MICREL MIC47050

MIC47050
500mA ULDO™ with Low Input
and Low Output Voltage
General Description
Features
The MIC47050 is a high-speed, ultra-low dropout, dualsupply NMOS ULDO™ designed to take advantage of
point-of-load applications that use multiple supply rails to
generate a low-voltage, high-current power supply. The
MIC47050 can source 500mA of output current while only
requiring a 1µF ceramic output capacitor for stability. A
1.5% output voltage accuracy, low dropout voltage (44mV
@ 500mA), and low ground current makes this device
ideally suited for mobile and point-of-load applications.
The MIC47050 has an NMOS output stage offering very
low output impedance. The NMOS output stage makes for
a unique ability to respond very quickly to sudden load
changes such as that required by a microprocessor, DSP
or FPGA. The MIC47050 consumes little quiescent current
and therefore can be used for driving the core voltages of
mobile processors, post regulating a core DC/DC
converter in any processor.
The MIC47050 is available in fixed and adjustable output
®
voltages in the tiny 2mm x 2mm MLF package with an
operating junction temperature range of −40°C to +125°C.
Data sheets and support documentation can be found on
Micrel’s web site at: www.micrel.com.
• Voltage Range
– Input Voltage: 1.0V to 3.6V
– Bias Voltage: 2.3V to 5.5V
• 0.4V to 2.0V output voltage range
• Low dropout voltage of 44mV at 500mA
• ±1.5% initial output voltage accuracy
• High bandwidth – very fast transient response
• Stable with a 1µF ceramic output capacitor
• Logic level enable input
• UVLO on both supply voltages
• Thermally-enhanced 2mm x 2mm MLF® package
• Junction temperature range of –40°C to +125°C
Applications
•
•
•
•
•
Point-of-load applications
PDAs, Notebooks, and Desktops
Datacom and Telecom systems
DSP, PLD and FPGA power supply
Low-voltage post regulation
_________________________________________________________________________________________________________________________
Typical Application
ULDO is a trademark of Micrel Inc.
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
March 2010
M9999-032310-A
Micrel, Inc.
MIC47050
Ordering Information
Voltage (1)
Marking Code(2)
Temperature
Range
Package
Lead Finish(3)
MIC47050-1.2YML
1.2V
ZG 4
−40°C to +125°C
6-Pin 2mm x 2mm MLF®
Pb-Free
MIC47050YML
ADJ
ZGA
−40°C to +125°C
6-Pin 2mm x 2mm MLF®
Pb-Free
Part Number
Notes:
1.
Other Voltage available. Contact Micrel Marketing for details.
2.
Overbar ( ¯ ) may not be to scale.
3.
MLF is a GREEN RoHS compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free.
®
Pin Configuration
6-pin 2mm x 2mm MLF® - Fixed (ML)
6-pin 2mm x 2mm MLF® - Adjustable (ML)
Pin Description
Fixed
ADJ
Pin Name
Pin Function
1
1
BIAS
Bias Supply. The bias supply is the power supply for the internal circuitry of the
regulator.
2
2
GND
Ground. Ground pins and exposed pad must be connected externally.
3
3
IN
4
4
OUT
Input Supply. Drain of NMOS pass transistor which is the power input voltage for
regulator. The NMOS pass transistor steps down this input voltage to create the
output voltage.
Output. Output Voltage of Regulator.
Power Good Output. Open-drain output. Output is driven low when the output voltage
is less than the power good threshold of its programmed nominal output voltage.
When the output goes above the power good threshold, the open-drain output goes
high-impedance, allowing it to be pulled up to a fixed voltage.
5
–
PGOOD
–
5
ADJ
Adjust Input. Connect external resistor divider to program the output voltage.
6
6
EN
Enable: TTL/CMOS compatible input. Logic high = enable, logic low = shutdown. Do
not leave floating.
EP
EP
GND
Exposed thermal pad. Connect to the ground plane to maximize thermal performance.
March 2010
2
M9999-032310-A
Micrel, Inc.
MIC47050
Absolute Maximum Ratings(1)
Operating Ratings(2)
IN Supply Voltage (VIN) ................................... –0.3V to +4V
Bias Supply Voltage (VBIAS)............................. –0.3V to +6V
Enable Voltage (VEN)....................................... –0.3V to +6V
Power Good Voltage (VPGOOD) ....................... .–0.3V to +6V
ADJ Pin Voltage (VADJ)................................... .–0.3V to +6V
OUT Pin Voltage (VOUT) ................................... .–0.3V to VIN
Lead Temperature (soldering,10 sec.)....................... 260°C
Storage Temperature (TS).........................–65°C to +150°C
ESD Rating(3) ......................................................... 2kV HBM
IN Supply Voltage (VIN) ............ +1.0V to +3.6V (VIN < VBIAS)
Bias Voltage (VBIAS)...................................... +2.3V to +5.5V
Enable Voltage (VEN)........................................... 0V to VBIAS
Power Good Voltage (VPGOOD) ........................... .0V to VBIAS
Output Voltage Range …………….. ................ 0.4V to 2.0V
Junction Temperature (TJ) ........................ –40°C to +125°C
Ambient Temperature (TA) .......................... –40°C to +85°C
Junction Thermal Resistance
2mm x 2mm MLF®-6L (θJA)................................90°C/W
2mm x 2mm MLF®-6L (θJC)................................45°C/W
Electrical Characteristics(4)
VIN = VOUT + 0.5V; VBIAS = VOUT+2.1V; COUT = 1µF; IOUT = 100µA; TJ = 25°C, bold values indicate –40°C≤ TJ ≤ +125°C, unless noted.
Parameter
Condition
Min.
Typ.
Max.
Units
3.6
V
1.0
V
Input Supply
1.0
Input Voltage Range (VIN)
(5)
VIN UVLO Threshold
0.7
VIN Rising
VIN UVLO Hysteresis
0.85
40
Ground Current in Shutdown (IGND)
VEN ≤ 0.2V (Regulator Shutdown)
Ground Current (IGND)
IOUT = 500mA; VIN = VOUT + 0.5V
0.1
mV
1.0
μA
μA
6
Bias Supply
2.3
BIAS Input Voltage (VBIAS)
(5)
VBIAS UVLO Threshold
1.7
VBIAS Rising
VBIAS UVLO Hysteresis
2.1
5.5
V
2.3
V
75
mV
IOUT = 100mA
1.15
V
IOUT = 500mA
1.25
2.1
V
VBIAS Supply Current (IBIAS)
IOUT = 1mA; VBIAS = VOUT + 2.1V
330
500
μA
VBIAS Supply Current in Shutdown (IBIAS)
VEN ≤ 0.2V (Regulator Shutdown)
0.1
1.0
μA
IOUT = 100mA
9
50
mV
IOUT = 500mA
44
120
mV
Dropout voltage (VBIAS - VOUT)
Output Voltage
Dropout voltage
(VIN - VOUT)
Output Voltage Accuracy
VBIAS Line Regulation
March 2010
IOUT = 100μA
-1.5
+1.5
%
IOUT = 100μA
-2.0
+2.0
%
VBIAS = VOUT + 2.1V to 5.5V
-0.1
0.1
%/V
3
0.015
M9999-032310-A
Micrel, Inc.
MIC47050
Electrical Characteristics(4)
VIN = VOUT + 0.5V; VBIAS = VOUT+2.1V; COUT = 1µF; IOUT = 100µA; TJ = 25°C, bold values indicate –40°C≤ TJ ≤ +125°C, unless noted.
Parameter
Condition
Min.
Typ.
Max.
Units
VIN Line Regulation
VIN = VOUT + 0.5V to 3.6V
-0.05
0.005
0.05
%/V
Load Regulation
IOUT = 10mA to 500mA
0.2
0.5
%
0.6
1.6
2.5
A
1.0
0.77
Current Limit
Short Circuit Current Limit
VIN = 2.7V; VOUT = 0V
Enable Input
EN Logic Level High
V
0.2
EN Logic Level Low
0.67
EN Hysteresis
100
mV
VEN ≤ 0.2V ( Regulator Shutdown)
1
μA
VEN ≥ 1.0V ( Regulator Enabled)
6
μA
COUT = 1μF; 90% of typical VOUT
15
TJ Rising
160
°C
20
°C
Enable Bias Current
Turn-on Time
500
V
μs
Thermal Protection
Over-Temperature Shutdown
Over-Temperature Shutdown Hysteresis
Power Good
Power Good Threshold Voltage
91
VOUT Rising
VOUT Falling
85
Power Good Hysteresis
Power Good Output Low Voltage
IPG = 250μA
Power Good Leakage Current
VPG = 5.0V
-1
95
%
89
%
2
%
0.02
0.1
V
0.01
+1
μA
0.406
V
0.408
V
Reference Voltage (Adjustable Option Only)
Feedback Reference Voltage
FB Bias Current
IOUT = 100μA
0.394
IOUT = 100μA
0.392
0.4
VFB = 0.8V
20
nA
f = 10Hz to 100kHz; IOUT = 100mA; COUT=1μF
63
μVRMS
f = 10kHz; COUT = 1.0μF, IOUT = 100mA
50
dB
f = 100kHz; COUT = 1.0μF, IOUT = 100mA
37
dB
Output Voltage Noise and Ripple Rejection
Output Voltage Noise
Ripple Rejection
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5kΩ in series with 100pF.
4. Specification for packaged product only.
5. Both VIN and VBIAS UVLO thresholds must be met for the output voltage to turn-on. If either of the two input voltages is below the UVLO thresholds,
the output is disabled.
March 2010
4
M9999-032310-A
Micrel, Inc.
MIC47050
Typical Characteristics
50
1.8
45
1.6
1.4
1.2
1.0
0.8
0.6
VBIAS = 5.0V
0.4
VOUT = 1.8V
0.2
0
1
2
3
40
35
30
25
20
15
10
VBIAS = 5.0V
0
200
300
400
500
1.6
1.4
IOUT = 500mA
1.0
0.8
VIN = 2.5V
0.4
2
3
4
VOUT = 2.0V
1.2
1.0
VOUT = 1.2V
0.8
0.6
0.4
VIN = 2.5V
20
40
60
1.7
80
VOUT = 2.0V
1.5
1.4
1.3
1.2
VOUT = 1.2V
1.1
VIN = 2.5V
IOUT = 500mA
0.9
0
100
200
300
400
500
-40
-20
0
20
40
60
80
BIAS VOLTAGE (V)
OUTPUT CURRENT (mA)
TEMPERATURE (°C)
Bias Current vs.
Bias Voltage
Bias Current vs.
Output Current
Bias Current vs.
Temperature
400
336
380
360
340
320
300
280
334
332
330
328
326
VBIAS = 3.6V
VIN = 1.8V
322
IOUT = 1mA
260
380
324
VIN = 1.8V
240
VOUT = 1.2V
320
3.5
4
4.5
BIAS VOLTAGE (V)
5
5.5
100 120
400
BIAS CURRENT (µA)
338
BIAS CURRENT (µA)
340
100 120
1.6
1.0
0.0
5
0
Bias Dropout Voltage vs.
Temperature
1.4
420
March 2010
-20
1.8
1.6
440
3
10
1.9
0.2
VOUT = 1.8V
0.2
VOUT = 1.2V
TEMPERATURE (°C)
DROPOUT VOLTAGE (V)
1.8
IOUT = 100mA
VBIAS = 3.6V
20
-40
1.8
DROPOUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
100
2.0
IOUT = 100mA
0.6
30
Bias Dropout Voltage vs.
Output Current
2.2
1.2
40
OUTPUT CURRENT (mA)
Output Voltage vs.
Bias Voltage
2.0
50
0
0
4
IOUT = 500mA
60
VOUT = 1.2V
INPUT VOLTAGE (V)
BIAS CURRENT (µA)
Input Dropout Voltage vs.
Temperature
70
5
IOUT = 500mA
0.0
Input Dropout Voltage vs.
Output Current
DROPOUT VOLTAGE (mV)
2.0
DROPOUT VOLTAGE (mV)
OUTPUT VOLTAGE (V)
Output Voltage vs.
Input Voltage
360
340
320
300
VBIAS = 3.6V
280
VIN = 1.8V
260
VOUT = 1.2V
240
0
100
200
300
400
OUTPUT CURRENT (mA)
5
500
-40
-20
0
20
40
60
80
100 120
TEMPERATURE (°C)
M9999-032310-A
Micrel, Inc.
MIC47050
Typical Characteristics (Continued)
Ground Current vs.
Input Voltage
Ground Current vs.
Temperature
VBIAS = 5.0V
IOUT = 500mA
20
15
10
5
0
1.2
1.6
2
2.4
2.8
INPUT VOLTAGE (V)
3.2
1.206
6.25
6.00
5.75
5.50
5.25
5.00
VBIAS = 3.6V
VIN = 1.8V
4.75
4.50
4.25
4.00
-40
3.6
-20
1.65
1.60
1.55
1.50
VBIAS = 5.0V
1.5
2
2.5
3
80
3.5
4
VBIAS = 3.6V
VIN = 1.8V
VOUT = 1.2V
-40
70
60
60
PSRR (dB)
70
50
40
VOUT = 1.2V
-20
0
0
0.01
0.1
1
10
Frequency (kHz)
March 2010
20
40
60
80
100
1000
500
1.200
1.195
VBIAS = 3.6V
1.190
VIN = 1.8V
1.185
IOUT = 100µA
1.180
100 120
-40 -20
0
20
40
60
80
100 120
TEMPERATURE (°C)
Output Noise
10
50
40
30
VBIAS = 3.6V ± 300mV
20
VIN = 1.8V
10
IOUT = 500mA
400
1.205
Power Supply Ripple Rejection
(Bias Voltage)
80
300
1.210
TEMPERATURE (°C)
90
200
OUTPUT CURRENT (mA)
1.215
1.50
1.45
1.40
80
20
100
Output Voltage vs.
Temperature
1.65
1.60
1.55
90
VBIAS = 3.6V
VIN = 1.8V
0
100 120
1.80
1.75
1.70
Power Supply Ripple Rejection
(Input Voltage)
VIN = 1.8V ± 300mV
VBIAS = 3.6V
1.220
INPUT VOLTAGE (V)
30
1.194
1.190
60
1.35
1.30
VOUT = 1.2V
1.40
1.196
IOUT = 500mA
OUTPUT VOLTAGE (V)
CURRENT LIMIT (A)
1.70
1.45
1.198
1.192
1.90
1.85
1.75
PSRR (dB)
40
1.200
Current Limit vs.
Temperature
1.80
10
20
1.202
TEMPERATURE (°C)
Current Limit vs.
Input Voltage
CURRENT LIMIT (A)
0
1.204
VOUT = 1.2V
OUTPUT NOISE (µV/√Hz)
GROUND CURRENT (µA)
GROUND CURRENT (µA)
VOUT = 1.2V
25
1.208
7.00
6.75
6.50
OUTPUT VOLTAGE (V)
30
Output Voltage vs.
Output Current
VOUT = 1.2V
0.1
0.1
VBIAS = 3.6V
0.01
VIN = 1.8V
VOUT = 1.2V
Noise (10Hz-100kHz) = 56.19µVRMS
IOUT = 500mA
0
0.01
1
1
10
Frequency (kHz)
6
100
1000
0.001
0.01
0.1
1
10
100
1000
FREQUENCY (kHz)
M9999-032310-A
Micrel, Inc.
MIC47050
Functional Characteristics
March 2010
7
M9999-032310-A
Micrel, Inc.
MIC47050
Functional Diagram
MIC47050 Fixed Output Block Diagram
MIC47050 Adjustable Output Block Diagram
March 2010
8
M9999-032310-A
Micrel, Inc.
MIC47050
Functional Description
The MIC47050 is a high-speed, ultra-low dropout, dual
supply NMOS ULDO™ designed to take advantage of
point-of-load applications that use multiple supply rails to
generate a low voltage, high current power supply. The
MIC47050 can source 0.5A of output current while only
requiring a 1µF ceramic output capacitor for stability.
The MIC47050 regulator is fully protected from damage
due to fault conditions, offering linear current limiting and
thermal shutdown.
capacitors have a very stable dielectric (10% over their
operating temperature range) and can also be used with
this device. See “Typical Characteristic” for examples of
load transient response.
Output Capacitor
The MIC47050 requires an output capacitor of 1µF or
greater to maintain stability. The design is optimized for
use with low-ESR ceramic chip capacitors. High ESR
capacitors may cause high frequency oscillation. The
output capacitor can be increased, but performance has
been optimized for a 1µF ceramic output capacitor and
does not improve significantly with larger capacitance.
The output capacitor type and placement criteria are the
same as the input capacitor. See the input capacitor
subsection for a detailed description.
Bias Supply Voltage
VBIAS, requiring relatively light current, provides power to
the control portion of the MIC47050. Bypassing on the
bias pin is recommended to improve performance of the
regulator during line and load transients. Small 0.1µF
ceramic capacitors from VBIAS-to-ground help reduce
high frequency noise from being injected into the control
circuitry from the bias rail and are good design practice.
Minimum Load Current
The MIC47050, unlike most other regulators, does not
require a minimum load to maintain output voltage
regulation.
Input Supply Voltage
VIN provides the supply to power the LDO. The minimum
input voltage is 1.0V. This allows conversion from low
voltage supplies to reduce the power dissipation in the
pass element.
Adjustable Regulator Design
The MIC47050 adjustable version allows programming
the output voltage from 0.4V to 2.0V. Two external
resistors are required. The R1 resistor value between
VOUT and the ADJ pin should not exceed 10kΩ, as larger
values can cause instability. R2 connects between the
ADJ pin and ground. The resistor values are calculated
as follows:
Input Capacitor
The MIC47050 is a high-performance, high bandwidth
device. Therefore, it requires a well-bypassed input
supply for optimal performance. A 1µF capacitor is the
minimum required for stability. A 10µF ceramic capacitor
is recommended for most applications, especially if the
LDO’s headroom (VIN –VOUT) is small and/or large load
transients are present. Fast load transient and low
headroom requires a larger input filter capacitor to
ensure that the regulator does not drop out of regulation.
A 10µF will better attenuate any voltage glitches from
exceeding the maximum voltage rating of the part.
Additional high-frequency capacitors, such as smallvalued NPO dielectric-type capacitors, help filter out
high-frequency noise and are good practice in any RFbased circuit.
X7R and X5R dielectric ceramic capacitors are
recommended
because
of
their
temperature
performance. X7R-type capacitors change capacitance
by 15% over their operating temperature range and are
the most stable type of ceramic capacitors. Z5U and
Y5V dielectric capacitors are not recommended since
they change value by as much as 50% and 60%
respectively over their operating temperature ranges. To
use a ceramic-chip capacitor with Y5V dielectric, the
value must be much higher than an X7R ceramic or a
tantalum capacitor to ensure the same capacitance
value over the operating temperature range. Tantalum
March 2010
⎞
⎛V
R1 = R2 × ⎜ OUT − 1⎟
⎟
⎜V
⎝ REF ⎠
Where VOUT is the desired output voltage and VREF is the
internal reference voltage.
Enable/Shutdown
The MIC47050 comes with a single active-high enable
pin that allows the regulator to be disabled. Forcing the
enable pin low disables the regulator and sends it into a
“zero” off-mode-current state. In this state, current
consumed by the regulator goes nearly to zero. Forcing
the enable pin high enables the output voltage. The
active-high enable pin uses CMOS technology and the
enable pin cannot be left floating; a floating enable pin
may cause an indeterminate state on the output.
9
M9999-032310-A
Micrel, Inc.
MIC47050
Power Good
The PGOOD pin is an open drain output that goes low
when the output voltage (fixed version) drops below the
PGOOD threshold voltage.
The pull-up resistor value should be large enough to
guarantee a proper “low” voltage when the PGOOD pin
pulls low. The PGOOD low voltage is typically 0.1V at
250uA current. A 10k resistor or greater is
recommended when pulling up to 3.3V bias.
If the Power Good function is not required, the PGOOD
pin may be left unconnected.
TJ(MAX) = 125°C, the maximum junction temperature of
the die.
θJA thermal resistance = 90°C/W.
Table 1 shows junction-to-ambient thermal resistance for
the MIC47050 in the MLF® package.
Table 1. Thermal Resistance
Package
6-pin 2mm x 2mm MLF®
Thermal Shutdown
The MIC47050 has an internal over-temperature
protection feature. This feature is for protection only.
The device should never be intentionally operated near
this temperature as this may reduce long term reliability.
The device will turn off when the over-temperature
threshold is exceeded. A 20°C hysteresis is built in to
allow the device to cool before turning back on.
TA = 125°C − 90°C/W × 0.3W
TA = 98°C
Therefore, a 1.2V application with 0.5A of output current
can accept an ambient operating temperature of 98°C in
a 2mm x 2mm MLF® package.
)
Because this device is CMOS, the ground current is
insignificant for power dissipation and can be ignored for
this calculation.
Thermal Measurements
Measuring the IC’s case temperature is recommended to
insure it is within its operating limits. Although this might
seem like a very elementary task, it is easy to get
erroneous results. The most common mistake is to use
the standard thermal couple that comes with a thermal
meter. This thermal couple wire gauge is large, typically
22 gauge, and behaves like a heatsink, resulting in a
lower case measurement.
Two methods of temperature measurement are using a
smaller thermal couple wire or an infrared thermometer.
If a thermal couple wire is used, it must be constructed
of 36 gauge wire or higher (smaller wire size) to
minimize the wire heat-sinking effect. In addition, the
thermal couple tip must be covered in either thermal
grease or thermal glue to make sure that the thermal
couple junction is making good contact with the case of
the IC. Omega brand thermal couple (5SC-TT-K-36-36)
is adequate for most applications.
)
PD = 1.8V − 1.2V × 0.5A = 0.3W
To determine the maximum ambient operating
temperature of the package, use the junction-to-ambient
thermal resistance of the device and the following basic
equation:
PD(MAX) =
March 2010
45°C/W
TA = TJ(MAX) − Θ JA × PD(MAX)
PD = VIN − VOUT × IOUT + VIN × IGND + VBIAS × IBIAS
(
θJC
Substituting PD for PD(max) and solving for the ambient
operating temperature will give the maximum operating
conditions for the regulator circuit. The junction-toambient thermal resistance for the minimum footprint is
90°C/W. The maximum power dissipation must not be
exceeded for proper operation. For example, when
operating the MIC47050-1.2YML at an input voltage of
1.8V and a 0.5A load with a minimum footprint layout,
the maximum ambient operating temperature TA can be
determined as follows:
Thermal Considerations
The MIC47050 is designed to provide 0.5A of continuous
current in a very small package. Maximum ambient
operating temperature can be calculated based on the
output current and the voltage drop across the part.
Given that the input voltage is 1.8V, the output voltage is
1.2V and the output current is 0.5A. The actual power
dissipation of the regulator circuit can be determined
using the equation:
(
θJA Recommended
Min. Footprint
90°C/W
⎡ TJ(MAX) − TA ⎤
⎢
⎥
Θ JA
⎢⎣
⎥⎦
10
M9999-032310-A
Micrel, Inc.
MIC47050
Wherever possible, an infrared thermometer is
recommended. The measurement spot size of most
infrared thermometers is too large for an accurate
reading on a small form factor ICs. However, a IR
thermometer from Optris has a 1mm spot size, which
makes it a good choice for the 2mm x 2mm MLF®
package. An optional stand makes it easy to hold the
beam on the IC for long periods of time.
For a full discussion of heat sinking and thermal effects
of voltage regulators, refer to the “Regulator Thermals”
section of Micrel’s Designing with Low-Dropout Voltage
Regulators handbook. This information can be found on
Micrel's website at:
http://www.micrel.com/_PDF/other/LDOBk_ds.pdf
March 2010
11
M9999-032310-A
Micrel, Inc.
MIC47050
MIC47050 Typical Application Schematic
MIC47050 Adjustable Output
MIC47050 Fixed Output
March 2010
12
M9999-032310-A
Micrel, Inc.
MIC47050
MIC47050 Bill of Materials
Item
C1
C2
C3
Part Number
GRM21BR60J106ME19
C1608X5R0J106MT
GRM155R61A105KE15D
Manufacturer
Murata
TDK
(1)
Ceramic Capacitor, 10µF, 6.3V, X5R, 0603 size
(2)
Ceramic Capacitor, 10µF, 6.3V, X5R, 0603 size
Murata(1)
Capacitor, 1µF, 10V, X5R, 0402 size
(2)
C1005X5R0J105KT
TDK
06035D104MAT2A
AVX(3)
Description
Capacitor, 1µF, 10V, X5R, 0402 size
Ceramic Capacitor, 0.1µF, 50V, X5R, 0603 size
(4)
Qty.
1
1
1
R1
CRCW06031001FRT1
Vishay Dale
Resistor, 1k (0603 size), 1%
1
R2
CRCW06036650FRT1
Vishay Dale(4)
Resistor, 665 (0603 size), 1%
1
R3
CRCW06031002FRT1
Vishay Dale(4)
Resistor, 10k (0603 size), 1%
1
U1
MIC47050YML
MIC47050-1.2YML
Micrel, Inc.(5)
Low Input and Output 500mA ULDO™ - Adjustable Output
Low Input and Output 500mA ULDO™ - Fixed 1.2V Output
1
Notes:
1. Murata: www.murata.com.
2. TDK: www.tdk.com.
3. AVX: www.avx.com.
4. Vishay: www.vishay.com .
5. Micrel, Inc.: www.micrel.com.
March 2010
13
M9999-032310-A
Micrel, Inc.
MIC47050
Package Information
6-pin 2mm x 2mm MLF® (ML)
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its
use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product
can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant
into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A
Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully
indemnify Micrel for any damages resulting from such use or sale.
© 2010 Micrel, Incorporated.
March 2010
14
M9999-032310-A