AD ADM6819ARJZ-REEL7 Fet drive simple sequencer Datasheet

FET Drive Simple Sequencers®
ADM6819/ADM6820
FEATURES
FUNCTIONAL BLOCK DIAGRAM
VCC1
Q1
VCC2
VCC2 OUT
VCC2
VCC1
CHARGE
PUMP
Multivoltage systems
Dual voltage microprocessors/FPGAs/ASICs/DSPs
Network processors
Telecom and datacom systems
PC/server applications
VFET
UVLO
R1
LOGIC
SETV
R2
FET
DRIVER
GATE
0.618V
TIMER
ADM6819/
ADM6820
APPLICATIONS
VCC1
0.618V
GND
EN (ADM6819) - DIGITAL/ANALOG
SETD (ADM6820)
05133-001
Single chip enables power supply sequencing of two
supplies
On-board charge pump fully enhances N-channel FET
Adjustable primary supply monitor to 0.618 V
Delay from primary supply to secondary supply enabled
Fixed 300 ms delay (ADM6819)
Capacitor adjustable delay (ADM6820)
Logic/analog driven enable input (ADM6819)
−40°C to +85°C operating range
Packaged in small 6-lead SOT-23 package
Pin-to-pin compatibility with MAX6819/MAX6820
Figure 1.
GENERAL DESCRIPTION
The ADM6819 and ADM6820 are simple power supply sequencers
with FET drive capability for enhancing N-channel MOSFETs.
These devices can monitor a primary supply voltage and
enable/disable an external N-channel FET for a secondary
supply. The ADM6819 has the ability to monitor two supplies.
When more than two voltages require sequencing, multiple
ADM6819/ADM6820 devices can be cascaded to achieve this.
The devices operate over a supply range of 2.95 V to 5.5 V.
The ADM6819 features an enable (EN) pin that is fed to the
input of an additional comparator and reference circuit. This
pin can be used as a digital enable or a secondary power good
comparator to monitor a second supply and enables the GATE
only if both supplies are valid. When both inputs of the internal
comparators are above the threshold, a fixed 300 ms timeout
occurs before the GATE is driven high and the secondary
supply is enabled.
An internal comparator monitors the primary supply using the
VSET pin. The input to this comparator is externally set via a
resistor divider from the primary supply. When the voltage at
the VSET pin rises above the comparator threshold, an internal
charge pump on the GATE output enhances the secondary
supply FET.
The ADM6820 has only one comparator that is on the SETV
pin. It also features a timeout period that is adjustable via a
single external capacitor on the SETD pin.
The ADM6819/ADM6820 are packaged in small 6-lead SOT-23
packages.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2006 Analog Devices, Inc. All rights reserved.
ADM6819/ADM6820
TABLE OF CONTENTS
Features .............................................................................................. 1
Pin Configuration and Function Descriptions..............................7
Applications....................................................................................... 1
Typical Performance Characteristics ..............................................8
Functional Block Diagram .............................................................. 1
Theory of Operation ...................................................................... 10
General Description ......................................................................... 1
SETV Pin ..................................................................................... 10
Revision History ............................................................................... 2
EN Pin.......................................................................................... 10
Specifications..................................................................................... 3
GATE Pin .................................................................................... 10
Timing Diagrams.............................................................................. 4
SETD Pin ..................................................................................... 10
Absolute Maximum Ratings............................................................ 6
Outline Dimensions ....................................................................... 11
Thermal Characteristics .............................................................. 6
Ordering Guide .......................................................................... 11
ESD Caution.................................................................................. 6
REVISION HISTORY
7/06—Rev. 0: Initial Version
Rev. 0 | Page 2 of 12
ADM6819/ADM6820
SPECIFICATIONS
VCC1 or VCC2 = 2.95 V to 5.5 V, TA = −40°C to +85°C, unless otherwise noted. Typical values are at TA = 25°C. 1
Table 1.
Parameter
VCC1, VCC2 PINS
Operating Voltage Range, VCC1 or VCC2
VCC1 or VCC2 Supply Current, ICC
VCC1 or VCC2 Disable Mode Current
VCC1 or VCC2 Slew Rate 2
Undervoltage Lockout, VUVLO
SETV PIN
SETV Threshold, VTH
SETV Input Current2
SETV Threshold Hysteresis
SETV to GATE Delay, tDELAY
SETD PIN
SETD Ramp Current, ISETD
SETD Voltage, VSETD
GATE PIN
GATE Turn-On Time, tON
GATE Turn-Off Time, tOFF
GATE Voltage, VGATE
ENABLE PIN
EN Input Voltage Low, VIL
EN Input Voltage High, VIH
Min
Typ
0.9
350
250
6
1.2/tDELAY
2.4
Max
Units
5.5
500
V
μA
μA
V/s
V/s
V
Conditions
VCC1 or VCC2 must be > 2.95 V
VCC1 or VCC2 must be > 2.95 V
VCC1 = VCC2 = 3.3 V
VCC1 = VCC2 = 3.3 V, EN = GND
ADM6819
ADM6820 3
VCC falling
2.525
2.65
0.634
100
240
0.618
10
−1
300
350
V
nA
%
ms
300
400
1.295
500
500
1.326
730
600
1.357
nA
nA
V
TA = 25°C
0.5
1.5
30
5.5
5.0
9.4
8.6
10
ms
μs
V
V
V
V
CGATE = 1500 pF, VCC2 = 3.3 V, VGATE = 7.8 V
CGATE = 1500 pF, VCC2 = 3.3 V, VGATE = 0.5 V
With respect to VCCx, RGATE > 50 MΩ to VCCx 4
With respect to VCCx, RGATE > 5 MΩ to VCCx4
With respect to VCCx, RGATE > 50 MΩ to VCCx 5
With respect to VCCx, RGATE > 5 MΩ to VCCx5
V
V
VCC1 or VCC2 must be > 2.95 V
VCC1 or VCC2 must be > 2.95 V
0.602
4.5
4.0
8.9
8.2
6.0
6
9.9
9.1
0.4
2.0
1
100% production tested at TA = +25°C. Specifications over temperature limit are guaranteed by design.
Guaranteed by design, not production tested.
3
tDELAY (s) = 2.65 × 106 × CSET.
4
Highest supply pin is represented by VCCx = 2.95 V.
5
Highest supply pin is represented by VCCx = 5.5 V.
2
Rev. 0 | Page 3 of 12
VSETV rising, enables GATE
VSETV falling, disables GATE
VSETV > VTH ; VEN > VTH (ADM6819)
ADM6820
ADM6819/ADM6820
TIMING DIAGRAMS
VCC1
VCC1
Q1
VCC2
VCC2 OUT
VCC1
VCC2
CHARGE
PUMP
VFET
UVLO
R1
LOGIC
SETV
R3
FET
DRIVER
GATE
0.618V
R2
R4
ADM6819
GND
0.618V
05133-014
EN
Figure 2. ADM6819 Solution for Validating Two Supplies Before Sequencing
0.618V
VSETV
tON
VCC2 + 5.5V (typ)
90%
10%
VGATE
10%
tOFF
05133-015
tDELAY
(ADM6819 = 300ms,
ADM6820 = ADJ)
Figure 3. ADM6819/ADM6820 Timing Diagram Using SETV for Sequencing
VSETV
VEN
0.618V
0.618V
tON
VCC2 + 5.5V (typ)
90%
10%
tOFF
tDELAY
(300ms)
Figure 4. ADM6819 Timing Diagram Using EN and SETV for Sequencing
Rev. 0 | Page 4 of 12
05133-016
10%
VGATE
ADM6819/ADM6820
VIN = 5V
VOUT = 5V
Q1
VIN = 3.3V
Q2
VIN = 3.0V
VOUT = 3.3V
VOUT = 3.0V
VCC2
VCC2
GATE
GATE
VCC1
ADM6819/
ADM6820
SETV
R3
EN/SETD
SETV
GND
R2
ADM6819/
ADM6820
EN/SETD
GND
R4
Figure 5. ADM6819/ADM6820 Solution for Sequencing Three Supply Rails
Rev. 0 | Page 5 of 12
05133-017
R1
VCC1
ADM6819/ADM6820
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
VCC1, VCC2
SETV, SETD, EN
GATE
Storage Temperature
Operating Temperature Range
Lead Temperature (Soldering 10 sec)
Junction Temperature
Rating
−0.3 V to +6.0 V
−0.3 V to +30 V
−0.3 V to (VCCx + 11 V)
−65°C to +150°C
−40°C to +85°C
300°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL CHARACTERISTICS
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
Table 3. Thermal Resistance
Package Type
6-Lead SOT-23
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 6 of 12
θJA
169.5
Unit
°C/W
ADM6819/ADM6820
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
6
VCC2
VCC1 1
ADM6819
TOP VIEW
5 GATE
(Not to Scale)
SETV 3
4
EN
GND 2
05133-002
GND 2
6
VCC2
ADM6820
SETV 3
Figure 6. ADM6819 Pin Configuration
TOP VIEW
5 GATE
(Not to Scale)
4
SETD
05133-003
VCC1 1
Figure 7. ADM6820 Pin Configuration
Table 4. Pin Function Descriptions
Pin Number
ADM6819 ADM6820
1
1
Mnemonic
VCC1
2
3
2
3
GND
SETV
4
–
EN
–
4
SETD
5
5
GATE
6
6
VCC2
Description
Supply Voltage 1. Either VCC1 or VCC2 must be greater than the UVLO to enable external
FET Drive.
Chip Ground Pin.
Sequenced Threshold Set. Connect to an external resistor divider to set the VCC1
threshold that enables GATE turn-on. The internal reference is 0.618 V.
Active-High Enable. GATE drive is enabled tDELAY after EN is driven high. GATE drive is
immediately disabled when EN is driven low. Connect this pin to the higher of VCC1 or
VCC2 if not used. EN is internally identical to SETV (0.618 V threshold) and, therefore, can
be used as a second supply monitor, enabling two supplies to be validated before
sequencing begins.
GATE Delay Set Input. Connect an external capacitor from SETD to GND to adjust the
delay from SETV > VTH to GATE turn-on. tDELAY(s) = 2.652 × 106 × CSET(F).
GATE Drive Output. GATE drives an external N-channel FET to connect VCC2 to the load.
GATE drive enables tDELAY after SETV exceeds VTH and ENABLE is driven high. GATE drive is
immediately disabled when SETV drops below VTH or ENABLE is driven low. When
enabled, an internal charge pump drives GATE above VCCX to fully enhance the external
N-channel FET.
Supply Voltage 2. Either VCC1 or VCC2 must be greater than the UVLO to enable the
external FET Drive.
Rev. 0 | Page 7 of 12
ADM6819/ADM6820
TYPICAL PERFORMANCE CHARACTERISTICS
0.50
0.65
0.45
0.64
0.35
SUPPLY CURRENT (mA)
0.40
ICC1 (VCC1 = 5V, VCC2 = 3.3V)
0.30
0.25
0.20
0.63
0.62
0.61
0.60
0.59
0.15
0.10
–50
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
0.58
–50
–25
0
25
50
75
100
125
150
TEMPERATURE (°C)
Figure 8. Supply Current vs. Temperature
05133-007
VEN = 2V
VSETV = 2V
05133-004
SUPPLY CURRENT (mA)
ICC2 (VCC1 = 3.3V, VCC2 = 5V)
Figure 11. Supply Current vs. Temperature
0.50
VCC1 = 0V
VEN = 2V
VSETV = 2V
14
0.40
12
0.35
10
0.25
8
0.20
6
0.15
4
0.10
VCC1 = 3.3V
VEN = 2V
VSETV = VCC2
2
0.05
0
1
2
3
4
5
6
7
VCC2 (V)
05133-005
0
0
0
1
4
5
6
Figure 12. VGATE vs. VCC2
0.50
14
VCC1 = 3.3V
VEN = 2V
VSETV = 2V
12
0.40
0.35
VGATE (V)
10
0.30
0.25
0.20
8
6
4
0.10
VCC1 = 0V
VEN = 2V
VSETV = 1V
2
0.05
0
0
0
1
2
3
4
VCC2 (V)
5
6
7
0
1
2
3
4
VCC2 (V)
Figure 13. VGATE vs. VCC2
Figure 10. ICC2 vs. VCC2
Rev. 0 | Page 8 of 12
5
6
05133-009
0.15
05133-006
ICC2 (mA)
3
VCC2 (V)
Figure 9. ICC2 vs. VCC2
0.45
2
05133-008
0.30
VGATE (V)
ICC2 (mA)
0.45
ADM6819/ADM6820
14
12
VSETV
VGATE (V)
10
8
VGATE
5V/DIV
6
VCC1 = 3.3V
VEN = 2V
VSETV = 1V
CLOAD = 1500pF
0
0
1
2
3
4
6
5
VCC2 (V)
05133-010
2
20µs/DIV
Figure 14. VGATE vs. VCC2
05133-018
4
Figure 16. Gate Turn-Off Time
340
330
320
300
290
280
270
250
240
–50
CLOAD = 1500pF
–25
0
25
50
75
100
TEMPERATURE (°C)
125
150
1ms/DIV
Figure 15. tDELAY vs. Temperature
Figure 17. Gate Turn-On Time
Rev. 0 | Page 9 of 12
05133-019
VGATE
5V/DIV
260
05133-011
tDELAY (ms)
310
ADM6819/ADM6820
THEORY OF OPERATION
The ADM6819/ADM6820 provide local voltage sequencing in
multisupply systems. Figure 18 and Figure 19 show typical
application diagrams for these devices.
VIN = 3.3V
VOUT = 3.3V
Q1
VIN = 3.0V
VOUT = 3.0V
VCC2
GATE
VCC1
R1
ADM6819
ON
EN
SETV
SETV PIN
The ADM6819/ADM6820 enable a supply after a monitored
supply voltage exceeds a programmed threshold. This threshold
is programmed by a R1/R2 resistor divider on the SETV pin.
Once the voltage on SETV exceeds the 0.618 V threshold, the
FET switches on after the delay timer expires. On the
ADM6820, this delay is programmable using a capacitor on the
SETD pin. On the ADM6819, this delay is fixed at 300 ms and
the EN pin must be valid high to begin the timer. The required
turn-on voltage is calculated by the following equation:
R1 = R2 ((VTRIP/VTH) – 1)
OFF
GND
05133-012
R2
Figure 18. ADM6819 Applications Diagram
VIN = 3.3V
Q1
VIN = 3.0V
VOUT = 3.3V
VOUT = 3.0V
VCC2
EN PIN
GATE
VCC1
R1
ADM6820
SETD
SETV
CSET
05133-013
GND
R2
where:
VTRIP is the minimum turn-on voltage at the supply being
monitored.
VTH = 0.618 V.
High value resistors can be used because the SETV input
current is typically 10 nA.
Figure 19. ADM6820 Applications Diagram
When the primary supply is above the desired threshold, the
ADM6819/ADM6820 are designed to control the N-channel
FET in the secondary power path to enable the secondary
supply. The GATE pin is held low while both VCC1 and VCC2 are
below the undervoltage threshold, ensuring that the FET is held
off. When VCC1 or VCC2 is above UVLO and the primary supply
is above the desired level dictated by the resistor divider to the
VSET pin, the external FET is driven on after the delay has
expired. An internal charge pump enhances the external FET. A
FET with a low drain-source resistance and low VTH should be
chosen to reduce voltage drop across the drain-source when the
FET is fully enhanced. Either supply may act as the primary
source if VCC1 or VCC2 is greater that 2.95 V. A decoupling
capacitor of typically 100 nF should be used on whichever VCC
is the main supply.
The ADM6819 has an enable (EN) pin connected to the input
of a second comparator, which is identical to that on the VSET
pin. EN can be used as a digital input provided the signal VOL is
below 0.6 V. Alternatively, the enable input can be used to
validate a second supply. The fixed 300 ms timer does not begin
counting until both SETV and EN are above the threshold. As a
result, the output is not enabled until this timer has expired.
GATE PIN
The internal charge pump is capable of driving the gate of an
N-channel MOSFET with no external capacitors. This ensures
that the MOSFET is enhanced to provide a minimum voltage
drop across the MOSFET, thus reducing the voltage drop across
the FET. This charge pump is designed to drive the high impedance capacitive load of a MOSFET gate input. The GATE pin
should not be resistively loaded because it reduces the gate drive
capability. During undervoltage lockout, GATE is held to GND.
SETD PIN
The ADM6820 features a capacitor adjustable sequencing delay.
A capacitor connected to the SETD pin determines the length
of the sequencing delay. The sequencing delay can be calculated
by the following equation:
tDELAY (s) = 2.652 × 106 × CSET
The ADM6819 has a fixed 300 ms delay.
Rev. 0 | Page 10 of 12
ADM6819/ADM6820
OUTLINE DIMENSIONS
2.90 BSC
6
5
4
2.80 BSC
1.60 BSC
1
2
3
PIN 1
INDICATOR
0.95 BSC
1.90
BSC
1.30
1.15
0.90
1.45 MAX
0.50
0.30
0.15 MAX
0.22
0.08
SEATING
PLANE
10°
4°
0°
0.60
0.45
0.30
COMPLIANT TO JEDEC STANDARDS MO-178-AB
Figure 20. 6-Lead Small Outline Transistor Package [SOT-23]
(RJ-6)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADM6819ARJZ-REEL7 1
ADM6820ARJZ-REEL71
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
6-Lead Small Outline Transistor Package [SOT-23]
6-Lead Small Outline Transistor Package [SOT-23]
Z = Pb-free part.
Rev. 0 | Page 11 of 12
Package Option
RJ-6
RJ-6
Branding
M2R
M2S
ADM6819/ADM6820
NOTES
©2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05113-0-7/06(0)
Rev. 0 | Page 12 of 12
Similar pages