AIMTEC AMER3

Series AMER3/4-KZ
up to 700mA | AC-DC LED driver
FEATURES:
•
•
•
•
AC-DC Constant Current LED Driver
Universal Input: 90-264VAC, 47-63Hz
Short circuit protection
RoHS compliant
•
•
•
•
Waterproof IP67
Over current protection
Over voltage protection
Low output Ripple
Models
Single output
Model
Max Output
Power (W) *
Output Voltage
Range (V)
Output Current
(mA)
Input Voltage
(VAC/Hz)
Efficiency
(%)
4.2
2.9
2 - 12
2-4
325 ±25
700 ±30
90-264/ 47-63
90-264/ 47-63
60
60
AMER4-1230KZ
AMER3-0470KZ
* Exceeding the maximum output power will permanently damage the converter
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Input Specifications
Parameters
Conditions
Typical
115V
220V
230V
115V
220V
90-264
10
20
0.25
0.01
0.03
0.7
Voltage range
Inrush current <2ms
Leakage current
AC current
No-load consumption
External fuse
Maximum
Units
VAC
A
mA
A
W
250V/1.5A
Output Specifications
Parameters
Current accuracy
Line regulation
Load regulation
Ripple & Noise
Hold-up time (min)
Conditions
Typical
Maximum
Units
LL-HL
2V to 100% load
20MHz Bandwidth
100% load
±10
±5
±10
100
3
5
%
%
%
mV p-p
ms
Conditions
Typical
Maximum
Units
5MA/60S
1500
1500
1500
Conditions
Typical
Isolation Specifications
Parameters
Tested I/O voltage
Input FG
Output FG
VAC
VAC
VAC
General Specifications
Parameters
Switching frequency
Over current protection
Over voltage protection
Short circuit protection
Operating temperature *
Temperature Rise
Storage temperature
Temperature coefficient
Cooling
Humidity
Case material
www.aimtec.com
F 052.1e R1.C
Maximum
100
115
Zener Diode Clamp
Auto-Recovery
-30 to +55
25
-40 to +80
0.05
Free Air Convection
Units
KHz
%
o
C
C
o
C
% / oC
o
95
% RH
Aluminum
Tel: +1 514 620 2722
1 of 2
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AMER3/4-KZ
up to 700mA | AC-DC LED driver
General Specifications (continued)
Parameters
Conditions
Weight
Dimensions (L X H X W)
Switching frequency
MTBF
Typical
Maximum
Units
22
0.98 x 0.98 x 0.98 inches 25.00 x 25.00 x 25.00 mm
100
30 000 hrs (MIL-HDBK-217 F at +25 oC)
g
KHz
* NOTE: Converters do not have Over Temperature Protection and will be damaged if their maximum case temperature is
exceeded.
Safety Specifications
Parameters
Agency approvals
Standards
CE
GB195110.1-2004/IEC61347-1:2003, EN55015, EN61000, EN61547
Dimensions
25.00
(0.98)
25.00
(0.98)
End View
25.00
(0.98)
25.00
(0.98)
Cable is 18AWG at 10cm
Cable is 18AWG at 10cm
Side View
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 052.1e R1.C
Tel: +1 514 620 2722
2 of 2
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only