PROTEC U0402FC15C

05149
U0402FC3.3C - U0402FC36C
Only One Name Means ProTek’Tion™
250w unbumped flip chip tvs array
Description
The U0402FCxxC Series Flip Chips employ advanced silicon P/N junction technology for unmatched board-level
transient voltage protection against Electrostatic Discharge (ESD) and Electrical Fast Transients (EFT). Developed
specifically for high-density circuit protection, this series meets the IEC 61000-4-2 and 61000-4-4 requirements. These
devices are ideally suited for handheld devices, PCMCIA and SMART cards.
This series provides ESD protection greater than 25 kilovolts with a peak pulse power dissipation of 250 Watts per
line for an 8/20µs waveform. In addition, the U0402FCxxC series features superior clamping performance, low leakage current characteristics and a response time of less than a nanosecond. Their low inductance virtually eliminates
overshoot voltage due to package inductance.
U0402 package
Features
applications
• Compatible with IEC 61000-4-2 (ESD): Air 15kV, Contact 8kV
• Compatible with IEC 61000-4-4 (EFT): 40A, 5/50ns
• ESD Protection > 25 kilovolts
• Available in Voltages Ranging from 3.3V to 36V
• 250 Watts Peak Pulse Power per Line (tp = 8/20µs)
• Bidirectional Configuration and Monolithic Structure
• Protection for 1 Line
• RoHS Compliant
• REACH Compliant
• Cellular Phones
• MCM Boards
• Wireless Communication Circuits
• IR LEDs
• SMART & PCMCIA Cards
Mechanical characteristics
• Standard EIA Chip Size: 0402
• Approximate Weight: 0.73 milligrams
• Lead-Free Plating
• Solder Reflow Temperature:
• Lead-Free - Sn/Ag/Cu, 96/3.5/0.5: 260-270°C
• Flammability Rating UL 94V-0
• 8mm Plastic Tape per EIA Standard 481
PIN CONFIGURATION
05149.R6 2/11
Page 1
www.protekdevices.com
05149
U0402FC3.3C - U0402FC36C
Only One Name Means ProTek’Tion™
typical device characteristics
MAXIMUM RATINGS @ 25°C Unless Otherwise Specified
PARAMETER
Peak Pulse Power (tp = 8/20µs) - See Figure 1
Operating Temperature
Storage Temperature
SYMBOL
VALUE
UNITS
PPP
250
Watts
TA
-55 to 150
°C
TSTG
-55 to 150
°C
ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified
PART
NUMBER
(Note 1)
RATED
STAND-OFF
VOLTAGE
MINIMUM
BREAKDOWN
VOLTAGE
@ 1mA
V(BR)
VOLTS
MAXIMUM
CLAMPING
VOLTAGE
(Fig. 2)
@ IP = 1A
VC
VOLTS
MAXIMUM
CLAMPING
VOLTAGE
(Fig. 2)
V WM
VOLTS
U0402FC3.3C
U0402FC05C
U0402FC08C
U0402FC12C
MAXIMUM
LEAKAGE
CURRENT
(Note 2)
@V WM
ID
µA
TYPICAL
CAPACITANCE
3.3
4.0
7.0
5.0
6.0
9.8
12.5V @ 20A
75*
150
14.7V @ 17A
10**
100
8.0
8.5
13.4
19.2V @ 13A
10***
75
12.0
13.3
19.0
29.7V @ 9A
1
50
@ 8/20µs
VC @ I PP
@0V, 1MHz
C
pF
U0402FC15C
15.0
16.7
24.0
35.7V @ 7A
1
40
U0402FC24C
24.0
26.7
43.0
55.0V @ 5A
1
30
U0402FC36C
36.0
40.0
64.0
84.0V @ 3A
1
25
notes
1. All devices are bidirectional. Electrical characteristics apply in both directions.
2. *Maximum leakage current < 5µA @ 2.8V. **Maximum leakage current < 500nA @ 3.3V. ***Maximum leakage current < 200nA @ 5V.
05149.R6 2/11
Page 2
www.protekdevices.com
05149
U0402FC3.3C - U0402FC36C
Only One Name Means ProTek’Tion™
typical device characteristics
figure 1
peak pulse power vs pulse time
PPP - Peak Pulse Power - Watts
10,000
1,000
250W, 8/20µs Waveform
100
10
0.1
10
100
td - Pulse Duration - µs
Peak Value IPP
80
100
TEST
WAVEFORM
PARAMETERS
tf = 8µs
td = 20µs
e-t
60
40
10,000
figure 3
power derating curve
Peak Pulse Power
8/20µs
80
% Of Rated Power
tf
100
td = t/(IPP/2)
60
40
20
20
0
1,000
figure 2
pulse wave form
120
IPP - Peak Pulse Current - % of IPP
1
0
05149.R6 2/11
5
10
15
t - Time - µs
20
25
0
30
Page 3
Average Power
0
25
50
75 100 125
TA - Ambient Temperature - °C
150
www.protekdevices.com
05149
U0402FC3.3C - U0402FC36C
Only One Name Means ProTek’Tion™
typical device characteristics
figure 4
overshoot & clamping voltage for u0402fc05c
35
5 Volts per Division
25
15
5
-5
ESD Test Pulse - 25 kilovolt, 1/30ns (Waveshape)
figure 5
typical clamping voltage vs peak pulse current u0402fc05c
VC - Clamping Voltage - Volts
12
8
4
0
0
05149.R6 2/11
5
10
IPP - Peak Pulse Current - Amps
Page 4
15
20
www.protekdevices.com
05149
U0402FC3.3C - U0402FC36C
Only One Name Means ProTek’Tion™
SOLDER REFLOW INFORMATION
printed circuit board recommendations
parameter
value
Pad Size on PCB
0.275mm
Pad Shape
Round
Pad Definition
Non-Solder Mask Defined Pads
Solder Mask Opening
0.325mm Round
Solder Stencil Thickness
0.150mm
Solder Stencil Aperture Opening (Laser cut, 5% tapered walls)
0.330mm Round
Solder Paste Type
No Clean
Pad Protective Finish
OSP (Entek Cu Plus 106A)
Tolerance - Edge To Corner Ball
±50µm
Solder Ball Side Coplanarity (Only applies to bumped devices)
±20µm
Maximum Dwell Time Above Liquidous (183°C)
60 seconds
Soldering Maximum Temperature
270°C
Requirements
recommended non-solder mask
defined pad illustration
Temperature:
TP for Lead-Free (Sn/Ag/Cu): 260-270°C
Preheat time and temperature depends on solder paste and flux activation temperature, component size, weight, surface area and plating.
Non-Solder Mask Defined Pad
0.275mm DIA.
Solder Mask Opening
0.325mm DIA.
Solder Stencil Opening
0.330mm DIA.
Maximum Solder Reflow
(35-53°C Above Maximum Solder Melt Temp)
TP
Solder Melt
(Maximum Temp)
Temperature - °C
Ramp-Up
Ramp-Down
Preheat
(Stay Below Flux Activation Temp)
30-60 seconds
05149.R6 2/11
Ramp-Up
15 seconds
(Minimize)
Page 5
Solder-Time
15-20 seconds
Ramp-Down
www.protekdevices.com
05149
U0402FC3.3C - U0402FC36C
Only One Name Means ProTek’Tion™
U0402 package information
outline dimensions
millimeters
min
max
inches
min
max
A
0.61
0.024
B
0.86
0.034
C
0.98
1.02
0.038
D
0.10
0.004
E
0.35
0.014
F
0.458
I
0.508
0.018
0.406
TOP
0.040
A
SIDE
dim
B C
0.020
0.016
Notes
1. Controlling dimensions in inches.
2. Decimal tolerance: .xxx ± 0.05mm (0.002”).
3. Maximum chip size: 1.02mm (0.040”) by 0.51mm (0.020”).
D
E
F
Metalized Die Contacts
END
C
B
layout dimensions
inches
nominal
nominal
A
0.23
0.009
B
0.48
0.019
C
0.69
0.027
D
0.46
0.018
E
0.99
0.039
F
0.20
0.008
G
0.20
0.008
H
0.66
0.026
I
0.13
0.005
D
A
SOLDER PAD
millimeters
dim
I
DIE
DIE
CONTACTS
F
E
H
I
Notes
1. Controlling dimensions in inches.
2. Decimal tolerance: .xxx ± 0.05mm (0.002”).
05149.R6 2/11
SOLDER PRINT
DIAMETER 0.010” - 0.012”
Page 6
G
www.protekdevices.com
05149
U0402FC3.3C - U0402FC36C
Only One Name Means ProTek’Tion™
TAPE AND REEL information
P0
D
T
10 Pitches Cumulative
Tolerance on tape ± 0.2
E
P2
Top Cover
Tape
F
A0
K0
W
B0
P
User Direction of Feed
specifications
Reel Dia.
Tape
Width
178(7”)
8
A0
B0
K0
D
E
F
P0
P2
P
tmax
0.70 ± 0.05 1.15 ± 0.10 0.56 ± 0.05 1.55 ± 0.05 1.75 ± 0.10 3.50 ± 0.05 8.00 ± 0.20 4.00 ± 0.05 2.00 ± 0.05 2.00 ± 0.05
Notes
1.
2.
3.
4.
5.
6.
W
0.25
tape & reel orientation
Dimensions in millimeters.
Top view of tape. Metal contacts are face down in tape package.
Orientation: preferred stencil - 0.1mm (0.004”).
Surface mount product is taped and reeled in accordance with EIA 481.
8mm plastic tape: 7” Reels - 5,000 (pocket under hole skipped) or 10,000 pieces per reel.
Marking on Reel - part number, date code and lot number.
Single Die - 0402
Package outline, pad layout and tape specifications per document number 06020.R5 9/09.
ORDERING INFORMATION
base PART NUMBER
(xx = voltage)
LEADFREE SUFFIX
TAPE SUFFIX
QTY/REEL
REEL SIZE
TUBE qty
U0402FCxxC
-LF
-T75-1
5,000
7”
n/a
U0402FCxxC
-LF
-T710-1
10,000
7”
n/a
05149.R6 2/11
Page 7
www.protekdevices.com
05149
U0402FC3.3C - U0402FC36C
Only One Name Means ProTek’Tion™
company information
COMPANY PROFILE
ProTek Devices, based in Tempe, Arizona USA, is a manufacturer of Transient Voltage Suppression (TVS) products designed specifically for
the protection of electronic systems from the effects of lightning, Electrostatic Discharge (ESD), Nuclear Electromagnetic Pulse (NEMP), inductive switching and EMI/RFI. With over 25 years of engineering and manufacturing experience, ProTek designs TVS devices that provide
application specific protection solutions for all electronic equipment/systems.
ProTek Devices Analog Products Division, also manufactures analog interface, control, RF and power management products.
CONTACT US
Corporate Headquarters
2929 South Fair Lane
Tempe, Arizona 85282
USA
By Telephone
General: 602-431-8101
Sales: 602-414-5109
Customer Service: 602-414-5114
By Fax
General: 602-431-2288
By E-mail:
Sales: [email protected]
Customer Service: [email protected]
Technical Support: [email protected]
Web
www.protekdevices.com
www.protekanalog.com
COPYRIGHT © ProTek Devices 2000 - This literature is subject to all applicable copyright laws and is not for resale in any manner.
SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice.
DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering
and technical assistance. ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek makes no warranty, representation or guarantee regarding the suitability of
its products for any particular purpose, nor does ProTek assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability without limitation special,
consequential or incidental damages.
LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without written consent from the factory.
PATENT INFORMATION: This device is patented under U.S. Patent No. Des. “D456,367S”.
05149.R6 2/11
Page 8
www.protekdevices.com