MIG400J2CSB1W TOSHIBA Intelligent Power Module Silicon N Channel IGBT MIG400J2CSB1W (600V/400A 2in1) High Power Switching Applications Motor Control Applications · Integrates inverter power circuits and control circuits (IGBT drive unit, units for protection against short-circuit current, overcurrent, undervoltage and overtemperature) into a single package. · The electrodes are isolated from the case. · Low thermal resistance · VCE (sat) = 1.9 V (typ.) · UL recognized: File No.E87989 · Weight: 278 g (typ.) Equivalent Circuit 1 2 3 4 5 6 7 8 FO GND IN VD FO GND IN VD GND VS GND VS OUT OUT E2 C1 C2/E1 1. FO (L) 2. GND (L) 3. IN (L) 4. VD (L) 5. FO (H) 6. GND (H) 7. IN (H) 8. VD (H) 1 2002-07-22 MIG400J2CSB1W Package Dimensions: TOSHIBA 2-108H1A Unit: mm 1. FO (L) 2. GND (L) 3. IN (L) 4. VD (L) 5. FO (H) 6. GND (H) 7. IN (H) 8. VD (H) 2 2002-07-22 MIG400J2CSB1W Signal Terminal Layout Unit: mm 1. FO (L) 2. GND (L) 3. IN (L) 4. VD (L) 5. FO (H) 6. GND (H) 7. IN (H) 8. VD (H) 3 2002-07-22 MIG400J2CSB1W Maximum Ratings (Tj = 25°C) Stage Characteristics Condition Supply voltage Symbol Rating Unit P-N power terminal VCC 450 V ¾ VCES 600 V IC 400 A Collector-emitter voltage Inverter Collector current Tc = 25°C, DC Forward current Tc = 25°C, DC IF 400 A Collector power dissipation Tc = 25°C PC 2190 W Tj 150 °C ¾ Junction temperature Control supply voltage VD-GND terminal VD 20 V Input voltage IN-GND terminal VIN 20 V Fault output voltage FO-GND terminal VFO 20 V Fault output current FO sink current IFO 10 mA Control Operating temperature ¾ Tc -20~+100 °C Storage temperature ¾ Tstg -40~+125 °C VISO 2500 V ¾ 3 N･m Module Isolation voltage AC 1 min Screw torque M5 Electrical Characteristics 1. Inverter stage Characteristics Collector cut-off current Collector-emitter saturation voltage Forward voltage Symbol ICEX VCE (sat) VF Test Condition VCE = 600 V VD = 15 V IC = 400 A VIN = 15 V ® 0 V Switching time trr ¾ ¾ 1 ¾ ¾ 10 Tj = 25°C 1.6 1.9 2.3 Tj = 125°C ¾ 2.1 ¾ ¾ 2.3 2.7 ¾ 2.0 3.0 ¾ 0.4 ¾ ¾ 0.2 ¾ ¾ 1.5 2.5 ¾ 0.25 ¾ VCC = 300 V, IC = 400 A VD = 15 V, VIN = 15 V « 0 V Tj = 25°C, Inductive load (Note 1) tc (off) Max Tj = 25°C IF = 400 A, Tj = 25°C toff Typ. Tj = 125°C ton tc (on) Min Unit mA V V ms Note 1: Switching time test circuit & timing chart 4 2002-07-22 MIG400J2CSB1W 2. Control stage (Tj = 25°C) Characteristics Control circuit current Symbol High side ID (H) Low side ID (L) Input on signal voltage VIN (on) Input off signal voltage VIN (off) Protection IFO (on) Normal IFO (off) Fault output current Test Condition VD = 15 V VD = 15 V Min Typ. Max ¾ 13 17 ¾ 13 17 1.4 1.6 1.8 2.2 2.5 2.8 ¾ 10 12 ¾ ¾ 0.1 Unit mA V VD = 15 V mA Overcurrent protection trip Inverter level OC VD = 15 V, Tj < = 125°C 640 ¾ ¾ A Short-circuit protection trip level SC VD = 15 V, Tj < = 125°C 640 ¾ ¾ A ¾ 5 ¾ ms 110 118 125 ¾ 98 ¾ 11.0 12.0 12.5 12.0 12.5 13.0 1 2 3 ms Min Typ. Max Unit IGBT ¾ ¾ 0.057 FRD ¾ ¾ 0.130 Compound is applied ¾ 0.017 ¾ Inverter Overcurrent cut-off time toff (OC) Overtemperature protection Trip level Reset level OTr Control supply under voltage protection Trip level UV Reset level UVr VD = 15 V OT Case temperature Fault output pulse width tFO ¾ VD = 15 V °C V 3. Thermal resistance (Tc = 25°C) Characteristics Junction to case thermal resistance Case to fin thermal resistance Symbol Rth (j-c) Rth (c-f) Test Condition 5 °C/W °C/W 2002-07-22 MIG400J2CSB1W Switching Time Test Circuit Intelligent power module TLP559 C1 VD 0.1 mF 15 kW OUT IN VS 68 mF 15 V GND GND C2/E1 VCC VD IF = 16 mA 0.1 mF 15 kW OUT IN PG VS 68 mF 15 V GND E2 GND Timing Chart Input pulse 15 V VIN Waveform 2.5 V 1.6 V 0 90% Irr Irr IC Waveform 90% VCE Waveform 10% toff 10% 10% tc (off) ton 6 20% Irr trr 10% tc (on) 2002-07-22 MIG400J2CSB1W 4. Recommended conditions for application Characteristics Supply voltage Symbol VCC Test Condition P-N power terminal Control supply voltage VD VD-GND signal terminal Carrier frequency fc PWM control Dead time Switching time test circuit tdead (Note 2) Min Typ. Max Unit ¾ 300 400 V 13.5 15 16.5 V ¾ ¾ 20 kHz 5 ¾ ¾ ms Note 2: The table lists Dead time requirements for the module input, excluding photocoupler delays. When specifying dead time requirements for the photocoupler input, please add photocoupler delays to the dead time given above. Dead Time Timing Chart 15 V VIN Waveform 0 15 V VIN Waveform 0 tdead tdead 7 2002-07-22 MIG400J2CSB1W IC – VCE IC – VCE 800 800 700 VD = 15 V (A) VD = 13 V 600 IC VD = 17 V 500 Collector current (A) 500 Collector current 600 IC 700 400 300 200 100 0 0 1 1.5 2 2.5 Collector-emitter voltage 3 VCE 3.5 VD = 13 V VD = 15 V 400 300 200 100 Common emitter Tj = 25°C 0.5 VD = 17 V 0 0 4 (V) Common emitter Tj = 125°C 0.5 1 1.5 2 2.5 Collector-emitter voltage Switching time – IC 3 VCE ton toff (ms) tc (on) Switching time (ms) Switching time 1 tc (off) 0.1 Tj = 25°C VCC = 300 V VD = 15 V L-LOAD 0.01 100 0 200 300 Collector current IC toff 1 tc (on) tc (off) 0.1 Tj = 125°C VCC = 300 V VD = 15 V L-LOAD 0.01 500 400 0 100 (A) IF – VF IC 500 400 (A) trr, Irr – IF Peak reverse recovery current Irr (A) Reverse recovery time trr (´ 10 ns) (A) 300 1000 700 Forward current IF 200 Collector current 800 400 300 200 Common cathode : Tj = 25°C 100 : Tj = 125°C 0 0 (V) 10 ton 500 4 Switching time – IC 10 600 3.5 0.5 1 1.5 2 Forward voltage 2.5 3 3.5 Irr 100 Common cathode : Tj = 25°C : Tj = 125°C 1 0 4 VF (V) trr 10 100 200 Forward current 8 300 400 500 IF (A) 2002-07-22 MIG400J2CSB1W ID – fc OC – Tc 80 (mA) 800 60 ID 700 600 Control circuit current Over current protection trip level OC (A) 900 500 400 300 200 40 20 100 VD = 15 V Tj = 25°C VD = 15 V 0 0 0 25 75 50 100 Case temperature Tc 125 150 0 (°C) 5 Rth (t) – tw Reverse bias SOA Transient thermal resistance Rth (t) (°C/W) OC (A) IC Collector current 640 480 400 320 240 160 80 Tj < = 125°C VD = 15 V 0 0 100 200 300 400 600 500 Collector-emitter voltage VCE 700 1 0.3 Diode stage 0.1 0.03 Transistor stage 0.01 0.003 0.001 Tc = 25°C 0.0003 0.001 0.01 (V) Eon – IC 1 10 tw (s) Eoff – IC 100 Eoff (mJ) 10 Turn off loss Eon (mJ) Turn on loss 0.1 Pulse width 100 1 VCC = 300 V VD = 15 V L-LOAD : Tj = 25°C : Tj = 125°C 0.1 0 25 20 Carrier frequency fc (kHz) 720 560 15 10 100 200 300 Collector current IC 400 10 1 VCC = 300 V VD = 15 V L-LOAD : Tj = 25°C : Tj = 125°C 0.1 0 500 (A) 100 200 Collector current 9 300 IC 400 (A) 2002-07-22 MIG400J2CSB1W RESTRICTIONS ON PRODUCT USE 000707EAA · TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc.. · The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. · The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. · The information contained herein is subject to change without notice. 10 2002-07-22