74LVX16374 LOW VOLTAGE CMOS 16-BIT D-TYPE FLIP FLOP (3-STATE) WITH 5V TOLERANT INPUTS ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: fMAX = 160 MHz (TYP.) at VCC = 3V 5V TOLERANT INPUTS POWER DOWN PROTECTION ON INPUTS INPUT VOLTAGE LEVEL: VIL = 0.8V, VIH = 2V at VCC =3V LOW POWER DISSIPATION: ICC = 4 µA (MAX.) at TA=25°C LOW NOISE: VOLP = 0.3V (TYP.) at VCC =3.3V SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 4 mA (MIN) at VCC =3V BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 2V to 3.6V (1.2V Data Retention) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 16373 IMPROVED LATCH-UP IMMUNITY TSSOP ORDER CODES PACKAGE TSSOP TUBE T&R 74LVX16374TTR PIN CONNECTION DESCRIPTION The 74LVX16374 is a low voltage CMOS 16 BIT D-TYPE FLIP-FLOP with 3 STATE OUTPUTS NON INVERTING fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It is ideal for low power, battery operated and low noise 3.3V applications. These 16 bit D-TYPE flip-flop is controlled by two clock inputs (CK) and two output enable inputs (nOE). The device can be used as two 8-bit flip-flops or one 16-bit flip-flop.On the positive transition of the clock, the Q outputs will be set to the logic state that were setup at the D inputs. While the (OE) input is low, the outputs will be in a normal logic state (high or low logic level); while OE is high, the outputs will be in a high impedance state.The output control does not affect the internal operation of flip-flops; that is, the old data can be retained or the new data can be entered even while the outputs are off.Power down protection is provided on all inputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage.This device can be used to interface 5V to 3V. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. February 2003 1/10 74LVX16374 INPUT EQUIVALENT CIRCUIT IEC LOGIC SYMBOLS PIN DESCRIPTION PIN No SYMBOL 1 1OE NAME AND FUNCTION 3 State Output Enable Input (Active LOW) 2, 3, 5, 6, 8, 9, 1Q0 to 1Q7 3-State Outputs 11, 12 13, 14, 16, 17, 2Q0 to 2Q7 3-State Outputs 19, 20, 22, 23 3 State Output Enable 24 2OE Input (Active LOW) 25 2CK Clock Input 36, 35, 33, 32, 2D0 to 2D7 Data Inputs 30, 29, 27, 26 47, 46, 44, 43, 1D0 to 1D7 Data Inputs 41, 40, 38, 37 48 1CK Clock Input 4, 10, 15, 21, GND Ground (0V) 28, 34, 39, 45 7, 18, 31, 42 VCC Positive Supply Voltage TRUTH TABLE INPUTS OE CK D H X Q X Z L X NO CHANGE L L L L H H X : Don‘t Care Z : High Impedance 2/10 OUTPUT 74LVX16374 LOGIC DIAGRAM This logic diagram has not to be used to estimate propagation delays ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage -0.5 to VCC + 0.5 V IIK DC Input Diode Current - 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ICC or IGND DC VCC or Ground Current Tstg Storage Temperature TL Lead Temperature (10 sec) ± 50 mA -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied RECOMMENDED OPERATING CONDITIONS Symbol Value Unit Supply Voltage (note 1) 2 to 3.6 V VI Input Voltage 0 to 5.5 V VO Output Voltage Top Operating Temperature VCC dt/dv Parameter Input Rise and Fall Time (note 2) (VCC = 3V) 0 to VCC V -55 to 125 °C 0 to 100 ns/V 1) Truth Table guaranteed: 1.2V to 3.6V 2) VIN from 0.8V to 2.0V 3/10 74LVX16374 DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH VOL IOZ II ICC Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage High Impedance Output Leakage Current Input Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 3.0 3.6 2.0 3.0 3.6 Typ. Max. 1.5 2.0 2.4 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 2.0 2.4 0.5 0.8 0.8 2.0 IO=-50 µA 1.9 2.0 1.9 1.9 IO=-50 µA 2.9 3.0 2.9 2.9 3.0 IO=-4 mA 2.58 2.0 IO=50 µA 0.0 0.0 2.48 V 0.5 0.8 0.8 3.0 0.1 Max. 1.5 2.0 2.4 0.5 0.8 0.8 Unit V V 2.4 0.1 0.1 3.0 IO=50 µA 0.1 0.1 0.1 3.0 IO=4 mA 0.36 0.44 0.55 3.6 VI = VIH or VIL VO = VCC or GND ±0.25 ± 2.5 ± 2.5 µA 3.6 VI = 5V or GND ± 0.1 ±1 ±1 µA 3.6 VI = VCC or GND 4 40 40 µA V DYNAMIC SWITCHING CHARACTERISTICS Test Condition Symbol VOLP VOLV VIHD VILD Parameter Dynamic Low Voltage Quiet Output (note 1, 2) Dynamic High Voltage Input (note 1, 3) Dynamic Low Voltage Input (note 1, 3) TA = 25°C VCC (V) Min. 3.3 3.3 3.3 Value -0.8 CL = 50 pF Typ. Max. 0.3 0.8 -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. -0.3 V 2.0 0.8 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 3.3V, (n-1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to 3.3V. Inputs under test switching: 3.3V to threshold (V ILD), 0V to threshold (VIHD), f=1MHz. 4/10 74LVX16374 AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3ns) Test Condition Symbol tPLH tPHL tPZL tPZH Parameter Propagation Delay Time CK to Q Output Enable Time tPLZ tPHZ Output Disable Time tW CK pulse Width, HIGH tS Setup Time D to CK HIGH or LOW th Hold Time D to CK HIGH or LOW fMAX tOSLH tOSHL Maximum Clock Frequency Output to Output Skew Time (note 1,2) VCC (V) CL (pF) 2.7 2.7 Value TA = 25°C Min. -40 to 85°C -55 to 125°C Typ. Max. Min. Max. Min. Max. 15 9.5 16.3 1.0 19.5 1.0 20.5 50 11.0 19.8 1.0 23.0 1.0 24.0 (*) 3.3 15 9 15 1 17 1 17 3.3(*) 2.7 2.7 50 10.6 16.2 1 18.5 1 18.5 15 50 8.6 10.1 14.5 18.0 1.0 1.0 17.5 21.0 1.0 1.0 18.5 22.0 3.3(*) 15 8 13 1 15 1 15 3.3(*) 2.7 50 9.6 14.9 1 16 1 16 50 11.5 18.5 1.0 22.0 1.0 23.0 3.3(*) 2.7 50 9.6 13.2 1.0 15.0 1.0 16.0 50 5 5 5 5 3.3(*) 50 5 5 5 5 2.7 50 4.5 4 4 3.3(*) 50 3 3 3 50 2 2 2 3.3(*) 50 2 2 2 2.7 2.7 15 50 60 45 115 60 50 40 45 35 3.3(*) 15 100 160 85 75 3.3(*) 2.7 50 80 130 50 0.5 1.0 1.5 1.5 3.3(*) 50 0.5 1.0 1.5 1.5 70 ns ns ns ns ns 2.7 70 Unit ns MHz 80 ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW 2) Parameter guaranteed by design (*) Voltage range is 3.3V ± 0.3V CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter CIN Input Capacitance COUT Output Capacitance Power Dissipation Capacitance (note 1) CPD TA = 25°C VCC (V) 3.0 Value Min. fIN = 10MHz Typ. Max. 2.5 10 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF 4 pF 17 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/16 (per circuit) 5/10 74LVX16374 TEST CIRCUIT TEST SWITCH tPLH, tPHL Open tPZL, tPLZ VCC tPZH, tPHZ GND CL = 15/50 pF or equivalent (includes jig and probe capacitance) RL = R1 = 1KΩ or equivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1 PROPAGATION DELAYS, SETUP AND HOLD TIMES, MAXIMUM CLOCK FREQUENCY (f=1MHz; 50% duty cycle) 6/10 74LVX16374 WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) WAVEFORM 3 : CLOCK PULSE WIDTH (f=1MHz; 50% duty cycle) 7/10 74LVX16374 TSSOP48 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. A MIN. TYP. 1.2 A1 0.05 0.047 0.15 A2 MAX. 0.002 0.006 0.9 0.035 b 0.17 0.27 0.0067 0.011 c 0.09 0.20 0.0035 0.0079 D 12.4 12.6 0.488 0.496 E 8.1 BSC E1 6.0 0.318 BSC 6.2 e 0.236 0.5 BSC 0.244 0.0197 BSC K 0˚ 8˚ 0˚ 8˚ L 0.50 0.75 0.020 0.030 A A2 A1 b K e L E c D E1 PIN 1 IDENTIFICATION 1 7065588C 8/10 74LVX16374 Tape & Reel TSSOP48 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 30.4 0.519 1.197 Ao 8.7 8.9 0.343 0.350 Bo 13.1 13.3 0.516 0.524 Ko 1.5 1.7 0.059 0.067 Po 3.9 4.1 0.153 0.161 P 11.9 12.1 0.468 0.476 9/10 74LVX16374 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com 10/10