SAMSUNG KM718V987

KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
Document Title
256Kx36 & 512Kx18-Bit Synchronous Burst SRAM
Revision History
Rev. No.
History
Draft Date
Remark
0.0
Initial draft
April. 10 . 1998
Preliminary
0.1
Change DC Characteristics.
ISB value from 60mA to 90mA at -8
ISB value from 50mA to 80mA at -9
ISB value from 40mA to 70mA at -10
ISB1 value from 10mA to 30mA
ISB2 value from 10mA to 30mA
Aug. 31. 1998
Preliminary
0.2
1. Changed tCD from 8.0ns to 8.5ns at -8
2. Changed tCYC from 13.0ns to 12.0ns at -10
3. Changed DC condition at Icc and parameters
ICC ; from 300mA to 350mA at -8,
from 260mA to 300mA at -9,
from 220mA to 260mA at -10,
ISB ; from 90mA to 130mA at -8,
from 80mA to 120mA at -9,
from 70mA to 110mA at -10,
Sep. 09. 1998
Preliminary
0.3
1. ADD 119BGA(7x17 Ball Grid Array Package) .
2. ADD x32 organization.
Oct. 15. 1998
Preliminary
0.4
Add VDDQ Supply voltage( 2.5V )
Dec. 10. 1998
Preliminary
0.5
Changed VOL Max value from 0.2V to 0.4V at 2.5V I/O.
Dec. 23. 1998
Preliminary
1.0
1. Final Spec Release.
2. Remove x32 organization.
Jan. 29. 1999
Final
2.0
1. Remove VDDQ supply voltage(2.5V)
Feb. 25. 1999
Final
3.0
1. Changed ICC from 350mA to 330mA at -8.
2. Add bin -7. (tCD 7.5ns).
Mar. 30. 1999
Final
4.0
1. Add VDDQ supply voltage(2.5V)
May. 13. 1999
Final
The attached data sheets are prepared and approved by SAMSUNG Electronics. SAMSUNG Electronics CO., LTD. reserve the right to change the
specifications. SAMSUNG Electronics will evaluate and reply to your requests and questions on the parameters of this device. If you have any questions, please contact the SAMSUNG branch office near your office, call or contact Headquarters.
-1-
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
256Kx36 & 512Kx18-Bit Synchronous Burst SRAM
FEATURES
GENERAL DESCRIPTION
• Synchronous Operation.
• On-Chip Address Counter.
• Self-Timed Write Cycle.
• On-Chip Address and Control Registers.
• 3.3V+0.165V/-0.165V Power Supply.
• I/O Supply Voltage 3.3V+0.165V/-0.165V for 3.3V I/O
or 2.5V+0.4V/-0.125V for 2.5V I/O
• 5V Tolerant Inputs Except I/O Pins.
• Byte Writable Function.
• Global Write Enable Controls a full bus-width write.
• Power Down State via ZZ Signal.
• LBO Pin allows a choice of either a interleaved burst or a linear burst.
• Three Chip Enables for simple depth expansion with No Data
Contention only for TQFP.
• Asynchronous Output Enable Control.
• ADSP, ADSC, ADV Burst Control Pins.
• TTL-Level Three-State Output.
• 100-TQFP-1420A /119BGA(7x17 Ball Grid Array Package)
The KM736V887 and KM718V987 are 9,437,184-bit Synchronous Static Random Access Memory designed for high performance second level cache of Pentium and Power PC based
System.
It is organized as 256K(512K) words of 36(18) bits and integrates address and control registers, a 2-bit burst address
counter and added some new functions for high performance
cache RAM applications; GW, BW, LBO, ZZ. Write cycles are
internally self-timed and synchronous.
Full bus-width write is done by GW, and each byte write is performed by the combination of WEx and BW when GW is high.
And with CS1 high, ADSP is blocked to control signals.
Burst cycle can be initiated with either the address status processor(ADSP) or address status cache controller(ADSC)
inputs. Subsequent burst addresses are generated internally in
the system′s burst sequence and are controlled by the burst
address advance(ADV) input.
LBO pin is DC operated and determines burst sequence(linear
or interleaved).
ZZ pin controls Power Down State and reduces Stand-by current regardless of CLK.
The KM736V887 and KM718V987 are fabricated using SAMSUNG′s high performance CMOS technology and is available
in a 100pin TQFP and 119BGA package. Multiple power and
ground pins are utilized to minimize ground bounce.
FAST ACCESS TIMES
PARAMETER
Symbol -7
-8
-9
-10 Unit
10
12
12
Cycle Time
tCYC
8.5
Clock Access Time
tCD
7.5 8.5 9.0 10.0 ns
ns
Output Enable Access Time
tOE
3.5 3.5 3.5 3.5
ns
LOGIC BLOCK DIAGRAM
CLK
LBO
BURST CONTROL
LOGIC
CONTROL
REGISTER
ADV
ADSC
A′0~A′1
256Kx36 , 512Kx18
MEMORY
ARRAY
A0~A1
A0~A17
or A0~A18
ADSP
ADDRESS
REGISTER
A2~A17
or A2~A18
DATA-IN
REGISTER
CONTROL
REGISTER
CS1
CS2
CS2
GW
BW
BURST
ADDRESS
COUNTER
WEx
(x=a,b,c,d or a,b)
OUTPUT
BUFFER
CONTROL
LOGIC
OE
ZZ
DQa0 ~ DQd7 or DQa0 ~ DQb7
DQPa ~ DQPd
DQPa,DQPb
-2-
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
ADV
A8
A9
82
81
49
50
A16
ADSP
A15
ADSC
84
83
OE
85
48
BW
86
A14
GW
87
47
CLK
88
A13
VSS
89
46
VDD
90
A12
CS2
91
45
WEa
92
A11
WEb
93
44
WEc
94
A10
WEd
95
43
CS2
96
A17
CS1
97
42
A7
98
N.C.
A6
99
100 Pin TQFP
(20mm x 14mm)
31
32
33
34
35
36
37
38
39
40
41
A4
A3
A2
A1
A0
N.C.
N.C.
VSS
VDD
KM736V887(256Kx36)
A5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
LBO
DQPc
DQc0
DQc1
VDDQ
VSSQ
DQc2
DQc3
DQc4
DQc5
VSSQ
VDDQ
DQc6
DQc7
N.C.
VDD
N.C.
VSS
DQd0
DQd1
VDDQ
VSSQ
DQd2
DQd3
DQd4
DQd5
VSSQ
VDDQ
DQd6
DQd7
DQPd
100
PIN CONFIGURATION(TOP VIEW)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
DQPb
DQb7
DQb6
VDDQ
VSSQ
DQb5
DQb4
DQb3
DQb2
VSSQ
VDDQ
DQb1
DQb0
VSS
N.C.
VDD
ZZ
DQa7
DQa6
VDDQ
VSSQ
DQa5
DQa4
DQa3
DQa2
VSSQ
VDDQ
DQa1
DQa0
DQPa
PIN
SYMBOL
A0 - A17
PIN NAME
TQFP PIN NO.
Address Inputs
32,33,34,35,36,37,43
44,45,46,47,48,49,50
81,82,99,100
ADV
Burst Address Advance
83
ADSP
Address Status Processor 84
ADSC
Address Status Controller 85
CLK
Clock
89
CS1
Chip Select
98
CS2
Chip Select
97
CS2
Chip Select
92
WEx(x=a,b,c,d) Byte Write Inputs
93,94,95,96
OE
Output Enable
86
GW
Global Write Enable
88
BW
Byte Write Enable
87
ZZ
Power Down Input
64
LBO
Burst Mode Control
31
SYMBOL
PIN NAME
TQFP PIN NO.
VDD
VSS
N.C.
Power Supply(+3.3V)
Ground
No Connect
15,41,65,91
17,40,67,90
14,16,38,39,42,66
DQa0~a7
DQb0~b7
DQc0~c7
DQd0~d7
DQPa~Pd
VDDQ
Data Inputs/Outputs
52,53,56,57,58,59,62,63
68,69,72,73,74,75,78,79
2,3,6,7,8,9,12,13
18,19,22,23,24,25,28,29
51,80,1,30
4,11,20,27,54,61,70,77
VSSQ
Output Power Supply
(2.5V or 3.3V)
Output Ground
5,10,21,26,55,60,71,76
Notes : 1. A0 and A1 are the two least significant bits(LSB) of the address field and set the internal burst counter if burst is desired.
2. The pin 42 is reserved for address bit for the 16Mb .
-3-
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
ADSP
ADV
A8
A9
83
82
81
49
50
A16
A17
ADSC
48
OE
85
A15
BW
86
84
GW
87
47
CLK
88
A14
VSS
89
46
VDD
90
A13
CS2
91
45
WEa
92
A12
WEb
93
44
N.C.
94
A11
N.C.
95
43
CS2
96
A18
CS1
97
42
A7
98
N.C.
A6
99
100 Pin TQFP
(20mm x 14mm)
31
32
33
34
35
36
37
38
39
40
41
A4
A3
A2
A1
A0
N.C.
N.C.
VSS
VDD
KM718V987(512Kx18)
A5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
LBO
N.C.
N.C.
N.C.
VDDQ
VSSQ
N.C.
N.C.
DQb0
DQb1
VSSQ
VDDQ
DQb2
DQb3
N.C.
VDD
N.C.
VSS
DQb4
DQb5
VDDQ
VSSQ
DQb6
DQb7
DQPb
N.C.
VSSQ
VDDQ
N.C.
N.C.
N.C.
100
PIN CONFIGURATION(TOP VIEW)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
A10
N.C.
N.C.
VDDQ
VSSQ
N.C.
DQPa
DQa7
DQa6
VSSQ
VDDQ
DQa5
DQa4
VSS
N.C.
VDD
ZZ
DQa3
DQa2
VDDQ
VSSQ
DQa1
DQa0
N.C.
N.C.
VSSQ
VDDQ
N.C.
N.C.
N.C.
PIN NAME
SYMBOL
PIN NAME
A0 - A 18
Address Inputs
ADV
ADSP
ADSC
CLK
CS1
CS2
CS2
WEx
OE
GW
BW
ZZ
LBO
Burst Address Advance
Address Status Processor
Address Status Controller
Clock
Chip Select
Chip Select
Chip Select
Byte Write Inputs
Output Enable
Global Write Enable
Byte Write Enable
Power Down Input
Burst Mode Control
TQFP PIN NO.
SYMBOL
32,33,34,35,36,37,43
44,45,46,47,48,49,50
80,81,82,99,100
83
84
85
89
98
97
92
93,94
86
88
87
64
31
PIN NAME
TQFP PIN NO.
VDD
VSS
N.C.
Power Supply(+3.3V)
Ground
No Connect
15,41,65,91
17,40,67,90
1,2,3,6,7,14,16,25,28,29,
30,38,39,42,51,52,53,56,
57,66,75,78,79,95,96
DQa0 ~ a 7
DQb0 ~ b 7
DQPa, Pb
VDDQ
Data Inputs/Outputs
58,59,62,63,68,69,72,73
8,9,12,13,18,19,22,23
74,24
4,11,20,27,54,61,70,77
VSSQ
Output Power Supply
(2.5V or 3.3V)
Output Ground
5,10,21,26,55,60,71,76
Notes : 1. A0 and A1 are the two least significant bits(LSB) of the address field and set the internal burst counter if burst is desired.
2. The pin 42 is reserved for address bit for the 16Mb .
-4-
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
119BGA PACKAGE PIN CONFIGURATIONS(TOP VIEW)
KM736V887(256Kx36)
1
2
3
4
5
6
7
A
VDDQ
A
A
ADSP
A
A
VDDQ
B
NC
CS2
A
ADSC
A
A
NC
C
NC
A
A
VDD
A
A
NC
D
DQc
DQPc
VSS
NC
VSS
DQPb
DQb
E
DQc
DQc
VSS
CS1
VSS
DQb
DQb
F
VDDQ
DQc
VSS
OE
VSS
DQb
VDDQ
G
DQc
DQc
WEc
ADV
WEb
DQb
DQb
H
DQc
DQc
VSS
GW
VSS
DQb
DQb
J
VDDQ
VDD
NC
VDD
NC
VDD
VDDQ
K
DQd
DQd
VSS
CLK
VSS
DQa
DQa
L
DQd
DQd
WEd
NC
WEa
DQa
DQa
M
VDDQ
DQd
VSS
BW
VSS
DQa
VDDQ
N
DQd
DQd
VSS
A1*
VSS
DQa
DQa
P
DQd
DQPd
VSS
A0*
VSS
DQPa
DQa
R
NC
A
LBO
VDD
NC
A
NC
T
NC
NC
A
A
A
NC
ZZ
U
VDDQ
NC
NC
NC
NC
NC
VDDQ
Note : * A0 and A1 are the two least significant bits(LSB) of the address field and set the internal burst counter if burst is desired.
PIN NAME
SYMBOL
PIN NAME
SYMBOL
PIN NAME
A
A0, A1
Address Inputs
Burst Count Address
VDD
VSS
Power Supply(+3.3V)
Ground
ADV
ADSP
ADSC
CLK
CS1
CS2
WEx
(x=a,b,c,d)
Burst Address Advance
Address Status Processor
Address Status Controller
Clock
Chip Select
Chip Select
Byte Write Inputs
N.C.
No Connect
DQa
DQb
DQc
DQd
DQPa~Pd
Data Inputs/Outputs
Data Inputs/Outputs
Data Inputs/Outputs
Data Inputs/Outputs
Data Inputs/Outpus
VDDQ
OE
GW
BW
ZZ
LBO
Output Enable
Global Write Enable
Byte Write Enable
Power Down Input
Burst Mode Control
Output Power Supply
(2.5V or 3.3V)
-5-
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
119BGA PACKAGE PIN CONFIGURATIONS(TOP VIEW)
KM718V987(512Kx18)
1
2
3
4
5
6
7
A
VDDQ
A
A
ADSP
A
A
VDDQ
B
NC
CS2
A
ADSC
A
A
NC
C
NC
A
A
VDD
A
A
NC
D
DQb
NC
VSS
NC
VSS
DQPa
NC
E
NC
DQb
VSS
CS 1
VSS
NC
DQa
F
VDDQ
NC
VSS
OE
VSS
DQa
VDDQ
G
NC
DQb
WEb
ADV
VSS
NC
DQa
H
DQb
NC
VSS
GW
VSS
DQa
NC
J
VDDQ
VDD
NC
VDD
NC
VDD
VDDQ
K
NC
DQb
VSS
CLK
VSS
NC
DQa
L
DQb
NC
VSS
NC
WEa
DQa
NC
M
VDDQ
DQb
VSS
BW
VSS
NC
VDDQ
N
DQb
NC
VSS
A1*
VSS
DQa
NC
P
NC
DQPb
VSS
A0*
VSS
NC
DQa
R
NC
A
LBO
VDD
NC
A
NC
T
NC
A
A
NC
A
A
ZZ
U
VDDQ
NC
NC
NC
NC
NC
VDDQ
Note : * A0 and A 1 are the two least significant bits(LSB) of the address field and set the internal burst counter if burst is desired.
PIN NAME
SYMBOL
PIN NAME
SYMBOL
PIN NAME
A
A0,A1
Address Inputs
Burst Count Address
VDD
VSS
Power Supply(+3.3V)
Ground
ADV
ADSP
ADSC
CLK
CS1
CS2
WEx
(x=a,b)
Burst Address Advance
Address Status Processor
Address Status Controller
Clock
Chip Select
Chip Select
Byte Write Inputs
N.C.
No Connect
DQa
DQb
DQPa~Pb
Data Inputs/Outputs
Data Inputs/Outputs
Data Inputs/Outpus
VDDQ
Output Power Supply
(2.5V or 3.3V)
OE
GW
BW
ZZ
LBO
Output Enable
Global Write Enable
Byte Write Enable
Power Down Input
Burst Mode Control
-6-
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
FUNCTION DESCRIPTION
The KM736V887 and KM718V987 are synchronous SRAM designed to support the burst address accessing sequence of the Power
PC based microprocessor. All inputs (with the exception of OE, LBO and ZZ) are sampled on rising clock edges. The start and duration of the burst access is controlled by ADSC, ADSP and ADV and chip select pins.
The accesses are enabled with the chip select signals and output enabled signals. Wait states are inserted into the access with
ADV.
When ZZ is pulled high, the SRAM will enter a Power Down State. At this time, internal state of the SRAM is preserved. When ZZ
returns to low, the SRAM normally operates after 2cycles of wake up time. ZZ pin is pulled down internally.
Read cycles are initiated with ADSP(or ADSC) using the new external address clocked into the on-chip address register when both
GW and BW are high or when BW is low and WEa, WEb, WEc, and WEd are high. When ADSP is sampled low, the chip selects are
sampled active, and the output buffer is enabled with OE. the data of cell array accessed by the current address are projected to the
output pins.
Write cycles are also initiated with ADSP(or ADSC) and are differentiated into two kinds of operations; All byte write operation and
individual byte write operation.
All byte write occurs by enabling GW(independent of BW and WEx.), and individual byte write is performed only when GW is high
and BW is low. In KM736V887, a 256Kx36 organization, WEa controls DQa0 ~ DQa7 and DQPa, WEb controls DQb0 ~ DQb7 and
DQPb, WEc controls DQc0 ~ DQc7 and DQPc and WEd controls DQd0 ~ DQd7 and DQPd.
CS1 is used to enable the device and conditions internal use of ADSP and is sampled only when a new external address is loaded.
ADV is ignored at the clock edge when ADSP is asserted, but can be sampled on the subsequent clock edges. The address
increases internally for the next access of the burst when ADV is sampled low.
Addresses are generated for the burst access as shown below, The starting point of the burst sequence is provided by the external
address. The burst address counter wraps around to its initial state upon completion. The burst sequence is determined by the state
of the LBO pin. When this pin is Low, linear burst sequence is selected. And this pin is High, Interleaved burst sequence is selected.
BURST SEQUENCE TABLE
LBO PIN
HIGH
First Address
Fourth Address
(Interleaved Burst)
Case 1
A1
0
0
1
1
Case 2
A0
0
1
0
1
A1
0
0
1
1
Case 3
A0
1
0
1
0
A1
1
1
0
0
Case 4
A0
0
1
0
1
A1
1
1
0
0
BQ TABLE
LBO PIN
A0
1
0
1
0
(Linear Burst)
LOW
First Address
Fourth Address
Case 1
A1
0
0
1
1
Case 2
A0
0
1
0
1
A1
0
1
1
0
Case 3
A0
1
0
1
0
A1
1
1
0
0
Case 4
A0
0
1
0
1
A1
1
0
0
1
A0
1
0
1
0
Note : 1. LBO pin must be tied to High or Low, and Floating State must not be allowed.
-7-
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
TRUTH TABLES
SYNCHRONOUS TRUTH TABLE
CS1
CS2
CS2
ADV
WRITE
CLK
ADDRESS ACCESSED
OPERATION
H
X
X
ADSP ADSC
X
L
X
X
↑
N/A
Not Selected
L
L
X
L
X
X
X
↑
N/A
Not Selected
L
X
H
L
X
X
X
↑
N/A
Not Selected
L
L
X
X
L
X
X
↑
N/A
Not Selected
L
X
H
X
L
X
X
↑
N/A
Not Selected
L
H
L
L
X
X
X
↑
External Address
Begin Burst Read Cycle
L
H
L
H
L
X
L
↑
External Address
Begin Burst Write Cycle
L
H
L
H
L
X
H
↑
External Address
Begin Burst Read Cycle
X
X
X
H
H
L
H
↑
Next Address
Continue Burst Read Cycle
H
X
X
X
H
L
H
↑
Next Address
Continue Burst Read Cycle
X
X
X
H
H
L
L
↑
Next Address
Continue Burst Write Cycle
H
X
X
X
H
L
L
↑
Next Address
Continue Burst Write Cycle
X
X
X
H
H
H
H
↑
Current Address
Suspend Burst Read Cycle
H
X
X
X
H
H
H
↑
Current Address
Suspend Burst Read Cycle
X
X
X
H
H
H
L
↑
Current Address
Suspend Burst Write Cycle
H
X
X
X
H
H
L
↑
Current Address
Suspend Burst Write Cycle
Notes : 1. X means "Don′t Care".
2. The rising edge of clock is symbolized by ↑.
3. WRITE = L means Write operation in WRITE TRUTH TABLE.
WRITE = H means Read operation in WRITE TRUTH TABLE.
4. Operation finally depends on status of asynchronous input pins(ZZ and OE).
WRITE TRUTH TABLE ( x36)
GW
BW
WEa
WEb
H
H
X
X
H
L
H
H
H
L
L
H
H
L
H
L
H
L
H
H
L
L
L
X
X
WEc
WEd
OPERATION
X
X
READ
H
H
READ
H
H
WRITE BYTE a
H
H
WRITE BYTE b
H
L
L
WRITE BYTE c and d
L
L
L
WRITE ALL BYTEs
X
X
X
WRITE ALL BYTEs
Notes : 1. X means "Don′t Care".
2. All inputs in this table must meet setup and hold time around the rising edge of CLK(↑).
WRITE TRUTH TABLE(x18)
GW
BW
WEa
WEb
OPERATION
H
H
X
X
READ
H
L
H
H
READ
H
L
L
H
WRITE BYTE a
H
L
H
L
WRITE BYTE b
H
L
L
L
WRITE ALL BYTEs
L
X
X
X
WRITE ALL BYTEs
Notes : 1. X means "Don′t Care".
2. All inputs in this table must meet setup and hold time around the rising edge of CLK( ↑).
-8-
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
ASYNCHRONOUS TRUTH TABLE
Operation
ZZ
OE
I/O STATUS
Sleep Mode
H
X
High-Z
L
L
DQ
Read
L
H
High-Z
Write
L
X
Din, High-Z
Deselected
L
X
High-Z
Notes
1. X means "Don′t Care".
2. ZZ pin is pulled down internally
3. For write cycles that following read cycles, the output buffers must be
disabled with OE, otherwise data bus contention will occur.
4. Sleep Mode means power down state of which stand-by current does
not depend on cycle time.
5. Deselected means power down state of which stand-by current
depends on cycle time.
ABSOLUTE MAXIMUM RATINGS*
PARAMETER
SYMBOL
RATING
UNIT
Voltage on V DD Supply Relative to VSS
VDD
-0.3 to 4.6
V
Voltage on V DDQ Supply Relative to VSS
VDDQ
VDD
V
Voltage on Input Pin Relative to VSS
VIN
-0.3 to 4.6
V
Voltage on I/O Pin Relative to VSS
VIO
-0.3 to VDDQ+0.5
V
Power Dissipation
PD
1.4
W
Storage Temperature
TSTG
-65 to 150
°C
Operating Temperature
TOPR
0 to 70
°C
Storage Temperature Range Under Bias
TBIAS
-10 to 85
°C
*Notes : Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
OPERATING CONDITIONS at 3.3V I/O(0°C ≤ TA ≤ 70°C)
PARAMETER
Supply Voltage
Ground
SYMBOL
MIN
Typ.
MAX
UNIT
VDD
3.135
3.3
3.465
V
VDDQ
3.135
3.3
3.465
V
VSS
0
0
0
V
OPERATING CONDITIONS at 2.5V I/O(0°C ≤ TA ≤ 70°C)
PARAMETER
Supply Voltage
Ground
SYMBOL
MIN
Typ.
MAX
UNIT
VDD
3.135
3.3
3.465
V
VDDQ
2.375
2.5
2.9
V
VSS
0
0
0
V
CAPACITANCE*(TA=25°C, f=1MHz)
PARAMETER
Input Capacitance
Output Capacitance
SYMBOL
TEST CONDITION
MIN
MAX
UNIT
CIN
VIN=0V
-
6
pF
COUT
VOUT=0V
-
8
pF
*Note : Sampled not 100% tested.
-9-
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
DC ELECTRICAL CHARACTERISTICS(VDD=3.3V+0.165V/-0.165V, TA=0°C to +70°C)
Parameter
Symbol
Test Conditions
Min
Max
Unit
Input Leakage Current(except ZZ)
IIL
VDD=Max ; VIN=VSS to VDD
-2
+2
µA
Output Leakage Current
IOL
Output Disabled, Vout=VSS to V DDQ
-2
+2
µA
Operating Current
ICC
-7
-
350
Device Selected, IOUT=0mA,
-8
-
330
ZZ≤VIL , Cycle Time ≥ tCYC Min
-9
-
300
-10
-
260
-7
-
140
-8
-
130
-9
-
120
-10
-
120
-
30
mA
Device deselected, IOUT=0mA,
ISB
ZZ≤VIL, f=Max, All Inputs≤0.2V or
≥ VDD-0.2V
Standby Current
ISB1
Device deselected, I OUT=0mA, ZZ≤0.2V, f=0,
All Inputs=fixed (VDD-0.2V or 0.2V)
Device deselected, IOUT=0mA, ZZ≥VDD-0.2V,
mA
Notes
1,2
mA
ISB2
f=Max, All Inputs≤VIL or ≥VIH
-
30
mA
Output Low Voltage(3.3V I/O)
VOL
IOL=8.0mA
-
0.4
V
Output High Voltage(3.3V I/O)
VOH
IOH=-4.0mA
2.4
-
V
Output Low Voltage(2.5V I/O)
VOL
IOL=1.0mA
-
0.4
V
Output High Voltage(2.5V I/O)
VOH
IOH=-1.0mA
Input Low Voltage(3.3V I/O)
VIL
Input High Voltage(3.3V I/O)
2.0
-
V
-0.3*
0.8
V
VIH
2.0
VDD+0.5**
V
Input Low Voltage(2.5V I/O)
VIL
-0.3*
0.7
V
Input High Voltage(2.5V I/O)
VIH
1.7
VDD+0.5**
V
3
3
Notes : 1. Reference AC Operating Conditions and Characteristics for input and timing.
2. Data states are all zero.
3. In Case of I/O Pins, the Max. VIH=VDDQ+0.3V
VIH
VSS
VSS-1.0V
20% tCYC(MIN)
TEST CONDITIONS
(VDD=3.3V+0.165V/-0.165V,VDDQ=3.3V+0.165/-0.165V or VDD=3.3V+0.165V/-0.165V,VDDQ=2.5V+0.4V/-0.125V, TA=0to70°C)
PARAMETER
VALUE
Input Pulse Level(for 3.3V I/O)
0 to 3.0V
Input Pulse Level(for 2.5V I/O)
0 to 2.5V
Input Rise and Fall Time(Measured at 20% to 80% for 3.3V I/O)
1.0V/ns
Input Rise and Fall Time(Measured at 20% to 80% for 2.5V I/O)
1.0V/ns
Input and Output Timing Reference Levels for 3.3V I/O
1.5V
Input and Output Timing Reference Levels for 2.5V I/O
VDDQ/2
Output Load
See Fig. 1
- 10 -
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
Output Load(A)
Output Load(B),
(for tLZC, tLZOE, tHZOE & tHZC)
+3.3V for 3.3V I/O
/+2.5V for 2.5V I/O
RL=50Ω
Dout
VL=1.5V for 3.3V I/O
VDDQ/2 for 2.5V I/O
319Ω / 1667Ω
Dout
Zo=50Ω
353Ω / 1538Ω
5pF*
* Including Scope and Jig Capacitance
Fig. 1
AC TIMING CHARACTERISTICS(VDD=3.3V+0.165V/-0.165V, TA=0°C to +70°C)
PARAMETER
SYMBOL
-7
-8
-9
-10
UNIT
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
-
ns
Cycle Time
tCYC
8.5
-
10
-
12
-
12
Clock Access Time
tCD
-
7.5
-
8.5
-
9.0
-
10
ns
Output Enable to Data Valid
tOE
-
3.5
-
3.5
-
3.5
-
3.5
ns
Clock High to Output Low-Z
tLZC
2.5
-
2.5
-
2.5
-
2.5
-
ns
Output Hold from Clock High
tOH
2.5
-
2.5
-
2.5
-
2.5
-
ns
Output Enable Low to Output Low-Z
tLZOE
0
-
0
-
0
-
0
-
ns
Output Enable High to Output High-Z
tHZOE
-
3.5
-
3.5
-
3.5
-
4.0
ns
Clock High to Output High-Z
tHZC
-
4.0
-
5.0
-
5.0
-
6.0
ns
Clock High Pulse Width
tCH
2.5
-
3.0
-
3.0
-
3.0
-
ns
Clock Low Pulse Width
tCL
2.5
-
3.0
-
3.0
-
3.0
-
ns
Address Setup to Clock High
tAS
2.0
-
2.0
-
2.0
-
2.0
-
ns
Address Status Setup to Clock High
tSS
2.0
-
2.0
-
2.0
-
2.0
-
ns
Data Setup to Clock High
tDS
2.0
-
2.0
-
2.0
-
2.0
-
ns
tWS
2.0
-
2.0
-
2.0
-
2.0
-
ns
Address Advance Setup to Clock High
tADVS
2.0
-
2.0
-
2.0
-
2.0
-
ns
Chip Select Setup to Clock High
tCSS
2.0
-
2.0
-
2.0
-
2.0
-
ns
Address Hold from Clock High
tAH
0.5
-
0.5
-
0.5
-
0.5
-
ns
Address Status Hold from Clock High
tSH
0.5
-
0.5
-
0.5
-
0.5
-
ns
Data Hold from Clock High
tDH
0.5
-
0.5
-
0.5
-
0.5
-
ns
Write Hold from Clock High (GW, BW, WEX)
tWH
0.5
-
0.5
-
0.5
-
0.5
-
ns
Address Advance Hold from Clock High
tADVH
0.5
-
0.5
-
0.5
-
0.5
-
ns
Chip Select Hold from Clock High
tCSH
0.5
-
0.5
-
0.5
-
0.5
-
ns
Write Setup to Clock High (GW, BW, WEX)
ZZ High to Power Down
tPDS
2
-
2
-
2
-
2
-
cycle
ZZ Low to Power Up
tPUS
2
-
2
-
2
-
2
-
cycle
Notes : 1. All address inputs must meet the specified setup and hold times for all rising clock edges whenever ADSC and/or ADSP is sampled low and
CS is sampled low. All other synchronous inputs must meet the specified setup and hold times whenever this device is chip selected.
2. Both chip selects must be active whenever ADSC or ADSP is sampled low in order for the this device to remain enabled.
3. ADSC or ADSP must not be asserted for at least 2 Clock after leaving ZZ state.
- 11 -
May 1999
Rev 4.0
- 12 -
Data Out
OE
ADV
CS
WRITE
ADDRESS
ADSC
ADSP
CLOCK
tCSS
tAS
tSS
tOE
Q1-1
tHZOE
tADVH
tWH
tSS
A2
tSH
Q2-1
tCD
tOH
Q2-2
Q2-3
A3
Q2-4
(ADV INSERTS WAIT STATE)
BURST CONTINUED WITH
NEW BASE ADDRESS
tCYC
tCL
NOTES : WRITE = L means GW = L, or GW = H, BW = L, WEx.= L
CS = L means CS1 = L, CS2 = H and CS2 = L
CS = H means CS1 = H, or CS1 = L and CS2 = H, or CS1 = L, and CS2 = L
tADVS
tCSH
tWS
tLZOE
A1
tAH
tSH
tCH
TIMING WAVEFORM OF READ CYCLE
Q3-1
Q3-2
Q3-3
Undefined
Don′t Care
Q3-4
tHZC
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
May 1999
Rev 4.0
- 13 -
Data Out
Data In
OE
ADV
CS
WRITE
ADDRESS
ADSC
ADSP
CLOCK
Q0-3
tCSS
tAS
tSS
Q0-4
A1
tLZOE
tCSH
tAH
tSH
D1-1
tCL
tCYC
tCH
A2
D2-1
D2-2
(ADV SUSPENDS BURST)
D2-2
D2-3
(ADSC EXTENDED BURST)
TIMING WAVEFORM OF WRTE CYCLE
D2-4
D3-1
A3
tDS
tADVS
tWS
tSS
D3-2
tDH
tADVH
tWH
tSH
D3-3
Undefined
Don′t Care
D3-4
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
May 1999
Rev 4.0
- 14 -
Data Out
Data In
OE
ADV
CS
WRITE
ADDRESS
ADSP
CLOCK
tHZC
tSS
A1
tLZC
tCD
tSH
Q1-1
tHZOE
tAS
A2
tCL
tCYC
tDS
tADVS
tWS
tAH
tCH
D2-1
tDH
tADVH
tWH
A3
tLZOE
tOE
Q3-1
Q3-2
Q3-3
tOH
Q3-4
TIMING WAVEFORM OF COMBINATION READ/WRTE CYCLE(ADSP CONTROLLED, ADSC=HIGH)
Undefined
Don′t Care
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
May 1999
Rev 4.0
- 15 -
Data In
Data Out
OE
ADV
CS
WRITE
ADDRESS
ADSC
CLOCK
tCSS
tSS
A1
tLZOE
tOE
tCSH
tSH
Q1-1
A2
Q2-1
A3
Q3-1
A4
Q4-1
tHZOE
D5-1
A5
tDS
tWS
D6-1
A6
tDH
tWH
D7-1
A7
tWS
tCD
A8
A9
Q8-1
tCL
tCYC
tWH
tCH
TIMING WAVEFORM OF SINGLE READ/WRITE CYCLE(ADSC CONTROLLED, ADSP=HIGH)
Undefined
Don′t Care
Q9-1
tOH
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
May 1999
Rev 4.0
- 16 -
Data In
Data Out
OE
ADV
CS
WRITE
ADDRESS
ADSP
CLOCK
tCSS
tSS
tOE
tCSH
tLZOE
A1
tSH
Q1-1
A2
Q2-1
A3
tAS
Q3-1
A4
tAH
tCYC
tCH
A5
Q4-1
tCL
tHZOE
D5-1
A6
tDS
D6-1
tDH
A7
D7-1
tCD
A8
Q8-1
A9
TIMING WAVEFORM OF SINGLE READ/WRITE CYCLE(ADSP CONTROLLED, ADSC=HIGH)
Q9-1
tOH
Undefined
Don′t Care
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
May 1999
Rev 4.0
- 17 -
ZZ
Data Out
Data In
OE
ADV
CS
WRITE
ADDRESS
ADSC
ADSP
CLOCK
tCSS
tAS
tSS
A1
tLZOE
tOE
tCSH
tAH
tSH
Q1-1
ZZ Setup Cycle
tPDS
tHZC
Sleep State
tPUS
tCL
ZZ Recovery Cycle
tCYC
tCH
TIMING WAVEFORM OF POWER DOWN CYCLE
tWS
Normal Operation Mode
tHZOE
A2
D2-1
tWH
Undefined
Don′t Care
D2-2
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
APPLICATION INFORMATION
DEPTH EXPANSION
The Samsung 256Kx36 Synchronous Burst SRAM has two additional chip selects for simple depth expansion.
This permits easy secondary cache upgrades from 256K depth to 512K depth without extra logic.
I/O[0:71]
Data
Address
A[0:18]
A[18]
A[0:17]
A[18]
A[0:17]
Address Data
Address Data
CLK
CS2
CS2
CS2
CS2
CLK
Microprocessor
Address
ADSC
CLK
WEx
OE
Cache
Controller
256Kx36
SB
SRAM
ADSC
WEx
(Bank 0)
OE
256Kx36
SB
SRAM
(Bank 1)
CS1
CS1
ADV
CLK
ADSP
ADV
ADSP
ADS
INTERLEAVE READ TIMING (Refer to non-interleave write timing for interleave write timing)
(ADSP CONTROLLED , ADSC=HIGH)
CLOCK
tSS
tSH
ADSP
tAS
ADDRESS
[0:n]
tAH
A1
A2
tWS
tWH
WRITE
tCSS
tCSH
CS1
Bank 0 is selected by CS2, and Bank 1 deselected by CS2
An+1
tADVS
Bank 0 is deselected by CS2 , and Bank 1 selected by CS2
tADVH
ADV
OE
tOE
Data Out
(Bank 0)
Data Out
(Bank 1)
tLZOE
tHZC
Q1-1
Q1-2
Q1-3
Q1-4
tCD
tLZC
Q2-1
*Notes : n = 14 32K depth ,
16 128K depth ,
18 512K depth
15 64K depth
17 256K depth
Q2-2
Q2-3
Q2-4
Don′t Care
- 18 -
Undefined
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
APPLICATION INFORMATION
DEPTH EXPANSION
The Samsung 512Kx18 Synchronous Burst SRAM has two additional chip selects for simple depth expansion.
This permits easy secondary cache upgrades from 512K depth to 1M depth without extra logic.
I/O[0:71]
Data
Address
A[19]
A[0:19]
A[19]
A[0:18]
Address Data
CLK
Microprocessor
CS2
CS2
CS2
ADSC
CLK
WEx
OE
Cache
Controller
Address Data
CS2
CLK
Address
A[0:18]
512Kx18
SB
SRAM
CLK
ADSC
WEx
(Bank 0)
OE
(Bank 1)
CS1
CS1
ADV
512Kx18
SB
SRAM
ADV
ADSP
ADSP
ADS
INTERLEAVE READ TIMING (Refer to non-interleave write timing for interleave write timing)
(ADSP CONTROLLED , ADSC=HIGH)
CLOCK
tSS
tSH
ADSP
tAS
ADDRESS
[0:n]
tAH
A1
A2
tWS
tWH
WRITE
tCSS
tCSH
CS1
Bank 0 is selected by CS2, and Bank 1 deselected by CS2
An+1
tADVS
Bank 0 is deselected by CS2 , and Bank 1 selected by CS2
tADVH
ADV
OE
tOE
Data Out
(Bank 0)
Data Out
(Bank 1)
tLZOE
tHZC
Q1-1
Q1-2
Q1-3
Q1-4
tCD
tLZC
Q2-1
*Notes : n = 14 32K depth ,
16 128K depth ,
18 512K depth ,
15 64K depth
17 256K depth
19 1M depth
Q2-2
Q2-3
Q2-4
Don′t Care
- 19 -
Undefined
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
PACKAGE DIMENSIONS
100-TQFP-1420A
Units ; millimeters/Inches
22.00
±0.30
20.00
±0.20
0~8°
0.10
0.127 +- 0.05
16.00
±0.30
14.00 ±0.20
0.10 MAX
(0.83)
0.50 ±0.10
#1
0.65
(0.58)
0.30 ±0.10
0.10 MAX
1.40
0.50 ±0.10
- 20 -
±0.10
1.60 MAX
0.05 MIN
May 1999
Rev 4.0
KM736V887
KM718V987
256Kx36 & 512Kx18 Synchronous SRAM
119BGA PACKAGE DIMENSIONS
14.00±0.10
1.27
1.27
22.00±0.10
Indicator of
Ball(1A) Location
20.50±0.10
C0.70
C1.00
0.750±0.15
1.50REF
0.60±0.10
0.60±0.10
12.50±0.10
NOTE :
1. All Dimensions are in Millimeters.
2. Solder Ball to PCB Offset : 0.10 MAX.
3. PCB to Cavity Offset : 0.10 MAX.
- 21 -
May 1999
Rev 4.0