MCNIX MX29F001TQC-12 1m-bit [128k x 8] cmos flash memory Datasheet

MX29F001T/B
1M-BIT [128K x 8] CMOS FLASH MEMORY
FEATURES
5.0V ± 10% for read, erase and write operation
131072x8 only organization
Fast access time: 90/120ns
Low power consumption
- 30mA maximum active current(5MHz)
- 1uA typical standby current
• Command register architecture
- Byte Programming (7us typical)
- Sector Erase (8K-Byte x 1, 4K-Byte x 2, 8K Byte
x 2, 32K-Byte x 1, and 64K-Byte x 1)
• Auto Erase (chip & sector) and Auto Program
- Automatically erase any combination of sectors
with Erase Suspend capability.
- Automatically programs and verifies data at
specified address
• Erase Suspend/Erase Resume
– Suspends an erase operation to read data from,
or program data to, a sector that is not being
erased, then resumes the erase operation.
•
•
•
•
• Status Reply
- Data polling & Toggle bit for detection of program
and erase cycle completion.
• Chip protect/unprotect for 5V only system or 5V/12V
system
• 100,000 minimum erase/program cycles
• Latch-up protected to 100mA from -1 to VCC+1V
• Boot Code Sector Architecture
- T = Top Boot Sector
- B = Bottom Boot Sector
• Low VCC write inhibit is equal to or less than 3.2V
• Package type:
- 32-pin PLCC
- 32-pin TSOP
- 32-pin PDIP
• Boot Code Sector Architecture
- T=Top Boot Sector
- B=Bottom Boot Sector
• 20 years data retention
GENERAL DESCRIPTION
The MX29F001T/B is a 1-mega bit Flash memory
organized as 128K bytes of 8 bits only MXIC's
Flash memories offer the most cost-effective and
reliable read/write non-volatile random access
memory. The MX29F001T/B is packaged in 32-pin
PLCC, TSOP, PDIP. It is designed to be reprogrammed and erased in-system or in-standard
EPROM programmers.
programming, while maintaining maximum EPROM
compatibility.
MXIC Flash technology reliably stores memory contents even after 100,000 erase and program cycles.
The MXIC cell is designed to optimize the erase and
programming mechanisms. In addition, the combination of advanced tunnel oxide processing and low
internal electric fields for erase and programming
operations produces reliable cycling.
The
MX29F001T/B uses a 5.0V ± 10% VCC supply to
perform the High Reliability Erase and auto
Program/Erase algorithms.
The standard MX29F001T/B offers access time
90ns. To eliminate bus contention, the MX29F001T/
B has separate chip enable (CE) and output enable
(OE) controls.
MXIC's Flash memories augment EPROM functionality with in-circuit electrical erasure and
programming. The MX29F001T/B uses a command
register to manage this functionality. The command
register allows for 100% TTL level control inputs
and fixed power supply levels during erase and
The highest degree of latch-up protection is
achieved with MXIC's proprietary non-epi process.
Latch-up protection is proved for stresses up to 100
milliamps on address and data pin from -1V to VCC
+ 1V.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
1
MX29F001T/B
A7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
32
WE
VCC
A16
4
30
29
A14
A6
A13
A5
A8
A4
A3
A9
MX29F001T/B
9
25
A11
A2
OE
A1
A10
A0
CE
21
20
Q5
Q4
Q3
17
Q7
Q6
13
14
GND
Q0
32 TSOP (TYPE 1)
A11
A9
A8
A13
A14
NC
WE
VCC
NC
A16
A15
A12
A7
A6
A5
A4
5
NC
VCC
WE
NC
A14
A13
A8
A9
A11
OE
A10
CE
Q7
Q6
Q5
Q4
Q3
Q2
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
Q1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
MX29F001T/B
NC
A16
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
Q0
Q1
Q2
GND
A15
32 PLCC
A12
32 PDIP
NC
PIN CONFIGURATIONS
PIN DESCRIPTION:
MX29F001T/B
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
OE
A10
CE
Q7
Q6
Q5
Q4
Q3
GND
Q2
Q1
Q0
A0
A1
A2
A3
SYMBOL
PIN NAME
A0~A16
Address Input
Q0~Q7
Data Input/Output
CE
Chip Enable Input
WE
Write Enable Input
OE
Output Enable Input
VCC
Power Supply Pin (+5V)
GND
Ground Pin
(NORMAL TYPE)
SECTOR STRUCTURE
A16~A0
A16~A0
1FFFFH
1DFFFH
1CFFFH
1BFFFH
19FFFH
17FFFH
0FFFFH
8
K-BYTE
4
K-BYTE
1FFFFH
0FFFFH
64
K-BYTE
32
K-BYTE
07FFFH
4
K-BYTE
8
K-BYTE
8
K-BYTE
32
K-BYTE
64
K-BYTE
05FFFH
03FFFH
02FFFH
01FFFH
8
K-BYTE
8
K-BYTE
4
K-BYTE
4
K-BYTE
8
K-BYTE
00000H
00000H
MX29F001T Sector Architecture
MX29F001B Sector Architecture
P/N: PM0515
REV. 2.6, DEC. 29, 2003
2
MX29F001T/B
BLOCK DIAGRAM
WRITE
CE
OE
WE
CONTROL
PROGRAM/ERASE
STATE
INPUT
LOGIC
HIGH VOLTAGE
MACHINE
(WSM)
LATCH
A0-A16
BUFFER
FLASH
REGISTER
ARRAY
ARRAY
Y-DECODER
AND
X-DECODER
ADDRESS
STATE
MX29F001T/B
Y-PASS GATE
SOURCE
HV
COMMAND
DATA
DECODER
SENSE
AMPLIFIER
PGM
DATA
HV
COMMAND
DATA LATCH
PROGRAM
DATA LATCH
Q0-Q7
I/O BUFFER
P/N: PM0515
REV. 2.6, DEC. 29, 2003
3
MX29F001T/B
AUTOMATIC PROGRAMMING
AUTOMATIC ERASE ALGORITHM
The MX29F001T/B is byte programmable using the Automatic Programming algorithm. The Automatic Programming algorithm does not require the system to time out
or verify the data programmed. The typical chip programming time of the MX29F001T/B at room temperature is less than 3.5 seconds.
AUTOMATIC CHIP ERASE
MXIC's Automatic Erase algorithm requires the user to
write commands to the command register using standard microprocessor write timings. The device will automatically pre-program and verify the entire array. Then
the device automatically times the erase pulse width,
provides the erase verification, and counts the number
of sequences. A status bit toggling between consecutive read cycles provides feedback to the user as to the
status of the programming operation.
The entire chip is bulk erased using 10 ms erase pulses
according to MXIC's Automatic Chip Erase algorithm.
Typical erasure at room temperature is accomplished in
less than 3 second. The Automatic Erase algorithm automatically programs the entire array prior to electrical
erase. The timing and verification of electrical erase are
internally controlled within the device.
Register contents serve as inputs to an internal statemachine which controls the erase and programming circuitry. During write cycles, the command register internally latches addresses and data needed for the programming and erase operations. During a system write
cycle, addresses are latched on the falling edge, and
data are latched on the rising edge of WE .
MXIC's Flash technology combines years of EPROM
experience to produce the highest levels of quality, reliability, and cost effectiveness. The MX29F001T/B electrically erases all bits simultaneously using FowlerNordheim tunneling. The bytes are programmed by using the EPROM programming mechanism of hot electron injection.
AUTOMATIC SECTOR ERASE
The MX29F001T/B is sector(s) erasable using MXIC's
Auto Sector Erase algorithm. Sector erase modes allow
sectors of the array to be erased in one erase cycle. The
Automatic Sector Erase algorithm automatically programs the specified sector(s) prior to electrical erase.
The timing and verification of electrical erase are internally con trolled by the device.
During a program cycle, the state-machine will control
the program sequences and command register will not
respond to any command set. During a Sector Erase
cycle, the command register will only respond to Erase
Suspend command. After Erase Suspend is completed,
the device stays in read mode. After the state machine
has completed its task, it will allow the command register to respond to its full command set.
AUTOMATIC PROGRAMMING ALGORITHM
MXIC's Automatic Programming algorithm requires the
user to only write program set-up commands (include 2
unlock write cycle and A0H) and a program command
(program data and address). The device automatically
times the programming pulse width, provides the program verification, and counts the number of sequences.
A status bit similar to DATA polling and a status bit toggling between consecutive read cycles, provides feedback to the user as to the status of the programming
operation.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
4
MX29F001T/B
TABLE 1. SOFTWARE COMMAND DEFINITIONS
Command
Bus
First Bus
Cycle
Cycle Addr
Data
Reset
1
XXXH
F0H
Read
1
RD
RD
Read Silicon ID
4
555H
Chip Protect Verify
4
555H
Second Bus
Cycle
Third Bus
Cycle
Fourth Bus
Cycle
Addr
Data
Addr Data
Addr
Data
AAH
2AAH
55H
555H 90H
ADI
DDI
AAH
2AAH
55H
555H 90H
(SA)
00H
X02H
01H
Fifth Bus
Cycle
Addr Data
Sixth Bus
Cycle
Addr Data
Program
4
555H
AAH
2AAH
55H
555H A0H
PA
PD
Chip Erase
6
555H
AAH
2AAH
55H
555H 80H
555H
AAH
2AAH
55H
555H 10H
Sector Erase
6
555H
AAH
2AAH
55H
555H 80H
555H
AAH
2AAH
55H
SA
Sector Erase Suspend 1
XXXH
B0H
Sector Erase Resume
1
XXXH
30H
Unlock for chip
6
555H
AAH
2AAH
55H
555H 80H
555H
AAH
2AAH 55H
30H
555H 20H
protect/unprotect
Note:
1. ADI = Address of Device identifier;A1=0, A0 =0 for manufacture code, A1=0, A0 =1 for device code.(Refer to
Table 3)
DDI = Data of Device identifier : C2H for manufacture code, 18H/19H for device code.
X = X can be VIL or VIH
RA=Address of memory location to be read.
RD=Data to be read at location RA.
2. PA = Address of memory location to be programmed.
PD = Data to be programmed at location PA.
SA = Address to the sector to be erased.
3. The system should generate the following address patterns: 555H or 2AAH to Address A0~A10.
Address bit A11~A16=X=Don't care for all address commands except for Program Address (PA) and Sector
Address (SA). Write Sequence may be initiated with A11~A16 in either state.
4. For chip protect verify operation : If read out data is 01H, it means the chip has been protected. If read out data
is 00H, it means the chip is still not being protected.
COMMAND DEFINITIONS
Device operations are selected by writing specific address and data sequences into the command register.
Writing incorrect address and data values or writing
them in the improper sequence will reset the device to
the read mode. Table 1 defines the valid register
command sequences. Note that the Erase Suspend
(B0H) and Erase Resume (30H) commands are valid
only while the Sector Erase operation is in progress.
Either of the two reset command sequences will reset
the device(when applicable).
P/N: PM0515
REV. 2.6, DEC. 29, 2003
5
MX29F001T/B
TABLE 2. MX29F001T/B BUS OPERATION
Pins
CE
OE
WE
A0
A1
A6
A9
Q0 ~ Q7
L
L
H
L
L
X
VID(2)
C2H
L
L
H
H
L
X
VID(2)
18H/19H
Read
L
L
H
A0
A1
A6
A9
DOUT
Standby
H
X
X
X
X
X
X
HIGH Z
Output Disable
L
H
H
X
X
X
X
HIGH Z
Write
L
H
L
A0
A1
A6
A9
DIN(3)
Chip Protect with 12V
L
VID(2)
L
X
X
L
VID(2)
X
L
VID(2)
L
X
X
H
VID(2)
X
L
L
H
X
H
X
VID(2)
Code(5)
L
H
L
X
X
L
H
X
L
H
L
X
X
H
H
X
L
L
H
X
H
X
H
Code(5)
X
X
X
X
X
X
X
HIGH Z
Mode
Read Silicon ID
Manufacturer Code(1)
Read Silicon ID
Device Code(1)
system(6)
Chip Unprotect with 12V
system(6)
Verify Chip Protect
with 12V system
Chip Protect without 12V
system (6)
Chip Unprotect without 12V
system (6)
Verify Chip Protect/Unprotect
without 12V system (7)
Reset
NOTES:
1. Manufacturer and device codes may also be accessed via a command register write sequence. Refer to Table 1.
2. VID is the Silicon-ID-Read high voltage, 11.5V to 12.5V.
3. Refer to Table 1 for valid Data-In during a write operation.
4. X can be VIL or VIH.
5. Code=00H means unprotected.
Code=01H means protected.
6. Refer to chip protect/unprotect algorithm and waveform.
Must issue "unlock for chip protect/unprotect" command before "chip protect/unprotect without 12V system"
command.
7. The "verify chip protect/unprotect without 12V system" is only following "Chip protect/unprotect without 12V
system" command.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
6
MX29F001T/B
READ/RESET COMMAND
SET-UP AUTOMATIC CHIP ERASE COMMANDS
The read or reset operation is initiated by writing the read/
reset command sequence into the command register.
Microprocessor read cycles retrieve array data. The device remains enabled for reads until the command register contents are altered.
Chip erase is a six-bus cycle operation. There are two
"unlock" write cycles. These are followed by writing the
"set-up" command 80H. Two more "unlock" write cycles
are then followed by the chip erase command 10H.
If program-fail or erase-fail happen, the write of F0H will
reset the device to abort the operation. A valid command must then be written to place the device in the
desired state.
The Automatic Chip Erase does not require the device
to be entirely pre-programmed prior to executing the Automatic Chip Erase. Upon executing the Automatic Chip
Erase, the device will automatically program and verify
the entire memory for an all-zero data pattern. When the
device is automatically verified to contain an all-zero pattern, a self-timed chip erase and verification begin. The
erase and verification operations are completed when
the data on Q7 is "1" at which time the device returns to
the Read mode. The system does not require to provide any control or timing during these operations.
SILICON-ID-READ COMMAND
Flash memories are intended for use in applications where
the local CPU alters memory contents. As such, manufacturer and device codes must be accessible while the
device resides in the target system. PROM programmers typically access signature codes by raising A9 to
a high voltage. However, multiplexing high voltage onto
address lines is not generally desired system design practice.
When using the Automatic Chip Erase algorithm, note
that the erase automatically terminates when adequate
erase margin has been achieved for the memory array(no
erase verify command is required).
The MX29F001T/B contains a Silicon-ID-Read operation
to supplement traditional PROM programming methodology. The operation is initiated by writing the read silicon ID command sequence into the command register.
Following the command write, a read cycle with
A1=VIL,A0=VIL retrieves the manufacturer code of C2H.
A read cycle with A1=VIL, A0=VIH returns the device
code of 18H for MX29F001T,19H for MX29F001B.
If the Erase operation was unsuccessful, the data on Q5
is "1"(see Table 4), indicating an erase operation exceed
internal timing limit.
The automatic erase begins on the rising edge of the
last WE pulse in the command sequence and terminates
when the data on Q7 is "1" and the data on Q6 stops
toggling for two consecutive read cycles, at which time
the device returns to the Read mode.
TABLE 3. EXPANDED SILICON ID CODE
Pins
A0
Code
Manufacture code
VIL
Device code
VIH
for MX29F001T
Device code
VIH
for MX29F001B
Chip Protection Verification X
X
A1
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
Code (Hex)
VIL
VIL
1
0
1
0
0
0
0
1
0
1
0
0
1
0
0
0
C2H
18H
VIL
0
0
0
1
1
0
0
1
19H
VIH
VIH
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
01H (Protected)
00H (Unprotected)
P/N: PM0515
REV. 2.6, DEC. 29, 2003
7
MX29F001T/B
SECTOR ERASE COMMANDS
ERASE SUSPEND
The Automatic Sector Erase does not require the device
to be entirely pre-programmed prior to executing the Automatic Set-up Sector Erase command and Automatic
Sector Erase command. Upon executing the Automatic
Sector Erase command, the device will automatically
program and verify the sector(s) memory for an all-zero
data pattern. The system does not require to provide
any control or timing during these operations.
This command only has meaning while the state machine is executing Automatic Sector Erase operation,
and therefore will only be responded during Automatic
Sector Erase operation. Writing the Erase Suspend command during the Sector Erase time-out immediately terminates the time-out immediately terminates the timeout period and suspends the erase operation. After this
command has been executed, the command register will
initiate erase suspend mode. The state machine will return to read mode automatically after suspend is ready.
At this time, state machine only allows the command
register to respond to the Read Memory Array, Erase
Resume and Program commands.
When the sector(s) is automatically verified to contain
an all-zero pattern, a self-timed sector erase and verification begin. The erase and verification operations are
complete when the data on Q7 is "1" and the data on Q6
stops toggling for two consecutive read cycles, at which
time the device returns to the Read mode. The system
does not require to provide any control or timing during
these operations.
The system can determine the status of the program
operation using the Q7 or Q6 status bits, just as in the
standard program operation. After an erase-suspend program operation is complete, the system can once again
read array data within non-suspended sectors.
When using the Automatic Sector Erase algorithm, note
that the erase automatically terminates when adequate
erase margin has been achieved for the memory array
(no erase verification command is required). Sector erase
is a six-bus cycle operation. There are two "unlock" write
cycles. These are followed by writing the set-up command 80H. Two more "unlock" write cycles are then followed by the sector erase command 30H. The sector
address is latched on the falling edge of WE, while the
command(data) is latched on the rising edge of WE. Sector addresses selected are loaded into internal register
on the sixth falling edge of WE. Each successive sector
load cycle started by the falling edge of WE must begin
within 30us from the rising edge of the preceding WE.
Otherwise, the loading period ends and internal auto sector erase cycle starts. (Monitor Q3 to determine if the
sector erase timer window is still open, see section Q3,
Sector Erase Timer.) Any command other than Sector
Erase (30H) or Erase Suspend (B0H) during the time-out
period resets the device to read mode.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
8
MX29F001T/B
Table 4. Write Operation Status
In Progress
Status
Q7
Q6
Q5
Q3
Byte Program in Auto Program Algorithm
Q7
Toggle
0
N/A
0
Toggle
0
1
Data
Data
Data
Data
Q7
Toggle
0
N/A
Auto Erase Algorithm
Erase Suspended Mode
Erase Suspend Read
Erase Suspend Program
(Non-Erase Suspended Sector)
Byte Program in Auto Program Algorithm
Exceeded
Erase in Auto Erase Algorithm
Time Limits
Erase Suspended Mode
Erase Suspend Program
(Note1)
Q7
Toggle
1
N/A
0
Toggle
1
1
Q7
Toggle
1
N/A
(Non-Erase Suspended Sector)
Note:
1. Performing successive read operations from any address will cause Q6 to toggle.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
9
MX29F001T/B
WE pulse of the six write pulse sequences for chip/sector erase.
ERASE RESUME
This command will cause the command register to clear
the suspend state and return back to Sector Erase mode
but only if an Erase Suspend command was previously
issued. Erase Resume will not have any effect in all
other conditions. Another Erase Suspend command can
be written after the chip has resumed erasing.
The Toggle Bit feature is active during Automatic Program/Erase algorithms or sector erase time-out. (see
section Q3 Sector Erase Timer)
DATA POLLING-Q7
The MX29F001T/B also features Data Polling as a
method to indicate to the host system that the Automatic Program or Erase algorithms are either in progress
or completed.
SET-UP AUTOMATIC PROGRAM COMMANDS
To initiate Automatic Program mode, A three-cycle command sequence is required. There are two "unlock" write
cycles. These are followed by writing the Automatic Program command A0H.
While the Automatic Programming algorithm is in operation, an attempt to read the device will produce the complement data of the data last written to Q7. Upon completion of the Automatic Program Algorithm an attempt to
read the device will produce the true data last written to
Q7. The Data Polling feature is valid after the rising edge
of the fourth WE pulse of the four write pulse sequences
for automatic program.
Once the Automatic Program command is initiated, the
next WE pulse causes a transition to an active programming operation. Addresses are latched on the falling
edge, and data are internally latched on the rising edge
of the WE pulse. The rising edge of WE also begins the
programming operation. The system does not require to
provide further controls or timings. The device will automatically provide an adequate internally generated program pulse and verify margin.
While the Automatic Erase algorithm is in operation, Q7
will read "0" until the erase operation is competed. Upon
completion of the erase operation, the data on Q7 will
read "1". The Data Polling feature is valid after the rising
edge of the sixth WE pulse of six write pulse sequences
for automatic chip/sector erase.
If the program operation was unsuccessful, the data on
Q5 is "1"(see Table 4), indicating the program operation
exceed internal timing limit. The automatic programming
operation is completed when the data read on Q6 stops
toggling for two consecutive read cycles and the data on
Q7 and Q6 are equivalent to data written to these two
bits, at which time the device returns to the Read mode
(no program verify command is required).
The Data Polling feature is active during Automatic Program/Erase algorithm or sector erase time-out.(see section Q3 Sector Erase Timer)
WRITE OPERATION STATUS
TOGGLE BIT-Q6
The MX29F001T/B features a "Toggle Bit" as a method
to indicate to the host system that the Auto Program/
Erase algorithms are either in progress or complete.
While the Automatic Program or Erase algorithm is in
progress, successive attempts to read data from the
device will result in Q6 toggling between one and zero.
Once the Automatic Program or Erase algorithm is completed, Q6 will stop toggling and valid data will be read.
The toggle bit is valid after the rising edge of the sixth
P/N: PM0515
REV. 2.6, DEC. 29, 2003
10
MX29F001T/B
Q5
Exceeded Timing Limits
Q3
Sector Erase Timer
Q5 will indicate if the program or erase time has exceeded
the specified limits(internal pulse count). Under these
conditions Q5 will produce a "1". This time-out condition
indicates that the program or erase cycle was not successfully completed. Data Polling and Toggle Bit are the
only operating functions of the device under this condition.
After the completion of the initial sector erase command
sequence the sector erase time-out will begin. Q3 will
remain low until the time-out is complete. Data Polling
and Toggle Bit are valid after the initial sector erase command sequence.
If Data Polling or the Toggle Bit indicates the device has
been written with a valid erase command, Q3 may be
used to determine if the sector erase timer window is
still open. If Q3 is high ("1") the internally controlled
erase cycle has begun; attempts to write subsequent
commands to the device will be ignored until the erase
operation is completed as indicated by Data Polling or
Toggle Bit. If Q3 is low ("0"), the device will accept additional sector erase commands. To insure the command
has been accepted, the system software should check
the status of Q3 prior to and following each subsequent
sector erase command. If Q3 were high on the second
status check, the command may not have been accepted.
If this time-out condition occurs during sector erase operation, it is specifies that a particular sector is bad and
it may not be reused. However, other sectors are still
functional and may be used for the program or erase
operation. The device must be reset to use other sectors. Write the Reset command sequence to the device,
and then execute program or erase command sequence.
This allows the system to continue to use the other active sectors in the device.
If this time-out condition occurs during the chip erase
operation, it specifies that the entire chip is bad or combination of sectors are bad.
DATA PROTECTION
If this time-out condition occurs during the byte programming operation, it specifies that the entire sector containing that byte is bad and this sector may not be reused, (other sectors are still functional and can be reused).
The MX29F001T/B is designed to offer protection against
accidental erasure or programming caused by spurious
system level signals that may exist during power transition. During power up the device automatically resets
the state machine in the Read mode. In addition, with its
control register architecture, alteration of the memory contents only occurs after successful completion of specific command sequences. The device also incorporates
several features to prevent inadvertent write cycles resulting from VCC power-up and power-down transition or
system noise.
The time-out condition may also appear if a user tries to
program a non blank location without erasing. In this
case the device locks out and never completes the Automatic Algorithm operation. Hence, the system never
reads a valid data on Q7 bit and Q6 never stops toggling.
Once the Device has exceeded timing limits, the Q5 bit
will indicate a "1". Please note that this is not a device
failure condition since the device was incorrectly used.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
11
MX29F001T/B
WRITE PULSE "GLITCH" PROTECTION
CHIP UNPROTECT WITH 12V SYSTEM
Noise pulses of less than 5ns(typical) on CE or WE will
not initiate a write cycle.
The MX29F001T/B also features the chip unprotect
mode, so that all sectors are unprotected after chip
unprotect completion to incorporate any changes in the
code.
LOGICAL INHIBIT
To activate this mode, the programming equipment must
force VID on control pin OE and address pin A9. The CE
pins must be set at VIL. Pins A6 must be set to VIH.(see
Table 2) Refer to chip unprotect algorithm and waveform for the chip unprotect algorithm. The unprotection
mechanism begins on the falling edge of the WE pulse
and is terminated with the rising edge of the same.
Writing is inhibited by holding any one of OE = VIL, CE =
VIH or WE = VIH. To initiate a write cycle CE and WE
must be a logical zero while OE is a logical one.
POWER SUPPLY DECOUPLING
It is also possible to determine if the chip is unprotected
in the system by writing the Read Silicon ID command.
Performing a read operation with A1=VIH, it will produce
00H at data outputs (Q0-Q7) for an unprotected sector. It
is noted that all sectors are unprotected after the chip
unprotect algorithm is completed.
In order to reduce power switching effect, each device
should have a 0.1uF ceramic capacitor connected between its VCC and GND. (Using a 10uF bulk capacitor
connected for high current condition is available if necessary.)
CHIP PROTECTION WITH 12V SYSTEM
CHIP PROTECTION WITHOUT 12V SYSTEM
The MX29F001T/B features hardware chip protection.
Which will disable both program and erase operations.
To activate this mode, the programming equipment must
force VID on address pin A9 and control pin OE, (suggest VID=12V) A6=VIL and CE=VIL.(see Table 2) Programming of the protection circuitry begins on the falling
edge of the WE pulse and is terminated with the rising
edge of the same. Please refer to chip protect algorithm
and waveform.
The MX29F001T/B also feature a hardware chip protection method in a system without 12V power supply. The
programming equipment do not need to supply 12 volts
to protect all sectors. The details are shown in chip protect algorithm and waveform.
CHIP UNPROTECT WITHOUT 12V SYSTEM
The MX29F001T/B also feature a hardware chip
unprotection method in a system without 12V power supply. The programming equipment do not need to supply
12 volts to unprotect all sectors. The details are shown
in chip unprotect algorithm and waveform.
To verify programming of the protection circuitry, the programming equipment must force VID on address pin A9
( with CE and OE at VIL and WE at VIH. When A1=1, it
will produce a logical "1" code at device output Q0 for
the protected status. Otherwise the device will produce
00H for the unprotected status. In this mode, the address, except for A1, are don't care. Address locations
with A1 = VIL are reserved to read manufacturer and
device codes.(Read Silicon ID)
POWER-UP SEQUENCE
The MX29F001T/B powers up in the Read only mode. In
addition, the memory contents may only be altered after
successful completion of the predefined command sequences.
It is also possible to determine if the chip is protected in
the system by writing a Read Silicon ID command. Performing a read operation with A1=VIH, it will produce a
logical "1" at Q0 for the protected status.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
12
MX29F001T/B
NOTICE:
Stresses greater than those listed under ABSOLUTE
MAXIMUM RATINGS may cause permanent damage
to the device. This is a stress rating only and
functional operational sections of this specification is
not implied. Exposure to absolute maximum rating
conditions for extended period may affect reliability.
ABSOLUTE MAXIMUM RATINGS
RATING
VALUE
Ambient Operating Temperature
0οC to 70οC
Storage Temperature
-65οC to 125οC
Applied Input Voltage
-0.5V to 7.0V
Applied Output Voltage
-0.5V to 7.0V
VCC to Ground Potential
-0.5V to 7.0V
A9 & OE
-0.5V to 13.5V
NOTICE:
Specifications contained within the following tables are
subject to change.
CAPACITANCE TA = 25oC, f = 1.0 MHz
SYMBOL
PARAMETER
CIN1
MIN.
TYP
MAX.
UNIT
CONDITIONS
Input Capacitance
8
pF
VIN = 0V
CIN2
Control Pin Capacitance
12
pF
VIN = 0V
COUT
Output Capacitance
12
pF
VOUT = 0V
READ OPERATION
DC CHARACTERISTICS VCC = 5V ± 10%
SYMBOL
PARAMETER
ILI
MIN.
TYP
MAX.
UNIT
Input Leakage Current
1
uA
VIN = GND to VCC
ILO
Output Leakage Current
10
uA
VOUT = GND to VCC
ISB1
Standby VCC current
1
mA
CE = VIH
5
uA
CE = VCC + 0.3V
30
mA
IOUT = 0mA, f=5MHz
50
mA
IOUT = 0mA, f=10MHz
ISB2
ICC1
1
Operating VCC current
ICC2
CONDITIONS
VIL
Input Low Voltage
-0.3(NOTE 1)
0.8
V
VIH
Input High Voltage
2.0
VCC + 0.3
V
VOL
Output Low Voltage
0.45
V
IOL = 2.1mA
VOH1
Output High Voltage(TTL)
2.4
V
IOH = -2mA
VOH2
Output High Voltage(CMOS)
VCC-0.4
V
IOH = -100uA
VCC=VCC MIN
NOTES:
1. VIL min. = -1.0V for pulse width is equal to or less than 50 ns.
VIL min. = -2.0V for pulse width is equal to or less than 20 ns.
2. VIH max. = VCC + 1.5V for pulse width is equal to or less than 20 ns
If VIH is over the specified maximum value, read operation cannot be guaranteed.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
13
MX29F001T/B
AC CHARACTERISTICS VCC = 5V ± 10%
SYMBOL PARAMETER
29F001T/B-90
29F001T/B-12
MIN.
MIN.
MAX.
MAX.
UNIT
CONDITIONS
tACC
Address to Output Delay
90
120
ns
CE=OE=VIL
tCE
CE to Output Delay
90
120
ns
OE=VIL
tOE
OE to Output Delay
40
50
ns
CE=VIL
tDF
OE High to Output Float (Note1)
0
30
ns
CE=VIL
tOH
Address to Output hold
0
ns
CE=OE=VIL
30
0
0
TEST CONDITIONS:
NOTE:
• Input pulse levels: 0.45V/2.4V
• Input rise and fall times: <10ns
• Output load: 1 TTL gate + 100pF (Including scope and
jig)
• Reference levels for measuring timing : 0.8V & 2.0V
1. tDF is defined as the time at which the output achieves
the open circuit condition and data is no longer driven.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
14
MX29F001T/B
READ TIMING WAVEFORMS
VIH
ADD Valid
A0~16
VIL
tCE
VIH
CE
VIL
WE
VIH
OE
VIH
tACC
VIL
DATA
Q0~7
tDF
tOE
VIL
VOH
tOH
HIGH Z
HIGH Z
DATA Valid
VOL
COMMAND PROGRAMMING/DATA PROGRAMMING/ERASE OPERATION
DC CHARACTERISTICS VCC = 5V ± 10%
SYMBOL
PARAMETER
ICC1 (Read)
Operating VCC Current
MIN.
TYP
MAX.
UNIT
CONDITIONS
30
mA
IOUT=0mA, f=5MHz
ICC2
50
mA
IOUT=0mA, F=10MHz
ICC3 (Program)
50
mA
In Programming
ICC4 (Erase)
50
mA
In Erase
mA
CE=VIH, Erase Suspended
ICCES
VCC Erase Suspend Current
2
NOTES:
1. VIL min. = -0.6V for pulse width < 20ns.
2. If VIH is over the specified maximum value, programming operation cannot be guaranteed.
3. ICCES is specified with the device de-selected. If the device is read during erase suspend mode, current draw is
the sum of ICCES and ICC1 or ICC2.
4. All current are in RMS unless otherwise noted.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
15
MX29F001T/B
AC CHARACTERISTICS VCC = 5V ± 10%
29F001T/B-90
MAX.
29F001T/B-12
SYMBOL PARAMETER
MIN.
MIN.
tOES
OE setup time
0
0
ns
tCWC
Command programming cycle
90
120
ns
tCEP
WE programming pulse width
45
50
ns
tCEPH1
WE programming pulse width High
20
20
ns
tCEPH2
WE programming pulse width High
20
20
ns
tAS
Address setup time
0
0
ns
tAH
Address hold time
45
50
ns
tDS
Data setup time
45
50
ns
tDH
Data hold time
0
0
ns
tCESC
CE setup time before command write
0
0
ns
tDF
Output disable time (Note 1)
tAETC
Total erase time in auto chip erase
3(TYP.)
24
tAETB
Total erase time in auto sector erase
1(TYP.)
tAVT
Total programming time in auto verify
7
tBAL
Sector address load time
100
100
us
tCH
CE Hold Time
0
0
ns
tCS
CE setup to WE going low
0
0
ns
tVLHT
Voltage Transition Time
4
4
us
tOESP
OE Setup Time to WE Active
4
4
us
tWPP
Write pulse width for chip protect
10
10
us
tWPP2
Write pulse width for chip unprotect
12
12
ms
40
MAX.
UNIT
40
ns
3(TYP.)
24
s
8
1(TYP.)
8
s
210
7
210
us
NOTES:
1. tDF defined as the time at which the output achieves the open circuit condition and data is no longer driven.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
16
MX29F001T/B
SWITCHING TEST CIRCUITS
DEVICE UNDER
TEST
1.6K ohm
+5V
CL
1.2K ohm
DIODES=IN3064
OR EQUIVALENT
CL=100pF Including jig capacitance
SWITCHING TEST WAVEFORMS
2.4 V
2.0V
2.0V
TEST POINTS
0.8V
0.8V
0.45 V
OUTPUT
INPUT
AC TESTING: Inputs are driven at 2.4V for a logic "1" and 0.45V for a logic "0".
Input pulse rise and fall times are < 10ns.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
17
MX29F001T/B
COMMAND WRITE TIMING WAVEFORM
VCC
5V
ADD
A0~16
VIH
WE
VIH
ADD Valid
VIL
tAH
tAS
VIL
tOES
tCEPH1
tCEP
tCWC
CE
VIH
VIL
tCS
OE
VIH
VIL
DATA
Q0-7
tCH
tDS
tDH
VIH
DIN
VIL
P/N: PM0515
REV. 2.6, DEC. 29, 2003
18
MX29F001T/B
AUTOMATIC PROGRAMMING TIMING WAVEFORM
One byte data is programmed. Verification in fast
algorithm and additional programming by external control
are not required because these operations are executed
automatically by internal control circuit. Programming
completion can be verified by DATA polling and toggle bit
checking after automatic verify starts. Device outputs
DATA during programming and DATA after programming
on Q7.(Q6 is for toggle bit; see toggle bit, DATA polling,
timing waveform)
AUTOMATIC PROGRAMMING TIMING WAVEFORM
Vcc 5V
A11~A16
A0~A10
ADD Valid
2AAH
555H
tAS
WE
ADD Valid
555H
tCWC
tAH
tCEPH1
tCESC
tAVT
CE
tCEP
OE
tDF
tDS tDH
Q0~Q2
Command In
Command In
Command In
DATA
Data In
DATA polling
,Q4(Note 1)
Q7
Command In
Command #AAH
Command In
Command In
Command #55H
Command #A0H
(Q0~Q7)
DATA
Data In
DATA
tOE
Notes:
(1). Q6:Toggle bit, Q5:Timing-limit bit, Q3: Time-out bit
P/N: PM0515
REV. 2.6, DEC. 29, 2003
19
MX29F001T/B
AUTOMATIC PROGRAMMING ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data A0H Address 555H
Write Program Data/Address
Toggle Bit Checking
Q6 not Toggled
NO
YES
Invalid
Command
NO
Verify Byte Ok
YES
NO
.
Q5 = 1
Auto Program Completed
YES
Reset
Auto Program Exceed
Timing Limit
P/N: PM0515
REV. 2.6, DEC. 29, 2003
20
MX29F001T/B
TOGGLE BIT ALGORITHM
START
Read Q7~Q0
Read Q7~Q0
(Note 1)
NO
Toggle Bit Q6
=Toggle?
YES
NO
Q5=1?
YES
(Note 1,2)
Read Q7~Q0 Twice
NO
Toggle Bit Q6=
Toggle?
YES
Program/Erase Operation Not
Complete, Write Reset Command
Program/Erase Operation Complete
Notes:
1.Read toggle bit Q6 twice to determine whether or not it is toggle. See text.
2.Recheck toggle bit Q6 because it may stop toggling as Q5 changes to "1". See text.
P/N: PM0515
REV. 2.6, DEC. 29, 2003
21
MX29F001T/B
AUTOMATIC CHIP ERASE TIMING WAVEFORM
All data in chip are erased. External erase verification is
not required because data is erased automatically by
internal control circuit. Erasure completion can be verified by DATA polling and toggle bit checking after auto
matic erase starts. Device outputs 0 during erasure and
1 after erasure 0n Q7.(Q6 is for toggle bit; see toggle bit,
DATA polling, timing waveform)
AUTOMATIC CHIP ERASE TIMING WAVEFORM
Vcc 5V
A11~A16
A0~A10
2AAH
555H
555H
555H
tAS
WE
2AAH
555H
tCWC
tAH
tCEPH1
tAETC
CE
tCEP
OE
tDS tDH
Q0,Q1,
Command In
Command In
Command In
Command In
Command In
Command In
Q4(Note 1)
Q7
DATA polling
Command In
Command In
Command In
Command In
Command In
Command In
Command #AAH
Command #55H
Command #80H
Command #AAH
Command #55H
Command #10H
(Q0~Q7)
Notes:
(1). Q6:Toggle bit, Q5:Timing-limit bit, Q3: Time-out bit, Q2: Toggle bit
P/N: PM0515
REV. 2.6, DEC. 29, 2003
22
MX29F001T/B
AUTOMATIC CHIP ERASE ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 80H Address 555H
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 10H Address 555H
Toggle Bit Checking
Q6 not Toggled
NO
YES
Invalid
Command
NO
DATA Polling
Q7 = 1
YES
NO
.
Q5 = 1
Auto Chip Erase Completed
YES
Reset
Auto Chip Erase Exceed
Timing Limit
P/N: PM0515
REV. 2.6, DEC. 29, 2003
23
MX29F001T/B
AUTOMATIC SECTOR ERASE TIMING WAVEFORM
checking after automatic erase starts. Device outputs 0
during erasure and 1 after erasure on Q7.(Q6 is for toggle
bit; see toggle bit, DATA polling, timing waveform)
Sector data indicated by A13 to A16 are erased. External
erase verify is not required because data are erased
automatically by internal control circuit. Erasure completion can be verified by DATA polling and toggle bit
AUTOMATIC SECTOR ERASE TIMING WAVEFORM
Vcc 5V
Sector
Address0
A13~A16
A0~A10
555H
2AAH
555H
555H
Sector
Address1
Sector
Addressn
2AAH
tAS
tCWC
tAH
WE
tCEPH1
tBAL
tAETB
CE
tCEP
OE
tDS tDH
Q0,Q1,
Command
In
Command
In
Command
In
Command
In
Command
In
Command
In
Command
In
Command
In
Q4(Note 1)
Q7
DATA polling
Command
In
Command
In
Command
In
Command
In
Command
In
Command
In
Command #AAH Command #55H Command #80H Command #AAH Command #55H Command #30H
(Q0~Q7)
Command
In
Command #30H
Command
In
Command #30H
Notes:
(1). Q6:Toggle bit, Q5:Timing-limit bit, Q3: Time-out bit, Q2: Toggle bit
P/N: PM0515
REV. 2.6, DEC. 29, 2003
24
MX29F001T/B
AUTOMATIC SECTOR ERASE ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 80H Address 555H
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 30H Sector Address
Toggle Bit Checking
Q6 Toggled ?
NO
Invalid Command
YES
Load Other Sector Addrss If Necessary
(Load Other Sector Address)
NO
Last Sector
to Erase
YES
Time-out Bit
Checking Q3=1 ?
NO
YES
Toggle Bit Checking
Q6 not Toggled
NO
YES
NO
.
Q5 = 1
DATA Polling
Q7 = 1
YES
Reset
Auto Sector Erase Completed
Auto Sector Erase
Exceed Timing
P/N: PM0515
REV. 2.6, DEC. 29, 2003
25
MX29F001T/B
ERASE SUSPEND/ERASE RESUME FLOWCHART
START
Write Data B0H
NO
Toggle Bit checking Q6
not toggled
YES
Read Array or
Program
Reading or
Programming End
NO
YES
Write Data 30H
Continue Erase
Another
Erase Suspend ?
NO
.
YES
P/N: PM0515
REV. 2.6, DEC. 29, 2003
26
MX29F001T/B
TIMING WAVEFORM FOR CHIP PROTECTION FOR SYSTEM WITH 12V
A1
A6
12V
5V
A9
tVLHT
Verify
12V
5V
OE
tVLHT
tVLHT
tWPP 1
WE
tOESP
CE
Data
01H
F0H
tOE
P/N: PM0515
REV. 2.6, DEC. 29, 2003
27
MX29F001T/B
TIMING WAVEFORM FOR CHIP UNPROTECTION FOR SYSTEM WITH 12V
A1
12V
5V
A9
tVLHT
A6
Verify
12V
5V
OE
tVLHT
tVLHT
tWPP 2
WE
tOESP
CE
Data
00H
F0H
tOE
P/N: PM0515
REV. 2.6, DEC. 29, 2003
28
MX29F001T/B
CHIP PROTECTION ALGORITHM FOR SYSTEM WITH 12V
START
PLSCNT=1
OE=VID,A9=VID,CE=VIL
A6=VIL
Activate WE Pulse
Time Out 10us
Device Failed
Set WE=VIH, CE=OE=VIL
A9 should remain VID
Read from Sector
Addr=SA, A1=1
No
PLSCNT=32?
No
Data=01H?
Yes
Remove VID from A9
Write Reset Command
Device Failed
Chip Protection
Complete
P/N: PM0515
REV. 2.6, DEC. 29, 2003
29
MX29F001T/B
CHIP UNPROTECTION ALGORITHM FOR SYSTEM WITH 12V
START
PLSCNT=1
Set OE=A9=VID
CE=VIL,A6=1
Activate WE Pulse
Time Out 12ms
Increment
PLSCNT
Set OE=CE=VIL
A9=VID,A1=1
Read Data from Device
No
Data=00H?
No
PLSCNT=1000?
Yes
Yes
Remove VID from A9
Write Reset Command
Device Failed
Chip Unprotect
Complete
P/N: PM0515
REV. 2.6, DEC. 29, 2003
30
MX29F001T/B
TIMING WAVEFORM FOR CHIP PROTECTION FOR SYSTEM WITHOUT 12V
A1
A6
Toggle bit polling
Verify
5V
OE
tCEP
WE
* See the following Note!
CE
Data
Don't care
(Note 2)
01H
F0H
tOE
Note: 1. Must issue "unlock for sector protect/unprotect" command
before chip protection for a system without 12V provided.
2. Except F0H
P/N: PM0515
REV. 2.6, DEC. 29, 2003
31
MX29F001T/B
TIMING WAVEFORM FOR CHIP UNPROTECTION FOR SYSTEM WITHOUT 12V
A1
A6
Toggle bit polling
Verify
5V
OE
tCEP
WE
* See the following Note!
CE
Data
Don't care
(Note 2)
00H
F0H
tOE
Note: 1. Must issue "unlock for sector protect/unprotect" command
before chip unprotection for a system without 12V provided.
2. Except F0H
P/N: PM0515
REV. 2.6, DEC. 29, 2003
32
MX29F001T/B
CHIP PROTECTION ALGORITHM FOR SYSTEM WITHOUT 12V
START
PLSCNT=1
Write "unlock for chip protect/unprotect"
Command(Table1)
OE=VIH,A9=VIH
CE=VIL,A6=VIL
Activate WE Pulse to start
Data don't care
Toggle bit checking
DQ6 not Toggled
No
.
Yes
Increment PLSCNT
Set CE=OE=VIL
A9=VIH
Raed from Sector
Addr=SA, A1=1
No
PLSCNT=32?
No
Data=01H?
Yes
Device Failed
Yes
Write Reset Command
Chip Protection
Complete
P/N: PM0515
REV. 2.6, DEC. 29, 2003
33
MX29F001T/B
CHIP UNPROTECTION ALGORITHM FOR SYSTEM WITHOUT 12V
START
PLSCNT=1
Write "unlock for chip protect/unprotect"
Command (Table 1)
Set OE=A9=VIH
CE=VIL,A6=1
Activate WE Pulse to start
Data don't care
No
Toggle bit checking
DQ6 not Toggled
Increment
PLSCNT
Yes
Set OE=CE=VIL
A9=VIH,A1=1
Read Data from Device
No
No
Data=00H?
Yes
PLSCNT=1000?
Yes
Device Failed
Write Reset Command
Chip Unprotect
Complete
P/N: PM0515
REV. 2.6, DEC. 29, 2003
34
MX29F001T/B
ID CODE READ TIMING WAVEFORM
VCC
5V
VID
ADD
VIH
A9
VIL
tACC
tACC
A1
VIH
VIL
ADD
A2-A8
A10-A16
CE
VIH
VIL
VIH
VIL
WE
VIH
tCE
VIL
OE
VIH
tOE
VIL
tDF
tOH
tOH
VIH
DATA
Q0-Q7
DATA OUT
DATA OUT
VIL
18H/19H
C2H
P/N: PM0515
REV. 2.6, DEC. 29, 2003
35
MX29F001T/B
ERASE AND PROGRAMMING PERFORMANCE (1)
LIMITS
PARAMETER
TYP.(2)
MAX.(3)
UNITS
Sector Erase Time
1
8
s
Chip Erase Time
3
24
s
Byte Programming Time
7
210
us
Chip Programming Time
3.5
10.5
sec
Erase/Program Cycles
Note:
MIN.
100,000
Cycles
1.Not 100% Tested, Excludes external system level over head.
2.Typical values measured at 25° C, 5V.
3.Maximum values measured at 25° C, 4.5V.
LATCH-UP CHARACTERISTICS
MIN.
MAX.
Input Voltage with respect to GND on all pins except I/O pins
-1.0V
13.5V
Input Voltage with respect to GND on all I/O pins
-1.0V
Vcc + 1.0V
-100mA
+100mA
Current
Includes all pins except Vcc. Test conditions: Vcc = 5.0V, one pin at a time.
DATA RETENTION
PARAMETER
Data Retention Time
P/N: PM0515
MIN.
UNIT
20
Years
REV. 2.6, DEC. 29, 2003
36
MX29F001T/B
ORDERING INFORMATION
PLASTIC PACKAGE (Top Boot Sector as an sample For Bottom Boot Sector ones,MX29F001Txx will
change to MX29F001Bxx)
PART NO.
ACCESS TIME
OPERATING CURRENT
STANDBY CURRENT
PACKAGE
(ns)
MAX.(mA)
MAX.(uA)
MX29F001TQC-90
90
30
5
32 Pin PLCC
MX29F001TQC-12
120
30
5
32 Pin PLCC
MX29F001TTC-90
90
30
5
32 Pin TSOP
(Normal Type)
MX29F001TTC-12
120
30
5
32 Pin TSOP
(Normal Type)
MX29F001TPC-90
90
30
5
32 Pin PDIP
MX29F001TPC-12
120
30
5
32 Pin PDIP
P/N: PM0515
REV. 2.6, DEC. 29, 2003
37
MX29F001T/B
PACKAGE INFORMATION
P/N: PM0515
REV. 2.6, DEC. 29, 2003
38
MX29F001T/B
P/N: PM0515
REV. 2.6, DEC. 29, 2003
39
MX29F001T/B
P/N: PM0515
REV. 2.6, DEC. 29, 2003
40
MX29F001T/B
REVISION HISTORY
Revision
Description
Page
Date
2.0
1. To remove "Advanced Information" data sheet marking and
contain information on products in full production
2.The modification summary from Revision 0.0 to Revision 1.0:
2-1.Program/erase cycle times:10K cycles-->100K cycles
2-2.To add data retention 20 years
2-3.To remove A9 from the timing waveform of protection/
unprotection without 12V
2-4.Multi-sector erase time out:80ms-->30us
2-5.tBAL:80us-->100us
To modify "Package Information"
To corrected typing error
1. Add industrial grade spec
2. Modify maximum value measurement temperature from 25° C to 85° C
1. Remove industrial grade spec
1. To modify Package Information
1. Removed 55ns/70ns specification
P1
DEC/21/1999
2.1
2.2
2.3
2.4
2.5
2.6
P/N: PM0515
P1,38
P1,38
P32,33
P8
P16,17
P39~41
JUN/14/2001
All
JUL/01/2002
P13,38
JUL/09/2002
P37
P13,37,38 AUG/12/2002
P39~41
NOV/20/2002
P1,13~18,37 DEC/29/2003
REV. 2.6, DEC. 29, 2003
41
MX29F001T/B
MACRONIX INTERNATIONAL CO., LTD.
Headquarters:
TEL:+886-3-578-6688
FAX:+886-3-563-2888
Europe Office :
TEL:+32-2-456-8020
FAX:+32-2-456-8021
Hong Kong Office :
TEL:+86-755-834-335-79
FAX:+86-755-834-380-78
Japan Office :
Kawasaki Office :
TEL:+81-44-246-9100
FAX:+81-44-246-9105
Osaka Office :
TEL:+81-6-4807-5460
FAX:+81-6-4807-5461
Singapore Office :
TEL:+65-6346-5505
FAX:+65-6348-8096
Taipei Office :
TEL:+886-2-2509-3300
FAX:+886-2-2509-2200
MACRONIX AMERICA, INC.
TEL:+1-408-262-8887
FAX:+1-408-262-8810
http : //www.macronix.com
MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice.
Similar pages