Semtech ECLAMP2455K Esd/emi protection for sim card Datasheet

EClamp2455K
ESD/EMI Protection
for SIM Card
PRELIMINARY
PROTECTION PRODUCTS - EMIClampTM
Description
Features
The EClampTM2455K is combination EMI filter and line
termination device with integrated TVS diodes for use on
SIM Card interfaces on cellular phones and other portable electronics. This state-of-the-art device utilizes
solid-state silicon-avalanche technology for superior
clamping performance and DC electrical characteristics.
‹ Bidirectional EMI/RFI filter with integrated TVS
for ESD protection
‹ ESD protection to IEC 61000-4-2 (ESD) Level 4,
‹
‹
‹
‹
‹
The device consists of three circuits that include series
impedance matching resistors for proper termination of
the SIM card interface. Termination resistor value of
100 Ohms is included on the RST and Data lines and 47
Ohms on the CLK line. TVS diodes are also included on
each line for ESD protection in excess of ±15kV (air
discharge) and ±8kV (contact discharge) per IEC 610004-2, level 4. An additional TVS diode connection is
included for protection of the voltage (Vcc) bus.
±15kV (air), ±8kV (contact)
TVS working voltage: 5V
Termination Resistors: 100 Ohms & 47 Ohms
Capacitance: 20pF (Typical at VR = 0V)
Protection and filtering for four lines
Solid-state technology
Mechanical Characteristics
‹
‹
‹
‹
‹
‹
‹
The EClamp2455K is in a 8-pin, RoHS/WEEE compliant, SLP1713P8 package. It measures 1.7 x 1.3 x
0.50mm. The leads are spaced at a pitch of 0.4mm
and are finished with lead-free NiPdAu. The small
package makes it ideal for use in portable electronics
such as cell phones and digital still cameras.
SLP1713P8 8-pin package
RoHS/WEEE Compliant
Nominal Dimensions: 1.7 x 1.3 x 0.50 mm
Lead Pitch: 0.4mm
Lead finish: NiPdAu
Marking: Marking Code
Packaging: Tape and Reel per EIA 481
Applications
‹ SIM Card
‹ Cell Phone
‹ PDAs and Smartphones
Package Configuration
Pin Configuration
1.70
1 2
RST Out
1
8
CLK Out
CLK In
Gnd
0.40 BSC
Data In
Data Out
NC
1.30
RST In
4
5
Vcc
0.50
Pin Identification and Configuration
(Top Side View)
Revision 03/27/2007
8 Pin SLP package (Bottom Side View)
Nominal Dimensions in mm
1
www.semtech.com
EClamp2455K
PRELIMINARY
PROTECTION PRODUCTS
Pin Identification and Configuration
Pin
Symbol
Identification
1, 8
RST
Reset input/output with
termination resistor
2, 7
C LK
Clock input/output with
termination resistor
3, 6
Data
Data input/output with
termination resistor
4
NC
No Connect
5
Vcc
Power Supply ESD
Protection
Center
tab
GND
Ground connection
8
7
6
5
3
4
Gnd
1
2
Pin Configuration (Top View)
Schematics & Component Values
Vcc
100 Ω
RST IN
RST OUT
47 Ω
CLK IN
CLK OUT
100 Ω
Data OUT
Data IN
GND
© 2007 Semtech Corp.
2
www.semtech.com
EClamp2455K
PRELIMINARY
PROTECTION PRODUCTS
Maximum Ratings
R ating
Symbol
Value
Units
VESD
+/- 18
+/- 12
kV
Junction Temp erature
TJ
125
o
Op erating Temp erature
Top
-40 to +85
o
Storage Temp erature
TSTG
-55 to +150
o
ESD p er IEC 61000-4-2 (Air)
ESD p er IEC 61000-4-2 (Contact)
C
C
C
Electrical Characteristics (T=25oC)
P ar am et er
S y m b ol
Con d i t i on s
Mi n i mu m
Ty p i c a l
M ax i m u m
Units
5
V
10
V
0.5
μA
T VS Reverse Stand-Off Voltage
VRWM
T VS Reverse Breakdown Voltage
V BR
It = 1mA
IR
VRWM = 5.0V
Reset Series Resistors
RRST
Each Line
85
100
115
Ohms
Clk Series Resistors
R
CLK
Each Line
40
47
55
Ohms
Data Series Resistors
RDATA
Each Line
85
100
115
Ohms
Cin
Inp ut to Gnd,
Each Line
VR = 0V, f = 1MHz
16
20
24
pF
T VS Reverse Leakage Current
Total Cap acitance
© 2007 Semtech Corp.
3
6
8
www.semtech.com
EClamp2455K
PRELIMINARY
PROTECTION PRODUCTS
Typical Characteristics
Typical Insertion Loss S21 (Pin 2 to 7)
CH1 S21
LOG
Typical Insertion Loss S21 (Pin 1 to 8 and Pin 3 to 6)
6 dB / REF 0 dB
CH1 S21
LOG
6 dB / REF 0 dB
1: -6.4316 dB
307.466 MHz
1: -8.9909 dB
294.402 MHz
2: -14.641 dB
900 MHz
0 dB
3: -23.808dB
1.8 GHz
-6 dB
1
-12 dB
-18 dB
1
-12 dB
4: -30.765 dB
2.5 GHz
-18 dB
5: -30.455 dB
2.7 GHz
-24 dB
3: -28.966dB
1.8 GHz
-6 dB
4: -28.845 dB
2.5 GHz
2
2: -19.003 dB
900 MHz
0 dB
5: -30.974 dB
2.7 GHz
2
-24 dB
3
5
-30 dB
5
-30 dB
4
3
4
-36 dB
-36 dB
-42 dB
-42 dB
-48 dB
1
MHz
10
MHz
100
MHz
-48 dB
1
3
GHz GHz
STOP 3000. 000000 MHz
START. 030 MHz
1
MHz
10
MHz
1
3
GHz GHz
STOP 3000. 000000 MHz
START. 030 MHz
ESD Clamping (+8kV Contact)
100
MHz
ESD Clamping (-8kV Contact)
Note: Data is taken with a 10x attenuator
Note: Data is taken with a 10x attenuator
Analog Crosstalk (Each Line)
Normalized Capacitance vs. Reverse Voltage
CH1 S21
1.1
LOG
20 dB /REF 0 dB
1
0.9
CJ(VR) / CJ(VR=0)
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
f = 1 MHz
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
Reverse Voltage - VR (V)
© 2007 Semtech Corp.
START. 030 MHz
4
STOP 3000. 000000 MHz
www.semtech.com
EClamp2455K
PRELIMINARY
PROTECTION PRODUCTS
Device Connection
Figure 1 - Pin Identification and Configuration
(Top Side View)
The EClamp2455K designed with ease of layout in
mind. The package has flow through design which
allows the designer to route the signals straight in and
out between the SIM port connector and the SIM
controller. The device is in a 8-pin SLP package.
Electrical connection is made to the 8 pins located at
the bottom of the device. A center tab serves as the
ground connection. Pin connections are noted in
Figure 1. All path lengths should be kept as short as
possible to minimize the effects of parasitic inductance
in the board traces.
RST Out
1
8
CLK Out
CLK In
Gnd
Data In
Data Out
NC
RST In
4
5
Vcc
SIM Controller
SIM Card
Connector
RST OUT
1
8
CLK OUT
RST In
CLK IN
Gnd
DATA OUT
4
DATA IN
5
Vcc
Reset
Clock
Data I/O
5V/3.3V/1.8V
EClamp2455K
EClamp2455P
Figure 2 - SIM Protection
© 2007 Semtech Corp.
5
www.semtech.com
EClamp2455K
PRELIMINARY
PROTECTION PRODUCTS
Applications Information - Spice Model
EClamp2455K Spice Model & Parameters
Vcc
100 Ω
RST IN
RST OUT
47 Ω
CLK IN
CLK OUT
100 Ω
Data OUT
Data IN
GND
EClamp2455K Spice Model
Note: All TVS shown in the circuit use D1 Parameters
Table 1 - EClamp2455K Spice Parameters
© 2007 Semtech Corp.
Parameter
Unit
D1 (T VS)
IS
Amp
2E-15
BV
Volt
7.5
VJ
Volt
0.775
RS
Ohm
1.05
IB V
A mp
1E-3
CJO
Farad
9E-12
TT
sec
2.541E-9
M
--
0.246
N
--
1.1
EG
eV
1.11
6
www.semtech.com
EClamp2455K
PRELIMINARY
PROTECTION PRODUCTS
Outline Drawing - SLP1713P8
A
D
B
DIM
PIN 1
INDICATOR
(LASER MARK)
A
A1
A2
b
D
D1
E
E1
e
L
N
aaa
bbb
E
A
SEATING
PLANE
aaa C
A2
C
A1
DIMENSIONS
INCHES
MILLIMETERS
MIN NOM MAX MIN NOM MAX
.018 .020 .022
.000 .001 .002
(.005)
.006 .008 .010
.065 .067 .070
.047 .051 .055
.049 .051 .054
.008 .012 .016
.016 BSC
.008 .010 .012
8
.003
.004
0.45 0.50 0.55
0.00 0.02 0.05
(0.13)
0.15 0.20 0.25
1.65 1.70 1.775
1.20 1.30 1.40
1.25 1.30 1.375
0.20 0.30 0.40
0.40 BSC
0.20 0.25 0.30
8
0.08
0.10
D1
1
2
LxN
E/2
E1
N
bxN
e/2
bbb
C A B
e
D/2
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS.
Land Pattern - SLP1713P8
P
X
Z
G
DIM
C
G
H
K
P
X
Y
Z
H (C)
Y
DIMENSIONS
INCHES
MILLIMETERS
(.050)
(1.27)
.027
0.69
.012
0.30
.055
1.40
.016
0.40
.008
0.20
.023
0.58
.073
1.85
K
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY.
CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR
COMPANY'S MANUFACTURING GUIDELINES ARE MET.
3. THERMAL VIAS IN THE LAND PATTERN OF THE EXPOSED PAD
SHALL BE CONNECTED TO A SYSTEM GROUND PLANE.
FAILURE TO DO SO MAY COMPROMISE THE THERMAL AND/OR
FUNCTIONAL PERFORMANCE OF THE DEVICE.
© 2007 Semtech Corp.
7
www.semtech.com
EClamp2455K
PRELIMINARY
PROTECTION PRODUCTS
Marking
Ordering Information
2455K
PIN 1
INDICATOR
XXXX
Part Number
Qty per
Reel
R eel Size
EClamp 2455K.TCT
3000
7 Inch
This is a lead-free RoHS/WEEE Compliant Device
EMIClamp and EClamp are marks of Semtech Corporation
XXXX = Date Code
Tape and Reel Specification
Pin 1 Location
User Direction of feed
Device Orientation in Tape
A0
1.51 +/-0.05 mm
B0
K0
1.91 +/-0.05 mm
0.66 +/-0.05 mm
Tape
Width
B, (Max)
D
D1
8 mm
4.2 mm
(.165)
1.5 + 0.1 mm
- 0.0 mm
(0.59 +.005
- .000)
0.8 mm
±0.05
(.031)
E
1.750±.10
mm
(.069±.004)
F
K
(MAX)
P
P0
P2
T(MAX)
W
3.5±0.05
mm
(.138±.002)
2.4 mm
(.094)
4.0±0.1
mm
(.157±.004)
4.0±0.1
mm
(.157±.004)
2.0±0.05mm
(.079±.002)
0.4 mm
(.016)
8.0 mm
+ 0.3 mm
- 0.1 mm
(.312±.012)
Contact Information
Semtech Corporation
Protection Products Division
200 Flynn Rd., Camarillo, CA 93012
Phone: (805)498-2111 FAX (805)498-3804
© 2007 Semtech Corp.
8
www.semtech.com
Similar pages