Snap Action Switch
V
General Purpose Snap Action Switch
• Industry standard design with switching currents of 10A to 21A
• Widely used for applications where long life expectancy and
high reliability is required.
• Choose from a variety of levers, terminals and operating forces.
• Right and Left Barrier options are available for the V-21 and
V-16 models
• Heat resistant versions of the V-15 and V-10 are available.
• RoHS Compliant
Ordering Information
■ Model Number Legend
V-
1 2 3
1.
2.
3.
4 5 6 7
Ratings
21:
21 A at 250 VAC
16:
16 A at 250 VAC
15:
15 A at 250 VAC
11:
11 A at 250 VAC
10:
10 A at 250 VAC
Contact Gap
None: 1 mm (F gap)
G:
0.5 mm (G gap)
Actuator
None: Pin plunger
1:
Short hinge lever
2:
Hinge lever
3:
Long hinge lever
4:
Simulated roller lever
5:
Short hinge roller lever
6:
Hinge roller lever
8
9
4. Contact Form
COM Terminal, Bottom position:
1:
SPDT
2:
SPST-NC
3:
SPST-NO
COM Terminal, Side position:
4:
SPDT
5:
SPST-NC
6:
5.
7.
Note: These OF values are for
the pin plunger models.
8.
Special Purpose
None: Standard
T:
Heat resistive
(V-15 and V-10, only)
SPST-NO
Terminals
A:
Solder terminals
C2:
Quick-connect terminal (#187)
C:
Quick-connect terminal (#250)
Maximum Operating Force
6:
400 gf
5:
200 gf
4:
100 gf
9.
Mounting Hole Size
None: 3.1 mm
K:
2.9 mm
6. Insulation Barrier
None: Without Barrier
R:
Right-hand barrier
L:
Left-hand barrier
(Barriers available for V-21 and V-16, only)
Note: Consult Omron regarding nominclature combinations and part numbers
not found in this datasheet.
Snap Action Switch
V
121
■ Available Combinations
Thermoplastic case
V-21
V-16
V-11
V-15
V-10
Rated Current
21 A
16 A
11 A
15 A
10 A
OF
COM
Insulation
Heat
terminal
Barrier Resistance Terminal Symbol
position
Bottom
No
Standard
(80°C)
Heat
resistant
(150°C)
Yes
Side
No
Standard
(80°C)
Standard
(80°C)
Thermosetting case
Model
400 gf
400 gf
200 gf
100 gf
400 gf
200 gf
200 gf
100 gf
Solder terminals (A)
---
❍
❍
❍
❍
❍
❍
❍
Quick-connect
terminals (#187)(C2)
---
❍
❍
❍
❍
❍
❍
❍
Quick-connect
terminals (#250)(C)
❍
❍
❍
❍
❍
❍
❍
❍
Solder terminals (A)
---
---
---
---
❍
❍
❍
❍
Quick-connect
terminals (#187)(C2)
---
---
---
---
❍
❍
❍
❍
Quick-connect
terminals (#250)(C)
---
---
---
---
---
---
---
---
Solder terminals (A)
---
❍
❍
---
---
---
---
---
Quick-connect
terminals (#187)(C2)
---
❍
❍
---
---
---
---
---
Quick-connect
terminals (#250)(C)
❍
❍
❍
---
---
---
---
---
Solder terminals (A)
---
---
---
---
❍
❍
❍
❍
Quick-connect
terminals (#187)(C2)
---
---
---
---
❍
❍
❍
❍
Quick-connect
terminals (#250)(C)
❍
---
---
---
---
---
---
---
Note: 1. ❍: Available model.
Consult OMRON for specific models with standard approval.
■ List of Models
Thermoplastic Case
21 A (OF: 400 gf)
Without barrier
Common
terminal Contact
position form
Bottom
SPDT
SPST-NC
Right-hand
barrier
Without barrier
Left-hand barrier
Terminal style Actuator
Quick-connect
(#250) (C)
Pin plunger
SPST-NO
SPDT
V-21-1C6
V-21-1CR6
V-21-1CL6
V-21-2C6
V-21-2CR6
V-21-2CL6
V-21-3C6
V-21-3CR6
V-21-3CL6
Short hinge lever
V-211-1C6
V-211-1CR6
V-211-1CL6
Hinge lever
V-212-1C6
V-212-1CR6
V-212-1C6
Long hinge lever
V-213-1C6
V-213-1CR6
V-213-1CL6
Simulated roller lever
V-214-1C6
V-214-1CR6
V-214-1CL6
Short hinge roller lever
V-215-1C6
V-215-1CR6
V-215-1CL6
Hinge roller lever
V-216-1C6
V-216-1CR6
V-216-1CL6
Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate
location to obtain 2.9 mm mounting holes. Example: V-21G2-1C6-K
2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet.
122
Snap Action Switch
V
16 A (OF: 200 gf)
Without barrier
Common
terminal Contact
position form
Bottom
SPDT
SPST-NC
SPST-NO
SPDT
Terminal style
A
C2
C
A
C2
C
A
C2
C
A
C2
C
A
C2
C
A
C2
C
A
C2
C
A
C2
C
A
C2
C
Left-hand barrier
Right-hand
barrier
Without barrier
Actuator
Pin plunger
Short hinge lever
Hinge lever
Long hinge lever
Simulated roller lever
Short hinge roller lever
Hinge roller lever
V-16-1A5
V-16-1C25
V-16-1C5
V-16-2A5
V-16-2C25
V-16-2C5
V-16-3A5
V-16-3C25
V-16-3C5
V-161-1A5
V-161-1C25
V-161-1C5
V-162-1A5
V-162-1C25
V-162-1C5
V-163-1A5
V-163-1C25
V-163-1C5
V-164-1A5
V-164-1C25
V-164-1C5
V-165-1A5
V-165-1C25
V-165-1C5
V-166-1A5
V-166-1C25
V-166-1C5
V-16-1AR5
V-16-1C2R5
--V-16-2AR5
V-16-2C2R5
--V-16-3AR5
V-16-3C2R5
--V-161-1AR5
V-161-1C2R5
--V-162-1AR5
V-162-1C2R5
--V-163-1AR5
V-163-1C2R5
--V-164-1AR5
V-164-1C2R5
--V-165-1AR5
V-165-1C2R5
--V-166-1AR5
V-166-1C2R5
---
V-16-1AL5
V-16-1C2L5
--V-16-2AL5
V-16-2C2L5
--V-16-3AL5
V-16-3C2L5
--V-161-1AL5
V-161-1C2L5
--V-162-1AL5
V-162-1C2L5
--V-163-1AL5
V-163-1C2L5
--V-164-1AL5
V-164-1C2L5
--V-165-1AL5
V-165-1C2L5
--V-166-1AL5
V-166-1C2L5
---
11 A (OF: 100 gf)
Without barrier
Common
terminal
position
Bottom
Contact form
SPDT
Terminal style
A
C2
C
A
C2
C
A
C2
C
A
C2
C
A
C2
C
A
C2
C
A
C2
C
Actuator
Pin plunger
Short hinge lever
Hinge lever
Long hinge lever
Simulated roller lever
Short hinge roller lever
Hinge roller lever
V-11-1A4
V-11-1C24
V-11-1C4
V-111-1A4
V-111-1C24
V-111-1C4
V-112-1A4
V-112-1C24
V-112-1C4
V-113-1A4
V-113-1C24
V-113-1C4
V-114-1A4
V-114-1C24
V-114-1C4
V-115-1A4
V-115-1C24
V-115-1C4
V-116-1A4
V-116-1C24
V-116-1C4
Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate
location to obtain 2.9 mm mounting holes. Examples: 1) V-16G3-1C25-K 2) V-11G-1A4-K
2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet.
Snap Action Switch
V
123
Thermosetting Case
Standard models - 15 A / 10 A
Common Contact
terminal
form
position
Bottom
SPDT
SPST-NC
SPST-NO
Side
Bottom
SPDT
SPST-NC
SPST-NO
SPDT
Terminal style
Actuator
15 A
10 A
200 gf
A
C2
C
A
C2
A
C2
C
A
Pin plunger
A
C2
A
C2
A
C2
Short hinge lever
Hinge lever
Long hinge lever
A
C2
A
C2
Simulated roller lever
Short hinge roller lever
A
C2
Hinge roller lever
200 gf
100 gf
V-15G-1A5-K
V-15G-1C25-K
V-15G-1C5-K
V-15G-2A5-K
V-15G-2C25-K
V-15G-3A5-K
V-15G-3C25-K
V-15G-3C5-K
V-15G-4A5-K
V-15G-5A5-K
V-15G-6A5-K
V-15G1-1A5-K
V-15G1-1C25-K
V-15G2-1A5-K
V-15G2-1C25-K
V-15G3-1A5-K
V-15G3-1C25-K
V-10G-1A5-K
V-10G-1C25-K
—
V-10G-2A5-K
V-10G-2C25-K
V-10G-3A5-K
V-10G-3C25-K
—
V-10G-4A5-K
V-10G-5A5-K
V-10G-6A5-K
V-10G1-1A5-K
V-10G1-1C25-K
V-10G2-1A5-K
V-10G2-1C25-K
V-10G3-1A5-K
V-10G3-1C25-K
V-10G-1A4-K
V-10G-1C24-K
—
V-10G-2A4-K
V-10G-2C24-K
V-10G-3A4-K
V-10G-3C24-K
—
V-10G-4A4-K
V-10G-5A4-K
V-10G-6A4-K
V-10G1-1A4-K
V-10G1-1C24-K
V-10G2-1A4-K
V-10G2-1C24-K
V-10G3-1A4-K
V-10G3-1C24-K
V-15G4-1A5-K
V-15G4-1C25-K
V-15G5-1A5-K
V-15G5-1C25-K
V-10G4-1A5-K
V-10G4-1C25-K
V-10G5-1A5-K
V-10G5-1C25-K
V-10G4-1A4-K
V-10G4-1C24-K
V-10G5-1A4-K
V-10G5-1C24-K
V-15G6-1A5-K
V-15G6-1C25-K
V-10G6-1A5-K
—
V-10G6-1A4-K
V-10G6-1C24-K
Note: 1. For SPST-NC and SPST-NO with levers consult Omron.
2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet.
Heat Resistant Models (Up to 150°C) - 15 A / 10A
Common
terminal
position
Bottom
Contact
form
SPDT
Terminal style
Actuator
15 A
200 gf
Solder Terminals
(A)
10 A
100 gf
Pin plunger
V-15-1A5-T
V-10-1A4-T
Short hinge lever
V-151-1A5-T
V-101-1A4-T
Hinge lever
V-152-1A5-T
V-102-1A4-T
Long hinge lever
V-153-1A5-T
V-103-1A4-T
Simulated roller lever
V-154-1A5-T
V-104-1A4-T
Short hinge roller lever
V-155-1A5-T
V-105-1A4-T
Hinge roller lever
V-156-1A5-T
V-106-1A4-T
Note: 1. Add “G” to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add “-K” to the part number in the appropriate
location to obtain 2.9 mm mounting holes. Add “C2” to the part number in the appropriate location to obtain versions with #187 quickconnect terminals. Example: 1) V-15G1-1C25-T-K
2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet.
124
Snap Action Switch
V
Specifications
■ Ratings (reference values)
Type
V-21
V-16
V-15
V-11
V-10
Rated voltage
250 VAC
8 VDC
30 VDC
125 VDC
250 VDC
250 VAC
8 VDC
30 VDC
125 VDC
250 VDC
250 VAC
8 VDC
30 VDC
125 VDC
250 VDC
250 VAC
8 VDC
30 VDC
125 VDC
250 VDC
250 VAC
8 VDC
30 VDC
125 VDC
250 VDC
Non-inductive load
Resistive load
Lamp load
NC
NO
NC
NO
21 A
3A
21 A
5A
14 A
5A
0.6 A
0.1 A
0.3 A
0.05 A
16 A
2A
16 A
4A
10 A
4A
0.6 A
0.1 A
0.3 A
0.05 A
15 A
2A
15 A
4A
10 A
4A
0.6 A
0.1 A
0.3 A
0.05 A
11 A
1.5 A
11 A
3A
6A
3A
0.6 A
0.1 A
0.3 A
0.05 A
10 A
1.5 A
10 A
3A
6A
3A
0.6 A
0.1 A
0.3 A
0.05 A
Inductive load
Inductive load
Motor load
NC
NO
NC
NO
12 A
4A
12 A
7A
12 A
5A
0.6 A
0.1 A
0.3 A
0.05 A
10 A
3A
10 A
6A
10 A
4A
0.6 A
0.1 A
0.3 A
0.05 A
10 A
3A
10 A
6A
10 A
4A
0.6 A
0.1 A
0.3 A
0.05 A
6A
2A
6A
3A
6A
3A
0.6 A
0.1 A
0.3 A
0.05 A
6A
2A
6A
3A
6A
3A
0.6 A
0.1 A
0.3 A
0.05 A
Note: 1. The above current values are the normal current values of models with a contact gap of 1 mm (gap F), which vary with the normal current
values of models with a contact gap of 0.5 mm (gap G).
2. Inductive load has a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC).
3. Lamp load has an inrush current of 10 times the steady-state current.
4. Motor load has an inrush current of 6 times the steady-state current.
5. The ratings values apply under the following test conditions: Ambient temperature: 20±2°C, Ambient humidity: 65±5%, Operating frequency: 30 operations/min
■ Approved Standards
UL1054 (File No. E41515)
CSA C22.2 No.55 (File No. LR21642)
Rated voltage
125 VAC
250 VAC
125 VDC
250 VDC
V-21
V-16
V-15
V-11
V-10
21 A, 1/2 HP
16 A, 1/2 HP
15 A, 1/2 HP
11 A, 1/3 HP
10 A, 1/3 HP
0.6 A
0.3 A
EN 61058-1 (File No. 129608, VDE approval)
Rated voltage
250 VAC
V-21
20 (4) A
V-16
16 (4) A
EN 61058-1 (File No. T9451451, TÜV Rheinland approval)
V-11
11 (3) A
Testing conditions: 5E4 (50,000 operations), T105 (0°C to 105°C)
Rated voltage
250 VAC
250 VDC
V-15
15 A
V-10
10 A
0.3 A
Testing conditions: 5E4 (50,000 operations), T85 (0°C to 85°C)
Snap Action Switch
V
125
■ Characteristics
Operating speed
Operating frequency
0.1 mm to 1 m/s (plunger models)
Mechanical: 600 operations/minute, max.
Electrical: 30 operations/minute, max.
100 MΩ min. (at 500 VDC)
15 mΩ max.
1,000 VAC, 50/60 Hz for 1 min between terminals of the same polarity
V-21, V-16 and V-11:
2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between
each terminal and non-current-carrying metal parts
V-15 and V-10:
1,500 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between
each terminal and non-current-carrying metal parts
Malfunction: 10 to 55 Hz, 1.5-mm double amplitude
Destruction: 1,000 m/s2 (approx. 100G) max.
Malfunction:
V-21/V-16/V-15:
300 m/s2 (approx. 30G) max.
Insulation resistance
Contact resistance
Dielectric strength (see note 2)
Vibration resistance (see note 3)
Shock resistance (see note 3)
V-11/V10:
200 m/s2 (approx. 20G) max.
Mechanical: 50,000,000 operations min. (60 operations/minute)
Life expectancy
Electrical: V-21/V-16/V-15:
100,000 operations min. (30 operations/minute)
(V-15 heat resistive: 20,000 operations min. (30 ops/minute))
V-11/V-10:
300,000 operations min. (30 operations/minute)
(V-10 heat resistive: 50,000 operations min. (30 ops/minute))
Degree of protection
Degree of protection against electric shock
Proof tracking index (PTI)
Ambient operating temperature
IEC IP40
Class I
175
-25°C to 80°C (at 60% RH max.) with no icing
Ambient operating humidity
Weight
-25°C to 150°C for heat resistive models (at 60% RH max.) with no icing.
85% max. (for 5°C to 35°C)
Approx. 6.2 g (plunger models)
Note: 1. Data shown are of initial value.
2. The dielectric strength shown is measured using a separator between the switch and metal mounting plate.
3. For pin plunger models, the above values apply for use at both the free position and total travel position. For lever models, they apply at
the total travel position.
4. For testing conditions, contact your OMRON sales representative.
■ Contact Specifications
Item
Contact
V-21
V-16
V-15
Specification
Material
V-10
Silver alloy
Gap
(standard value)
Inrush current
V-11
Rivet
NC
1 mm (F gap type) or 0.5 mm (G gap type)
50 A max.
NO
Minimum applicable load
Silver
40 A max.
36 A max.
24 A max.
160 mA at 5 VDC
Note: Minimum applicable loads are indicated by N standard reference values. This value represents the failure rate at a 60% (λ60) reliability level
(JIS C5003). The equation λ60=0.5 x 10-6 / operations indicates that a failure rate of 1/2,000,000 operations can be expected at a reliability
level of 60%
126
Snap Action Switch
V
Engineering Data
■ Mechanical service life
■ Electrical service life
(Pin plunger models)
(Pin plunger models)
V-10 (0.98 N {100 gf}),
V-11
100
50
V-10 (1.96 N
{200 gf})
V-15
V-16
V-21
0.01
0
0.2 0.4
Full stroke
OT rated value
0.6 0.8 1.0 1.2 1.4 (1.6) 1.8
Operating frequency: 60 operations/min
cosφ = 1, 250 VAC
2
1
0.5
V-21
0.3
V-15
V-16
0.1
0
OT (mm)
8
12
16
20
24
2
Ambient temperature: 20±2°C
Ambient humidity: 65±5%
Operating frequency: 60 operations/min
cosφ = 1, 250 VAC
1
0.5
0.3
0
28
V-10
V-11
0.1
0.5 1 2 3 4 5 6 7 8 9 10 11 12
Switching current (A)
■ Barrier direction (V-21 and V-16)
Right-hand Barrier
Contact form
SPDT
4
5
Switching current (A)
■ Contact Form
Common
terminal
position
6
6
5
Number of operations (x10 )
200
Number of operations (x10 )
6
Number of operations (x10 )
Ambient temperature: 20±2°C
Ambient humidity: 65±5%
Without load
Operating frequency: 600 operations/min
10
V-11/-10
V-21/-16/-15
V-21/-16/-15/-10
SPST-NC*
Left-hand Barrier
SPST-NO*
Bottom type
Side type
■ Mounting Holes
All switches may be panel mounted using M3 mounting screws with
plane washers or spring washers to securely mount the switch.
Tighten the screws to a torque of 0.39 to 0.59 N·m.
*
The SPST-NC and SPST-NO contact form types listed in the
ordering information tables are for Pin Plunger models only.
For information concerning lever models consult Omron.
Two, 3.1-dia. mounting holes or
M3 screw holes
10.3 ± 0.1
22.2 ± 0.1
Snap Action Switch
V
127
Dimensions
■ Terminals
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
2. The following table is for the SPDT contact specifications. Two terminals will be available for SPST-NO or SPST-NC contact specifications.
For terminal positions, refer to the above Contact Form
3. Right-angle PCB terminal type is available with some models (not shown). Drawings will be provided if requested.
D5: Pins at right angles, to the right
D6: Pins at right angle, to the left
Terminal type
Solder Terminal
(A)
COM
bottom position
(5.5)
(4.9)
(6.5)
(6.5)
(7.7)
2.9
2.9
3.2
Note:
128
t = 0.8 (12.0)
Three, quick-connect
terminals (#250)
(5.5)
(4.9)
(6.5)
(6.5)
(7.7)
2.4
2.4
3.6
(12.0)
(10)
6.35
3.2 (see note)
6.35
3.2
4.75±0.1
4.75±0.1
2.4 dia. 1.6 dia.
Indicates the length to the
center of the 1.6-dia. holes
Snap Action Switch
t = 0.5 (10)
Three, quick-connect
terminals (#187)
(5.5)
(10)
Terminal
dimensions
Quick-connect Terminal
(#250) (C)
(5.5)
(10)
t = 0.5
Three, solder terminals
COM
side position
Quick-connect Terminal
(#187) (C2)
V
1.6-dia. terminal hole
8.1
3.95
6.35±0.1
1.65-dia. terminal hole
■ Dimensions and Operating Characteristics
Thermoplastic Case Models
➡
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
2. The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate terminals A and C2,
which are omitted from the following drawings. Refer to Terminals section for the dimensions of these terminals.
3. The @ in the model number is for the terminal code.
4. The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix “K” have a hole size of 2.9 mm.
5. The operating characteristics are for operation in the A direction (
).
Pin Plunger Models
(Without Barrier)
V-21-1 6
V-16-1 5
V-11-1 4
20.2±0.25
A
1.6
PT
+0.13
3.1 –0.03 dia. holes
4.2
2.8
0.6
2.8
2.8
2.8
OP
8.4
10.3±0.1
15.9 19.1
+0.13
3.1 –0.03
3.4±0.15 dia.
22.2±0.1 2.8 (12.0)
27.8
t=0.8
Three, quick-connect
terminals (#250)
10.3
Characteristics
39.8±0.8
V-21-1@6
V-16-1@5
OF max.
400 gf
200 gf
RF min.
80 gf
1.2 mm
OT min.
1.0 mm
MD max.
0.4 mm
14.7 ± 0.4 mm
OP
(With Right-hand Barrier)
V-21-1 R6
V-16-1 R5
A
PT
50 gf
PT max.
20.2±0.25
+0.13
3.1 –0.03 dia. holes
2.8
4.2
1.6
0.6
2.8
2.8
2.8
OP
8.4
10.3±0.1
15.9
19.1
Characteristics
21.9
+0.13
3.1 –0.03
0.6
3.4±0.15 dia.
22.2±0.1 2.8
27.8
t=0.8
Three, quick-connect
(12.0)
terminals (#250)
10.3
(With Left-hand Barrier)
+0.13
2.8
3.1 –0.03 dia. holes
1.6
20 gf
50 gf
PT max.
1.2 mm
OT min.
1.0 mm
0.4 mm
14.7 ± 0.4 mm
A
2.8
PT
2.8
19.1
21.9
20.2±0.25
2.8
0.6
200 gf
RF min.
OP
40.2
4.2
V-11-1@5
100 gf
MD max.
39.8±0.8
V-21-1 L6
V-16-1 L5
V-11-1@4
OF max.
8.4
15.9
10.3±0.1
OP
+0.13
3.1 –0.03
t=0.8
Three, quick-connect
terminals (#250)
0.6
10.3
3.4±0.15 dia.
(12.0) 2.8 22.2±0.1
27.8
39.8±0.8
40.2
Snap Action Switch
V
129
➡
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
2. The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate terminals A and C2,
which are omitted from the following drawings. Refer to Terminals section for the dimensions of these terminals.
3. The @ in the model number is for the terminal code.
4. The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix “K” have a hole size of 2.9 mm.
5. The operating characteristics are for operation in the A direction (
).
Short Hinge Lever Models
V-211-1 6
V-161-1 5
V-111-1 4
22.1
A
PT
2.8
t = 0.5
(see
note)
Characteristics V-211-1@6 V-161-1@5 V-111-1@4
8.1
3.1 +0.13
–0.03
1.6
4.3
dia. holes
0.6
2.8
2.8
OP
10.3±0.1
8.4
15.9
19.1
OF max.
400 gf
200 gf
100 gf
RF min.
50 gf
50 gf
15 gf
PT max.
1.6 mm
OT min.
0.8 mm
MD max.
+0.13
3.1 –0.03
3.4±0.15 dia.
0.6 mm
15.2 ± 0.5 mm
OP
t=0.8
Three, quick-connect
terminals (#250)
22.2±0.1 2.8 (12.0)
27.8
39.8±0.8
Note:
10.3
Stainless-steel lever
Hinge Lever Models
V-212-1 6
V-162-1 5
V-112-1 4
35.6±0.8
PT
8.1
t = 0.5
(see note)
A
1.6
Characteristics V-212-1@6 V-162-1@5 V-112-1@4
+0.13
3.1 –0.03 dia. holes
4.3
0.6
2.8
2.8
2.8
OP
8.4
10.3±0.1
15.9
19.1
+0.13
OF max.
250 gf
125 gf
60 gf
RF min.
25 gf
14 gf
6 gf
PT max.
4.0 mm
OT min.
1.6 mm
MD max.
3.1 –0.03
3.4±0.15 dia.
22.2±0.1
(12.0)
2.8
27.8
39.8±0.8
t=0.8
Three, quick-connect
terminals (#250)
Note:
1.5 mm
15.2 ± 1.2 mm
OP
10.3
Stainless-steel lever
Long Hinge Lever Models
V-213-1 6
V-163-1 5
V-113-1 4
59.4±0.8
A
PT
2.8
1.6
+0.13
3.1 –0.03 dia. holes
t = 0.5 (see note)
2.8
OP
8.4 15.9
10.3±0.1
Characteristics V-213-1@6 V-163-1@5 V-113-1@4
4.3
0.6
2.8
OF max.
130 gf
70 gf
35 gf
RF min.
12 gf
6 gf
---
PT max.
19.1
OT min.
+0.13
3.1 –0.03
3.4±0.15 dia.
22.2±0.1 2.8
27.8
39.8±0.8
130
Snap Action Switch
V
(12.0)
t=0.8
Three, quick-connect
terminals (#250)
Note:
MD max.
10.3
Stainless-steel lever
OP
9.0 mm
2.0 mm
3.2 mm
2.8 mm
+2.6
15.2 −3.2 mm
15.2 ± 2.6 mm
➡
Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
2. The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate terminals A and C2,
which are omitted from the following drawings. Refer to Terminals section for the dimensions of these terminals.
3. The @ in the model number is for the terminal code.
4. The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix “K” have a hole size of 2.9 mm.
5. The operating characteristics are for operation in the A direction (
).
Simulated Roller Lever Models
V-214-1 6
V-164-1 5
V-114-1 4
32.6±0.8
3.5R
PT
OP
A
Characteristics V-214-1@6 V-164-1@5 V-114-1@4
8.1
t = 0.5
(see note)
1.6
3.1 +0.13
–0.03 dia. holes
4.3
2.8
0.6
2.8
2.8
8.4
15.9
10.3±0.1
19.1
OF max.
250 gf
125 gf
60 gf
RF min.
25 gf
14 gf
6 gf
PT max.
4.0 mm
OT min.
1.6 mm
MD max.
+0.13
3.1 –0.03
1.5 mm
18.7 ± 1.2 mm
OP
3.4±0.15 dia.
22.2±0.1 2.8
27.8
t=0.8
Three, quick-connect
terminals (#250)
(12.0)
10.3
39.8±0.8
Note:
Stainless-steel lever
Short Hinge Roller Lever Models
V-215-1 6
V-165-1 5
V-115-1 4
Characteristics V-215-1@6 V-165-1@5 V-115-1@4
20.1
A t = 0.5
(see 8.1
note 1)
PT
1.6
+0.13
3.1 –0.03
5.1
0.6
4.8 dia. × 4.8
(see note 2)
dia. holes
2.8
2.8
OP
8.4 15.9
10.3±0.1
OF max.
480 gf
240 gf
120 gf
RF min.
50 gf
50 gf
15 gf
PT max.
1.6 mm
OT min.
0.8 mm
MD max.
19.1
0.6 mm
20.7 ± 0.6 mm
OP
+0.13
3.1 –0.03
3.4±0.15 dia.
22.2±0.1
27.8
2.8
t=0.8
Three, quick-connect
terminals (#250)
(12.0)
39.8±0.8
Note:
10.3
1. Stainless-steel lever
2. Oilless polyacetar resin roller
Hinge Roller Lever Models
V-216-1 6
V-166-1 5
V-116-1 4
34.0±0.8
PT
A
t = 0.5
(see note 1)
8.1
1.6
0.6
dia. holes
2.8
OP 2.8
10.3±0.1
Characteristics V-216-1@6 V-166-1@5 V-116-1@4
5.1
+0.13
3.1 –0.03
8.4
4.8 dia. × 4.8
(see note 2)
15.9 19.1
+0.13
OF max.
250 gf
125 gf
60 gf
RF min.
25 gf
14 gf
6 gf
PT max.
4.0 mm
OT min.
1.6 mm
MD max.
3.1 –0.03
3.4±0.15 dia.
22.2±0.1
2.8
27.8
39.8±0.8
10.3
t=0.8
(12.0) Three, quick-connect
terminals (#250)
Note:
OP
1.5 mm
20.7 ± 1.2 mm
1. Stainless-steel lever
2. Oilless polyacetar resin roller
Snap Action Switch
V
131
Thermosetting Case Models
Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
The following illustrations are for quick-connect terminals (#250) (terminals C). Refer to Terminals section for the dimensions of other terminals.
The @ in the model number is for the terminal code.
The illustrations show models with a suffix “K”, which have a hole size of 2.9 mm. Omit the “K” to obtain models with hole size = 3.1 mm.
The operating characteristics are for operation in the A direction (
).
➡
Note: 1.
2.
3.
4.
5.
Pin Plunger Models
20.2±0.25
V-15G-1 5-K
V-10G-1 5-K
V-10G-1 4-K
4.2
PT
2.8
A
OP
2.8
Characteristics
+0.13
2.9 –0.03 dia. holes
V-15G-1@5-K
V-10G-1@5-K
V-10G-1@4-K
100 gf
2.8
OF max.
200 gf
10.3±0.1
RF min.
50 gf
15.9 18.8
+0.13
3.1 –0.03
3.4±0.15 dia.
22.2±0.1
2.8
27.8
10.3
t=0.5
Three, solder
terminals
(10)
20 gf
PT max.
1.2 mm
OT min.
1.3 mm
MD max.
0.3 mm
14.7 ± 0.4 mm
OP
37.8±0.8
Short Hinge Lever Models
t = 0.5 (see note)
22.1
V-15G1-1 5-K
V-10G1-1 5-K
V-10G1-1 4-K
PT
A
4.3 2.8
+0.13
Characteristics
2.9 –0.03 dia. holes
8.1
V-15G1-1@5-K
V-10G1-1@5-K
V-10G1-1@4-K
100 gf
2.8
OF max.
200 gf
10.3±0.1
RF min.
50 gf
OP
15.9
18.8
+0.13
3.1 –0.03
3.4±0.15 dia.
22.2±0.1
27.8
2.8
10.3
t=0.5
Three, solder terminals
15 gf
PT max.
1.5 mm
OT min.
1.0 mm
MD max.
0.5 mm
15.2 ± 0.5 mm
OP
(10)
37.8±0.8
Note:
Stainless-steel lever
Hinge Lever Models
t = 0.5 (see note)
V-15G2-1 5-K
V-10G2-1 5-K
V-10G2-1 4-K
35.6±0.8
PT
4.3
8.1
2.8
OP
10.3±0.1
V-15G2-1@5-K
V-10G2-1@5-K
V-10G2-1@4-K
OF max.
125 gf
60 gf
RF min.
14 gf
Characteristics
+0.13
2.9 –0.03 dia. holes
A
15.9
18.8
3.1 +0.13
–0.03
2.8
3.3 mm
OT min.
2.3 mm
MD max.
3.4±0.15 dia.
10.3
22.2±0.1
2.8
t=0.5
Three, solder terminals
6 gf
PT max.
OP
0.8 mm
+2.6
15.2 −3.2 mm
15.2 ± 1.2 mm
27.8
(10)
Note:
Stainless-steel lever
37.8±0.8
Long Hinge Lever Models
V-15G3-1 5-K
V-10G3-1 5-K
V-10G3-1 4-K
A
PT
OP
2.8
t = 0.5 (see note)
59.4±0.8
8.1
+0.13
2.9 –0.03 dia. holes
4.3
2.8
10.3±0.1
15.9 18.8
+0.13
3.1 –0.03
2.8
3.4±0.15 dia.
22.2±0.1
27.8
37.8±0.8
132
Snap Action Switch
V
(10)
10.3
t=0.5
Three, solder terminals
Note:
Stainless-steel lever
Characteristics
V-15G3-1@5-K
V-10G3-1@5-K
V-10G3-1@4-K
OF max.
70 gf
35 gf
RF min.
6 gf
- - - gf
PT max.
9.0 mm
7.6 mm
OT min.
3.0 mm
MD max.
OP
3.2 mm
2.0 mm
15.2 ± 2.6 mm
Unless otherwise specified, all units are in millimeters and a tolerance of ±0.4 mm applies to all dimensions
The following illustrations are for quick-connect terminals (#250) (terminals C). Refer to Terminals section for the dimensions of other terminals.
The @ in the model number is for the terminal code.
The illustrations show models with a suffix “K”, which have a hole size of 2.9 mm. Omit the “K” to obtain models with hole size = 3.1 mm.
The operating characteristics are for operation in the A direction (
).
➡
Note: 1.
2.
3.
4.
5.
Simulated Roller Lever Models
3.5R
V-15G4-1 5-K
V-10G4-1 5-K
V-10G4-1 4-K
t = 0.5 (see note)
A
PT
V-10G4-1@4-K
OF max.
125 gf
60 gf
RF min.
14 gf
2.9 –0.03 dia. holes
8.1
2.8
2.8
OP
V-15G4-1@5-K
V-10G4-1@5-K
Characteristics
4.3
+0.13
32.6±0.8
10.3±0.1
15.9 18.8
3.1 +0.13
–0.03
2.8
22.2±0.1
27.8
(10)
37.8±0.8
3.3 mm
OT min.
2.3 mm
MD max.
10.3
3.4±0.15 dia.
t=0.5
Three, solder terminals
Note:
6 gf
PT max.
0.8 mm
18.7 ± 1.2 mm
OP
Stainless-steel lever
Short Hinge Roller Lever Models
V-15G5-1 5-K
V-10G5-1 5-K
V-10G5-1 4-K
4.8 dia. × 4.8 (see note 2)
t = 0.5 (see note 1)
A
5.1
20.1
+0.13
2.9 –0.03 dia. holes
8.1
PT
OP
2.8
10.3±0.1
15.9 18.8
3.1 +0.13
–0.03
2.8
3.4±0.15 dia.
22.2±0.1
27.8
V-10G5-1@4-K
OF max.
240 gf
120 gf
RF min.
50 gf
1.5 mm
OT min.
1.0 mm
0.5 mm
20.7 ± 0.6 mm
OP
t=0.5
Three, solder terminals
15 gf
PT max.
MD max.
10.3
(10)
V-15G5-1@5-K
V-10G5-1@5-K
Characteristics
37.8±0.8
Note:
1. Stainless-steel lever
2. Oilless polyacetar resin roller
Hinge Roller Lever Models
V-15G6-1 5-K
V-10G6-1 5-K
V-10G6-1 4-K
4.8 dia. × 4.8 (see note 2)
t = 0.5 (see note 1)
A
34.0±0.8
PT
8.1
OP
2.9 +0.13
–0.03
5.1
dia. holes
2.8
10.3±0.1
15.9 18.8
+0.13
3.1 –0.03
2.8
3.4±0.15 dia.
22.2±0.1
27.8
(10)
10.3
t=0.5
Three, solder terminals
V-15G6-1@5-K
V-10G6-1@5-K
V-10G6-1@4-K
OF max.
125 gf
60 gf
RF min.
14 gf
Characteristics
6 gf
PT max.
3.3 mm
OT min.
2.3 mm
MD max.
OP
0.8 mm
20.7 ± 1.6 mm
37.8±0.8
Note:
1. Stainless-steel lever
2. Oilless polyacetar resin roller
Accessories
Refer to the “V/VX/D3C Common Accessories” datasheet for information regarding VAL, VAM and VAV external actuators (sold separately).
Snap Action Switch
V
133
Precautions
Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User’s Guide,
“Snap Action Switches, Technical Information” for correct use.
■ Correct Use
■ Cautions
Terminal Connection
Insulation Distance
To solder the lead to the solder terminal, apply a soldering iron rated
at 60 W max. quickly (within 5 seconds) with the actuator at the free
position.
According to EN61058-1, the minimum insulation thickness for this
switch should be 1.1 mm and minimum clearance distance between
the terminal and mounting plate should be 1.0 mm. If the insulation
distance cannot be provided in the product incorporating the switch,
either use a switch with insulation barrier or use a separator to
ensure sufficient insulation distance.
Note that applying a soldering iron for too long a time or using one
that is rated at more than 60 W may degrade the switch characteristics.
Use an appropriate mating connector for #187 or #250 quick connect
terminals.
Specifications Approved by TÜV Rheinland
According to EN61058-1
Appropriate Cable Size (mm2)
Model
Solder terminal
V-10
0.75, 1.25, 2.0
V-15
1.25, 2.0
Operation
Make sure that the operating body pushes the switch actuator with
an adequate force when the switch is to be operated, and that it does
not touch the actuator when the switch is released.
Do not change the operating position by modifying the actuator.
Do not use the switch in a application where the operating speed is
extremely slow or the actuator is set in the midpoint between the free
position and operating position.
Install the pin plunger switch so that the operating force is applied in
alignment with the stroke of the actuator. The switch should be set so
that its stroke is in the range of 60 to 90% of the rated OT (minimum
value) when the switch has been operated.
134
Snap Action Switch
V
Omron Electronic Components, LLC
Terms and Conditions of Sales
I. GENERAL
1. Definitions: The words used herein are defined as follows.
(a) Terms:
These terms and conditions
(b) Seller:
Omron Electronic Components LLC and its subsidiaries
(c) Buyer:
The buyer of Products, including any end user in section III through VI
(d) Products: Products and/or services of Seller
(e) Including: Including without limitation
2. Offer; Acceptance: These Terms are deemed part of all quotations, acknowledgments,
invoices, purchase orders and other documents, whether electronic or in writing, relating
to the sale of Products by Seller. Seller hereby objects to any Terms proposed in Buyer's
purchase order or other documents which are inconsistent with, or in addition to, these
Terms.
3. Distributor: Any distributor shall inform its customer of the contents after and including
section III of these Terms.
II. SALES
1. Prices; Payment: All prices stated are current, subject to change without notice by Seller.
Buyer agrees to pay the price in effect at the time the purchase order is accepted by
Seller. Payments for Products received are due net 30 days unless otherwise stated in
the invoice. Buyer shall have no right to set off any amounts against the amount owing in
respect of this invoice.
2. Discounts: Cash discounts, if any, will apply only on the net amount of invoices sent to
Buyer after deducting transportation charges, taxes and duties, and will be allowed only
if (a) the invoice is paid according to Seller's payment terms and (b) Buyer has no past
due amounts owing to Seller.
3. Interest: Seller, at its option, may charge Buyer 1.5% interest per month or the maximum
legal rate, whichever is less, on any balance not paid within the stated terms.
4. Orders: Seller will accept no order less than 200 U.S. dollars net billing.
5. Currencies: If the prices quoted herein are in a currency other than U.S. dollars, Buyer
shall make remittance to Seller at the then current exchange rate most favorable to
Seller; provided that if remittance is not made when due, Buyer will convert the amount
to U.S. dollars at the then current exchange rate most favorable to Seller available
during the period between the due date and the date remittance is actually made.
6. Governmental Approvals: Buyer shall be responsible for all costs involved in obtaining
any government approvals regarding the importation or sale of the Products.
7. Taxes: All taxes, duties and other governmental charges (other than general real
property and income taxes), including any interest or penalties thereon, imposed directly
or indirectly on Seller or required to be collected directly or indirectly by Seller for the
manufacture, production, sale, delivery, importation, consumption or use of the Products
sold hereunder (including customs duties and sales, excise, use, turnover and license
taxes) shall be charged to and remitted by Buyer to Seller.
8. Financial: If the financial position of Buyer at any time becomes unsatisfactory to Seller,
Seller reserves the right to stop shipments or require satisfactory security or payment in
advance. If Buyer fails to make payment or otherwise comply with these Terms or any
related agreement, Seller may (without liability and in addition to other remedies) cancel
any unshipped portion of Products sold hereunder and stop any Products in transit until
Buyer pays all amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all unpaid
accounts.
9. Cancellation; Etc: Orders are not subject to rescheduling or cancellation unless Buyer
indemnifies Seller fully against all costs or expenses arising in connection therewith.
10. Force Majeure: Seller shall not be liable for any delay or failure in delivery resulting from
causes beyond its control, including earthquakes, fires, floods, strikes or other labor
disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots,
delay in or lack of transportation or the requirements of any government authority.
11. Shipping; Delivery: Unless otherwise expressly agreed in writing by Seller:
(a) All sales and shipments of Products shall be FOB shipping point (unless otherwise
stated in writing by Seller), at which point title to and all risk of loss of the Products
shall pass from Seller to Buyer, provided that Seller shall retain a security interest in
the Products until the full purchase price is paid by Buyer;
(b) Delivery and shipping dates are estimates only; and
(c) Seller will package Products as it deems proper for protection against normal
handling and extra charges apply to special conditions.
12. Claims: Any claim by Buyer against Seller for shortage or damage to the Products
occurring before delivery to the carrier or any claim related to pricing or other charges
must be presented in detail in writing to Seller within 30 days of receipt of shipment.
III. PRECAUTIONS
1. Suitability: IT IS THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY
OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE
APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING
APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE
BUYER’S APPLICATION INCLUDING (A) ELECTRICAL OR ELECTRONIC
COMPONENTS, (B) CIRCUITS, (C) SYSTEM ASSEMBLIES, (D) END PRODUCT, (E)
SYSTEM, (F) MATERIALS OR SUBSTANCES OR (G) OPERATING ENVIRONMENT.
Buyer acknowledges that it alone has determined that the Products will meet their
requirements of the intended use in all cases. Buyer must know and observe all
prohibitions of use applicable to the Product/s.
2. Use with Attention: The followings are some examples of applications for which
particular attention must be given. This is not intended to be an exhaustive list of all
possible use of any Product, nor to imply that any use listed may be suitable for any
Product:
(a) Outdoor use, use involving potential chemical contamination or electrical
interference.
(b) Use in consumer Products or any use in significant quantities.
(c) Energy control systems, combustion systems, railroad systems, aviation systems,
medical equipment, amusement machines, vehicles, safety equipment, and
installations subject to separate industry or government regulations.
(d) Systems, machines, and equipment that could present a risk to life or property.
3. Prohibited Use: NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE
PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE
WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
4. Motorized Vehicle Application: USE OF ANY PRODUCT/S FOR A MOTORIZED
VEHICLE APPLICATION MUST BE EXPRESSLY STATED IN THE SPECIFICATION BY
SELLER.
5. Programmable Products: Seller shall not be responsible for the Buyer's programming of
a programmable Product.
IV. WARRANTY AND LIMITATION
1. Warranty: Seller's exclusive warranty is that the Products will be free from defects in
materials and workmanship for a period of twelve months from the date of sale by Seller
(or such other period expressed in writing by Seller). SELLER MAKES NO WARRANTY
OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT ALL OTHER WARRANTIES,
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OF THE PRODUCTS.
2. Buyer Remedy: Seller's sole obligation hereunder shall be to replace (in the form
originally shipped with Buyer responsible for labor charges for removal or replacement
thereof) the non-complying Product or, at Seller's election, to repay or credit Buyer an
amount equal to the purchase price of the Product; provided that there shall be no
liability for Seller or its affiliates unless Seller's analysis confirms that the Products were
correctly handled, stored, installed and maintained and not subject to contamination,
abuse, misuse or inappropriate modification. Return of any Products by Buyer must be
approved in writing by Seller before shipment.
3. Limitation on Liability: SELLER AND ITS AFFILIATES SHALL NOT BE LIABLE FOR
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF
PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED
WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, NEGLIGENCE OR STRICT LIABILITY. FURTHER, IN NO EVENT SHALL
LIABILITY OF SELLER OR ITS AFFILITATES EXCEED THE INDIVIDUAL PRICE OF
THE PRODUCT ON WHICH LIABILITY IS ASSERTED.
4. Indemnities: Buyer shall indemnify and hold harmless Seller, its affiliates and its
employees from and against all liabilities, losses, claims, costs and expenses (including
attorney's fees and expenses) related to any claim, investigation, litigation or proceeding
(whether or not Seller is a party) which arises or is alleged to arise from Buyer's acts or
omissions under these Terms or in any way with respect to the Products.
V. INFORMATION; ETC.
1. Intellectual Property: The intellectual property embodied in the Products is the exclusive
property of Seller and its affiliates and Buyer shall not attempt to duplicate it in any way
without the written permission of Seller. Buyer (at its own expense) shall indemnify and
hold harmless Seller and defend or settle any action brought against Seller to the extent
that it is based on a claim that any Product made to Buyer specifications infringed
intellectual property rights of another party.
2. Property; Confidentiality: Notwithstanding any charges to Buyer for engineering or
tooling, all engineering and tooling shall remain the exclusive property of Seller. All
information and materials supplied by Seller to Buyer relating to the Products are
confidential and proprietary, and Buyer shall limit distribution thereof to its trusted
employees and strictly prevent disclosure to any third party.
3. Performance Data: Performance data is provided as a guide in determining suitability
and does not constitute a warranty. It may represent the result of Seller's test conditions,
and the users must correlate it to actual application requirements.
4. Change In Specifications: Product specifications and descriptions may be changed at
any time based on improvements or other reasons. It is Seller’s practice to change part
numbers when published ratings or features are changed, or when significant
engineering changes are made. However, some specifications of the Product may be
changed without any notice.
5. Errors And Omissions: The information on Seller’s website or in other documentation
has been carefully checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
6. Export Controls: Buyer shall comply with all applicable laws, regulations and licenses
regarding (a) export of the Products or information provided by Seller; (b) sale of
Products to forbidden or other proscribed persons or organizations; (c) disclosure to noncitizens of regulated technology or information.
VI. MISCELLANEOUS
1. Waiver: No failure or delay by Seller in exercising any right and no course of dealing
between Buyer and Seller shall operate as a waiver of rights by Seller.
2. Assignment: Buyer may not assign its rights hereunder without Seller's written consent.
3. Law: These Terms are governed by Illinois law (without regard to conflict of laws).
Federal and state courts in Cook County, Illinois have exclusive jurisdiction for any
dispute hereunder.
4. Amendment: These Terms constitute the entire agreement between Buyer and Seller
relating to the Products, and no provision may be changed or waived unless in writing
signed by the parties.
5. Severability: If any provision hereof is rendered ineffective or invalid, such provision shall
not invalidate any other provision.
Snap Action Switch
V
Certain Precautions on Specifications and Use
1. Suitability for Use. Seller shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in
Buyer's application or use of the Product. At Buyer's request, Seller will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use.
Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer's application, product or system. Buyer
shall take application responsibility in all cases but the following is a nonexhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety
equipment, and installations subject to separate industry or government
regulations.
(iii) Use in consumer products or any use in significant quantities.
(iv) Systems, machines and equipment that could present a risk to life or
property. Please know and observe all prohibitions of use applicable to this
product.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM
AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT
THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE
INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Seller shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
3. Performance Data. Performance data given in this publication is provided as
a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Seller's test conditions, and the users must
correlate it to actual application requirements. Actual performance is subject to
Seller's Warranty and Limitations of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Seller representative at any time to
confirm actual specifications of purchased Product.
5. Errors and Omissions. The information in this publication has been carefully
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors, or omissions.
6. RoHS Compliance. Where indicated, our products currently comply, to the
best of our knowledge as of the date of this publication, with the requirements
of the European Union's Directive on the Restriction of certain Hazardous
Substances ("RoHS"), although the requirements of RoHS do not take effect
until July 2006. These requirements may be subject to change. Please consult
our website for current information.
Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website
at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
OMRON ON-LINE
OMRON ELECTRONIC
COMPONENTS LLC
Global - http://www.omron.com
USA - http://www.components.omron.com
55 E. Commerce Drive, Suite B
Schaumburg, IL 60173
847-882-2288
Cat. No. X303-E-1
11/09
Snap Action Switch
V
Specifications subject to change without notice
Printed in USA