Intersil EL1529IL-T13 Dual channel differential dsl line driver for globespan co chipset Datasheet

EL1529
®
Data Sheet
February 11, 2005
Dual Channel Differential DSL Line Driver
for Globespan CO Chipsets
The EL1529 is to be used with Globespan's G7566-850 CO
chipset for high performance long reach and high speed
applications, including ADSL2, ADSL2+, G.Span, and
G.Span+.
The EL1529 is an integral part of the signal chain. The driver
has been optimized for flat gain response and reduced
harmonic distortion and noise in the bands of interest to
improve the overall signal to noise in the system.
These drivers achieve a total harmonic distortion (THD)
measurement of typically -70dB @ 1.1MHz, while
consuming typically 5mA per DSL channel of total supply
current. This supply current can be set using a resistor on
the IADJ pin. Two other pins (C0 & C1) can also be used to
adjust supply current to one of four pre-set modes (full-IS,
3/4-IS, 1/2-IS, and full power-down). The EL1529 operates
on ±5V to ±12V supplies and retains its bandwidth and
linearity over the complete supply range.
The device is supplied in the small footprint (4x5mm) 24-pin
QFN package and is specified for operation over the full
-40°C to +85°C temperature range.
Pinout
20 VOUTA
21 NC
22 VS-
23 C0AB
24 C1AB
EL1529
(24-PIN QFN)
TOP VIEW
VINA+ 1
19 VINA-
VINB+ 2
18 VINB17 VOUTB
GND 3
THERMAL
PAD
IADJ 4
16 VOUTC
13 VOUTD
1
Features
• 450mA output drive capability
• 44.1VP-P differential output drive into 100Ω
• -85dBc THD @ 1MHz 2VP-P
• High slew rate of 500V/µs
• Bandwidth - 46MHz
• Current control pins
• Channel separation
- 80dB @ 500kHz
- 75dB @ 1MHz
• Pb-free available (RoHS compliant)
Applications
• ADSL line drivers for Globespan G7566-850 CO chipsets
Ordering Information
PART
NUMBER
PACKAGE
TAPE &
REEL
PKG. DWG. #
EL1529IL
24-Pin QFN
-
MDP0046
EL1529IL-T7
24-Pin QFN
7”
MDP0046
EL1529IL-T13
24-Pin QFN
13”
MDP0046
EL1529ILZ
(See Note)
24-Pin QFN
(Pb-Free)
-
MDP0046
EL1529ILZ-T7
(See Note)
24-Pin QFN
(Pb-Free)
7”
MDP0046
EL1529ILZ-T13
(See Note)
24-Pin QFN
(Pb-Free)
13”
MDP0046
NOTE: Intersil Pb-free products employ special Pb-free material sets;
molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with
both SnPb and Pb-free soldering operations. Intersil Pb-free products
are MSL classified at Pb-free peak reflow temperatures that meet or
exceed the Pb-free requirements of IPC/JEDEC J STD-020.
NC 12
VIND+ 7
NC 11
14 VIND-
VS+ 10
VINC+ 6
C0CD 9
15 VINC-
C1CD 8
NC 5
FN7406.1
Get Full Datasheet
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-352-6832 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2004, 2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
EL1529
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
2
FN7406.1
February 11, 2005
Similar pages