TS331 Low Power Low Offset Voltage Comparators SOT-25 Pin Definition: 1. Input + 2. Ground 3. Input 4. Output 5. Vcc General Description The TS331 is single precision voltage comparators capable of single-supply or split-supply operation. The specifications as low as 2.0 mV make this device an excellent ground level with single-supply operation. Input offsetvoltage selection for many applications in consumer automotive, and It is designed to permit a common mode rangeto- industrial electronics. Features ● Block Diagram Output voltage compatible with DTL, ECL, TTL, MOS and CMOS Logic levels ● Low input bias current 25nA ● Low input offset current ±0.5nA ● Low input offset voltage ±2mV(typ) ● Input common mode range to ground level ● Differential input voltage range equal to power supply voltage ● Very low supply current drain (0.4mA) - independent of supply voltage ● Wide single-supply range 2V~36V ● Split-supply range ±1V to ±18V Ordering Information Part No. TS331CX5 RF Package Packing SOT-25 3Kpcs / 7” Ree Absolute Maximum Rating Parameter Symbol Limit Unit Supply Voltage VCC +36 or ±18 V Differential Input Voltage VIDR 36 V Input Common Mode Voltage Range VICR -0.3 to 36 V Input Current IIN 50 mA Output Short Circuit to Ground ISC Continuous Output Sink Current ISINK 20 Operating Temperature Range TOPR -40 ~ +85 o C 150 o C -65 ~ +150 o C 260 o C Junction Temperature TJ Storage Temperature Range TSTG Lead Temperature 1.6mm(1/16”) from case for 10Sec. TLEAD 1/5 mA Version: A07 TS331 Low Power Low Offset Voltage Comparators Electrical Characteristics (VCC = 5V, Ta=25oC; unless otherwise specified.) Characteristics Symbol Min Typ Max Unit Input Offset Voltage (note 3) Vio -- 2 5 mV Input Offset Current, IIN(+) - IIN(-), VCM=0V Iio -- -- 50 nA Input Offset Current (note 4), IIN(+) - IIN(-), VCM=0V IIB -- -- 250 nA Input Common Mode Voltage Range, Vcc=30V VICR -0 -- VCC-1.5 V Voltage Gain, RL ≥15K, Vcc=15V, Vo=1V~11V AVOL 50 200 -- V/mV -- -- 300 -- nS Response Time (note 6), VRL=5V. RL=5.1KΩ tTLH -- 1.3 -- uS Output Sink Current, VIN(-)=1V, VIN(+)=0V, Vo≤1.5V ISINK 6.0 16 -- mA VOL -- 250 400 mV IOL -- 0.1 -- nA Icc -- 0.4 1.0 mA -- 1.0 2.5 Large Signal Response Time Vin=TTL Logic Swing. Vref = 1.4V, VRL=5V. RL=5.1KΩ Output Saturation Voltage, VIN(-)=1V, VIN(+)=0V, ISINK≤4mA Output Leakage Current, VIN(-)=0V, VIN(+)=1V, Vo=5V Supply Current RL = ∞, VCC =5V RL = ∞, VCC =36V Note 1. The max. Output current may be as high as 20mA, independent of the magnitude of VCC, output short circuits to VCC can cause excessive heating and eventual destruction. Note 2. This magnitude of input current will only occur if the input leads are driven more negative than ground or the negative supply voltage. This is due to the input PNP collector base junction becoming forward biased acting as an input clamp diode. There is also a lateral PNP parasitic transistor action on the IC chip. This phenomena can cause the output voltage of the comparators to go to the VCC voltage level (or ground if overdrive is large) during the time the input is driven negative. This will not destroy the device and normal output states will recover when the inputs become -0.3V of ground or negative supply. Note 3. At output switch point, VO=1.4Vdc, RS=0Ω with VCC from 5Vdc to 30Vdc, and over the full input common-mode Note 4. Due to the PNP transistor inputs, bias current will flow out of the inputs, this current is essentially constant independent of the output state, therefore, no loading changes will exist on the input lines. Note 5. Input common mode of either input should not be permitted to go more than 0.3V negative of ground or minus supply. The upper limit of common mode range is VCC - 1.5V but either or both inputs can betaken to as high as 30volts without damage. Note 6. Response time is specified with a 100mV step and 5.0mV of overdrive. With larger magnitudes of overdrive faster response times are obtainable. Application information This comparator feature high gain, wide bandwidth characteristics. This gives the device oscillation tendencies if the outputs are capacitive coupled to the inputs via stray capacitance. This oscillation manifests itself during output transitions (VOL to VOH). To alleviate this situation input resistors<10KΩ should be used. The addition of positive feedback (<10 mV) is also recommended. It is good design practice to ground all unused pins. Differential input voltages may be larger than supply voltage without damaging the comparator's inputs. Voltages more negative than -0.3V should not be used. 2/5 Version: A07 TS331 Low Power Low Offset Voltage Comparators Application information (continues) Figure 4. Zero Crossing Detector (Single Supply) Figure 7. Free-Running Square-Wave Oscillator Figure 6. Time Delay Generator Figure 8. Comparator with Hysteresis 3/5 Version: A07 TS331 Low Power Low Offset Voltage Comparators SOT-25 Mechanical Drawing DIM A+A1 B C D E E H L Ө1 S1 SOT-25 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX. 0.09 1.25 0.0354 0.0492 0.30 0.50 0.0118 0.0197 0.09 0.25 0.0035 0.0098 2.70 3.10 0.1063 0.1220 1.40 1.80 0.0551 0.0709 1.90 BSC 0.0748 BSC 2.40 3.00 0.09449 0.1181 0.35 BSC 0.0138 BSC 0º 10º 0º 10º 0.95 BSC 0.0374 BSC Marking Diagram 31 Y M L = Product Code for TS331CX5 = Year Code = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) = Lot Code 4/5 Version: A07 TS331 Low Power Low Offset Voltage Comparators Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 5/5 Version: A07