M74HC4066 QUAD BILATERAL SWITCH ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 7ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC = 1µA(MAX.) at TA=25°C LOW "ON" RESISTANCE: RON = 50Ω TYP. AT VCC = 9V, II/O = 100 µA WIDE OPERATING VOLTAGE RANGE VCC (OPR) = 2V TO 12V SINE WAVE DISTORTION: 0.042% at VCC = 4V f = 1KHz HIGH NOISE IMMUNITY: VNIH = V NIL = 28 % VCC (MIN.) PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 4066 DESCRIPTION The M74HC4066 is an high speed CMOS QUAD BILATERAL SWITCH fabricated with silicon gate C2MOS technology. DIP SOP TSSOP ORDER CODES PACKAGE TUBE DIP SOP TSSOP M74HC4066B1R M74HC4066M1R T&R M74HC4066RM13TR M74HC4066TTR The C input is provided to control the switch; the switch is on when the C input is held high and off when C is held low. PIN CONNECTION AND IEC LOGIC SYMBOLS July 2001 1/11 M74HC4066 LOGIC DIAGRAM PIN DESCRIPTION PIN No SYMBOL 1, 4, 8, 11 1 to 4 I/O 2, 3, 9, 10 1 to 4 O/I 13, 5, 6, 12 1C to 4C 7 14 GND VCC NAME AND FUNCTION Independent Inputs/Outputs Independent Outputs/ Inputs Enable Inputs (Active High) Ground (0V) Positive Supply Voltage TRUTH TABLE CONTROL SWITCH FUNCTION H L ON OFF ABSOLUTE MAXIMUM RATINGS Symbol Parameter VCC Supply Voltage Value Unit -0.5 to +13 V VIN DC Input Voltage -0.5 to VCC + 0.5 V VI/O DC Input/Output Voltage IOK Control Input DC Diode Current -0.5 to VCC + 0.5 ± 20 mA IIOK I/O DC Diode Current ± 20 mA DC Output Source Sink Current Per Output Pin ± 25 mA IO ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) V ± 50 mA 500(*) mW -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C RECOMMENDED OPERATING CONDITIONS Symbol Parameter Value Unit VCC Supply Voltage 2 to 12 V VIN Input Voltage (Control) 0 to VCC V VI/O I/O Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C Input Rise and Fall Time tr, tf 2/11 VCC = 2.0V 0 to 1000 VCC = 4.5V 0 to 500 VCC = 6.0V 0 to 400 VCC = 10.0V 0 to 250 ns M74HC4066 DC SPECIFICATIONS Test Condition Symbol VIHC VILC RON Parameter High Level Control Input Voltage Low Level Control Input Voltage ON Resistance ∆RON Difference of ON Resistance between switches IOFF Input/Output Leakage Current (SWITCH OFF) IIZ Switch Input Leakage Current (SWITCH ON, OUTPUT OPEN) Control Input Current Quiescent Supply Current IIN ICC TA = 25°C VCC (V) Min. 2.0 4.5 9.0 12.0 2.0 4.5 9.0 12.0 4.5 VI = VIHC 9.0 VI/O = VCC to GND II/O ≤ 1mA 12.0 4.5 VI = VIHC 9.0 VI/O = VCC or GND II/O ≤ 1mA 12.0 4.5 VI = VIHC 9.0 VI/O = VCC or GND II/O ≤ 1mA 12.0 VOS = VCC or GND 12.0 VIS = VCC or GND VIN = VILC 12.0 6.0 6.0 9.0 12.0 Value Typ. Max. 1.5 3.15 6.3 8.4 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 3.15 6.3 8.4 96 55 45 70 50 45 10 5 5 0.5 1.35 2.7 3.6 170 85 80 100 75 70 Max. 1.5 3.15 6.3 8.4 0.5 1.35 2.7 3.6 200 100 90 130 95 90 Unit V 0.5 1.35 2.7 3.6 250 150 120 160 115 110 V Ω Ω ± 0.1 ±1 ±2 µA VOS = VCC or GND VIN = VIHC ± 0.1 ±1 ±2 µA VI = VCC or GND ± 0.1 ±1 ±1 µA VI = VCC or GND 1 4 8 10 40 80 20 80 160 µA 3/11 M74HC4066 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol ΦI/O tPZL tPZH tPLZ tPHZ Parameter Value TA = 25°C VCC (V) Min. Phase Difference Between Input and Output 2.0 4.5 9.0 12.0 Output Enable Time 2.0 4.5 9.0 12.0 Output Disable 2.0 Time 4.5 9.0 12.0 Maximum Control 2.0 Input Frequency 4.5 9.0 12.0 RL = 1KΩ RL = 1KΩ RL = 1KΩ CL = 15 pF VOUT = 1/2 VCC Typ. Max. 10 4 3 3 18 8 6 6 20 10 8 8 30 30 30 30 50 10 8 7 100 20 12 12 115 23 20 18 -40 to 85°C -55 to 125°C Min. Min. Max. 65 13 10 9 125 25 22 18 145 29 25 22 Unit Max. 75 15 13 10 150 30 27 25 175 35 30 27 ns ns ns MHz CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter VCC (V) Value TA = 25°C Min. Typ. Max. 10 -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. CIN Input Capacitance 5 CI/O Switch Terminal Capacitance Feed Through Capacitance Power Dissipation Capacitance (note 1) 6 pF 0.5 pF 15 pF CIOS CPD 10 10 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC 4/11 M74HC4066 ANALOG SWITCH CHARACTERISTICS (GND = 0V;TA = 25°C) Symbol Parameter Sine Wave Distortion (THD) fMAX Frequency Response (Switch ON) Feed through Attenuation (Switch OFF) Crosstalk (Control Input to Signal Output) Crosstalk (Between Any Switches) Test Condition VCC (V) VIN (Vp-p) 4.5 9.0 4.5 9.0 4 8 Value Unit Typ. fIN = 1 KHz RL = 10 KΩ, CL = 50 pF Adjust fIN voltage to obtain 0 dBm at VOS. Increase fIN Frequency until dB meter reads -3dB RL = 50Ω, CL = 10 pF 0.05 0.04 200 200 MHz % 4.5 9.0 VIN is centered at VCC/2. Adjust input for 0 dBm RL = 600Ω CL = 50 pF, fIN = 1MHz sine wave -60 -60 dB 4.5 9.0 RL = 600Ω, CL = 50 pF, fIN = 1MHz square wave (tr = tf =6ns) 60 100 mV 4.5 9.0 Adjust VIN to Obtain 0 dBmat input RL = 600Ω, CL = 50 pF, fIN = 1MHz sine wave -60 -60 dB 5/11 M74HC4066 SWITCHING CARACTERISTICS TEST CIRCUIT CROSSTALK (control to output) CROSSTALK BETWEEN ANY TWO SWITCHES BANDWIDTH AND FEEDTHROUGH ATTENUATION MAXIMUM CONTROL FREQUENCY 6/11 M74HC4066 CHANNEL RESISTANCE (RON) ICC (Opr.) 7/11 M74HC4066 Plastic DIP-14 MECHANICAL DATA mm. inch DIM. MIN. a1 0.51 B 1.39 TYP MAX. MIN. TYP. MAX. 0.020 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 I 5.1 0.201 L Z 3.3 1.27 0.130 2.54 0.050 0.100 P001A 8/11 M74HC4066 SO-14 MECHANICAL DATA DIM. mm. MIN. TYP A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.2 a2 MAX. 0.003 0.007 1.65 0.064 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.019 c1 45° (typ.) D 8.55 8.75 0.336 0.344 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.149 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.019 0.050 M S 0.68 0.026 8° (max.) PO13G 9/11 M74HC4066 TSSOP14 MECHANICAL DATA mm. inch DIM. MIN. TYP A MAX. MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.9 5 5.1 0.193 0.197 0.201 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0° L 0.45 A 0.60 0.0256 BSC 8° 0° 0.75 0.018 8° 0.024 0.030 A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080337D 10/11 M74HC4066 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 11/11