LINER LT6203

Electrical Specifications Subject to Change
LTC2379-18
18-Bit, 1.6Msps, Low Power
SAR ADC with 101dB SNR
FEATURES
DESCRIPTION
n
The LTC®2379-18 is a low noise, low power, high speed
18-bit successive approximation register (SAR) ADC.
Operating from a 2.5V supply, the LTC2379-18 has a ±
VREF fully differential input range with VREF ranging from
2.5V to 5.1V. The LTC2379-18 consumes only 18mW
and achieves ±2LSB INL maximum, no missing codes at
18-bits with 101dB SNR.
n
n
n
n
n
n
n
n
n
n
n
n
n
n
1.6Msps Throughput Rate
±2LSB INL (Max)
Guaranteed 18-Bit No Missing Codes
Low Power: 18mW at 1.6Msps, 18μW at 1.6ksps
101dB SNR (typ) at fIN = 2kHz
Digital Gain Compression (DGC)
Guaranteed Operation to 125°C
2.5V Supply
Fully Differential Input Range ±VREF
VREF Input Range from 2.5V to 5.1V
No Pipeline Delay, No Cycle Latency
1.8V to 5V I/O Voltages
SPI-Compatible Serial I/O with Daisy-Chain Mode
Internal Conversion Clock
16-pin MSOP and 4mm × 3mm DFN Packages
The LTC2379-18 has a high speed SPI-compatible serial interface that supports 1.8V, 2.5V, 3.3V and 5V logic
while also featuring a daisychain mode. The fast 1.6Msps
throughput with no cycle latency makes the LTC2379-18
ideally suited for a wide variety of high speed applications.
An internal oscillator sets the conversion time, easing external timing considerations. The LTC2379-18 automatically
powers down between conversions, leading to reduced
power dissipation that scales with the sampling rate.
APPLICATIONS
n
n
n
n
n
n
The LTC2379-18 offers a digital gain compression (DGC)
feature that allows a full-scale input to be achieved with
inputs that swing between 10% and 90% of the ±VREF
analog input range. This allows the input buffer amplifier to be operated from a single positive supply without
headroom issues, resulting in a lower power system.
Medical Imaging
High Speed Data Acquisition
Portable or Compact Instrumentation
Industrial Process Control
Low Power Battery-Operated Instrumentation
ATE
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear
Technology Corporation. All other trademarks are the property of their respective owners.
TYPICAL APPLICATION
32k Point FFT fS = 1.6Msps, fIN = 2kHz
2.5V
0
1.8V TO 5V
SNR = 101.2dB
THD = –120dB
SINAD = 101.1dB
SFDR = 121dB
–20
10μF
+
20Ω
0V
0V
IN+
LTC2379-18
3300pF
VREF
–
OVDD
VDD
3300pF
IN–
20Ω
3300pF
REF
GND
CHAIN
RDL/SDI
SDO
SCK
BUSY
CNV
REF/DGC
2.5V TO 5.1V
237918 TA01
47μF
(X5R, 0805 SIZE)
SAMPLE CLOCK
VREF
AMPLITUDE (dBFS)
VREF
–40
–60
–80
–100
–120
–140
–160
–180
0
100 200 300 400 500 600 700 800
FREQUENCY (kHz)
237918 TA02
237918p
1
LTC2379-18
ABSOLUTE MAXIMUM RATINGS
(Notes 1, 2)
Supply Voltage (VDD) ...............................................2.8V
Supply Voltage (OVDD) ................................................6V
Reference Input (REF).................................................6V
Analog Input Voltage (Note 3)
IN+, IN– ......................... (GND –0.3V) to (REF + 0.3V)
REF/DGC Input (Note 3) .... (GND –0.3V) to (REF + 0.3V)
Digital Input Voltage
(Note 3) ........................... (GND –0.3V) to (OVDD + 0.3V)
Digital Output Voltage
(Note 3) ........................... (GND –0.3V) to (OVDD + 0.3V)
Power Dissipation .............................................. 500mW
Operating Temperature Range
LTC2379C ................................................ 0°C to 70°C
LTC2379I .............................................–40°C to 85°C
LTC2379H .......................................... –40°C to 125°C
Storage Temperature Range .................. –65°C to 150°C
PIN CONFIGURATION
TOP VIEW
CHAIN
1
VDD
2
GND
3
+
4
IN–
5
GND
6
REF
7
REF/DGC
8
IN
16 GND
15 OVDD
17
GND
TOP VIEW
CHAIN
VDD
GND
IN+
IN–
GND
REF
REF/DGC
14 SDO
13 SCK
12 RDL/SDI
11 BUSY
10 GND
9 CNV
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
GND
OVDD
SDO
SCK
RDL/SDI
BUSY
GND
CNV
MS PACKAGE
16-LEAD PLASTIC MSOP
TJMAX = 150°C, θJA = 110°C/W
DE PACKAGE
16-LEAD (4mm × 3mm) PLASTIC DFN
TJMAX = 150°C, θJA = 43°C/W
EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC2379CMS-18#PBF
LTC2379CMS-18#TRPBF
237918
16-Lead Plastic MSOP
0°C to 70°C
LTC2379IMS-18#PBF
LTC2379IMS-18#TRPBF
237918
16-Lead Plastic MSOP
–40°C to 85°C
LTC2379HMS-18#PBF
LTC2379HMS-18#TRPBF
237918
16-Lead Plastic MSOP
–40°C to 125°C
LTC2379CDE-18#PBF
LTC2379CDE-18#TRPBF
23798
16-Lead (4mm × 3mm) Plastic DFN
0°C to 70°C
LTC2379IDE-18#PBF
LTC2379IDE-18#TRPBF
23798
16-Lead (4mm × 3mm) Plastic DFN
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
237918p
2
LTC2379-18
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
CONDITIONS
VIN+
Absolute Input Range (IN+)
MIN
(Note 5)
l
VIN –
Absolute Input Range (IN–)
(Note 5)
l
VIN+ – VIN–
Input Differential Voltage Range
VIN = VIN+ – VIN–
l
VCM
Common-Mode Input Range
l
VREF/2–
0.05
IIN
Analog Input Leakage Current
l
CIN
Analog Input Capacitance
CMRR
Input Common Mode Rejection Ratio
TYP
MAX
UNITS
VREF
V
–0.05
VREF
V
–VREF
+VREF
V
VREF/2+
0.05
V
±1
μA
–0.05
Sample Mode
Hold Mode
VREF/2
45
5
pF
pF
TBD
dB
CONVERTER CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL PARAMETER
CONDITIONS
MIN
TYP
MAX
Resolution
18
Bits
No Missing Codes
l
18
Bits
l
–2
±1
2
LSB
LSB
Transition Noise
0.8
(Note 6)
LSBRMS
INL
Integral Linearity Error
DNL
Differential Linearity Error
l
–1
±0.4
1
Bipolar Zero-Scale Error
l
–6
±0.25
6
BZE
(Note 7)
Bipolar Zero-Scale Error Drift
FSE
UNITS
l
Bipolar Full-Scale Error
3
(Note 7)
l
–14
Bipolar Full-Scale Error Drift
±3
LSB
mLSB/°C
14
±0.1
LSB
ppm/°C
DYNAMIC ACCURACY
The l denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at TA = 25°C and AIN = –1dBFS. (Notes 4, 8)
SYMBOL PARAMETER
CONDITIONS
SINAD
fIN = 2kHz
Signal-to-(Noise + Distortion) Ratio
MIN
TYP
l
98
100.5
dB
98
101
99
96
dB
dB
dB
–115
–118
TBD
TBD
dB
dB
dB
SNR
Signal-to-Noise Ratio
fIN = 2kHz, VREF = 5V
fIN = 2kHz, VREF = 5V, REF/DGC = GND
fIN = 2kHz, VREF = 2.5V
l
THD
Total Harmonic Distortion
fIN = 2kHz, VREF = 5V
fIN = 2kHz, VREF = 5V, REF/DGC = GND
fIN = 2kHz, VREF = 2.5V
l
Spurious Free Dynamic Range
fIN = 2kHz
SFDR
MAX
UNITS
120
dB
–3dB Input Bandwidth
TBD
MHz
Aperture Delay
TBD
ns
TBD
ps
200
ns
Aperture Jitter
Transient Response
Full-Scale Step
237918p
3
LTC2379-18
REFERENCE INPUT
The l denotes the specifications which apply over the full operating temperature range, otherwise
specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
CONDITIONS
VREF
Reference Voltage
(Note 5)
l
MIN
IREF
Reference Input Current
(Note 9)
l
VIHDGC
High Level Input Voltage REF/DGC Pin
l
VILDGC
Low Level Input Voltage REF/DGC Pin
l
TYP
2.5
1
MAX
UNITS
5.1
V
1.2
mA
0.8VREF
V
0.2VREF
V
DIGITAL INPUTS AND DIGITAL OUTPUTS
The l denotes the specifications which apply over the
full operating temperature range, otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL PARAMETER
CONDITIONS
MIN
VIH
High Level Input Voltage
l
VIL
Low Level Input Voltage
l
l
TYP
MAX
UNITS
0.8 • OVDD
V
0.2 • OVDD
V
10
μA
IIN
Digital Input Current
CIN
Digital Input Capacitance
VOH
High Level Output Voltage
IO = –500 μA
l
VOL
Low Level Output Voltage
IO = 500 μA
l
IOZ
Hi-Z Output Leakage Current
VOUT = 0V to OVDD
l
ISOURCE
Output Source Current
VOUT = 0V
–10
mA
ISINK
Output Sink Current
VOUT = OVDD
10
mA
VIN = 0V to OVDD
–10
5
pF
OVDD – 0.2
V
–10
0.2
V
10
μA
POWER REQUIREMENTS
The l denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
CONDITIONS
VDD
Supply Voltage
OVDD
Supply Voltage
IVDD
IOVDD
IPD
IPD
Supply Current
Supply Current
Power Down Mode
Power Down Mode
1.6Msps Sample Rate
1.6Msps Sample Rate (CL = 20pF)
Conversion Done (IVDD + IOVDD + IREF)
Conversion Done (IVDD + IOVDD + IREF, H-Grade)
PD
Power Dissipation
Power Down Mode
Power Down Mode
1.6Msps Sample Rate
Conversion Done (IVDD + IOVDD + IREF)
Conversion Done (IVDD + IOVDD + IREF, H-Grade)
MIN
TYP
MAX
UNITS
l
2.375
2.5
2.625
V
l
1.71
l
l
l
l
5.25
V
7.2
0.8
0.5
0.5
8
1
40
110
mA
mA
μA
μA
18
1.25
1.25
20
100
275
mW
μW
μW
ADC TIMING CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
CONDITIONS
fSMPL
Maximum Sampling Frequency
l
tCONV
Conversion Time
l
380
tACQ
Acquisition Time
l
200
ns
tCYC
Time Between Conversions
l
625
ns
tCNVH
CNV High Time
l
20
ns
tBUSYLH
CNV ↑ to BUSY Delay
tCNVL
tQUIET
tACQ = tCYC –tCONV – tBUSYLH (Note 10)
MIN
TYP
MAX
UNITS
1.6
Msps
410
ns
CL = 20pF (Note 11)
l
Minimum Low Time for CNV
(Note 11)
l
20
ns
SCK Quiet Time from CNV ↑
(Note 10)
l
20
ns
tSCK
SCK Period
(Notes 11, 12)
l
10
ns
tSCKH
SCK High Time
l
4
15
ns
ns
237918p
4
LTC2379-18
ADC TIMING CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
tSCKL
SCK Low Time
CONDITIONS
tSSDISCK
SDI Setup Time From SCK ↑
tHSDISCK
tSCKCH
MIN
TYP
MAX
UNITS
l
4
ns
(Note 11)
l
4
ns
SDI Hold Time From SCK ↑
(Note 11)
l
1
ns
SCK Period in Chain Mode
tSCKCH = tSSDISCK + tDSDO (Note 11)
l
13.5
ns
tDSDO
SDO Data Valid Delay from SCK ↑
CL = 20pF (Note 11)
l
tHSDO
SDO Data Remains Valid Delay from SCK ↑
CL = 20pF (Note 10)
l
9.5
1
ns
ns
tDSDOBUSYL
SDO Data Valid Delay from BUSY ↓
CL = 20pF (Note 10)
l
5
ns
tEN
Bus Enable Time After RDL ↓
(Note 11)
l
16
ns
tDIS
Bus Relinquish Time After RDL ↑
(Note 11)
l
13
ns
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may effect device
reliability and lifetime.
Note 2: All voltage values are with respect to ground.
Note 3: When these pin voltages are taken below ground or above REF or
OVDD, they will be clamped by internal diodes. This product can handle
input currents up to 100mA below ground or above REF or OVDD without
latch-up.
Note 4: VDD = 2.5V, OVDD = 2.5V, REF = 5V, fSMPL = 1.6MHz.
Note 5: Recommended operating conditions.
Note 6: Integral nonlinearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
Note 7: Bipolar zero-scale error is the offset voltage measured from
–0.5LSB when the output code flickers between 00 0000 0000 0000 0000
and 11 1111 1111 1111 1111. Full-scale bipolar error is the worst-case of
–FS or +FS untrimmed deviation from ideal first and last code transitions
and includes the effect of offset error.
Note 8: All specifications in dB are referred to a full-scale ±5V input with a
5V reference voltage.
Note 9: fSMPL = 1.6MHz, IREF varies proportionately with sample rate.
Note 10: Guaranteed by design, not subject to test.
Note 11: Parameter tested and guaranteed at OVDD = 1.71V, OVDD = 2.5V
and OVDD = 5.25V.
Note 12: tSCK of 10ns maximum allows a shift clock frequency up to
100MHz for rising capture.
0.8*OVDD
tWIDTH
0.2*OVDD
tDELAY
tDELAY
0.8*OVDD
0.8*OVDD
0.2*OVDD
0.2*OVDD
50%
50%
237918 F01
Figure 1. Voltage Levels for Timing Specifications
237918p
5
LTC2379-18
TYPICAL PERFORMANCE CHARACTERISTICS
fSMPL = 1.6Msps, unless otherwise noted.
Integral Nonlinearity
vs Output Code
TA = 25°C, VDD = 2.5V, OVDD = 2.5V, REF = 5V,
Differential Nonlinearity
vs Output Code
DC Histogram
70000
1.0
2.0
1.5
60000
0.5
0.5
0.0
–0.5
–1.0
50000
COUNTS
DNL ERROR (LSB)
INL ERROR (LSB)
1.0
0.0
30000
20000
–0.5
10000
–1.5
–2.0
0
–1.0
65536
131072
196608
OUTPUT CODE
262144
0
65536
131072
196608
OUTPUT CODE
238018 G01
–80
105
–90
100
SNR, SINAD (dBFS)
–40
THD, Harmonics
vs Input Frequency
SNR, SINAD vs Input Frequency
SNR = 101.2dB
THD = –120dB
SINAD = 101.1dB
SFDR = 121dB
–20
237918 G03
237918 G02
32k Point FFT fS = 1.6Msps,
fIN = 2kHz
0
131068 131069 131070 131071 131072 131073
CODE
262144
–60
–80
–100
–120
–140
HARMONICS, THD (dBFS)
0
AMPLITUDE (dBFS)
40000
SNR
95
SINAD
90
85
–100
THD
–110
2ND
–120
–130
3RD
–160
–180
80
100 200 300 400 500 600 700 800
FREQUENCY (kHz)
0
25
50
SNR, SINAD vs Input level,
fIN = 2kHz
SNR, SINAD (dBFS)
SNR, SINAD (dBFS)
101.5
SNR
SINAD
100.5
102
–100
101
–105
100
SNR
99
SINAD
98
97
95
–20
–10
INPUT LEVEL (dB)
0
237918 G07
50
75 100 125 150 175 200
FREQUENCY (kHz)
THD, Harmonics vs Reference
Voltage, fIN = 2kHz
96
–30
25
237918 G06
SNR, SINAD vs Reference
Voltage, fIN = 2kHz
102.0
100.0
–40
0
237918 G05
237918 G04
101.0
–140
75 100 125 150 175 200
FREQUENCY (kHz)
HARMONICS, THD (dBFS)
0
–110
THD
–115
3RD
–120
2ND
–125
–130
–135
2.5
3.0
3.5
4.0
4.5
REFERENCE VOLTAGE (V)
5.0
237918 G16
–140
2.5
3.0
3.5
4.0
4.5
REFERENCE VOLTAGE (V)
5.0
237918 G17
237918p
6
LTC2379-18
TYPICAL PERFORMANCE CHARACTERISTICS
fSMPL = 1.6Msps, unless otherwise noted.
SNR, SINAD vs Temperature,
fIN = 2kHz
TA = 25°C, VDD = 2.5V, OVDD = 2.5V, REF = 5V,
THD, Harmonics vs Temperature,
fIN = 2kHz
103
INL/DNL vs Temperature
–110
2
SNR
102
100
99
98
–115
INL/DNL ERROR (LSB)
HARMONICS, THD (dBFS)
SNR, SINAD (dBFS)
SINAD
101
THD
–120
3RD
–125
2ND
–130
MAX INL
1
MAX DNL
0
MIN DNL
MIN INL
–1
97
96
–55 –35 –15
–135
–55 –35 –15
5 25 45 65 85 105 125
TEMPERATURE (°C)
237918 G08
Full-Scale Error vs Temperature
0
–2
–4
8
0.25
7
0
–0.25
–0.50
–0.75
–1.00
+FS
–6
Supply Current vs Temperature
0.50
POWER SUPPLY CURRENT (mA)
OFFSET ERROR (LSB)
FULL-SCALE ERROR (LSB)
2
237918 G10
Offset Error vs Temperature
–FS
4
5 25 45 65 85 105 125
TEMPERATURE (°C)
237918 G09
8
6
–2
–55 –35 –15
5 25 45 65 85 105 125
TEMPERATURE (°C)
IVDD
6
5
4
3
IOVDD
2
1
IREF
5 25 45 65 85 105 125
TEMPERATURE (°C)
–1.25
–55 –35 –15
5 25 45 65 85 105 125
TEMPERATURE (°C)
Shutdown Current vs Temperature
POWER SUPPLY CURRENT (mA)
POWER-DOWN CURRENT (μA)
40
30
25
20
15
10
1.0
7
0.9
6
IVDD
5
4
3
2
1
0
–55 –35 –15
0
237918 G14
Reference Current vs
Reference Voltage
8
5
5 25 45 65 85 105 125
TEMPERATURE (°C)
237918 G13
Supply Current vs Sampling Rate
IVDD + IOVDD + IREF
35
5 25 45 65 85 105 125
TEMPERATURE (°C)
237918 G12
237918 G11
45
0
–55 –35 –15
IOVDD
IREF
0
200 400 600 800 1000 1200 1400 1600
SAMPLING RATE (kHz)
237918 G15
REFERENCE CURRENT (mA)
–8
–55 –35 –15
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
2.5
3.0
3.5
4.0
4.5
REFERENCE VOLTAGE (V)
5.0
237918 G18
237918p
7
LTC2379-18
PIN FUNCTIONS
CHAIN (Pin 1): Chain Mode Selector Pin. When low, the
LTC2379-18 operates in Normal Mode and the RDL/SDI
input pin functions to enable or disable SDO. When high,
the LTC2379-18 operates in Chain Mode and the RDL/
SDI pin functions as SDI, the daisychain serial data input.
BUSY (Pin 11): BUSY indicator. Goes high at the start of
a new conversion and returns low when the conversion
has finished.
RDL/SDI (Pin 12): When CHAIN is low, the part is in Normal Mode and the pin is treated as a bus enabling input.
When CHAIN is high, the part is in chain mode and the
pin is treated as a serial data input pin where data from
another ADC in the daisychain is input.
VDD (Pin 2): 2.5V Power Supply. The range of VDD is
2.375V to 2.625V. Bypass VDD to GND with a 10μF ceramic
capacitor.
GND (Pins 3, 6, 10 and 16): Ground.
IN+, IN– (Pins 4, 5): Positive and Negative Differential
Analog Inputs.
SCK (Pin 13): Serial Data Clock Input. When SDO is enabled,
the conversion result or daisychain data from another ADC
is shifted out on the rising edges of this clock MSB first.
REF (Pin 7): Reference Input. The range of REF is 2.5V
to 5.1V. This pin is referred to the GND pin and should be
decoupled closely to the pin with a 47μF ceramic capacitor
(X5R, 0805 size).
SDO (Pin 14): Serial Data Output. The conversion result
or daisychain data is output on this pin on each rising
edge of SCK MSB first. The output data is in 2’s complement format.
OVDD (Pin 15): I/O Interface Digital Power. The range of
OVDD is 1.71V to 5.25V. This supply is nominally set to
the same supply as the host interface (1.8V, 2.5V, 3.3V,
or 5V). Bypass OVDD to GND with a 0.1μF capacitor.
REF/DGC (Pin 8): When tied to REF, digital gain compression
is disabled and the LTC2379-18 defines full-scale according
to the ±VREF analog input range. When tied to GND, digital
gain compression is enabled and the LTC2379-18 defines
full-scale with inputs that swing between 10% and 90%
of the ±VREF analog input range.
GND (Exposed Pad Pin 17 – DFN Package Only): Ground.
Exposed pad must be soldered directly to the ground plane.
CNV (Pin 9): Convert Input. A rising edge on this input
powers up the part and initiates a new conversion.
FUNCTIONAL BLOCK DIAGRAM
VDD = 2.5V
REF = 5V
OVDD = 1.8V to 5V
LTC2379-18
IN+
+
18-BIT SAMPLING ADC
IN–
SPI
PORT
–
CONTROL LOGIC
CHAIN
SDO
RDL/SDI
SCK
CNV
BUSY
REF/DGC
GND
237918 BD01
237918p
8
LTC2379-18
TIMING DIAGRAM
Conversion Timing Using the Serial Interface
CHAIN, RDL/SDI = 0
CNV
POWER-DOWN AND ACQUIRE
BUSY
CONVERT
SCK
D17 D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
SDO
237918 TD02
237918p
9
LTC2379-18
OVERVIEW
The LTC2379-18 is a low noise, low power, high speed
18-bit successive approximation register (SAR) ADC.
Operating from a single 2.5V supply, the LTC2379-18
supports a large and flexible ±VREF fully differential input
range with VREF ranging from 2.5V to 5.1V, making it ideal
for high performance applications which require a wide
dynamic range. The LTC2379-18 achieves ±2LSB INL max,
no missing codes at 18-bits and 101dB SNR.
Fast 1.6Msps throughput with no cycle latency makes
the LTC2379-18 ideally suited for a wide variety of high
speed applications. An internal oscillator sets the conversion time, easing external timing considerations. The
LTC2379-18 dissipates only 18mW at 1.6Msps, while an
auto power-down feature is provided to further reduce
power dissipation during inactive periods.
The LTC2379-18 offers a digital gain compression (DGC)
feature that allows a full-scale input to be achieved with
inputs that swing between 10% and 90% of the ±VREF
analog input range. This allows the input buffer amplifier to be operated from a single positive supply without
headroom issues, resulting in a lower power system.
OUTPUT CODE (TWO’S COMPLEMENT)
APPLICATIONS INFORMATION
011...111
BIPOLAR
ZERO
011...110
000...001
000...000
111...111
111...110
100...001
FSR = +FS – –FS
1LSB = FSR/262144
100...000
–FSR/2
–1 0V 1
FSR/2 – 1LSB
LSB
LSB
INPUT VOLTAGE (V)
237918 F02
Figure 2. LTC2379-18 Transfer Function
ANALOG INPUT
The analog inputs of the LTC2379-18 are fully differential
in order to maximize the signal swing that can be digitized.
The analog inputs can be modeled by the equivalent circuit
shown in Figure 3. The diodes at the input provide ESD
protection. In the acquisition phase, each input sees approximately 45pF (CIN) from the sampling CDAC in series
with 40Ω (RON) from the on-resistance of the sampling
switch. Any unwanted signal that is common to both
REF
CONVERTER OPERATION
The LTC2379-18 operates in two phases. During the acquisition phase, the charge redistribution capacitor D/A
converter (CDAC) is connected to the IN+ and IN– pins to
sample the differential analog input voltage. A rising edge
on the CNV pin initiates a conversion. During the conversion
phase, the 18-bit CDAC is sequenced through a successive approximation algorithm, effectively comparing the
sampled input with binary-weighted fractions of the reference voltage (e.g. VREF/2, VREF/4 … VREF/262144) using
the differential comparator. At the end of conversion, the
CDAC output approximates the sampled analog input. The
ADC control logic then prepares the 18-bit digital output
code for serial transfer.
RON
40Ω
IN+
REF
IN–
RON
40Ω
CIN
45pF
CIN
45pF
BIAS
VOLTAGE
237918 F03
Figure 3. The Equivalent Circuit for the
Differential Analog Input of the LTC2379-18
inputs will be reduced by the common mode rejection of
the ADC. The inputs draw a current spike while charging
the CIN capacitors during acquisition. During conversion,
the analog inputs draw only a small leakage current.
TRANSFER FUNCTION
The LTC2379-18 digitizes the full-scale voltage of 2 × REF
into 218 levels, resulting in an LSB size of 38μV with
REF = 5V. The ideal transfer function is shown in Figure 2.
The output data is in 2’s complement format.
INPUT DRIVE CIRCUITS
A low impedance source can directly drive the high impedance inputs of the LTC2379-18 without gain error. A
high impedance source should be buffered to minimize
237918p
10
LTC2379-18
APPLICATIONS INFORMATION
settling time during acquisition and to optimize the distortion performance of the ADC. Minimizing settling time
is important even for DC inputs, because the ADC inputs
draw a current spike when entering acquisition.
For best performance, a buffer amplifier should be used
to drive the analog inputs of the LTC2379-18. The amplifier provides low output impedance, which produces fast
settling of the analog signal during the acquisition phase.
It also provides isolation between the signal source and
the current spike the ADC inputs draw.
Input Filtering
The noise and distortion of the buffer amplifier and signal
source must be considered since they add to the ADC noise
and distortion. Noisy input signals should be filtered prior
to the buffer amplifier input with an appropriate filter to
minimize noise. The simple 1-pole RC lowpass filter (LPF1)
shown in Figure 4 is sufficient for many applications.
Another filter network consisting of LPF2 should be used
between the buffer and ADC input to both minimize the
noise contribution of the buffer and to help minimize disturbances reflected into the buffer from sampling transients.
Long RC time constants at the analog inputs will slow
down the settling of the analog inputs. Therefore, LPF2
requires a wider bandwidth than LPF1. A buffer amplifier
with a low noise density must be selected to minimize
degradation of the SNR.
Single-Ended-to-Differential Conversion
For single-ended input signals, a single-ended to differential
conversion circuit must be used to produce a differential
signal at the inputs of the LTC2379-18. The LT6350 ADC
driver is recommended for performing single-ended-todifferential conversions. The LT6350 is flexible and may
be configured to convert single-ended signals of various
amplitudes to the ±5V differential input range of the
LTC2379-18. The LT6350 is also available in H-grade to
complement the extended temperature operation of the
LTC2379-18 up to 125°C.
Figure 5a shows the LT6350 being used to convert a 0V
to 5V single-ended input signal. In this case, the first
amplifier is configured as a unity gain buffer and the singleended input signal directly drives the high-impedance
input of the amplifier. As shown in the FFT of Figure 5b,
the LT6350 drives the LTC2379-18 to near full datasheet
performance.
LT6350
5V
4
5V
+
–
8
0V
1
RINT
OUT1
RINT
2
+
–
0V
5V
–
+
5
OUT2
0V
VCM = VREF/2
237918 F05a
LPF2
SINGLE-ENDEDINPUT SIGNAL LPF1
500Ω
3300pF
20Ω
IN+
3300pF
6600pF
20Ω
SINGLE-ENDED- 3300pF
BW = 48kHz TO-DIFFERENTIAL
DRIVER
BW = 800kHz
Figure 4. Input Signal Chain
LTC2379-18
Figure 5a. LT6350 Converting a 0V-5V Single-Ended
Signal to a ±5V Differential Input Signal
0
SNR = 101dB
THD = –111.5dB
SINAD = 100.8dB
SFDR = 114.5dB
–20
–40
AMPLITUDE (dBFS)
High quality capacitors and resistors should be used in the
RC filters since these components can add distortion. NPO
and silver mica type dielectric capacitors have excellent
linearity. Carbon surface mount resistors can generate
distortion from self heating and from damage that may
occur during soldering. Metal film surface mount resistors
are much less susceptible to both problems.
–60
–80
–100
–120
–140
–160
IN–
–180
237918 F04
0
100 200 300 400 500 600 700 800
FREQUENCY (kHz)
237918 F05b
Figure 5b. 32k Point FFT Plot with fIN = 10kHz
for Circuit Shown in Figure 5a
237918p
11
LTC2379-18
APPLICATIONS INFORMATION
R1, R2, R3 and R4 must be selected in relation to RIN to
achieve the desired attenuation and to maintain a balanced
input impedance in the first amplifier. Table 1 shows the
resulting SNR and THD for several values of RIN, R1, R2,
R3 and R4 in this configuration. Figure 6b shows the resulting FFT when using the LT6350 as shown in Figure 6a.
VCM
R2 = 499k
200pF
R2
(Ω)
R3
(Ω)
R4
(Ω)
SNR
(dB)
THD
(dB)
2k
499
499
2k
402
100.8
99
10k
2.49k
2.49k
10k
2k
109.5
TBD
100k
24.9k
24.9k
100k
20k
94.8
96
5V
+
–
RINT
1
10V
0V
–10V
RIN = 2k
RINT
2
R1 = 499k
OUT1
+
–
0V
5V
–
+
5
OUT2
0V
VCM = VREF/2
220pF
237918 F06a
Figure 6a. LT6350 Converting a ±10V Single-Ended Signal to
a ±5V Differential Input Signal
0
SNR = 100.8dB
THD = –99.3dB
SINAD = 97.8dB
SFDR = 101.2dB
–20
–40
–60
–80
–100
–120
–140
–160
–180
0
R1
(Ω)
8
10μF R4 = 402k
R3 = 2k
Table 1. SNR, THD vs RIN for ±10V Single-Ended Input Signal.
RIN
(Ω)
LT6350
4
AMPLITUDE (dBFS)
The LT6350 can also be used to buffer and convert large
true bipolar signals which swing below ground to the
±5V differential input range of the LTC2379-18 in order
to maximize the signal swing that can be digitized. Figure 6a shows the LT6350 being used to convert a ±10V
true bipolar signal for use by the LTC2379-18. In this
case, the first amplifier in the LT6350 is configured as
an inverting amplifier stage, which acts to attenuate and
level shift the input signal to the 0V to 5V input range of
the LTC2379-18. In the inverting amplifier configuration,
the single-ended input signal source no longer directly
drives a high impedance input of the first amplifier. The
input impedance is instead set by resistor RIN. RIN must
be chosen carefully based on the source impedance of the
signal source. Higher values of RIN tend to degrade both
the noise and distortion of the LT6350 and LTC2379-18
as a system.
100 200 300 400 500 600 700 800
FREQUENCY (kHz)
237918 F06b
Figure 6b. 32k Point FFT Plot with fIN = 2kHz
for Circuit Shown in Figure 6a
5V
LT6203
3
0V
2
5V
+
–
1
+
–
7
0V
Fully Differential Inputs
5V
To achieve the full distortion performance of the
LTC2379-18, a low distortion fully differential signal source
driven through the LT6203 configured as two unity gain
buffers as shown in Figure 7 can be used to get the full
data sheet THD specification of –118dB.
Digital Gain Compression
The LTC2379-18 offers a digital gain compression (DGC)
feature which defines the full-scale input swing to be between 10% and 90% of the ±VREF analog input range. To
5
0V
6
5V
0V
237918 F07
Figure 7. LT6203 Buffering a Fully Differential Signal Source
enable digital gain compression, bring the REF/DGC pin
low. This feature allows the LT6350 to be powered off of
a single +5.5V supply since each input swings between
0.5V and 4.5V as shown in Figure 8. Needing only one
positive supply to power the LT6350 results in additional
power savings for the entire system.
237918p
12
LTC2379-18
APPLICATIONS INFORMATION
high accuracy, the LTC6655-5 is particularly well suited for
use with the LTC2379-18. The LTC6655-5 offers 0.025%
(max) initial accuracy and 2ppm/°C (max) temperature
coefficient for high precision applications. The LTC6655-5
is fully specified over the H-grade temperature range and
complements the extended temperature operation of the
LTC2379-18 up to 125°C. We recommend bypassing the
LTC6655-5 with a 47μF ceramic capacitor (X5R, 0805 size)
close to the REF pin.
5V
4.5V
0.5V
0V
237918 F08
Figure 8. Input Swing of the LTC2379 with Gain
Compression Enabled
Figure 9a shows how to configure the LT6350 to accept a
±10V true bipolar input signal and attenuate and level shift
the signal to the reduced input range of the LTC2379-18
when digital gain compression is enabled. Figure 9b shows
an FFT plot with the LTC2379-18 being driven by the LT6350
with digital gain compression enabled.
The REF pin of the LTC2379-18 draws charge (QCONV) from
the 47μF bypass capacitor during each conversion cycle.
The reference replenishes this charge with a DC current,
IREF = QCONV/tCYC. The DC current draw of the REF pin,
IREF, depends on the sampling rate and output code. If
the LTC2379-18 is used to continuously sample a signal
at a constant rate, the LTC6655-5 will keep the deviation
of the reference voltage over the entire code span to less
than 0.5LSBs.
ADC REFERENCE
The LTC2379-18 requires an external reference to define
its input range. A low noise, low temperature drift reference is critical to achieving the full datasheet performance
of the ADC. Linear Technology offers a portfolio of high
performance references designed to meet the needs of
many applications. With its small size, low power and
When idling, the REF pin on the LTC2379-18 draws only
a small leakage current (< 1μA). In applications where a
burst of samples is taken after idling for long periods as
shown in Figure 10, IREF quickly goes from approximately
0μA to a maximum of 1.2mA at 1.6Msps. This step in DC
VIN
5.5V
0
LTC6655-5
5V
1k
4.5V
1k
LT6350
V+
6.04k
4
8
4.32k
10μF
+
–
1
10V
0V
–10V
RIN = 15k
2.5V
3
OUT1
0.5V
IN+
20Ω
RINT
RINT
3300pF
2
3.01k
VCM
IN
20Ω
5
V–
OUT2
4.5V
6
VDD
LTC2379-18
3300pF
–
+
REF
AMPLITUDE (dBFS)
–40
47μF
VCM
10μF
SNR = 99dB
THD = –95dB
SINAD = 94.6dB
SFDR = 96.3dB
–20
VOUT_S
–60
–80
–100
–120
–140
–
REF/DGC
–160
237918 F09a
3300pF
–180
0
0.5V
100 200 300 400 500 600 700 800
FREQUENCY (kHz)
237918 F09b
Figure 9a. LT6350 Configured to Accept a ±10V Input Signal While Running Off of a
Single 5.5V Supply When Digital Gain Compression Is Enabled in the LTC2379-18
Figure 9b. 32k Point FFT Plot
with fIN = 2kHz for Circuit Shown
in Figure 9a
CNV
IDLE
PERIOD
IDLE
PERIOD
237918 F10
Figure 10. CNV Waveform Showing Burst Sampling
237918p
13
LTC2379-18
APPLICATIONS INFORMATION
current draw triggers a transient response in the reference
that must be considered since any deviation in the reference output voltage will affect the accuracy of the output
code. In applications where the transient response of the
reference is important, the fast settling LTC6655-5 reference is also recommended.
DYNAMIC PERFORMANCE
Fast Fourier Transform (FFT) techniques are used to test
the ADC’s frequency response, distortion and noise at the
rated throughput. By applying a low distortion sine wave
and analyzing the digital output using an FFT algorithm,
the ADC’s spectral content can be examined for frequencies outside the fundamental. The LTC2379-18 provides
guaranteed tested limits for both AC distortion and noise
measurements.
Signal-to-Noise Ratio (SNR)
The signal-to-noise ratio (SNR) is the ratio between the
RMS amplitude of the fundamental input frequency and
the RMS amplitude of all other frequency components
except the first five harmonics and DC. Figure 11 shows
that the LTC2379-18 achieves a typical SNR of 101dB at
a 1.6MHz sampling rate with a 2kHz input.
Total Harmonic Distortion (THD)
Total Harmonic Distortion (THD) is the ratio of the RMS sum
of all harmonics of the input signal to the fundamental itself.
The out-of-band harmonics alias into the frequency band
between DC and half the sampling frequency (fSMPL/2).
THD is expressed as:
THD= 20log
V22 + V32 + V42 +…+ VN2
Signal-to-Noise and Distortion Ratio (SINAD)
The signal-to-noise and distortion ratio (SINAD) is the
ratio between the RMS amplitude of the fundamental input
frequency and the RMS amplitude of all other frequency
components at the A/D output. The output is band-limited
to frequencies from above DC and below half the sampling
frequency. Figure 11 shows that the LTC2379-18 achieves
a typical SINAD of 100.5dB at a 1.6MHz sampling rate
with a 2kHz input.
0
SNR = 101.2dB
THD = –120dB
SINAD = 101.1dB
SFDR = 121dB
–20
AMPLITUDE (dBFS)
–40
–60
V1
where V1 is the RMS amplitude of the fundamental frequency and V2 through VN are the amplitudes of the second
through Nth harmonics.
POWER CONSIDERATIONS
The LTC2379-18 provides two power supply pins: the
2.5V power supply (VDD), and the digital input/output
interface power supply (OVDD). The flexible OVDD supply
allows the LTC2379-18 to communicate with any digital
logic operating between 1.8V and 5V, including 2.5V and
3.3V systems.
Power Supply Sequencing
–80
–100
–120
–140
–160
–180
0
100 200 300 400 500 600 700 800
FREQUENCY (kHz)
237918 F11
Figure 11. 32k Point FFT of the LTC2379-18
The LTC2379-18 does not have any specific power supply
sequencing requirements. Care should be taken to adhere
to the maximum voltage relationships described in the
Absolute Maximum Ratings section. The LTC2379-18
has a power-on-reset (POR) circuit that will reset the
LTC2379-18 at initial power-up or whenever the power
supply voltage drops below 1V. Once the supply voltage
reenters the nominal supply voltage range, the POR will
237918p
14
LTC2379-18
APPLICATIONS INFORMATION
reinitialize the ADC. No conversions should be initiated
until 20μs after a POR event to ensure the reinitialization
period has ended. Any conversions initiated before this
time will produce invalid results.
powered-down for a larger fraction of the conversion cycle
(tCYC) at lower sample rates, thereby reducing the average
power dissipation which scales with the sampling rate as
shown in Figure 12.
TIMING AND CONTROL
DIGITAL INTERFACE
CNV Timing
The LTC2379-18 has a serial digital interface. The flexible
OVDD supply allows the LTC2379-18 to communicate with
any digital logic operating between 1.8V and 5V, including
2.5V and 3.3V systems.
Internal Conversion Clock
The LTC2379-18 has an internal clock that is trimmed to
achieve a maximum conversion time of 410ns. With a minimum acquisition time of 200ns, throughput performance
of 1.6Msps is guaranteed without any external adjustments.
Auto Power-Down
The LTC2379-18 automatically powers down after a conversion has been completed and powers up once a new
conversion is initiated on the rising edge of CNV. During
power down, data from the last conversion can be clocked
out. To minimize power dissipation during power down,
disable SDO and turn off SCK. The auto power-down feature
will reduce the power dissipation of the LTC2379-18 as
the sampling frequency is reduced. Since power is consumed only during a conversion, the LTC2379-18 remains
The serial output data is clocked out on the SDO pin when
an external clock is applied to the SCK pin if SDO is enabled.
Clocking out the data after the conversion will yield the
best performance. With a shift clock frequency of at least
100MHz, a 1.6Msps throughput is still achieved. The serial
output data changes state on the rising edge of SCK and
can be captured on the falling edge or next rising edge of
SCK. D17 remains valid till the first rising edge of SCK.
The serial interface on the LTC2379-18 is simple and
straightforward to use. The following sections describe the
operation of the LTC2379-18. Several modes are provided
depending on whether a single or multiple ADCs share the
SPI bus or are daisy-chained.
8
POWER SUPPLY CURRENT (mA)
The LTC2379-18 conversion is controlled by CNV. A rising edge on CNV will start a conversion and power up the
LTC2379-18. Once a conversion has been initiated, it cannot
be restarted until the conversion is complete. For optimum
performance, CNV should be driven by a clean low jitter
signal. Converter status is indicated by the BUSY output
which remains high while the conversion is in progress.
To ensure that no errors occur in the digitized results, any
additional transitions on CNV should occur within 40ns
from the start of the conversion or after the conversion
has been completed. Once the conversion has completed,
the LTC2379-18 powers down and begins acquiring the
input signal.
7
6
IVDD
5
4
3
2
IOVDD
1
IREF
0
0
200 400 600 800 1000 1200 1400 1600
SAMPLING RATE (kHz)
237918 F12
Figure 12. Power Supply Current of the LTC2379-18
Versus Sampling Rate
237918p
15
LTC2379-18
TIMING DIAGRAM
Normal Mode, Single Device
Figure 13 shows a single LTC2379-18 operated in Normal
Mode with CHAIN and RDL/SDI tied to ground. With RDL/
SDI grounded, SDO is enabled and the MSB(D17) of the
new conversion data is available at the falling edge of
BUSY. This is the simplest way to operate the LTC2379-18.
When CHAIN = 0, the LTC2379-18 operates in Normal
mode. In Normal mode, RDL/SDI enables or disables the
serial data output pin SDO. If RDL/SDI is high, SDO is in
high-impedance. If RDL/SDI is low, SDO is driven.
CONVERT
DIGITAL HOST
CNV
BUSY
CHAIN
IRQ
LTC2379-18
RDL/SDI
SDO
DATA IN
SCK
CLK
238018 F13a
POWER-DOWN
AND ACQUIRE
CONVERT
POWER-DOWN AND ACQUIRE
CHAIN = 0
RDL/SDI = 0
CONVERT
tCYC
tCNVH
tCNVL
CNV
tACQ = tCYC – tCONV – tBUSYLH
tCONV
BUSY
tACQ
tSCK
tBUSYLH
tSCKH
1
SCK
2
3
tHSDO
tDSDOBUSYL
SDO
tQUIET
16
17
18
tSCKL
tDSDO
D17
D16
D15
D1
D0
237918 F13
Figure 13. Using a Single LTC2379-18 in Normal Mode
237918p
16
LTC2379-18
TIMING DIAGRAM
Normal Mode, Multiple Devices
Since SDO is shared, the RDL/SDI input of each ADC must
be used to allow only one LTC2379-18 to drive SDO at a
time in order to avoid bus conflicts. As shown in Figure 14,
the RDL/SDI inputs idle high and are individually brought
low to read data out of each device between conversions.
When RDL/SDI is brought low, the MSB of the selected
device is output onto SDO.
Figure 14 shows multiple LTC2379-18 devices operating
in Normal Mode(CHAIN = 0) sharing CNV, SCK and SDO.
By sharing CNV, SCK and SDO, the number of required
signals to operate multiple ADCs in parallel is reduced.
RDLB
RDLA
CONVERT
CNV
CNV
CHAIN
CHAIN
LTC2379-18
SDO
B
BUSY
IRQ
LTC2379-18
DIGITAL HOST
SDO
A
RDL/SDI
RDL/SDI
SCK
SCK
DATA IN
CLK
237918 F15
POWER-DOWN
AND ACQUIRE
CONVERT
CONVERT
POWER-DOWN AND ACQUIRE
CHAIN = 0
tCNVL
CNV
tCONV
BUSY
tBUSYLH
RDL/SDIA
RDL/SDIB
tSCK
SCK
1
2
tSCKH
3
16
17
18
tHSDO
SDO
D17A
D16A
D15A
19
20
21
34
35
36
tSCKL
tDSDO
tEN
Hi-Z
tQUIET
tDIS
D1A
D0A
Hi-Z
D17B
D16B
D15B
D1B
D0B
Hi-Z
237918 F14
Figure 14. Normal Mode With Multiple Devices Sharing CNV, SCK and SDO
237918p
17
LTC2379-18
TIMING DIAGRAM
When CHAIN = OVDD, the LTC2379-18 operates in Chain
Mode. In Chain Mode, SDO is always enabled and RDL/SDI
serves as the serial data input pin (SDI) where daisychain
data output from another ADC can be input.
This is useful for applications where hardware constraints
may limit the number of lines needed to interface to a large
number of converters. Figure 15 shows an example with
two daisy chained devices. The MSB of converter A will
appear at SDO of converter B after 18 SCK cycles. The
MSB of converter A is clocked in at the SDI/RDL pin of
converter B on the rising edge of the first SCK.
CONVERT
OVDD
OVDD
CNV
CHAIN
LTC2379-18
RDL/SDI
DIGITAL HOST
LTC2379-18
RDL/SDI
SDO
A
CNV
CHAIN
IRQ
BUSY
B
DATA IN
SDO
SCK
SCK
CLK
237918 F15a
POWER-DOWN
AND ACQUIRE
CONVERT
CONVERT
POWER-DOWN AND ACQUIRE
CHAIN = OVDD
RDL/SDIA = 0
tCYC
tCNVL
CNV
BUSY
tCONV
tBUSYLH
tSCKCH
SCK
1
2
3
16
17
tSSDISCK
18
19
20
34
35
36
tSCKL
tHSDO
tHSDISCK
SDOA = RDL/SDIB
tQUIET
tSCKH
tDSDO
D17A
D16A
D15A
D1A
D0A
D17B
D16B
D15B
D1B
D0B
tDSDOBUSYL
SDOB
D17A
D16A
D1A
D0A
237918 F15
Figure 15. Chain Mode Timing Diagram
237918p
18
LTC2379-18
BOARD LAYOUT
To obtain the best performance from the LTC2379-18
a printed circuit board is recommended. Layout for the
printed circuit board (PCB) should ensure the digital and
analog signal lines are separated as much as possible. In
particular, care should be taken not to run any digital clocks
or signals alongside analog signals or underneath the ADC.
Recommended Layout
The following is an example of a recommended PCB layout.
A single solid ground plane is used. Bypass capacitors to
the supplies are placed as close as possible to the supply
pins. Low impedance common returns for these bypass
capacitors are essential to the low noise operation of the
ADC. The analog input traces are screened by ground.
For more details and information refer to DC1783A, the
evaluation kit for the LTC2379-18.
Partial Top Silkscreen
237918p
19
LTC2379-18
BOARD LAYOUT
Partial Layer 1 Component Side
Partial Layer 2 Ground Plane
237918p
20
LTC2379-18
BOARD LAYOUT
Partial Layer 3 PWR Plane
Partial Layer 4 Bottom Layer
237918p
21
AIN –
J8
E7
EXT
VREF/2
R14
0Ω
R39
0Ω
JP5
HD1X3-100
EXT_CM
AIN+
J4
COUPLING
AC
DC
3
2
1
C8
1μF
+2.5V
COUPLING
AC
DC
C46
1μF
C47
OPT C48
10μF
6.3V
5
4
+3.3V
C1
0.1μF
2
5
4
+3.3V
C2
0.1μF
R3
CLK
33Ω
TO CPLD
R41
OPT
R40
1k
R18
1k
R9
OPT
C49
OPT
3
V+
C43
0.1μF
C55
1μF
6
C45 V –
10μF
2 +IN2
8 +IN1
V–
C63
10μF
6.3V
C62
1μF
R37
OPT
R34
0Ω
C61
10μF
6.3V
C42
15pF
R32
0Ω
V+
C44
1μF
C57
0.1μF
C59
1μF
V+
OUT2 5
–IN1
OUT1 4
U15
7 LT6350CMS8
SHDN
U2
R6 3 U8
3
NC7SZ04P5X NC7SVU04P5X
1k
R15
OPT
HD1X3-100
JP2
CM
C18
OPT
C17
10μF
JP1
HD1X3-100
R5
49.9Ω
1206
2
2
J1
CLKIN
1
3
C5
0.1μF
2
R2
1k
+3.3V
1
3
C60
0.1μF
C58
OPT
R35
OPT
R36
20Ω
R45
ØΩ
R32
20Ω
R31
OPT
C11
0.1μF
9V TO 10V
R38
OPT
SDO
5
1
3
5
7
9
11
13
9V TO
10V
C40
3300pF
NPO
R19
0Ω
C7
0.1μF
IN–
LTC2379-18
IN+
C10
0.1μF
C6
10μF
6.3V
C39
3300pF R16
0Ω 4
NPO
C9
10μF
6.3V
C19
3300pF
1206 NPO
+2.5V
+3.3V
U20
LTC6655AHMS8-5
1
8
SHDN
GND
2
7
VIN
OUT_F
3
6
GND OUT_S
4
5
GND
GND
J3
DC590
2
4
6
8
10
12
14
CNV
SCK
SDO
BUSY
R7
1k
3
2
1
JP6
FS
C56
0.1μF
3
3
R17 R13
2k
1k
U9
NC7SZ04P5X
2
4
VSS
6
5
7
3
2
1
C15
0.1μF
U7
C14
0.1μF 8 24LC025-I/ST
VCC
SCL
SCK
SDA
WP
CNV
ARRAY
A2
EEPROM
A1
A0
4
5
+3.3V
R10
4.99k
R11
4.99k
CLKOUT
C16 1
0.1μF
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
DB8
DB9
DB10
DB11
DB12
DB13
DB14
DB15
DB16
DB17
3
5
2 CNVST_33
FROM CPLD
U4
NC7SVU04P5X
+3.3V
C4
0.1μF
R12
4.99k
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
237918 BL
40
38
36
34
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
J2
CON-EDGE 40-100
R4
7 33Ω 4
8
+3.3V
C3
0.1μF
R8
33Ω
DC590 DETECT
TO CPLD
5
PR\
Q
CLR\
Q\
2
D
VCC
1
CP
GND
+3.3V
C13
0.8VREF
0.1μF
VREF
6
U3
NL17SZ74
+3.3V
4
HD1X3-100
U6
OPT NC7SZ66P5X 5
CNV
VCC
9
2 B
A 1
13 SCK
OE 4
14 SDO
GND
11 BUSY
3
12 RD
C20
47μF
6.3V
0805
RDL/SDI
VDD 2
OVDD 15
REF 7
8
REF/DGC
GND
GND
GND
GND
+
–
–
+
22
3
6
10
16
1
R1
33Ω
LTC2379-18
BOARD LAYOUT
Partial Schematic of Demoboard
237918p
LTC2379-18
PACKAGE DESCRIPTION
DE Package
16-Lead Plastic DFN (4mm × 3mm)
(Reference LTC DWG # 05-08-1732 Rev Ø)
R = 0.115
TYP
4.00 ±0.10
(2 SIDES)
0.70 ±0.05
2.20 ±0.05
3.30 ±0.10
3.00 ±0.10
(2 SIDES)
PACKAGE
OUTLINE
PIN 1
TOP MARK
(SEE NOTE 6)
1.70 ± 0.05
16
R = 0.05
TYP
3.30 ±0.05
3.60 ±0.05
0.40 ± 0.10
9
1.70 ± 0.10
PIN 1 NOTCH
R = 0.20 OR
0.35 s 45°
CHAMFER
(DE16) DFN 0806 REV Ø
8
0.75 ±0.05
0.200 REF
0.25 ± 0.05
0.45 BSC
3.15 REF
0.00 – 0.05 BOTTOM VIEW—EXPOSED PAD
3.15 REF
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED
1
0.23 ± 0.05
0.45 BSC
NOTE:
1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WGED-3) IN JEDEC
PACKAGE OUTLINE MO-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE
TOP AND BOTTOM OF PACKAGE
MS Package
16-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1669 Rev Ø)
4.039 p 0.102
(.159 p .004)
(NOTE 3)
0.889 p 0.127
(.035 p .005)
5.23
(.206)
MIN
16151413121110 9
3.20 – 3.45
(.126 – .136)
0.254
(.010)
DETAIL “A”
0o – 6o TYP
0.280 p 0.076
(.011 p .003)
REF
3.00 p 0.102
(.118 p .004)
(NOTE 4)
4.90 p 0.152
(.193 p .006)
GAUGE PLANE
0.305 p 0.038
(.0120 p .0015)
TYP
0.53 p 0.152
(.021 p .006)
0.50
(.0197)
BSC
RECOMMENDED SOLDER PAD LAYOUT
DETAIL “A”
0.18
(.007)
SEATING
NOTE:
PLANE
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
1234567 8
1.10
(.043)
MAX
0.17 – 0.27
(.007 – .011)
TYP
0.50
(.0197)
BSC
0.86
(.034)
REF
0.1016 p 0.0508
(.004 p .002)
MSOP (MS16) 1107 REV Ø
237918p
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
23
LTC2379-18
TYPICAL APPLICATION
LT6350 Configured to Accept a ±10V Input Signal While Running Off of a Single 5.5V Supply When
Digital Gain Compression Is Enabled in the LTC2379-18
VIN
5.5V
LTC6655-5
VOUT_S
5V
1k
47μF
VCM
4.5V
1k
10μF
LT6350
V+
6.04k
4
8
4.32k
10μF
+
–
1
10V
0V
–10V
RIN = 15k
2.5V
3
OUT1
0.5V
IN+
20Ω
RINT
RINT
3300pF
–
+
IN–
20Ω
5
V–
3.01k
OUT2
4.5V
6
VCM
VDD
LTC2379-18
3300pF
2
REF
3300pF
REF/DGC
237918 TA03
0.5V
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
ADCs
LTC2383-16/LTC2382-16/ 16-Bit, 1Msps/500ksps/250ksps Serial, Low power ADC 2.5V Supply, Differential Input, 92dB SNR, ±2.5V Input Range, Pin
LTC2381-16
Compatible Family in MSOP-16 and 4mm × 3mm DFN-16 package
LTC2393-16/LTC2392-16/ 16-Bit, 1Msps/500ksps/250ksps Parallel/Serial ADC
LTC2391-16
5V Supply, Differential Input, 94dB SNR, ±4.096V Input Range, Pin
Compatible Family in 7mm × 7mm LQFP-48 and QFN package
LTC1864/LTC1864L
16-Bit, 250ksps/150ksps 1-Channel μPower, ADC
5V/3V Supply, 1-Channel, 4.3mW/1.3mW, MSOP-8 Package
LTC1865/LTC1865L
16-Bit, 250ksps 2-Channel μPower ADC
5V/3V Supply, 1-Channel, 4.3mW/1.3mW, MSOP-8 Package
LTC2306
12-Bit, 500ksps, 1-Channel/2-Channel, Low Noise, ADC
LTC2355-14/LTC2356-14
14-Bit, 3.5Msps Serial ADC
3.3V Supply, 1-Channel, Unipolar/Bipolar, 18mW, MSOP-10 Package
LTC2641
16-Bit Single Serial VOUT DACs
±1LSB INL, ±1LSB DNL, MSOP-8 Package, 0V to 5V Output
LTC2630
12-Bit/10-Bit/8-Bit Single VOUT DACs
SC70 6-Pin Package, Internal Reference, ±1LSB INL (12Bits)
LTC6655
Precision Low Drift Low Noise Buffered Reference
2.5V, 5ppm/°C, 0.25ppm Peak-to-Peak Noise, MSOP-8 Package
LTC6652
Precision Low Drift Low Noise Buffered Reference
2.5V, 5ppm/°C, 2.1ppm Peak-to-Peak Noise, MSOP-8 Package
DACS
REFERENCES
AMPLIFIERS
LT6350
Low Noise Single-Ended-to-Differential ADC Driver
Rail-to-Rail Input and Outputs, 240ns 0.01% Settling Time
LT6200/LT6200-5/
LT6200-10
165MHz/800MHz/1.6GHz Op Amp with
Unity Gain/AV = 5/AV = 10
Low Noise Voltage: 0.95nV/√Hz (100kHz), Low Distortion: –80dB at
1MHz, TSOT23-6 Package
LT6202/LT6203
Single/Dual 100MHz Rail-to-Rail Input/Output Noise Low 1.9nV√Hz, 3mA Maximum, 100MHz Gain Bandwidth
Power Amplifiers
LTC1992
Low Power, Fully Differential Input/Output Amplifier/
Driver Family
1mA Supply Current
237918p
24 Linear Technology Corporation
LT 0111 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2011