STMICROELECTRONICS M74HC03TTR

M74HC03
QUAD 2-INPUT OPEN DRAIN NAND GATE
■
■
■
■
■
■
HIGH SPEED:
tPD = 8ns (TYP.) at VCC = 6V
LOW POWER DISSIPATION:
ICC = 1µA(MAX.) at TA=25°C
HIGH NOISE IMMUNITY:
VNIH = V NIL = 28 % VCC (MIN.)
BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL
WIDE OPERATING VOLTAGE RANGE:
VCC (OPR) = 2V to 6V
PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 03
DESCRIPTION
The M74HC03 is an high speed CMOS QUAD
2-INPUT OPEN DRAIN NAND GATE fabricated
with silicon gate C2MOS technology.
The internal circuit is composed of 3 stages
including buffer output, which enables high noise
immunity and stable output. This device can, with
an external pull-up resistor, be used in wired AND
configuration. This device can be also used as a
DIP
SOP
TSSOP
ORDER CODES
PACKAGE
TUBE
DIP
SOP
TSSOP
M74HC03B1R
M74HC03M1R
T&R
M74HC03RM13TR
M74HC03TTR
led driver and in any other application requiring a
current sink.
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
PIN CONNECTION AND IEC LOGIC SYMBOLS
July 2001
1/8
M74HC03
INPUT AND OUTPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION
PIN No
SYMBOL
1, 4, 9, 12
2, 5, 10, 13
3, 6, 8, 11
7
1A to 4A
1B to 4B
1Y to 4Y
GND
VCC
14
NAME AND FUNCTION
Data Inputs
Data Inputs
Data Outputs
Ground (0V)
Positive Supply Voltage
TRUTH TABLE
A
B
Y
L
L
H
H
L
H
L
H
Z
Z
Z
L
Z : High Impedance
ABSOLUTE MAXIMUM RATINGS
Symbol
VCC
Parameter
Supply Voltage
Value
Unit
-0.5 to +7
V
VI
DC Input Voltage
-0.5 to VCC + 0.5
V
VO
DC Output Voltage
-0.5 to VCC + 0.5
± 20
V
mA
IIK
DC Input Diode Current
IOK
DC Output Diode Current
± 20
mA
IO
DC Output Current
+ 25
mA
ICC or IGND DC VCC or Ground Current
PD
Power Dissipation
Tstg
Storage Temperature
TL
Lead Temperature (10 sec)
± 50
mA
500(*)
mW
-65 to +150
°C
300
°C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Parameter
Supply Voltage
Unit
2 to 6
V
V
VI
Input Voltage
0 to VCC
VO
Output Voltage
0 to VCC
V
Top
Operating Temperature
-55 to 125
°C
VCC = 2.0V
0 to 1000
ns
VCC = 4.5V
0 to 500
ns
VCC = 6.0V
0 to 400
ns
Input Rise and Fall Time
tr, tf
2/8
Value
M74HC03
DC SPECIFICATIONS
Test Condition
Symbol
VIH
VIL
VOL
II
IOZ
ICC
Parameter
High Level Input
Voltage
Low Level Input
Voltage
Low Level Output
Voltage
Input Leakage
Current
Output Leakage
Current
Quiescent Supply
Current
Value
TA = 25°C
VCC
(V)
Min.
2.0
4.5
6.0
2.0
4.5
6.0
Typ.
Max.
1.5
3.15
4.2
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
1.5
3.15
4.2
Unit
Max.
1.5
3.15
4.2
V
0.5
1.35
1.8
0.5
1.35
1.8
0.5
1.35
1.8
2.0
IO=20 µA
0.0
0.1
0.1
0.1
4.5
IO=20 µA
0.0
0.1
0.1
0.1
V
6.0
IO=20 µA
0.0
0.1
0.1
0.1
4.5
IO=4.0 mA
0.17
0.26
0.33
0.40
6.0
IO=5.2 mA
0.18
0.26
0.33
0.40
6.0
VI = VCC or GND
± 0.1
±1
±1
µA
6.0
VI = VIH or VIL
VO = VCC or GND
±0.5
±5
± 10
µA
6.0
VI = VCC or GND
1
10
20
µA
V
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
Test Condition
Symbol
tTHL
tPLZ
tPZL
Parameter
Output Transition
Time
Propagation Delay
Time
Propagation Delay
Time
Value
TA = 25°C
VCC
(V)
Min.
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
RL = 1 KΩ
RL = 1 KΩ
Typ.
Max.
30
8
7
16
9
8
23
7
6
75
15
13
60
12
10
60
12
10
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
95
19
16
75
15
13
75
15
13
Unit
Max.
110
22
19
90
18
15
90
18
15
ns
ns
ns
CAPACITIVE CHARACTERISTICS
Test Condition
Symbol
Parameter
VCC
(V)
Value
TA = 25°C
Min.
Typ.
Max.
10
CIN
Input Capacitance
5.0
5
CPD
Power Dissipation
Capacitance (note
1)
5.0
7
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
10
Unit
Max.
10
pF
pF
1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/4 (per gate)
3/8
M74HC03
TEST CIRCUIT
CL = 50pF or equivalent (includes jig and probe capacitance)
RT = ZOUT of pulse generator (typically 50Ω)
WAVEFORM : PROPAGATION DELAY TIMES (f=1MHz; 50% duty cycle)
4/8
M74HC03
Plastic DIP-14 MECHANICAL DATA
mm.
inch
DIM.
MIN.
a1
0.51
B
1.39
TYP
MAX.
MIN.
TYP.
MAX.
0.020
1.65
0.055
0.065
b
0.5
0.020
b1
0.25
0.010
D
20
0.787
E
8.5
0.335
e
2.54
0.100
e3
15.24
0.600
F
7.1
0.280
I
5.1
0.201
L
Z
3.3
1.27
0.130
2.54
0.050
0.100
P001A
5/8
M74HC03
SO-14 MECHANICAL DATA
DIM.
mm.
MIN.
TYP
A
a1
inch
MAX.
MIN.
TYP.
1.75
0.1
0.068
0.2
a2
MAX.
0.003
0.007
1.65
0.064
b
0.35
0.46
0.013
0.018
b1
0.19
0.25
0.007
0.010
C
0.5
0.019
c1
45° (typ.)
D
8.55
8.75
0.336
0.344
E
5.8
6.2
0.228
0.244
e
1.27
0.050
e3
7.62
0.300
F
3.8
4.0
0.149
0.157
G
4.6
5.3
0.181
0.208
L
0.5
1.27
0.019
0.050
M
S
0.68
0.026
8° (max.)
PO13G
6/8
M74HC03
TSSOP14 MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MAX.
MIN.
TYP.
MAX.
1.2
A1
0.05
A2
0.8
b
0.047
0.15
0.002
0.004
0.006
1.05
0.031
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
4.9
5
5.1
0.193
0.197
0.201
E
6.2
6.4
6.6
0.244
0.252
0.260
E1
4.3
4.4
4.48
0.169
0.173
0.176
1
e
0.65 BSC
K
0°
L
0.45
A
0.60
0.0256 BSC
8°
0°
0.75
0.018
8°
0.024
0.030
A2
A1
b
e
K
c
L
E
D
E1
PIN 1 IDENTIFICATION
1
0080337D
7/8
M74HC03
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics
© 2001 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom
© http://www.st.com
8/8