VNH100N04 ”OMNIFET”: FULLY AUTOPROTECTED POWER MOSFET TARGET DATA TYPE V clamp R DS(on) I lim VNH100N04 42 V 0.012 Ω 100 A ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ LINEAR CURRENT LIMITATION THERMAL SHUT DOWN SHORT CIRCUIT PROTECTION INTEGRATED CLAMP LOW CURRENT DRAWN FROM INPUT PIN DIAGNOSTIC FEEDBACK THROUGH INPUT PIN ESD PROTECTION DIRECT ACCESS TO THE GATE OF THE POWER MOSFET (ANALOG DRIVING) COMPATIBLE WITH STANDARD POWER MOSFET STANDARD TO-218 PACKAGE DESCRIPTION The VNH100N04 is a monolithic device made using SGS-THOMSON Vertical Intelligent Power M0 Technology, intended for replacement of standard power MOSFETS in DC to 50 KHz applications. Buit-in thermal shut-down, linear TO-218 current limitation and overvoltage clamp protect the chip in harsh enviroments. Fault feedback can be detected by monitoring the voltage at the input pin. BLOCK DIAGRAM September 1994 1/7 VNH100N04 ABSOLUTE MAXIMUM RATING Symbol Parameter Value Unit Internally Clamped V VD S Drain-source Voltage (V in = 0) V in Input Voltage 18 V ID Drain Current Internally Limited A IR Reverse DC Output Current -50 A 2000 V V esd P tot Tj Tc T stg Electrostatic Discharge (C= 100 pF, R=1.5 KΩ) o Total Dissipation at Tc = 25 C 208 Operating Junction Temperature Case Operating Temperature W Internally Limited o C Internally Limited o C -55 to 150 o C Storage Temperature THERMAL DATA R thj-cas e Rthj- amb Thermal Resistance Junction-case Thermal Resistance Junction-ambient Max Max o 0.6 30 o C/W C/W ELECTRICAL CHARACTERISTICS (Tcase = 25 oC unless otherwise specified) OFF Symbol Parameter Test Conditions Min. Typ. Max. Unit 42 48 V V CLAMP Drain-source Clamp Voltage I D = 30 A V in = 0 36 V CLTH Drain-source Clamp Threshold Voltage I D = 2 mA V in = 0 35 V I NC L Input-Source Reverse Clamp Voltage I in = -1 mA I DS S Zero Input Voltage Drain Current (V in = 0) V DS = 13 V V DS = 25 V I ISS Supply Current from Input Pin V DS = 0 V V -1 V in = 10 V -0.3 V 50 200 µA µA 250 500 µA Typ. Max. Unit 3 V 0.012 0.015 Ω Ω Max. Unit ON (∗) Symbol VI S(th) R DS( on) Parameter Test Conditions Input Threshold Voltage V DS = V in ID = 1 mA Static Drain-source On Resistance V in = 10 V I D = 30 A V in = 5 V ID = 30 A Min. 0.8 DYNAMIC Symbol gfs (∗) C oss 2/7 Parameter Test Conditions Forward Transconductance V DS = 13 V ID = 30 A Output Capacitance V DS = 13 V f = 1 MHz Min. Typ. 40 Vin = 0 1800 S 3000 pF VNH100N04 ELECTRICAL CHARACTERISTICS (continued) SWITCHING Symbol Parameter Test Conditions Typ. Max. Unit 100 400 900 400 TBD TBD TBD TBD ns ns ns ns Id = 30 A Rgen = 10 Ω TBD TBD TBD TBD ns ns ns ns Id = 30 A Rgen = 1000 Ω TBD TBD TBD TBD µs µs µs µs t d(on) tr t d(off ) tf Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time V DD = 15 V V gen = 10 V (see figure 3) Id = 30 A Rgen = 10 Ω t d(on) tr t d(off ) tf Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time V DD = 15 V V gen = 10 V T j = 125 o C (see figure 3) t d(on) tr t d(off ) tf Turn-on Delay Time Rise Time Turn-off Delay Time Fall Time V DD = 15 V V gen = 10 V (see figure 3) Turn-on Current Slope V DD = 15 V V in = 10 V Total Gate Charge V DD = 12 V (di/dt) on Qg Min. ID = 30 A ID = 30 A V in = 10 V TBD A/µs TBD nC SOURCE DRAIN DIODE Symbol V S D (∗) t rr Q rr I RRM Parameter Test Conditions Forward On Voltage I SD = 30 A Reverse Recovery Time Reverse Recovery Charge Reverse Recovery Current I SD = 30 A di/dt = 100 A/µs V DD = V T j = 150 o C (see test circuit, figure 5) Min. Typ. V in = 0 Max. Unit TBD V TBD ns TBD µC TBD A PROTECTION Symbol Parameter Test Conditions V DS = 13 V Min. Typ. Max. Unit 70 100 140 A TBD µs 190 o C o C I lim Drain Current Limit V in = 10 V tdlim Step Response Current Limit V in = 10 V V D S = 13V T jsh Overtemperature Shutdown 150 T jrs Overtemperature Reset 135 Igf Fault Sink Current V in = 10 V E as Single Pulse Avalanche Energy starting T j = 25 o C V DD = 20 V V in = 10 V Rgen = 1 KΩ L = mH V DS = 13 V 170 50 TBD mA J (∗) Pulsed: Pul se duration = 300 µs, duty cycle 1.5 % 3/7 VNH100N04 PROTECTION FEATURES During normal operation, the Input pin is electrically connected to the gate of the internal power MOSFET. The device then behaves like a standard power MOSFET and can be used as a switch from DC to 50 KHz. The only difference from the user’s standpoint is that a small DC current (Iiss) flows into the Input pin in order to supply the internal circuitry. The device integrates: – OVERVOLTAGE CLAMP PROTECTION: internally set at 42V, along with the rugged avalanche characteristics of the Power MOSFET stage give this device unrivalled ruggedness and energy handling capability. This feature is mainly important when driving inductive loads. – LINEAR CURRENT LIMITER CIRCUIT: limits the drain current Id to Ilim whatever the Input pin voltage. When the current limiter is active, the device operates in the linear region, so power dissipation may exceed the capability of the heatsink. Both case and junction temperatures increase, and if this phase lasts long enough, junction temperature may reach the overtemperature threshold Tjsh. 4/7 – OVERTEMPERATURE AND SHORT CIRCUIT PROTECTION: these are based on sensing the chip temperature and are not dependent on the input voltage. The location of the sensing element on the chip in the power stage area ensures fast, accurate detection of the junction temperature. Overtemperature cutout occurs in the range 150 to 190oC, a typical value being o 170 C. The device is automatically restarted when the chip temperature falls below 135oC. – STATUS FEEDBACK: In the case of an overtemperature fault condition, a Status Feedback is provided through the Input pin. The internal protection circuit disconnects the input from the gate and connects it instead to ground via an equivalent resistance of 200 Ω. The failure can be detected by monitoring the voltage at the Input pin, which will be close to ground potential. Additional features of this device are ESD protection according to the Human Body model and the ability to be driven from a TTL Logic circuit (with a small increase in RDS(on)). VNH100N04 Fig. 1: Unclamped Inductive Load Test Circuits Fig. 2: Unclamped Inductive Waveforms Fig. 3: Switching Times Test Circuits For Resistive Load Fig. 4: Input Charge Test Circuit Fig. 5: Test Circuit For Inductive Load Switching And Diode Recovery Times Fig. 6: Waveforms 5/7 VNH100N04 TO-218 (SOT-93) MECHANICAL DATA mm DIM. MIN. inch TYP. MAX. MIN. TYP. MAX. A 4.7 4.9 0.185 0.193 C 1.17 1.37 0.046 0.054 D 2.5 0.098 E 0.5 0.78 0.019 0.030 F 1.1 1.3 0.043 0.051 G 10.8 11.1 0.425 0.437 H 14.7 15.2 0.578 0.598 L2 – 16.2 – 0.637 L3 18 L5 0.708 3.95 4.15 L6 0.155 0.163 31 1.220 – 12.2 – 0.480 Ø 4 4.1 0.157 0.161 D C A E R L6 L5 H G L3 L2 F Ø R 6/7 1 2 3 P025A VNH100N04 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 7/7