrupt (BM)
Set when any unmasked bit in the Buffer Manager Interrupt Pending
Register (BM_IPR) is triggered. This bit is cleared upon a read.
RC
0b
5
Switch Engine Interrupt (SWE)
Set when any unmasked bit in the Switch Engine Interrupt Pending Register
(SWE_IPR) is triggered. This bit is cleared upon a read.
RC
0b
RESERVED
RO
-
2
Port 2 MAC Interrupt (MAC_2)
Set when any unmasked bit in the MAC_IPR_2 register (see Section
14.5.2.44, on page 366) is triggered. This bit is cleared upon a read.
RC
0b
1
Port 1 MAC Interrupt (MAC_1)
Set when any unmasked bit in the MAC_IPR_1 register (see Section
14.5.2.44, on page 366) is triggered. This bit is cleared upon a read.
RC
0b
0
Port 0 MAC Interrupt (MAC_MII)
Set when any unmasked bit in the MAC_IPR_MII register (see Section
14.5.2.44, on page 366) is triggered. This bit is cleared upon a read.
RC
0b
31:7
4:3
DESCRIPTION
Revision 2.0 (02-14-13)
322
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2
Switch Port 0, Port 1, and Port 2 CSRs
This section details the switch Port 0(Host MAC), Port 1, and Port 2 CSRs. Each port provides a
functionally identical set of registers which allow for the configuration of port settings, interrupts, and
the monitoring of the various packet counters.
Because the Port 0, Port 1, and Port 2 CSRs are functionally identical, their register descriptions have
been consolidated. A lowercase “x” has been appended to the end of each switch port register name
in this section, where “x” should be replaced with “MII”, “1”, or “2” for the Port 0, Port 1, or Port 2
registers respectively. A list of the Switch Port 0, Port 1, and Port 2 registers and their corresponding
register numbers is included in Table 14.12.
14.5.2.1
Port x MAC Version ID Register (MAC_VER_ID_x)
Register #:
Port0: 0400h
Port1: 0800h
Port2: 0C00h
Size:
32 bits
This read-only register contains switch device ID information, including the device type, chip version
and revision codes.
BITS
TYPE
DEFAULT
RESERVED
RO
-
11:8
Device Type Code (DEVICE_TYPE)
RO
5h
7:4
Chip Version Code (CHIP_VERSION)
RO
8h
3:0
Revision Code (REVISION)
RO
3h
31:12
DESCRIPTION
SMSC LAN9312
323
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.2
Port x MAC Receive Configuration Register (MAC_RX_CFG_x)
Register #:
Port0: 0401h
Port1: 0801h
Port2: 0C01h
Size:
32 bits
This read/write register configures the packet type passing parameters of the port.
BITS
DESCRIPTION
TYPE
DEFAULT
31:8
RESERVED
RO
-
7
RESERVED
R/W
0b
Note:
This bit must always be written as 0.
6
RESERVED
RO
-
5
Enable Receive Own Transmit
When set, the switch port will receive its own transmission if it is looped back
from the PHY. Normally, this function is only used in Half Duplex PHY
loopback.
R/W
0b
4
RESERVED
RO
-
3
Jumbo2K
When set, the maximum packet size accepted is 2048 bytes. Statistics
boundaries are also adjusted.
R/W
0b
2
RESERVED
RO
-
1
Reject MAC Types
When set, MAC control frames (packets with a type field of 8808h) are
filtered. When cleared, MAC Control frames, other than MAC Control Pause
frames, are sent to the forwarding process. MAC Control Pause frames are
always consumed by the switch.
R/W
1b
0
RX Enable
When set, the receive port is enabled. When cleared, the receive port is
disabled.
R/W
1b
Revision 2.0 (02-14-13)
324
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.3
Port x MAC Receive Undersize Count Register (MAC_RX_UNDSZE_CNT_x)
Register #:
Port0: 0410h
Port1: 0810h
Port2: 0C10h
Size:
32 bits
This register provides a counter of undersized packets received by the port. The counter is cleared
upon being read.
BITS
31:0
DESCRIPTION
RX Undersize
Count of packets that have less than 64 byte and a valid FCS.
Note:
SMSC LAN9312
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 115 hours.
325
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.4
Port x MAC Receive 64 Byte Count Register (MAC_RX_64_CNT_x)
Register #:
Port0: 0411h
Port1: 0811h
Port2: 0C11h
Size:
32 bits
This register provides a counter of 64 byte packets received by the port. The counter is cleared upon
being read.
BITS
31:0
DESCRIPTION
RX 64 Bytes
Count of packets (including bad packets) that have exactly 64 bytes.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Note: A bad packet is defined as a packet that has an FCS or Symbol error. For this counter, a packet
that is not an integral number of bytes is rounded down to the nearest byte.
Revision 2.0 (02-14-13)
326
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.5
Port x MAC Receive 65 to 127 Byte Count Register (MAC_RX_65_TO_127_CNT_x)
Register #:
Port0: 0412h
Port1: 0812h
Port2: 0C12h
Size:
32 bits
This register provides a counter of received packets between the size of 65 to 127 bytes. The counter
is cleared upon being read.
BITS
31:0
DESCRIPTION
RX 65 to 127 Bytes
Count of packets (including bad packets) that have between 65 and 127
bytes.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 487 hours.
Note: A bad packet is defined as a packet that has an FCS or Symbol error. For this counter, a packet
that is not an integral number of bytes is rounded down to the nearest byte.
SMSC LAN9312
327
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.6
Port x MAC Receive 128 to 255 Byte Count Register (MAC_RX_128_TO_255_CNT_x)
Register #:
Port0: 0413h
Port1: 0813h
Port2: 0C13h
Size:
32 bits
This register provides a counter of received packets between the size of 128 to 255 bytes. The counter
is cleared upon being read.
BITS
31:0
DESCRIPTION
RX 128 to 255 Bytes
Count of packets (including bad packets) that have between 128 and 255
bytes.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 848 hours.
Note: A bad packet is defined as a packet that has an FCS or Symbol error. For this counter, a packet
that is not an integral number of bytes is rounded down to the nearest byte.
Revision 2.0 (02-14-13)
328
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.7
Port x MAC Receive 256 to 511 Byte Count Register (MAC_RX_256_TO_511_CNT_x)
Register #:
Port0: 0414h
Port1: 0814h
Port2: 0C14h
Size:
32 bits
This register provides a counter of received packets between the size of 256 to 511 bytes. The counter
is cleared upon being read.
BITS
31:0
DESCRIPTION
RX 256 to 511 Bytes
Count of packets (including bad packets) that have between 256 and 511
bytes.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 1581 hours.
Note: A bad packet is defined as a packet that has an FCS or Symbol error. For this counter, a packet
that is not an integral number of bytes is rounded down to the nearest byte.
SMSC LAN9312
329
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.8
Port x MAC Receive 512 to 1023 Byte Count Register (MAC_RX_512_TO_1023_CNT_x)
Register #:
Port0: 0415h
Port1: 0815h
Port2: 0C15h
Size:
32 bits
This register provides a counter of received packets between the size of 512 to 1023 bytes. The
counter is cleared upon being read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
RX 512 to 1023 Bytes
Count of packets (including bad packets) that have between 512 and 1023
bytes.
RC
00000000h
Note:
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 3047 hours.
Note: A bad packet is defined as a packet that has an FCS or Symbol error. For this counter, a packet
that is not an integral number of bytes is rounded down to the nearest byte.
Revision 2.0 (02-14-13)
330
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.9
Port x MAC Receive 1024 to Max Byte Count Register (MAC_RX_1024_TO_MAX_CNT_x)
Register #:
Port0: 0416h
Port1: 0816h
Port2: 0C16h
Size:
32 bits
This register provides a counter of received packets between the size of 1024 to the maximum
allowable number bytes. The counter is cleared upon being read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
RX 1024 to Max Bytes
Count of packets (including bad packets) that have between 1024 and the
maximum allowable number of bytes. The max number of bytes is 1518 for
untagged packets and 1522 for tagged packets. If Jumbo2K (bit 3) is set in
the Port x MAC Receive Configuration Register (MAC_RX_CFG_x), the max
number of bytes is 2048.
RC
00000000h
Note:
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 5979 hours.
Note: A bad packet is defined as a packet that has an FCS or Symbol error. For this counter, a packet
with the maximum number of bytes that is not an integral number of bytes (e.g. a 1518 1/2
byte packet) is counted.
SMSC LAN9312
331
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.10
Port x MAC Receive Oversize Count Register (MAC_RX_OVRSZE_CNT_x)
Register #:
Port0: 0417h
Port1: 0817h
Port2: 0C17h
Size:
32 bits
This register provides a counter of received packets with a size greater than the maximum byte size.
The counter is cleared upon being read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
RX Oversize
Count of packets that have more than the maximum allowable number of
bytes and a valid FCS. The max number of bytes is 1518 for untagged
packets and 1522 for tagged packets. If Jumbo2K (bit 3) is set in the Port x
MAC Receive Configuration Register (MAC_RX_CFG_x), the max number
of bytes is 2048.
RC
00000000h
Note:
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 8813 hours.
Note: For this counter, a packet with the maximum number of bytes that is not an integral number of
bytes (e.g. a 1518 1/2 byte packet) is not considered oversize.
Revision 2.0 (02-14-13)
332
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.11
Port x MAC Receive OK Count Register (MAC_RX_PKTOK_CNT_x)
Register #:
Port0: 0418h
Port1: 0818h
Port2: 0C18h
Size:
32 bits
This register provides a counter of received packets that are or proper length and are free of errors.
The counter is cleared upon being read.
BITS
31:0
DESCRIPTION
RX OK
Count of packets that are of proper length and are free of errors.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Note: A bad packet is one that has a FCS or Symbol error.
SMSC LAN9312
333
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.12
Port x MAC Receive CRC Error Count Register (MAC_RX_CRCERR_CNT_x)
Register #:
Port0: 0419h
Port1: 0819h
Port2: 0C19h
Size:
32 bits
This register provides a counter of received packets that with CRC errors. The counter is cleared upon
being read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
RX CRC
Count of packets that have between 64 and the maximum allowable number
of bytes and have a bad FCS, but do not have an extra nibble. The max
number of bytes is 1518 for untagged packets and 1522 for tagged packets.
If Jumbo2K (bit 3) is set in the Port x MAC Receive Configuration Register
(MAC_RX_CFG_x), the max number of bytes is 2048.
RC
00000000h
Note:
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 137 hours.
Revision 2.0 (02-14-13)
334
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.13
Port x MAC Receive Multicast Count Register (MAC_RX_MULCST_CNT_x)
Register #:
Port0: 041Ah
Port1: 081Ah
Port2: 0C1Ah
Size:
32 bits
This register provides a counter of valid received packets with a multicast destination address. The
counter is cleared upon being read.
BITS
31:0
DESCRIPTION
RX Multicast
Count of good packets (proper length and free of errors), including MAC
control frames, that have a multicast destination address (not including
broadcasts).
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Note: A bad packet is one that has a FCS or Symbol error.
SMSC LAN9312
335
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.14
Port x MAC Receive Broadcast Count Register (MAC_RX_BRDCST_CNT_x)
Register #:
Port0: 041Bh
Port1: 081Bh
Port2: 0C1Bh
Size:
32 bits
This register provides a counter of valid received packets with a broadcast destination address. The
counter is cleared upon being read.
BITS
31:0
DESCRIPTION
RX Broadcast
Count of valid packets (proper length and free of errors) that have a
broadcast destination address.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Note: A bad packet is one that has a FCS or Symbol error.
Revision 2.0 (02-14-13)
336
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.15
Port x MAC Receive Pause Frame Count Register (MAC_RX_PAUSE_CNT_x)
Register #:
Port0: 041Ch
Port1: 081Ch
Port2: 0C1Ch
Size:
32 bits
This register provides a counter of valid received pause frame packets. The counter is cleared upon
being read.
BITS
31:0
DESCRIPTION
RX Pause Frame
Count of valid packets (proper length and free of errors) that have a type
field of 8808h and an op-code of 0001(Pause).
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Note: A bad packet is one that has a FCS or Symbol error.
SMSC LAN9312
337
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.16
Port x MAC Receive Fragment Error Count Register (MAC_RX_FRAG_CNT_x)
Register #:
Port0: 041Dh
Port1: 081Dh
Port2: 0C1Dh
Size:
32 bits
This register provides a counter of received packets of less than 64 bytes and a FCS error. The counter
is cleared upon being read.
BITS
31:0
DESCRIPTION
RX Fragment
Count of packets that have less than 64 bytes and a FCS error.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 115 hours.
Revision 2.0 (02-14-13)
338
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.17
Port x MAC Receive Jabber Error Count Register (MAC_RX_JABB_CNT_x)
Register #:
Port0: 041Eh
Port1: 081Eh
Port2: 0C1Eh
Size:
32 bits
This register provides a counter of received packets with greater than the maximum allowable number
of bytes and a FCS error. The counter is cleared upon being read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
RX Jabber
Count of packets that have more than the maximum allowable number of
bytes and a FCS error. The max number of bytes is 1518 for untagged
packets and 1522 for tagged packets. If Jumbo2K (bit 3) is set in the Port x
MAC Receive Configuration Register (MAC_RX_CFG_x), the max number
of bytes is 2048.
RC
00000000h
Note:
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 8813 hours.
Note: For this counter, a packet with the maximum number of bytes that is not an integral number of
bytes (e.g. a 1518 1/2 byte packet) and contains a FCS error is not considered jabber and is
not counted here.
SMSC LAN9312
339
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.18
Port x MAC Receive Alignment Error Count Register (MAC_RX_ALIGN_CNT_x)
Register #:
Port0: 041Fh
Port1: 081Fh
Port2: 0C1Fh
Size:
32 bits
This register provides a counter of received packets with 64 bytes to the maximum allowable, and a
FCS error. The counter is cleared upon being read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
RX Alignment
Count of packets that have between 64 bytes and the maximum allowable
number of bytes and are not byte aligned and have a bad FCS. The max
number of bytes is 1518 for untagged packets and 1522 for tagged packets.
If Jumbo2K (bit 3) is set in the Port x MAC Receive Configuration Register
(MAC_RX_CFG_x), the max number of bytes is 2048.
RC
00000000h
Note:
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Note: For this counter, a packet with the maximum number of bytes that is not an integral number of
bytes (e.g. a 1518 1/2 byte packet) and a FCS error is considered an alignment error and is
counted.
Revision 2.0 (02-14-13)
340
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.19
Port x MAC Receive Packet Length Count Register (MAC_RX_PKTLEN_CNT_x)
Register #:
Port0: 0420h
Port1: 0820h
Port2: 0C20h
Size:
32 bits
This register provides a counter of total bytes received. The counter is cleared upon being read.
BITS
31:0
DESCRIPTION
RX Bytes
Count of total bytes received (including bad packets).
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 5.8 hours.
Note: If necessary, for oversized packets, the packet is either truncated at 1518 bytes (untagged,
Jumbo2K=0), 1522 bytes (tagged, Jumbo2K=0), or 2048 bytes (Jumbo2K=1). If this occurs,
the byte count recorded is 1518, 1522, or 2048, respectively. The Jumbo2K bit is located in
the Port x MAC Receive Configuration Register (MAC_RX_CFG_x).
Note: A bad packet is one that has an FCS or Symbol error. For this counter, a packet that is not an
integral number of bytes (e.g. a 1518 1/2 byte packet) is rounded down to the nearest byte.
SMSC LAN9312
341
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.20
Port x MAC Receive Good Packet Length Count Register (MAC_RX_GOODPKTLEN_CNT_x)
Register #:
Port0: 0421h
Port1: 0821h
Port2: 0C21h
Size:
32 bits
This register provides a counter of total bytes received in good packets. The counter is cleared upon
being read.
BITS
31:0
DESCRIPTION
RX Good Bytes
Count of total bytes received in good packets (proper length and free of
errors).
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 5.8 hours.
Note: A bad packet is one that has an FCS or Symbol error.
Revision 2.0 (02-14-13)
342
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.21
Port x MAC Receive Symbol Error Count Register (MAC_RX_SYMBOL_CNT_x)
Register #:
Port0: 0422h
Port1: 0822h
Port2: 0C22h
Size:
32 bits
This register provides a counter of received packets with a symbol error. The counter is cleared upon
being read.
BITS
31:0
DESCRIPTION
RX Symbol
Count of packets that had a receive symbol error.
Note:
SMSC LAN9312
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 115 hours.
343
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.22
Port x MAC Receive Control Frame Count Register (MAC_RX_CTLFRM_CNT_x)
Register #:
Port0: 0423h
Port1: 0823h
Port2: 0C23h
Size:
32 bits
This register provides a counter of good packets with a type field of 8808h. The counter is cleared
upon being read.
BITS
31:0
DESCRIPTION
RX Control Frame
Count of good packets (proper length and free of errors) that have a type
field of 8808h.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Note: A bad packet is one that has an FCS or Symbol error.
Revision 2.0 (02-14-13)
344
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.23
Port x MAC Transmit Configuration Register (MAC_TX_CFG_x)
Register #:
Port0: 0440h
Port1: 0840h
Port2: 0C40h
Size:
32 bits
This read/write register configures the transmit packet parameters of the port.
BITS
31:8
7
6:2
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
MAC Counter Test
When set, TX and RX counters that normally clear to 0 when read, will be
set to 7FFF_FFFCh when read with the exception of the Port x MAC
Receive Packet Length Count Register (MAC_RX_PKTLEN_CNT_x), Port x
MAC Transmit Packet Length Count Register (MAC_TX_PKTLEN_CNT_x),
and Port x MAC Receive Good Packet Length Count Register
(MAC_RX_GOODPKTLEN_CNT_x) counters which will be set to
7FFF_FF80h.
R/W
0b
IFG Config
These bits control the transmit inter-frame gap.
IFG bit times = (IFG Config *4) + 12
R/W
10101b
Note:
IFG Config values less than 15 are unsupported.
1
TX Pad Enable
When set, packets shorter than 64 bytes are padded with zeros if needed
and a FCS is appended. Packets that are 60 bytes or less will become 64
bytes. Packets that are 61, 62, and 63 bytes will become 65, 66, and 67
bytes respectively.
R/W
1b
0
TX Enable
When set, the transmit port is enabled. When cleared, the transmit port is
disabled.
R/W
1b
SMSC LAN9312
345
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.24
Port x MAC Transmit Flow Control Settings Register (MAC_TX_FC_SETTINGS_x)
Register #:
Port0: 0441h
Port1: 0841h
Port2: 0C41h
Size:
32 bits
This read/write register configures the flow control settings of the port.
BITS
DESCRIPTION
TYPE
DEFAULT
31:18
RESERVED
RO
-
17:16
Backoff Reset RX/TX
Half duplex-only. Determines when the truncated binary exponential backoff
attempts counter is reset.
R/W
00b
R/W
FFFFh
00 = Reset on successful transmission (IEEE standard)
01 = Reset on successful reception
1X = Reset on either successful transmission or reception
15:0
Pause Time Value
The value that is inserted into the transmitted pause packet when the switch
wants to “XOFF” its link partner.
Revision 2.0 (02-14-13)
346
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.25
Port x MAC Transmit Deferred Count Register (MAC_TX_DEFER_CNT_x)
Register #:
Port0: 0451h
Port1: 0851h
Port2: 0C51h
Size:
32 bits
This register provides a counter deferred packets. The counter is cleared upon being read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
TX Deferred
Count of packets that were available for transmission but were deferred on
the first transmit attempt due to network traffic (either on receive or prior
transmission). This counter is not incremented on collisions. This counter is
incremented only in half-duplex operation.
RC
00000000h
Note:
SMSC LAN9312
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
347
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.26
Port x MAC Transmit Pause Count Register (MAC_TX_PAUSE_CNT_x)
Register #:
Port0: 0452h
Port1: 0852h
Port2: 0C52h
Size:
32 bits
This register provides a counter of transmitted pause packets. The counter is cleared upon being read.
BITS
31:0
DESCRIPTION
TX Pause
Count of pause packets transmitted.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Revision 2.0 (02-14-13)
348
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.27
Port x MAC Transmit OK Count Register (MAC_TX_PKTOK_CNT_x)
Register #:
Port0: 0453h
Port1: 0853h
Port2: 0C53h
Size:
32 bits
This register provides a counter of successful transmissions. The counter is cleared upon being read.
BITS
31:0
DESCRIPTION
TX OK
Count of successful transmissions. Undersize packets are not included in
this count.
Note:
SMSC LAN9312
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
349
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.28
Port x MAC Transmit 64 Byte Count Register (MAC_TX_64_CNT_x)
Register #:
Port0: 0454h
Port1: 0854h
Port2: 0C54h
Size:
32 bits
This register provides a counter of 64 byte packets transmitted by the port. The counter is cleared
upon being read.
BITS
DESCRIPTION
31:0
TX 64 Bytes
Count of packets that have exactly 64 bytes.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Revision 2.0 (02-14-13)
350
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.29
Port x MAC Transmit 65 to 127 Byte Count Register (MAC_TX_65_TO_127_CNT_x)
Register #:
Port0: 0455h
Port1: 0855h
Port2: 0C55h
Size:
32 bits
This register provides a counter of transmitted packets between the size of 65 to 127 bytes. The
counter is cleared upon being read.
BITS
31:0
DESCRIPTION
TX 65 to 127 Bytes
Count of packets that have between 65 and 127 bytes.
Note:
SMSC LAN9312
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 487 hours.
351
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.30
Port x MAC Transmit 128 to 255 Byte Count Register (MAC_TX_128_TO_255_CNT_x)
Register #:
Port0: 0456h
Port1: 0856h
Port2: 0C56h
Size:
32 bits
This register provides a counter of transmitted packets between the size of 128 to 255 bytes. The
counter is cleared upon being read.
BITS
31:0
DESCRIPTION
TX 128 to 255 Bytes
Count of packets that have between 128 and 255 bytes.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 848 hours.
Revision 2.0 (02-14-13)
352
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.31
Port x MAC Transmit 256 to 511 Byte Count Register (MAC_TX_256_TO_511_CNT_x)
Register #:
Port0: 0457h
Port1: 0857h
Port2: 0C57h
Size:
32 bits
This register provides a counter of transmitted packets between the size of 256 to 511 bytes. The
counter is cleared upon being read.
BITS
31:0
DESCRIPTION
TX 256 to 511 Bytes
Count of packets that have between 256 and 511 bytes.
Note:
SMSC LAN9312
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 1581 hours.
353
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.32
Port x MAC Transmit 512 to 1023 Byte Count Register (MAC_TX_512_TO_1023_CNT_x)
Register #:
Port0: 0458h
Port1: 0858h
Port2: 0C58h
Size:
32 bits
This register provides a counter of transmitted packets between the size of 512 to 1023 bytes. The
counter is cleared upon being read.
BITS
31:0
DESCRIPTION
TX 512 to 1023 Bytes
Count of packets that have between 512 and 1023 bytes.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 3047 hours.
Revision 2.0 (02-14-13)
354
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.33
Port x MAC Transmit 1024 to Max Byte Count Register (MAC_TX_1024_TO_MAX_CNT_x)
Register #:
Port0: 0459h
Port1: 0859h
Port2: 0C59h
Size:
32 bits
This register provides a counter of transmitted packets between the size of 1024 to the maximum
allowable number bytes. The counter is cleared upon being read.
BITS
31:0
DESCRIPTION
TX 1024 to Max Bytes
Count of packets that have more than 1024 bytes.
Note:
SMSC LAN9312
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 5979 hours.
355
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.34
Port x MAC Transmit Undersize Count Register (MAC_TX_UNDSZE_CNT_x)
Register #:
Port0: 045Ah
Port1: 085Ah
Port2: 0C5Ah
Size:
32 bits
This register provides a counter of undersized packets transmitted by the port. The counter is cleared
upon being read.
BITS
31:0
DESCRIPTION
TX Undersize
Count of packets that have less than 64 bytes.
Note:
This condition could occur when TX padding is disabled and a tag
is removed.
Note:
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 458 hours.
Revision 2.0 (02-14-13)
356
DATASHEET
TYPE
DEFAULT
RC
00000000h
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.35
Port x MAC Transmit Packet Length Count Register (MAC_TX_PKTLEN_CNT_x)
Register #:
Port0: 045Ch
Port1: 085Ch
Port2: 0C5Ch
Size:
32 bits
This register provides a counter of total bytes transmitted. The counter is cleared upon being read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
TX Bytes
Count of total bytes transmitted (does not include bytes from collisions, but
does include bytes from Pause packets).
RC
00000000h
Note:
SMSC LAN9312
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 5.8 hours.
357
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.36
Port x MAC Transmit Broadcast Count Register (MAC_TX_BRDCST_CNT_x)
Register #:
Port0: 045Dh
Port1: 085Dh
Port2: 0C5Dh
Size:
32 bits
This register provides a counter of transmitted broadcast packets. The counter is cleared upon being
read.
BITS
31:0
DESCRIPTION
TX Broadcast
Count of broadcast packets transmitted.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Revision 2.0 (02-14-13)
358
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.37
Port x MAC Transmit Multicast Count Register (MAC_TX_MULCST_CNT_x)
Register #:
Port0: 045Eh
Port1: 085Eh
Port2: 0C5Eh
Size:
32 bits
This register provides a counter of transmitted multicast packets. The counter is cleared upon being
read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
TX Multicast
Count of multicast packets transmitted including MAC Control Pause frames.
RC
00000000h
Note:
SMSC LAN9312
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
359
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.38
Port x MAC Transmit Late Collision Count Register (MAC_TX_LATECOL_CNT_x)
Register #:
Port0: 045Fh
Port1: 085Fh
Port2: 0C5Fh
Size:
32 bits
This register provides a counter of transmitted packets which experienced a late collision. The counter
is cleared upon being read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
TX Late Collision
Count of transmitted packets that experienced a late collision. This counter
is incremented only in half-duplex operation.
RC
00000000h
Note:
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Revision 2.0 (02-14-13)
360
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.39
Port x MAC Transmit Excessive Collision Count Register (MAC_TX_EXCCOL_CNT_x)
Register #:
Port0: 0460h
Port1: 0860h
Port2: 0C60h
Size:
32 bits
This register provides a counter of transmitted packets which experienced 16 collisions. The counter
is cleared upon being read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
TX Excessive Collision
Count of transmitted packets that experienced 16 collisions. This counter is
incremented only in half-duplex operation.
RC
00000000h
Note:
SMSC LAN9312
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 1466 hours.
361
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.40
Port x MAC Transmit Single Collision Count Register (MAC_TX_SNGLECOL_CNT_x)
Register #:
Port0: 0461h
Port1: 0861h
Port2: 0C61h
Size:
32 bits
This register provides a counter of transmitted packets which experienced exactly 1 collision. The
counter is cleared upon being read.
BITS
31:0
DESCRIPTION
TX Excessive Collision
Count of transmitted packets that experienced exactly 1 collision. This
counter is incremented only in half-duplex operation.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 573 hours.
Revision 2.0 (02-14-13)
362
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.41
Port x MAC Transmit Multiple Collision Count Register (MAC_TX_MULTICOL_CNT_x)
Register #:
Port0: 0462h
Port1: 0862h
Port2: 0C62h
Size:
32 bits
This register provides a counter of transmitted packets which experienced between 2 and 15 collisions.
The counter is cleared upon being read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
TX Excessive Collision
Count of transmitted packets that experienced between 2 and 15 collisions.
This counter is incremented only in half-duplex operation.
RC
00000000h
Note:
SMSC LAN9312
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 664 hours.
363
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.42
Port x MAC Transmit Total Collision Count Register (MAC_TX_TOTALCOL_CNT_x)
Register #:
Port0: 0463h
Port1: 0863h
Port2: 0C63h
Size:
32 bits
This register provides a counter of total collisions including late collisions. The counter is cleared upon
being read.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
TX Total Collision
Total count of collisions including late collisions. This counter is incremented
only in half-duplex operation.
RC
00000000h
Note:
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 92 hours.
Revision 2.0 (02-14-13)
364
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.43
Port x MAC Interrupt Mask Register (MAC_IMR_x)
Register #:
Port0: 0480h
Port1: 0880h
Port2: 0C80h
Size:
32 bits
This register contains the Port x interrupt mask. Port x related interrupts in the Port x MAC Interrupt
Pending Register (MAC_IPR_x) may be masked via this register. An interrupt is masked by setting the
corresponding bit of this register. Clearing a bit will unmask the interrupt. Refer to Chapter 5, "System
Interrupts," on page 49 for more information.
Note: There are no possible Port x interrupt conditions available. This register exists for future use,
and should be configured as indicated for future compatibility.
BITS
DESCRIPTION
TYPE
DEFAULT
31:8
RESERVED
RO
-
7:0
RESERVED
R/W
11h
Note:
SMSC LAN9312
These bits must be written as 11h
365
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.2.44
Port x MAC Interrupt Pending Register (MAC_IPR_x)
Register #:
Port0: 0481h
Port1: 0881h
Port2: 0C81h
Size:
32 bits
This read-only register contains the pending Port x interrupts. A set bit indicates an interrupt has been
triggered. All interrupts in this register may be masked via the Port x MAC Interrupt Pending Register
(MAC_IPR_x) register. Refer to Chapter 5, "System Interrupts," on page 49 for more information.
Note: There are no possible Port x interrupt conditions available. This register exists for future use.
BITS
31:0
DESCRIPTION
RESERVED
Revision 2.0 (02-14-13)
366
DATASHEET
TYPE
DEFAULT
RO
-
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3
Switch Engine CSRs
This section details the switch engine related CSRs. These registers allow configuration and monitoring
of the various switch engine components including the ALR, VLAN, Port VID, and DIFFSERV tables.
A list of the general switch CSRs and their corresponding register numbers is included in Table 14.12.
14.5.3.1
Switch Engine ALR Command Register (SWE_ALR_CMD)
Register #:
1800h
Size:
32 bits
This register is used to manually read and write MAC addresses from/into the ALR table.
For a read access, the Switch Engine ALR Read Data 0 Register (SWE_ALR_RD_DAT_0) and Switch
Engine ALR Read Data 1 Register (SWE_ALR_RD_DAT_1) should be read following the setting of bit
1(Get First Entry) or bit 0(Get Next Entry) of this register.
For write access, the Switch Engine ALR Write Data 0 Register (SWE_ALR_WR_DAT_0) and Switch
Engine ALR Write Data 1 Register (SWE_ALR_WR_DAT_1) registers should first be written with the
MAC address, followed by the setting of bit 2(Make Entry) of this register. The Make Pending bit in the
Switch Engine ALR Command Status Register (SWE_ALR_CMD_STS) register indicates when the
command is finished.
Refer to Chapter 6, "Switch Fabric," on page 55 for more information.
BITS
TYPE
DEFAULT
RESERVED
RO
-
2
Make Entry
When set, the contents of ALR_WR_DAT_0 and ALR_WR_DAT_1 are
written into the ALR table. The ALR logic determines the location where the
entry is written. This command can also be used to change or delete a
previously written or automatically learned entry. This bit has no affect when
written low. This bit must be cleared once the ALR Make command is
completed, which can be determined by the ALR Status bit in the Switch
Engine ALR Command Status Register (SWE_ALR_CMD_STS) register.
R/W
0b
1
Get First Entry
When set, the ALR read pointer is reset to the beginning of the ALR table
and the ALR table is searched for the first valid entry, which is loaded into
the ALR_RD_DAT_0 and ALR_RD_DAT_1 registers. The bit has no affect
when written low. This bit must be cleared after it is set.
R/W
0b
0
Get Next Entry
When set, the next valid entry in the ALR MAC address table is loaded into
the ALR_RD_DAT_0 and ALR_RD_DAT_1 registers. This bit has no affect
when written low. This bit must be cleared after it is set.
R/W
0b
31:3
DESCRIPTION
SMSC LAN9312
367
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.2
Switch Engine ALR Write Data 0 Register (SWE_ALR_WR_DAT_0)
Register #:
1801h
Size:
32 bits
This register is used in conjunction with the Switch Engine ALR Write Data 1 Register
(SWE_ALR_WR_DAT_1) and contains the first 32 bits of ALR data to be manually written via the Make
Entry command in the Switch Engine ALR Command Register (SWE_ALR_CMD).
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
MAC Address
This field contains the first 32 bits of the ALR entry that will be written into
the ALR table. These bits correspond to the first 32 bits of the MAC address.
Bit 0 holds the LSB of the first byte (the multicast bit).
R/W
00000000h
Revision 2.0 (02-14-13)
368
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.3
Switch Engine ALR Write Data 1 Register (SWE_ALR_WR_DAT_1)
Register #:
1802h
Size:
32 bits
This register is used in conjunction with the Switch Engine ALR Write Data 0 Register
(SWE_ALR_WR_DAT_0) and contains the last 32 bits of ALR data to be manually written via the Make
Entry command in the Switch Engine ALR Command Register (SWE_ALR_CMD).
BITS
TYPE
DEFAULT
RESERVED
RO
-
24
Valid
When set, this bit makes the entry valid. It can be cleared to invalidate a
previous entry that contained the specified MAC address.
R/W
0b
23
Age/Override
This bit is used by the aging and forwarding processes.
R/W
0b
R/W
0b
Filter
When set, packets with a destination address that matches this MAC
address will be filtered.
R/W
0b
Priority
These bits specify the priority that is used for packets with a destination
address that matches this MAC address. This priority is only used if the
Static bit of this register is set, and the DA Highest Priority (bit 5) in the
Switch Engine Global Ingress Configuration Register
(SWE_GLOBAL_INGRSS_CFG) is set.
R/W
00b
31:25
DESCRIPTION
If the Static bit of this register is cleared, this bit should be set so that the
entry will age in the normal amount of time.
If the Static bit is set, this bit is used as a port state override bit. When set,
packets received with a destination address that matches the MAC address
in the SWE_ALR_WR_DAT_1 and SWE_ALR_WR_DAT_0 registers will be
forwarded regardless of the port state of the ingress or egress port(s). This
is typically used to allow the reception of BPDU packets in the nonforwarding state.
22
Static
When this bit is set, this entry will not be removed by the aging process
and/or be changed by the learning process. When this bit is cleared, this
entry will be automatically removed after 5 to 10 minutes of inactivity.
Inactivity is defined as no packets being received with a source address that
matches this MAC address.
Note:
21
20:19
SMSC LAN9312
This bit is normally set when adding manual entries. It must be
cleared when removing an entry (clearing the Valid bit).
369
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
18:16
Port
These bits indicate the port(s) associated with this MAC address. When bit
18 is cleared, a single port is selected. When bit 18 is set, multiple ports are
selected.
R/W
000b
R/W
0000h
15:0
VALUE
ASSOCIATED PORT(S)
000
Port 0(Host MAC)
001
Port 1
010
Port 2
011
RESERVED
100
Port 0(Host MAC) and Port 1
101
Port 0(Host MAC) and Port 2
110
Port 1 and Port 2
111
Port 0(Host MAC), Port 1, and Port 2
MAC Address
These field contains the last 16 bits of the ALR entry that will be written into
the ALR table. They correspond to the last 16 bits of the MAC address. Bit
15 holds the MSB of the last byte (the last bit on the wire). The first 32 bits
of the MAC address are located in the Switch Engine ALR Write Data 0
Register (SWE_ALR_WR_DAT_0).
Revision 2.0 (02-14-13)
370
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.4
Switch Engine ALR Read Data 0 Register (SWE_ALR_RD_DAT_0)
Register #:
1805h
Size:
32 bits
This register is used in conjunction with the Switch Engine ALR Read Data 1 Register
(SWE_ALR_RD_DAT_1) to read the ALR table. It contains the first 32 bits of the ALR entry and is
loaded via the Get First Entry or Get Next Entry commands in the Switch Engine ALR Command
Register (SWE_ALR_CMD). This register is only valid when either of the Valid or End of Table bits in
the Switch Engine ALR Read Data 1 Register (SWE_ALR_RD_DAT_1) are set.
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
MAC Address
This field contains the first 32 bits of the ALR entry. These bits correspond
to the first 32 bits of the MAC address. Bit 0 holds the LSB of the first byte
(the multicast bit).
RO
00000000h
SMSC LAN9312
371
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.5
Switch Engine ALR Read Data 1 Register (SWE_ALR_RD_DAT_1)
Register #:
1806h
Size:
32 bits
This register is used in conjunction with the Switch Engine ALR Read Data 0 Register
(SWE_ALR_RD_DAT_0) to read the ALR table. It contains the last 32 bits of the ALR entry and is
loaded via the Get First Entry or Get Next Entry commands in the Switch Engine ALR Command
Register (SWE_ALR_CMD). This register is only valid when either of the Valid or End of Table bits are
set.
BITS
TYPE
DEFAULT
RESERVED
RO
-
24
Valid
This bit is cleared when the Get First Entry or Get Next Entry bits of the
Switch Engine ALR Command Register (SWE_ALR_CMD) are written. This
bit is set when a valid entry is found in the ALR table. This bit stays cleared
when the top of the ALR table is reached without finding an entry.
RO
0b
23
End of Table
This bit indicates that the end of the ALR table has been reached and further
Get Next Entry commands are not required.
RO
0b
31:25
DESCRIPTION
Note:
The Valid bit may or may not be set when the end of the table is
reached.
22
Static
Indicates that this entry will not be removed by the aging process. When this
bit is cleared, this entry will be automatically removed after 5 to 10 minutes
of inactivity. Inactivity is defined as no packets being received with a source
address that matches this MAC address.
RO
0b
21
Filter
When set, indicates that packets with a destination address that matches
this MAC address will be filtered.
RO
0b
20:19
Priority
These bits indicate the priority that is used for packets with a destination
address that matches this MAC address. This priority is only used if the
Static bit of this register is set, and the DA Highest Priority (bit 5) in the
Switch Engine Global Ingress Configuration Register
(SWE_GLOBAL_INGRSS_CFG) register is set.
RO
00b
Revision 2.0 (02-14-13)
372
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
18:16
Port
These bits indicate the port(s) associated with this MAC address. When bit
18 is cleared, a single port is selected. When bit 18 is set, multiple ports are
selected.
RO
000b
RO
0000h
15:0
VALUE
ASSOCIATED PORT(S)
000
Port 0(Host MAC)
001
Port 1
010
Port 2
011
RESERVED
100
Port 0(Host MAC) and Port 1
101
Port 0(Host MAC) and Port 2
110
Port 1 and Port 2
111
Port 0(Host MAC), Port 1, and Port 2
MAC Address
These field contains the last 16 bits of the ALR entry. They correspond to
the last 16 bits of the MAC address. Bit 15 holds the MSB of the last byte
(the last bit on the wire). The first 32 bits of the MAC address are located
in the Switch Engine ALR Read Data 0 Register (SWE_ALR_RD_DAT_0).
SMSC LAN9312
373
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.6
Switch Engine ALR Command Status Register (SWE_ALR_CMD_STS)
Register #:
1808h
Size:
32 bits
This register indicates the current ALR command status.
BITS
TYPE
DEFAULT
RESERVED
RO
-
1
ALR Init Done
When set, indicates that the ALR table has finished being initialized by the
reset process. The initialization is performed upon any reset that resets the
switch fabric. The initialization takes approximately 20uS. During this time,
any received packet will be dropped. Software should monitor this bit before
writing any of the ALR tables or registers.
RO
SS
Note 14.62
0
Make Pending
When set, indicates that the Make Entry command is taking place. This bit
is cleared once the Make Entry command has finished.
RO
SC
0b
31:2
DESCRIPTION
Note 14.62 The default value of this bit is 0 immediately following any switch fabric reset and then selfsets to 1 once the ALR table is initialized.
Revision 2.0 (02-14-13)
374
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.7
Switch Engine ALR Configuration Register (SWE_ALR_CFG)
Register #:
1809h
Size:
32 bits
This register controls the ALR aging timer duration.
BITS
31:1
0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
ALR Age Test
When set, this bit decreases the aging timer from 5 minutes to 50mS.
R/W
0b
SMSC LAN9312
375
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.8
Switch Engine VLAN Command Register (SWE_VLAN_CMD)
Register #:
180Bh
Size:
32 bits
This register is used to read and write the VLAN or Port VID tables. A write to this address performs
the specified access.
For a read access, the Operation Pending bit in the Switch Engine VLAN Command Status Register
(SWE_VLAN_CMD_STS) indicates when the command is finished. The Switch Engine VLAN Read
Data Register (SWE_VLAN_RD_DATA) can then be read.
For a write access, the Switch Engine VLAN Write Data Register (SWE_VLAN_WR_DATA) register
should be written first. The Operation Pending bit in the Switch Engine VLAN Command Status
Register (SWE_VLAN_CMD_STS) indicates when the command is finished.
BITS
TYPE
DEFAULT
RESERVED
RO
-
5
VLAN RnW
This bit specifies a read(1) or a write(0) command.
R/W
0b
4
PVIDnVLAN
When set, this bit selects the Port VID table. When cleared, this bit selects
the VLAN table.
R/W
0b
VLAN/Port
This field specifies the VLAN(0-15) or port(0-2) to be read or written.
R/W
0h
31:6
3:0
DESCRIPTION
Note:
Values outside of the valid range may cause unexpected results.
Revision 2.0 (02-14-13)
376
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.9
Switch Engine VLAN Write Data Register (SWE_VLAN_WR_DATA)
Register #:
180Ch
Size:
32 bits
This register is used write the VLAN or Port VID tables.
BITS
DESCRIPTION
TYPE
DEFAULT
31:18
RESERVED
RO
-
17:0
Port Default VID and Priority
When the port VID table is selected (PVIDnVLAN=1 of the Switch Engine
VLAN Command Register (SWE_VLAN_CMD)), bits 11:0 of this field specify
the default VID for the port and bits 14:12 specify the default priority. All
other bits of this field are reserved. These bits are used when a packet is
received without a VLAN tag or with a NULL VLAN ID. By default, the VID
and priority for all three ports is 0.
R/W
0b
Note:
Values of 0 and FFFh should not be used since they are special
VLAN IDs per the IEEE 802.3Q specification.
VLAN Data
When the VLAN table is selected (PVIDnVLAN=0 of the Switch Engine
VLAN Command Register (SWE_VLAN_CMD)), the bits form the VLAN
table entry as follows:
BITS
17
DESCRIPTION
DEFAULT
Member Port 2
Indicates the configuration of Port 2 for this VLAN entry.
0b
1 = Member - Packets with a VID that matches this entry
are allowed on ingress. The port is a member of the
broadcast domain on egress.
0 = Not a Member - Packets with a VID that matches this
entry are filtered on ingress unless the Admit Non Member
bit in the Switch Engine Admit Non Member Register
(SWE_ADMT_N_MEMBER) is set for this port. The port is
not a member of the broadcast domain on egress.
16
Un-Tag Port 2
When this bit is set, packets received on Port 2 with a VID
that matches this entry will have their tag removed when retransmitted by egress ports that are designated as Hybrid
ports via the Buffer Manager Egress Port Type Register
(BM_EGRSS_PORT_TYPE).
0b
15
Member Port 1
See description for Member Port 2.
0b
14
Un-Tag Port 1
See description for Un-Tag Port 2.
0b
13
Member Port 0 (Host MAC)
See description for Member Port 2.
0b
12
Un-Tag Port 0 (Host MAC)
See description for Un-Tag Port 2.
0b
11:0
VID
These bits specify the VLAN ID associated with this VLAN
entry.
000h
To disable a VLAN entry, a value of 0 should be used.
Note:
A value of 0 is considered a NULL VLAN and
should not normally be used other than to
disable a VLAN entry.
Note:
SMSC LAN9312
A value of 3FFh is considered reserved by IEEE
802.1Q and should not be used.
377
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.10
Switch Engine VLAN Read Data Register (SWE_VLAN_RD_DATA)
Register #:
180Eh
Size:
32 bits
This register is used to read the VLAN or Port VID tables.
BITS
DESCRIPTION
TYPE
DEFAULT
31:18
RESERVED
RO
-
17:0
Port Default VID and Priority
When the port VID table is selected (PVIDnVLAN=1 of the Switch Engine
VLAN Command Register (SWE_VLAN_CMD)), bits 11:0 of this field specify
the default VID for the port and bits 14:12 specify the default priority. All
other bits of this field are reserved. These bits are used when a packet is
received without a VLAN tag or with a NULL VLAN ID. By default, the VID
and priority for all three ports is 0.
RO
00000h
VLAN Data
When the VLAN table is selected (PVIDnVLAN=0 of the Switch Engine
VLAN Command Register (SWE_VLAN_CMD)), the bits form the VLAN
table entry as follows:
BITS
17
DESCRIPTION
DEFAULT
Member Port 2
Indicates the configuration of Port 2 for this VLAN entry.
0b
1 = Member - Packets with a VID that matches this entry
are allowed on ingress. The port is a member of the
broadcast domain on egress.
0 = Not a Member - Packets with a VID that matches this
entry are filtered on ingress unless the Admit Non Member
bit in the Switch Engine Admit Non Member Register
(SWE_ADMT_N_MEMBER) is set for this port. The port is
not a member of the broadcast domain on egress.
16
Un-Tag Port 2
When this bit is set, packets received on Port 2 with a VID
that matches this entry will have their tag removed when retransmitted by egress ports that are designated as Hybrid
ports via the Buffer Manager Egress Port Type Register
(BM_EGRSS_PORT_TYPE).
0b
15
Member Port 1
See description for Member Port 2.
0b
14
Un-Tag Port 1
See description for Un-Tag Port 2.
0b
13
Member Port 0 (Host MAC)
See description for Member Port 2.
0b
12
Un-Tag Port 0 (Host MAC)
See description for Un-Tag Port 2.
0b
11:0
Revision 2.0 (02-14-13)
VID
These bits specify the VLAN ID associated with this VLAN
entry.
378
DATASHEET
000h
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.11
Switch Engine VLAN Command Status Register (SWE_VLAN_CMD_STS)
Register #:
1810h
Size:
32 bits
This register indicates the current VLAN command status.
BITS
31:1
0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Operation Pending
When set, this bit indicates that the read or write command is taking place.
This bit is cleared once the command has finished.
RO
SC
0b
SMSC LAN9312
379
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.12
Switch Engine DIFFSERV Table Command Register (SWE_DIFFSERV_TBL_CFG)
Register #:
1811h
Size:
32 bits
This register is used to read and write the DIFFSERV table. A write to this address performs the
specified access. This table is used to map the received IP ToS/CS to a priority.
For a read access, the Operation Pending bit in the Switch Engine DIFFSERV Table Command Status
Register (SWE_DIFFSERV_TBL_CMD_STS) indicates when the command is finished. The Switch
Engine DIFFSERV Table Read Data Register (SWE_DIFFSERV_TBL_RD_DATA) can then be read.
F o r a w r i t e a c c e s s , t h e S w i t c h E n g i n e D I F F S E R V Ta b l e W r i t e D a t a R e g i s t e r
(SWE_DIFFSERV_TBL_WR_DATA) register should be written first. The Operation Pending bit in the
Switch Engine DIFFSERV Table Command Status Register (SWE_DIFFSERV_TBL_CMD_STS)
indicates when the command is finished.
BITS
TYPE
DEFAULT
RESERVED
RO
-
7
DIFFSERV Table RnW
This bit specifies a read(1) or a write(0) command.
R/W
0b
6
RESERVED
RO
-
DIFFSERV Table Index
This field specifies the ToS/CS entry that is accessed.
R/W
0h
31:8
5:0
DESCRIPTION
Revision 2.0 (02-14-13)
380
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.13
Switch Engine DIFFSERV Table Write Data Register (SWE_DIFFSERV_TBL_WR_DATA)
Register #:
1812h
Size:
32 bits
This register is used to write the DIFFSERV table. The DIFFSERV table is not initialized upon reset
on power-up. If DIFFSERV is enabled, the full table should be initialized by the host.
BITS
DESCRIPTION
TYPE
DEFAULT
31:3
RESERVED
RO
-
2:0
DIFFSERV Priority
These bits specify the assigned receive priority for IP packets with a ToS/CS
field that matches this index.
R/W
000b
SMSC LAN9312
381
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.14
Switch Engine DIFFSERV Table Read Data Register (SWE_DIFFSERV_TBL_RD_DATA)
Register #:
1813h
Size:
32 bits
This register is used to read the DIFFSERV table.
BITS
DESCRIPTION
TYPE
DEFAULT
31:3
RESERVED
RO
-
2:0
DIFFSERV Priority
These bits specify the assigned receive priority for IP packets with a ToS/CS
field that matches this index.
RO
000b
Revision 2.0 (02-14-13)
382
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.15
Switch Engine DIFFSERV Table Command Status Register (SWE_DIFFSERV_TBL_CMD_STS)
Register #:
1814h
Size:
32 bits
This register indicates the current DIFFSERV command status.
BITS
31:1
0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Operation Pending
When set, this bit indicates that the read or write command is taking place.
This bit is cleared once the command has finished.
RO
SC
0b
SMSC LAN9312
383
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.16
Switch Engine Global Ingress Configuration Register (SWE_GLOBAL_INGRSS_CFG)
Register #:
1840h
Size:
32 bits
This register is used to configure the global ingress rules.
BITS
TYPE
DEFAULT
RESERVED
RO
-
Allow Monitorin Echo
When set, monitored packets are allowed to be echoed back to the source
port. When cleared, monitored packets, like other packets, are never sent
back to the source port.
R/W
0b
IGMP Monitoring Port
This field is the port bit map where IPv4 IGMP packets are sent.
R/W
0b
9
Use IP
When set, the IPv4 TOS or IPv6 SC field is enabled as a transmit priority
queue choice.
R/W
0b
8
RESERVED
R/W
0b
7
Enable IGMP Monitoring
When set, IPv4 IGMP packets are monitored and sent to the IGMP
monitoring port.
R/W
0b
6
SWE Counter Test
When this bit is set the Switch Engine counters that normally clear to 0 when
read will be set to 7FFF_FFFCh when read.
R/W
0b
5
DA Highest Priority
When this bit is set and the Static bit in the ALR table for the destination
MAC address is set, the transmit priority queue that is selected is taken from
the ALR Priority bits (see the Switch Engine ALR Read Data 1 Register
(SWE_ALR_RD_DAT_1)).
R/W
0b
4
Filter Multicast
When this bit is set, packets with a multicast destination address are filtered
if the address is not found in the ALR table. Broadcasts are not included in
this filter.
R/W
0b
3
Drop Unknown
When this bit is set, packets with a unicast destination address are filtered
if the address is not found in the ALR table.
R/W
0b
2
Use Precedence
When the priority is taken from an IPV4 packet (enabled via the Use IP bit),
this bit selects between precedence bits in the TOS octet or the DIFFSERV
table.
R/W
1b
31:14
13
DESCRIPTION
This bit is useful when the monitoring port wishes to receive it’s own IGMP
packets.
12:10
When set, IPv4 packets will use the precedence bits in the TOS octet to
select the transmit priority queue. When cleared, IPv4 packets will use the
DIFFSERV table to select the transmit priority queue.
Revision 2.0 (02-14-13)
384
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
1
VL Higher Priority
When this bit is set and VLANs are enabled, the priority from the VLAN tag
has higher priority than the IP TOS/SC field.
R/W
1b
0
VLAN Enable
When set, VLAN ingress rules are enabled. This also enables the VLAN to
be used as the transmit priority queue selection.
R/W
0b
SMSC LAN9312
385
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.17
Switch Engine Port Ingress Configuration Register (SWE_PORT_INGRSS_CFG)
Register #:
1841h
Size:
32 bits
This register is used to configure the per port ingress rules.
BITS
DESCRIPTION
TYPE
DEFAULT
31:6
RESERVED
RO
-
5:3
Enable Learning on Ingress
When set, source addresses are learned when a packet is received on the
corresponding port and the corresponding Port State in the Switch Engine
Port State Register (SWE_PORT_STATE) is set to forwarding or learning.
R/W
111b
R/W
000b
There is one enable bit per ingress port. Bits 5,4,3 correspond to switch
ports 2,1,0 respectively.
2:0
Enable Membership Checking
When set, VLAN membership is checked when a packet is received on the
corresponding port.
The packet will be filtered if the ingress port is not a member of the VLAN
(unless the Admit Non Member bit is set for the port in the Switch Engine
Admit Non Member Register (SWE_ADMT_N_MEMBER))
For destination addresses that are found in the ALR table, the packet will be
filtered if the egress port is not a member of the VLAN (for destination
addresses that are not found in the ALR table only the ingress port is
checked for membership).
The VLAN Enable bit in the Switch Engine Global Ingress Configuration
Register (SWE_GLOBAL_INGRSS_CFG) needs to be set for these bits to
have an affect.
There is one enable bit per ingress port. Bits 2,1,0 correspond to switch
ports 2,1,0 respectively.
Revision 2.0 (02-14-13)
386
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.18
Switch Engine Admit Only VLAN Register (SWE_ADMT_ONLY_VLAN)
Register #:
1842h
Size:
32 bits
This register is used to configure the per port ingress rule for allowing only VLAN tagged packets.
BITS
DESCRIPTION
TYPE
DEFAULT
31:3
RESERVED
RO
-
2:0
Admit Only VLAN
When set, untagged and priority tagged packets are filtered.
R/W
000b
The VLAN Enable bit in the Switch Engine Global Ingress Configuration
Register (SWE_GLOBAL_INGRSS_CFG) needs to be set for these bits to
have an affect.
There is one enable bit per ingress port. Bits 2,1,0 correspond to switch
ports 2,1,0 respectively.
SMSC LAN9312
387
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.19
Switch Engine Port State Register (SWE_PORT_STATE)
Register #:
1843h
Size:
32 bits
This register is used to configure the per port spanning tree state.
BITS
DESCRIPTION
TYPE
DEFAULT
31:6
RESERVED
RO
-
5:4
Port State Port 2
These bits specify the spanning tree port states for Port 2.
R/W
00b
R/W
00b
R/W
00b
00 = Forwarding
01 = Blocking
10 = Learning
11 = Listening
3:2
Port State Port 1
These bits specify the spanning tree port states for Port 1.
00 = Forwarding
01 = Blocking
10 = Learning
11 = Listening
1:0
Port State Port 0
These bits specify the spanning tree port states for Port 0(Host MAC).
00 = Forwarding
01 = Blocking
10 = Learning
11 = Listening
Note:
Typically, the Host MAC is kept in the forwarding state, since it is
not a true network port.
Revision 2.0 (02-14-13)
388
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.20
Switch Engine Priority to Queue Register (SWE_PRI_TO_QUE)
Register #:
1845h
Size:
32 bits
This register specifies the Traffic Class table that maps the packet priority into the egress queues.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:14
Priority 7 traffic Class
These bits specify the egress queue that is used for packets with a priority
of 7.
R/W
11b
13:12
Priority 6 traffic Class
These bits specify the egress queue that is used for packets with a priority
of 6.
R/W
11b
11:10
Priority 5 traffic Class
These bits specify the egress queue that is used for packets with a priority
of 5.
R/W
10b
9:8
Priority 4 traffic Class
These bits specify the egress queue that is used for packets with a priority
of 4.
R/W
10b
7:6
Priority 3 traffic Class
These bits specify the egress queue that is used for packets with a priority
of 3.
R/W
01b
5:4
Priority 2 traffic Class
These bits specify the egress queue that is used for packets with a priority
of 2.
R/W
00b
3:2
Priority 1 traffic Class
These bits specify the egress queue that is used for packets with a priority
of 1.
R/W
00b
1:0
Priority 0 traffic Class
These bits specify the egress queue that is used for packets with a priority
of 0.
R/W
01b
SMSC LAN9312
389
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.21
Switch Engine Port Mirroring Register (SWE_PORT_MIRROR)
Register #:
1846h
Size:
32 bits
This register is used to configure port mirroring.
BITS
31:9
8
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Enable RX Mirroring Filtered
When set, packets that would normally have been filtered are included in the
receive mirroring function and are sent only to the sniffer port. When
cleared, filtered packets are not mirrored.
R/W
0b
R/W
00b
R/W
00b
Note:
7:5
Sniffer Port
These bits specify the sniffer port that transmits packets that are monitored.
Bits 7,6,5 correspond to switch ports 2,1,0 respectively.
Note:
4:2
The Ingress Filtered Count Registers will still count these packets
as filtered and the Switch Engine Interrupt Pending Register
(SWE_IPR) will still register a drop interrupt.
Only one port should be set as the sniffer.
Mirrored Port
These bits specify if a port is to be mirrored. Bits 4,3,2 correspond to switch
ports 2,1,0 respectively.
Note:
Multiple ports can be set as mirrored.
1
Enable RX Mirroring
This bit enables packets received on the mirrored ports to be also sent to
the sniffer port.
R/W
0b
0
Enable TX Mirroring
This bit enables packets transmitted on the mirrored ports to be also sent to
the sniffer port.
R/W
0b
Revision 2.0 (02-14-13)
390
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.22
Switch Engine Ingress Port Type Register (SWE_INGRSS_PORT_TYP)
Register #:
1847h
Size:
32 bits
This register is used to enable the special tagging mode used to determine the destination port based
on the VLAN tag contents.
BITS
DESCRIPTION
TYPE
DEFAULT
31:6
RESERVED
RO
-
5:4
Ingress Port Type Port 2
A setting of 11b enables the usage of the VLAN tag to specify the packet
destination. All other values disable this feature.
R/W
00b
3:2
Ingress Port Type Port 1
A setting of 11b enables the usage of the VLAN tag to specify the packet
destination. All other values disable this feature.
R/W
00b
1:0
Ingress Port Type Port 0
A setting of 11b enables the usage of the VLAN tag to specify the packet
destination. All other values disable this feature.
R/W
00b
SMSC LAN9312
391
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.23
Switch Engine Broadcast Throttling Register (SWE_BCST_THROT)
Register #:
1848h
Size:
32 bits
This register configures the broadcast input rate throttling.
BITS
31:27
26
25:18
17
16:9
8
7:0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Broadcast Throttle Enable Port 2
This bit enables broadcast input rate throttling on Port 2.
R/W
0b
Broadcast Throttle Level Port 2
These bits specify the number of bytes x 64 allowed to be received per
every 1.72mS interval.
R/W
02h
Broadcast Throttle Enable Port 1
This bit enables broadcast input rate throttling on Port 1.
R/W
0b
Broadcast Throttle Level Port 1
These bits specify the number of bytes x 64 allowed to be received per
every 1.72mS interval.
R/W
02h
Broadcast Throttle Enable Port 0
This bit enables broadcast input rate throttling on Port 0(Host MAC).
R/W
0b
Broadcast Throttle Level Port 0
These bits specify the number of bytes x 64 allowed to be received per
every 1.72mS interval.
R/W
02h
Revision 2.0 (02-14-13)
392
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.24
Switch Engine Admit Non Member Register (SWE_ADMT_N_MEMBER)
Register #:
1849h
Size:
32 bits
This register is used to allow access to a VLAN even if the ingress port is not a member.
BITS
DESCRIPTION
TYPE
DEFAULT
31:3
RESERVED
RO
-
2:0
Admit Non Member
When set, a received packet is accepted even if the ingress port is not a
member of the destination VLAN. The VLAN still must be active in the
switch.
R/W
000b
There is one bit per ingress port. Bits 2,1,0 correspond to switch ports 2,1,0
respectively.
SMSC LAN9312
393
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.25
Switch Engine Ingress Rate Configuration Register (SWE_INGRSS_RATE_CFG)
Register #:
184Ah
Size:
32 bits
This register, along with the settings accessible via the Switch Engine Ingress Rate Command Register
(SWE_INGRSS_RATE_CMD), is used to configure the ingress rate metering/coloring.
BITS
DESCRIPTION
TYPE
DEFAULT
31:3
RESERVED
RO
-
2:1
Rate Mode
These bits configure the rate metering/coloring mode.
R/W
00b
R/W
0b
00 = Source Port & Priority
01 = Source Port Only
10 = Priority Only
11 = RESERVED
0
Ingress Rate Enable
When set, ingress rates are metered and packets are colored and dropped
if necessary.
Revision 2.0 (02-14-13)
394
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.26
Switch Engine Ingress Rate Command Register (SWE_INGRSS_RATE_CMD)
Register #:
184Bh
Size:
32 bits
This register is used to indirectly read and write the ingress rate metering/color table registers. A write
to this address performs the specified access.
For a read access, the Operation Pending bit in the Switch Engine Ingress Rate Command Status
Register (SWE_INGRSS_RATE_CMD_STS) indicates when the command is finished. The Switch
Engine Ingress Rate Read Data Register (SWE_INGRSS_RATE_RD_DATA) can then be read.
For a write access, the Switch Engine Ingress Rate Write Data Register
(SWE_INGRSS_RATE_WR_DATA) should be written first. The Operation Pending bit in the Switch
Engine Ingress Rate Command Status Register (SWE_INGRSS_RATE_CMD_STS) indicates when the
command is finished.
For details on 16-bit wide Ingress Rate Table registers indirectly accessible by this register, see
Section 14.5.3.26.1 below.
BITS
31:8
7
6:5
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Ingress Rate RnW
These bits specify a read(1) or write(0) command.
R/W
0b
Type
These bits select between the ingress rate metering/color table registers as
follows:
R/W
00b
R/W
0h
00 = RESERVED
01 = Committed Information Rate Registers
10 = Committed Burst Register
11 = Excess Burst Register
4:0
(uses CIS Address field)
CIR Address
These bits select one of the 24 Committed Information Rate registers.
When Rate Mode is set to Source Port & Priority in the Switch Engine
Ingress Rate Configuration Register (SWE_INGRSS_RATE_CFG), the first
set of 8 registers (CIR addresses 0-7) are for to Port 0, the second set of 8
registers (CIR addresses 8-15) are for Port 1, and the third set of registers
(CIR addresses 16-23) are for Port 2. Priority 0 is the lower register of each
set (e.g. 0, 8, and 16).
When Rate Mode is set to Source Port Only, the first register (CIR address
0) is for Port 0, the second register (CIR address 1) is for Port 1, and the
third register (CIR address 2) is for Port 2.
When Rate Mode is set to Priority Only, the first register (CIR address 0) is
for priority 0, the second register (CIR address 1) is for priority 1, and so
forth up to priority 23.
Note:
SMSC LAN9312
Values outside of the valid range may cause unexpected results.
395
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.26.1
INGRESS RATE TABLE REGISTERS
The ingress rate metering/color table consists of 24 Committed Information Rate (CIR) registers (one
per port/priority), a Committed Burst Size register, and an Excess Burst Size register. All metering/color
table registers are 16-bits in size and are accessed indirectly via the Switch Engine Ingress Rate
Command Register (SWE_INGRSS_RATE_CMD). Descriptions of these registers are detailed in
Table 14.13 below.
Table 14.13 Metering/Color Table Register Descriptions
DESCRIPTION
TYPE
DEFAULT
Excess Burst Size
This register specifies the maximum excess burst size in bytes. Bursts larger than
this value that exceed the excess data rate are dropped.
R/W
0600h
R/W
0600h
R/W
0014h
Note:
Either this value or the Committed Burst Size should be set larger than or
equal to the largest possible packet expected.
Note:
All of the Excess Burst token buckets are initialized to this default value.
If a lower value is programmed into this register, the token buckets will
need to be normally depleted below this value before this value has any
affect on limiting the token bucket maximum values.
This register is 16-bits wide.
Committed Burst Size
This register specifies the maximum committed burst size in bytes. Bursts larger
than this value that exceed the committed data rate are subjected to random
dropping.
Note:
Either this value or the Excess Burst Size should be set larger than or
equal to the largest possible packet expected.
Note:
All of the Committed Burst token buckets are initialized to this default
value. If a lower value is programmed into this register, the token buckets
will need to be normally depleted below this value before this value has
any affect on limiting the token bucket maximum values.
This register is 16-bits wide.
Committed Information Rate (CIR)
These registers specify the committed data rate for the port/priority pair. The rate
is specified in time per byte. The time is this value plus 1 times 20nS.
There are 24 of these registers each 16-bits wide.
Revision 2.0 (02-14-13)
396
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.27
Switch Engine Ingress Rate Command Status Register (SWE_INGRSS_RATE_CMD_STS)
Register #:
184Ch
Size:
32 bits
This register indicates the current ingress rate command status.
BITS
31:1
0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Operation Pending
When set, indicates that the read or write command is taking place. This bit
is cleared once the command has finished.
RO
SC
0b
SMSC LAN9312
397
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.28
Switch Engine Ingress Rate Write Data Register (SWE_INGRSS_RATE_WR_DATA)
Register #:
184Dh
Size:
32 bits
This register is used to write the ingress rate table registers.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:0
Data
This is the data to be written to the ingress rate table registers as specified
in the Switch Engine Ingress Rate Command Register
(SWE_INGRSS_RATE_CMD). Refer to Section 14.5.3.26.1, "Ingress Rate
Table Registers," on page 396 for details on these registers.
R/W
0000h
Revision 2.0 (02-14-13)
398
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.29
Switch Engine Ingress Rate Read Data Register (SWE_INGRSS_RATE_RD_DATA)
Register #:
184Eh
Size:
32 bits
This register is used to read the ingress rate table registers.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:0
Data
This is the read data from the ingress rate table registers as specified in the
Switch Engine Ingress Rate Command Register
(SWE_INGRSS_RATE_CMD). Refer to Section 14.5.3.26.1, "Ingress Rate
Table Registers," on page 396 for details on these registers.
RO
0000h
SMSC LAN9312
399
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.30
Switch Engine Port 0 Ingress Filtered Count Register (SWE_FILTERED_CNT_MII)
Register #:
1850h
Size:
32 bits
This register counts the number of packets filtered at ingress on Port 0(Host MAC). This count includes
packets filtered due to broadcast throttling but does not include packets dropped due to ingress rate
limiting (which are counted separately).
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Filtered
This field is a count of packets filtered at ingress and is cleared when read.
RC
00000000h
Note:
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Revision 2.0 (02-14-13)
400
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.31
Switch Engine Port 1 Ingress Filtered Count Register (SWE_FILTERED_CNT_1)
Register #:
1851h
Size:
32 bits
This register counts the number of packets filtered at ingress on Port 1. This count includes packets
filtered due to broadcast throttling but does not include packets dropped due to ingress rate limiting
(which are counted separately).
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Filtered
This field is a count of packets filtered at ingress and is cleared when read.
RC
00000000h
Note:
SMSC LAN9312
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
401
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.32
Switch Engine Port 2 Ingress Filtered Count Register (SWE_FILTERED_CNT_2)
Register #:
1852h
Size:
32 bits
This register counts the number of packets filtered at ingress on Port 2. This count includes packets
filtered due to broadcast throttling but does not include packets dropped due to ingress rate limiting
(which are counted separately).
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Filtered
This field is a count of packets filtered at ingress and is cleared when read.
RC
00000000h
Note:
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Revision 2.0 (02-14-13)
402
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.33
Switch Engine Port 0 Ingress VLAN Priority Regeneration Table Register
(SWE_INGRSS_REGEN_TBL_MII)
Register #:
1855h
Size:
32 bits
This register provides the ability to map the received VLAN priority to a regenerated priority. The
regenerated priority is used in determining the output priority queue. By default, the regenerated priority
is identical to the received priority.
BITS
DESCRIPTION
TYPE
DEFAULT
31:24
RESERVED
RO
-
23:21
Regen7
These bits specify the regenerated priority for received priority 7.
R/W
7h
20:18
Regen6
These bits specify the regenerated priority for received priority 6.
R/W
6h
17:15
Regen5
These bits specify the regenerated priority for received priority 5.
R/W
5h
14:12
Regen4
These bits specify the regenerated priority for received priority 4.
R/W
4h
11:9
Regen3
These bits specify the regenerated priority for received priority 3.
R/W
3h
8:6
Regen2
These bits specify the regenerated priority for received priority 2.
R/W
2h
5:3
Regen1
These bits specify the regenerated priority for received priority 1.
R/W
1h
2:0
Regen0
These bits specify the regenerated priority for received priority 0.
R/W
0h
SMSC LAN9312
403
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.34
Switch Engine Port 1 Ingress VLAN Priority Regeneration Table Register
(SWE_INGRSS_REGEN_TBL_1)
Register #:
1856h
Size:
32 bits
This register provides the ability to map the received VLAN priority to a regenerated priority. The
regenerated priority is used in determining the output priority queue. By default, the regenerated priority
is identical to the received priority.
BITS
DESCRIPTION
TYPE
DEFAULT
31:24
RESERVED
RO
-
23:21
Regen7
These bits specify the regenerated priority for received priority 7.
R/W
7h
20:18
Regen6
These bits specify the regenerated priority for received priority 6.
R/W
6h
17:15
Regen5
These bits specify the regenerated priority for received priority 5.
R/W
5h
14:12
Regen4
These bits specify the regenerated priority for received priority 4.
R/W
4h
11:9
Regen3
These bits specify the regenerated priority for received priority 3.
R/W
3h
8:6
Regen2
These bits specify the regenerated priority for received priority 2.
R/W
2h
5:3
Regen1
These bits specify the regenerated priority for received priority 1.
R/W
1h
2:0
Regen0
These bits specify the regenerated priority for received priority 0.
R/W
0h
Revision 2.0 (02-14-13)
404
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.35
Switch Engine Port 2 Ingress VLAN Priority Regeneration Table Register
(SWE_INGRSS_REGEN_TBL_2)
Register #:
1857h
Size:
32 bits
This register provides the ability to map the received VLAN priority to a regenerated priority. The
regenerated priority is used in determining the output priority queue. By default, the regenerated priority
is identical to the received priority.
BITS
DESCRIPTION
TYPE
DEFAULT
31:24
RESERVED
RO
-
23:21
Regen7
These bits specify the regenerated priority for received priority 7.
R/W
7h
20:18
Regen6
These bits specify the regenerated priority for received priority 6.
R/W
6h
17:15
Regen5
These bits specify the regenerated priority for received priority 5.
R/W
5h
14:12
Regen4
These bits specify the regenerated priority for received priority 4.
R/W
4h
11:9
Regen3
These bits specify the regenerated priority for received priority 3.
R/W
3h
8:6
Regen2
These bits specify the regenerated priority for received priority 2.
R/W
2h
5:3
Regen1
These bits specify the regenerated priority for received priority 1.
R/W
1h
2:0
Regen0
These bits specify the regenerated priority for received priority 0.
R/W
0h
SMSC LAN9312
405
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.36
Switch Engine Port 0 Learn Discard Count Register (SWE_LRN_DISCRD_CNT_MII)
Register #:
1858h
Size:
32 bits
This register counts the number of MAC addresses on Port 0(Host MAC) that were not learned or were
overwritten by a different address due to address table space limitations.
BITS
31:0
DESCRIPTION
Learn Discard
This field is a count of MAC addresses not learned or overwritten and is
cleared when read.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Revision 2.0 (02-14-13)
406
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.37
Switch Engine Port 1 Learn Discard Count Register (SWE_LRN_DISCRD_CNT_1)
Register #:
1859h
Size:
32 bits
This register counts the number of MAC addresses on Port 1 that were not learned or were overwritten
by a different address due to address table space limitations.
BITS
31:0
DESCRIPTION
Learn Discard
This field is a count of MAC addresses not learned or overwritten and is
cleared when read.
Note:
SMSC LAN9312
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
407
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.38
Switch Engine Port 2 Learn Discard Count Register (SWE_LRN_DISCRD_CNT_2)
Register #:
185Ah
Size:
32 bits
This register counts the number of MAC addresses on Port 2 that were not learned or were overwritten
by a different address due to address table space limitations.
BITS
31:0
DESCRIPTION
Learn Discard
This field is a count of MAC addresses not learned or overwritten and is
cleared when read.
Note:
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Revision 2.0 (02-14-13)
408
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.39
Switch Engine Interrupt Mask Register (SWE_IMR)
Register #:
1880h
Size:
32 bits
This register contains the Switch Engine interrupt mask, which masks the interrupts in the Switch
Engine Interrupt Pending Register (SWE_IPR). All Switch Engine interrupts are masked by setting the
Interrupt Mask bit. Clearing this bit will unmask the interrupts. Refer to Chapter 5, "System Interrupts,"
on page 49 for more information.
BITS
31:1
0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Interrupt Mask
When set, this bit masks interrupts from the Switch Engine. The status bits
in the Switch Engine Interrupt Pending Register (SWE_IPR) are not
affected.
R/W
1b
SMSC LAN9312
409
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.3.40
Switch Engine Interrupt Pending Register (SWE_IPR)
Register #:
1881h
Size:
32 bits
This register contains the Switch Engine interrupt status. The status is double buffered. All interrupts
in this register may be masked via the Switch Engine Interrupt Mask Register (SWE_IMR) register.
Refer to Chapter 5, "System Interrupts," on page 49 for more information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:15
RESERVED
RO
-
14:11
Drop Reason B
When bit 8 is set, these bits indicate the reason a packet was dropped per
the table below:
RC
0h
BIT
VALUES
DESCRIPTION
0000
Admit Only VLAN was set and the packet was untagged or priority tagged.
0001
The destination address was not in the ALR table (unknown or broadcast),
Enable Membership Checking on ingress was set, Admit Non Member was
cleared and the source port was not a member of the incoming VLAN.
0010
The destination address was found in the ALR table but the source port was
not in the forwarding state.
0011
The destination address was found in the ALR table but the destination port
was not in the forwarding state.
0100
The destination address was found in the ALR table but Enable Membership
Checking on ingress was set and the destination port was not a member of the
incoming VLAN.
0101
The destination address was found in the ALR table but the Enable
Membership Checking on ingress was set, Admit Non Member was cleared and
the source port was not a member of the incoming VLAN.
0110
Drop Unknown was set and the destination address was a unicast but not in
the ALR table.
0111
Filter Multicast was set and the destination address was a multicast and not in
the ALR table.
1000
The packet was a broadcast but exceeded the Broadcast Throttling limit.
1001
The destination address was not in the ALR table (unknown or broadcast) and
the source port was not in the forwarding state.
1010
The destination address was found in the ALR table but the source and
destination ports were the same.
1011
The destination address was found in the ALR table and the Filter bit was set
for that address.
1100
RESERVED
1101
RESERVED
1110
A packet was received with a VLAN ID of FFFh
1111
RESERVED
Revision 2.0 (02-14-13)
410
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
TYPE
DEFAULT
RC
00b
Set B Valid
When set, bits 14:9 are valid.
RC
0b
7:4
Drop Reason A
When bit 1 is set, these bits indicate the reason a packet was dropped. See
the Drop Reason B description above for definitions of each value of this
field.
RC
0h
3:2
Source port A
When bit 1 is set, these bits indicate the source port on which the packet
was dropped.
RC
00b
10:9
DESCRIPTION
Source Port B
When bit 8 is set, these bits indicate the source port on which the packet
was dropped.
00 = Port 0
01 = Port 1
10 = Port 2
11 = RESERVED
8
00 = Port 0
01 = Port 1
10 = Port 2
11 = RESERVED
1
Set A Valid
When set, bits 7:2 are valid.
RC
0b
0
Interrupt Pending
When set, a packet dropped event(s) is indicated.
RC
0b
SMSC LAN9312
411
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4
Buffer Manager CSRs
This section details the Buffer Manager (BM) registers. These registers allow configuration and
monitoring of the switch buffer levels and usage. A list of the general switch CSRs and their
corresponding register numbers is included in Table 14.12.
14.5.4.1
Buffer Manager Configuration Register (BM_CFG)
Register #:
1C00h
Size:
32 bits
This register enables egress rate pacing and ingress rate discarding.
BITS
TYPE
DEFAULT
RESERVED
RO
-
6
BM Counter Test
When this bit is set, Buffer Manager (BM) counters that normally clear to 0
when read, will be set to 7FFF_FFFC when read.
R/W
0b
5
Fixed Priority Queue Servicing
When set, output queues are serviced with a fixed priority ordering. When
cleared, output queues are serviced with a weighted round robin ordering.
R/W
0b
4:2
Egress Rate Enable
When set, egress rate pacing is enabled. Bits 4,3,2 correspond to switch
ports 2,1,0 respectively.
R/W
0b
Drop on Yellow
When this bit is set, packets that exceed the Ingress Committed Burst Size
(colored Yellow) are subjected to random discard.
R/W
0b
R/W
0b
31:7
1
DESCRIPTION
Note:
0
See Section 14.5.3.26, "Switch Engine Ingress Rate Command
Register (SWE_INGRSS_RATE_CMD)," on page 395 for
information on configuring the Ingress Committed Burst Size.
Drop on Red
When this bit is set, packets that exceed the Ingress Excess Burst Size
(colored Red) are discarded.
Note:
See Section 14.5.3.26, "Switch Engine Ingress Rate Command
Register (SWE_INGRSS_RATE_CMD)," on page 395 for
information on configuring the Ingress Excess Burst Size.
Revision 2.0 (02-14-13)
412
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.2
Buffer Manager Drop Level Register (BM_DROP_LVL)
Register #:
1C01h
Size:
32 bits
This register configures the overall buffer usage limits.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:8
Drop Level Low
These bits specify the buffer limit that can be used per ingress port during
times when 2 or 3 ports are active.
R/W
49h
R/W
64h
Each buffer is 128 bytes.
Note:
7:0
A port is “active” when 36 buffers are in use for that port.
Drop Level High
These bits specify the buffer limit that can be used per ingress port during
times when 1 port is active.
Each buffer is 128 bytes.
Note:
SMSC LAN9312
A port is “active” when 36 buffers are in use for that port.
413
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.3
Buffer Manager Flow Control Pause Level Register (BM_FC_PAUSE_LVL)
Register #:
1C02h
Size:
32 bits
This register configures the buffer usage level when a Pause frame or backpressure is sent.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:8
Pause Level Low
These bits specify the buffer usage level during times when 2 or 3 ports are
active.
R/W
21h
R/W
3Ch
Each buffer is 128 bytes.
Note:
7:0
A port is “active” when 36 buffers are in use for that port.
Pause Level High
These bits specify the buffer usage level during times when 1 port is active.
Each buffer is 128 bytes.
Note:
A port is “active” when 36 buffers are in use for that port.
Revision 2.0 (02-14-13)
414
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.4
Buffer Manager Flow Control Resume Level Register (BM_FC_RESUME_LVL)
Register #:
1C03h
Size:
32 bits
This register configures the buffer usage level when a Pause frame with a pause value of 1 is sent.
BITS
DESCRIPTION
TYPE
DEFAULT
31:16
RESERVED
RO
-
15:8
Resume Level Low
These bits specify the buffer usage level during times when 2 or 3 ports are
active.
R/W
03h
R/W
07h
Each buffer is 128 bytes.
Note:
7:0
A port is “active” when 36 buffers are in use for that port.
Resume Level High
These bits specify the buffer usage level during times when 0 or 1 ports are
active.
Each buffer is 128 bytes.
Note:
SMSC LAN9312
A port is “active” when 36 buffers are in use for that port.
415
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.5
Buffer Manager Broadcast Buffer Level Register (BM_BCST_LVL)
Register #:
1C04h
Size:
32 bits
This register configures the buffer usage limits for broadcasts, multicasts, and unknown unicasts.
BITS
DESCRIPTION
TYPE
DEFAULT
31:8
RESERVED
RO
-
7:0
Broadcast Drop Level
These bits specify the maximum number of buffers that can be used by
broadcasts, multicasts, and unknown unicasts.
R/W
31h
Each buffer is 128 bytes.
Revision 2.0 (02-14-13)
416
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.6
Buffer Manager Port 0 Drop Count Register (BM_DRP_CNT_SRC_MII)
Register #:
1C05h
Size:
32 bits
This register counts the number of packets dropped by the Buffer Manager that were received on Port
0(Host MAC). This count includes packets dropped due to buffer space limits and ingress rate limit
discarding (Red and random Yellow dropping).
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Dropped Count
These bits count the number of dropped packets received on Port 0 and is
cleared when read.
RC
00000000h
Note:
SMSC LAN9312
The counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
417
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.7
Buffer Manager Port 1 Drop Count Register (BM_DRP_CNT_SRC_1)
Register #:
1C06h
Size:
32 bits
This register counts the number of packets dropped by the Buffer Manager that were received on Port
1. This count includes packets dropped due to buffer space limits and ingress rate limit discarding (Red
and random Yellow dropping).
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Dropped Count
These bits count the number of dropped packets received on Port 1 and is
cleared when read.
RC
00000000h
Note:
The counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Revision 2.0 (02-14-13)
418
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.8
Buffer Manager Port 2 Drop Count Register (BM_DRP_CNT_SRC_2)
Register #:
1C07h
Size:
32 bits
This register counts the number of packets dropped by the Buffer Manager that were received on Port
2. This count includes packets dropped due to buffer space limits and ingress rate limit discarding (Red
and random Yellow dropping).
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Dropped Count
These bits count the number of dropped packets received on Port 2 and is
cleared when read.
RC
00000000h
Note:
SMSC LAN9312
The counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
419
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.9
Buffer Manager Reset Status Register (BM_RST_STS)
Register #:
1C08h
Size:
32 bits
This register indicates when the Buffer Manager has been initialized by the reset process.
BITS
31:1
0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
BM Ready
When set, indicates the Buffer Manager tables have finished being initialized
by the reset process. The initialization is performed upon any reset that
resets the switch fabric.
RO
SS
Note 14.63
Note 14.63 The default value of this bit is 0 immediately following any switch fabric reset and then selfsets to 1 once the ALR table is initialized.
Revision 2.0 (02-14-13)
420
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.10
Buffer Manager Random Discard Table Command Register (BM_RNDM_DSCRD_TBL_CMD)
Register #:
1C09h
Size:
32 bits
This register is used to read and write the Random Discard Weight table. A write to this address
performs the specified access. This table is used to set the packet drop probability verses the buffer
usage.
For a read access, the Buffer Manager Random Discard Table Read Data Register
(BM_RNDM_DSCRD_TBL_RDATA) can be read following a write to this register.
For a write access, the Buffer Manager Random Discard Table Write Data Register
(BM_RNDM_DSCRD_TBL_WDATA) should be written before writing this register.
BITS
31:5
4
3:0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Random Discard Weight Table RnW
Specifies a read (1) or a write (0) command.
R/W
0b
Random Discard Weight Table Index
Specifies the buffer usage range that is accessed.
R/W
0h
There are a total of 16 probability entries. Each entry corresponds to a range
of the number of buffers used by the ingress port. The ranges are structured
to give more resolution towards the lower buffer usage end.
SMSC LAN9312
BIT
VALUES
BUFFER USAGE LEVEL
0000
0 to 7
0001
8 to 15
0010
16 to 23
0011
24 to 31
0100
32 to 39
0101
40 to 47
0110
48 to 55
0111
56 to 63
1000
64 to 79
1001
80 to 95
1010
96 to 111
1011
112 to 127
1100
128 to 159
1101
160 to 191
1110
192 to 223
1111
224 to 255
421
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.11
Buffer Manager Random Discard Table Write Data Register (BM_RNDM_DSCRD_TBL_WDATA)
Register #:
1C0Ah
Size:
32 bits
This register is used to write the Random Discard Weight table.
Note: The Random Discard Weight table is not initialized upon reset or power-up. If a random discard
is enabled, the full table should be initialized by the host.
BITS
31:10
9:0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Drop Probability
These bits specify the discard probability of a packet that has been colored
Yellow by the ingress metering. The probability is given in 1/1024’s. For
example, a setting of 1 is one in 1024, or approximately 0.1%. A setting of
all ones (1023) is 1023 in 1024, or approximately 99.9%.
R/W
000h
There are a total of 16 probability entries. Each entry corresponds to a range
of the number of buffers used by the ingress port, as specified in Section
14.5.4.10, "Buffer Manager Random Discard Table Command Register
(BM_RNDM_DSCRD_TBL_CMD)".
Revision 2.0 (02-14-13)
422
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.12
Buffer Manager Random Discard Table Read Data Register (BM_RNDM_DSCRD_TBL_RDATA)
Register #:
1C0Bh
Size:
32 bits
This register is used to read the Random Discard Weight table.
BITS
31:10
9:0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Drop Probability
These bits specify the discard probability of a packet that has been colored
Yellow by the ingress metering. The probability is given in 1/1024’s. For
example, a setting of 1 is one in 1024, or approximately 0.1%. A setting of
all ones (1023) is 1023 in 1024, or approximately 99.9%.
RO
000h
There are a total of 16 probability entries. Each entry corresponds to a range
of the number of buffers used by the ingress port, as specified in Section
14.5.4.10, "Buffer Manager Random Discard Table Command Register
(BM_RNDM_DSCRD_TBL_CMD)".
SMSC LAN9312
423
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.13
Buffer Manager Egress Port Type Register (BM_EGRSS_PORT_TYPE)
Register #:
1C0Ch
Size:
32 bits
This register is used to configure the egress VLAN tagging rules. See Section 6.5.6, "Adding,
Removing, and Changing VLAN Tags," on page 79 for additional details.
BITS
31:22
21
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Insert Tag Port 2
When set, untagged packets will have a tag added that contains the Default
VLAN ID and Priority of the ingress port.
R/W
0b
R/W
0b
R/W
0b
R/W
0b
The un-tag bit in the VLAN table for the default VLAN ID also needs to be
cleared in order for the tag to be inserted.
This is only used when the Egress Port Type is set as Hybrid.
20
Change VLAN ID Port 2
When set, regular tagged packets will have their VLAN ID overwritten with
the Default VLAN ID of the egress port.
The Change Tag bit also needs to be set.
The un-tag bit in the VLAN table for the incoming VLAN ID also needs to be
cleared, otherwise the tag will be removed instead.
Priority tagged packets will have VLAN ID overwritten with the Default VLAN
ID of the ingress port independent of this bit.
This is only used when the Egress Port Type is set as Hybrid.
19
Change Priority Port 2
When set, regular tagged packets will have their Priority overwritten with the
Default Priority of the egress port. Priority tagged packets will have VLAN ID
overwritten with the Default VLAN ID of the ingress port.
For regular tagged packets, the Change Tag bit also needs to be set.
The un-tag bit in the VLAN table for the incoming VLAN ID also needs to be
cleared, otherwise the tag would be removed instead.
This is only used when the Egress Port Type is set as Hybrid.
18
Change Tag Port 2
When set, allows the Change Tag and Change Priority bits to affect regular
tagged packets.
This bit has no affect on priority tagged packets.
This is only used when the Egress Port Type is set as Hybrid.
Revision 2.0 (02-14-13)
424
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
17:16
Egress Port Type Port 2
These bits set the egress port type which determines the tagging/un-tagging
rules.
R/W
0b
RESERVED
RO
-
13
Insert Tag Port 1
Identical to Insert Tag Port 2 definition above.
R/W
0b
12
Change VLAN ID Port 1
Identical to Change VLAN ID Port 2 definition above.
R/W
0b
11
Change Priority Port 1
Identical to Change Priority Port 2 definition above.
R/W
0b
10
Change Tag Port 1
Identical to Change Tag Port 2 definition above.
R/W
0b
9:8
Egress Port Type Port 1
Identical to Egress Port Type Port 2 definition above.
R/W
0b
7:6
RESERVED
RO
-
5
Insert Tag Port 0(Host MAC)
Identical to Insert Tag Port 2 definition above.
R/W
0b
4
Change VLAN ID Port 0(Host MAC)
Identical to Change VLAN ID Port 2 definition above.
R/W
0b
3
Change Priority Port 0(Host MAC)
Identical to Change Priority Port 2 definition above.
R/W
0b
2
Change Tag Port 0(Host MAC)
Identical to Change Tag Port 2 definition above.
R/W
0b
Egress Port Type Port 0(Host MAC)
Identical to Egress Port Type Port 2 definition above.
R/W
0b
BIT
VALUES
15:14
1:0
SMSC LAN9312
EGRESS PORT TYPE
00
Dumb
Packets from regular ports pass untouched. Special tagged packets from the
Host MAC port have their tagged stripped.
01
Access
Tagged packets (including special tagged packets from the Host MAC port)
have their tagged stripped.
10
Hybrid
Supports a mix of tagging, un-tagging and changing tags. See Section 6.5.6,
"Adding, Removing, and Changing VLAN Tags," on page 79 for additional
details.
11
CPU
A special tag is added to indicate the source of the packet. See Section 6.5.6,
"Adding, Removing, and Changing VLAN Tags," on page 79 for additional
details.
425
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.14
Buffer Manager Port 0 Egress Rate Priority Queue 0/1 Register (BM_EGRSS_RATE_00_01)
Register #:
1C0Dh
Size:
32 bits
This register, along with the Buffer Manager Configuration Register (BM_CFG), is used to configure
the egress rate pacing.
BITS
DESCRIPTION
TYPE
DEFAULT
31:26
RESERVED
RO
-
25:13
Egress Rate Port 0 Priority Queue 1
These bits specify the egress data rate for the Port 0(Host MAC) priority
queue 1. The rate is specified in time per byte. The time is this value plus
1 times 20nS.
R/W
00000h
12:0
Egress Rate Port 0 Priority Queue 0
These bits specify the egress data rate for the Port 0(Host MAC) priority
queue 0. The rate is specified in time per byte. The time is this value plus
1 times 20nS.
R/W
00000h
Revision 2.0 (02-14-13)
426
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.15
Buffer Manager Port 0 Egress Rate Priority Queue 2/3 Register (BM_EGRSS_RATE_02_03)
Register #:
1C0Eh
Size:
32 bits
This register, along with the Buffer Manager Configuration Register (BM_CFG), is used to configure
the egress rate pacing.
BITS
DESCRIPTION
TYPE
DEFAULT
31:26
RESERVED
RO
-
25:13
Egress Rate Port 0 Priority Queue 3
These bits specify the egress data rate for the Port 0(Host MAC) priority
queue 3. The rate is specified in time per byte. The time is this value plus
1 times 20nS.
R/W
00000h
12:0
Egress Rate Port 0 Priority Queue 2
These bits specify the egress data rate for the Port 0(Host MAC) priority
queue 2. The rate is specified in time per byte. The time is this value plus
1 times 20nS.
R/W
00000h
SMSC LAN9312
427
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.16
Buffer Manager Port 1 Egress Rate Priority Queue 0/1 Register (BM_EGRSS_RATE_10_11)
Register #:
1C0Fh
Size:
32 bits
This register, along with the Buffer Manager Configuration Register (BM_CFG), is used to configure
the egress rate pacing.
BITS
DESCRIPTION
TYPE
DEFAULT
31:26
RESERVED
RO
-
25:13
Egress Rate Port 1 Priority Queue 1
These bits specify the egress data rate for the Port 1 priority queue 1. The
rate is specified in time per byte. The time is this value plus 1 times 20nS.
R/W
00000h
12:0
Egress Rate Port 1 Priority Queue 0
These bits specify the egress data rate for the Port 1 priority queue 0. The
rate is specified in time per byte. The time is this value plus 1 times 20nS.
R/W
00000h
Revision 2.0 (02-14-13)
428
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.17
Buffer Manager Port 1 Egress Rate Priority Queue 2/3 Register (BM_EGRSS_RATE_12_13)
Register #:
1C10h
Size:
32 bits
This register, along with the Buffer Manager Configuration Register (BM_CFG), is used to configure
the egress rate pacing.
BITS
DESCRIPTION
TYPE
DEFAULT
31:26
RESERVED
RO
-
25:13
Egress Rate Port 1 Priority Queue 3
These bits specify the egress data rate for the Port 1 priority queue 3. The
rate is specified in time per byte. The time is this value plus 1 times 20nS.
R/W
00000h
12:0
Egress Rate Port 1 Priority Queue 2
These bits specify the egress data rate for the Port 1 priority queue 2. The
rate is specified in time per byte. The time is this value plus 1 times 20nS.
R/W
00000h
SMSC LAN9312
429
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.18
Buffer Manager Port 2 Egress Rate Priority Queue 0/1 Register (BM_EGRSS_RATE_20_21)
Register #:
1C11h
Size:
32 bits
This register, along with the Buffer Manager Configuration Register (BM_CFG), is used to configure
the egress rate pacing.
BITS
DESCRIPTION
TYPE
DEFAULT
31:26
RESERVED
RO
-
25:13
Egress Rate Port 2 Priority Queue 1
These bits specify the egress data rate for the Port 2 priority queue 1. The
rate is specified in time per byte. The time is this value plus 1 times 20nS.
R/W
00000h
12:0
Egress Rate Port 2 Priority Queue 0
These bits specify the egress data rate for the Port 2 priority queue 0. The
rate is specified in time per byte. The time is this value plus 1 times 20nS.
R/W
00000h
Revision 2.0 (02-14-13)
430
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.19
Buffer Manager Port 2 Egress Rate Priority Queue 2/3 Register (BM_EGRSS_RATE_22_23)
Register #:
1C12h
Size:
32 bits
This register, along with the Buffer Manager Configuration Register (BM_CFG), is used to configure
the egress rate pacing.
BITS
DESCRIPTION
TYPE
DEFAULT
31:26
RESERVED
RO
-
25:13
Egress Rate Port 2 Priority Queue 3
These bits specify the egress data rate for the Port 2 priority queue 3. The
rate is specified in time per byte. The time is this value plus 1 times 20nS.
R/W
00000h
12:0
Egress Rate Port 2 Priority Queue 2
These bits specify the egress data rate for the Port 2 priority queue 2. The
rate is specified in time per byte. The time is this value plus 1 times 20nS.
R/W
00000h
SMSC LAN9312
431
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.20
Buffer Manager Port 0 Default VLAN ID and Priority Register (BM_VLAN_MII)
Register #:
1C13h
Size:
32 bits
This register is used to specify the default VLAN ID and priority of Port 0(Host MAC).
BITS
DESCRIPTION
TYPE
DEFAULT
31:15
RESERVED
RO
-
14:12
Default Priority
These bits specify the default priority that is used when a tag is inserted or
changed on egress.
R/W
000b
11:0
Default VLAN ID
These bits specify the default that is used when a tag is inserted or changed
on egress.
R/W
000h
Revision 2.0 (02-14-13)
432
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.21
Buffer Manager Port 1 Default VLAN ID and Priority Register (BM_VLAN_1)
Register #:
1C14h
Size:
32 bits
This register is used to specify the default VLAN ID and priority of Port 1.
BITS
DESCRIPTION
TYPE
DEFAULT
31:15
RESERVED
RO
-
14:12
Default Priority
These bits specify the default priority that is used when a tag is inserted or
changed on egress.
R/W
000b
11:0
Default VLAN ID
These bits specify the default that is used when a tag is inserted or changed
on egress.
R/W
000h
SMSC LAN9312
433
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.22
Buffer Manager Port 2 Default VLAN ID and Priority Register (BM_VLAN_2)
Register #:
1C15h
Size:
32 bits
This register is used to specify the default VLAN ID and priority of Port 2.
BITS
DESCRIPTION
TYPE
DEFAULT
31:15
RESERVED
RO
-
14:12
Default Priority
These bits specify the default priority that is used when a tag is inserted or
changed on egress.
R/W
000b
11:0
Default VLAN ID
These bits specify the default that is used when a tag is inserted or changed
on egress.
R/W
000h
Revision 2.0 (02-14-13)
434
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.23
Buffer Manager Port 0 Ingress Rate Drop Count Register (BM_RATE_DRP_CNT_SRC_MII)
Register #:
1C16h
Size:
32 bits
This register counts the number of packets received on Port 0(Host MAC) that were dropped by the
Buffer Manager due to ingress rate limit discarding (Red and random Yellow dropping).
BITS
31:0
DESCRIPTION
Dropped Count
These bits count the number of dropped packets received on Port 0(Host
MAC) and is cleared when read.
Note:
SMSC LAN9312
TYPE
DEFAULT
RC
00000000h
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
435
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.24
Buffer Manager Port 1 Ingress Rate Drop Count Register (BM_RATE_DRP_CNT_SRC_1)
Register #:
1C17h
Size:
32 bits
This register counts the number of packets received on Port 1 that were dropped by the Buffer
Manager due to ingress rate limit discarding (Red and random Yellow dropping).
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Dropped Count
These bits count the number of dropped packets received on Port 1 and is
cleared when read.
RC
00000000h
Note:
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
Revision 2.0 (02-14-13)
436
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.25
Buffer Manager Port 2 Ingress Rate Drop Count Register (BM_RATE_DRP_CNT_SRC_2)
Register #:
1C18h
Size:
32 bits
This register counts the number of packets received on Port 2 that were dropped by the Buffer
Manager due to ingress rate limit discarding (Red and random Yellow dropping).
BITS
DESCRIPTION
TYPE
DEFAULT
31:0
Dropped Count
These bits count the number of dropped packets received on Port 2 and is
cleared when read.
RC
00000000h
Note:
SMSC LAN9312
This counter will stop at its maximum value of FFFF_FFFFh.
Minimum rollover time at 100Mbps is approximately 481 hours.
437
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.26
Buffer Manager Interrupt Mask Register (BM_IMR)
Register #:
1C20h
Size:
32 bits
This register contains the Buffer Manager interrupt mask, which masks the interrupts in the Buffer
Manager Interrupt Pending Register (BM_IPR). All Buffer Manager interrupts are masked by setting
the Interrupt Mask bit. Clearing this bit will unmask the interrupts. Refer to Chapter 5, "System
Interrupts," on page 49 for more information.
BITS
31:1
0
DESCRIPTION
TYPE
DEFAULT
RESERVED
RO
-
Interrupt Mask
When set, this bit masks interrupts from the Buffer Manager. The status bits
in the Buffer Manager Interrupt Pending Register (BM_IPR) are not affected.
R/W
1b
Revision 2.0 (02-14-13)
438
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
14.5.4.27
Buffer Manager Interrupt Pending Register (BM_IPR)
Register #:
1C21h
Size:
32 bits
This register contains the Buffer Manager interrupt status. The status is double buffered. All interrupts
in this register may be masked via the Buffer Manager Interrupt Mask Register (BM_IMR) register.
Refer to Chapter 5, "System Interrupts," on page 49 for more information.
BITS
DESCRIPTION
TYPE
DEFAULT
31:14
RESERVED
RO
-
13:10
Drop Reason B
When bit 7 is set, these bits indicate the reason a packet was dropped per
the table below:
RC
0h
RC
00b
RC
0b
BIT
VALUES
9:8
DESCRIPTION
0000
The destination address was not in the ALR table (unknown or broadcast), and
the Broadcast Buffer Level was exceeded.
0001
Drop on Red was set and the packet was colored Red.
0010
There were no buffers available.
0011
There were no memory descriptors available.
0100
The destination address was not in the ALR table (unknown or broadcast) and
there were no valid destination ports.
0101
The packet had a receive error and was >64 bytes
0110
The Buffer Drop Level was exceeded.
0111
RESERVED
1000
RESERVED
1001
Drop on Yellow was set, the packet was colored Yellow and was randomly
selected to be dropped.
1010
RESERVED
1011
RESERVED
1100
RESERVED
1101
RESERVED
1110
RESERVED
1111
RESERVED
Source Port B
When bit 7 is set, these bits indicate the source port on which the packet
was dropped.
00 = Port 0
01 = Port 1
10 = Port 2
11 = RESERVED
7
Status B Pending
When set, bits 13:8 are valid.
SMSC LAN9312
439
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
BITS
DESCRIPTION
TYPE
DEFAULT
6:3
Drop Reason A
When bit 0 is set, these bits indicate the reason a packet was dropped. See
the Drop Reason B description above for definitions of each value of this
field.
RC
0h
2:1
Source port A
When bit 0 is set, these bits indicate the source port on which the packet
was dropped.
RC
00b
RC
0b
00 = Port 0
01 = Port 1
10 = Port 2
11 = RESERVED
0
Set A Valid
When set, bits 6:1 are valid.
Revision 2.0 (02-14-13)
440
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 15 Operational Characteristics
15.1
Absolute Maximum Ratings*
Supply Voltage (VDD33A1, VDD33A2, VDD33BIAS, VDD33IO) (Note 15.1) . . . . . . . . . . . 0V to +3.6V
Positive voltage on signal pins, with respect to ground (Note 15.2) . . . . . . . . . . . . . . . . . . . . . . . . . +6V
Negative voltage on signal pins, with respect to ground (Note 15.3) . . . . . . . . . . . . . . . . . . . . . . . -0.5V
Positive voltage on XI, with respect to ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.6V
Positive voltage on XO, with respect to ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5V
Ambient Operating Temperature in Still Air (TA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to +70oC
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55oC to +150oC
Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020
HBM ESD Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..+/- 5kV
Note 15.1 When powering this device from laboratory or system power supplies, it is important that
the absolute maximum ratings not be exceeded or device failure can result. Some power
supplies exhibit voltage spikes on their outputs when AC power is switched on or off. In
addition, voltage transients on the AC power line may appear on the DC output. If this
possibility exists, it is suggested that a clamp circuit be used.
Note 15.2 This rating does not apply to the following pins: XI, XO, EXRES.
Note 15.3 This rating does not apply to the following pins: EXRES.
*Stresses exceeding those listed in this section could cause permanent damage to the device. This is
a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Functional operation of the device at any condition exceeding those indicated in
Section 15.2, "Operating Conditions**", Section 15.4, "DC Specifications", or any other applicable
section of this specification is not implied. Note, device signals are NOT 5 volt tolerant.
15.2
Operating Conditions**
Supply Voltage (VDD33A1, VDD33A2, VDD33BIAS, VDD33IO). . . . . . . . . . . . . . . . . +3.3V +/- 300mV
Ambient Operating Temperature in Still Air (TA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to +70oC
**Proper operation of the LAN9312 is guaranteed only within the ranges specified in this section.
SMSC LAN9312
441
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.3
Power Consumption
This section details the power consumption of the LAN9312. Power consumption values are provided
for both the device-only, and for the device plus the Ethernet components on ports 1 and 2.
Table 15.1 Supply and Current (10BASE-T Full-Duplex)
TYPICAL
(@ 3.3V)
MAXIMUM
(@ 3.6V)
UNIT
Supply current at 3.3V
(VDD33A1, VDD33A2, VDD33BIAS, VDD33IO)
165
185
mA
Power Dissipation (Device Only)
550
670
mW
Power Dissipation (Device and Ethernet components)
1245
1435
mW
25
Note 15.4
oC
PARAMETER
Ambient Operating Temperature in Still Air (TA)
Table 15.2 Supply and Current (100BASE-TX Full-Duplex)
TYPICAL
(@ 3.3V)
MAXIMUM
(@ 3.6V)
UNIT
Supply current
(VDD33A1, VDD33A2, VDD33BIAS, VDD33IO)
255
295
mA
Power Dissipation (Device Only)
845
1070
mW
Power Dissipation (Device and Ethernet components)
1130
1385
mW
25
Note 15.4
oC
PARAMETER
Ambient Operating Temperature in Still Air (TA)
Note 15.4 Over the conditions specified in Section 15.2, "Operating Conditions**".
Note: Power dissipation is determined by operating frequency, temperature, and supply voltage, as
well as external source/sink current requirements.
Revision 2.0 (02-14-13)
442
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.4
DC Specifications
Table 15.3 I/O Buffer Characteristics
PARAMETER
SYMBOL
MIN
Low Input Level
VILI
-0.3
High Input Level
VIHI
Negative-Going Threshold
VILT
1.01
Positive-Going Threshold
VIHT
SchmittTrigger Hysteresis
(VIHT - VILT)
TYP
MAX
UNITS
NOTES
IS Type Input Buffer
V
3.6
V
1.18
1.35
V
Schmitt trigger
1.39
1.6
1.8
V
Schmitt trigger
VHYS
345
420
485
mV
Input Leakage
IIN
-10
10
uA
Input Capacitance
CIN
3
pF
Low Output Level
VOL
0.4
V
IOL = 8mA
High Output Level
VOH
V
IOH = -8mA
Note 15.5
O8 Type Buffers
VDD33IO - 0.4
OD8 Type Buffer
Low Output Level
VOL
0.4
V
IOL = 8mA
Low Output Level
VOL
0.4
V
IOL = 12mA
High Output Level
VOH
V
IOH = -12mA
V
IOL = 12mA
O12 Type Buffer
VDD33IO - 0.4
OD12 Type Buffer
Low Output Level
VOL
0.4
Note 15.6
ICLK Type Buffer (XI Input)
Low Input Level
VILI
-0.3
0.5
V
High Input Level
VIHI
1.4
3.6
V
Note 15.5 This specification applies to all IS type inputs and tri-stated bi-directional pins. Internal pulldown and pull-up resistors add +/- 50uA per-pin (typical).
Note 15.6 XI can optionally be driven from a 25MHz single-ended clock oscillator.
Table 15.4 100BASE-TX Transceiver Characteristics
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
NOTES
Peak Differential Output Voltage High
VPPH
950
-
1050
mVpk
Note 15.7
Peak Differential Output Voltage Low
VPPL
-950
-
-1050
mVpk
Note 15.7
Signal Amplitude Symmetry
VSS
98
-
102
%
Note 15.7
Signal Rise and Fall Time
TRF
3.0
-
5.0
nS
Note 15.7
Rise and Fall Symmetry
TRFS
-
-
0.5
nS
Note 15.7
Duty Cycle Distortion
DCD
35
50
65
%
Note 15.8
SMSC LAN9312
443
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 15.4 100BASE-TX Transceiver Characteristics (continued)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
VOS
-
-
5
%
1.4
nS
Overshoot and Undershoot
Jitter
NOTES
Note 15.9
Note 15.7 Measured at line side of transformer, line replaced by 100Ω (+/- 1%) resistor.
Note 15.8 Offset from 16nS pulse width at 50% of pulse peak.
Note 15.9 Measured differentially.
Table 15.5 10BASE-T Transceiver Characteristics
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
NOTES
Transmitter Peak Differential Output Voltage
VOUT
2.2
2.5
2.8
V
Note 15.10
Receiver Differential Squelch Threshold
VDS
300
420
585
mV
Note 15.10 Min/max voltages guaranteed as measured with 100Ω resistive load.
15.5
AC Specifications
This section details the various AC timing specifications of the LAN9312.
Note: The I2C timing adheres to the Philips I2C-Bus Specification. Refer to the Philips I2C-Bus
Specification for detailed I2C timing information.
15.5.1
Equivalent Test Load
Output timing specifications assume the 25pF equivalent test load illustrated in Figure 15.1 below.
OUTPUT
25 pF
Figure 15.1 Output Equivalent Test Load
Revision 2.0 (02-14-13)
444
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.5.2
Reset and Configuration Strap Timing
This diagram illustrates the nRST pin timing requirements and its relation to the configuration strap
pins and output drive. Assertion of nRST is not a requirement. However, if used, it must be asserted
for the minimum period specified. Please refer to Section 4.2, "Resets," on page 36 for additional
information.
trstia
nRST
tcss
tcsh
Configuration
Strap Pins
todad
Output Drive
Figure 15.2 nRST Reset Pin Timing
Table 15.6 nRST Reset Pin Timing Values
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
trstia
nRST input assertion time
200
μS
tcss
Configuration strap pins setup to nRST deassertion
200
nS
tcsh
Configuration strap pins hold after nRST deassertion
10
nS
todad
Output drive after deassertion
30
nS
Note: Device configuration straps are latched as a result of nRST assertion. Refer to Section 4.2.4,
"Configuration Straps," on page 40 for details.
SMSC LAN9312
445
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.5.3
Power-On Configuration Strap Valid Timing
This diagram illustrates the configuration strap valid timing requirements in relation to power-on. In
order for valid configuration strap values to be read at power-on, the following timing requirements
must be met.
VDD33IO
2.0V
tcfg
Configuration Straps
Figure 15.3 Power-On Configuration Strap Latching Timing
Table 15.7 Power-On Configuration Strap Latching Timing Values
SYMBOL
tcfg
DESCRIPTION
MIN
Configuration strap valid time
TYP
MAX
UNITS
15
mS
Note: Configuration straps must only be pulled high or low. Configuration straps must not be driven
as inputs.
Note: Device configuration straps are also latched as a result of nRST assertion. Refer to Section
15.5.2, "Reset and Configuration Strap Timing," on page 445 and Section 4.2.4, "Configuration
Straps," on page 40 for additional details.
Revision 2.0 (02-14-13)
446
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.5.4
PIO Read Cycle Timing
Please refer to Section 8.4.4, "PIO Reads," on page 106 for a functional description of this mode.
A[x:2], END_SEL
tcycle
tasu
tah
tcsl
tcsh
nCS, nRD
tdoff
tcsdv
tdoh
tdon
D[31:0]
Figure 15.4 PIO Read Cycle Timing
Table 15.8 PIO Read Cycle Timing Values
SYMBOL
DESCRIPTION
tcycle
MIN
TYP
MAX
UNITS
Read Cycle Time
45
nS
tcsl
nCS, nRD Assertion Time
32
nS
tcsh
nCS, nRD De-assertion Time
13
nS
tcsdv
nCS, nRD Valid to Data Valid
tasu
Address setup to nCS, nRD Valid
0
nS
tah
Address Hold Time
0
nS
tdon
Data Buffer Turn On Time
0
nS
tdoff
Data Buffer Turn Off Time
tdoh
Data Output Hold Time
30
9
0
nS
nS
nS
Note: A host PIO read cycle begins when both nCS and nRD are asserted. The cycle ends when
either or both nCS and nRD are de-asserted. These signals may be asserted and de-asserted
in any order.
SMSC LAN9312
447
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.5.5
PIO Burst Read Cycle Timing
Please refer to Section 8.4.5, "PIO Burst Reads," on page 107 for a functional description of this mode.
A[x:5], END_SEL
tacyc
tacyc
tacyc
A[4:2]
tah
tasu
tcsh
nCS, nRD
tcsdv
tdon
tadv
tadv
tadv
tdoff
tdoh
D[31:0]
Figure 15.5 PIO Burst Read Cycle Timing
Table 15.9 PIO Burst Read Cycle Timing Values
SYMBOL
DESCRIPTION
MIN
TYP
MAX
13
UNITS
tcsh
nCS, nRD De-assertion Time
nS
tcsdv
nCS, nRD Valid to Data Valid
tacyc
Address Cycle Time
45
nS
tasu
Address Setup to nCS, nRD Valid
0
nS
tadv
Address Stable to Data Valid
tah
Address Hold Time
0
nS
tdon
Data Buffer Turn On Time
0
nS
tdoff
Data Buffer Turn Off Time
tdoh
Data Output Hold Time
30
40
9
0
nS
nS
nS
nS
Note: A host PIO burst read cycle begins when both nCS and nRD are asserted. The cycle ends
when either or both nCS and nRD are de-asserted. These signals may be asserted and deasserted in any order.
Note:
Revision 2.0 (02-14-13)
Fresh data is supplied each time A[2] toggles.
448
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.5.6
RX Data FIFO Direct PIO Read Cycle Timing
Please refer to Section 8.4.6, "RX Data FIFO Direct PIO Reads," on page 108 for a functional
description of this mode.
FIFO_SEL
A[x:2], END_SEL
tcycle
tasu
tah
tcsl
tcsh
nCS, nRD
tdoff
tcsdv
tdoh
tdon
D[31:0]
Figure 15.6 RX Data FIFO Direct PIO Read Cycle Timing
Table 15.10 RX Data FIFO Direct PIO Read Cycle Timing Values
SYMBOL
DESCRIPTION
tcycle
MIN
TYP
MAX
UNITS
Read Cycle Time
45
nS
tcsl
CS, nRD Assertion Time
32
nS
tcsh
nCS, nRD De-assertion Time
13
nS
tcsdv
nCS, nRD Valid to Data Valid
tasu
Address, FIFO_SEL Setup to nCS, nRD Valid
0
nS
tah
Address, FIFO_SEL Hold Time
0
nS
tdon
Data Buffer Turn On Time
0
nS
tdoff
Data Buffer Turn Off Time
tdoh
Data Output Hold Time
30
9
0
nS
nS
nS
Note: A RX Data FIFO direct PIO read cycle begins when both nCS and nRD are asserted. The cycle
ends when either or both nCS and nRD are de-asserted. They may be asserted and deasserted in any order.
SMSC LAN9312
449
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.5.7
RX Data FIFO Direct PIO Burst Read Cycle Timing
Please refer to Section 8.4.7, "RX Data FIFO Direct PIO Burst Reads," on page 109 for a functional
description of this mode.
FIFO_SEL
END_SEL
tacyc
tacyc
tacyc
A[2]
tah
tasu
tcsh
nCS, nRD
tcsdv
tdon
tadv
tadv
tadv
tdoff
tdoh
D[31:0]
Figure 15.7 RX Data FIFO Direct PIO Burst Read Cycle Timing
Table 15.11 RX Data FIFO Direct PIO Burst Read Cycle Timing Values
SYMBOL
DESCRIPTION
MIN
TYP
MAX
13
UNITS
tcsh
nCS, nRD De-assertion Time
nS
tcsdv
nCS, nRD Valid to Data Valid
tacyc
Address Cycle Time
45
nS
tasu
Address, FIFO_SEL Setup to nCS, nRD Valid
0
nS
tadv
Address Stable to Data Valid
tah
Address, FIFO_SEL Hold Time
0
nS
tdon
Data Buffer Turn On Time
0
nS
tdoff
Data Buffer Turn Off Time
tdoh
Data Output Hold Time
30
40
9
0
nS
nS
nS
nS
Note: A RX Data FIFO direct PIO burst read cycle begins when both nCS and nRD are asserted.
The cycle ends when either or both nCS and nRD are de-asserted. They may be asserted and
de-asserted in any order.
Note:
Revision 2.0 (02-14-13)
Fresh data is supplied each time A[2] toggles.
450
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.5.8
PIO Write Cycle Timing
Please refer to Section 8.4.8, "PIO Writes," on page 110 for a functional description of this mode.
A[x:2], END_SEL
tcycle
tasu
tah
tcsl
tcsh
nCS, nWR
tdsu
tdh
D[31:0]
Figure 15.8 PIO Write Cycle Timing
Table 15.12 PIO Write Cycle Timing Values
SYMBOL
DESCRIPTION
tcycle
MIN
TYP
MAX
UNITS
Write Cycle Time
45
nS
tcsl
nCS, nWR Assertion Time
32
nS
tcsh
nCS, nWR De-assertion Time
13
nS
tasu
Address Setup to nCS, nWR Assertion
0
nS
tah
Address Hold Time
0
nS
tdsu
Data Setup to nCS, nWR De-assertion
7
nS
tdh
Data Hold Time
0
nS
Note: A PIO write cycle begins when both nCS and nWR are asserted. The cycle ends when either
or both nCS and nWR are de-asserted. These signals may be asserted and de-asserted in any
order.
SMSC LAN9312
451
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.5.9
TX Data FIFO Direct PIO Write Cycle Timing
Please refer to Section 8.4.9, "TX Data FIFO Direct PIO Writes," on page 111 for a functional
description of this mode.
FIFO_SEL
A[2], END_SEL
tcycle
tasu
tah
tcsl
tcsh
nCS, nWR
tdsu
tdh
D[31:0]
Figure 15.9 TX Data FIFO Direct PIO Write Cycle Timing
Table 15.13 TX Data FIFO Direct PIO Write Cycle Timing Values
SYMBOL
tcycle
DESCRIPTION
MIN
TYP
MAX
UNITS
Write Cycle Time
45
nS
tcsl
nCS, nWER Assertion Time
32
nS
tcsh
nCS, nWR De-assertion Time
13
nS
tasu
Address, FIFO_SEL Setup to nCS, nWR Assertion
0
nS
tah
Address, FIFO_SEL Hold Time
0
nS
tdsu
Data Setup to nCS, nWR De-assertion
7
nS
tdh
Data Hold Time
0
nS
Note: A TX Data FIFO direct PIO write cycle begins when both nCS and nWR are asserted. The
cycle ends when either or both nCS and nWR are de-asserted. They may be asserted and deasserted in any order.
Revision 2.0 (02-14-13)
452
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.5.10
Microwire Timing
This section specifies the Microwire EEPROM interface timing requirements. Please refer to Section
10.2.3, "Microwire EEPROM," on page 144 for a functional description of this serial interface.
tcsl
EECS
tcshckh
tckcyc
tckh
tckl
tcklcsl
EECLK
tckldis
tdvckh tckhdis
EEDO
tdsckh
tdhckh
EEDI
tdhcsl
tcshdv
EEDI (VERIFY)
Figure 15.10 Microwire Timing
Table 15.14 Microwire Timing Values
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNITS
tckcyc
EECLK cycle time
1110
1130
nS
tckh
EECLK high time
550
570
nS
tckl
EECLK low time
550
570
nS
tcshckh
EECS high before rising edge of EECLK
1070
nS
tcklcsl
EECLK falling edge to EECS low
30
nS
tdvckh
EEDO valid before rising edge of EECLK
550
nS
tckhdis
EEDO disable after rising edge of EECLK
550
nS
tdsckh
EEDI setup to rising edge of EECLK
90
nS
tdhckh
EEDI hold after rising edge of EECLK
0
nS
tckldis
EECLK low to EEDO data disable
580
nS
tcshdv
EEDI valid after EECS high (VERIFY)
tdhcsl
EEDI hold after EECS low (VERIFY)
tcsl
SMSC LAN9312
600
EECS low
453
DATASHEET
nS
0
nS
1070
nS
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
15.6
Clock Circuit
The LAN9312 can accept either a 25MHz crystal (preferred) or a 25MHz single-ended clock oscillator
(+/- 50ppm) input. If the single-ended clock oscillator method is implemented, XO should be left
unconnected and XI should be driven with a nominal 0-3.3V clock signal. The input clock duty cycle
is 40% minimum, 50% typical and 60% maximum.
It is recommended that a crystal utilizing matching parallel load capacitors be used for the crystal
input/output signals (XI/XO). See Table 15.15 for crystal specifications.
Table 15.15 LAN9312Crystal Specifications
PARAMETER
SYMBOL
MIN
NOM
Crystal Cut
MAX
UNITS
NOTES
AT, typ
Crystal Oscillation Mode
Fundamental Mode
Crystal Calibration Mode
Parallel Resonant Mode
Frequency
Ffund
-
25.000
-
MHz
Frequency Tolerance @ 25oC
Ftol
-
-
+/-50
PPM
Note 15.11
Frequency Stability Over Temp
Ftemp
-
-
+/-50
PPM
Note 15.11
Frequency Deviation Over Time
Fage
-
+/-3 to 5
-
PPM
Note 15.12
-
-
+/-50
PPM
Note 15.13
Total Allowable PPM Budget
Shunt Capacitance
CO
-
7 typ
-
pF
Load Capacitance
CL
-
20 typ
-
pF
Drive Level
PW
300
-
-
uW
Equivalent Series Resistance
R1
-
-
50
Ohm
Operating Temperature Range
0
-
+70
oC
n/a XI Pin Capacitance
-
3 typ
-
pF
Note 15.14
n/a XO Pin Capacitance
-
3 typ
-
pF
Note 15.14
Note 15.11 The maximum allowable values for Frequency Tolerance and Frequency Stability are
application dependant. Since any particular application must meet the IEEE +/-50 PPM
Total PPM Budget, the combination of these two values must be approximately +/-45 PPM
(allowing for aging).
Note 15.12 Frequency Deviation Over Time is also referred to as Aging.
Note 15.13 The total deviation for the Transmitter Clock Frequency is specified by IEEE 802.3 as
+/- 50 PPM.
Note 15.14 This number includes the pad, the bond wire and the lead frame. PCB capacitance is not
included in this value. The XO/XI pin and PCB capacitance values are required to
accurately calculate the value of the two external load capacitors. These two external load
capacitors determine the accuracy of the 25.000 MHz frequency.
Revision 2.0 (02-14-13)
454
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 16 Package Outlines
16.1
128-VTQFP Package Outline
Figure 16.1 128-VTQFP Package Definition
Table 16.1 128-VTQFP Dimensions
MIN
NOMINAL
MAX
REMARKS
A
-
-
1.20
Overall Package Height
A1
0.05
-
0.15
Standoff
A2
0.95
1.00
1.05
Body Thickness
D/E
15.80
16.00
16.20
X/Y Span
D1/E1
13.80
14.00
14.20
X/Y Plastic Body Size
L
0.45
0.60
0.75
Lead Foot Length
b
0.13
0.18
0.23
Lead Width
c
0.09
-
0.20
Lead Foot Thickness
e
0.40 BSC
Lead Pitch
ddd
0.00
-
0.07
True Position Spread
ccc
-
-
0.08
Coplanarity
SMSC LAN9312
455
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Notes:
1. All dimensions are in millimeters unless otherwise noted.
2. Dimensions b & c apply to the flat section of the lead foot between 0.10 and 0.25mm from the lead tip. The
base metal is exposed at the lead tip.
3. Dimensions D1 and E1 do not include mold protrusions. Maximum allowed protrusion is 0.25mm per side. D1
and E1 are maximum plastic body size dimensions including mold mismatch.
4. The pin 1 identifier may vary, but is always located within the zone indicated
.
Figure 16.2 128-VTQFP Recommended PCB Land Pattern
Revision 2.0 (02-14-13)
456
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
16.2
128-XVTQFP Package Outline
Figure 16.3 128-XVTQFP Package Definition
SMSC LAN9312
457
DATASHEET
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 16.2 128-XVTQFP Dimensions
A
MIN
NOMINAL
MAX
REMARKS
-
-
1.20
Overall Package Height
A1
0.05
-
0.15
Standoff
A2
0.95
1.00
1.05
Body Thickness
D/E
15.80
16.00
16.20
X/Y Span
D1/E1
13.80
14.00
14.20
X/Y Plastic Body Size
D2/E2
4.85
5.00
5.15
X/Y Exposed Pad Size
L
0.45
0.60
0.75
Lead Foot Length
b
0.13
0.18
0.23
Lead Width
c
0.09
-
0.20
Lead Foot Thickness
e
0.40 BSC
Lead Pitch
ddd
0.00
-
0.07
True Position Spread
ccc
-
-
0.08
Coplanarity
Notes:
1. All dimensions are in millimeters unless otherwise noted.
2. Dimensions b & c apply to the flat section of the lead foot between 0.10 and 0.25mm from the lead tip. The
base metal is exposed at the lead tip.
3. Dimensions D1 and E1 do not include mold protrusions. Maximum allowed protrusion is 0.25mm per side. D1
and E1 are maximum plastic body size dimensions including mold mismatch.
4. Dimensions D2 and E2 represent the size of the exposed pad. The exposed pad shall be coplanar with the
bottom of the package within 0.05mm.
5. The pin 1 identifier may vary, but is always located within the zone indicated
.
Figure 16.4 128-XVTQFP Recommended PCB Land Pattern
Revision 2.0 (02-14-13)
458
DATASHEET
SMSC LAN9312
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Chapter 17 Datasheet Revision History
Table 17.1 Customer Revision History
REVISION LEVEL & DATE
SECTION/FIGURE/ENTRY
CORRECTION
Rev. 2.0 (02-14-13)
Chapter 3, "Pin Description
and Configuration," on
page 26
Changed “Refer to the LAN9312 application note
for additional connection information.” to “Refer to
the LAN9312 reference schematic for additional
connection information.” in the VDD18TX1,
VDD18TX2, VDD18PLL, VDD33IO, VDD18CORE,
VDD33A1, VDD33A2, and VDD33BIAS pin
descriptions.
Rev. 1.9 (03-13-12)
Order Codes
Updated ordering codes to include tape and reel
options.
Rev. 1.8 (07-07-11)
Figure 16.3 128-XVTQFP
Package Definition on
page 457, Table 16.2, “128XVTQFP Dimensions,” on
page 458, and Figure 16.4
128-XVTQFP
Recommended PCB Land
Pattern on page 458
Updated 128-XVTQFP package dimensions and
figures.
Rev. 1.7 (06-29-10)
Table 3.5, “EEPROM Pins,”
on page 31
Added note to EE_SDA and EE_SCL pin
descriptions stating “If I2C is selected, an external
pull-up is required when using an EEPROM and is
recommended if no EEPROM is attached.”
Table 3.5, “EEPROM Pins,”
on page 31
Added note to EEDO/EEPROM_TYPE pin
descriptions stating “When not using a Microwire
or I2C EEPROM, an external pull-down resistor is
recommended on this pin.”
Section 14.2.8.4, "Virtual
PHY Identification LSB
Register (VPHY_ID_LSB),"
on page 251 and Section
14.4.2.4, "Port x PHY
Identification LSB Register
(PHY_ID_LSB_x)," on
page 293
Clarified default values using binary.
Section 14.5.2.23, "Port x
MAC Transmit Configuration
Register
(MAC_TX_CFG_x)," on
page 345
Added note to IFG Config field description:
Section 14.3.6, "Host MAC
MII Access Register
(HMAC_MII_ACC)," on
page 278
Corrected MIIBZY bit type to read only, selfclearing
Table 6.1, “Switch Fabric
Flow Control Enable Logic,”
on page 59
Corrected rightmost column title to “TX FLOW
CONTROL ENABLE”
Figure 15.2 nRST Reset Pin
Timing on page 445
Updated figure shading.
All
Standard SMSC formatting applied.
Rev. 1.6 (08-19-09)
SMSC LAN9312
459
Note:
DATASHEET
IFG Config values less than 15 are
unsupported.
Revision 2.0 (02-14-13)
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
Datasheet
Table 17.1 Customer Revision History (continued)
REVISION LEVEL & DATE
SECTION/FIGURE/ENTRY
Rev. 1.5 (10-28-08)
Section 14.2.4.1, "EEPROM
Command Register
(E2P_CMD)," on page 197
Corrected CFG_LOADED bit type from “RO” to
“R/WC”
Section 15.6, "Clock
Circuit," on page 454
Changed max ESR value from 30 to 50 Ohms and
corrected typos in operating temerpature range.
All
Fixed various typos
Port x PHY Special
Control/Status Register
(PHY_SPECIAL_CONTROL
_STATUS_x) on page 307
Updated RESERVED bits 11:5 definition to
“RESERVED - Write as 0000010b, ignore on
read”, changed default to 0000010b, and made
field R/W.
Wake-Up Frame Detection
section of Host MAC
Chapter and MAC_CR
register description
Added note at end of WUFF section and to the
BCAST bit of the MAC_CR register stating:
When wake-up frame detection is enabled via the
WUEN bit of the HMAC_WUCSR register, a
broadcast wake-up frame will wake-up the device
despite the state of the Disable Broadcast Frames
(BCAST) bit in the HMAC_CR register.
HMAC_WUCSR register
Fixed error in GUE bit description: “....the MAC
Address [1:0] bits...” changed to “...the MAC
Address [0] bits....”.
Port x PHY Auto-Negotiation
Advertisement Register
(PHY_AN_ADV_x) on page
294
Bits 15 and 9 made RESERVED.
Section 15.6, "Clock
Circuit," on page 454
Changed minimum drive level from 0.5mW to
300uW
Rev. 1.3 (07-03-08)
Revision 2.0 (02-14-13)
460
CORRECTION
DATASHEET
SMSC LAN9312
Similar pages