MICREL SY89843U_10

SY89843U
Precision LVPECL Runt Pulse Eliminator 2:1
MUX with 1:2 Fanout and Internal Termination
General Description
The SY89843U is a low jitter PECL, 2:1 differential input
multiplexer (MUX) optimized for redundant source
switchover applications. Unlike standard multiplexers,
the SY89843U unique 2:1 Runt Pulse Eliminator (RPE)
MUX prevents any short cycles or “runt” pulses during
switchover. In addition, a unique Fail-Safe Input
protection prevents metastable conditions when the
selected input clock fails to a DC voltage (voltage
between the pins of the differential input drops below
100mV).
The differential input includes Micrel’s unique, 3-pin
input termination architecture that allows customers to
interface to any differential signal (AC- or DC-coupled)
as small as 100mV (200mVPP) without any level shifting
or termination resistor networks in the signal path. The
output is 800mV, 100K compatible LVPECL with fast
rise/fall times guaranteed to be less than 190ps.
The SY89843U operates from a 2.5V ±5% or 3.3V
±10% supply and is guaranteed over the full industrial
temperature range of –40°C to +85°C. The SY89843U is
®
part of Micrel’s high-speed, Precision Edge product
line. All support documentation can be found on Micrel’s
web site at: www.micrel.com.
Precision Edge
®
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
Selects between two sources, and provides a
glitch-free, stable LVPECL output
Guaranteed AC performance over temperature
and supply voltage:
– Wide operating frequency: 1kHz to >1.5GHz
– < 880ps In-to-Out tpd
– < 190ps tr/tf
Unique patent-pending input isolation design
minimizes crosstalk
Fail-Safe Input prevents oscillations
Ultra-low jitter design:
– <1psRMS random jitter
– <1psRMS cycle-to-cycle jitter
– <10psPP total jitter (clock)
– <0.7psRMS MUX crosstalk induced jitter
Unique patent-pending input termination and VT
pin accepts DC- and AC-coupled inputs (CML,
PECL, LVDS)
800mV LVPECL output swing
2.5V ±5% or 3.3V ±10% supply voltage
–40°C to +85°C industrial temperature range
Available in 24-pin (4mm x 4mm) QFN package
Applications
•
•
Redundant clock switchover
Failsafe clock protection
Markets
•
•
•
•
LAN/WAN
Enterprise servers
ATE
Test and measurement
Precision Edge is a registered trademark of Micrel, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
May 2007
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Typical Application
Simplified Example Illustrating RPE (Runt Pulse Elimination)
Circuit when Primary Clock Fails
May 2007
2
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Ordering Information(1)
Part Number
Package Type
SY89843UMG
(2)
SY89843UMGTR
Operating Range
Package Marking
Lead Finish
QFN-24
Industrial
843U with bar-line
Pb-Free indicator
NiPdAu
Pb-Free
QFN-24
Industrial
843U with bar-line
Pb-Free indicator
NiPdAu
Pb-Free
Notes:
1. Contact factory for die availability. Dice are guaranteed at TA = 25°C, DC Electricals Only.
2. Tape and Reel.
Pin Configuration
24-Pin QFN
May 2007
3
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Pin Description
Pin Number
Pin Name
Pin Function
5, 2
23, 20
IN0, /IN0,
IN1, /IN1
Differential Inputs: These input pairs are the differential signal inputs to the
device. These inputs accept AC- or DC-coupled signals as small as 100mV
(200mVPP). Each pin of a pair internally terminates to a VT pin through 50Ω.
Please refer to the “Input Interface Applications” section for more details.
VT0, VT1
Input Termination Center-Tap: Each side of the differential input pair terminates
to a VT pin. The VT0 and VT1 pins provide a center-tap to a termination network
for maximum interface flexibility. Please refer to the “Input Interface Applications”
section for more details.
3, 21
VREF-AC0
VREF-AC1
Reference Voltage: These outputs bias to VCC–1.2V. They are used for ACcoupling inputs IN and /IN. Connect VREF-AC directly to the corresponding VT
pin. Bypass with 0.01µF low ESR capacitor to VCC. Maximum sink/source current
is ±1.5mA. Please refer to the “Input Interface Applications” section for more
details.
15
SEL
This single-ended TTL/CMOS-compatible input selects the inputs to the
multiplexer. Note that this input is internally connected to a 25k Ω pull-up resistor
and will default to logic HIGH state if left open.
1, 6, 9, 10,
13, 19, 24
VCC
Positive Power Supply: Bypass with 0.1µF//0.01µF low ESR capacitors as close
to VCC pins as possible.
7, 8
11, 12
Q0, /Q0
Q1, /Q1
14, 17, 18
GND
Exposed Pad
4, 22
16
CAP
Differential Outputs: These differential LVPECL outputs are a logic function of the
IN0, IN1, and SEL inputs. Please refer to the truth table below for details.
Ground: Ground pin and exposed pad must be connected to the same ground
plane.
Power-On Reset (POR) Initialization capacitor. When using the multiplexer with
RPE capability, the pin is tied to a capacitor to VCC. The purpose is to ensure the
internal RPE logic starts up in a known state. See “Power-On Reset (POR)
Description” section for more details regarding capacitor selection. If this pin is
tied directly to VCC, the RPE function will be disabled and the multiplexer will
function as a normal multiplexer. The CAP pin should never be left open.
Truth Table
INPUTS
May 2007
OUTPUTS
IN0
/IN0
IN1
/IN1
SEL
Q
/Q
0
1
X
X
0
0
1
1
0
X
X
0
1
0
X
X
0
1
1
0
1
X
X
1
0
1
1
0
4
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Absolute Maximum Ratings(1)
Operating Ratings(2)
Supply Voltage (VCC) .............................................. –0.5V to +4.0V
Input Voltage (VIN) ......................................................–0.5V to VCC
LVPECL Output Current (IOUT)
Continuous .................................................................. ±50mA
Surge ........................................................................ ±100mA
Termination Current
Source/Sink Current on VT ........................................ ±100mA
Input Current
Source/sink current on IN, /IN ..................................... ±50mA
VREF-AC Current
Source/sink current on VREF-AC ...................................... ±2mA
Lead Temperature (soldering, 20 sec.) ..............................+260°C
Storage Temperature (Ts) .................................... –65°C to 150°C
Supply Voltage (VCC) .............................+2.375V to +2.625V
...............................................................+3.0V to +3.6V
Ambient Temperature (TA) ........................... –40°C to +85°C
(3)
Package Thermal Resistance
QFN (θJA)
Still-Air ............................................................... 50°C/W
QFN (ΨJB)
Junction-to-Board .............................................. 30°C/W
DC Electrical Characteristics(4)
TA = –40°C to +85°C; unless otherwise stated.
Symbol
Parameter
VCC
Power Supply
ICC
Power Supply Current
RIN
Input Resistance
(IN-to-VT)
RDIFF_IN
Condition
Min
Typ
Max
Units
2.375
3.0
2.5
3.3
2.625
3.6
V
V
70
100
mA
45
50
55
Ω
Differential Input Resistance
(IN-to-/IN)
90
100
110
Ω
VIH
Input High Voltage
(IN, /IN)
1.2
VCC
V
VIL
Input Low Voltage
(IN, /IN)
0
VIH–0.1
V
VIN
Input Voltage Swing
(IN, /IN)
See Figure 1a. Note 5
0.1
VCC
V
VDIFF_IN
Differential Input Voltage Swing
|IN-/IN|
See Figure 1b.
0.2
VIN_FSI
Input Voltage Threshold that triggers
FSI
VT_IN
IN-to-VT
(IN, /IN)
VREF-AC
Output Reference Voltage
No load, max VCC.
V
30
VCC–1.3
VCC–1.2
100
mV
1.28
V
VCC–1.1
V
Notes:
1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not
implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings.
3. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the devices most negative potential on the PCB. θJA and ΨJB
values are determined for a 4-layer board in still air unless otherwise stated.
4. The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established.
5. VIN (max) is specified when VT is floating.
May 2007
5
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
LVPECL Outputs DC Electrical Characteristics(6)
VCC = 2.5V ±5% or 3.3V ±10%, RL = 50Ω to VCC-2V; TA = -40°C to + 85°C, unless otherwise stated.
Symbol
Parameter
Condition
Min
Typ
Max
VOH
Output HIGH Voltage
Q, /Q
VCC-1.145
VCC–0.895
Units
V
VOL
Output Low Voltage
Q, /Q
VCC-1.945
VCC–1.695
V
VOUT
Output Voltage Swing
Q, /Q
See Figure 1a.
550
800
mV
VDIFF-OUT
Differential Output Voltage Swing
Q, /Q
See Figure 1b.
1100
1600
mV
LVTTL/CMOS DC Electrical Characteristics(6)
VCC = 2.5V ±5% or 3.3V ±10%; TA = -40°C to + 85°C, unless otherwise stated.
Symbol
Parameter
Condition
Min
VIH
Input HIGH Voltage
VIL
Input LOW Voltage
IIH
Input HIGH Current
-125
IIL
Input LOW Current
-300
Typ
Max
2.0
Units
V
0.8
V
30
µA
µA
Note:
6.
The circuit is designed to meet the DC specifications shown in the above table after thermal equilibrium has been established.
May 2007
6
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
AC Electrical Characteristics(7)
VCC = 2.5V ±5% or 3.3V ±10%, RL = 50Ω to VCC–2V; TA = –40°C to + 85°C, unless otherwise stated.
Symbol
Parameter
Condition
Min
fMAX
Maximum Operating Frequency
VOUT ≥ 400mV
1.5
2.0
tpd
Differential Propagation Delay In-to-Q
100mV < VIN ≤ 200mV
480
600
880
ps
In-to-Q
200mV < VIN ≤ 800mV
430
575
780
ps
17
cycles
900
ps
(8, 9)
(8, 9)
SEL-to-Q
RPE enabled, see Timing Diagram
SEL-to-Q
RPE disabled (VSEL = VCC/2)
Typ
550
Max
Units
GHz
tpd
Tempco
Differential Propagation Delay
Temperature Coefficient
tSKEW
Output-to-Output Skew
Within device
20
ps
Part-to-Part Skew
Note 11
200
ps
1
psRMS
tJITTER
tr, tf
o
410
(10)
fs/ C
Clock
Random Jitter
Note 12
Cycle-to-Cycle Jitter
Note 13
1
psRMS
Total Jitter
Note 14
10
psPP
Crosstalk-induced Jitter
Note 15
0.7
psRMS
Output Rise/Fall Time (20% to 80%)
At full output swing.
190
ps
70
Notes:
7.
High-frequency AC-parameters are guaranteed by design and characterization.
8.
Propagation delay is measured with input tr, tf ≤ 300ps (20% to 80%) and VIL ≥ 800mV.
9.
Propagation delay is a function of the rise and fall times at IN. See “Typical Operating Characteristics” for details.
10. Output-to-output skew is measured between two different outputs under identical conditions.
11. Part-to-part skew is defined for two parts with identical power supply voltages at the same temperature and with no skew of the edges at
the respective inputs.
12. Random jitter is measured with a K28.7 character pattern, measured at <fMAX.
13. Cycle-to-cycle jitter definition: The variation of periods between adjacent cycles, Tn – Tn-1 where T is the time between rising edges of the
output signal.
14. Total jitter definition: with an ideal clock input of frequency <fMAX, no more than one output edge in 1012 output edges will deviate by more
than the specified peak-to-peak jitter value.
15. Crosstalk is measured at the output while applying two similar differential clock frequencies that are asynchronous with respect to each
other at the inputs.
May 2007
7
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Functional Description
RPE MUX and Fail-Safe Input
The SY89843U is optimized for clock switchover
applications where switching from one clock to
another clock without runt pulses (short cycles) is
required. It features two unique circuits:
Runt-Pulse Eliminator (RPE) Circuit:
The RPE MUX provides a “glitchless” switchover
between two clocks and prevents any runt pulses
from occurring during the switchover transition. The
design of both clock inputs is identical (i.e., the
switchover sequence and protection is symmetrical
for both input pair, IN0 or IN1. Thus, either input pair
may be defined as the primary input). If not required,
the RPE function can be permanently disabled to
allow the switchover between inputs to occur
immediately. If the CAP pin is tied directly to VCC,
then the RPE function will be disabled and the
multiplexer will function as a normal multiplexer.
Fail-Safe Input (FSI) Circuit:
The FSI function provides protection against a
selected input pair that drops below the minimum
amplitude requirement. If the selected input pair
drops sufficiently below the 100mV minimum singleended input amplitude limit (VIN), or 200mV
differentially (VDIFF_IN), then the output will latch to
the last valid clock state.
RPE and FSI Functionality
The basic operation of the RPE MUX and FSI
functionality is described with the following four case
descriptions. All descriptions are related to the true
inputs and outputs. The primary (or selected) clock
is called CLK1; the secondary (or alternate) clock is
called CLK2. Due to the totally asynchronous
relation of the IN and SEL signals and an additional
internal protection against metastability, the number
of pulses required for the operations described in
cases 1-4 can vary within certain limits. Refer to
“Timing Diagrams” for more detailed information.
Case #1 Two Normal Clocks and RPE Enabled
In this case, the frequency difference between the
two running clocks IN0 and IN1 must not be greater
than 1.5:1. For example, if the IN0 clock is 500MHz,
the IN1 clock must be within the range of 334MHz to
750MHz.
If the SEL input changes state to select the alternate
clock, then the switchover from CLK1 to CLK2 will
occur in three stages.
•
•
•
Stage 1: The output will continue to follow
CLK1 for a limited number of pulses.
Stage 2: The output will remain LOW for a
limited number of pulses of CLK2.
Stage 3: The output follows CLK2.
Timing Diagram 1
May 2007
8
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Case #2 Input Clock Failure: Switching from a
selected clock stuck HIGH to a valid clock (RPE
enabled).
If CLK1 fails HIGH before the RPE MUX selects
CLK2 (using the SEL pin), then the switchover will
occur in three stages.
•
Stage 1: The output will remain HIGH for a
limited number of pulses of CLK2.
Stage 2: The output will switch to LOW and
then remain LOW for a limited number of
falling edges of CLK2.
Stage 3: The output will follow CLK2
•
•
Timing Diagram 2
Note:
Output shows extended clock cycle during switchover. Pulse width for both high and low of this cycle will always be greater than 50% of
the CLK2 period.
May 2007
9
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Case #3 Input Clock Failure: Switching from a
selected clock stuck Low to a valid clock (RPE
enabled).
If CLK1 fails LOW before the RPE MUX selects CLK2
(using the SEL pin), the switchover will occur in two
stages.
•
Stage 1: The output will remain LOW for a
limited number of falling edges of CLK2.
Stage 2: The output will follow CLK2.
•
Timing Diagram 3
May 2007
10
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Case #4 Input Clock Failure: Switching from the
selected clock input stuck in an undetermined state
to a valid clock input (RPE enabled).
If CLK1 fails to an undetermined state (e.g.,
amplitude falls below the 100mV (VIN) minimum
single-ended input limit, or 200mV differentially)
before the RPE MUX selects CLK2 (using the SEL
pin), the switchover to the valid clock CLK2 will
occur either following Case #2 or Case #3,
depending upon the last valid state at the CLK1.
If the selected input clock fails to a floating, static, or
extremely low signal swing, including 0mV, the FSI
function will eliminate any metastable condition and
guarantee a stable output signal. No ringing and no
undetermined state will occur at the output under
these conditions.
Please note that the FSI function will not prevent
duty cycle distortions or runt pulses in case of a
slowly deteriorating (but still toggling) input signal.
Due to the FSI function, the propagation delay will
depend on rise and fall time of the input signal and
on its amplitude. Refer to “Typical Operating
Characteristics” for more detailed information.
Timing Diagram 4
Power-On Reset (POR) Description
The SY89843U includes an internal power-on reset
(POR) function to ensure the RPE logic starts-up in
a known logic state once the power-supply voltage is
stable. An external capacitor connected between
VCC and the CAP pin (pin 16) controls the delay for
the power-on reset function.
Calculating the required capacitor value is based on
the time the system power supply needs to power up
to a minimum of 2.3V. The time constant for the
internal power-on-reset must be greater than the
time required for the power supply to ramp up to a
minimum of 2.3V.
May 2007
The following equation describes this relationship:
C(µF)
≥
t dPS ( ms )
12( ms / µF )
As an example, if the time required for the system
power supply to power up past 2.3V is 12ms, the
required capacitor value on pin 16 would be:
11
C(µF) ≥
12ms
12( ms / µF )
C(µF) ≥
1µF
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Typical Operating Characteristics
VCC = 3.3V, GND = 0V, VIN ≥ 400mVpk, tr/tf ≤ 300ps, RL = 50Ω to VCC–2V, TA = 25°C, unless otherwise stated.
May 2007
12
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Functional Characteristics
VCC = 3.3V, GND = 0V, VIN ≥ 400mVpk, tr/tf ≤ 300ps, RL = 50Ω to VCC–2V, TA = 25°C, unless otherwise stated.
May 2007
13
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Singled-Ended and Differential Swings
Figure 1b. Differential Voltage Swing
Figure 1a. Single-Ended Voltage Swing
Input and Output Stages
Figure 2a. Simplified Differential Input Stage
May 2007
Figure 2b. Simplified LVPECL Output Stage
14
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Input Interface Applications
Option: may connect VT to VCC
Figure 3a. LVPECL Interface
(DC-Coupled)
Figure 3b. LVPECL Interface
(AC-Coupled)
Figure 3d. CML Interface
(AC-Coupled)
Figure 3e. LVDS Interface
May 2007
15
Figure 3c. CML Interface
(DC-Coupled)
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
LVPECL Output Interface Applications
LVPECL has a high input impedance, a very low output
impedance (open emitter), and a small signal swing
which results in low EMI. LVPECL is ideal for driving
50Ω and 100Ω controlled impedance transmission
lines. There are several techniques for terminating the
LVPECL output: parallel termination-thevenin
equivalent, parallel termination (3-resistor), and ACcoupled termination. Unused output pairs may be
left floating. However, single-ended outputs must
be terminated, or balanced.
Figure 4a. Parallel Termination-Thevenin Equivalent
Figure 4b. Parallel Termination (3-Resistor)
Related Product and Support Documentation
Part Number
Function
Data Sheet Link
SY89844U
Precision LVDS Runt Pulse Eliminator 2:1
MUX with 1:2 Fanout and Internal
Termination
www.micrel.com/product-info/products/sy89844u.shtml
SY89845U
Precision CML Runt Pulse Eliminator 2:1
MUX with 2:1 Fanout and Internal
Termination
www.micrel.com/product-info/products/sy89845u.shtml
HBW Solutions
New Products and Applications
www.micrel.com/product-info/products/solutions.shtml
May 2007
16
M9999-052207-B
[email protected] or (408) 955-1690
Micrel, Inc.
SY89843U
Product Information
24-Pin QFN
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for
its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a
product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for
surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant
injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk
and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale.
© 2005 Micrel, Incorporated.
May 2007
17
M9999-052207-B
[email protected] or (408) 955-1690