Maxim MXD1210CSA Nonvolatile ram controller Datasheet

19-0154; Rev 1; 3/96
Nonvolatile RAM Controller
Applications
µP Systems
____________________________Features
♦ Battery Backup
♦ Memory Write Protection
♦ 230µA Operating-Mode Quiescent Current
♦ 2nA Backup-Mode Quiescent Current
♦ Battery Freshness Seal
♦ Optional Redundant Battery
♦ Low Forward-Voltage Drop on VCC Supply Switch
♦ 5% or 10% Power-Fail Detection Options
Computers
♦ Tests Battery Condition During Power-Up
Embedded Systems
♦ 8-Pin SO Available
_________________Pin Configurations
______________Ordering Information
PART
TOP VIEW
V CCO 1
8
V CCI
VBATT1 2
7
VBATT2
6
CEO
5
CE
TOL 3
MXD1210
GND 4
TEMP. RANGE
PIN-PACKAGE
MXD1210CPA
0°C to +70°C
8 Plastic DIP
MXD1210CSA
MXD1210CWE
MXD1210C/D
MXD1210EPA
MXD1210ESA
MXD1210EWE
MXD1210MJA
0°C to +70°C
0°C to +70°C
0°C to +70°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-55°C to +125°C
8 SO
16 Wide SO
Dice*
8 Plastic DIP
8 SO
16 Wide SO
8 CERDIP
*Contact factory for dice specifications.
DIP/SO
__________Typical Operating Circuit
N.C. 1
16 N.C.
V CCO 2
15 V CCI
N.C. 3
14 N.C.
VBATT1 4
MXD1210
13 VBATT2
N.C. 5
12 N.C.
TOL 6
11 CEO
N.C. 7
10 N.C.
GND 8
9 CE
+5V
VCCI
8
VCCO
1
2
VBATT1
VBATT2
MXD1210 7
CE
5
FROM
DECODER
4
VCC
CMOS
RAM
6
CE
3
Wide SO
GND
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800
MXD1210
_______________General Description
The MXD1210 nonvolatile RAM controller is a very lowpower CMOS circuit that converts standard (volatile)
CMOS RAM into nonvolatile memory. It also continually
monitors the power supply to provide RAM write protection when power to the RAM is in a marginal (out-oftolerance) condition. When the power supply begins to
fail, the RAM is write protected, and the device switches to battery-backup mode.
MXD1210
Nonvolatile RAM Controller
ABSOLUTE MAXIMUM RATINGS
Continuous Power Dissipation (TA = +70°C)
8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) ....727mW
8-Pin SO (derate 5.88mW/°C above +70°C).................471mW
16-Pin Wide SO (derate 9.52mW/°C above +70°C)......762mW
8-Pin CERDIP (derate 8.00mW/°C above +70°C).........640mW
Operating Temperature Ranges
MXD1210C_ _ ..................................................... 0°C to +70°C
MXD1210E_ _ .................................................. -40°C to +85°C
MXD1210MJA ................................................ -55°C to +125°C
Storage Temperature Range ........................... -65°C to +150°C
Lead Temperature (soldering, 10sec) ............................ +300°C
VCCI to GND ................................................................-0.3V, +7V
VBATT1 to GND.......................................................... -0.3V, +7V
VBATT2 to GND.......................................................... -0.3V, +7V
VCCO to GND..................................................... -0.3V, VS + 0.3V
(VS = greater of VCCI, VBATT1, VBATT2)
Digital Input and Output Voltages to GND............. 0.3V, VCCI + 0.3V
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
RECOMMENDED OPERATING CONDITIONS
Supply Voltage
Input High Voltage
VIH
Input Low Voltage
VIL
Battery Voltage (Note 1)
TOL = GND
4.75
5.50
TOL = VCCO
4.50
5.50
VCCI
VBATT1
VBATT2
V
2.2
1 or 2 batteries
V
2.0
0.8
V
4.0
V
ELECTRICAL CHARACTERISTICS
(VCCI = +4.75V to +5.5V, TOL = GND; or VCCI = +4.5V to +5.5V, TOL = VCCO; TA = TMIN to TMAX; unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
0.23
0.5
mA
NORMAL SUPPLY MODE, TOL = VCCO
Supply Current
Output Supply Voltage
VCCO
VCCO, CEO open,
VBATT1 = VBATT2 = 3V
ICCO1 = 80mA
(Note 2)
MXD1210C
VCCI - 0.20
MXD1210E
VCCI - 0.21
MXD1210M
MXD1210C
MXD1210E
MXD1210M
VCCI - 0.25
V
Input Leakage Current
IIL
80
75
65
±1.0
Output Leakage Current
IOL
±1.0
High-Level Output Voltage
Low-Level Output Voltage
VOH
VOL
Output Supply Current
VCCI Trip Point
2
ICCI
ICCO
VCCTP
VCCI - VCCO ≤ 0.2V
(Note 2)
IOH = -1mA
IOL = 4mA
TOL = GND
TOL = VCCO
0.23
0.23
2.4
4.50
4.25
_______________________________________________________________________________________
0.4
4.74
4.49
mA
µA
µA
V
V
V
Nonvolatile RAM Controller
ELECTRICAL CHARACTERISTICS
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
2
100
nA
5
µA
300
µA
MXD1210
(VCCI < VBATT; positive edge rate at VBATT1, VBATT2 > 0.1V/µs, TA = TMIN to TMAX; unless otherwise noted.)
BATTERY-BACKUP MODE
Quiescent Current (Note 1)
IBATT
VCCO, CEO open MXD1210C/E
VCCI = 0V
MXD1210M
Output Supply Current (Notes 3, 4)
ICCO2
VBATT - VCCO ≤ 0.2V
CEO Output Voltage
VO
Output open
VBATT - 0.2
V
ELECTRICAL CHARACTERISTICS
(TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
CIN
5
pF
COUT
7
pF
INPUT/OUTPUT CAPACITANCE (Note 5)
Input Capacitance
Output Capacitance
VCC POWER TIMING CHARACTERISTICS
(VCCI = +4.75V to +5.5V, TOL = GND; or VCCI = +4.5V to +5.5V, TOL = VCCO; TA = TMIN to TMAX; unless otherwise noted.)
PARAMETER
SYMBOL
CE Propagation Delay
tPD
CE High to Power-Fail (Note 5)
CONDITIONS
RL = 1kΩ,
CL = 50pF
MIN
TYP
MAX
MXD1210C
5
10
20
MXD1210E
5
10
22
MXD1210M
5
10
25
tPF
0
UNITS
ns
ns
TIMING CHARACTERISTICS
(VCCI < +4.75V to +5.5V, TOL = GND; or VCCI < +4.5V , TOL = VCCO; TA = TMIN to TMAX; unless otherwise noted.)
PARAMETER
Recovery at Power-Up
VCC Slew-Rate Power-Down
SYMBOL
CONDITIONS
tREC
MIN
TYP
MAX
UNITS
2
5
20
ms
tF
To out-of-tolerance condition
300
tFB
Tolerance to battery power
10
VCC Slew-Rate Power-Up
tR
CE Pulse Width (Note 6)
tCE
µs
0
µs
1.5
µs
Note 1: Only one battery input is required. Unused battery inputs must be grounded.
Note 2: ICCO1 is the maximum average load current the MXD1210 can supply to the memories.
Note 3: ICCO2 is the maximum average load current the MXD1210 can supply to the memories in battery-backup mode.
Note 4: CEO can sustain leakage current only in battery-backup mode.
Note 5: Guaranteed by design.
Note 6: tCE max must be met to ensure data integrity on power loss.
_______________________________________________________________________________________
3
MXD1210
Nonvolatile RAM Controller
______________________________________________________________Pin Description
PIN
NAME
FUNCTION
8-PIN DIP/SO
16-PIN WIDE SO
1
2
VCCO
2
4
VBATT1
3
6
TOL
Tolerance select pin
4
8
GND
Ground
5
9
CE
6
11
CEO
7
13
VBATT2
8
15
VCCI
5V power supply to chip
–
1, 3, 5, 7
10, 12, 14, 16
N.C.
No connect, not internally connected
Backed-up supply to RAM
Battery 1 positive connection
Chip-enable input
Chip-enable output
Battery 2 positive connection
VCCI
P
VCCO
VBATT1
P
P
FRESHNESSSEAL MODE
VBATT2
N
P
GND
BATTERY
SELECT
MXD1210
GND
BATTERY
TEST
VOLTAGE LEVEL
DETECTION
CE
CEO
CONTROL
TOL
Figure 1. Block Diagram
4
_______________________________________________________________________________________
CEO
Nonvolatile RAM Controller
Main Functions
The MXD1210 executes five main functions to perform
reliable RAM operation and battery backup (see
Typical Operating Circuit and Figure 1):
1. RAM Power-Supply Switch: The switch directs
power to the RAM from the incoming supply or
from the selected battery, whichever is at the
greater voltage. The switch control uses the same
criterion to direct power to MXD1210 internal
circuitry.
2. Power-Failure Detection: The write-protection function is enabled when a power failure is detected.
The power-failure detection range depends on the
state of the TOL pin as follows:
CONDITION
VCCTP RANGE (V)
TOL = GND
4.75 to 4.50
TOL = VCCO
4.50 to 4.25
Power-failure detection is independent of the batterybackup function and precedes it sequentially as the
power-supply voltage drops during a typical power
failure.
3. Write Protection: This holds the chip-enable output
(CEO) to within 0.2V of VCCI or of the selected battery, whichever is greater. If the chip-enable input
(CE )is low (active) when power failure is detected,
then CEO is held low until CE is brought high, at
which time CEO is gated high for the duration of
the power failure. The preceding sequence completes the current RD/WR cycle, preventing data
corruption if the RAM access is a WR cycle.
4. Battery Redundancy: A second battery is optional.
When two batteries are connected, the stronger
battery is selected to provide RAM backup and to
power the MXD1210. The battery-selection circuitry
remains active while in the battery-backup mode,
selecting the stronger battery and isolating the
weaker one. The battery-selection activity is transparent to the user and the system. If only one battery is connected, the second battery input should
be grounded.
5. Battery-Status Warning: This notifies the system
when the stronger of the two batteries measures
≤ 2.0V. Each time the MXD1210 is repowered
(VCCI > VCCTP) after detecting a power failure, the
battery voltage is measured. If the battery in use is
low, following the MXD1210 recovery period, the
device issues a warning to the system by inhibiting the second memory cycle. The sequence is as
follows:
First access: read memory location n, loc(n) = x
Second access: write memory location n,
loc (n) = complement (x)
Third access: read memory location n, loc (n) = ?
If the third access (read) is complement (x), then the
battery is good; otherwise, the battery is not good.
Return to loc(n) = x following the test sequence.
Freshness-Seal Mode
The freshness-seal mode relates to battery longevity
during storage rather than directly to battery backup.
This mode is activated when the first battery is connected, and is defeated when the voltage at V CCI first
exceeds VCCTP. In the freshness-seal mode, both batteries are isolated from the system; that is, no current is
drained from either battery, and the RAM is not powered by either battery. This means that batteries can be
installed and the system can be held in inventory without battery discharge. The positive edge rate at
VBATT1 and VBATT2 should exceed 0.1V/µs. The batteries will maintain their full shelf-life while installed in
the system.
Battery Backup
The Typical Operating Circuit shows the MXD1210 connected in order to write protect the RAM when VCC is
less than 4.75V, and to provide battery backup to the
supply.
_______________________________________________________________________________________
5
MXD1210
______________ Detailed Description
MXD1210
Nonvolatile RAM Controller
tCE
CE
CE
VIH
VIH
VIL
VBATT -O.2V
VIH
tPF
tPD
VBATT -0.2V
tCE
CEO
CEO
VIH
VIL
tPD
tREC
tF
4.75V
4.5V
VCCI
VCCI
4.75V
4.5V
4.25V
4.25V
3V
tR
tFB
Figure 2. Power-Up Timing Diagram
6
Figure 3. Power-Down Timing Diagram
_______________________________________________________________________________________
Nonvolatile RAM Controller
V CCI
MXD1210
__________________Chip Topography
VBATT2
V CCO
VBATT1
0.121"
(3.073mm)
CEO
TOL
CE
GND
0.080"
(2.032mm)
TRANSISTOR COUNT: 1436;
LEAVE SUBSTRATE UNCONNECTED.
_______________________________________________________________________________________
7
MXD1210
Nonvolatile RAM Controller
________________________________________________________Package Information
DIM
E
A
A1
B
C
D
E
e
H
h
L
α
H
INCHES
MAX
MIN
0.069
0.053
0.010
0.004
0.019
0.014
0.010
0.007
0.197
0.189
0.157
0.150
0.050 BSC
0.244
0.228
0.020
0.010
0.050
0.016
8˚
0˚
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.35
0.49
0.19
0.25
4.80
5.00
3.80
4.00
1.27 BSC
5.80
6.20
0.25
0.50
0.40
1.27
0˚
8˚
21-325A
h x 45˚
D
α
A
8-PIN PLASTIC
SMALL-OUTLINE
PACKAGE
0.127mm
0.004in.
e
A1
C
L
B
DIM
D1
A
A1
A2
A3
B
B1
C
D
D1
E
E1
e
eA
eB
L
α
E
E1
D
A3
A
A2
L
A1
INCHES
MAX
MIN
0.200
–
–
0.015
0.175
0.125
0.080
0.055
0.022
0.016
0.065
0.050
0.012
0.008
0.390
0.348
0.035
0.005
0.325
0.300
0.280
0.240
0.100 BSC
0.300 BSC
0.400
–
0.150
0.115
15˚
0˚
MILLIMETERS
MIN
MAX
–
5.08
0.38
–
3.18
4.45
1.40
2.03
0.41
0.56
1.27
1.65
0.20
0.30
8.84
9.91
0.13
0.89
7.62
8.26
6.10
7.11
2.54 BSC
7.62 BSC
–
10.16
2.92
3.81
0˚
15˚
21-324A
α
C
e
B1
eA
B
8-PIN PLASTIC
DUAL-IN-LINE
PACKAGE
eB
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1996 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Similar pages