STMICROELECTRONICS M74HC07

M74HC07
HEX BUFFER (OPEN DRAIN)
■
■
■
■
■
HIGH SPEED:
tPD = 6ns (TYP.) at VCC = 6V
LOW POWER DISSIPATION:
ICC = 1µA(MAX.) at TA=25°C
HIGH NOISE IMMUNITY:
VNIH = VNIL = 28 % VCC (MIN.)
WIDE OPERATING VOLTAGE RANGE:
VCC (OPR) = 2V to 6V
PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 07
DESCRIPTION
The M74HC07 is an high speed CMOS HEX
OPEN DRAIN BUFFER fabricated with silicon
gate C2MOS technology.
The internal circuit is composed of 2 stages
including buffer output, which enables high noise
immunity and stable output.
DIP
SOP
TSSOP
ORDER CODES
PACKAGE
TUBE
DIP
SOP
TSSOP
M74HC07B1R
M74HC07M1R
T&R
M74HC07RM13TR
M74HC07TTR
All inputs are equipped with protection circuits
against static discharge and transient excess
voltage.
PIN CONNECTION AND IEC LOGIC SYMBOLS
May 2003
1/10
M74HC07
INPUT AND OUTPUT EQUIVALENT CIRCUIT
PIN DESCRIPTION
PIN No
SYMBOL
1, 3, 5, 9, 11,
13
2, 4, 6, 8, 10,
12
7
NAME AND FUNCTION
1A to 6A
Data Inputs
1Y to 6Y
Data Outputs
GND
VCC
Ground (0V)
14
Positive Supply Voltage
TRUTH TABLE
A
Y
L
H
L
Z
Z : High Impedance
ABSOLUTE MAXIMUM RATINGS
Symbol
VCC
Parameter
Supply Voltage
Value
Unit
-0.5 to +7
V
-0.5 to VCC + 0.5
-0.5 to VCC + 0.5
V
DC Input Diode Current
± 20
mA
IOK
DC Output Diode Current
± 20
mA
IO
DC Output Current
VI
DC Input Voltage
VO
DC Output Voltage
IIK
ICC or IGND DC VCC or Ground Current
Power Dissipation
PD
Tstg
Storage Temperature
TL
Lead Temperature (10 sec)
V
± 25
mA
± 50
mA
500(*)
mW
-65 to +150
°C
300
°C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
(*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Parameter
Supply Voltage
Unit
2 to 6
V
VI
Input Voltage
0 to VCC
V
VO
Output Voltage
0 to VCC
V
Top
Operating Temperature
Input Rise and Fall Time
tr, tf
2/10
Value
-55 to 125
°C
VCC = 2.0V
0 to 1000
ns
VCC = 4.5V
0 to 500
ns
VCC = 6.0V
0 to 400
ns
M74HC07
DC SPECIFICATIONS
Test Condition
Symbol
VIH
VIL
VOL
II
IOZ
ICC
Parameter
High Level Input
Voltage
Low Level Input
Voltage
Low Level Output
Voltage
Input Leakage
Current
Output Leakage
Current
Quiescent Supply
Current
Value
TA = 25°C
VCC
(V)
Min.
2.0
4.5
6.0
2.0
4.5
6.0
Typ.
Max.
1.5
3.15
4.2
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
1.5
3.15
4.2
Unit
Max.
1.5
3.15
4.2
V
0.5
1.35
1.8
0.5
1.35
1.8
0.5
1.35
1.8
V
2.0
IO=20 µA
0.0
0.1
0.1
0.1
4.5
IO=20 µA
0.0
0.1
0.1
0.1
6.0
IO=20 µA
0.0
0.1
0.1
0.1
4.5
IO=4.0 mA
0.17
0.26
0.33
0.40
6.0
IO=5.2 mA
0.18
0.26
0.33
0.40
6.0
VI = VCC or GND
± 0.1
±1
±1
µA
6.0
VI = VIH or VIL
VO = VCC or GND
±0.5
±5
± 10
µA
6.0
VI = VCC or GND
1
10
20
µA
V
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
Test Condition
Symbol
tTHL
tPLZ
tPZL
Parameter
Output Transition
Time
Propagation Delay
Time
Propagation Delay
Time
TA = 25°C
VCC
(V)
2.0
4.5
6.0
2.0
4.5
6.0
2.0
4.5
6.0
Value
Min.
RL = 1 K Ω
RL = 1 K Ω
Typ.
Max.
30
8
7
10
7
6
17
7
5
75
15
13
90
18
15
90
18
15
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
95
19
16
115
23
20
115
23
20
Unit
Max.
110
22
19
135
27
23
135
27
23
ns
ns
ns
3/10
M74HC07
CAPACITIVE CHARACTERISTICS
Test Condition
Symbol
Parameter
CIN
Input Capacitance
COUT
Output
Capacitance
Power Dissipation
Capacitance (note
1)
CPD
VCC
(V)
Value
TA = 25°C
Min.
-40 to 85°C
-55 to 125°C
Min.
Min.
Max.
Unit
Typ.
Max.
5.0
5
10
5.0
3
pF
5.0
4
pF
10
Max.
10
pF
1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/6 (per gate)
TEST CIRCUIT
CL = 50pF or equivalent (includes jig and probe capacitance)
RT = ZOUT of pulse generator (typically 50Ω)
WAVEFORM : PROPAGATION DELAY TIME (f=1MHz; 50% duty cycle)
4/10
M74HC07
Plastic DIP-14 MECHANICAL DATA
mm.
inch
DIM.
MIN.
a1
0.51
B
1.39
TYP
MAX.
MIN.
TYP.
MAX.
0.020
1.65
0.055
0.065
b
0.5
0.020
b1
0.25
0.010
D
20
0.787
E
8.5
0.335
e
2.54
0.100
e3
15.24
0.600
F
7.1
0.280
I
5.1
0.201
L
Z
3.3
1.27
0.130
2.54
0.050
0.100
P001A
5/10
M74HC07
SO-14 MECHANICAL DATA
DIM.
mm.
MIN.
TYP
A
a1
inch
MAX.
MIN.
TYP.
1.75
0.1
0.068
0.2
a2
MAX.
0.003
0.007
1.65
0.064
b
0.35
0.46
0.013
0.018
b1
0.19
0.25
0.007
0.010
C
0.5
0.019
c1
45˚ (typ.)
D
8.55
E
5.8
8.75
0.336
6.2
0.228
0.344
0.244
e
1.27
0.050
e3
7.62
0.300
F
3.8
4.0
0.149
0.157
G
4.6
5.3
0.181
0.208
L
0.5
1.27
0.019
0.050
M
S
0.68
0.026
8 ˚ (max.)
PO13G
6/10
M74HC07
TSSOP14 MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MAX.
MIN.
TYP.
MAX.
1.2
A1
0.05
A2
0.8
b
0.047
0.15
0.002
0.004
0.006
1.05
0.031
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
4.9
5
5.1
0.193
0.197
0.201
E
6.2
6.4
6.6
0.244
0.252
0.260
E1
4.3
4.4
4.48
0.169
0.173
0.176
1
e
0.65 BSC
K
0˚
L
0.45
A
0.60
0.0256 BSC
8˚
0˚
0.75
0.018
8˚
0.024
0.030
A2
A1
b
e
K
c
L
E
D
E1
PIN 1 IDENTIFICATION
1
0080337D
7/10
M74HC07
Tape & Reel SO-14 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
MAX.
MIN.
330
13.2
TYP.
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
8/10
TYP
0.504
22.4
0.519
0.882
Ao
6.4
6.6
0.252
0.260
Bo
9
9.2
0.354
0.362
Ko
2.1
2.3
0.082
0.090
Po
3.9
4.1
0.153
0.161
P
7.9
8.1
0.311
0.319
M74HC07
Tape & Reel TSSOP14 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
TYP
MAX.
MIN.
330
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
13.2
TYP.
0.504
22.4
0.519
0.882
Ao
6.7
6.9
0.264
0.272
Bo
5.3
5.5
0.209
0.217
Ko
1.6
1.8
0.063
0.071
Po
3.9
4.1
0.153
0.161
P
7.9
8.1
0.311
0.319
9/10
M74HC07
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics
© 2003 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
© http://www.st.com
10/10