CHEMI-CON APSK2R5E561ME08S Conductive polymer aluminum solid capacitor Datasheet

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
TM
NPCAP
Radial Lead
PSK
-
Series
PSK
・Super low ESR, high ripple current capability
・Downsized from PSE series (φ6.3×8L to φ5×8L)
・Long life (20,000 hours at 105℃)
・Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
・RoHS Compliant
・Halogen Free
Downsized
PSE P56
◆SPECIFICATIONS
Items
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current*Note
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max.Impedance Ratio)
Endurance
Bias Humidity Test
Surge Voltage Test
Failure Rate
Characteristics
-55 to +105℃
2.5 to 6.3 Vdc
±20% (M)
Rated voltage(V)×1.15
500µA max.
(at 20℃, 120Hz)
(at 105℃)
(at 20℃ after 2 minutes)
0.10 max.
(at 20℃, 120Hz)
Z(-25℃)/Z(+20℃)≦1.15
Z(-55℃)/Z(+20℃)≦1.25
(at 100kHz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 20,000 hours
at 105℃.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦150% of the initial specified value
ESR
≦150% of the initial specified value
Leakage current
≦The initial specified value
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃,
90 to 95% RH for 1,000 hours.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦The initial specified value
ESR
≦The initial specified value
Leakage current
≦The initial specified value
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds
through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds.
Appearance
No significant damage
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
≦The initial specified value
ESR
≦The initial specified value
Leakage current
≦The initial specified value
0.5% per 1,000 hours maximum (Confidence level 60% at 105℃)
*Note : If any doubt arises, measure the leakage current after the following voltage treatment.
Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃.
◆DIMENSIONS [mm]
Code : E
F±0.5
● Terminal
φD'
φd
Coated Case
L'
15min.
4min.
Size code
E08
φD
5.0
φd
0.5(Note2)
F
2.0
φD'
φD+0.5max.
L'
L+1.0max.
Note2 : 0.45 for rated vollage 2.5V
◆MARKING
EX) 2.5V560µF
K6D6
560
2.5V
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
52
CAT. No. E1001Q
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
TM
NPCAP
Radial Lead
PSKSeries
-
◆PART NUMBERING SYSTEM
1
2
3
4
A PSK
5
6
7
8
9
10
11
12
13
14
15
16
17
18
E AA 5 6 1 M E 0 8 S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 560µF:561)
Lead forming.Taping code
Terminal code
Voltage code (ex. 2.5V:2R5, 6.3V:6R3)
Series code
Category
Please refer to "Product code guide (conductive polymer type)"
◆STANDARD RATINGS
WV
(Vdc)
2.5
4
6.3
Cap
(µF)
Case size
φD×L (mm)
ESR
(mΩ max./20℃, 100k to 300kHz)
Rated ripple current
(mArms/105℃, 100kHz)
Part No.
220
330
470
560
330
270
330
5 ×8
5× 8
5× 8
5× 8
5×8
5 ×8
5×8
7
7
7
7
8
10
8
4,350
4,350
4,350
4,350
4,050
3,700
4,050
APSK2R5E□□221ME08S
APSK2R5E□□331ME08S
APSK2R5E□□471ME08S
APSK2R5E□□561ME08S
APSK4R0E□□331ME08S
APSK6R3E□□271ME08S
APSK6R3E□□331ME08S
□□ : Enter the appropriate lead forming or taping code.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
53
CAT. No. E1001Q
Similar pages